SPARSE_IRQ doesn't need to be a visible option, only those platforms
supporting that will select it.
Signed-off-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DMA coherent remap area is used to provide an uncached mapping
of memory for coherency with DMA engines. Currently, we look for
any free hole which our allocation will fit in with page alignment.
However, this can lead to fragmentation of the area, and allows small
allocations to cross L1 entry boundaries. This is undesirable as we
want to move towards allocating sections of memory.
Align allocations according to the size, limiting the alignment between
the page and section sizes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need our own implementation of this, use the generic
library implementation instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implementation of the ST-Ericsson baudrate extension in the PL011
block. In this modified variant it is possible to change the
sampling factor from 16 to 8, and thanks to this we can get higher
baudrates while still using the same peripheral clock.
Also replace the simple division to determine the baud divisor
with DIV_ROUND_CLOSEST() rather than a simple integer division.
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Jerzy Kasenberg <jerzy.kasenberg@tieto.com>
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the ST-Ericsson version of the PL011 the TX and RX have different
control registers.
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM has support for the atomic64_dec_if_positive operation
so ensure that it is tested by the atomic64_test routine.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This changes the TCM handling so that a fixed area is reserved at
0xfffe0000-0xfffeffff for TCM. This areas is used by XScale but
XScale does not have TCM so the mechanisms are mutually exclusive.
This change is needed to make TCM detection more dynamic while
still being able to compile code into it, and is a must for the
unified ARM goals: the current TCM allocation at different places
in memory for each machine would be a nightmare if you want to
compile a single image for more than one machine with TCM so it
has to be nailed down in one place.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If TCM is in use, we should display it in the virtual memory
layout along with everything else.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CPUs v6 and up support multiple TCM banks, for example an ITCM of
8k is supplied in two 4k banks. This makes the TCM work on the
1176JZF-S devchip.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The earlier TCM memory regions were mapped as MT_MEMORY_UNCACHED
which doesn't really work on platforms supporting the new v6
features like the NX bit. Add unique MT_MEMORY_[I|D]TCM types
instead.
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/fsl-booke: Fix address issue when using relocatable kernels
powerpc/cpm1: Mark micropatch code/data static and __init
powerpc/cpm1: Fix build with various CONFIG_*_UCODE_PATCH combinations
powerpc/cpm: Reintroduce global spi_pram struct (fixes build issue)
From: Bin Yang <bin.yang@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Bin Yang <bin.yang@marvell.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
via following scripts
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/lmb/memblock/g' \
-e 's/LMB/MEMBLOCK/g' \
$FILES
for N in $(find . -name lmb.[ch]); do
M=$(echo $N | sed 's/lmb/memblock/g')
mv $N $M
done
and remove some wrong change like lmbench and dlmb etc.
also move memblock.c from lib/ to mm/
Suggested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
input: i8042 - add runtime check in x86's i8042_platform_init
Revert "Input: fixup X86_MRST selects"
Revert "Input: do not force selecting i8042 on Moorestown"
x86, mrst: Add i8042_detect API for Moorestwon platform
x86: Add i8042 pre-detection hook to x86_platform_ops
x86, platform: Export x86_platform to modules
* 'arm/defconfig/reduced-v2.6.35-rc1' of git://git.pengutronix.de/git/ukl/linux-2.6:
ARM: reduce defconfigs
This is a big change, but results in no loss of information, despite us
losing almost 200k lines:
177 files changed, 652 insertions(+), 194157 deletions(-)
and Grant Likely thinks powerpc can also use the same reduction
technique.
The python script that did the reduction looks like this:
#! /usr/bin/env python
# vim: set fileencoding=utf-8 :
# Copyright (C) 2010 by Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
import re
import subprocess
import os
import sys
# This prevents including a timestamp in the .config which makes comparing a
# bit easier.
os.environ['KCONFIG_NOTIMESTAMP'] = 'Yes, please'
# XXX: get these using getopt
kernel_tree = '' # os.path.join(os.environ['HOME'], 'gsrc', 'linux-2.6')
arch = 'arm'
target = sys.argv[1]
defconfig_src = os.path.join(kernel_tree, 'arch/%s/configs/%s' % (arch, target))
subprocess.check_call(['make', '-s', 'ARCH=%s' % arch, target])
origconfig = list(open('.config'))
config = list(origconfig)
config_size = os.stat('.config').st_size
i = 0
while i < len(config):
print 'test for %r' % config[i]
defconfig = open(defconfig_src, 'w')
defconfig.writelines(config[:i])
defconfig.writelines(config[i + 1:])
defconfig.close()
subprocess.check_call(['make', '-s', 'ARCH=%s' % arch, target])
if os.stat('.config').st_size == config_size and list(open('.config')) == origconfig:
del config[i]
else:
i += 1
defconfig = open(defconfig_src, 'w')
defconfig.writelines(config)
defconfig.close()
which is pretty self-explanatory.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'v4l_for_2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB: uvc: Fix multiple symbols definitions with UVC gadget and host drivers
V4L/DVB: v4l: mem2mem_testdev: fix g_fmt NULL pointer dereference
V4L/DVB: uvcvideo: Power line frequency control doesn't support GET_MIN/MAX/RES
V4L/DVB: ivtv: Add delay to ensure the decoder always restarts with a blank screen
V4L/DVB: Documentation: Add the Philips FQ1236 MK5 to video4linux/CARDLIST.tuner
V4L/DVB: tveeprom: Add an entry for tuner code 168: a TCL M30WTP-4N-E tuner
V4L/DVB: tuner: Add a definition for the Philips FQ1236 MK5 NTSC tuner
V4L/DVB: OMAP_VOUT: fix: Module params were not working through bootargs
V4L/DVB: OMAP_VOUT: fix: Replaced dma-sg with dma-contig
V4L/DVB: OMAP_VOUT:Build FIX: Rebased against latest DSS2 changes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Send Report ID when numbered reports are sent over the control endpoint.
HID: Enable HID_QUIRK_MULTI_INPUT for Retro Adaptor
HID: add support for CH Eclipse yoke
HID: eliminate a double lock in debug code
HID: ntrig: add support for new firwmare versions
HID: check for HID_QUIRK_IGNORE during probing
HID: roccat: fix modules interdependencies
File patterns are one per line.
Fixed include file location.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After remove a rmap, we should flush all vcpu's tlb
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The Report ID wasn't sent as part of the payload for reports which were sent
over the control endpoint. This is required by section 8.1 of the HID spec.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The UVC gadget driver borrowed code from the UVC host driver without
changing the symbol names. This results in a namespace clash with
multiple definitions of several symbols when compiling both drivers in
the kernel.
Make all generic UVC functions and variables static in the UVC gadget
driver, as the symbols are not referenced outside of the gadget driver.
Rename the uvc_trace_param global variable to uvc_gadget_trace_param.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: Fix autoloading of fschmd on recent Fujitsu machines
hwmon: (coretemp) Properly label the sensors
hwmon: (coretemp) Skip duplicate CPU entries
hwmon: (it87) Fix in7 on IT8720F
hwmon: (k8temp) Fix temperature reporting for ASB1 processor revisions
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c/mips: Fix error return codes from Sibyte i2c bus driver
i2c: Fix probability check
Patch for linux-2.6.35-rc4 mainline kernel to enable Paul Qureshi's
Retro Adapter [http://keio.dk/retroadapter.html], an open source USB
device which allows controllers and joysticks from classic computers
and consoles to work on modern PCs, to appear as two separate devices
under Linux.
Signed-off-by: Peter Edwards <samwise@bagshot-row.org>
Acked-by: Paul Qureshi <retro@world3.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This USB flight yoke needs the NOGET quirk, like most of CH's other
products. This patch adds that.
Signed-off-by: Jonathan Rockway <jon@jrock.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When booting a relocatable kernel it needs to jump to the correct
start address, which for BookE parts is usually unchanged
regardless of the physical memory offset.
Recent changes cause problems with how we calculate the start
address, it was always adding the RMO into the start address
which is incorrect. This patch only adds in the RMO offset
if we are in the kexec code path, as it needs the RMO to work
correctly.
Instead of adding the RMO offset in in the common code path, we
can just set r6 to the RMO offset in the kexec code path instead
of to zero, and finally perform the masking in the common code
path
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This saves runtime memory and fixes lots of sparse warnings like this:
CHECK arch/powerpc/sysdev/micropatch.c
arch/powerpc/sysdev/micropatch.c:27:6: warning: symbol 'patch_2000'
was not declared. Should it be static?
arch/powerpc/sysdev/micropatch.c:146:6: warning: symbol 'patch_2f00'
was not declared. Should it be static?
...
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Warnings are treated as errors for arch/powerpc code, so build fails
with CONFIG_I2C_SPI_UCODE_PATCH=y:
CC arch/powerpc/sysdev/micropatch.o
cc1: warnings being treated as errors
arch/powerpc/sysdev/micropatch.c: In function 'cpm_load_patch':
arch/powerpc/sysdev/micropatch.c:630: warning: unused variable 'smp'
make[1]: *** [arch/powerpc/sysdev/micropatch.o] Error 1
And with CONFIG_USB_SOF_UCODE_PATCH=y:
CC arch/powerpc/sysdev/micropatch.o
cc1: warnings being treated as errors
arch/powerpc/sysdev/micropatch.c: In function 'cpm_load_patch':
arch/powerpc/sysdev/micropatch.c:629: warning: unused variable 'spp'
arch/powerpc/sysdev/micropatch.c:628: warning: unused variable 'iip'
make[1]: *** [arch/powerpc/sysdev/micropatch.o] Error 1
This patch fixes these issues by introducing proper #ifdefs.
Cc: <stable@kernel.org> [ .33, .34 ]
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
spi_t was removed in commit 644b2a680c
("powerpc/cpm: Remove SPI defines and spi structs"), the commit assumed
that spi_t isn't used anywhere outside of the spi_mpc8xxx driver. But
it appears that the struct is needed for micropatch code. So, let's
reintroduce the struct.
Fixes the following build issue:
CC arch/powerpc/sysdev/micropatch.o
micropatch.c: In function 'cpm_load_patch':
micropatch.c:629: error: expected '=', ',', ';', 'asm' or '__attribute__' before '*' token
micropatch.c:629: error: 'spp' undeclared (first use in this function)
micropatch.c:629: error: (Each undeclared identifier is reported only once
micropatch.c:629: error: for each function it appears in.)
Reported-by: LEROY Christophe <christophe.leroy@c-s.fr>
Reported-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: <stable@kernel.org> [ .33, .34 ]
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CPU: Testing write buffer coherency: ok
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:3145 check_flags+0xcc/0x1dc()
Modules linked in:
[<c0035120>] (unwind_backtrace+0x0/0xf8) from [<c0355374>] (dump_stack+0x20/0x24)
[<c0355374>] (dump_stack+0x20/0x24) from [<c0060c04>] (warn_slowpath_common+0x58/0x70)
[<c0060c04>] (warn_slowpath_common+0x58/0x70) from [<c0060c3c>] (warn_slowpath_null+0x20/0x24)
[<c0060c3c>] (warn_slowpath_null+0x20/0x24) from [<c008f224>] (check_flags+0xcc/0x1dc)
[<c008f224>] (check_flags+0xcc/0x1dc) from [<c00945dc>] (lock_acquire+0x50/0x140)
[<c00945dc>] (lock_acquire+0x50/0x140) from [<c0358434>] (_raw_spin_lock+0x50/0x88)
[<c0358434>] (_raw_spin_lock+0x50/0x88) from [<c00fd114>] (set_task_comm+0x2c/0x60)
[<c00fd114>] (set_task_comm+0x2c/0x60) from [<c007e184>] (kthreadd+0x30/0x108)
[<c007e184>] (kthreadd+0x30/0x108) from [<c0030104>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1b75b31a2719ed1c ]---
possible reason: unannotated irqs-on.
irq event stamp: 3
hardirqs last enabled at (2): [<c0059bb0>] finish_task_switch+0x48/0xb0
hardirqs last disabled at (3): [<c002f0b0>] ret_slow_syscall+0xc/0x1c
softirqs last enabled at (0): [<c005f3e0>] copy_process+0x394/0xe5c
softirqs last disabled at (0): [<(null)>] (null)
Fix this by ensuring that the lockdep interrupt state is manipulated in
the appropriate places. We essentially treat userspace as an entirely
separate environment which isn't relevant to lockdep (lockdep doesn't
monitor userspace.) We don't tell lockdep that IRQs will be enabled
in that environment.
Instead, when creating kernel threads (which is a rare event compared
to entering/leaving userspace) we have to update the lockdep state. Do
this by starting threads with IRQs disabled, and in the kthread helper,
tell lockdep that IRQs are enabled, and enable them.
This provides lockdep with a consistent view of the current IRQ state
in kernel space.
This also revert portions of 0d928b0b61
which didn't fix the problem.
Tested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sibyte i2c bus driver returns non-descriptive error values.
Update to return error values as defined in Documentation/i2c/fault-codes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new unified probing function differs from the original code, and
the preliminary test whether probing is possible must be updated
accordingly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fujitsu slightly changed the DMI strings in their recent machines,
(for example the D2778) and this breaks the automatic loading of the
needed fschmd driver. Being more tolerant on string comparison fixes
the issue.
This closes bug #15634:
https://bugzilla.kernel.org/show_bug.cgi?id=15634
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sergey Spiridonov <sena@hurd.homeunix.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Don't assume that CPU entry number and core ID always match. It
worked in the simple cases (single CPU, no HT) but fails on
multi-CPU systems.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Cc: stable@kernel.org
On hyper-threaded CPUs, each core appears twice in the CPU list. Skip
the second entry to avoid duplicate sensors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Cc: stable@kernel.org
The IT8720F has no VIN7 pin, so VCCH should always be routed
internally to VIN7 with an internal divider. Curiously, there still
is a configuration bit to control this, which means it can be set
incorrectly. And even more curiously, many boards out there are
improperly configured, even though the IT8720F datasheet claims that
the internal routing of VCCH to VIN7 is the default setting. So we
force the internal routing in this case.
It turns out that all boards with the wrong setting are from Gigabyte,
so I suspect a BIOS bug. But it's easy enough to workaround in the
driver, so let's do it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Cc: stable@kernel.org
Reported temperature for ASB1 CPUs is too high.
Add ASB1 CPU revisions (these are also non-desktop variants) to the
list of CPUs for which the temperature fixup is not required.
Example: (from LENOVO ThinkPad Edge 13, 01972NG, system was idle)
Current kernel reports
$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +74.0 C
Core0 Temp: +70.0 C
Core1 Temp: +69.0 C
Core1 Temp: +70.0 C
With this patch I have
$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +54.0 C
Core0 Temp: +51.0 C
Core1 Temp: +48.0 C
Core1 Temp: +49.0 C
Cc: stable@kernel.org [.32.x .33.x, .34.x]
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The MTU wallclock timing fix-up patch was hardwired to the DB8500
causing a regression. This makes it work on the DB5500 as well.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The TLS register is only available on ARM1136 r1p0 and later.
Set HWCAP_TLS flags if hardware TLS is available and test for
it if CONFIG_CPU_32v6K is not set for V6.
Note that we set the TLS instruction in __kuser_get_tls
dynamically as suggested by Jamie Lokier <jamie@shareable.org>.
Also the __switch_to code is optimized out in most cases as
suggested by Nicolas Pitre <nico@fluxnic.net>.
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow SH-Mobile ARM users to adjust FORCE_MAX_ZONEORDER.
The Kconfig entry is taken from SH and non-4K page size
stuff has been trimmed away. For now only SH-Mobile ARM is
allowed to change this variable, SA1111 configs are kept at
"9" and the rest at "11".
CONFIG_FORCE_MAX_ZONEORDER lets the user tweak the maximum
amount of physically contiguous memory that can be allocated
by the kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MVFR0 and MVFR1 are only available starting with ARM1136 r1p0 release
according to "B.5 VFP changes" in DDI0211F_arm1136_r1p0_trm.pdf. This is
also when TLS register got added, so we can use HAS_TLS also to test for
MVFR0 and MVFR1.
Otherwise VFPFMRX and VFPFMXR access fails and we get:
Internal error: Oops - undefined instruction: 0 [#1]
PC is at no_old_VFP_process+0x8/0x3c
LR is at __und_svc+0x48/0x80
...
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch enables the HAVE_REGS_AND_STACK_ACCESS_API option
for ARM which is required by the kprobe events tracer. Code based
on the PowerPC port.
Cc: Jean Pihet <jpihet@mvista.com>
Tested-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds mappings from DWARF register numbers to the register
names used by the ARM `Regs and Stack Access API'.
Cc: Jean Pihet <jpihet@mvista.com>
Tested-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
