Commit Graph

39729 Commits

Author SHA1 Message Date
Stefan Richter
2a0a259049 firewire: wait until PHY configuration packet was transmitted (fix bus reset loop)
We now exit fw_send_phy_config /after/ the PHY config packet has been
transmitted, instead of before.  A subsequent fw_core_initiate_bus_reset
will therefore not overlap with the transmission.  This is meant to make
the send PHY config packet + reset bus routine more deterministic.

Fixes bus reset loop and eventual panic with
  - VIA VT6307 + IOGEAR hub + Unibrain Fire-i camera
    http://bugzilla.kernel.org/show_bug.cgi?id=10128
  - JMicron card

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:36 +02:00
Stefan Richter
e09770db0f firewire: remove unused struct member
request_generation is internal to fw-ohci and unneeded in fw_card.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:36 +02:00
Jarod Wilson
15f0d833f6 firewire: use bitwise and to get reg in handle_registers
for code efficiency.

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:36 +02:00
Jarod Wilson
cca6097713 firewire: replace more hex values with defined csr constants
Trivial change to replace more meaningless (to the untrained eye) hex
values with defined CSR constants.

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:36 +02:00
Stefan Richter
c9755e14a0 firewire: reread config ROM when device reset the bus
When a device changes its configuration ROM, it announces this with a
bus reset.  firewire-core has to check which node initiated a bus reset
and whether any unit directories went away or were added on this node.

Tested with an IOI FWB-IDE01AB which has its link-on bit set if bus
power is available but does not respond to ROM read requests if self
power is off.  This implements
  - recognition of the units if self power is switched on after fw-core
    gave up the initial attempt to read the config ROM,
  - shutdown of the units when self power is switched off.

Also tested with a second PC running Linux/ieee1394.  When the eth1394
driver is inserted and removed on that node, fw-core now notices the
addition and removal of the IPv4 unit on the ieee1394 node.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:36 +02:00
Stefan Richter
1dadff71d6 firewire: replace static ROM cache by allocated cache
read_bus_info_block() is repeatedly called by workqueue jobs.
These will step on each others toes eventually if there are multiple
workqueue threads, and we end up with corrupt config ROM images.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:35 +02:00
Stefan Richter
d34316a4bd firewire: fw-ohci: work around generation bug in TI controllers (fix AV/C and more)
Unlike the ohci1394 driver, fw-ohci uses the selfIDGeneration field of
bus reset packets to determine the generation of incoming requests as
per OHCI 1.1 clause 8.4.2.3.  This is more precise --- provided that the
controller inserts the correct generation.  Texas Instruments chips
often don't.

This prevented the transmission of response packets, which for example
broke AV/C transactions as used when communicating with miniDV cameras
and any other AV/C devices.

There is apparently no way to detect and adjust incorrect generations.
Therefore we ignore the generation of bus reset packets from TI chips
and use the generation of the self ID buffer instead.  Alas this is
received at a slightly wrong time.  In rare cases, this could cause us
to not respond to legitimate requests or to respond to expired requests.
(The latter is less likely because the bus reset packet AR event is
typically handled before the self ID complete event.)

Bug reported by Mladen Kuntner, who was extraordinarily patient while
dealing with the driver maintainers.  Fix confirmed to be required and
effective for TSB82AA2 and a TSB43AB22 or TSB43AB22A.
https://bugzilla.redhat.com/show_bug.cgi?id=243081

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:35 +02:00
Stefan Richter
08ddb2f4c2 firewire: fw-ohci: extend logging of bus generations and node ID
Extend the logging of "AR evt_bus_reset, link internal" to "AR
evt_bus_reset, generation ${selfIDGeneration}".  That way we can check
whether this generation matches the one seen in self ID complete event
logging.  See OHCI 1.1 clause 8.4.2.3.

Also extend logging of "firewire_ohci: * selfIDs, generation *" by
"local node ID ffc*" in self ID logging to make the local node in AT/AR
event logs more obvious.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:35 +02:00
Stefan Richter
a007bb857e firewire: fw-ohci: conditionally log busReset interrupts
Add a debug option to watch bus reset interrupt events.  Half of this
patch is taken from Jarod Wilson's first version of the JMicron fix.

BusReset interrupts are only generated if the respective module
parameter flag was set before the controller is being initialized.
Else we keep this event masked to reduce IRQ load in normal operation
and to avoid potential problems with buggy chips.

Note, this is unlike the other IRQ events whose logging can be enabled
any time after chip initialization.  This and the influence on what
interrupts the chip generates is why I added an extra flag for it.

Also, reorder the debug parameter flags according to their perceived
usefulness.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:35 +02:00
Jarod Wilson
76f73ca1b2 firewire: fw-ohci: don't append to AT context when it's not active
I finally tracked down the issues with this JMicron PCI-e card in my
possession to a failure to comply with section 7.2.3.2 of the OHCI 1.1
specification (thanks to Kristian for the pointer to illustrate that it
is indeed a flaw in this card, not the driver). The controller should
simply flush the packets we've appended to its AT queue if a bus reset
occurs before they've been transmitted and we'll try again, but
something goes wrong and the controller winds up hung.

However, we can avoid the problem by simply checking if the
IntEvent.busReset register had been set before we try appending to the
AT context. When busReset is set, the AT context is completely halted
until busReset is cleared, so there's no point in appending AT packets
until the register is cleared. So at_context_queue_packet() now checks
for busReset being set, and bails with an RCODE_GENERATION packet ack,
which results in us trying to append the packet again after recognizing
the fact there has been a bus reset, and clearing busReset.

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:35 +02:00
Jarod Wilson
75f7832e3b firewire: fw-ohci: log regAccessFail events
While trying to debug this piece of crap JMicron PCI-e controller in my
possession, one thought was that perhaps I was encountering register access
failures. I'm not, but logging them would be good, so we can see if they
are a real problem we should be taking into account anywhere in the code.

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added list contact)
2008-04-18 17:55:34 +02:00
Jarod Wilson
022147242f firewire: fw-ohci: make sure HCControl register LPS bit is set
I've now witnessed multiple occasions where one of my controllers (a very
poorly working JMicron PCIe card) fails to get its registers properly set
up in ohci_enable(), apparently due to an occasionally very slow to
initiate SClk. The easy fix for this problem is to add a tiny while loop
to try again a time or three after initially enabling LPS before we
move on (or give up).

Of course, the card still isn't fully functional yet, but this gets it at
least one tiny step closer...

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:34 +02:00
Stefan Richter
130d5496e2 firewire: fw-ohci: missing PPC PMac feature calls in failure path
Balance ohci_pmac_on and ohci_pmac_off if pci_driver.probe fails.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:34 +02:00
Stefan Richter
43286568ad firewire: fw-ohci: untangle a mixed unsigned/signed expression
and make another expression more readable.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:34 +02:00
Stefan Richter
ad3c0fe8b8 firewire: debug interrupt events
This adds debug printks for asynchronous transmission and reception and
for self ID reception.  They can be enabled at module load time, and at
runtime via /sys/module/firewire_ohci/parameters/debug.

Signed-off-by: Jarod Wilson <jwilson@redhat.com>

Also added:  Logging of interrupt event codes and of cancelled AT
packets.

The code now depends on a Kconfig variable.  This makes it easier to
build firewire-ohci without the feature or to make it an option in the
future.  The variable is currently hidden and always on.

This feature inflates firewire-ohci.ko by 7 kB = 27% on x86-64 and by
4 kB = 23% on i686.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:34 +02:00
Stefan Richter
016bf3dfcf firewire: fw-ohci: catch self_id_count == 0
fw_core_handle_bus_reset() incorrectly relied on the assumption that
self_id_count > 0.

We check early in fw-ohci and discard the self ID complete event if
self_id_count == 0 because a valid event always has at least one self ID
packet in it (the one of the local node).  Hence treat self_id_count ==
0 like any other kind of invalid self ID buffer.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:34 +02:00
Stefan Richter
c8a9a498e1 firewire: fw-ohci: add self ID error check
Discard self ID buffer contents if
  - the selfIDError flag is set,
  - any of the self ID packets has bit errors.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:33 +02:00
Stefan Richter
2ed0f181f0 firewire: fw-ohci: refactor probe, remove, suspend, resume
Clean up shared code and variable names.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:33 +02:00
Stefan Richter
eb5ca72eff firewire: fw-ohci: switch on bus power after resume on PPC PMac
The platform feature calls in the suspend method switched off cable
power, but the calls in the resume method did not switch it back on.

Add the necessary feature call to .resume.  Also add the corresponding
call to .suspend to make .suspend's behavior explicitly the same on all
PMacs.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:33 +02:00
Stefan Richter
080de8c2c5 firewire: fw-ohci: add option for remote debugging
This way firewire-ohci can be used for remote debugging like ohci1394.
Version with amendment from Fri, 11 Apr 2008 00:08:08 +0200.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Bernhard Kaindl <bk@suse.de>
2008-04-18 17:55:33 +02:00
Jarod Wilson
17cff9ff87 firewire: fw-sbp2: set dual-phase cycle_limit
Try to write dual-phase retry protocol limits to BUSY_TIMEOUT register.
- The dual-phase retry protocol is optional to implement, and if not 
  supported, writes to the dual-phase portion of the register will be
  ignored. We try to write the original 1394-1995 default here.
- In the case of devices that are also SBP-3-compliant, all writes are 
  ignored, as the register is read-only, but contains single-phase retry of
  15, which is what we're trying to set for all SBP-2 device anyway, so this
  write attempt is safe and yields more consistent behavior for all devices.

See section 8.3.2.3.5 of the 1394-1995 spec, section 6.2 of the SBP-2 spec,
and section 6.4 of the SBP-3 spec for further details.

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:33 +02:00
Stefan Richter
a5fd9ec7a2 firewire: fw-sbp2: reduce log noise
The block/unblock logic is now sufficiently tested.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:32 +02:00
Stefan Richter
6f73100cbb firewire: fw-sbp2: remove unnecessary memset
orb came from kzalloc.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:32 +02:00
Stefan Richter
0d7dcbf2a3 firewire: fw-sbp2: simplify some macros
How hard can it be to switch on one bit? :-)

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:32 +02:00
Stefan Richter
71ee9f01f2 firewire: fw-sbp2: remove usages of fw_memcpy_to_be32
Write directly in big endian instead of byte-swapping after the fact.
This saves a few conversions, lets gcc use constant endianess
conversions where possible, and enables deeper endianess annotation.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:32 +02:00
Stefan Richter
8ac3a47cab firewire: fw-sbp2: relax SCSI DMA alignment
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:32 +02:00
Stefan Richter
1dc3bea78b firewire: refactor fw_unit reference counting
Add wrappers for getting and putting a unit.
Remove some line breaks.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:32 +02:00
Stefan Richter
7c1fca3366 firewire: fw-sbp2: fix reference counting
The reference count of the unit dropped too low in an error path in
sbp2_probe.  Fixed by moving the _get further up.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:31 +02:00
Stefan Richter
bd7dee6311 firewire: remove superfluous reference counting
The card->kref became obsolete since patch "firewire: fix crash in
automatic module unloading" added another counter of card users.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:31 +02:00
Philippe De Muyter
a6ca4f7081 ieee1394: limit early node speed to host interface speed
The following patch limits the node speed to the host interface speed,
before using it.

Signed-off-by: Philippe De Muyter <phdm@macqel.be>

It should actually suffice to do this only for the local node's
speedcap[].  But there is another bug in the speed calculation:
The local node's speed is not correctly propagated to the speeds
which are to be used to access remote nodes.
http://thread.gmane.org/gmane.linux.kernel.firewire.devel/11772/focus=12024

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:31 +02:00
Robert P. J. Day
ee2d91e2b3 ieee1394: Remove superfluous calls to kobject_set_name().
Unless you're adding a kobject to the sysfs hierarchy, there is no
point setting its kobject name.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:31 +02:00
Stefan Richter
9508c208aa ieee1394: ohci1394: missing PPC PMac feature calls in failure path
The failure path of ohci1394_pci_probe() reuses ohci1394_pci_remove().
Doing so it missed to call ohci1394_pmac_off() in a few unlikely early
error cases.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:31 +02:00
Stefan Richter
c4e2e02bc9 ieee1394: ohci1394: refactor some printk format strings
to reduce the size of ohci1394.ko.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:31 +02:00
Stefan Richter
d09c680383 ieee1394: ohci1394: unroll a macro with return
We don't want to hide something like return in a preprocessor macro.
Unroll the macro and use a goto, which also reduces the size of
ohci1394.ko.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:30 +02:00
Robert P. J. Day
e351c4d069 ieee1394: Use shorter list_splice_init() for brevity.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:30 +02:00
Harvey Harrison
b1ce1fd778 ieee1394: replace remaining __FUNCTION__ occurrences
__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:30 +02:00
Stefan Richter
b25d166616 ieee1394: ohci1394: refactor probe, remove, suspend, resume
Clean up shared code and variable names.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:30 +02:00
Stefan Richter
38275ac36d ieee1394: ohci1394: switch on bus power after resume on PPC PMac
The platform feature calls in the suspend method switched off cable
power, but the calls in the resume method did not switch it back on.

Add the necessary feature call to .resume.  Also add the corresponding
call to .suspend to make .suspend's behavior explicitly the same on all
PMacs.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:30 +02:00
Stefan Richter
d2ace29fa4 ieee1394: prevent device binding of raw1394, video1394, dv1394
These drivers don't need to match any unit_directory type device.
They just need the id_table for module autoloading per module alias.

Not binding any of these drivers allows special-purpose drivers with
similar or same IDs to bind to devices.  This currently only benefits
out-of-tree drivers; on the other hand it is in no way detrimental to
in-tree drivers.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:29 +02:00
Marcin Slusarz
63995d4650 ieee1394: be*_add_cpu conversion
replace all:
big_endian_variable = cpu_to_beX(beX_to_cpu(big_endian_variable) +
					expression_in_cpu_byteorder);
with:
	beX_add_cpu(&big_endian_variable, expression_in_cpu_byteorder);
generated with semantic patch

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:29 +02:00
Stefan Richter
a4b47d62c5 ieee1394: sbp2: relax SCSI DMA alignment
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:29 +02:00
Linus Torvalds
188da98800 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (58 commits)
  ide: remove ide_init_default_irq() macro
  ide: move default IDE ports setup to ide_generic host driver
  ide: remove obsoleted "idex=noprobe" kernel parameter (take 2)
  ide: remove needless hwif->irq check from ide_hwif_configure()
  ide: init hwif->{io_ports,irq} explicitly in legacy VLB host drivers
  ide: limit legacy VLB host drivers to alpha, x86 and mips
  cmd640: init hwif->{io_ports,irq} explicitly
  cmd640: cleanup setup_device_ptrs()
  ide: add ide-4drives host driver (take 3)
  ide: remove ppc ifdef from init_ide_data()
  ide: remove ide_default_io_ctl() macro
  ide: remove CONFIG_IDE_ARCH_OBSOLETE_INIT
  ide: add CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS (take 2)
  ppc/pmac: remove no longer needed IDE quirk
  ppc: don't include <linux/ide.h>
  ppc: remove ppc_ide_md
  ppc/pplus: remove ppc_ide_md.ide_init_hwif hook
  ppc/sandpoint: remove ppc_ide_md hooks
  ppc/lopec: remove ppc_ide_md hooks
  ppc/mpc8xx: remove ppc_ide_md hooks
  ...
2008-04-18 08:39:24 -07:00
Linus Torvalds
07fe944e87 Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
  dmaengine: ack to flags: make use of the unused bits in the 'ack' field
  iop-adma: remove the workaround for missed interrupts on iop3xx
  async_tx: kill ->device_dependency_added
  async_tx: fix multiple dependency submission
  fsldma: Split the MPC83xx event from MPC85xx and refine irq codes.
  fsldma: Remove CONFIG_FSL_DMA_SELFTEST, keep fsl_dma_self_test() running always.
2008-04-18 08:38:55 -07:00
Linus Torvalds
8019aa946a Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (79 commits)
  ata-acpi: don't call _GTF for disabled drive
  sata_mv add temporary 3 second init delay for SiliconImage PMs
  sata_mv remove redundant edma init code
  sata_mv add basic port multiplier support
  sata_mv fix SOC flags, enable NCQ on SOC
  sata_mv disable hotplug for now
  sata_mv cosmetics
  sata_mv hardreset rework
  [libata] improve Kconfig help text for new PMP, SFF options
  libata: make EH fail gracefully if no reset method is available
  libata: Be a bit more slack about early devices
  libata: cable logic
  libata: move link onlineness check out of softreset methods
  libata: kill dead code paths in reset path
  pata_scc: fix build breakage
  libata: make PMP support optional
  libata: implement PMP helpers
  libata: separate PMP support code from core code
  libata: make SFF support optional
  libata: don't use ap->ioaddr in non-SFF drivers
  ...
2008-04-18 08:38:06 -07:00
Linus Torvalds
9732b61123 Merge git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-kgdb
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-kgdb:
  kgdb: always use icache flush for sw breakpoints
  kgdb: fix SMP NMI kgdb_handle_exception exit race
  kgdb: documentation fixes
  kgdb: allow static kgdbts boot configuration
  kgdb: add documentation
  kgdb: Kconfig fix
  kgdb: add kgdb internal test suite
  kgdb: fix several kgdb regressions
  kgdb: kgdboc pl011 I/O module
  kgdb: fix optional arch functions and probe_kernel_*
  kgdb: add x86 HW breakpoints
  kgdb: print breakpoint removed on exception
  kgdb: clocksource watchdog
  kgdb: fix NMI hangs
  kgdb: fix kgdboc dynamic module configuration
  kgdb: document parameters
  x86: kgdb support
  consoles: polling support, kgdboc
  kgdb: core
  uaccess: add probe_kernel_write()
2008-04-18 08:37:01 -07:00
Linus Torvalds
d7bb545d86 Merge branch 'semaphore' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc
* 'semaphore' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc:
  Remove DEBUG_SEMAPHORE from Kconfig
  Improve semaphore documentation
  Simplify semaphore implementation
  Add down_timeout and change ACPI to use it
  Introduce down_killable()
  Generic semaphore implementation
  Add semaphore.h to kernel_lock.c
  Fix quota.h includes
2008-04-18 08:25:29 -07:00
Linus Torvalds
75e98b3415 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (104 commits)
  IB/iser: Don't change itt endianness
  IB/mlx4: Update module version and release date
  IPoIB: Handle case when P_Key is deleted and re-added at same index
  IB/iser: Release connection resources on RDMA_CM_EVENT_DEVICE_REMOVAL event
  IB/mlx4: Fix incorrect comment
  IB/mlx4: Fix race when detaching a QP from a multicast group
  IB/ehca: Support all ibv_devinfo values in query_device() and query_port()
  RDMA/nes: Free IRQ before killing tasklet
  IB/mthca: Update module version and release date
  IB/mlx4: Update QP state if query QP succeeds
  IB/mthca: Update QP state if query QP succeeds
  RDMA/amso1100: Add check for NULL reply_msg in c2_intr()
  IB/mlx4: Add support for resizing CQs
  IB/mlx4: Add support for modifying CQ moderation parameters
  IPoIB: Support modifying IPoIB CQ event moderation
  IB/core: Add support for modify CQ
  IPoIB: Add basic ethtool support
  mlx4_core: Increase max number of QPs to 128K
  RDMA/amso1100: Add support for "send with invalidate" work requests
  IB/core: Add support for "send with invalidate" work requests
  ...
2008-04-18 08:20:06 -07:00
David S. Miller
1e42198609 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6 2008-04-17 23:56:30 -07:00
Bartlomiej Zolnierkiewicz
273b8385e5 ide: remove ide_init_default_irq() macro
* Use ide_default_irq() instead of ide_init_default_irq() in
  ide_generic host driver (so the correct IRQ is always set
  regardless of CONFIG_PCI / CONFIG_BLK_DEV_IDEPCI).

* Remove no longer needed ide_init_default_irq() macro.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:35 +02:00
Bartlomiej Zolnierkiewicz
486c92e290 ide: move default IDE ports setup to ide_generic host driver
* Make CONFIG_IDE_GENERIC depended on CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS.

* Move default IDE ports setup from init_ide_data() to ide_generic.

* Use ide_init_port_hw() in ide_generic.

* Remove no longer needed CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:35 +02:00
Bartlomiej Zolnierkiewicz
f01674e459 ide: remove obsoleted "idex=noprobe" kernel parameter (take 2)
* Remove obsoleted "idex=noprobe" kernel parameter.

* Remove no longer needed hwif->noprobe quirk from ide_hwif_configure()
  and hwif->noprobe checking from cmd640.c.

v2:
* "ide?=noprobe" -> "ide?=ata66" in Documentation/kernel-parameters.txt.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:35 +02:00
Bartlomiej Zolnierkiewicz
aab8ad9ec8 ide: remove needless hwif->irq check from ide_hwif_configure()
ide_init_default_irq() is always zero for CONFIG_PCI=y so hwif->irq
check in ide_hwif_configure() can be safely removed.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:35 +02:00
Bartlomiej Zolnierkiewicz
dfd87842a9 ide: init hwif->{io_ports,irq} explicitly in legacy VLB host drivers
Do explicit port setup in legacy VLB host drivers instead of depending
on init_ide_data().  This way hwif->io_ports[] and hwif->irq are always
correctly set regardless of CONFIG_PCI / CONFIG_BLK_DEV_IDEPCI.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:35 +02:00
Bartlomiej Zolnierkiewicz
e4079df0c2 ide: limit legacy VLB host drivers to alpha, x86 and mips
These host drivers indirectly depend on CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS=y
which is defined only on alpha, x86, ia64, m32r, mips and ppc32.

Moreover:

- on ia64 there is no ISA

- m32r is too new for VLB

- on ppc32 ISA is available only on PPC_CHRP (no default IDE ports)
  and PPC_PREP (marked as BROKEN)

[ the common sense tells me that VLB was only used on x86 but there
  are urban legends that one of these host drivers was needed on some
  other arch - thus the extra care ]

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:35 +02:00
Bartlomiej Zolnierkiewicz
6d3803b68e cmd640: init hwif->{io_ports,irq} explicitly
Do explicit port setup instead of depending on init_ide_data().

This way hwif->io_ports[] and hwif->irq are always correctly set
regardless of CONFIG_PCI / CONFIG_BLK_DEV_IDEPCI.

While at it fix printk().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:34 +02:00
Bartlomiej Zolnierkiewicz
daaad24fdc cmd640: cleanup setup_device_ptrs()
This loop is no longer needed.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:34 +02:00
Bartlomiej Zolnierkiewicz
ffd4f6f0ee ide: add ide-4drives host driver (take 3)
CONFIG_BLK_DEV_4DRIVES deserves its own host driver:

* Add drivers/ide/legacy/ide-4drives.c and move "4drives" support there.

* Add ide-4drives.o in the link order after all other legacy host
  drivers enabled by "ide0=" options (they all are mutually exclusive).

* Make ide-4drives host driver probe itself for IDE devices instead of
  indirectly depending on ide_generic host driver.

* Add "probe" module parameter to ide-4drives and update documentation.

v2:
* s/paramater/parameter/ in ide.txt. (Noticed by Randy Dunlap)

v3:
* s/ide_4drives.probe/ide-4drives.probe/ in help entry.
  (Noticed by Sergei Shtylyov)

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:34 +02:00
Bartlomiej Zolnierkiewicz
26d799b729 ide: remove ppc ifdef from init_ide_data()
On PPC32 ide_init_default_irq() is non-zero only for PPLUS and PPC_PREP
(the latter marked as BROKEN currently) so this ifdef can be removed.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:34 +02:00
Bartlomiej Zolnierkiewicz
9dfcd15a6d ide: remove ide_default_io_ctl() macro
It is always == '((base) + 0x206)' if CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS=y
and it is not needed otherwise (arm, blackfin, parisc, ppc64, sh, sparc[64]).

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:34 +02:00
Bartlomiej Zolnierkiewicz
5c50427090 ide: remove CONFIG_IDE_ARCH_OBSOLETE_INIT
* Use CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS instead of
  CONFIG_IDE_ARCH_OBSOLETE_INIT in init_ide_data().

* Remove no longer needed CONFIG_IDE_ARCH_OBSOLETE_INIT.

There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:33 +02:00
Bartlomiej Zolnierkiewicz
0e33555fff ide: add CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS (take 2)
* Add CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS to drivers/ide/Kconfig and use
  it instead of defining IDE_ARCH_OBSOLETE_DEFAULTS in <arch/ide.h>.

v2:
* Define ide_default_irq() in ide-probe.c/ns87415.c if not already defined
  and drop defining ide_default_irq() for CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS=n.

  [ Thanks to Stephen Rothwell and David Miller for noticing the problem. ]

Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:33 +02:00
Bartlomiej Zolnierkiewicz
1d850bd0b2 ppc: remove ppc_ide_md
* Add special cases for pplus and prep to ide_default_{irq,io_base}()
  (+ FIXMEs about the need to use IDE platform host driver instead).

* Remove no longer needed ppc_ide_md and struct ide_machdep_calls.

* Then remove <linux/ide.h> include from:
  - arch/powerpc/kernel/setup_32.c
  - arch/ppc/kernel/ppc_ksyms.c
  - arch/ppc/kernel/setup.c
  - arch/ppc/platforms/pplus.c
  - arch/ppc/platforms/prep_setup.c

There should be no functional changes caused by this patch.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:32 +02:00
Bartlomiej Zolnierkiewicz
5d682e4407 ppc/pplus: remove ppc_ide_md.ide_init_hwif hook
* Call ide_init_default_irq() for pplus in init_ide_data().

* Remove no longer needed pplus_ide_init_hwif_ports().

There should be no functional changes caused by this patch.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:31 +02:00
Bartlomiej Zolnierkiewicz
7ef8df81de ppc/sandpoint: remove ppc_ide_md hooks
* Add IDE_HFLAG_FORCE_LEGACY_IRQS host flag for Motorola-Sandpoint platform
  to sl82c105 host driver.

* Disable ide_generic host driver in arch/ppc/configs/sandpoint_defconfig
  and enable sl82c105 one.

* Remove ppc_ide_md hooks from arch/ppc/platforms/sandpoint.c - no need for
  them (sl82c105 host driver takes care of all this setup).

* Then remove no longer needed <linux/ide.h> include.

* Also update arch/ppc/platforms/sandpoint.h.

Unfortunately (unlike lopec's case) sl82c105 host driver was not enabled
in defconfing so there is a funcionality change.

[ Not a big deal since sl82c105 is superior over ide_generic. ]

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:30 +02:00
Bartlomiej Zolnierkiewicz
5510b12557 ppc/lopec: remove ppc_ide_md hooks
* Add IDE_HFLAG_FORCE_LEGACY_IRQS host flag for Motorola-LoPEC platform
  to sl82c105 host driver.

* Remove ppc_ide_md hooks from arch/ppc/platforms/lopec.c - no need for
  them (sl82c105 host driver takes care of all this setup).

* Then remove no longer needed <linux/ide.h> include.

Looking at arch/ppc/configs/lopec_defconfig:

...
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_IDEPCI_SHARE_IRQ is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_SL82C105=y
...

there should be no functional changes unless somebody preferred to disable
sl82c105 host driver and use only ide_generic one (but why would anybody
want to do such thing :-).

PS It seems that lopec_defconfig hasn't been updated for ages but if somebody
is going to do it please look into disabling IDE_GENERIC and BLK_DEV_GENERIC
config options.  Thanks.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:29 +02:00
Bartlomiej Zolnierkiewicz
2661b13a21 ppc/mpc8xx: remove ppc_ide_md hooks
* Initialize IDE ports in mpc8xx_ide_probe().

* Remove m8xx_ide_init() and ppc_ide_md hooks - no need for them
  (IDE mpc8xx host driver takes care of all this setup).

* Remove needless 'if (irq)' and 'if (data_port >= MAX_HWIFS)' checks
  from m8xx_ide_init_hwif_ports().

* Remove 'ctrl_port' and 'irq' arguments from m8xx_ide_init_hwif_ports().

* Rename m8xx_ide_init_hwif_ports() to m8xx_ide_init_ports().

* Add __init tag to m8xx_ide_init_ports().

This patch fixes hwif->irq always being overriden to 0 (== auto-probe, is
this even working on PPC?) because of ide_init_default_irq() call in ide.c.

There should be no other functional changes.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:29 +02:00
Bartlomiej Zolnierkiewicz
5c58666fae ppc/pmac: remove ppc_ide_md hooks
* Add pmac_ide_init_ports() helper and use it instead of
  pmac_ide_init_hwif_ports().

* Remove ppc_ide_md hooks - no need for them
  (IDE pmac host driver takes care of all this setup).

* Then remove no longer needed <linux/ide.h> include
  from arch/powerpc/platforms/powermac/pmac.h.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:29 +02:00
Bartlomiej Zolnierkiewicz
af007ec6c9 ide-pmac: remove dead code
Remove unused pmac_ide_{check_base,get_irq}() and pmac_find_ide_boot(),
then remove no longer needed ide_majors[] and pmac_ide_count.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:28 +02:00
Borislav Petkov
e3bfae4c10 ide-scsi: do non-atomic pc->flags testing
...also, convert ide-scsi to using the generic pc->flags defines.

Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:27 +02:00
Borislav Petkov
eaec3e7ded ide: use generic ATAPI packet command flags in ide-{floppy,tape}
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:27 +02:00
Borislav Petkov
c2b2b29361 ide-floppy: rename end_request handler properly
mv idefloppy_do_end_request -> idefloppy_end_request as is the case with ide-cd

Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:27 +02:00
Borislav Petkov
1c065787c0 ide-scsi: convert driver to using generic ide_atapi_pc
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:27 +02:00
Borislav Petkov
8e55512391 ide-floppy: convert driver to using generic ide_atapi_pc
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:27 +02:00
Borislav Petkov
d236d74c0d ide-tape: convert driver to using generic ide_atapi_pc
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:27 +02:00
Borislav Petkov
346331f828 ide-tape: remove atomic test/set macros for packet commands
Removing the atomic tests for pc's is unobjectionable. Since this driver will
probably go to /dev/null soon, the atomic tests for tape->flags are left in
place for there are some situations where they're needed (chrdev DSC handling,
low level pipeline operation and so on). While at it, rename all test/set flag
bit defines explicitly to *_FLAG_* for clarity.

Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:26 +02:00
Borislav Petkov
03056b909b ide-tape: move all struct and other defs at the top
Bart:
- no need to move defines for tape flags around
  (they are completely rewritten by the next patch)

Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:26 +02:00
Bartlomiej Zolnierkiewicz
23579a2a17 ide: remove IDE_*_REG macros
* Add IDE_{ALTSTATUS,IREASON,BCOUNTL,BCOUNTH}_OFFSET defines.

* Remove IDE_*_REG macros - this results in more readable
  and slightly smaller code.

There should be no functional changes caused by this patch.

Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:26 +02:00
Bartlomiej Zolnierkiewicz
7616c0ad20 ide: add ide_atapi_{discard_data,write_zeros} inline helpers
Add ide_atapi_{discard_data,write_zeros} inline helpers to <linux/ide.h>
and use them instead of home-brewn helpers in ide-{floppy,tape,scsi}.

There should be no functional changes caused by this patch.

Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:26 +02:00
Borislav Petkov
3ad6776cca ide-floppy: remove struct idefloppy_id_gcw
Bart:
- minor fixups

Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:25 +02:00
Akira Iguchi
3d53ba87f0 scc_pata.c: do setup itself instead of ide_setup_pci_device()
scc_pata has the different BAR configuration and using ide_setup_pci_device()
is inappropriate. 

(ide_setup_pci_device() expects a normal PCI IDE controller with
BAR0..BAR3 either non-existant or being primary/secondary port bases
in I/O space.)

This patch do all needed setup itself instead of calling ide_setup_pci_device().

[bart: minor checkpatch.pl fixes]

Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:25 +02:00
Bartlomiej Zolnierkiewicz
e6bfa38a48 ide: remove ide_init_hwif_ports()
ide_init_hwif_ports() is only used by init_ide_data() now, inline it there.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:25 +02:00
Bartlomiej Zolnierkiewicz
05734266c0 ide: remove init_hwif_default()
init_hwif_default() is only used by init_ide_data() now, inline it there.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:25 +02:00
Bartlomiej Zolnierkiewicz
2304dc6481 ide: remove ->hold field from ide_hwif_t (take 2)
->hold is write-only now, remove it.

v2:
* v1 missed bast-ide, palm_bk3710, ide-cs and delkin_cb host drivers.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:24 +02:00
Bartlomiej Zolnierkiewicz
93de00fd1c ide: remove broken/dangerous HDIO_[UNREGISTER,SCAN]_HWIF ioctls (take 3)
hdparm explicitely marks HDIO_[UNREGISTER,SCAN]_HWIF ioctls as DANGEROUS
and given the number of bugs we can assume that there are no real users:

* DMA has no chance of working because DMA resources are released by
  ide_unregister() and they are never allocated again.

* Since ide_init_hwif_ports() is used for ->io_ports[] setup the ioctls
  don't work for almost all hosts with "non-standard" (== non ISA-like)
  layout of IDE taskfile registers (there is a lot of such host drivers).

* ide_port_init_devices() is not called when probing IDE devices so:
  - drive->autotune is never set and IDE host/devices are not programmed
    for the correct PIO/DMA transfer modes (=> possible data corruption)
  - host specific I/O 32-bit and IRQ unmasking settings are not applied
    (=> possible data corruption)
  - host specific ->port_init_devs method is not called (=> no luck with
    ht6560b, qd65xx and opti621 host drivers)

* ->rw_disk method is not preserved (=> no HPT3xxN chipsets support).

* ->serialized flag is not preserved (=> possible data corruption when
   using icside, aec62xx (ATP850UF chipset), cmd640, cs5530, hpt366
   (HPT3xxN chipsets), rz1000, sc1200, dtc2278 and ht6560b host drivers).

* ->ack_intr method is not preserved (=> needed by ide-cris, buddha,
  gayle and macide host drivers).

* ->sata_scr[] and sata_misc[] is cleared by ide_unregister() and it
  isn't initialized again (SiI3112 support needs them).

* To issue an ioctl() there need to be at least one IDE device present
  in the system.

* ->cable_detect method is not preserved + it is not called when probing
  IDE devices so cable detection is broken (however since DMA support is
  also broken it doesn't really matter ;-).

* Some objects which may have already been freed in ide_unregister()
  are restored by ide_hwif_restore() (i.e. ->hwgroup).

* ide_register_hw() may unregister unrelated IDE ports if free ide_hwifs[]
  slot cannot be found.

* When IDE host drivers are modular unregistered port may be re-used by
  different host driver that owned it first causing subtle bugs.

Since we now have a proper warm-plug support remove these ioctls,
then remove no longer needed:
- ide_register_hw() and ide_hwif_restore() functions
- 'init_default' and 'restore' arguments of ide_unregister()
- zeroeing of hwif->{dma,extra}_* fields in ide_unregister()

As an added bonus IDE core code size shrinks by ~3kB (x86-32).

v2:
* fix ide_unregister() arguments in cleanup_module() (Andrew Morton).

v3:
* fix ide_unregister() arguments in palm_bk3710.c.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:24 +02:00
Bartlomiej Zolnierkiewicz
9a0e77f28b ide: remove obsoleted "idex=base[,ctl[,irq]]" kernel parameters (take 2)
* Remove obsoleted "idex=base[,ctl[,irq]]" kernel parameters
  and update Documentation/ide/ide.txt.

* Remove no longer needed ide_forced chipset type.

v2:
* is_chipset_set[] -> is_chipset_set in ide.c.

* Documentation/ide/ide.txt fix.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:24 +02:00
Bartlomiej Zolnierkiewicz
80aa31cb46 ide: remove CONFIG_BLK_DEV_HD_IDE config option (take 2)
* Remove CONFIG_BLK_DEV_HD hack from init_hwif_default()
  ("hda=noprobe hdb=noprobe" kernel parameters should be used
  instead if somebody wishes to use the old "hd" driver).

* Make CONFIG_BLK_DEV_HD_ONLY config option available also when
  IDE subsystem is used and update help entry.

* Remove no longer needed CONFIG_BLK_DEV_HD_IDE config option.

v2:
* Update documentation to suggest "hda=noprobe hdb=noprobe"
  instead of obsoleted "ide0=noprobe".

* Update Documentation/ide/ide.txt.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:24 +02:00
Bartlomiej Zolnierkiewicz
fef39d95ea ide: remove needless CONFIG_BLK_DEV_HD hack from init_hwif()
request_irq() will fail if there is already another IRQ handler
registered and IRQ flags are mismatched.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:23 +02:00
Bartlomiej Zolnierkiewicz
f0298512c8 ide-generic: add ide_generic class and attribute for adding new interfaces
* Add ide_generic_sysfs_init() helper registering 'ide_generic' class
  (together with ide_generic_class_release() ->class_release method)
  and use it in ide_generic_init().

* Add "add" class attribute to 'ide_generic' class for adding new interfaces
  (it is intended to be a replacement for obsoleted "idex=base[,ctl[,irq]]"
  kernel parameters).

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:23 +02:00
Bartlomiej Zolnierkiewicz
f74c91413e ide: add warm-plug support for IDE devices (take 2)
* Add 'struct class ide_port_class' ('ide_port' class) and a 'struct
  device *portdev' ('ide_port' class device) in ide_hwif_t.

* Register 'ide_port' class in ide_init() and unregister it in
  cleanup_module().

* Create ->portdev in ide_register_port () and unregister it in
  ide_unregister().

* Add "delete_devices" class device attribute for unregistering IDE devices
  on a port and "scan" one for probing+registering IDE devices on a port.

* Add ide_sysfs_register_port() helper for registering "delete_devices"
  and "scan" attributes with ->portdev.  Call it in ide_device_add_all().

* Document IDE warm-plug support in Documentation/ide/warm-plug-howto.txt.

v2:
* Convert patch from using 'struct class_device' to use 'struct device'.
  (thanks to Kay Sievers for doing it)

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:23 +02:00
Bartlomiej Zolnierkiewicz
50672e5d74 ide: remove dead/obsolete ->busproc method
->busproc method is used by HDIO_SET_BUSSTATE ioctl but it has no chance
of working as intended (in 2.4.x days) because to issue an ioctl there
is a device node needed and:

- for BUSSTATE_TRISTATE+OFF it is too late (devices are already gone)

- for BUSSTATE_TRISTATE+ON it is too early (devices are not registered yet)

Just remove ->busproc method for now (it was only implemented by hpt366,
siimage and tc86c001 host drivers).

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:23 +02:00
Bartlomiej Zolnierkiewicz
2dde7861af ide: rework PowerMac media-bay support (take 2)
Rework PowerMac media-bay support in such way that instead of
un/registering the IDE interface we un/register IDE devices:

* Add ide_port_scan() helper for probing+registerering devices on a port.

* Rename ide_port_unregister_devices() to __ide_port_unregister_devices().

* Add ide_port_unregister_devices() helper for unregistering devices on a port.

* Add 'ide_hwif_t *cd_port' to 'struct media_bay_info', pass 'hwif' instead
  of hwif->index to media_bay_set_ide_infos() and use it to setup 'cd_port'.

* Use ide_port_unregister_devices() instead of ide_unregister()
  and ide_port_scan() instead of ide_register_hw() in media_bay_step().

* Unexport ide_register_hw() and make it static.

v2:
* Fix build by adding <linux/ide.h> include to <asm-powerpc/mediabay.h>.
  (Reported by Michael/Kamalesh/Andrew).

Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:23 +02:00
Bartlomiej Zolnierkiewicz
26042d058b ide: move ide_port_setup_devices() call to ide_device_add_all()
Add ide_cfg_mtx lock/unlock to ide_port_setup_devices() and then move
ide_port_setup_devices() call from init_irq() to ide_device_add_all().

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:22 +02:00
Bartlomiej Zolnierkiewicz
43514ed1ee ide: factor out devices init from ide_init_port_data()
* Factor out devices init from ide_init_port_data() to
  ide_port_init_devices_data().

While at it:

* Add explicit clearing of IDE device structure.

There should be no functionality changes caused by this patch.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:22 +02:00
Bartlomiej Zolnierkiewicz
71bf9f6fe8 ide: factor out code unregistering devices from ide_unregister()
Factor out code unregistering devices from ide_unregister() to
ide_port_unregister_devices().

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:22 +02:00
Bartlomiej Zolnierkiewicz
5b0c4b30a6 ide: remove IDE devices from /proc/ide/ before unregistering them
IDE devices need to be removed from /proc/ide/ _before_ being unregistered:

* Drop 'ide_hwif_t *hwif' argument from destroy_proc_ide_device()
  and use drive->hwif instead.

* Rename destroy_proc_ide_device() to ide_proc_unregister_device().

* Call ide_proc_unregister_device() in drive_release_dev().

* Remove no longer needed destroy_proc_ide_drives().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:22 +02:00
Bartlomiej Zolnierkiewicz
c7f6f21aae ide: factor out cable detection from ide_init_port()
* Factor out cable detection from ide_init_port() to ide_port_cable_detect().

* Move ide_port_cable_detect() call to ide_device_add_all().

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:22 +02:00
Bartlomiej Zolnierkiewicz
8f22a72bf5 ide-acpi: add missing drive->acpidata zeroing
There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:21 +02:00
Bartlomiej Zolnierkiewicz
4f0eee4d87 ide: use ide_find_port() instead of ide_deprecated_find_port()
* Use ide_find_port() instead of ide_deprecated_find_port() in bast-ide/
  palm_bk3710/ide-cs/delkin_cb host drivers and in ide_register_hw().

* Remove no longer needed ide_deprecated_find_port().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:21 +02:00
Bartlomiej Zolnierkiewicz
2625cd52b6 ide: fix ide_find_port()
* Instead of checking for '->io_ports[IDE_DATA_OFFSET] == 0' check for
  '->chipset == ide_unknown' when looking for an empty ide_hwifs[] slot.

* Do ide-pnp initialization after ide-generic when IDE is built-in
  (ide-pnp is the only user of ide_find_port() which needs such fixup).

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:21 +02:00
Bartlomiej Zolnierkiewicz
ce9b248bb4 ide-generic: set hwif->chipset
This hwif->chipset fixup is already present in ide_device_add_all()
but for warm-plug support we also need to reserve not currently present
interfaces.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:21 +02:00
Greg Kroah-Hartman
a594eeb1a1 IDE: remove ide=reverse IDE core
This option is obsolete and can be removed safely.

It allows us to remove the pci_get_device_reverse() function from the
PCI core.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-04-18 00:46:20 +02:00
David S. Miller
2e5a3eaca3 Merge branch 'upstream-net26' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6 2008-04-17 14:13:13 -07:00
Dan Williams
636bdeaa12 dmaengine: ack to flags: make use of the unused bits in the 'ack' field
'ack' is currently a simple integer that flags whether or not a client is done
touching fields in the given descriptor.  It is effectively just a single bit
of information.  Converting this to a flags parameter allows the other bits to
be put to use to control completion actions, like dma-unmap, and capture
results, like xor-zero-sum == 0.

Changes are one of:
1/ convert all open-coded ->ack manipulations to use async_tx_ack
   and async_tx_test_ack.
2/ set the ack bit at prep time where possible
3/ make drivers store the flags at prep time
4/ add flags to the device_prep_dma_interrupt prototype

Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:25:54 -07:00
Dan Williams
c4fe15541d iop-adma: remove the workaround for missed interrupts on iop3xx
This workaround was covering the dependency submission bug in async_tx.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:25:54 -07:00
Dan Williams
ce4d65a5db async_tx: kill ->device_dependency_added
DMA drivers no longer need to be notified of dependency submission
events as async_tx_run_dependencies and async_tx_channel_switch will
handle the scheduling and execution of dependent operations.

[sfr@canb.auug.org.au: extend this for fsldma]
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:25:54 -07:00
Dan Williams
19242d7233 async_tx: fix multiple dependency submission
Shrink struct dma_async_tx_descriptor and introduce
async_tx_channel_switch to properly inject a channel switch interrupt in
the descriptor stream.  This simplifies the locking model as drivers no
longer need to handle dma_async_tx_descriptor.lock.

Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:25:05 -07:00
Zhang Wei
1c62979ed2 fsldma: Split the MPC83xx event from MPC85xx and refine irq codes.
Split MPC83xx EOCDI event from MPC85xx EOLNI event, which is
also need to update cookie and start the next transfer.
The DMA channel irq handler function code is refined.
The patch is tested on MPC8377MDS board.

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by; Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:22:16 -07:00
Zhang Wei
411e23dbe9 fsldma: Remove CONFIG_FSL_DMA_SELFTEST, keep fsl_dma_self_test() running always.
Always enabling the fsl_dma_self_test() to ensure the DMA controller
should works well after the driver probed.

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-04-17 13:22:15 -07:00
Shaohua Li
48feb3c419 ata-acpi: don't call _GTF for disabled drive
I got below log after a S3 resume in a ASUS A6VC laptop. The system has
only one IDE drive. It appears there is no reason calling _GTF for
disabled drive.

ACPI Error (dsopcode-0483): Attempt to CreateField of length zero [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.RATA] (Node df822a7c), AE_AML_OPERAND_VALUE
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN1.DRV0._GTF] (Node df822bd0), AE_AML_OPERAND_VALUE
ata2.00: _GTF evaluation failed (AE 0x3006)
ACPI Error (dsopcode-0483): Attempt to CreateField of length zero [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.RATA] (Node df822a7c), AE_AML_OPERAND_VALUE
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN1.DRV1._GTF] (Node df822b94), AE_AML_OPERAND_VALUE
ata2.01: _GTF evaluation failed (AE 0x3006)

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:29 -04:00
Mark Lord
094e50b2f7 sata_mv add temporary 3 second init delay for SiliconImage PMs
sata_mv does not yet fully support hotplug (coming soon, though).
This means that the driver may not find a Silicon Image port-multiplier
when first loaded, because those devices take in exceess of 3 seconds
to sync up the SATA PHY (most devices do this in mere microseconds).

So, as a short-term interim measure, here we insert a 3-second pause
on initial driver load, once per controller board (not once per port!),
to allow the Silicon Image port-multipliers to be detected later.

This will be removed again (soon!) once hotplug is fully implemented/working.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:25 -04:00
Mark Lord
8a74f1a468 sata_mv remove redundant edma init code
Remove unnecessary edma init code from port_start.
This sequence gets done later on the first I/O to the port.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:21 -04:00
Mark Lord
e49856d82a sata_mv add basic port multiplier support
Add basic port-multiplier support to sata_mv.
This works in Command-based-switching mode for Gen-II chipsets,
and in FIS-based-switching mode for Gen-IIe chipsets.

Error handling remains at the primary port level for now
(works okay, but not great).  This will get fixed in a subsequent
patch series for IRQ/EH handling fixes.  There are also some
known NCQ/PMP errata to be dealt with in the near future,
once we have this basic PMP support in place.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:19 -04:00
Mark Lord
02c1f32f1c sata_mv fix SOC flags, enable NCQ on SOC
The System-On-Chip (SOC) core supports all of the same
features as the other recent Marvell chips,
including NCQ and IRQ coalescing.

Fix the chip_soc flags to enable these capabilities
(note that the driver currently does nothing special
for IRQ coalescing, though).

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:16 -04:00
Mark Lord
40f0bc2d77 sata_mv disable hotplug for now
Disable hot plug/unplug detection in sata_mv for now.
It is currently broken, and also interferes with PMP support.

This will get fixed in a subsequent patch series.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:12 -04:00
Mark Lord
17c5aab5b3 sata_mv cosmetics
More cosmetic cleanups to unclutter the changes needed for PMP support.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:08 -04:00
Mark Lord
0d8be5cbff sata_mv hardreset rework
Rework and simplify sata_mv's hardreset code to take advantage of
libata improvements since it was first coded.

Also, get rid of the now unnecessary prereset, postreset, and phy_reset
functions.

This patch also paves the way for subsequent pmp support patches,
which will follow once this one passes muster.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:05 -04:00
Jeff Garzik
f3360ebffa [libata] improve Kconfig help text for new PMP, SFF options 2008-04-17 15:55:24 -04:00
Tejun Heo
4f7faa3f2b libata: make EH fail gracefully if no reset method is available
When no reset method is available, libata currently oopses.  Although
the condition can't happen unless there's a bug in a low level driver,
oopsing isn't the best way to report the error condition.  Complain,
dump stack and fail reset instead.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:26 -04:00
Alan Cox
b93fda1235 libata: Be a bit more slack about early devices
We have a certain number of 'ATA' emulations often on CF or other flash
devices that are at best "loosely based" on the CF 1.1 standard. These
devices report themselves as disk but don't support the ATA minimal
command set only the CF 1.1 set.

Relax the PIO checking for devices reporting ATA rev 0, or no iordy
support, or CFA. Rework the code a bit as it was already messy and this
made it quite ugly.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:25 -04:00
Alan Cox
f792068e43 libata: cable logic
The cable detect isolation patch inadvertently removed 40 wire short
cable handling. Put it back

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
45db2f6c95 libata: move link onlineness check out of softreset methods
Currently, SATA softresets should do link onlineness check before
actually performing SRST protocol but it doesn't really belong to
softreset.

This patch moves onlineness check in softreset to ata_eh_reset() and
ata_eh_followup_srst_needed() to clean up code and help future sata_mv
changes which need clear separation between SCR and TF accesses.

sata_fsl is peculiar in that its softreset really isn't softreset but
combination of hardreset and softreset.  This patch adds dummy private
->prereset to keep the current behavior but the driver really should
implement separate hard and soft resets and return -EAGAIN from
hardreset if it should be follwed by softreset.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
2a0c15ca39 libata: kill dead code paths in reset path
Some code paths which had been made obsolete by recent reset
simplification were still around.  Kill them.

* ata_eh_reset() checked for ATA_DEV_UNKNOWN to determine
  classification failure.  This is no longer applicable.

* ata_do_reset() should convert ATA_DEV_UNKNOWN to ATA_DEV_NONE
  regardless of reset result (e.g. -EAGAIN).

* LLDs don't need to convert ATA_DEV_UNKNOWN to ATA_DEV_NONE.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:25 -04:00
Stephen Rothwell
e50e3ce5e7 pata_scc: fix build breakage
drivers/ata/pata_scc.c: In function 'scc_bus_softreset':
drivers/ata/pata_scc.c:594: error: 'deadlien' undeclared (first use in this function)
drivers/ata/pata_scc.c:594: error: (Each undeclared identifier is reported only once
drivers/ata/pata_scc.c:594: error: for each function it appears in.)

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:25 -04:00
Tejun Heo
88fcd56275 libata: make PMP support optional
Make PMP support optional by adding CONFIG_SATA_PMP and leaving out
libata-pmp.c if it isn't set.  PMP helpers return constant values if
PMP support is not enabled and PMP declarations alias non-PMP
counterparts.  This makes the compiler to leave out PMP related part
out and LLDs to use non-PMP counterparts automatically.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
071f44b1d2 libata: implement PMP helpers
Implement helpers to test whether PMP is supported, attached and
determine pmp number to use when issuing SRST to a link.  While at it,
move ata_is_host_link() so that it's together with the two new PMP
helpers.

This change simplifies LLDs and helps making PMP support optional.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
48515f6c00 libata: separate PMP support code from core code
Most of PMP support code is already in libata-pmp.c.  All that are in
libata-core.c are sata_pmp_port_ops and EXPORTs.  Move them to
libata-pmp.c.  Also, collect PMP related prototypes and declarations
in header files and move them right above of SFF stuff.

This change is to make PMP support optional.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
127102aea2 libata: make SFF support optional
Now that SFF support is completely separated out from the core layer,
it can be made optional.  Add CONFIG_ATA_SFF and let SFF drivers
depend on it.  If CONFIG_ATA_SFF isn't set, all codes in libata-sff.c
and data structures for SFF support are disabled.  This saves good
number of bytes for small systems.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:24 -04:00
Tejun Heo
350756f6da libata: don't use ap->ioaddr in non-SFF drivers
ap->ioaddr is to carry addresses for TF and BMDMA registers of a SFF
controller, don't abuse it in non-SFF controllers.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:24 -04:00
Tejun Heo
182d7bbac3 libata: clean up dummy port_ops
Now that SFF assumptions are removed from core layer, dummy port_ops
can be slimmed down.  Chop it down.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:24 -04:00
Tejun Heo
c9f75b04ed libata: kill ata_noop_dev_select()
Now that SFF assumptions are separated out from non-SFF reset
sequence, port_ops->sff_dev_select() is no longer necessary for
non-SFF controllers.  Kill ata_noop_dev_select() and ->sff_dev_select
initialization from base and other non-SFF port_ops.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:24 -04:00
Tejun Heo
520d06f92b libata: remove check_status from non-SFF drivers
Now that all SFF stuff is separated out of core layer, core layer
doesn't call ops->[alt_]check_status().  In fact, no one calls them
for non-SFF drivers anymore.  Kill them.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:24 -04:00
Tejun Heo
4c9bf4e799 libata: replace tf_read with qc_fill_rtf for non-SFF drivers
Now that all SFF stuff is separated out of core layer, core layer
doesn't call ops->tf_read directly.  It gets called only via
ops->qc_fill_rtf() for non-SFF drivers.  This patch directly
implements private ops->qc_fill_rtf() for non-SFF controllers and kill
ops->tf_read().

This is much cleaner for non-SFF controllers as some of them have to
cache SFF register values in private data structure and report the
cached values via ops->tf_read().  Also, ops->tf_read() gets nasty for
controllers which don't have clear notion of TF registers when
operation is not in progress.

As this change makes default ops->qc_fill_rtf unnecessary, move
ata_sff_qc_fill_rtf() form ata_base_port_ops to ata_sff_port_ops where
it belongs.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
79f97dadfe libata: drop @finish_qc from ata_qc_complete_multiple()
ata_qc_complete_multiple() took @finish_qc and called it on every qc
before completing it.  This was to give opportunity to update TF cache
before ata_qc_complete() tries to fill result_tf.  Now that result TF
is a separate operation, this is no longer necessary.

Update sata_sil24, which was the only user of this mechanism, such
that it implements its own ops->qc_fill_rtf() and drop @finish_qc from
ata_qc_complete_multiple().

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
22183bf569 libata: add qc_fill_rtf port operation
On command completion, ata_qc_complete() directly called ops->tf_read
to fill qc->result_tf.  This patch adds ops->qc_fill_rtf to replace
hardcoded ops->tf_read usage.

ata_sff_qc_fill_rtf() which uses ops->tf_read to fill result_tf is
implemented and set in ata_base_port_ops and other ops tables which
don't inherit from ata_base_port_ops, so this patch doesn't introduce
any behavior change.

ops->qc_fill_rtf() is similar to ops->sff_tf_read() but can only be
called when a command finishes.  As some non-SFF controllers don't
have TF registers defined unless they're associated with in-flight
commands, this limited operation makes life easier for those drivers
and help lifting SFF assumptions from libata core layer.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
305d2a1ab1 libata: unify mechanism to request follow-up SRST
Previously, there were two ways to trigger follow-up SRST from
hardreset method - returning -EAGAIN and leaving all device classes
unmodified.  Drivers never used the latter mechanism and the only use
case for the former was when hardreset couldn't classify.

Drop the latter mechanism and let -EAGAIN mean "perform follow-up SRST
if classification is required".  This change removes unnecessary
follow-up SRSTs and simplifies reset implementations.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
5958e3025f libata: move PMP SCR access failure during reset to ata_eh_reset()
If PMP fan-out reset fails and SCR isn't accessible, PMP should be
reset.  This used to be tested by sata_pmp_std_hardreset() and
communicated to EH by -ERESTART.  However, this logic is generic and
doesn't really have much to do with specific hardreset implementation.

This patch moves SCR access failure detection logic to ata_eh_reset()
where it belongs.  As this makes sata_pmp_std_hardreset() identical to
sata_std_hardreset(), the function is killed and replaced with the
standard method.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
ac371987a8 libata: clear SError after link resume
SError used to be cleared in ->postreset.  This has small hotplug race
condition.  If a device is plugged in after reset is complete but
postreset hasn't run yet, its hotplug event gets lost when SError is
cleared.  This patch makes sata_link_resume() clear SError.  This
kills the race condition and makes a lot of sense as some PMP and host
PHYs don't work properly without SError cleared.

This change makes sata_pmp_std_{pre|post}_reset()'s unnecessary as
they become identical to ata_std counterparts.  It also simplifies
sata_pmp_hardreset() and ahci_vt8251_hardreset().

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
57c9efdfb3 libata: implement and use sata_std_hardreset()
Implement sata_std_hardreset(), which simply wraps around
sata_link_hardreset().  sata_std_hardreset() becomes new standard
hardreset method for sata_port_ops and sata_sff_hardreset() moves from
ata_base_port_ops to ata_sff_port_ops, which is where it really
belongs.

ata_is_builtin_hardreset() is added so that both
ata_std_error_handler() and ata_sff_error_handler() skip both builtin
hardresets if SCR isn't accessible.

piix_sidpr_hardreset() in ata_piix.c is identical to
sata_std_hardreset() in functionality and got replaced with the
standard function.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
9dadd45b24 libata: move generic hardreset code from sata_sff_hardreset() to sata_link_hardreset()
sata_sff_hardreset() contains link readiness wait logic which isn't
SFF specific.  Move that part into sata_link_hardreset(), which now
takes two more parameters - @online and @check_ready.  Both are
optional.  The former is out parameter for link onlineness after
reset.  The latter is used to wait for link readiness after hardreset.

Users of sata_link_hardreset() is updated to use new funtionality and
ahci_hardreset() is updated to use sata_link_hardreset() instead of
sata_sff_hardreset().  This doesn't really cause any behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
a89611e848 ahci: use ata_wait_after_reset() instead of ata_sff_wait_ready()
Implement ahci_check_ready() and replace ata_sff_wait_after_reset()
with ata_wait_after_reset().  As ahci was faking TF access, this
change doesn't result in any functional difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
aa2731ad9a libata: separate out ata_wait_ready() and implement ata_wait_after_reset()
Factor out waiting logic (which is common to all ATA controllers) from
ata_sff_wait_ready() into ata_wait_ready().  ata_wait_ready() takes
@check_ready function pointer and uses it to poll for readiness.  This
allows non-SFF controllers to use ata_wait_ready() to wait for link
readiness.

This patch also implements ata_wait_after_reset() - generic version of
ata_sff_wait_after_reset() - using ata_wait_ready().

ata_sff_wait_ready() is reimplemented using ata_wait_ready() and
ata_sff_check_ready().  Functionality remains the same.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
705e76beb9 libata: restructure SFF post-reset readiness waits
Previously, post-softreset readiness is waited as follows.

1. ata_sff_wait_after_reset() waits for 150ms and then for
   ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.

2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff.
   If not, continue to .

3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending
   on devmask using ata_sff_wait_ready().

And for post-hardreset readiness,

1. ata_sff_wait_after_reset() waits for 150ms and then for
   ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.

2. sata_sff_hardreset waits for device readiness using
   ata_sff_wait_ready().

This patch merges and unifies post-reset readiness waits into
ata_sff_wait_ready() and ata_sff_wait_after_reset().

ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready().  If TF
status is 0xff, link status is unknown and the port is SATA, it will
continue polling till ATA_TMOUT_FF_WAIT.

ata_sff_wait_after_reset() is updated to perform the following steps.

1. waits for 150ms.

2. waits for dev0 readiness using ata_sff_wait_ready().  Note that
   this is done regardless of devmask, as ata_sff_wait_ready() handles
   0xff status correctly, this preserves the original behavior except
   that it may wait longer after softreset if link is online but
   status is 0xff.  This behavior change is very unlikely to cause any
   actual difference and is intended.  It brings softreset behavior to
   that of hardreset.

3. waits for dev1 readiness just the same way ata_bus_post_reset() did.

Now both soft and hard resets call ata_sff_wait_after_reset() after
reset to wait for readiness after resets.  As
ata_sff_wait_after_reset() contains calls to ->sff_dev_select(),
explicit call near the end of sata_sff_hardreset() is removed.

This change makes reset implementation simpler and more consistent.

While at it, make the magical 150ms wait post-reset wait duration a
constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take
@link instead of @ap.  This is to make them consistent with other
reset helpers and ease core changes.

pata_scc is updated accordingly.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
203c75b824 libata: separate out ata_std_postreset() from ata_sff_postreset()
Separate out generic ATA portion from ata_sff_postreset() into
ata_std_postreset() and implement ata_sff_postreset() using the std
version.

ata_base_port_ops now has ata_std_postreset() for its postreset and
ata_sff_port_ops overrides it to ata_sff_postreset().

This change affects pdc_adma, ahci, sata_fsl and sata_sil24.  pdc_adma
now specifies postreset to ata_sff_postreset() explicitly.  sata_fsl
and sata_sil24 now use ata_std_postreset() which makes no difference
to them.  ahci now calls ata_std_postreset() from its own postreset
method, which causes no behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
0aa1113d54 libata: separate out ata_std_prereset() from ata_sff_prereset()
Separate out generic ATA portion from ata_sff_prereset() into
ata_std_prereset() and implement ata_sff_prereset() using the std
version.  Waiting for device readiness is the only SFF specific part.

ata_base_port_ops now has ata_std_prereset() for its prereset and
ata_sff_port_ops overrides it to ata_sff_prereset().  This change can
affect pdc_adma, ahci, sata_fsl and sata_sil24.  pdc_adma implements
its own prereset using ata_sff_prereset() and the rest has hardreset
and thus are unaffected by this change.

This change reflects real world situation.  There is no generic way to
wait for device readiness for non-SFF controllers and some of them
don't have any mechanism for that.  Non-sff drivers which don't have
hardreset should wrap ata_std_prereset() and wait for device readiness
itself but there's no such driver now and isn't likely to be popular
in the future either.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
288623a06c libata: clean up port_ops->sff_irq_clear()
->sff_irq_clear() is called only from SFF interrupt handler, so there
is no reason to initialize it for non-SFF controllers.  Also,
ata_sff_irq_clear() can handle both BMDMA and non-BMDMA SFF
controllers.

This patch kills ata_noop_irq_clear() and removes it from base
port_ops and sets ->sff_irq_clear to ata_sff_irq_clear() in sff
port_ops instead of bmdma port_ops.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
5682ed33aa libata: rename SFF port ops
Add sff_ prefix to SFF specific port ops.

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames ops and doesn't introduce any
behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
9363c3825e libata: rename SFF functions
SFF functions have confusing names.  Some have sff prefix, some have
bmdma, some std, some pci and some none.  Unify the naming by...

* SFF functions which are common to both BMDMA and non-BMDMA are
  prefixed with ata_sff_.

* SFF functions which are specific to BMDMA are prefixed with
  ata_bmdma_.

* SFF functions which are specific to PCI but apply to both BMDMA and
  non-BMDMA are prefixed with ata_pci_sff_.

* SFF functions which are specific to PCI and BMDMA are prefixed with
  ata_pci_bmdma_.

* Drop generic prefixes from LLD specific routines.  For example,
  bfin_std_dev_select -> bfin_dev_select.

The following renames are noteworthy.

  ata_qc_issue_prot() -> ata_sff_qc_issue()
  ata_pci_default_filter() -> ata_bmdma_mode_filter()
  ata_dev_try_classify() -> ata_sff_dev_classify()

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames functions and doesn't
introduce any behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:21 -04:00
Mark Lord
b67a1064cb sata_mv fix ifctl handling
Fix handling of the SATA_INTERFACE_CFG register to match datasheet requirements.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:21 -04:00
Mark Lord
b562468cc3 sata_mv clean up mv_stop_edma usage
Clean up uses of mv_stop_edma{_engine}() to match datasheet requirements.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:21 -04:00
Mark Lord
e12bef50b7 sata_mv cosmetic fixes
Various cosmetic fixes in preparation for real code changes later on.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:21 -04:00
Chris Wedgwood
c30484d775 Add 'short help text' to ATA_ACPI so it's [de]selectable.
ATA_ACPI isn't selectable right now because it lacks 'short help
text'.  This means it's always enabled and always enables ACPI_DOCK.
Add text so it's now [de]selectable.

cc: Jeff Garzik <jeff@garzik.org>
cc: Tejun Heo <htejun@gmail.com>
cc: Len Brown <len.brown@intel.com>
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:21 -04:00
Tejun Heo
fc4712d12e pdc_adma: kill adma_host_stop()
adma_host_stop() does the same thing that adma_port_stop() does.  Kill
it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:21 -04:00
Tejun Heo
b0316b15ac pdc_adma: inherit ata_sff_port_ops
With the previous ops standardization, pdc_adma now can inherit
ata_sff_port_ops instead of ata_base_port_ops.  Make the change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
ed82f96425 libata/pdc_adma: make SFF EH handle non-bmdma SFF drivers and standardize pdc_adma ops
pdc_adma has interface similar to SFF but has its own DMA interface.
It currently implements noop bmdma ops to avoid crashing
ata_bmdma_error_handler() which BTW actually is EH for SFF drivers.

This patch makes ata_bmdma_error_handler() dereference bmdma ops iff
bmdma_addr is initialized as done in ata_bmdma_post_internal_cmd.
This change allows pdc_adma to standardize ops and use SFF
error_handler and post_internal_cmd.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
d8b81b8008 libata: kill unused ata_flush_cache()
ata_flush_code() hasn't been in use for quite some time now.  Kill it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
03faab7827 libata: implement ATA_QCFLAG_RETRY
Currently whether a command should be retried after failure is
determined inside ata_eh_finish().  Add ATA_QCFLAG_RETRY and move the
logic into ata_eh_autopsy().  This makes things clearer and helps
extending retry determination logic.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
a5987e0a1b libata: make ata_tf_to_lba[48]() generic
ata_tf_to_lba[48]() currently return LBA in tf + 1 for
ata_read_native_max_address().  Make them return LBA and make it
global so that it can be used to read LBA off TF for other purposes.
ata_read_native_max_address() now adds 1 itself.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Jeff Garzik
06993d2237 [libata] sata_nv: disable ADMA by default
Continues to have open issues, and engineering support is extremely difficult
to come by, according to fellow NVIDIA engineers.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:20 -04:00
Al Viro
826cd156de libata annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
9c0bf67505 ata_piix: kill ich6_sata_ahci and clean up
ich6_sata_ahci and ich6_sata are identical.  Kill ich6_sata_ahci and
drop _ahci postfixes from controller ids, which doesn't really mean
anything at this point.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
5016d7d212 ata_piix: don't attach to ICH6M in ahci mode
ata_piix when attached to ICH6M in AHCI mode doesn't provide any
benefit over using ahci and has detection problems.  Don't let
ata_piix claim ICH6M if it's in AHCI mode.

This change makes ICH6R the only one which ata_piix can attach to even
when it's in ahci mode which is necessary as some devices don't work
properly under ahci mode.  Drop PIIX_FLAG_AHCI and match the
controller directly so that piix_disable_ahci() is called only for it.

This change makes PIIX_SCC no longer used and it gets dropped too.

This fixes bz 9491.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Robert M. Albrecht <romal@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:19 -04:00
Tejun Heo
c1796d9850 pata_scc: fix compile warning
Missed one during mass conversion (dc14c0c5).  Fix it.  Spotted by
Stephen Rothwell.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:19 -04:00
Alan Cox
15a5551c84 libata: isolate and rework cable logic
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:19 -04:00
Zoltan Boszormenyi
d21279f412 ata: SWNCQ should be enabled by default
Signed-off-by: Zoltan Boszormenyi <zboszor@dunaweb.hu>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:19 -04:00
Harvey Harrison
d9c74fbead pata_amd: fix sparse warning
Current code is essentially choosing between dividing by 1 or
dividing by two, make the conditions a little more obvious.

As a bonus, removes a sparse error:
drivers/ata/pata_amd.c:59:11: warning: symbol '__x' shadows an earlier one
drivers/ata/pata_amd.c:59:11: originally declared here

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
6fd3639011 libata: kill ata_chk_status()
ata_chk_status() just calls ops->check_status and it only adds
confusion with other status functions.  Kill it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
3d5a3d67a5 libata: kill ata_chk_status() call from ata_dev_configure()
ata_dev_configure() isn't tied to any controller interface except for
the probe debug message printing at the end of the function.  Kill the
message.

This is to help separating out SFF support from core layer.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
071ce34d57 libata: move ata_pci_default_filter() out of CONFIG_PCI
ata_pci_default_filter() doesn't really have anything to do with PCI.
It's generally applicable to BMDMA controllers.  Move it out of
CONFIG_PCI.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
624d5c514e libata: reorganize SFF related stuff
* Move SFF related functions from libata-core.c to libata-sff.c.

  ata_[bmdma_]sff_port_ops, ata_devchk(), ata_dev_try_classify(),
  ata_std_dev_select(), ata_tf_to_host(), ata_busy_sleep(),
  ata_wait_after_reset(), ata_wait_ready(), ata_bus_post_reset(),
  ata_bus_softreset(), ata_bus_reset(), ata_std_softreset(),
  sata_std_hardreset(), ata_fill_sg(), ata_fill_sg_dumb(),
  ata_qc_prep(), ata_dump_qc_prep(), ata_data_xfer(),
  ata_data_xfer_noirq(), ata_pio_sector(), ata_pio_sectors(),
  atapi_send_cdb(), __atapi_pio_bytes(), atapi_pio_bytes(),
  ata_hsm_ok_in_wq(), ata_hsm_qc_complete(), ata_hsm_move(),
  ata_pio_task(), ata_qc_issue_prot(), ata_host_intr(),
  ata_interrupt(), ata_std_ports()

* Make ata_pio_queue_task() global as it's now called from
  libata-sff.c.

* Move SFF related stuff in include/linux/libata.h and
  drivers/ata/libata.h into one place.  While at it, move timing
  constants into the global enum definition and fortify comments a
  bit.

This patch strictly moves stuff around and as such doesn't cause any
functional difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
272f7884e8 libata: reorder functions in libata-sff.c
Reorder functions in drivers/ata/libata-sff.c such that functions
generally follow ops table order and init functions come last.  This
is in preparation of SFF cleanup.

This patch strictly moves stuff around and as such doesn't cause any
functional difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
21572ea58a libata: drop ata_dev_select() from ata_dev_read_id
There is no reason to issue device select in read_id, it will be done
by ops->qc_issue() when IDENTIFY[_PACKET] is issued via
ata_exec_internal().

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
a1efdaba2d libata: make reset related methods proper port operations
Currently reset methods are not specified directly in the
ata_port_operations table.  If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods.  It's done this way for two reasons.

First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.

Second, as ->error_handler uses those reset methods, it can get
confusing.  ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.

Now that ops table uses inheritance, the first problem doesn't exist
anymore.  The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks.  In fact, there currently is no driver which actually
modifies error handling behavior.  Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH.  I don't think making ops layering strict has
any noticeable benefit.

This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops.  Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.

* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
  aren't accessible.  sata_promise doesn't need to use separate
  error_handlers for PATA and SATA anymore.

* softreset is broken for sata_inic162x and sata_sx4.  As libata now
  always prefers hardreset, this doesn't really matter but the ops are
  forced to NULL using ATA_OP_NULL for documentation purpose.

* pata_hpt374 needs to use different prereset for the first and second
  PCI functions.  This used to be done by branching from
  hpt374_error_handler().  The proper way to do this is to use
  separate ops and port_info tables for each function.  Converted.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:18 -04:00
Tejun Heo
9594719362 libata: kill port_info->sht and ->irq_handler
libata core layer doesn't care about sht or ->irq_handler.  Those are
only of interest to the LLD during initialization.  This is confusing
and has caused several drivers to have duplicate unused initializers
for these fields.

Currently only sata_nv uses these fields.  Make sata_nv use
->private_data, which is supposed to carry LLD-specific information,
instead and kill ->sht and ->irq_handler.  nv_pi_priv structure is
defined and struct literals are used to initialize private_data.
Notational overhead is negligible.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo
887125e374 libata: stop overloading port_info->private_data
port_info->private_data is currently used for two purposes - to record
private data about the port_info or to specify host->private_data to
use when allocating ata_host.

This overloading is confusing and counter-intuitive in that
port_info->private_data becomes host->private_data instead of
port->private_data.  In addition, port_info and host don't correspond
to each other 1-to-1.  Currently, the first non-NULL
port_info->private_data is used.

This patch makes port_info->private_data just be what it is -
private_data for the port_info where LLD can jot down extra info.
libata no longer sets host->private_data to the first non-NULL
port_info->private_data, @host_priv argument is added to
ata_pci_init_one() instead.  LLDs which use ata_pci_init_one() can use
this argument to pass in pointer to host private data.  LLDs which
don't should use init-register model anyway and can initialize
host->private_data directly.

Adding @host_priv instead of using init-register model for LLDs which
use ata_pci_init_one() is suggested by Alan Cox.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
2008-04-17 15:44:17 -04:00
Tejun Heo
1bd5b715a3 libata: make ata_pci_init_one() not use ops->irq_handler and pi->sht
ata_pci_init_one() is the only function which uses ops->irq_handler
and pi->sht.  Other initialization functions take the same information
as arguments.  This causes confusion and duplicate unused entries in
structures.

Make ata_pci_init_one() take sht as an argument and use ata_interrupt
implicitly.  All current users use ata_interrupt and if different irq
handler is necessary open coding ata_pci_init_one() using
ata_prepare_sff_host() and ata_activate_sff_host can be done under ten
lines including error handling and driver which requires custom
interrupt handler is likely to require custom initialization anyway.

As ata_pci_init_one() was the last user of ops->irq_handler, this
patch also kills the field.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo
029cfd6b74 libata: implement and use ops inheritance
libata lets low level drivers build ata_port_operations table and
register it with libata core layer.  This allows low level drivers
high level of flexibility but also burdens them with lots of
boilerplate entries.

This becomes worse for drivers which support related similar
controllers which differ slightly.  They share most of the operations
except for a few.  However, the driver still needs to list all
operations for each variant.  This results in large number of
duplicate entries, which is not only inefficient but also error-prone
as it becomes very difficult to tell what the actual differences are.

This duplicate boilerplates all over the low level drivers also make
updating the core layer exteremely difficult and error-prone.  When
compounded with multi-branched development model, it ends up
accumulating inconsistencies over time.  Some of those inconsistencies
cause immediate problems and fixed.  Others just remain there dormant
making maintenance increasingly difficult.

To rectify the problem, this patch implements ata_port_operations
inheritance.  To allow LLDs to easily re-use their own ops tables
overriding only specific methods, this patch implements poor man's
class inheritance.  An ops table has ->inherits field which can be set
to any ops table as long as it doesn't create a loop.  When the host
is started, the inheritance chain is followed and any operation which
isn't specified is taken from the nearest ancestor which has it
specified.  This operation is called finalization and done only once
per an ops table and the LLD doesn't have to do anything special about
it other than making the ops table non-const such that libata can
update it.

libata provides four base ops tables lower drivers can inherit from -
base, sata, pmp, sff and bmdma.  To avoid overriding these ops
accidentaly, these ops are declared const and LLDs should always
inherit these instead of using them directly.

After finalization, all the ops table are identical before and after
the patch except for setting .irq_handler to ata_interrupt in drivers
which didn't use to.  The .irq_handler doesn't have any actual effect
and the field will soon be removed by later patch.

* sata_sx4 is still using old style EH and currently doesn't take
  advantage of ops inheritance.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo
68d1d07b51 libata: implement and use SHT initializers
libata lets low level drivers build scsi_host_template and register it
to the SCSI layer.  This allows low level drivers high level of
flexibility but also burdens them with lots of boilerplate entries.

This patch implements SHT initializers which can be used to initialize
all the boilerplate entries in a sht.  Three variants of them are
implemented - BASE, BMDMA and NCQ - for different types of drivers.
Note that entries can be overriden by putting individual initializers
after the helper macro.

All sht tables are identical before and after this patch.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo
6bd99b4e09 libata: normalize port_info, port_operations and sht tables
Over the time, port info, ops and sht structures developed quite a bit
of inconsistencies.  This patch updates drivers.

* Enable/disable_pm callbacks added to all ahci ops tables.

* Every driver for SFF controllers now uses ata_sff_port_start()
  instead of ata_port_start() unless the driver has custom
  implementation.

* Every driver for SFF controllers now uses ata_pci_default_filter()
  unless the driver has custom implementation.

* Removed an odd port_info->sht initialization from ata_piix.c.
  Likely a merge byproduct.

* A port which has ATA_FLAG_SATA set doesn't need to set cable_detect
  to ata_cable_sata().  Remove it from via and mv port ops.

* Some drivers had unnecessary .max_sectors initialization which is
  ignored and was missing .slave_destroy callback.  Fixed.

* Removed unnecessary sht initializations port_info's.

* Removed onsolete scsi device suspend/resume callbacks from
  pata_bf54x.

* No reason to set ata_pci_default_filter() and bmdma functions for
  PIO-only drivers.  Remove those callbacks and replace
  ata_bmdma_irq_clear with ata_noop_irq_clear.

* pata_platform sets port_start to ata_dummy_ret0.  port_start can
  just be set to NULL.

* sata_fsl supports NCQ but was missing qc_defer.  Fixed.

* pata_rb600_cf implements dummy port_start.  Removed.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo
358f9a77a6 libata: implement and use ata_noop_irq_clear()
->irq_clear() is used to clear IRQ bit of a SFF controller and isn't
useful for drivers which don't use libata SFF HSM implementation.
However, it's a required callback and many drivers implement their own
noop version as placeholder.  This patch implements ata_noop_irq_clear
and use it to replace those custom placeholders.

Also, SFF drivers which don't support BMDMA don't need to use
ata_bmdma_irq_clear().  It becomes noop if BMDMA address isn't
initialized.  Convert them to use ata_noop_irq_clear().

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo
f08048e945 libata: PCI device should be powered up before being accessed
PCI device should be powered up or powered up before its PCI regsiters
are accessed.  Although PCI configuration register access is allowed
in D3hot, PCI device is free to reset its status when transiting from
D3hot to D0 causing configuration data to change.

Many libata SFF drivers which use ata_pci_init_one() read and update
configuration registers before calling ata_pci_init_one() which
enables the PCI device.  Also, in resume paths, some drivers access
registers without resuming the PCI device.

This patch adds a call to pcim_enable_device() in init path if
register is accessed before calling ata_pci_init_one() and make resume
paths first resume PCI devices, access PCI configuration regiters then
resume ATA host.

While at it...

* cmd640 was strange in that it set ->resume even when CONFIG_PM is
  not.  This is by-product of minimal build fix.  Updated.

* In cs5530, Don't BUG() on reinit failure.  Just whine and fail
  resume.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo
b558edddb1 libata: kill ata_ehi_schedule_probe()
ata_ehi_schedule_probe() was created to hide details of link-resuming
reset magic.  Now that all the softreset workarounds are gone,
scheduling probe is very simple - set probe_mask and request RESET.
Kill ata_ehi_schedule_probe() and open code it.  This also increases
consistency as ata_ehi_schedule_probe() couldn't cover individual
device probings so they were open-coded even when the helper existed.

While at it, define ATA_ALL_DEVICES as mask of all possible devices on
a link and always use it when requesting probe on link level for
simplicity and consistency.  Setting extra bits in the probe_mask
doesn't hurt anybody.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo
8cebf274dd libata: kill ATA_LFLAG_SKIP_D2H_BSY
Some controllers can't reliably record the initial D2H FIS after SATA
link is brought online for whatever reason.  Advanced controllers
which don't have traditional TF register based interface often have
this problem as they don't really have the TF registers to update
while the controller and link are being initialized.

SKIP_D2H_BSY works around the problem by skipping the wait for device
readiness before issuing SRST, so for such controllers libata issues
SRST blindly and hopes for the best.

Now that libata defaults to hardreset, this workaround is no longer
necessary.  For controllers which have support for hardreset, SRST is
never issued by itself.  It is only issued as follow-up SRST for
device classification and PMP initialization, so there's no need to
wait for it from prereset.

Kill ATA_LFLAG_SKIP_D2H_BSY.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo
672b2d65ba libata: kill ATA_EHI_RESUME_LINK
ATA_EHI_RESUME_LINK has two functions - promote reset to hardreset if
ATA_LFLAG_HRST_TO_RESUME is set and preventing EH from shortcutting
reset action when probing is requested.  The former is gone now and
the latter can easily be achieved by making EH to perform at least one
reset if reset is requested, which also makes more sense than
depending on RESUME_LINK flag.

As ATA_EHI_RESUME_LINK was the only EHI reset modifier, this also
kills reset modifier handling.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo
d692abd92f libata: kill ATA_LFLAG_HRST_TO_RESUME
Now that hardreset is the preferred method of resetting, there's no
need for ATA_LFLAG_HRST_TO_RESUME flag.  Kill it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:15 -04:00
Tejun Heo
cf48062658 libata: prefer hardreset
When both soft and hard resets are available, libata preferred
softreset till now.  The logic behind it was to be softer to devices;
however, this doesn't really help much.  Rationales for the change:

* BIOS may freeze lock certain things during boot and softreset can't
  unlock those.  This by itself is okay but during operation PHY event
  or other error conditions can trigger hardreset and the device may
  end up with different configuration.

  For example, after a hardreset, previously unlockable HPA can be
  unlocked resulting in different device size and thus revalidation
  failure.  Similar condition can occur during or after resume.

* Certain ATAPI devices require hardreset to recover after certain
  error conditions.  On PATA, this is done by issuing the DEVICE RESET
  command.  On SATA, COMRESET has equivalent effect.  The problem is
  that DEVICE RESET needs its own execution protocol.

  For SFF controllers with bare TF access, it can be easily
  implemented but more advanced controllers (e.g. ahci and sata_sil24)
  require specialized implementations.  Simply using hardreset solves
  the problem nicely.

* COMRESET initialization sequence is the norm in SATA land and many
  SATA devices don't work properly if only SRST is used.  For example,
  some PMPs behave this way and libata works around by always issuing
  hardreset if the host supports PMP.

  Like the above example, libata has developed a number of mechanisms
  aiming to promote softreset to hardreset if softreset is not going
  to work.  This approach is time consuming and error prone.

  Also, note that, dependingon how you read the specs, it could be
  argued that PMP fan-out ports require COMRESET to start operation.
  In fact, all the PMPs on the market except one don't work properly
  if COMRESET is not issued to fan-out ports after PMP reset.

* COMRESET is an integral part of SATA connection and any working
  device should be able to handle COMRESET properly.  After all, it's
  the way to signal hardreset during reboot.  This is the most used
  and recommended (at least by the ahci spec) method of resetting
  devices.

So, this patch makes libata prefer hardreset over softreset by making
the following changes.

* Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever
  ATA_EH_{SOFT|HARD}RESET used to be used.  ATA_EH_{SOFT|HARD}RESET is
  now only used to tell prereset whether soft or hard reset will be
  issued.

* Strip out now unneeded promote-to-hardreset logics from
  ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and
  other places.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:15 -04:00
Jeff Garzik
36b30ea940 [netdrvr] forcedeth: internal simplifications; changelog removal
* remove changelog from source; its kept in git repository

* consolidate descriptor version tests using nv_optimized()

* consolidate NIC DMA start, stop and drain into
  nv_start_txrx(), nv_stop_txrx(), nv_drain_txrx()

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:31:33 -04:00
Paul Gortmaker
cac1f3c8a8 phylib: factor out get_phy_id from within get_phy_device
We were already doing what amounts to a get_phy_id from within
get_phy_device, and rather than duplicate this for the TBIPA
probing, we might as well just factor it out and make it available
instead.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:31:33 -04:00
Paul Gortmaker
b1394f961a PHY: add BCM5464 support to broadcom PHY driver
The BCM5464 can be used with the current broadcom PHY driver
by just adding the appropriate chip ID and using the existing
support within.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:31:32 -04:00
Dan Noe
d96a51f6b8 cxgb3: Fix __must_check warning with dev_dbg.
Fix the warning:
drivers/net/cxgb3/cxgb3_main.c: In function ‘offload_open’:
drivers/net/cxgb3/cxgb3_main.c:936: warning: ignoring return value of
 ‘sysfs_create_group’, declared with attribute warn_unused_result

Now the return value is checked; if sysfs_create_group() returns failure,
a warning is printed using dev_dbg, and the code continues as before.  Use
of dev_dbg ensures printk is not needlessly included unless desired for
debugging.

Signed-off-by: Dan Noe <dpn@isomerica.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:31:32 -04:00
Atsushi Nemoto
10e05f78c5 tc35815: Statistics cleanup
On Sat, 12 Apr 2008 05:00:49 -0400, Jeff Garzik <jeff@garzik.org> wrote:
> applied 1-6

Thanks.

Could you apply this too, or hopufully fold into Andy Fleming's "phy:
Change mii_bus id field to a string" patch (commit c69fedae) ?

------------------------------------------------------
Subject: [PATCH] tc35815: build fix

Fix build failure caused by Andy Fleming's "phy: Change mii_bus id
field to a string" patch.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:31:31 -04:00
Sergei Shtylyov
703bb99ca7 natsemi: fix MMIO for PPC 44x platforms
The driver stores the PCI resource address into 'unsigned long' variable before
calling ioremap()  on it. This warrants a kernel oops when the registers are
accessed on PPC 44x platforms which (being 32-bit) have PCI memory space mapped
beyond 4 GB.

The arch/ppc/ kernel has a fixup in ioremap() that creates an illusion of the
PCI memory resources are mapped below 4 GB, but arch/powerpc/ code got rid of
this trick, having instead CONFIG_RESOURCES_64BIT enabled.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:31:31 -04:00
Jason Wessel
974460c5bf kgdb: allow static kgdbts boot configuration
This patch adds in the ability to compile the kgdb internal test
string into the kernel so as to run the tests at boot without changing
the kernel boot arguments.  This patch also changes all the error
paths to invoke WARN_ON(1) which will emit the line number of the file
and dump the kernel stack when an error occurs.

You can disable the tests in a kernel that is built this way
using "kgdbts="

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-04-17 20:05:43 +02:00
Andrew Morton
4a1b5502d4 kgdb: Kconfig fix
ERROR: "uart_parse_options" [drivers/serial/serial_core.ko] undefined!

Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-04-17 20:05:42 +02:00
Jason Wessel
e8d31c204e kgdb: add kgdb internal test suite
This patch adds regression tests for testing the kgdb core and arch
specific implementation.

The kgdb test suite is designed to be built into the kernel and not as
a module because it uses a number of low level kernel and kgdb
primitives which should not be exported externally.

The kgdb test suite is designed as a KGDB I/O module which
simulates the communications that a debugger would have with kgdb.
The tests are broken up in to a line by line and referenced here as
a "get" which is kgdb requesting input and "put" which is kgdb
sending a response.

The kgdb suite can be invoked from the kernel command line
arguments system or executed dynamically at run time.  The test
suite uses the variable "kgdbts" to obtain the information about
which tests to run and to configure the verbosity level.  The
following are the various characters you can use with the kgdbts=
line:

When using the "kgdbts=" you only choose one of the following core
test types:
A = Run all the core tests silently
V1 = Run all the core tests with minimal output
V2 = Run all the core tests in debug mode

You can also specify optional tests:
N## = Go to sleep with interrupts of for ## seconds
      to test the HW NMI watchdog
F## = Break at do_fork for ## iterations
S## = Break at sys_open for ## iterations

NOTE: that the do_fork and sys_open tests are mutually exclusive.

To invoke the kgdb test suite from boot you use a kernel start
argument as follows:
	kgdbts=V1 kgdbwait
Or if you wanted to perform the NMI test for 6 seconds and do_fork
test for 100 forks, you could use:
	kgdbts=V1N6F100 kgdbwait

The test suite can also be invoked at run time with:
echo kgdbts=V1N6F100 > /sys/module/kgdbts/parameters/kgdbts
Or as another example:
echo kgdbts=V2 > /sys/module/kgdbts/parameters/kgdbts

When developing a new kgdb arch specific implementation or
using these tests for the purpose of regression testing,
several invocations are required.

1) Boot with the test suite enabled by using the kernel arguments
      "kgdbts=V1F100 kgdbwait"
   ## If kgdb arch specific implementation has NMI use
      "kgdbts=V1N6F100

2) After the system boot run the basic test.
echo kgdbts=V1 > /sys/module/kgdbts/parameters/kgdbts

3) Run the concurrency tests.  It is best to use n+1
   while loops where n is the number of cpus you have
   in your system.  The example below uses only two
   loops.

## This tests break points on sys_open
while [ 1 ] ; do find / > /dev/null 2>&1 ; done &
while [ 1 ] ; do find / > /dev/null 2>&1 ; done &
echo kgdbts=V1S10000 > /sys/module/kgdbts/parameters/kgdbts
fg # and hit control-c
fg # and hit control-c
## This tests break points on do_fork
while [ 1 ] ; do date > /dev/null ; done &
while [ 1 ] ; do date > /dev/null ; done &
echo kgdbts=V1F1000 > /sys/module/kgdbts/parameters/kgdbts
fg # and hit control-c

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-04-17 20:05:42 +02:00
Jason Wessel
84b5ae1521 kgdb: kgdboc pl011 I/O module
Implement the serial polling hooks for the pl011 uart for use with
kgdboc.

This patch was specifically tested on the ARM Versatile AB reference
platform.

[ mingo@elte.hu: minor cleanups. ]

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-04-17 20:05:39 +02:00
Jason Wessel
c191e5ad6b kgdb: fix kgdboc dynamic module configuration
Fix the run time configuration of kgdboc such that it does not default
to 9600 baud if you use the "echo" command to configure the sysfs
module paramater.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-04-17 20:05:38 +02:00
Jason Wessel
f2d937f3bf consoles: polling support, kgdboc
polled console handling support, to access a console in an irq-less
way while in debug or irq context.

absolutely zero impact as long as CONFIG_CONSOLE_POLL is disabled.
(which is the default)

[ jan.kiszka@siemens.com: lots of cleanups ]
[ mingo@elte.hu: redesign, splitups, cleanups. ]

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
2008-04-17 20:05:37 +02:00
Adrian Bunk
0e4ff797d7 [SCSI] qla1280: remove version check
There's no point for an in-kernel driver to check whether it's compiled
under kernel < 2.6.0 .

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-17 12:59:21 -05:00
Al Viro
17b7a8de3b [SCSI] libsas: fix endianness bug in sas_ata
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-17 12:57:17 -05:00
Martin Peschke
ee95a16d39 [SCSI] zfcp: fix compiler warning caused by poking inside new semaphore (linux-next)
as seen in linux-next tree:

drivers/s390/scsi/zfcp_dbf.c: In function ‘zfcp_rec_dbf_event_thread’:
drivers/s390/scsi/zfcp_dbf.c:697: warning: passing argument 1 of ‘atomic_read’
 from incompatible pointer type

Caused by recent git commit:

commit 348447e857
Author: Martin Peschke <mp3@de.ibm.com>
Date:   Thu Mar 27 14:22:01 2008 +0100

    [SCSI] zfcp: Add trace records for recovery thread and its queues

We are not supposed to poke inside semaphore.

Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-17 12:56:49 -05:00
Sascha Hauer
3a8daaa49f [ARM] 4999/1: <IMX UART>: fix membase
The membase field in struct uart_port should be the the physical
address. This patch fixes it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17 16:22:22 +01:00
Sascha Hauer
3d454446e2 [ARM] 4998/1: <IMX UART>: do not use hardcoded io space size
Do not use hardcoded io space size. Instead use the information provided
by the resource.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17 16:22:21 +01:00
Sascha Hauer
789d52589a [ARM] 4996/1: <IMX UART>: do not enable tx empty interrupt on startup
We are not interested in tranceiver empty interrupts until we actually
sent a buffer.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17 16:18:22 +01:00
Sascha Hauer
0d3c3938ff [ARM] 4995/1: <IMX UART>: Do not use URXD_CHARRDY for polling
Do not use the URXD_CHARRDY bit for polling for new characters. This works
on i.MX1, but on MX31 the datasheet states that this bit should not be
used for polling. On MX27 it is even worse, here we get a bus error when
we access the read FIFO when no character is present.
Instead, use USR2_RDR (receive data ready) bit.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17 16:18:20 +01:00
Sascha Hauer
864eeed051 [ARM] 4994/1: <IMX UART>: Move error handling into execution path
Move the error handling code for erroneous receive characters into
execution path. This makes the code more readable and the compiler
should know how to optimize this, right?

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17 16:18:19 +01:00
Sascha Hauer
8c9915bf31 [ARM] 4993/1: <IMX UART>: Trivial: Remove unused defines
This patch removes the unused defines NR_PORTS and IMX_ISR_PASS_LIMIT in
the imx serial driver.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17 16:18:18 +01:00
Andrew Victor
2f036ac63e [ARM] 4980/1: [AT91] emQbit ECB_AT91 board support
Support for the emQbit ECB_AT91 board.
  <http://wiki.emqbit.com/free-ecb-at91>

Original patch from Nelson Castillo.

Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-17 15:55:51 +01:00
Matthew Wilcox
f1241c87a1 Add down_timeout and change ACPI to use it
ACPI currently emulates a timeout for semaphores with calls to
down_trylock and sleep.  This produces horrible behaviour in terms of
fairness and excessive wakeups.  Now that we have a unified semaphore
implementation, adding a real down_trylock is almost trivial.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
2008-04-17 10:42:46 -04:00
Anton Vorontsov
d4a32fe40a [POWERPC] fsl_elbc_nand: factor out localbus defines
This is needed to support other localbus peripherals, such as
NAND on FSL UPM.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:38 -05:00
Anton Vorontsov
56626f335b [POWERPC] QE: UCC nodes cleanup
- get rid of `model = "UCC"' in the ucc nodes
  It isn't used anywhere, so remove it. If we'll ever need something
  like this, we'll use compatible property instead.
- replace last occurrences of device-id with cell-index.
  Drivers are modified for backward compatibility's sake.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:38 -05:00
Laurent Pinchart
d464df2667 [POWERPC] cpm_uart: Allocate DPRAM memory for SMC ports on CPM2-based platforms.
This patch allocates parameter RAM for SMC serial ports without relying on
previous initialisation by a boot loader or a wrapper layer.

SMC parameter RAM on CPM2-based platforms can be allocated anywhere in the
general-purpose areas of the dual-port RAM. The current code relies on the
boot loader to allocate a section of general-purpose CPM RAM and gets the
section address from the device tree.

This patch modifies the device tree address usage to reference the SMC
parameter RAM base pointer instead of a pre-allocated RAM section and
allocates memory from the CPM dual-port RAM when initialising the SMC port.
CPM1-based platforms are not affected.

Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:36 -05:00
Martin Schwidefsky
ca68305bf3 [S390] Remove code duplication from monreader / dcssblk.
Move the function that prints the segment warning messages found in the
monreader driver and the dcssblk driver to the extmem base code.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:47:07 +02:00
Felix Beck
1749a81d62 [S390] zcrypt: Comments and kernel-doc cleanup
Comments, which suggested to be kernel-doc but were not in the right
formatting, have been corrected. Additionally some minor cleanup in
the comments has been done.

Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:47:06 +02:00
Heiko Carstens
a806170e29 [S390] Fix a lot of sparse warnings.
Most noteable part of this commit is the new local header file entry.h
which contains all the function declarations of functions that get only
called from asm code or are arch internal. That way we can avoid extern
declarations in C files.
This is more or less the same that was done for sparc64.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:47:06 +02:00
Heiko Carstens
5a62b19219 [S390] Convert s390 to GENERIC_CLOCKEVENTS.
This way we get rid of s390's NO_IDLE_HZ and use the generic dynticks
variant instead. In addition we get high resolution timers for free.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:47:05 +02:00
Heiko Carstens
43ca5c3a1c [S390] Convert monitor calls to function calls.
Remove the program check generating monitor calls and use function
calls instead. Theres is no real advantage in using monitor calls,
but they do make debugging harder, because of all the program checks
it generates.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:47:05 +02:00
Ursula Braun
e177685628 [S390] qdio (new feature): enhancing info-retrieval from QDIO-adapters
Next generation of OSA adapters allows retrieval of further self-describing
infos. This is the preparational infrastructure patch for further exploitation
in the qeth driver.

Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:47:04 +02:00
Harvey Harrison
2a2cf6b186 [S390] replace remaining __FUNCTION__ occurrences
__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:47:04 +02:00
Ralph Wuerthner
2f7c8bd6dc [S390] zcrypt: add support for large random numbers
This patch allows user space applications to access large amounts of
truly random data. The random data source is the build-in hardware
random number generator on the CEX2C cards.

Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:47:02 +02:00
Ralph Wuerthner
893f112866 [S390] hw_random: allow rng_dev_read() to return hardware errors.
The api for hardware random number generators is currently limited to
devices that never fail. If the hardware is registered as a source for
random numbers it has to work. This prevents the use of i/o based
random number devices where the i/o might fail.

Add a check for errors after the read from a hardware random number device.

This patch is required to support large random numbers retrieved
from the CEX2C cards on System z.

Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:47:02 +02:00
Martin Schwidefsky
cbce70e687 [S390] Add new fields for System z10 to /proc/sysinfo
Add permanent and temporary model capacity and the corresponding
capacity value fields for the three capacity identifiers to the
output of /proc/sysinfo.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:47:01 +02:00
Christian Borntraeger
aa24f7f08b [S390] KVM preparation: split sysinfo definitions for kvm use
drivers/s390/sysinfo.c uses the store system information intruction to query
the system about information of the machine, the LPAR and additional
hypervisors. KVM has to implement the host part for this instruction.

To avoid code duplication, this patch splits the common definitions from
sysinfo.c into a separate header file include/asm-s390/sysinfo.h for KVM use.

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:47:00 +02:00
Stefan Haberland
f60c768c38 [S390] dasd: add sim handling.
Now the system reports system information messages (SIM) to the user.
The System Reference Code (SRC) which is reported to the user gives
the abbility to lookup the reason of the SIM online in the
documentation of the storage server.

Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:47:00 +02:00
Frank Munzert
a695f16729 [S390] vmur: Use wait queue instead of mutex to serialize open
If user space opens a unit record device node then vmur is leaving the kernel
with lock open_mutex still held to prevent other processes from opening the
device simultaneously. This causes lockdep to complain about a lock held when
returning to user space.
Now the mutex is replaced by a wait queue to serialize device open.

Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:46:59 +02:00
Michael Holzheu
92bf435f38 [S390] tape: duplicate sysfs filename when setting tape device online
When a tape device is set online, offline and online again, the following
error message is printed on the console: "sysfs: duplicate filename
'non-rewinding' can not be created". The reason is that when setting a
device online, the tape driver creates a sysfs symlink from the tape device
to the tape class device. Unfortunately the symlink is not removed
correctly, when the device is set offline. Instead of passing the
tape device object to sysfs_remove_link, the class device object is used.
This patch fixes this problem and uses the correct tape device object now.

Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:46:59 +02:00
Stefan Haberland
00966c0a5b [S390] dasd: use GFP_DMA for fba private data allocation
allocating dasd_fba_private without GFP_DMA results in IO error
during read device characteristics of a FBA disk

Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:46:58 +02:00
Ursula Braun
35b58b028d [S390] qdio: Unrecognized inbound traffic if many FCP devices are online
Problem:
Usually every FCP device has its own indicator field the adapter
uses to signal outstanding work. Once a certain limit of devices
is reached, a common indicator field is used. In certain scenarios
qdio resets this common indicator field, but handles only part of
the FCP-devices sharing the common indicator field. Thus inbound
traffic on the non-processed shared FCP-devices is not recognized
immediately.

Solution:
Make sure common indicator field is reset only, if all FCP-devices
sharing the indicator are processed.

Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:46:58 +02:00
Heiko Carstens
d1e23375bf [S390] sclp: Get rid of in_atomic() use.
Reintroduces in_interrupt() check in sclp_tty code. Add may_schedule
parameter to vt220 write function, so we can let the write function
know if it may schedule or not. So we disallow scheduling for all
console calls and may allow them for tty calls.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:46:58 +02:00
Michael Ernst
8284fb19ef [S390] cio: fix parallel cm_enable processing.
It is now possible to trigger cm_enable processing several times in
parallel without causing a kernel panic.

Signed-off-by: Michael Ernst <mernst@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:46:57 +02:00
Cornelia Huck
fe6173d9b3 [S390] cio: Trigger verification on device/path not operational.
Currently, we don't do much on no path or no device situations during
normal user I/O, since we rely on reports regarding those events by
the machine. If we trigger a path verification to bring our device
state up-to-date, we (a) may recover from path failures earlier and
(b) better handle situations where the hardware/hypervisor doesn't
give us enough notifications.

Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:46:57 +02:00
Cornelia Huck
22806dc1a8 [S390] cio: Fix race for "fast" path gone/path back situations.
Make sure we wait for previous evaluations triggered by path state
changes to have settled before we manipulate path states again.

Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:46:57 +02:00
Josef 'Jeff' Sipek
08a8a0c59e [S390] dasd: fix double elevator_exit call when deadline iosched fails to load
I compiled the kernel without deadline, and the dasd code exits the old
scheduler (CFQ), fails to load the new one (deadline), and then things just
hang - with one of these (sorry about the weird chars - I copy & pasted it
from a 3270 console):

dasd(eckd): 0.0.0151: 3390/0A(CU:3990/01) Cyl:3338 Head:15 Sec:224
------------ cut here ------------
Badness at kernel/mutex.c:134
Modules linked in: dasd_eckd_mod dasd_mod
CPU: 0 Not tainted 2.6.25-rc3 
Process exe (pid: 538, task: 000000000d172000, ksp: 000000000d21ef88)
Krnl PSW : 0404000180000000 000000000022fb5c (mutex_lock_nested+0x2a4/0x2cc)
           R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:0 PM:0 EA:3
Krnl GPRS: 0000000000024218 000000000076fc78 0000000000000000 000000000000000f
           000000000022f92e 0000000000449898 000000000f921c00 000003e000162590
           00000000001539c4 000000000d172000 070000007fffffff 000000000d21f400
           000000000f8f2560 00000000002413f8 000000000022fb44 000000000d21f400
Krnl Code: 000000000022fb50: bf2f1000           icm     %r2,15,0(%r1)
           000000000022fb54: a774fef6           brc     7,22f940
           000000000022fb58: a7f40001           brc     15,22fb5a
          >000000000022fb5c: a7f4fef2           brc     15,22f940
           000000000022fb60: c0e5fffa112a       brasl   %r14,171db4
           000000000022fb66: 1222               ltr     %r2,%r2
           000000000022fb68: a784fedb           brc     8,22f91e
           000000000022fb6c: c010002a0086       larl    %r1,76fc78
Call Trace:
(<000000000022f92e> mutex_lock_nested+0x76/0x2cc)
 <00000000001539c4> elevator_exit+0x38/0x80
 <0000000000156ffe> blk_cleanup_queue+0x62/0x7c
 <000003e0001d5414> dasd_change_state+0xe0/0x8ec
 <000003e0001d5cae> dasd_set_target_state+0x8e/0x9c
 <000003e0001d5f74> dasd_generic_set_online+0x160/0x284
 <000003e00011e83a> dasd_eckd_set_online+0x2e/0x40
 <0000000000199bf4> ccw_device_set_online+0x170/0x2c0
 <0000000000199d9e> online_store_recog_and_online+0x5a/0x14c
 <000000000019a08a> online_store+0xbe/0x2ec
 <000000000018456c> dev_attr_store+0x38/0x58
 <000000000010efbc> sysfs_write_file+0x130/0x190
 <00000000000af582> vfs_write+0xb2/0x160
 <00000000000afc7c> sys_write+0x54/0x9c
 <0000000000025e16> sys32_write+0x2e/0x50
 <0000000000024218> sysc_noemu+0x10/0x16
 <0000000077e82bd2> 0x77e82bd2

Set elevator pointer to NULL in order to avoid double elevator_exit
calls when elevator_init call for deadline iosched fails.
Also make sure the dasd device driver depends on IOSCHED_DEADLINE so
the default IO scheduler of the dasd driver is present.

Signed-off-by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:46:55 +02:00
Erez Zilber
0a22ab92f5 IB/iser: Don't change itt endianness
The itt field in struct iscsi_data is not defined with any particular
endianness.  open-iscsi should use it as-is without byte-swapping it.
This fixes sparse warnings coming from doing ntohl(hdr->itt).

Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:35 -07:00
Jack Morgenstein
068c4ea1bb IB/mlx4: Update module version and release date
The mlx4_ib driver is stable enough for production use, so bump the
version number to 1.0 to indicate this.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:35 -07:00
Roland Dreier
9fdd5e5bf6 IPoIB: Handle case when P_Key is deleted and re-added at same index
If a P_Key is deleted and then re-added at the same index, then IPoIB
gets confused because __ipoib_ib_dev_flush() only checks whether the
index is the same without checking whether the P_Key was present, so
the interface is stopped when the P_Key is deleted, but the event when
the P_Key is re-added gets ignored and the interface never gets
restarted.

Also, switch to using ib_find_pkey() instead of ib_find_cached_pkey()
everywhere in IPoIB, since none of the places that look for P_Keys are
in a fast path or in non-sleeping context, and in general we want to
kill off the whole caching infrastructure eventually.  This also fixes
consistency problems caused because some IPoIB queries were cached and
some were uncached during the window where the cache was not updated.

Thanks to Venkata Subramonyam <vsubramo@cisco.com> for debugging this
problem and testing this fix.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:35 -07:00
Erez Zilber
d97c51707d IB/iser: Release connection resources on RDMA_CM_EVENT_DEVICE_REMOVAL event
When a RDMA_CM_EVENT_DEVICE_REMOVAL event is raised, iSER should
release the connection resources.

This is necessary when the IB HCA module is unloaded while open-iscsi
is still running.  Currently, iSER just BUG()s.

Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:35 -07:00
Eli Cohen
4ff08a76bc IB/mlx4: Fix incorrect comment
mlx4 hardware does not support external DDR memory.  Moreover, UAR
area (BAR 2) can change depending on FW version.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:35 -07:00
Eli Cohen
4dc51b3258 IB/mlx4: Fix race when detaching a QP from a multicast group
When detaching the last QP from an MCG entry, we need to make
sure that at any time, there will be no entry with zero number of
QPs which is linked to the list of the MCGs of the corresponding
hash index.  So don't write back the MCG entry if we are removing the
last QP; just unlink the entry.

Also, remove an unnecessary MCG read when attaching a QP requires
allocation of a new entry in the AMGM.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:35 -07:00
Stefan Roscher
c83b5b1cb2 IB/ehca: Support all ibv_devinfo values in query_device() and query_port()
Also, introduce a few inline helper functions to make the code more readable.

Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:35 -07:00
Roland Dreier
4cd1e5eb3c RDMA/nes: Free IRQ before killing tasklet
Move the free_irq() call in nes_remove() to before the tasklet_kill();
otherwise there is a window after tasklet_kill() where a new interrupt
can be handled and reschedule the tasklet, leading to a use-after-free
crash.

Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:34 -07:00
Jack Morgenstein
940801b27e IB/mthca: Update module version and release date
The ib_mthca driver has been stable for a while, so bump the version
number to 1.0 to indicate this.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:34 -07:00
Dotan Barak
0df6703095 IB/mlx4: Update QP state if query QP succeeds
If the QP was moved to another state (such as SQE) by the hardware,
then after this change the user won't have to set the IBV_QP_CUR_STATE
mask in order to execute modify QP in order to recover from this state.

Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:34 -07:00
Dotan Barak
5121df3ae4 IB/mthca: Update QP state if query QP succeeds
If the QP was moved to another state (such as SQE) by the hardware,
then after this change the user won't have to set the IBV_QP_CUR_STATE
mask in order to execute modify QP in order to recover from this state.

Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:34 -07:00
Tom Tucker
9285faa1e7 RDMA/amso1100: Add check for NULL reply_msg in c2_intr()
Fix a place where we might dereference a NULL pointer; this fixes
Coverity CID 1392.  On inspection I also found a place where we could
attempt to kmem_cache_free() a NULL pointer, so fix this too.

Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:34 -07:00
Vladimir Sokolovsky
bbf8eed1a0 IB/mlx4: Add support for resizing CQs
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:33 -07:00
Eli Cohen
3fdcb97f0b IB/mlx4: Add support for modifying CQ moderation parameters
Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:33 -07:00
Eli Cohen
28d52b3cd8 IPoIB: Support modifying IPoIB CQ event moderation
This can be used to tune at run time the parameters controlling the
event (interrupt) generation rate and thus reduce the overhead
incurred by handling interrupts resulting in better throughput.  Since
IPoIB uses a single CQ for both RX and TX, RX is chosen to dictate
configuration for both RX and TX.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:33 -07:00
Eli Cohen
2dd5716227 IB/core: Add support for modify CQ
Add support for modifying CQ parameters for controlling event
generation moderation.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:33 -07:00
Eli Cohen
82c24c18af IPoIB: Add basic ethtool support
Just add the infrastructure so we can add functionality later.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:32 -07:00
Jack Morgenstein
9b1f38515c mlx4_core: Increase max number of QPs to 128K
With the advent large clusters which utilize multicore hosts, 64K QPs
is not enough.  We should increase the default maximum for QPs to 128K.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:32 -07:00