Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800_init_rfcsr() is too big, split RF initialization into per chip
functions. Code will change, but we should setup the same values onto
RF registers and in the same order as before.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows to let sparse check that the NIC access is
always released.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix typo in the macro name and the wrong value.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Synchronizing the IRQ is pointless when we will
then enable the RF-Kill interrupt again, but is
needed before we free it and the data needed to
handle IRQs; move it to the free function.
Simiarly, cancelling the replenish work struct
can move to the function that frees the RX data
structures.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to request the IRQ every time the
device is started, we can request it just once.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_trans_grab_nic_access returns a boolean. So ret should
explicitely set to an error code and not rely on the value
returned by iwl_trans_grab_nic_access.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Different transports implement the access to the SRAM in
different ways. Virtualize it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since different transports have different ways to wake the
up the NIC, we need to virtualize it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use __packed instead of __attribute__((packed)).
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, the fw should run even if the NIC is in
RFKILL. Make the API more flexible to allow that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No need to verify that the fw has been written correctly.
In case it hasn't, we won't get ALIVE notification.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we take a pointer to the tid_data, then use it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When TX aggregation is stopped, there are a few
different cases:
- connection with the peer was dropped
- session stop was requested locally
- session stop was requested by the peer
- connection was dropped while a session is stopping
The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.
Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.
In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of returning an error and filling a pointer
return the pointer and an ERR_PTR value in error cases.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel bandwidth handling isn't really quite right,
it assumes that a 40 MHz channel is really two 20 MHz
channels, which isn't strictly true. This is the way the
regulatory database handling is defined right now though
so remove the logic to handle other channel widths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Paged RX, i.e. SKBs with (some of) the data in pages instead
of the SKB header data (skb->data) can behave differently in
the stack and cause other bugs. To make debugging easier add
an option to hwsim to test with such SKBs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- cxgb4 changes to fix lookup engine hash collisions
- mlx4 changes to make flow steering usable
- fix to IPoIB to avoid pinning dst reference for too long
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lDXt
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull more infiniband changes from Roland Dreier:
"Second batch of InfiniBand/RDMA changes for 3.8:
- cxgb4 changes to fix lookup engine hash collisions
- mlx4 changes to make flow steering usable
- fix to IPoIB to avoid pinning dst reference for too long"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cxgb4: Fix bug for active and passive LE hash collision path
RDMA/cxgb4: Fix LE hash collision bug for passive open connection
RDMA/cxgb4: Fix LE hash collision bug for active open connection
mlx4_core: Allow choosing flow steering mode
mlx4_core: Adjustments to Flow Steering activation logic for SR-IOV
mlx4_core: Fix error flow in the flow steering wrapper
mlx4_core: Add QPN enforcement for flow steering rules set by VFs
cxgb4: Add LE hash collision bug fix path in LLD driver
cxgb4: Add T4 filter support
IPoIB: Call skb_dst_drop() once skb is enqueued for sending
Latinoware 2012.
There's a slightly non-trivial merge in virtio-net, as we cleaned up the
virtio add_buf interface while DaveM accepted the mq virtio-net patches.
You can see my solution in my pending-rebases branch, if that helps, but I
know you love merging:
https://git.kernel.org/?p=linux/kernel/git/rusty/linux.git;a=commit;h=12e4e64fa66a4c812e4855de32abdb4d819526fe
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=myDR
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio update from Rusty Russell:
"Some nice cleanups, and even a patch my wife did as a "live" demo for
Latinoware 2012.
There's a slightly non-trivial merge in virtio-net, as we cleaned up
the virtio add_buf interface while DaveM accepted the mq virtio-net
patches."
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (27 commits)
virtio_console: Add support for remoteproc serial
virtio_console: Merge struct buffer_token into struct port_buffer
virtio: add drv_to_virtio to make code clearly
virtio: use dev_to_virtio wrapper in virtio
virtio-mmio: Fix irq parsing in command line parameter
virtio_console: Free buffers from out-queue upon close
virtio: Convert dev_printk(KERN_<LEVEL> to dev_<level>(
virtio_console: Use kmalloc instead of kzalloc
virtio_console: Free buffer if splice fails
virtio: tools: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: scsi: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: rpmsg: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: net: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: console: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: make virtqueue_add_buf() returning 0 on success, not capacity.
virtio: console: don't rely on virtqueue_add_buf() returning capacity.
virtio_net: don't rely on virtqueue_add_buf() returning capacity.
virtio-net: remove unused skb_vnet_hdr->num_sg field
virtio-net: correct capacity math on ring full
virtio: move queue_index and num_free fields into core struct virtqueue.
...
Retries active opens for INUSE errors.
Logs any active ofld_connect_wr error replies.
Sends ofld_connect_wr on same ctrlq. It needs to go on the same control txq as
regular CPL active/passive messages.
Retries on active open replies with EADDRINUSE.
Uses active open fw wr only if active filter region is set.
Adds stat for ofld_connect_wr failures.
This patch also adds debugfs file to show endpoints.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
It establishes passive open connection through firmware work request. Passive
open connection will go through this path as now instead of listening server we
create a server filter which will redirect the incoming SYN packet to the
offload queue. After this driver tries to establish the connection using
firmware work request.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
It enables establishing active open connection using fw_ofld_connection work
request when cpl_act_open_rpl says TCAM full error which may be because
of LE hash collision. Current support is only for IPv4 active open connections.
Sets ntuple bits in active open requests. For T4 firmware greater than 1.4.10.0
ntuple bits are required to be set.
Adds nocong and enable_ecn module parameter options.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
[ Move all FW return values to t4fw_api.h. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull networking fixes from David Miller:
1) Really fix tuntap SKB use after free bug, from Eric Dumazet.
2) Adjust SKB data pointer to point past the transport header before
calling icmpv6_notify() so that the headers are in the state which
that function expects. From Duan Jiong.
3) Fix ambiguities in the new tuntap multi-queue APIs. From Jason
Wang.
4) mISDN needs to use del_timer_sync(), from Konstantin Khlebnikov.
5) Don't destroy mutex after freeing up device private in mac802154,
fix also from Konstantin Khlebnikov.
6) Fix INET request socket leak in TCP and DCCP, from Christoph Paasch.
7) SCTP HMAC kconfig rework, from Neil Horman.
8) Fix SCTP jprobes function signature, otherwise things explode, from
Daniel Borkmann.
9) Fix typo in ipv6-offload Makefile variable reference, from Simon
Arlott.
10) Don't fail USBNET open just because remote wakeup isn't supported,
from Oliver Neukum.
11) be2net driver bug fixes from Sathya Perla.
12) SOLOS PCI ATM driver bug fixes from Nathan Williams and David
Woodhouse.
13) Fix MTU changing regression in 8139cp driver, from John Greene.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
solos-pci: ensure all TX packets are aligned to 4 bytes
solos-pci: add firmware upgrade support for new models
solos-pci: remove superfluous debug output
solos-pci: add GPIO support for newer versions on Geos board
8139cp: Prevent dev_close/cp_interrupt race on MTU change
net: qmi_wwan: add ZTE MF880
drivers/net: Use of_match_ptr() macro in smsc911x.c
drivers/net: Use of_match_ptr() macro in smc91x.c
ipv6: addrconf.c: remove unnecessary "if"
bridge: Correctly encode addresses when dumping mdb entries
bridge: Do not unregister all PF_BRIDGE rtnl operations
use generic usbnet_manage_power()
usbnet: generic manage_power()
usbnet: handle PM failure gracefully
ksz884x: fix receive polling race condition
qlcnic: update driver version
qlcnic: fix unused variable warnings
net: fec: forbid FEC_PTP on SoCs that do not support
be2net: fix wrong frag_idx reported by RX CQ
be2net: fix be_close() to ensure all events are ack'ed
...
commit: cb64edb6b8 upstream
Above commit may introduce a race between cp_interrupt and dev_close
/ change MTU / dev_open up state. Changes cp_interrupt to tolerate
this. Change spin_locking in cp_interrupt to avoid possible
but unobserved race.
Reported-by: "Francois Romieu" <romieu@fr.zoreil.com>
Tested on virtual hardware, Tx MTU size up to 4096, max tx payload
was ping -s 4068 for MTU of 4096. No real hardware, need test
assist.
Signed-off-by: "John Greene" <jogreene@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: "David Woodhouse" <David.Woodhouse@intel.com>
Tested-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver description files gives these names to the vendor specific
functions on this modem:
diag: VID_19D2&PID_0284&MI_00
nmea: VID_19D2&PID_0284&MI_01
at: VID_19D2&PID_0284&MI_02
mdm: VID_19D2&PID_0284&MI_03
net: VID_19D2&PID_0284&MI_04
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CONFIG_OF guard and use of_match_ptr macro.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This covers the drivers that can use a primitive
implementation.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Centralise common code for manage_power() in usbnet
by making a generic simple implementation
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a device fails to do remote wakeup, this is no reason
to abort an open totally. This patch just continues without
runtime PM.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz884x driver does receive processing in a custom tasklet, and
seems to be assuming that since it takes its private interface spinlock
with spin_lock_irq(), it won't be running concurrently with its own
interrupt handler, as it cannot be preempted by it, but since its
interrupt handler doesn't do any locking whatsoever, the receive
processing tasklet and interrupt handler can end up running concurrently
on different CPUs.
As a result of this, the ksz884x receive path ends up locking up fairly
easily, when the receive processing tasklet's reenabling of receive
interrupts (due to it being done with polling the receive ring) races
with the interrupt handler's disabling of receive interrupts (due to a
new receive interrupt coming in) resulting in the receive interrupt
being masked but the receive processing tasklet not being scheduled.
Fix this by making the ksz884x interrupt handler take its private
interface spinlock. This requires upgrading the spin_lock() in the
transmit cleanup tasklet to a spin_lock_irq(), as otherwise the IRQ
handler can preempt transmit cleanup and deadlock the system, but
with those two changes, no more receive lockups have been observed.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
----
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic_hw.c:370: warning: variable cmd_desc set but not used
qlcnic_hw.c:368: warning: variable consumer set but not used
qlcnic_main.c:448: warning: variable ref_count set but not used
qlcnic_main.c:534: warning: variable mem_base set but not used
qlcnic_ctx.c:137: warning: variable tmp_tmpl set but not used
qlcnic_ctx.c:133: warning: variable version set but not used
qlcnic_minidump.c:200: warning: variable opcode set but not used
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device managed flow steering will be enabled only under administrator
directive provided through setting the existing module parameter
log_num_mgm_entry_size to -1 (if the device actually supports flow
steering). If flow steering isn't requested or not available, the
driver will use the value of log_num_mgm_entry_size and B0 steering.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Separate flow steering capability detection from the decision to activate.
For the master (and for native), detect the flow steering capability
in mlx4_dev_cap, but activate the appropriate steering type in a new
function choose_flow_steering() based on detected data.
For VFs, activate flow steering based on what was actually activated
by the master, where that info is obtained via QUERY_HCA. This fixes
the current VF detection which is wrongly based on QUERY_DEV_CAP.
Also, for SR-IOV mode, if flow steering may be activated, do so only
if the max number of QPs per rule is sufficient to satisfy one
subscription per VF. If not, fall back to B0 mode. This is needed to
serve registrations done by L2 network drivers such as mlx4_en and
IPoIB when the network stack attempts to join to multicast groups such
as all-hosts or the IPoIB broadcast group.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The error flow of the flow steering wrapper had a typo which caused
the wrong firmware command to be called, fix it.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Since VFs may be mapped to VMs which aren't trusted entities, flow
steering rules attached through the wrapper on behalf of VFs must be
checked to make sure that the specified QP number is assigned to that
VF. Also, make sure to keep the QP busy till the end of the operation
from the resource tracker point of view.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
It supports establishing passive open connection through firmware filter work
request. Passive open connection will go through this path as now instead of
listening server we create a server filter which will redirect the incoming SYN
packet to the offload queue.
It divides filter region into regular filters and server filter portion. It
introduces new server filter region which will be exclusively used for creating
server filters. This region will not overlap with regular filter region.
It provides new API cxgb4_alloc_sftid in LLD for getting stid in case of LE
hash collision path. This new stid will be used to open server filter in the
filter region.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The T4 architecture is capable of filtering ingress packets at line rate
using the rule in TCAM. If packet hits a rule in the TCAM then it can be either
dropped or passed to the receive queues based on a rule settings.
This patch adds framework for managing filters and to use T4's filter
capabilities. It constructs a Firmware Filter Work Request which writes the
filter at a specified index to get the work done. It hosts shadow copy of
ingress filter entry to check field size limitations and save memory in the
case where the filter table is large.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Beside imx6q, the kernel built from imx_v6_v7_defconfig is also
supposed to be running on other IMX SoCs that do not have the PTP
block. Before fec driver gets fixed to run-time detect target hardware
rather than conditional compiling with #ifdef CONFIG_FEC_PTP, let's
give it a quick fix in Kconfig to forbid FEC_PTP on those IMX SoCs that
do not support PTP.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX CQ can report completions with invalid frag_idx when the RXQ that
was *previously* using it, was not cleaned up properly. This hits
a BUG_ON() in be2net.
When completion coalescing is enabled on a CQ, an explicit CQ-notify
(with rearm) is needed for each compl, to flush partially coalesced CQ
entries that are pending DMA.
In be_close(), this fix now notifies CQ for each compl, waits explicitly
for the flush compl to arrive and complains if it doesn't arrive.
Also renaming be_crit_error() to be_hw_error() as it's the more
appropriate name and to convey that we don't wait for the flush compl
only when a HW error has occurred.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In be_close(), be_eq_clean() must be called after all RX/TX/MCC queues
have been cleaned to ensure that any events caused while cleaning up
completions are notified/acked. Not clearing all events can cause
upredictable behaviour when RX rings are re-created in the subsequent
be_open().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc update from Benjamin Herrenschmidt:
"The main highlight is probably some base POWER8 support. There's more
to come such as transactional memory support but that will wait for
the next one.
Overall it's pretty quiet, or rather I've been pretty poor at picking
things up from patchwork and reviewing them this time around and Kumar
no better on the FSL side it seems..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (73 commits)
powerpc+of: Rename and fix OF reconfig notifier error inject module
powerpc: mpc5200: Add a3m071 board support
powerpc/512x: don't compile any platform DIU code if the DIU is not enabled
powerpc/mpc52xx: use module_platform_driver macro
powerpc+of: Export of_reconfig_notifier_[register,unregister]
powerpc/dma/raidengine: add raidengine device
powerpc/iommu/fsl: Add PAMU bypass enable register to ccsr_guts struct
powerpc/mpc85xx: Change spin table to cached memory
powerpc/fsl-pci: Add PCI controller ATMU PM support
powerpc/86xx: fsl_pcibios_fixup_bus requires CONFIG_PCI
drivers/virt: the Freescale hypervisor driver doesn't need to check MSR[GS]
powerpc/85xx: p1022ds: Use NULL instead of 0 for pointers
powerpc: Disable relocation on exceptions when kexecing
powerpc: Enable relocation on during exceptions at boot
powerpc: Move get_longbusy_msecs into hvcall.h and remove duplicate function
powerpc: Add wrappers to enable/disable relocation on exceptions
powerpc: Add set_mode hcall
powerpc: Setup relocation on exceptions for bare metal systems
powerpc: Move initial mfspr LPCR out of __init_LPCR
powerpc: Add relocation on exception vector handlers
...
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable@vger.kernel.org
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
