AP mode currently sets up the dual stream capability
for all stations. This patch fixes it by checking if the
associated station supports dual stream MCS rates (8-15).
We would disregard any MCS rates above 15, since Atheros
HW supports only 0..15 rates currently, and can't receive
at rates > 15 anyway.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fills the ack_signal field in TX status with an appropriate
value from the TX descriptor.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should be checking with the 4K header and not the non-4K
header size.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We always return true, checking for 'false' return value
is bogus anyway, so fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This improves readability. Handle both 4K/non-4K EEPROM
in this patch.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print the EEPROM version/revision on init.
Choose appropriate debug masks on error conditions,
and remove useless print messages.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the PCI retry timeout code as that was just taken from ipw2100
due to historical reasons but in reality its a no-op, additionally its
simply incorrect as each PCI devices has its own custom PCI configuration
space on PCI config space >= 0x40. Not to mention we were trying to write
0 to a place that already has 0 on it.
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Ben Cahill <ben.m.cahill@intel.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Tested-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the TSF offset calculation for staggered Beacon frames
and sets ATH_BCBUF back to the earlier value 4 to enable multi-BSS
configurations of up to four BSSes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a scan is queued in STA mode while the interface is in state direct
probe, authenticate or associate the scan is delayed until the interface
enters disabled or associated state. But in case of direct probe-,
authentication- or association- timeout sta_work will not be scheduled
anymore (without external trigger) and thus the pending scan is not
executed and prevents a new scan from being triggered (-EBUSY).
Fix this by queueing the sta work again after direct probe-, authentication-
and association- timeout.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No hw/driver actually supports more than four queues right now,
and we allocate a number of things per queue which means we
waste a bit of memory. Reduce the maximum number to four to
accurately reflect what we do (and need for QoS). Even if we
had hardware supporting more queues we couldn't take advantage
of that right now anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This inline is useless and actually makes the code _longer_
rather than shorter.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan capability added to cfg80211/nl80211 introduced a
dependency on nl80211 by cfg80211. We can thus no longer have
just cfg80211 without nl80211. Specifically, cfg80211_scan_done()
calls nl80211_send_scan_aborted() or nl80211_send_scan_done().
Now we remove the option for user to select nl80211. It will always
be compiled if user selects cfg80211.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't call ieee80211_sta_find_ibss() directly, like it's done in STA
mode, so that the commit() call is more harmless respectively has
less site-effects.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When there are no free snums, UCC ethernet should gracefully fail, but
currently it oopses this way:
# ifconfig eth0 up
fill_init_enet_entries: Can not get SNUM.
ucc_geth_startup: Can not fill p_init_enet_param_shadow.
eth0: Cannot configure net device, aborting.
Unable to handle kernel paging request for data at address 0x00000190
Faulting instruction address: 0xc0294c88
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c0294c88] mutex_lock+0x0/0x1c
LR [c01b6be8] phy_stop+0x20/0x70
Call Trace:
[efb25da0] [efb2eb60] 0xefb2eb60 (unreliable)
[efb25db0] [c01b2058] ucc_geth_stop+0x2c/0x8c
[efb25dd0] [c01b4194] ucc_geth_open+0x48/0x27c
[efb25df0] [c020eec0] dev_open+0xc0/0x118
[...]
This is because the ucc_geth_stop() routine assumes that ugeth->phydev
is always initialized by the ucc_geth_open(), while it is not in case
of errors.
If we add a check to the ucc_geth_stop(), then another oops pops up:
Unable to handle kernel paging request for data at address 0x00000004
Faulting instruction address: 0xc01b46a4
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01b46a4] adjust_link+0x20/0x1b4
LR [c01b770c] phy_state_machine+0xdc/0x44c
Call Trace:
[ef83bf10] [c021b388] linkwatch_schedule_work+0x74/0xf8 (unreliable)
[ef83bf40] [c01b770c] phy_state_machine+0xdc/0x44c
[ef83bf60] [c004c13c] run_workqueue+0xb8/0x148
[ef83bf90] [c004c870] worker_thread+0x70/0xd0
[ef83bfd0] [c00505fc] kthread+0x48/0x84
[ef83bff0] [c000f464] kernel_thread+0x4c/0x68
[...]
That one happens because ucc_geth_stop() does not call phy_disconnect()
and so phylib state machine is running without any idea that a MAC has
just died.
Also, when device tree specifies fixed-link, and CONFIG_FIXED_PHY
is disabled, we'll get this oops:
0:01 not found
eth2: Could not attach to PHY
eth2: Cannot initialize PHY, aborting.
Unable to handle kernel paging request for data at address 0x00000190
Faulting instruction address: 0xc02967d0
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c02967d0] mutex_lock+0x0/0x1c
LR [c01b6bcc] phy_stop+0x20/0x70
Call Trace:
[ef82be50] [efb6bb60] 0xefb6bb60 (unreliable)
[ef82be60] [c01b2058] ucc_geth_stop+0x2c/0x8c
[ef82be80] [c01b4194] ucc_geth_open+0x48/0x27c
[ef82bea0] [c0210a04] dev_open+0xc0/0x118
[ef82bec0] [c020f85c] dev_change_flags+0x84/0x1ac
[ef82bee0] [c037b768] ic_open_devs+0x168/0x2bc
[ef82bf20] [c037ca98] ip_auto_config+0x90/0x28c
[ef82bf60] [c0001b9c] do_one_initcall+0x34/0x1a0
[ef82bfd0] [c035e240] do_initcalls+0x38/0x58
[ef82bfe0] [c035e2c4] kernel_init+0x30/0x90
[ef82bff0] [c000f464] kernel_thread+0x4c/0x68
[...]
And again, ucc_geth_stop() assumes that ugeth->phydev is there, while
it isn't.
This patch fixes all three oopses simply by rearranging some code:
- In ucc_geth_open(): move init_phy() call to the beginning, so
that we only call ucc_geth_stop() with a PHY attached;
- Move phy_disconnect() call from ucc_geth_close() to
ucc_geth_stop(), so that we'll always disconnect the PHY.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inline function skb_gro_mac_header defined in include/linux/netdevice.h
makes use of page_address(). Depending on configuration options, the latter
is either defined as a macro or is declared as a function in another header
file, namely include/linux/mm.h. However, include/linux/netdevice.h does not
include include/linux/mm.h.
On MIPS, this has produced the following build error:
CC kernel/sysctl_check.o
In file included from include/linux/icmpv6.h:173,
from include/linux/ipv6.h:208,
from include/net/ip_vs.h:26,
from kernel/sysctl_check.c:6:
include/linux/netdevice.h: In function 'skb_gro_mac_header':
include/linux/netdevice.h:1132: error: implicit declaration of function
'page_address'
include/linux/netdevice.h:1133: warning: pointer/integer type mismatch
in conditional expression
make[1]: *** [kernel/sysctl_check.o] Error 1
make: *** [kernel] Error 2
The patch adds the missing include and fixes the build error.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA mapping can be expensive in the presence of iommus.
Reduce the Rx iommu activity by mapping an entire page, and provide the H/W
the mapped address + offset of the current page chunk.
Reserve bits at the end of the page to track mapping references, so the page
can be unmapped.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size_t to declare mmio start and len variables.
Print PEX error register after EEH resumed.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable timestamps, update delayed ack threshold for iSCSI/iWARP traffic
Remove the len flag in Tx requests. It might corrupt offload trace packets.
Update SGE context setup to avoid potential H/W misprogrammation.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Start queue set reclaim timers after the queue sets have been
allocated successfully.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded memset (alloc_etherdev does it already).
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_device_ops conversion left the wrong poll_controller hook.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert madge and proteon drivers which are really just subclasses
of tms380.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>