The hw now refers to two new blocks:
* rx tr tail - The Tail index on the free buffers queue TR,
which is update by the device after reading the free buffer
from the tr.
* rx cr tail - Updated by the driver when completing
processing a new completion descriptor in the cr.
Add these two new struct to the rxq, allocate and free them
when needed.
In addition, the register for rx write pointer had been changed
to HBUS_TARG_WRPTR. The way to differentiate tx from rx is the
queue number. TX range is 0-511, and RX's is 512-527.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for the new 22560 family of devices and, while at it,
reorganize the 22000 family so it fits better with the new one.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new device IDs for the 9000 series.
Cc: stable@vger.kernel.org # 4.14
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbD/3rAAoJEG4XJFUm622b1ZwH/1xe1IqcwJXzfoDsYPlXVnSh
TiLExjKkD0ty5M0//844FxpxE1sSYJKOJ11uz/COzyG2qi4+5lgpUdjnDoINuKfH
ycqrXGssW7ogPWkVvnxKtlEYvkHNRYLQtxvd26umT77C69jVJLD0x9uihhh2En/C
EKs+OK1Pp0SRvTfB4AblWzoAnpEe1wHJFFh4i3F5H0lMGxLQz/YjFl5aeAjjR406
0vSKLGy2wKIydp8Pe4cAqBEeUWDJurn8ufkk7bmAET5zaXTH1qgZzLH3OWtx/ksz
mcPQq9/ctv35G2917t3Sn69SIUCDGfYkP5DiZV+ti0Hz2gIV0zOg7mGYCU8uHaU=
=11X5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.18
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the rx_allocator worker is canceled before running the
rx_init routine. rx_init frees and re-allocates all rxb's pages. The
rx_allocator worker also allocates pages for the used rxb's. Running
rx_init and rx_allocator simultaniously causes a kernel panic. Fix
that by canceling the work in rx_init.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Recently we have switched the csr addresses and values configuration
from a single configuration to all devices to a per-device configuration.
Doing that, the configuration for 6300 devices wasn't set.
This missing definition introduced a kernel panic once trying to access
the csr's.
Add the missing 6300 csr configuration.
While at it, add a checker that the csr values were indeed
configured, and bail out more gracefully if not.
Fixes: a8cbb46f83 ("iwlwifi: allow different csr flags for different device families")
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When there are 16 or more logical CPUs, we request for
`IWL_MAX_RX_HW_QUEUES` (16) IRQs only as we limit to that number of
IRQs, but later on we compare the number of IRQs returned to
nr_online_cpus+2 instead of max_irqs, the latter being what we
actually asked for. This ends up setting num_rx_queues to 17 which
causes lots of out-of-bounds array accesses later on.
Compare to max_irqs instead, and also add an assertion in case
num_rx_queues > IWM_MAX_RX_HW_QUEUES.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=199551
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Hao Wei Tee <angelsl@in04.sg>
Tested-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we fail to to grab NIC access because the device is not responding
(i.e. CSR_GP_CNTRL returns 0xFFFFFFFF), remove the device from the PCI
bus, to avoid any further damage, and to let the user space rescan.
In order to inform the userspace that a rescan is needed, we send a
kobject uevent with "INACCESSIBLE".
This functionality is disabled by default, but can be enabled via a
new module parameter called "remove_when_gone". In the future we may
change this module parameter to include 3 modes instead: do nothing;
auto-rescan or; send uevent.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
In case of A-MSDUs, the trans layer is taking care of building
the subframes (out of the given skb), according to the given gso_size.
However, in some testing flows, we want to build the whole A-MSDU
frame in a different place (e.g. userspace), and ask the driver
to send it as-is.
In case of gso_size==0, simply treat the frame as normal-frame,
although the A-MSDU flag is set.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Different device families may have different flag values
for passing a message to the fw (i.e. SW_RESET).
In order to keep the code readable, and avoid conditioning
upon the family, store a value for each flag, which indicates
the bit that needs to be enabled.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avoid a race where two (or more) commands get the
same index:
1. T1 calls enqueue_hcmd and the local TFD index is assigned to
txq->write_ptr;
2. Context switch 'before incrementing txq->write_ptr';
3. T2 calls enqueue_hcmd and the local TFD index is assigned to
txq->write_ptr;
4. Now the index is set to the same value for both commands of T1 and
T2.
To prevent this from happening, set the local TFD index inside the
critical section (the index is set by global txq write pointer).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Op mode will begin tp use varying size of TX queue.
All the infra is in place, allow it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As preparation for dynamic queue sizing, add a parameter
of the TX queue size to the dynamic queue allocation op
mode API.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts commit dd05f9aab4.
Shorter TX queues support was added eventually without the
need for the parameters this patch added.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When support for shorter TX queues was introduced, it
didn't include the actual allocation of shorter queue,
which is the main motive for the change.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we enable TSO, we can have a lot of packets in the
operation mode that will be pushed to the transport
no matter what is the queue's fullness state.
To cope with that the transport can buffer those packets
and add them to the ring later when there is more room.
This implementation was missing in the Gen2 devices'
code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A lot of new PCI IDs were added for the 9000 series. Add them to the
list of supported PCI IDs.
Cc: stable@vger.kernel.org # 4.13+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some devices use a shared clock which is very sensitive to variations
and cause trouble in some situations. We need to set a bit in the phy
configuration to indicate that to the FW. To make this generic, add a
extra_phy_config_flags element to the device configuration and OR it
into the phy_cfg before sending it to the firmware. And also create a
set of configurations for devices that use shared clocks and need this
extra bit to be set.
Fixes: c62446d2b0 ("iwlwifi: add new 9460 series PCI IDs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our Transmit Frame Descriptor (TFD) is a DMA descriptor that
includes several pointers to be able to transmit a packet
which is not physically contiguous.
Depending on the hardware being use, we can have 20 or 25
pointers in a single TFD. In both cases, it is more than
enough and it is quite hard to hit this limit.
It has been reported that when using specific applications
(Ktorrent), we can actually use all the pointers and then
a long standing bug showed up.
When we free the TFD, we check its number of valid pointers
and make sure it doesn't exceed the number of pointers the
hardware support.
This check had an off by one bug: it is perfectly valid to
free the 20 pointers if the TFD has 20 pointers.
Fix that.
https://bugzilla.kernel.org/show_bug.cgi?id=197981
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Here are patches which have been accumulating over the holidays and
after the New Year. Business as usual and nothing special really
standing out.
But what's noteworthy here is that Larry Finger is stepping down as
the rtlwifi maintainer. He has been maintaining rtlwifi since it was
applied back in 2010 in commit 0c8173385e ("rtl8192ce: Add new
driver") and it has been no easy role trying to juggle between the
vendor, demanding upstream community and users. So big thank you to
Larry for all his efforts!
ath10k
* more preparation work for wcn3990 support
* add memory dump to firmware coredump files
wil6210
* support scheduled scan
* support 40-bit DMA addresses
qtnfmac
* support MAC address based access control
* support for radar detection and Channel Availibility Check (CAC)
mwifiex
* firmware coredump for usb devices
rtlwifi
* Larry Finger steps down as the maintainer and Ping-Ke Shih becomes
the new maintainer
* add debugfs interfaces to dump register and btcoex status, and also
write registers and h2c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaWd2WAAoJEG4XJFUm622bDnsH/2+Y5MEn31xvv7FGP46dHCNB
wk1SgcQOQdb7taIpZ++tFvhTQOXwrtGMA5iAFLeg9+07tqGIaZQqr58aab7BCQTi
2PgUK9sEdI5LPw3KmhnaqfHMVDKMaYdjcAhLG4FzJqMoDfTuPr56Vnnde3J2A0mj
hhFRarNKBArEvRaWtNypdZQN8HM10v3LJq+HNnK/yep7fW2EuwSwTO2YBqDhrwAD
0gzfV6yi05497uVv6W+5CKRawu7RoYgbFTaEa8rmCViIjf9bK4gPdsW18a/DTNMz
MfvLF2RQZk1k944+a+a983oqZNkq9dEWd0kF0CSFgbO3r/SO7264yc4PHpZKy/s=
=2eQ4
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
Here are patches which have been accumulating over the holidays and
after the New Year. Business as usual and nothing special really
standing out.
But what's noteworthy here is that Larry Finger is stepping down as
the rtlwifi maintainer. He has been maintaining rtlwifi since it was
applied back in 2010 in commit 0c8173385e ("rtl8192ce: Add new
driver") and it has been no easy role trying to juggle between the
vendor, demanding upstream community and users. So big thank you to
Larry for all his efforts!
ath10k
* more preparation work for wcn3990 support
* add memory dump to firmware coredump files
wil6210
* support scheduled scan
* support 40-bit DMA addresses
qtnfmac
* support MAC address based access control
* support for radar detection and Channel Availibility Check (CAC)
mwifiex
* firmware coredump for usb devices
rtlwifi
* Larry Finger steps down as the maintainer and Ping-Ke Shih becomes
the new maintainer
* add debugfs interfaces to dump register and btcoex status, and also
write registers and h2c
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF alignment tests got a conflict because the registers
are output as Rn_w instead of just Rn in net-next, and
in net a fixup for a testcase prohibits logical operations
on pointers before using them.
Also, we should attempt to patch BPF call args if JIT always on is
enabled. Instead, if we fail to JIT the subprogs we should pass
an error back up and fail immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
22000 devices (previously referenced as A000) can support
short transmit queues. This means that we have less DMA
descriptors (TFD) for those shorter queues.
Previous devices must still have 256 TFDs for each queue
even if those 256 TFDs point to fewer buffers.
When I introduced support for the short queues for 22000
I broke older devices by assuming that they can also have
less TFDs in their queues. This led to several problems:
1) the payload of the commands weren't unmapped properly
which caused the SWIOTLB to complain at some point.
2) the hardware could get confused and we get hardware
crashes.
The corresponding bugzilla entries are:
https://bugzilla.kernel.org/show_bug.cgi?id=198201https://bugzilla.kernel.org/show_bug.cgi?id=198265
Cc: stable@vger.kernel.org # 4.14+
Fixes: 4ecab56160 ("iwlwifi: pcie: support short Tx queues for A000 device family")
Reviewed-by: Sharon, Sara <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Most of the sw resets in the code are done by one function,
which writes to the relevant CSR.
Use the common function to perform the only reset which was
done separately, redundant to the common code.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support internal debug data collection on 9000 and newer
devices.
The method for finding the base and end address has changed
on new HW's, so introduce a new version of debug destination
tlv.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaN8MiAAoJEG4XJFUm622bGN4H/jc7+JqGUMozK8CKe5UGFnu7
HlwP3Vpz7SR655CgoMzvNzJ6lvBxaPA77epPFkALuwua3J22feakv5UGipT7RPI/
EtFCtq6+dIB+qooJ/8hUQVfAV8o13+dQzBQqtp7Wg37ok0qhcGpTLsvf2rI0ZG1R
+lcC2Jyk0lYjAPuPri3+KjxPLkZhGbx/hCdKwxQfCoubEVoqimMcQ68+RqU3rxNB
Of2Sk8IsaIevantLPnmO0+9OhZiMyoy4QGSnnuHntdpgZqEl0NbmVshQONCU9oTu
3RPKvbbYe57gRfgLKEvqTvij5R8ZxxwF+BFacaXch7Q9k6pMoJuyD6gJ8/S8AW8=
=FTCb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
The drivers/net/wireless/intel/iwlwifi/pcie/drv.c conflict was
resolved using a diff provided by Kalle in his pull request.
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
add 1 PCI ID for 9260 series and 1 for 22000 series.
Cc: stable@vger.kernel.org
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Rename the temporary name A000 to 22000;
* Change in the way we print the firmware version;
* Remove some unused code;
* Other small improvements;
-----BEGIN PGP SIGNATURE-----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=j1dk
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi updates for v4.16
* Rename the temporary name A000 to 22000;
* Change in the way we print the firmware version;
* Remove some unused code;
* Other small improvements;
kvalo:
There were conflicts, I fixed them with taking into account commit c2c48ddfc8
("iwlwifi: fix firmware names for 9000 and A000 series hw"):
CONFLICT (content): Merge conflict in drivers/net/wireless/intel/iwlwifi/iwl-config.h
CONFLICT (modify/delete): drivers/net/wireless/intel/iwlwifi/cfg/a000.c deleted in ca495785063c428641cc6df8888afd2587ca6677 and modified in HEAD. Version HEAD of drivers/net/wireless/intel/iwlwifi/cfg/a000.c left in tree.
* One fix in rate-scaling;
* One fix for the TX queue hang detection for AP/GO modes;
* Fix the TX queue hang timeout used in monitor interfaces;
* Fix packet injection;
* Remove a wrong error message when dumping PCI registers;
* Fix race condition with RF-kill;
-----BEGIN PGP SIGNATURE-----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=eD7A
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-11-28' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Second batch of fixes intended for 4.15.
* One fix in rate-scaling;
* One fix for the TX queue hang detection for AP/GO modes;
* Fix the TX queue hang timeout used in monitor interfaces;
* Fix packet injection;
* Remove a wrong error message when dumping PCI registers;
* Fix race condition with RF-kill;
The family name A000 was just a place-holder when we didn't know what
the official name would be yet. Now we know that the family name is
22000, so rename all occurrences accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull timer updates from Thomas Gleixner:
- The final conversion of timer wheel timers to timer_setup().
A few manual conversions and a large coccinelle assisted sweep and
the removal of the old initialization mechanisms and the related
code.
- Remove the now unused VSYSCALL update code
- Fix permissions of /proc/timer_list. I still need to get rid of that
file completely
- Rename a misnomed clocksource function and remove a stale declaration
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
m68k/macboing: Fix missed timer callback assignment
treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
timer: Remove redundant __setup_timer*() macros
timer: Pass function down to initialization routines
timer: Remove unused data arguments from macros
timer: Switch callback prototype to take struct timer_list * argument
timer: Pass timer_list pointer to callbacks unconditionally
Coccinelle: Remove setup_timer.cocci
timer: Remove setup_*timer() interface
timer: Remove init_timer() interface
treewide: setup_timer() -> timer_setup() (2 field)
treewide: setup_timer() -> timer_setup()
treewide: init_timer() -> setup_timer()
treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
s390: cmm: Convert timers to use timer_setup()
lightnvm: Convert timers to use timer_setup()
drivers/net: cris: Convert timers to use timer_setup()
drm/vc4: Convert timers to use timer_setup()
block/laptop_mode: Convert timers to use timer_setup()
net/atm/mpc: Avoid open-coded assignment of timer callback function
...
When getting HW rfkill we get stop_device being called from
two paths.
One path is the IRQ calling stop device, and updating op
mode and stack.
As a result, cfg80211 is running rfkill sync work that shuts
down all devices (second path).
In the second path, we eventually get to iwl_mvm_stop_device
which calls iwl_fw_dump_conf_clear->iwl_fw_dbg_stop_recording,
that access periphery registers.
The device may be stopped at this point from the first path,
which will result with a failure to access those registers.
Simply checking for the trans status is insufficient, since
the race will still exist, only minimized.
Instead, move the stop from iwl_fw_dump_conf_clear (which is
getting called only from stop path) to the transport stop
device function, where the access is always safe.
This has the added value, of actually stopping dbgc before
stopping device even when the stop is initiated from the
transport.
Fixes: 1efc3843a4 ("iwlwifi: stop dbgc recording before stopping DMA")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Current pci dumping code code is always falling to the error
path, resulting with a constant "Read failed" message, also
for the successful reads.
Fixes: a5c932e41fdd ("iwlwifi: pcie: dump registers when HW becomes inaccessible")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
-----BEGIN PGP SIGNATURE-----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=JPn9
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-11-19' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
iwlwifi: first set of fixes for 4.15
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
A lot of PCI IDs were missing and there were some problems with the
configuration and firmware selection for devices on the 9000 series.
Fix the firmware selection by adding files for the B-steps; add
configuration for some integrated devices; and add a bunch of PCI IDs
(mostly for integrated devices) that were missing from the driver's
list.
Without this patch, a lot of devices will not be recognized or will
try to load the wrong firmware file.
Cc: stable@vger.kernel.org # 4.13
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Commit a6d24fad00 ("iwlwifi: pcie: dump registers when HW becomes
inaccessible") added a function to dump pcie config registers and
memory mapped registers on a failure. It is currently only accessible
within trans.c. Add it to struct iwl_trans_ops, so that failure cases
in other files can call it. While there, add a call to this function
from iwl_pcie_load_firmware_chunk in pcie/tx.c, since this is a common
failure case seen on some platforms.
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
[modified the commit message slightly]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This variable is never used, so remove the code to set it.
After this, the variable 'iph' also has the same fate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's hard to find values that are missing in the list, so sorting the
values and comparing them makes it much easier. To simplify this
task, sort the devices in the list.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The default power limit read from the SPLC method in ACPI doesn't
have anything to do with the transport and is only used in the opmode,
so we can remove it from the trans. Additionally, this value is only
user when the opmode is starting, so we don't need to store it
anywhere.
Remove the dflt_pwr_limit element from the trans and move call to
iwl_acpi_get_pwr_limit() call to mvm.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move most of the set_dflt_pwr_limit() function to acpi.c and make it
return the pwr_limit value instead of setting directly. Also rename
it to iwl_acpi_get_pwr_limit().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of finding the wifi package with its own code, we can reuse
the new iwl_acpi_get_wifi_pkg() function when reading the default
power limit from SPLC.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of defining each method where they are used and re-defining
WIFI_DOMAIN in each one of them, move all the definitions to a central
place and define the domain only a single time.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are many places where the same process of invoking a method from
ACPI is used, causing a lot of duplicate code. To improve this,
introduce a new function to get an ACPI object by invoking an ACPI
method that can be reused.
Additionally, since this function needs to be called when we only have
the trans, the opmode or the device, introduce a new debug macro that
gets the device as a parameter so it can be used in the new function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We conclude the HW became inaccessible when we timeout waiting for
a bit to be set in a memory mapped register (CSR_GP_CNTRL). This
conclusion may not be true because the bit may not get set due to:
- a firmware issue
- a driver issue
- a PCI bus issue
- a platform issue
There are a lot of such reports with really no good debug information
beyond this message to help us.
Add some debug information and attempt to dump the different register
spaces at such a failure:
* Dump some configuration space of device - this will tell us if
something very basic is broken in the PCIe bus (so that configuration
accesses are failing). If this works, the PCIe bus seems OK. If this
does not work, it is definitely an PCIe issue.
* Dump some memory mapped registers - if we're reading some sane'ish
values, this will tell us that the PCIe bus is OK, but may be a firmware
/ driver issue. If this does not work, it may be a PCI configuration
issue or a driver/firmware issue.
* Dump parent and device's AER registers, will give us some straws to
chew on.
This is the sample output:
[ 13.082651] ------------[ cut here ]------------
[ 13.086791] iwlwifi 0000:01:00.0: iwlwifi transaction failed, dumping registers
[ 13.086793] iwlwifi 0000:01:00.0: iwlwifi device config registers:
[ 13.086893] iwlwifi 0000:01:00.0: 00000000: 095a8086 00100406 02800059 00000000 00000004 00000000 00000000 00000000
[ 13.086895] iwlwifi 0000:01:00.0: 00000020: 00000000 00000000 00000000 50108086 00000000 000000c8 00000000 00000100
[ 13.086901] iwlwifi 0000:01:00.0: iwlwifi device memory mapped registers:
[ 13.086989] iwlwifi 0000:01:00.0: 00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 13.086991] iwlwifi 0000:01:00.0: 00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 13.086999] iwlwifi 0000:01:00.0: iwlwifi device AER capability structure:
[ 13.087033] iwlwifi 0000:01:00.0: 00000000: 14010001 00100000 00000000 00462031 00002000 00002000 00000014 40000001
[ 13.087034] iwlwifi 0000:01:00.0: 00000020: 0000000f d140000c 00000000
[ 13.087036] iwlwifi 0000:01:00.0: iwlwifi parent port (0000:00:1c.0) config registers:
[ 13.087074] iwlwifi 0000:00:1c.0: 00000000: 9d108086 00100506 060400f1 00810010 00000000 00000000 00010100 200000f0
[ 13.087075] iwlwifi 0000:00:1c.0: 00000020: d140d140 0001fff1 00000000 00000000 00000000 00000040 00000000 0006010b
[ 13.087087] ------------[ cut here ]------------
[ 13.087095] WARNING: CPU: 0 PID: 1759 at drivers/net/wireless/iwl7000/iwlwifi/pcie/trans.c:2082 iwl_trans_pcie_reclaim+0x1ee4/0x2b9a [iwlwifi]()
[ 13.087096] Timeout waiting for hardware access (CSR_GP_CNTRL 0xffffffff)
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Devices in the A000 family can use a different size for the command queue.
To allow this, make the command queue size configurable and set the size
for A000 devices to 32.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new a000 device with PCI ID (0x2720, 0x0030).
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The PCI ID (0x2720, 0x0070) was set with the config struct
iwla000_2ax_cfg_hr instead of iwla000_2ac_cfg_hr_cdb.
Fixes: 175b87c692 ("iwlwifi: add the new a000_2ax series")
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Work queues cannot be allocated when a mutex is held because the mutex
may be in use and that would make it sleep. Doing so generates the
following splat with 4.13+:
[ 19.513298] ======================================================
[ 19.513429] WARNING: possible circular locking dependency detected
[ 19.513557] 4.13.0-rc5+ #6 Not tainted
[ 19.513638] ------------------------------------------------------
[ 19.513767] cpuhp/0/12 is trying to acquire lock:
[ 19.513867] (&tz->lock){+.+.+.}, at: [<ffffffff924afebb>] thermal_zone_get_temp+0x5b/0xb0
[ 19.514047]
[ 19.514047] but task is already holding lock:
[ 19.514166] (cpuhp_state){+.+.+.}, at: [<ffffffff91cc4baa>] cpuhp_thread_fun+0x3a/0x210
[ 19.514338]
[ 19.514338] which lock already depends on the new lock.
This lock dependency already existed with previous kernel versions,
but it was not detected until commit 49dfe2a677 ("cpuhotplug: Link
lock stacks for hotplug callbacks") was introduced.
Reported-by: David Weinehall <david.weinehall@intel.com>
Reported-by: Jiri Kosina <jikos@kernel.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Stephen Rothwell reported quite a few conflicts in iwlwifi between
wireless-drivers and wireless-drivers-next. To avoid any problems later in
other trees merge w-d to w-d-next to fix those conflicts early.
Newer versions of A000 devices come with two diffenent RF modules.
The PCI_ID, the subsystem ID and the RF ID are identical in these two cases,
so we need to differentiate them by using the CSR_HW_RF_ID register-
in order to load the appropriate firmware.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This allows to modify TFD_TX_CMD_SLOTS to a power of 2
which is smaller than 256.
Note that we still need to set values to wrap at 256
into the scheduler's write pointer, but all the rest of
the code can use shorter transmit queues.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we unmap a non-empty Tx queue, we need to free the
pages that we allocated for the headers in TSO flows.
This code existed for the 9000 device family, but somehow
it got left out when the new Tx path for the A000 devices
was written.
Fixes: 2b0c5946d9ed ("iwlwifi: pcie: introduce a000 TX queues management")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are still some references to 3945 and 4965 HW, which were never
supported in iwlwifi. These references were inherited from a previous
project and are irrelevant here. Additionally, remove some irrelevant
references to 5100 HW. Remove all these.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The TVQM tells us the initial write pointer for a queue,
but that write pointer is in WiFi sequence number unit
and not in TFD index unit. Which means that the write
pointer in the TVQM's response can be bigger than the
Tx queue ring size.
Fix that by modulo'ing the write pointer from the TVQM
with the Tx queue size.
Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Load FW according to NIC type,
taking into account simulation, if exists.
This is determined by a prph register.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZiHuQAAoJEG4XJFUm622bVSEIAKdausycC6OOZjwTGWnFyxE/
58n79VTrTbXVLwJ7lSBCGYCTujc7amPxAVlDOLYd+9TKm0fO7gap50Gdl35HO5sp
9v/augHQSouz52q2vgsTi0JbXsqhJQZ4Ie4P0fo8OyqJMYAvFga2FhFBpJseMYd9
NX88SMoxAGgDkTC0JfzzLnA/jZ0W6ULai6zmRE1s6lUIynP2kzHgpfbMH3+KEkod
SUW+yX91MdOkkyFGXyY11uuBqanUpEVSAQXW6J76vw3qS88qIqaL3iIeJ6C4Vozq
fKNkHN4iZOd9FlKY1IFi4vS0+7hWiq6DQ3c+ngtU6cuq1XdBa6PuanC3I2e0B8E=
=PKUU
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename this function to the more appropriate iwl_pcie_check_hw_rf_kill()
since it's only a function in the pcie code and cannot be called from
any other place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The return status check of iwl_pcie_gen2_build_amsdu
was buggy. Fix it.
Fixes: 6ffe5de35b ("iwlwifi: pcie: add AMSDU to gen2")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Apart from DVM, all firmware uses the same base API, and there's
code outside iwlmvm that needs to interact with it. Reflect this
in the source better and reorganize the firmware API to a new
fw/api/ directory.
While at it, split the already pretty large fw-api.h file into a
number of smaller files, going from almost 3k lines in there to
a maximum number of lines less than 1k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add two PCI IDs for the 9160 series.
Add five PCI IDs for the 9260 series.
Add one PCI IDs for the 9270 series.
Add seven PCI IDs for the 9460 series.
Add five PCI IDs for the 9560 series.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't set the error code here so we end up returning ERR_PTR(0) which
is NULL. The caller doesn't expect that so it results in a NULL
dereference.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Before TVQM, all TX queues were allocated straight at init.
With TVQM, queues are allocated on demand and hence we need
to check if a queue exists before dereferencing it.
Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The newest devices need a longer time to reset because of
their more complex hardware. Wait 5ms after device reset.
Consolidate all the places that reset the device in the
PCIe transport to avoid future bugs.
While at it, unify the flow to use set_bit instead of full
write as requested by the hardware designers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_pcie_apm_init can fail so make sure that the caller
takes the status into account.
Also, ensure that the error that iwl_pcie_apm_init can emit
will appear in the kernel log by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When going into suspend, the HW configuration for MSI-X will
likely be lost. As a consequence, after waking up, all IRQ
causes will be mapped to interrupt 0, and as a consequence we
don't notice the interrupt because in most cases this is an
interrupt for a queue, and getting it doesn't read the other
cause registers.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have tracing for both pre-ICT and ICT interrupts, including all
the data read there. Extend the tracing to MSI-X interrupts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's a lot of mvm code that really should be more generic
and part of the iwlwifi module. Start by making a place to
keep such code - in the new "fw" subdirectory - and already
move the firmware related header files there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This appears to happen in some cases, like when iwlmvm is unloaded and
loaded again without also unloading iwlwifi. Warn in this case and free
the paging data to be able to continue without causing corruption and
kernel crashes due to it (otherwise, paging data is overwritten, but
dram->paging_cnt gets to be twice as big as it should be, and then an
eventual free will crash.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
By setting the pointers to NULL at the end, these functions
are made idempotent.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Where possible (all except for "11n_disable", which isn't valid in C)
rename the internal names for module parameters to be the same as the
externally visible names, to aid finding their use etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Print the queue for the existing debug message and add a new
debug message indicating where the RB ended.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Print out both queue IDs to be able to see what went wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new config struct for the new a000 2ax series and add
the five PCI ID for it.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A hardware issue on 9000 series devices sometimes causes RF-kill
interrupts to not be propagated to the host properly if ASPM is
enabled. Work around this by setting the right hardware bit to
allow it to interrupt the host for this reason (rfkill).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to a hardware issue, certain power saving had to be
disabled. However, this issue was fixed in B-step, so the
workaround only needs to apply to A-step.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Some changes in suspend/resume handling to support new FWs;
* A bunch of RF-kill related fixes;
* Continued work towards the A000 family;
* Support for a new version of the TX flush FW API;
* Some fixes in monitor interfaces;
* A few fixes in the recovery flows;
* Johannes' documentation fixes and FW API struct cleanups continue;
* Remove some noise from the kernel logs;
* Some other small improvements, fixes and cleanups;
-----BEGIN PGP SIGNATURE-----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=DdqX
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
More iwlwifi patches for 4.13
* Some changes in suspend/resume handling to support new FWs;
* A bunch of RF-kill related fixes;
* Continued work towards the A000 family;
* Support for a new version of the TX flush FW API;
* Some fixes in monitor interfaces;
* A few fixes in the recovery flows;
* Johannes' documentation fixes and FW API struct cleanups continue;
* Remove some noise from the kernel logs;
* Some other small improvements, fixes and cleanups;
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZT/ROAAoJEG4XJFUm622b/IwH+wQtBXP+P57DZ97BdETcZ3Wd
ejm9KKT3IxcP7kzItT9UR1zv7LNx4NgSkJMfhf37jJ1WIuE2fp/ctNv6mz3PvohW
jD1fLynwEMMC7PLHEy5+xGtL61KYc2mtXs/bfLFl94hZUiaocrsBDIT4fXoyIWif
y3MUlBKDbHA27ULRd485C0MRekRSvR/rq6iST4KsIsa8RflJbdH64teTEnQPp4kh
nvhfnaxVEqHK7mYbarC58yYLNOU8gfQXmeeTfd6jhCXRjfEw37IvtNC8BT4B9ZDX
YMZLbkeDSwNGXIH7EIrpGOYHCPh+qsiJ+sx7YodomcJvd1nVrmbuZZt9/EqWXuY=
=Fd/c
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In some platforms, having the device enabled with certain radio
frontends causes the platform to not be able to resume properly
from suspend, regardless of the wakeup cause. This was traced to
a hardware issue with the integrated 9000-series A-step variant.
Set the right hardware bit to disable the problematic state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware crashes, the transmit queues can't make
any progress. This is why we stop the counter that monitor
the transmit queues' activity.
The call that notifies the error to the op_mode may take
a bit of time, so stop the timer of the transmit queues
earlier.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver prints "L1 Enabled - LTR Enabled" all the time as dev_info,
which is just useless noise in most cases. Convert this to
IWL_DEBUG_POWER() so we don't pollute the log unnecessarily but still
can get this info on demand.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Nothing ever checks the return value of iwl_pcie_apm_stop_master(),
so there's no point in it having one - make it return void.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case we need to move the scheduler write pointer by
steps of 0x40, 0x80 or 0xc0, the scheduler gets stuck.
This leads to hardware error interrupts with status:
0x5A5A5A5A or alike.
In order to work around this, detect in the transport
layer that we are going to hit this case and tell iwlmvm
to increment the sequence number of the packets. This
allows to keep the requirement that the WiFi sequence
number is in sync with the index in the scheduler Tx queue
and it also allows to avoid the problematic sequence.
This means that from time to time, we will start a queue
from ssn + 1, but that shouldn't be a problem since we
don't switch to new queues for AMPDU now that we have
DQA which allows to keep the same queue while toggling
the AMPDU state.
This bug has been fixed on 9000 devices and up.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we started using threaded irqs, all the opmode calls were changed
to be called with local_bh disabled. The reason for this was it was
that mac80211 needs that. When we are handling FW errors, mac80211 is
not involved, so we don't need it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the command name is printed on command completion, the wrong
group is used, leading to the wrong name being printed. Fix this
by using the group ID without inappropriately mangling it through
iwl_cmd_groupid() - it's already a u8. Also, while at it, use it
from the same place as the command ID, everything else is just
confusing.
Fixes: ab02165cce ("iwlwifi: add wide firmware command infrastructure for TX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending non-linear SKBs that should be included in the regular
TX tracing completely (and not be pushed into the tx_data tracing),
the (tracing) code didn't correctly take the fact that they were
non-linear into account and added only the skb head portion.
This probably never really triggered, since those frames we want
traced fully are most likely linear anyway, but the code gets easier
to understand and we lose an argument to the tracing function, so
overall fixing this is better.
Fixes: 206eea7833 ("iwlwifi: pcie: support frag SKBs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to calculate the data_len outside of the tracepoint,
since it's always skb->len - hdr_len, which are both available inside.
Simplify the callers and move the calculation in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use kstrtou32_from_user() in debugfs instead of open-coding it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't actually care about the value at all, just making sure
that we can successfully parse a single integer value, but that's
entirely pointless - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When toggling the RF-kill pin quickly in succession, the driver can
get rather confused because it might be in the process of shutting
down, expecting all commands to go through quickly due to rfkill,
but the transport already thinks the device is accessible again,
even though it previously shut it down. This leads to bugs, and I
even observed a kernel panic.
Avoid this by making the PCIe code only report that the radio is
enabled again after the higher layers actually decided to shut it
off.
This also pulls out this common RF-kill checking code into a common
function called by both transport generations and also moves it to
the direct method - in the internal helper we don't really care
about the RF-kill status anymore since we won't report it up until
the stop anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to debug "hardware" RF-kill flows, add a low-level hook to
allow changing the "hardware" RF-kill from debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in duplicating exactly the same code here
for legacy and MSI-X interrupts, so pull it out into a new
function to call in both places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Letting the preprocessor/compiler generate the shift/mask by itself
is a win for readability, so use bitfield.h for some registers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The queue ID should never be 512 either, so correct the check
to be >= instead of just >.
Fixes: 310181ec34 ("iwlwifi: move to TVQM mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Loads of FW API documentation improvements (for tools and htmldoc);
* Continued work for the new A000 family;
* Bumped the maximum supported FW API to 31;
* Improve the differentiation between 8000, 9000 and A000 families;
* A lot of fixes and cleanups here and there;
-----BEGIN PGP SIGNATURE-----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=oYeO
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-06-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi driver patches 4.13
* Loads of FW API documentation improvements (for tools and htmldoc);
* Continued work for the new A000 family;
* Bumped the maximum supported FW API to 31;
* Improve the differentiation between 8000, 9000 and A000 families;
* A lot of fixes and cleanups here and there;
kvalo: There were conflicts iwl_mvm_stop_device() and
iwl_mvm_tcool_set_cur_state(). The former was easy but latter needed more
thought. Apparently the mutex was taken too late, so I fixed so that the mutex
is taken first and then check for iwl_mvm_firmware_running().
FH in A000 HW are placed in a different location,
and need to be read as prph, rather than direct.
Support A000 dumping as well as legacy.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add two new device families to differentiate them from 8000.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is essentially the same code as gen1, except that it uses
gen2 functions and SW checksum is not included.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sending host command with CMD_WANT_SKB flag demands the release of the
response buffer with iwl_free_resp function.
The patch adds the memory release in all the relevant places
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We only need to handle d0i3 entry and exit during suspend resume if
system_pm is set to IWL_PLAT_PM_MODE_D0I3, otherwise d0i3 entry
failures will cause suspend to fail.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194791
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we have 512 queues, add a wait for single TX
queue to gen2.
This replaces gen1 wait_tx_queues_empty, which was limited
to 32 queues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In gen2, page dumping needs to be done in the trans
layer, as it is the one with access to the paging
pointers.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Three configurations will share device ID 2720, and will
be differentiated by RF ID.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This API replaces the complex NVM parsing of the iwlwifi module.
Instead, we get all needed data from firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When applying no-reclaim logic to commands other than the group
zero for legacy commands, commands such as 0x1c (TX_CMD in group
0) can't be used in any other group. Fix that by applying this
logic only for group 0 - it's not and should never be needed for
any other groups.
Reported-by: Sharon Dvir <sharon.dvir@intel.com>
Reported-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rename current wait_tx_queue_empty to wait_tx_queues_empty since
it waits for multiple queues (up to 32).
Next patch will add a wait for single TX queue which is needed for
gen2 to be scalable for 512.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avoid using the old define since it will enlarge necessary
structs for previous HW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This struct member is already assigned in the previous
call to iwl_trans_alloc(), so assigning the same value
again is superfluous - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If iwl_pcie_ctxt_info_init_fw_sec() fails, the previous allocated DMA
memory needs to be freed (it even goes out of scope immediately.)
Do that to prevent the leak.
Fixes: eda50cde58 ("iwlwifi: pcie: add context information support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the context info fails to be allocated, the mutex
isn't unlocked properly, fix that.
Fixes: eda50cde58 ("iwlwifi: pcie: add context information support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add one new PCI ID for the 8265 series.
Add three new PCI ID for the 8275 series.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In TVQM firmware returns the value of the queue ID and code
should accept it.
The TX queue config API was changed. Move to new API.
This has to be done in parallel in mvm and pcie.
Do not move yet to 512 queues since there are some opens
with enabling it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In TVQM mode the queue ID is assigned after enablement.
Get rid of assuming pre-defined TX queue ID in functions
that will be used by TVQM allocation path.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change queue allocation to be dynamic. On transport init only
the command queue is being allocated. Other queues are allocated
on demand.
This is due to the huge amount of queues we will soon enable (512)
and as a preparation for TX Virtual Queue Manager feature (TVQM),
where firmware will assign the actual queue number on demand.
This includes also allocation of the byte count table per queue
and not as a contiguous chunk of memory.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is basically the same as gen1, except for clean
ups of old devices configuration that are never used in a000
configuration.
It will also help with refactoring rf_kill later on.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 transport we will allocate queues dynamically.
Right now queue are allocated as one big chunk of memory
and accessed as such.
The dynamic allocation of the queues will require accessing
the queues as pointers.
In order to keep simplicity of pre-a000 tx queues handling,
keep allocating and freeing the memory in the same style,
but move to access the queues in the various functions as
individual pointers.
Dynamic allocation for the a000 devices will be in a separate
patch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New transport will be used only by op modes that supports
buffer station offload - hence those will never be called.
Clean it up.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 devices we have 16 bytes for the TFD index and 16 for the
queue, in order to support 512 queues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Code is basically the same, with a cleanups of old narrow host
command, ampg workarounds, some cosmetic stuff, and usage of
TFH functions when accessing TFD queues.
This enables also the cleanup of iwl_pcie_tfd_set_tb() since
now it won't be called anywhere in the a000 data path
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move to use the correct structure.
Remove code referring to old command.
Update DMA locations.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Cleanup code that is irrelevant for a000 devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is just a copy-paste in order to make changes tracking
easier.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 devices the TX handling is different in a few ways:
* Queues are allocated dynamically
* DQA is enabled by default
* Driver shouldn't access TFH registers - ucode configures it
all in SCD_QUEUE_CFG command
Support all this in a new API with op mode, where op mode sends
the command, transport will allocate the queue dynamically, fill
in DMA properties, send the command to FW and get the ID back.
Current implementation only sets the new transport API and fills
the DMA properties.
Future patches will complete the other parts.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Context information structure is going to be used in a000
devices for firmware self init.
The self init includes firmware self loading from DRAM by
ROM.
This means the TFH relevant firmware loading can be cleaned up.
The firmware loading includes the paging memory as well, so op
mode can stop initializing the paging and sending the DRAM_BLOCK_CMD.
Firmware is doing RFH, TFH and SCD configuration, while driver
only fills the required configurations and addresses in the
context information structure.
The only remaining access to RFH is the write pointer, which
is updated upon alive interrupt after FW configured the RFH.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
a000 devices are going to have a lot of flows simplified
and changed: init flow, RX, TX, and more.
This, combined with the fact that code is already very
complicated due to backward compatibility - introduce
a split that will enable to introduce simplified version
of functions.
Shared ops are moved to a macro, while functions that will
be updated in the next patches are defined twice for now.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't need this parameter anymore, since we always pass 0 anyway.
Remove it from the structure and from all the relevant functions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use iwl_get_dma_hi_addr() instead of open-coding it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This register is helpful for debugging D3 issues.
Driver turns all bits on, and then on exit reads the
updated value there.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We already have queue_used in the transport - we can
use it instead.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts commit 8aacf4b73f ("iwlwifi: introduce trans API
to get byte count table").
The commit is not needed as a better approach will be taken.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't need to print so much data in the kernel log.
Limit the data to be printed to the queue that actually
got stuck in case of a TFD queue hang, and stop dumping
all the CSR and FH registers. Over the course of time, the
CSR and FH values haven't proven themselves to be really
useful for debugging, and they are now in the firmware dump
anyway.
This comes as a preparation to the addition of more data
required to be printed by the firwmare team.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
One of the RF modules we support has been deprecated and never
released publicly. Remove support for this module.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, when getting a RFKILL interrupt, the transport enters a flow
in which it stops the device, disables other interrupts, etc. After
stopping the device, the transport resets the hw, and sleeps. During
the sleep, a context switch occurs and host commands are sent by upper
layers (e.g. mvm) to the fw. This is possible since the op_mode layer
and the transport layer hold different mutexes.
Since the STATUS_RFKILL bit isn't set, the transport layer doesn't
recognize that RFKILL was toggled on, and no commands can actually be
sent, so it enqueues the command to the tx queue and sets a timer on
the queue.
After switching context back to stopping the device, STATUS_RFKILL is
set, and then the transport can't send the command to the fw.
This eventually results in a queue hang.
Fix this by setting STATUS_RFKILL immediately when
the interrupt is fired.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
