SAMA7G5 supports slew rate configuration. Adapt the driver for this.
For output switching frequencies lower than 50MHz the slew rate needs to
be enabled. Since most of the pins on SAMA7G5 fall into this category
enabled the slew rate by default.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/1611747945-29960-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I happened to apply the v1 of the patch restriction the
selection to ARM or ARM64, sorry for my sloppiness.
Fixing up the mistake as I can't back the patch out now.
Fixes: 5784921f7b ("pinctrl: actions: Add the platform dependency to drivers")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pcs_add_function() fails to set the function name in struct pcs_function
when adding a new function. As a result this line in pcs_set_mux():
dev_dbg(pcs->dev, "enabling %s function%i\n",
func->name, fselector);
prints "(null)" for the function:
pinctrl-single 44e10800.pinmux: enabling (null) function0
pinctrl-single 44e10800.pinmux: enabling (null) function1
pinctrl-single 44e10800.pinmux: enabling (null) function2
pinctrl-single 44e10800.pinmux: enabling (null) function3
With this fix, the output is now:
pinctrl-single 44e10800.pinmux: enabling pinmux-uart0-pins function0
pinctrl-single 44e10800.pinmux: enabling pinmux-mmc0-pins function1
pinctrl-single 44e10800.pinmux: enabling pinmux-i2c0-pins function2
pinctrl-single 44e10800.pinmux: enabling pinmux-mmc0-pins function3
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Robert Nelson <robertcnelson@beagleboard.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210125203542.51513-1-drew@beagleboard.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver for the sc8180x TLMM block.
A noteworthy difference from previous TLMM blocks is that the registers
for GPIO 177 through 189 are for some reason offset from the typical
layout. Other than that the driver is same old...
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210126042650.1725176-3-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pincontrol driver for tlmm block found in SM8350 SoC
This patch is based on initial code downstream by Raghavendra.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210205140132.274242-3-vkoul@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert spin_[lock|unlock] functions of pin bank to
raw_spinlock to support preempt-rt for pinctrl-s3c64xx. Below patch
converted spinlock_t to raw_spinlock_t but it didn't convert the
s3c64xx's spinlock.
Fixes: 1f306ecbe0 ("pinctrl: samsung: use raw_spinlock for locking")
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20210127001631.91209-1-chanho61.park@samsung.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Enable pin control on Intel Alder Lake-P
* Traverse through capabilities, convert them to features for the future use
The following is an automated git shortlog grouped by driver:
intel:
- Convert capability list to features
- Drop unnecessary check for predefined features
- Split intel_pinctrl_add_padgroups() for better maintenance
tigerlake:
- Add Alder Lake-P ACPI ID
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEqaflIX74DDDzMJJtb7wzTHR8rCgFAmAQEgEACgkQb7wzTHR8
rCgJcg/9Hw1Vi6Pe9l+SM7Gt4Cm/aRkYZGdfnDw0e1FgkAfdCmgi/zsBLYNIjiUD
cvjKLYf2JSgtA90dprPZWN0SBLdTpY1Yh88TzwGh23Pt8OnDoBP+JcrK07hH/cJ+
u0aUMd+MFNE+Vi3F1s4ENdABJ+uA9kJRpRzA/JGr2UgtII9N7hO+2iq+stfGNiIf
lonKkq+MgUfXxLYqRdkoIU/l0G+O86tSlMy1vhdOewyin06kL+FirGQgtoQg/WgD
qUXwG3qTZMcwum2q8TDtJioplRR/Vv1o888CdL6KWS25dsZZ13C8k0HNwR04nwFg
pzKqrq0Z0IeDNYNP2ThP6/FQ2L1haK4dHjSVdQsbRzI+lQaRL/OAmMBc5Q2HwwbD
c7XdJIFfB1ptq+gQF5tpZ0gZKbRNYZuperO/RfJuTPU+Vmtzk8aDi4Zu8GkilcaD
JFO5ZX+/6fs/k90TfCNCuoNAEAoKTHjofOh8BXqTtzKT24Sldtchz9YFD7UcvivN
H42hMq98XX1ZrcR0xQPLwfC43g4bRwIsZXInQ8z+BNOVpMEQgopxjqZxLGxTPOlA
rBjivbEYKdCSp+T3MOz+2tQ160jTg9wAO4Rq/KRT0hxVr+ABGSJGRUcQgNXdvofe
Q73iZqiSFTlGPQr0CAFT78tK8cb2mv9b583SeLTgAcZ/wxZP7NA=
=9BMa
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.12-1' of gitolite.kernel.org:pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.12-1
* Enable pin control on Intel Alder Lake-P
* Traverse through capabilities, convert them to features for the future use
The following is an automated git shortlog grouped by driver:
intel:
- Convert capability list to features
- Drop unnecessary check for predefined features
- Split intel_pinctrl_add_padgroups() for better maintenance
tigerlake:
- Add Alder Lake-P ACPI ID
Add the function selector to the pinmux-functions debugfs output. This
is an integer which is the index into the pinmux function tree. It will
make it easier to correlate function name to function selector without
having to count the lines in the output.
Example output of "pinmux-functions":
function 0: pinmux-uart0-pins, groups = [ pinmux-uart0-pins ]
function 1: pinmux-uart1-pins, groups = [ pinmux-uart1-pins ]
function 2: pinmux-uart2-pins, groups = [ pinmux-uart2-pins ]
function 3: pinmux-mmc0-pins, groups = [ pinmux-mmc0-pins ]
function 3: pinmux-mmc1-pins, groups = [ pinmux-mmc1-pins ]
function 5: pinmux-i2c0-pins, groups = [ pinmux-i2c0-pins ]
function 6: pinmux-i2c1-pins, groups = [ pinmux-i2c1-pins ]
function 7: pinmux-i2c2-pins, groups = [ pinmux-i2c2-pins ]
function 8: pinmux-pwm0-pins, groups = [ pinmux-pwm0-pins ]
function 9: pinmux-pwm1-pins, groups = [ pinmux-pwm1-pins ]
function 10: pinmux-adc-pins, groups = [ pinmux-adc-pins ]
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Robert Nelson <robertcnelson@beagleboard.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Link: https://lore.kernel.org/r/20210123202212.528046-1-drew@beagleboard.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch converts spin_[lock|unlock] functions of pin bank to
raw_spinlock to support preempt-rt. This can avoid BUG() assertion when
irqchip callbacks are triggerred. Spinlocks can be converted rt_mutex
which is preemptible when we apply preempt-rt patches.
According to "Documentation/driver-api/gpio/driver.rst",
"Realtime considerations: a realtime compliant GPIO driver should not
use spinlock_t or any sleepable APIs (like PM runtime) as part of its
irqchip implementation.
- spinlock_t should be replaced with raw_spinlock_t.[1]
"
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210121030009.25673-1-chanho61.park@samsung.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Actions Semi pinctrl drivers are a mix of both ARM32 and ARM64
platforms. So let's add the correct platform dependency to avoid them
being selected on the other.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210121062547.27173-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are only two pins left now, used to connect to the PMIC via I2C.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210118020848.11721-6-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Port A is used for an internal connection to some analogue circuitry
which looks like an AC200 IP (as in the H6), though this is not
mentioned in the manual.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20210118020848.11721-5-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add otg function and otg-vbus group.
- Add lcd-8bit, lcd-16bit, lcd-18bit, lcd-generic and lcd-special
groups. Change the lcd-24bit group so that it only selects the pins
that aren't in the lcd-18bit and lcd-generic groups (which breaks
Device Tree in theory, but there is none out there for any JZ4760
based board, yet). Remove the lcd-no-pins group which is just useless.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210120110722.20133-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ST-Ericsson U300 platform is getting removed, so this driver is no
longer needed.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120132045.2127659-6-arnd@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ST-Ericsson U300 platform is getting removed, so this driver is no
longer needed.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120132045.2127659-5-arnd@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120132045.2127659-4-arnd@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120132045.2127659-3-arnd@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested on a JZ4740 system (ARCH=mips make qi_lb60_defconfig), this saves
about 14 KiB, by allowing the compiler to garbage-collect all the
functions and tables that correspond to SoCs that were disabled in the
config.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201213235447.138271-2-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Restrict debug runtime-checks to Renesas platforms,
- Initial support for the R-Car V3U SoC.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYAFgRQAKCRCKwlD9ZEnx
cEWIAP40TrUerqfnQgJ7iNYLh9WfSk48w9Gxzm92E7FanXaJBAD/dmkieXwQBBig
zKNuoWL2ZlK7O5MMkzpNnhLNS95SEQs=
=vIxg
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.12-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.12
- Restrict debug runtime-checks to Renesas platforms,
- Initial support for the R-Car V3U SoC.
Fix the following coccicheck warning:
./drivers/pinctrl/sprd/pinctrl-sprd.c:690:8-23: WARNING: Comparison to
bool
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: YANG LI <abaci-bugfix@linux.alibaba.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/1610440080-68600-1-git-send-email-abaci-bugfix@linux.alibaba.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pins, groups and functions for the 16-Bit Timer Pulse Unit outputs
on the R-Car R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210112165929.31002-13-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and function for the Interrupt Controller for External
Devices (INTC-EX) on the R-Car R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210112165929.31002-7-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds HSCIF0-3 pins, groups and functions to the R8A779A0
(V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165929.31002-6-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds groups and function for AVB PHY, LINK, MAGIC, RGMII and
PTP pins for the R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165929.31002-3-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C0-6 pins, groups and functions to the R8A779A0 (V3U)
SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165929.31002-2-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds SCIF0, 1, 3 and 4 pins, groups and functions for the
R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165912.30876-6-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds initial pinctrl support for the R8A779A0 (V3U) SoC,
including bias, drive strength and voltage control.
Based on patch by LUU HOAI <hoai.luu.ub@renesas.com>.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165912.30876-5-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds config macros describing the voltage levels available on
a pin. The current default (3.3V/1.8V) maps to zero to avoid having to
change existing PFC implementations.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165912.30876-3-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The V3U SoC has several unlock registers, one per register group. They
reside at offset zero in each 0x200 bytes-sized block.
To avoid adding yet another table to the PFC implementation, this
patch adds the option to specify an address mask instead of the fixed
address in sh_pfc_soc_info::unlock_reg.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165912.30876-2-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When DEBUG is defined (e.g. if CONFIG_DEBUG_PINCTRL=y), the Renesas pin
control driver runs sanity checks against the pin control tables. This
may cause lots of output on the console, and can be annoying in ARM
multi-platform kernels. Fix this by only running the checks when
running on SuperH, or on a DT platform supported by the Renesas pin
controller driver.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210111165013.496897-1-geert+renesas@glider.be
Intel Alder Lake-P PCH has the same GPIO hardware than Tiger Lake-LP
PCH but the ACPI ID is different. Add this new ACPI ID to the list of
supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Communities can have features provided in the capability list.
Traverse the list and convert to respective features.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
None of the drivers is overriding features. Remove unnecessary check.
While here, rename rev to value to make easier further development.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently the intel_pinctrl_add_padgroups() is twisted a bit due to
a different nature of the pin control hardware implementations. Thus,
its maintenance is a bit hard. Besides that some pieces of code
are run on all hardware and make this code slightly inefficient,
and moreover, validation for one case is done in a wrong time in a flow
which makes it even slower.
Split intel_pinctrl_add_padgroups() to two functions, one per hardware
implementation, for better maintenance and readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
As there is an RSB controller in the H6 SoC, there should be some pin
configuration for it. While no such configuration is documented, the
"s_i2c" pins are suspiciously on the "alternate" function 3, with no
primary function 2 given. This suggests the primary function for these
pins is actually RSB, and that is indeed the case.
Add the "s_rsb" pin functions so the RSB controller can be used.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20210103100007.32867-3-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove all empty lines at the end of functions in pinctrl subsystem,
and make the code neat.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Zhaoyu Liu <zackaryliu@yeah.net>
Link: https://lore.kernel.org/r/X98NP6NFK1Afzrgd@manjaro
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kernel test robot reported the following warning:
'warning: no previous prototype for 'rt2880_pinmux_init''.
This function is the entry point for the platform driver and
it is private to this driver. Hence declare it 'static' which is
the correct thing to do fixing also this warning.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20201228064727.30098-1-sergio.paracuellos@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some paths in probe function are returning '-EINVAL'
instead of preserve original code from called functions.
Change them to preserve all of them.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201213161721.6514-7-sergio.paracuellos@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
