Most protocol-specific pointers in struct net_device are under
a respective ifdef. Wireless is the notable exception. Since
there's a sizable number of custom-built kernels for datacenter
workloads which don't build wireless it seems reasonable to
ifdefy those pointers as well.
While at it move IPv4 and IPv6 pointers up, those are special
for obvious reasons.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> # ieee802154
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An error code returned by devm_clk_get() might have other meanings than
"This clock doesn't exist". So use devm_clk_get_optional() and handle
all remaining errors as fatal.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII mode can be enable from dp83822 straps, and also writing bit 9
of register 0x17 - RMII and Status Register (RCSR).
When phy_interface_is_rgmii rgmii mode must be enabled, same for
contrary, this prevents malconfigurations of hw straps
References:
- https://www.ti.com/lit/gpn/dp83822i p66
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Suggested-by: Alberto Bianchi <alberto.bianchi@amarulasolutions.com>
Tested-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add newly added stress_reuseport_listen object to .gitignore file.
Fixes: ec8cb4f617 ("net: selftests: Stress reuseport listen")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells says:
====================
rxrpc: Miscellaneous changes
Here are some miscellaneous changes for AF_RXRPC:
(1) Allow the list of local endpoints to be viewed through /proc.
(2) Switch to using refcount_t for refcounting.
(3) Fix a locking issue found by lockdep.
(4) Autogenerate tracing symbol enums from symbol->string maps to make it
easier to keep them in sync.
(5) Return an error to sendmsg() if a call it tried to set up failed.
Because it failed at this point, no notification will be generated for
recvmsg to pick up - but userspace still needs to know about the
failure.
(6) Fix the selection of abort codes generated by internal events. In
particular, rxrpc and kafs shouldn't be generating RX_USER_ABORT
unless it's because userspace did something to cancel a call.
(7) Adjust the interpretation and handling of certain ACK types to try and
detect NAT changes causing a call to seem to start mid-flow from a
different peer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If a client's address changes, say if it is NAT'd, this can disrupt an in
progress operation. For most operations, this is not much of a problem,
but StoreData can be different as some servers modify the target file as
the data comes in, so if a store request is disrupted, the file can get
corrupted on the server.
The problem is that the server doesn't recognise packets that come after
the change of address as belonging to the original client and will bounce
them, either by sending an OUT_OF_SEQUENCE ACK to the apparent new call if
the packet number falls within the initial sequence number window of a call
or by sending an EXCEEDS_WINDOW ACK if it falls outside and then aborting
it. In both cases, firstPacket will be 1 and previousPacket will be 0 in
the ACK information.
Fix this by the following means:
(1) If a client call receives an EXCEEDS_WINDOW ACK with firstPacket as 1
and previousPacket as 0, assume this indicates that the server saw the
incoming packets from a different peer and thus as a different call.
Fail the call with error -ENETRESET.
(2) Also fail the call if a similar OUT_OF_SEQUENCE ACK occurs if the
first packet has been hard-ACK'd. If it hasn't been hard-ACK'd, the
ACK packet will cause it to get retransmitted, so the call will just
be repeated.
(3) Make afs_select_fileserver() treat -ENETRESET as a straight fail of
the operation.
(4) Prioritise the error code over things like -ECONNRESET as the server
did actually respond.
(5) Make writeback treat -ENETRESET as a retryable error and make it
redirty all the pages involved in a write so that the VM will retry.
Note that there is still a circumstance that I can't easily deal with: if
the operation is fully received and processed by the server, but the reply
is lost due to address change. There's no way to know if the op happened.
We can examine the server, but a conflicting change could have been made by
a third party - and we can't tell the difference. In such a case, a
message like:
kAFS: vnode modified {100058:146266} b7->b8 YFS.StoreData64 (op=2646a)
will be logged to dmesg on the next op to touch the file and the client
will reset the inode state, including invalidating clean parts of the
pagecache.
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Link: http://lists.infradead.org/pipermail/linux-afs/2021-December/004811.html # v1
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX_USER_ABORT code should really only be used to indicate that the user
of the rxrpc service (ie. userspace) implicitly caused a call to be aborted
- for instance if the AF_RXRPC socket is closed whilst the call was in
progress. (The user may also explicitly abort a call and specify the abort
code to use).
Change some of the points of generation to use other abort codes instead:
(1) Abort the call with RXGEN_SS_UNMARSHAL or RXGEN_CC_UNMARSHAL if we see
ENOMEM and EFAULT during received data delivery and abort with
RX_CALL_DEAD in the default case.
(2) Abort with RXGEN_SS_MARSHAL if we get ENOMEM whilst trying to send a
reply.
(3) Abort with RX_CALL_DEAD if we stop hearing from the peer if we had
heard from the peer and abort with RX_CALL_TIMEOUT if we hadn't.
(4) Abort with RX_CALL_DEAD if we try to disconnect a call that's not
completed successfully or been aborted.
Reported-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
If at the end of rxrpc sendmsg() or rxrpc_kernel_send_data() the call that
was being given data was aborted remotely or otherwise failed, return an
error rather than returning the amount of data buffered for transmission.
The call (presumably) did not complete, so there's not much point
continuing with it. AF_RXRPC considers it "complete" and so will be
unwilling to do anything else with it - and won't send a notification for
it, deeming the return from sendmsg sufficient.
Not returning an error causes afs to incorrectly handle a StoreData
operation that gets interrupted by a change of address due to NAT
reconfiguration.
This doesn't normally affect most operations since their request parameters
tend to fit into a single UDP packet and afs_make_call() returns before the
server responds; StoreData is different as it involves transmission of a
lot of data.
This can be triggered on a client by doing something like:
dd if=/dev/zero of=/afs/example.com/foo bs=1M count=512
at one prompt, and then changing the network address at another prompt,
e.g.:
ifconfig enp6s0 inet 192.168.6.2 && route add 192.168.6.1 dev enp6s0
Tracing packets on an Auristor fileserver looks something like:
192.168.6.1 -> 192.168.6.3 RX 107 ACK Idle Seq: 0 Call: 4 Source Port: 7000 Destination Port: 7001
192.168.6.3 -> 192.168.6.1 AFS (RX) 1482 FS Request: Unknown(64538) (64538)
192.168.6.3 -> 192.168.6.1 AFS (RX) 1482 FS Request: Unknown(64538) (64538)
192.168.6.1 -> 192.168.6.3 RX 107 ACK Idle Seq: 0 Call: 4 Source Port: 7000 Destination Port: 7001
<ARP exchange for 192.168.6.2>
192.168.6.2 -> 192.168.6.1 AFS (RX) 1482 FS Request: Unknown(0) (0)
192.168.6.2 -> 192.168.6.1 AFS (RX) 1482 FS Request: Unknown(0) (0)
192.168.6.1 -> 192.168.6.2 RX 107 ACK Exceeds Window Seq: 0 Call: 4 Source Port: 7000 Destination Port: 7001
192.168.6.1 -> 192.168.6.2 RX 74 ABORT Seq: 0 Call: 4 Source Port: 7000 Destination Port: 7001
192.168.6.1 -> 192.168.6.2 RX 74 ABORT Seq: 29321 Call: 4 Source Port: 7000 Destination Port: 7001
The Auristor fileserver logs code -453 (RXGEN_SS_UNMARSHAL), but the abort
code received by kafs is -5 (RX_PROTOCOL_ERROR) as the rx layer sees the
condition and generates an abort first and the unmarshal error is a
consequence of that at the application layer.
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Link: http://lists.infradead.org/pipermail/linux-afs/2021-December/004810.html # v1
Signed-off-by: David S. Miller <davem@davemloft.net>
Automatically generate trace tag enums from the symbol -> string mapping
tables rather than having the enums as well, thereby reducing duplicated
data.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a locking issue with the per-netns list of calls in rxrpc. The
pieces of code that add and remove a call from the list use write_lock()
and the calls procfile uses read_lock() to access it. However, the timer
callback function may trigger a removal by trying to queue a call for
processing and finding that it's already queued - at which point it has a
spare refcount that it has to do something with. Unfortunately, if it puts
the call and this reduces the refcount to 0, the call will be removed from
the list. Unfortunately, since the _bh variants of the locking functions
aren't used, this can deadlock.
================================
WARNING: inconsistent lock state
5.18.0-rc3-build4+ #10 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
ksoftirqd/2/25 [HC0[0]:SC1[1]:HE1:SE0] takes:
ffff888107ac4038 (&rxnet->call_lock){+.?.}-{2:2}, at: rxrpc_put_call+0x103/0x14b
{SOFTIRQ-ON-W} state was registered at:
...
Possible unsafe locking scenario:
CPU0
----
lock(&rxnet->call_lock);
<Interrupt>
lock(&rxnet->call_lock);
*** DEADLOCK ***
1 lock held by ksoftirqd/2/25:
#0: ffff8881008ffdb0 ((&call->timer)){+.-.}-{0:0}, at: call_timer_fn+0x5/0x23d
Changes
=======
ver #2)
- Changed to using list_next_rcu() rather than rcu_dereference() directly.
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Move to using refcount_t rather than atomic_t for refcounts in rxrpc.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the list of in-use local UDP endpoints in the current network
namespace to be viewed in /proc.
To aid with this, the endpoint list is converted to an hlist and RCU-safe
manipulation is used so that the list can be read with only the RCU
read lock held.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder says:
====================
net: ipa: a few more small items
This series consists of three small sets of changes. Version 2 adds
a patch that avoids a warning that occurs when handling a modem
crash (I unfortunately didn't notice it earlier). All other patches
are the same--just rebased.
The first three patches allow a few endpoint features to be
specified. At this time, currently-defined endpoints retain the
same configuration, but when the monitor functionality is added in
the next cycle these options will be required.
The fourth patch simply removes an unused function, explaining also
why it would likely never be used.
The fifth patch is new. It counts the number of modem TX endpoints
and uses it to determine how many TREs a transaction needs when
when handling a modem crash. It is needed to avoid exceeding the
limited number of commands imposed by the last four patches.
And the last four patches refactor code related to IPA immediate
commands, eliminating an unused field and then simplifying and
removing some unneeded code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 64-bit data field in a transaction is not used for commands.
And the opcode array is *only* used for commands. They're
(currently) the same size; save a little space in the transaction
structure by enclosing the two fields in a union.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipa_cmd_info structure now contains only one field, and it's an
enumerated type whose values all fit in 8 bits. Currently we'll
never use more than 8 TREs in a command transaction, and we can
represent that number of command opcodes in the same space as a 64
bit pointer to an ipa_cmd_info structure.
Define IPA_COMMAND_TRANS_TRE_MAX as the maximum number of TREs that
can be in a command transaction. Replace the info pointer in a
transaction with a fixed-size array named cmd_opcode[] of that many
bytes. Store the opcode in this array when adding a command TRE to
a transaction, as was done previously for the info array. This
makes the ipa_cmd_info unused, so get rid of it.
When committing an immediate command transaction, use the channel's
Boolean command flag to determine whether to fill in the opcode,
which will be taken (as before) from the array in the transaction.
This makes the command info pool unnecessary, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer use the direction argument for gsi_trans_cmd_add(), so
get rid of it in its definition, and in its seven callers.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The direction field of the ipa_cmd_info structure is set, but never
used. It seems it might have been used for the DMA_SHARED_MEM
immediate command, but the DIRECTION flag is set based on the value
of the passed-in direction flag there.
Anyway, remove this unused field from the ipa_cmd_info structure.
This is done as a separate patch to make it very obvious that it's
not required.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_endpoint_modem_exception_reset_all(), a high estimate was
made of the number of endpoints that need their status register
updated. We only used what was needed, so the high estimate didn't
matter much.
However the next few patches are going to limit the number of
commands in a single transaction, and the overestimate would exceed
that. So count the number of modem TX endpoints at initialization
time, and use it in ipa_endpoint_modem_exception_reset_all().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the beginning gsi_trans_commit_wait_timeout() has existed to
provide a way to allow waiting a limited time for a transaction
to complete. But that function has never been used.
In fact, there is no use for this function, because a transaction
committed to hardware should *always* complete. The only reason it
might not complete is if there were a hardware failure, or perhaps a
system configuration error.
Furthermore, if a timeout ever did occur, the IPA hardware would be
in an indeterminate state, from which there is no recovery. It
would require some sort of complete IPA reset, and would require the
participation of the modem, and at this time there is no such
sequence defined.
So get rid of the definition of gsi_trans_commit_wait_timeout(), and
update a few comments accordingly.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't assume that a 500 microsecond time limit should be used for
all receive endpoints that support aggregation. Instead, specify
the time limit to use in the configuration data.
Set a 500 microsecond limit for all existing RX endpoints, as before.
Checking for overflow for the time limit field is a bit complicated.
Rather than duplicate a lot of code in ipa_endpoint_data_valid_one(),
call WARN() if any value is found to be too large when encoding it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new flag for AP receive endpoints that indicates whether
a "hard limit" is used as a criterion for closing aggregation.
Add comments explaining the difference between "hard" and "soft"
aggregation limits.
Pass a flag to ipa_aggr_size_kb() so it computes the proper
aggregation size value whether using hard or soft limits. Move
that function earlier in "ipa_endpoint.c" so it can be used
without a forward-reference.
Update ipa_endpoint_data_valid_one() so it validates endpoints whose
data indicate a hard aggregation limit is used, and so it reports
set aggregation flags for endpoints without aggregation enabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new Boolean flag for RX endpoints defining whether HOLB drop
is initially enabled or disabled for the endpoint. All existing AP
endpoints should have HOLB drop disabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling mistakes (triple letters) in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling mistakes (triple letters) in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joanne Koong says:
====================
Add a bhash2 table hashed by port + address
This patchset proposes adding a bhash2 table that hashes by port and address.
The motivation behind bhash2 is to expedite bind requests in situations where
the port has many sockets in its bhash table entry, which makes checking bind
conflicts costly especially given that we acquire the table entry spinlock
while doing so, which can cause softirq cpu lockups and can prevent new tcp
connections.
We ran into this problem at Meta where the traffic team binds a large number
of IPs to port 443 and the bind() call took a significant amount of time
which led to cpu softirq lockups, which caused packet drops and other failures
on the machine
The patches are as follows:
1/2 - Adds a second bhash table (bhash2) hashed by port and address
2/2 - Adds a test for timing how long an additional bind request takes when
the bhash entry is populated
When experimentally testing this on a local server for ~24k sockets bound to
the port, the results seen were:
ipv4:
before - 0.002317 seconds
with bhash2 - 0.000018 seconds
ipv6:
before - 0.002431 seconds
with bhash2 - 0.000021 seconds
====================
Link: https://lore.kernel.org/r/20220520001834.2247810-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This test populates the bhash table for a given port with
MAX_THREADS * MAX_CONNECTIONS sockets, and then times how long
a bind request on the port takes.
When populating the bhash table, we create the sockets and then bind
the sockets to the same address and port (SO_REUSEADDR and SO_REUSEPORT
are set). When timing how long a bind on the port takes, we bind on a
different address without SO_REUSEPORT set. We do not set SO_REUSEPORT
because we are interested in the case where the bind request does not
go through the tb->fastreuseport path, which is fragile (eg
tb->fastreuseport path does not work if binding with a different uid).
To run the test locally, I did:
* ulimit -n 65535000
* ip addr add 2001:0db8:0:f101::1 dev eth0
* ./bind_bhash_test 443
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We currently have one tcp bind table (bhash) which hashes by port
number only. In the socket bind path, we check for bind conflicts by
traversing the specified port's inet_bind2_bucket while holding the
bucket's spinlock (see inet_csk_get_port() and inet_csk_bind_conflict()).
In instances where there are tons of sockets hashed to the same port
at different addresses, checking for a bind conflict is time-intensive
and can cause softirq cpu lockups, as well as stops new tcp connections
since __inet_inherit_port() also contests for the spinlock.
This patch proposes adding a second bind table, bhash2, that hashes by
port and ip address. Searching the bhash2 table leads to significantly
faster conflict resolution and less time holding the spinlock.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GCC array-bounds warns that ipc_coredump_get_list() under-allocates
the size of struct iosm_cd_table *cd_table.
This is avoidable - we just need a flexible array. Nothing calls
sizeof() on struct iosm_cd_list or anything that contains it.
Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Link: https://lore.kernel.org/r/20220520060013.2309497-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GCC array bounds checking complains that ulp_id is validated
only against upper bound. Make it unsigned.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220520061955.2312968-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 49bb39bdda ("selftests: fib_nexthops: Make the test more robust")
increased the timeout of ping commands to 5 seconds, to make the test
more robust. Make the timeout configurable using '-w' argument to allow
user to change it depending on the system that runs the test. Some systems
suffer from slow forwarding performance, so they may need to change the
timeout.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220519070921.3559701-1-amcohen@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sometimes t7xx_cldma_gpd_set_next_ptr() is called under spin lock,
so add 'gfp_mask' parameter in t7xx_cldma_gpd_set_next_ptr() to pass
the flag.
Fixes: 39d439047f ("net: wwan: t7xx: Add control DMA interface")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/20220519032108.2996400-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When user sets skb_defer_max to 1 the kick threshold is 0
(half of 1). If we increment queue length before the check
the kick will never happen, and the skb may get stranded.
This is likely harmless but can be avoided by moving the
increment after the check. This way skb_defer_max == 1
will always kick. Still a silly config to have, but
somehow that feels more correct.
While at it drop a comment which seems to be outdated
or confusing, and wrap the defer_count write with
a WRITE_ONCE() since it's read on the fast path
that avoids taking the lock.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220518185522.2038683-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Siena only supports software TSO. This means more code can be deleted,
as pointed out by the Smatch static checker warning:
drivers/net/ethernet/sfc/siena/tx.c:184 __efx_siena_enqueue_skb()
warn: duplicate check 'segments' (previous on line 158)
Fixes: 956f2d86cb ("sfc/siena: Remove build references to missing functionality")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/kernel-janitors/YoH5tJMnwuGTrn1Z@kili/
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/165294463549.23865.4557617334650441347.stgit@palantir17.mph.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Looks like the IPv6 version of the patch under Fixes was
a copy/paste of the IPv4 but hit the wrong spot.
It is tcp_v6_rcv() which uses drop_reason as a boolean, and
needs to be protected against reason == 0 before calling free.
tcp_v6_do_rcv() has a pretty straightforward flow.
The resulting warning looks like this:
WARNING: CPU: 1 PID: 0 at net/core/skbuff.c:775
Call Trace:
tcp_v6_rcv (net/ipv6/tcp_ipv6.c:1767)
ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:438)
ip6_input_finish (include/linux/rcupdate.h:726)
ip6_input (include/linux/netfilter.h:307)
Fixes: f8319dfd1b ("net: tcp: reset 'drop_reason' to NOT_SPCIFIED in tcp_v{4,6}_rcv()")
Tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Link: https://lore.kernel.org/r/20220520021347.2270207-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder says:
====================
net: ipa: a mix of patches
This series includes a mix of things things that are generally
minor. The first four are sort of unrelated fixes, and summarizing
them here wouldn't be that helpful.
The last three together make it so only the "configuration data" we
need after initialization is saved for later use. Most such data is
used only during driver initialization. But endpoint configuration
is needed later, so the last patch saves a copy of that. Eventually
we'll want to support reconfiguring endpoints at runtime as well,
and this will facilitate that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
All elements of the default endpoint configuration are used in the
code when programming an endpoint for use. But none of the other
configuration data is ever needed once things are initialized.
So rather than saving a pointer to *all* of the configuration data,
save a copy of only the endpoint configuration portion.
This will eventually allow endpoint configuration to be modifiable
at runtime. But even before that it means we won't keep a pointer
to configuration data after when no longer needed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the just-moved data structure types to drop the "_data"
suffix, to make it more obvious they are no longer meant to be used
just as read-only initialization data. Rename the fields and
variables of these types to use "config" instead of "data" in the
name. This is another small step meant to facilitate review.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the definitions of the structures defining endpoint-specific
configuration data out of "ipa_data.h" and into "ipa_endpoint.h".
This is a trivial movement of code without any other change, to
prepare for the next few patches.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
About half of the fields set by the call in ipa_modem_netdev_setup()
are overwritten after the call. Instead, just skip the call, and
open-code the (other) assignments it makes to the net_device
structure fields.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we program an RX endpoint to have no header (header length is 0),
header-related endpoint configuration values are meaningless and are
ignored.
The only case we support that defines a header is QMAP endpoints.
In ipa_endpoint_init_hdr_ext() we set the endianness mask value
unconditionally, but it should not be done if there is no header
(meaning it is not configured for QMAP).
Set the endianness conditionally, and rearrange the logic in that
function slightly to avoid testing the qmap flag twice.
Delete an incorrect comment in ipa_endpoint_init_aggr().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
