Static checker warning complains on uninitialized variable:
drivers/net/ethernet/netronome/nfp/flower/action.c:618 nfp_fl_pedit()
error: uninitialized symbol 'idx'.
Which is actually never used from the functions that take it as
parameter. Remove it.
Fixes: 7386788175 ("drivers: net: use flow action infrastructure")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Fox <pfox@solarflare.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now ipvlan has a hard dependency on CONFIG_NETFILTER and
otherwise it cannot be built. However, the only ipvlan operation
mode that actually depends on netfilter is l3s, everything else
is independent of it. Break this hard dependency such that users
are able to use ipvlan l3 mode on systems where netfilter is not
compiled in.
Therefore, this adds a hidden CONFIG_IPVLAN_L3S bool which is
defaulting to y when CONFIG_NETFILTER is set in order to retain
existing behavior for l3s. All l3s related code is refactored
into ipvlan_l3s.c that is compiled in when enabled.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Martynas Pumputis <m@lambda.lt>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let genphy_c45_read_link manage the devices to check, this removes
overhead from callers. Add C22EXT to the list of excluded devices
because it doesn't implement the status register. According to the
802.3 clause 45 spec registers 29.0 - 29.4 are reserved.
At the moment we have very few clause 45 PHY drivers, so we are
lacking experience whether other drivers will have to exclude further
devices, or may need to check PHY XS. If we should figure out that
list of devices to check needs to be configurable, I think best will
be to add a device list member to struct phy_driver.
v2:
- adjusted commit message
- exclude also device C22EXT from link checking
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fixed_phy_register_with_gpiod() API. It lets users create a
fixed_phy instance that uses a GPIO descriptor which was obtained
externally e.g. through platform data.
This enables platform devices (non-DT based) to use GPIOs for link
status.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
Add comphy support for Armada 38x
This series adds support for the comphy for Armada 38x, which allows
these SoCs to use 2500BASE-X mode with appropriate SFP modules.
Tested on SolidRun Clearfog after updating for the 5.0 merge window
changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the comphy settings for the Ethernet interfaces.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the common phy binding, so that we can reconfigure the
comphy according to the desired ethernet speed. This will allow us to
support 1000base-X and 2500base-X SFPs dynamically on SolidRun Clearfog.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an optional phys property to the mvneta binding documentation for
the common phy.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the DT description for the Armada 38x common phy.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Armada 38x common phy to allow us to change the
speed of the Ethernet serdes lane. This driver only supports
manipulation of the speed, it does not support configuration of the
common phy.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Marvell Armada 38x common phy bindings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
net/smc: patches 2019-02-07
here are patches for SMC:
* patches 1, 3, and 6 are cleanups without functional change
* patch 2 postpones closing of internal clcsock
* patches 4 and 5 improve link group creation locking
* patch 7 restores AF_SMC as diag_family field
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ed75986f4a ("net/smc: ipv6 support for smc_diag.c") changed the
value of the diag_family field. The idea was to indicate the family of
the IP address in the inet_diag_sockid field. But the change makes it
impossible to distinguish an inet_sock_diag response message from SMC
sock_diag response. This patch restores the original behaviour and sends
AF_SMC as value of the diag_family field.
Fixes: ed75986f4a ("net/smc: ipv6 support for smc_diag.c")
Reported-by: Eugene Syromiatnikov <esyr@redhat.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lgr field of an smc_connection is set in smc_conn_create() and
should be cleared in smc_conn_free() for consistency reasons, so move
the responsible code.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SMC client and server connections are both established at the same
time, smc_connect_rdma() cannot send a CLC confirm message while
smc_listen_work() is waiting for one due to lock contention. This can
result in timeouts in smc_clc_wait_msg() and failed SMC connections.
In case of SMC-R, there are two types of LGRs (client and server LGRs)
which can be protected by separate locks. So, this patch splits the LGR
pending lock into two separate locks for client and server to avoid the
locking issue for SMC-R.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SMC client and server connections are both established at the same
time, smc_connect_ism() cannot send a CLC confirm message while
smc_listen_work() is waiting for one due to lock contention. This can
result in timeouts in smc_clc_wait_msg() and failed SMC connections.
In case of SMC-D, the LGR pending lock is not needed while
smc_listen_work() is waiting for the CLC confirm message. So, this patch
releases the lock earlier for SMC-D to avoid the locking issue.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC already provides a wrapper for atomic64 calls to be
architecture independent. Use this wrapper for SMC-D as well.
Reported-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to RFC7609 (http://www.rfc-editor.org/info/rfc7609)
first the SMC-R connection is shut down and then the normal TCP
connection FIN processing drives cleanup of the internal TCP connection.
The unconditional release of the clcsock during active socket closing
has to be postponed if the peer has not yet signalled socket closing.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to define these PNETID related constants in
the pnet.h file, since they are just used locally within pnet.c.
Just code cleanup, no functional change.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an rdst is rejected by a driver, the current code removes it from
the remote list, but neglects to free it. This is triggered by
tools/testing/selftests/drivers/net/mlxsw/vxlan_fdb_veto.sh and shows as
the following kmemleak trace:
unreferenced object 0xffff88817fa3d888 (size 96):
comm "softirq", pid 0, jiffies 4372702718 (age 165.252s)
hex dump (first 32 bytes):
02 00 00 00 c6 33 64 03 80 f5 a2 61 81 88 ff ff .....3d....a....
06 df 71 ae ff ff ff ff 0c 00 00 00 04 d2 6a 6b ..q...........jk
backtrace:
[<00000000296b27ac>] kmem_cache_alloc_trace+0x1ae/0x370
[<0000000075c86dc6>] vxlan_fdb_append.part.12+0x62/0x3b0 [vxlan]
[<00000000e0414b63>] vxlan_fdb_update+0xc61/0x1020 [vxlan]
[<00000000f330c4bd>] vxlan_fdb_add+0x2e8/0x3d0 [vxlan]
[<0000000008f81c2c>] rtnl_fdb_add+0x4c2/0xa10
[<00000000bdc4b270>] rtnetlink_rcv_msg+0x6dd/0x970
[<000000006701f2ce>] netlink_rcv_skb+0x290/0x410
[<00000000c08a5487>] rtnetlink_rcv+0x15/0x20
[<00000000d5f54b1e>] netlink_unicast+0x43f/0x5e0
[<00000000db4336bb>] netlink_sendmsg+0x789/0xcd0
[<00000000e1ee26b6>] sock_sendmsg+0xba/0x100
[<00000000ba409802>] ___sys_sendmsg+0x631/0x960
[<000000003c332113>] __sys_sendmsg+0xea/0x180
[<00000000f4139144>] __x64_sys_sendmsg+0x78/0xb0
[<000000006d1ddc59>] do_syscall_64+0x94/0x410
[<00000000c8defa9a>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
Move vxlan_dst_free() up and schedule a call thereof to plug this leak.
Fixes: 61f46fe8c6 ("vxlan: Allow vetoing of FDB notifications")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha says:
====================
Devlink health reporting and recovery system
The health mechanism is targeted for Real Time Alerting, in order to know when
something bad had happened to a PCI device
- Provide alert debug information
- Self healing
- If problem needs vendor support, provide a way to gather all needed debugging
information.
The main idea is to unify and centralize driver health reports in the
generic devlink instance and allow the user to set different
attributes of the health reporting and recovery procedures.
The devlink health reporter:
Device driver creates a "health reporter" per each error/health type.
Error/Health type can be a known/generic (eg pci error, fw error, rx/tx error)
or unknown (driver specific).
For each registered health reporter a driver can issue error/health reports
asynchronously. All health reports handling is done by devlink.
Device driver can provide specific callbacks for each "health reporter", e.g.
- Recovery procedures
- Diagnostics and object dump procedures
- OOB initial attributes
Different parts of the driver can register different types of health reporters
with different handlers.
Once an error is reported, devlink health will do the following actions:
* A log is being send to the kernel trace events buffer
* Health status and statistics are being updated for the reporter instance
* Object dump is being taken and saved at the reporter instance (as long as
there is no other dump which is already stored)
* Auto recovery attempt is being done. Depends on:
- Auto-recovery configuration
- Grace period vs. time passed since last recover
The user interface:
User can access/change each reporter attributes and driver specific callbacks
via devlink, e.g per error type (per health reporter)
- Configure reporter's generic attributes (like: Disable/enable auto recovery)
- Invoke recovery procedure
- Run diagnostics
- Object dump
The devlink health interface (via netlink):
DEVLINK_CMD_HEALTH_REPORTER_GET
Retrieves status and configuration info per DEV and reporter.
DEVLINK_CMD_HEALTH_REPORTER_SET
Allows reporter-related configuration setting.
DEVLINK_CMD_HEALTH_REPORTER_RECOVER
Triggers a reporter's recovery procedure.
DEVLINK_CMD_HEALTH_REPORTER_DIAGNOSE
Retrieves diagnostics data from a reporter on a device.
DEVLINK_CMD_HEALTH_REPORTER_DUMP_GET
Retrieves the last stored dump. Devlink health
saves a single dump. If an dump is not already stored by the devlink
for this reporter, devlink generates a new dump.
dump output is defined by the reporter.
DEVLINK_CMD_HEALTH_REPORTER_DUMP_CLEAR
Clears the last saved dump file for the specified reporter.
netlink
+--------------------------+
| |
| + |
| | |
+--------------------------+
|request for ops
|(diagnose,
mlx5_core devlink |recover,
|dump)
+--------+ +--------------------------+
| | | reporter| |
| | | +---------v----------+ |
| | ops execution | | | |
| <----------------------------------+ | |
| | | | | |
| | | + ^------------------+ |
| | | | request for ops |
| | | | (recover, dump) |
| | | | |
| | | +-+------------------+ |
| | health report | | health handler | |
| +-------------------------------> | |
| | | +--------------------+ |
| | health reporter create | |
| +----------------------------> |
+--------+ +--------------------------+
In this patchset, mlx5e TX reporter is implemented.
Cmdline format:
devlink health show [DEV reporter REPORTE_NAME]
devlink health recover DEV reporter REPORTER_NAME
devlink health diagnose DEV reporter REPORTER_NAME
devlink health dump show DEV reporter REPORTER_NAME
devlink health dump clear DEV reporter REPORTER_NAME
devlink health set DEV reporter REPORTER_NAME NAME VALUE
Cmdline examples:
$devlink health show
pci/0000:00:09.0:
name tx
state healthy #err 1 #recover 0 last_dump_ts N/A
parameters:
grace_period 500 auto_recover false
$devlink health diagnose pci/0000:00:09.0 reporter tx -j -p
{
"SQs": [ {
"sqn": 138,
"HW state": 1,
"stopped": false
},{
"sqn": 142,
"HW state": 1,
"stopped": false
} ]
}
$devlink health diagnose pci/0000:00:09.0 reporter tx
SQs:
sqn: 138 HW state: 1 stopped: false
sqn: 142 HW state: 1 stopped: false
$devlink health recover pci/0000:00:09 reporter tx
$devlink health set pci/0000:00:09.0 reporter tx grace_period 3500
$devlink health set pci/0000:00:09.0 reporter tx auto_recover false
Changelog:
v4:
- Rebase on latest net-next
- Remove trace_devlink_health signature exposure in case CONFIG_NET_DEVLINK is
not defined as it shall only be used from devlink.
v3:
- Redesign of devlink <-> driver fmsg API
- Various bug fixes
v2:
- Remove FW* reporters to decrease the amount of patches in the patchset
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new file to add information about devlink health
mechanism.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, ndo_tx_timeout callback will be redirected to the tx
reporter in order to detect a tx timeout error and report it to the
devlink health. (The watchdog detects tx timeouts, but the driver verify
the issue still exists before launching any recover method).
In addition, recover from tx timeout in case of lost interrupt was added
to the tx reporter recover method. The tx timeout recover from lost
interrupt is not a new feature in the driver, this patch re-organize the
functionality and move it to the tx reporter recovery flow.
tx timeout example:
(with auto_recover set to false, if set to true, the manual recover and
diagnose sections are irrelevant)
$cat /sys/kernel/debug/tracing/trace
...
devlink_health_report: bus_name=pci dev_name=0000:00:09.0
driver_name=mlx5_core reporter_name=tx: TX timeout on queue: 0, SQ: 0x8a,
CQ: 0x35, SQ Cons: 0x2 SQ Prod: 0x2, usecs since last trans: 14912000
$devlink health show
pci/0000:00:09.0:
name tx
state healthy #err 1 #recover 0 last_dump_ts N/A
parameters:
grace_period 500 auto_recover false
$devlink health diagnose pci/0000:00:09.0 reporter tx -j -p
{
"SQs": [ {
"sqn": 138,
"HW state": 1,
"stopped": true
},{
"sqn": 142,
"HW state": 1,
"stopped": false
} ]
}
$devlink health diagnose pci/0000:00:09.0 reporter tx
SQs:
sqn: 138 HW state: 1 stopped: true
sqn: 142 HW state: 1 stopped: false
$devlink health recover pci/0000:00:09 reporter tx
$devlink health show
pci/0000:00:09.0:
name tx
state healthy #err 1 #recover 1 last_dump_ts N/A
parameters:
grace_period 500 auto_recover false
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mlx5e tx reporter to devlink health reporters. This reporter will be
responsible for diagnosing, reporting and recovering of tx errors.
This patch declares the TX reporter operations and creates it using the
devlink health API. Currently, this reporter supports reporting and
recovering from send error CQE only. In addition, it adds diagnose
information for the open SQs.
For a local SQ recover (due to driver error report), in case of SQ recover
failure, the recover operation will be considered as a failure.
For a full tx recover, an attempt to close and open the channels will be
done. If this one passed successfully, it will be considered as a
successful recover.
The SQ recover from error CQE flow is not a new feature in the driver,
this patch re-organize the functions and adapt them for the devlink
health API. For this purpose, move code from en_main.c to a new file
named reporter_tx.c.
Diagnose output:
$devlink health diagnose pci/0000:00:09.0 reporter tx -j -p
{
"SQs": [ {
"sqn": 138,
"HW state": 1,
"stopped": false
},{
"sqn": 142,
"HW state": 1,
"stopped": false
} ]
}
$devlink health diagnose pci/0000:00:09.0 reporter tx
SQs:
sqn: 138 HW state: 1 stopped: false
sqn: 142 HW state: 1 stopped: false
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health dump commands, in order to run an dump operation
over a specific reporter.
The supported operations are dump_get in order to get last saved
dump (if not exist, dump now) and dump_clear to clear last saved
dump.
It is expected from driver's callback for diagnose command to fill it
via the devlink fmsg API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health diagnose command, in order to run a diagnose
operation over a specific reporter.
It is expected from driver's callback for diagnose command to fill it
via the devlink fmsg API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health recover command to the uapi, in order to allow the user
to execute a recover operation over a specific reporter.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health set command, in order to set configuration parameters
for a specific reporter.
Supported parameters are:
- graceful_period: Time interval between auto recoveries (in msec)
- auto_recover: Determines if the devlink shall execute recover upon
receiving error for the reporter
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health get command to provide reporter/s data for user space.
Add the ability to get data per reporter or dump data from all available
reporters.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon error discover, every driver can report it to the devlink health
mechanism via devlink_health_report function, using the appropriate
reporter registered to it. Driver can pass error specific context which
will be delivered to it as part of the dump / recovery callbacks.
Once an error is reported, devlink health will do the following actions:
* A log is being send to the kernel trace events buffer
* Health status and statistics are being updated for the reporter instance
* Object dump is being taken and stored at the reporter instance (as long
as there is no other dump which is already stored)
* Auto recovery attempt is being done. Depends on:
- Auto Recovery configuration
- Grace period vs. Time since last recover
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink health reporter is an instance for reporting, diagnosing and
recovering from run time errors discovered by the reporters.
Define it's data structure and supported operations.
In addition, expose devlink API to create and destroy a reporter.
Each devlink instance will hold it's own reporters list.
As part of the allocation, driver shall provide a set of callbacks which
will be used by devlink in order to handle health reports and user
commands related to this reporter. In addition, driver is entitled to
provide some priv pointer, which can be fetched from the reporter by
devlink_health_reporter_priv function.
For each reporter, devlink will hold a metadata of statistics,
dump msg and status.
For passing dumps and diagnose data to the user-space, it will use devlink
fmsg API.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink fmsg is a mechanism to pass descriptors between drivers and
devlink, in json-like format. The API allows the driver to add nested
attributes such as object, object pair and value array, in addition to
attributes such as name and value.
Driver can use this API to fill the fmsg context in a format which will be
translated by the devlink to the netlink message later.
There is no memory allocation in advance (other than the initial list
head), and it dynamically allocates messages descriptors and add them to
the list on the fly.
When it needs to send the data using SKBs to the netlink layer, it
fragments the data between different SKBs. In order to do this
fragmentation, it uses virtual nests attributes, to avoid actual
nesting use which cannot be divided between different SKBs.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix fixed_phy not checking GPIO if no link_update callback
is registered.
In the original version all users registered a link_update
callback so the issue was masked.
Fixes: a5597008db ("phy: fixed_phy: Add gpio to determine link up/down.")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC driver had a custom IBM_EMAC_RX_SKB_HEADROOM
Kconfig option that reserved additional skb headroom for RX.
This patch removes the option and migrates the code
to use napi_alloc_skb() and netdev_alloc_skb_ip_align()
in its place.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's make genphy_c45_read_link behave the same as genphy_update_link
and set phydev->link in the function directly. This allows to simplify
the callers. In addition don't check further devices once we detect
that at least one device reports link as down.
v2:
- remove an unused variable
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver only enables Pdelay_Req and Pdelay_Resp when
HWTSTAMP_FILTER_PTP_V2_EVENT, HWTSTAMP_FILTER_PTP_V1_L4_EVENT or
HWTSTAMP_FILTER_PTP_V2_L4_EVENT is requested. This results in ptp sync on
slave mode to report 'received SYNC without timestamp' when using ptp4l.
Although the hardware can support Sync, Pdelay_Req and Pdelay_resp by
setting bit14 annd bits 17/16 to 01 this leaves Delay_Req timestamps out.
Fix this by enabling all event and general messages timestamps.
This includes SYNC, Follow_Up, Delay_Req, Delay_Resp, Pdelay_Req,
Pdelay_Resp and Pdelay_Resp_Follow_Up messages.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On one hand, the mv88e6xxx driver has a work queue called in loop
which will attempt register accesses after MDIO bus suspension, that
entirely freezes the platform during suspend.
On the other hand, the DSA core is not ready yet to support suspend to
RAM operation because so far there is no way to recover reliably the
switch configuration.
To avoid the kernel to freeze when suspending with a switch driven by
the mv88e6xxx driver, we choose to prevent the driver suspension and
in the same way, the whole platform.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Shilimkar says:
====================
rds: add tos support
RDS applications make use of tos to classify database traffic.
This feature has been used in shipping products from 2.6.32 based
kernels. Its tied with RDS v4.1 protocol version and the compatibility
gets negotiated as part of connections setup.
Patchset keeps full backward compatibility using existing connection
negotiation scheme. Currently the feature is exploited by RDMA
transport and for TCP transport the user tos values are mapped to
same default class (0).
For RDMA transports, RDMA CM service type API is used to
set up different SL(service lanes) and the IB fabric is configured
for tos mapping using Subnet Manager(SL to VL mappings).
Similarly for ROCE fabric, user priority is mapped with different
DSCP code points which are associated with different switch queues
in the fabric.
The original code was developed by Bang Nguyen in downstream kernel back in
2.6.32 kernel days and it has evolved significantly over period of time.
Thanks to Yanjun for doing testing with various combinations of host like
v3.1<->v4.1, v4.1.<->v3.1, v4.1 upstream to shipping v4.1 etc etc
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-02-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a riscv64 JIT for BPF, from Björn.
2) Implement BTF deduplication algorithm for libbpf which takes BTF type
information containing duplicate per-compilation unit information and
reduces it to an equivalent set of BTF types with no duplication and
without loss of information, from Andrii.
3) Offloaded and native BPF XDP programs can coexist today, enable also
offloaded and generic ones as well, from Jakub.
4) Expose various BTF related helper functions in libbpf as API which
are in particular helpful for JITed programs, from Yonghong.
5) Fix the recently added JMP32 code emission in s390x JIT, from Heiko.
6) Fix BPF kselftests' tcp_{server,client}.py to be able to run inside
a network namespace, also add a fix for libbpf to get libbpf_print()
working, from Stanislav.
7) Fixes for bpftool documentation, from Prashant.
8) Type cleanup in BPF kselftests' test_maps.c to silence a gcc8 warning,
from Breno.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Offload blackhole routes
Blackhole routes are routes that cause matching packets to be silently
dropped. This is in contrast to unreachable routes that generate an ICMP
host unreachable packet in response.
The driver currently programs both route types with a trap action and
lets the kernel drop matching packets. This is sub-optimal as packets
routed using a blackhole route can be directly dropped by the ASIC.
Patch #1 alters mlxsw to program blackhole routes with a discard action.
Patch #2 adds a matching test.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a simple topology consisting of two hosts directly connected to a
router. Make sure IPv4/IPv6 ping works and then add blackhole routes.
Test that ping fails and that the routes are marked as offloaded. Use a
simple tc filter to test that packets were dropped by the ASIC and not
trapped to the CPU.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new FIB entry type for blackhole routes and set it in case the
type of the notified route is 'RTN_BLACKHOLE'.
Program such routes with a discard action and mark them as offloaded
since the device is dropping the packets instead of the kernel.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: Introduce ndo_get_port_parent_id()
Based on discussion with Ido and feedback from Jakub there are clearly
two classes of users that implement SWITCHDEV_ATTR_ID_PORT_PARENT_ID:
- PF/VF drivers which typically only implement return the port's parent
ID, yet have to implement switchdev_port_attr_get() just for that
- Ethernet switch drivers: mlxsw, ocelot, DSA, etc. which implement more
attributes which we want to be able to eventually veto in the context
of the caller, thus making them candidates for using a blocking notifier
chain
Changes in v4:
- remove superfluous net/switchdev.h inclusions in a few files
- added Jiri's Acked-by where given
- removed err = -EOPNOTSUPP initializations
- changed according to Jiri's suggestion in net/ipv4/ipmr.c
Changes in v3:
- keep ethsw's switchdev_ops assignment
- remove inclusion of net/switchdev.h in netdevsim which is no longer
necesary
Changes in v2:
- resolved build failures spotted by kbuild test robot
- added helpers functions into the core network device layer:
dev_get_port_parent_id() and netdev_port_same_parent_id();
- added support for recursion to lower devices
Changes from RFC:
- introduce a ndo_get_port_parent_id() and convert all relevant drivers
to use it
- get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID
A subsequent set of patches will convert switchdev_port_attr_set() to
use a blocking notifier call, and still get rid of
switchdev_port_attr_get() altogether.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a dedicated NDO for getting a port's parent ID, get rid
of SWITCHDEV_ATTR_ID_PORT_PARENT_ID and convert all callers to use the
NDO exclusively. This is a preliminary change to getting rid of
switchdev_ops eventually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdevsim only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().
Since NFP uses switchdev_port_same_parent_id() convert it to use
netdev_port_same_parent_id().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
