RTL8168dp is ancient anyway, and I haven't seen any trace of its early
version 27 yet. This chip versions needs quite some special handling,
therefore it would facilitate driver maintenance if support for it
could be dropped. For now just disable detection of this chip version.
If nobody complains we can remove support for it in the near future.
v2:
- extend unknown chip version error message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/ca98f018-a0e1-8762-e95c-f0ad773a0271@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If WOL isn't enabled, then there's no need to enable wakeup from D3
on system shutdown.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use WARN_ONCE here to get a call trace in case of a problem.
This facilitates finding the offending code part.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use WARN here to avoid stopping the system. In addition print the addr
and mask values that triggered the warning.
v2:
- return on WARN to avoid an invalid register write
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MC firmware takes these PAUSE/ASYM_PAUSE flags provided by the
driver, transforms them back into rx/tx pause enablement status and
applies them to hardware. We are not losing information by this
transformation, thus remove the comment.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dpaa2-eth driver has phylink integration only if the connected dpmac
object is in TYPE_PHY (aka the PCS/PHY etc link status is managed by
Linux instead of the firmware). The check is thus unnecessary because
the code path that reaches the .mac_link_up() callback is only with
TYPE_PHY dpmac objects.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The fsl_mc_get_endpoint() function now returns -EPROBE_DEFER when the
dpmac device was not yet discovered by the fsl-mc bus. When this
happens, pass the error code up so that we can retry the probe at a
later time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the network interface object is connected to a MAC of TYPE_FIXED, the
link status management is handled exclusively by the firmware. This does
not mean that the driver cannot access the MAC counters and export them
in ethtool.
For this to happen, we open the attached dpmac device and keep a pointer
to it in priv->mac. Because of this, all the checks in the driver of the
following form 'if (priv->mac)' have to be updated to actually check
the dpmac attribute and not rely on the presence of a non-NULL value.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Split up the initialization phase of the dpmac object from actually
configuring the phylink instance, connecting to it and configuring the
MAC. This is done so that even though the dpni object is connected to a
dpmac which has link management handled by the firmware we are still
able to export the MAC counters.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
napi_gro_receive() can never return GRO_DROP
GRO_DROP can only be returned from napi_gro_frags()
which is the other NAPI GRO entry point.
Followup patch will remove GRO_DROP, because drivers
are not supposed to call napi_gro_frags() if prior
napi_get_frags() has failed.
Note that I have left the gro_dropped variable. I leave to ice
maintainers the decision to further remove it from ethtool -S results.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit b27507bb59 ("net/ibmvnic: unlock rtnl_lock in reset so
linkwatch_event can run") introduced do_change_param_reset function to
solve the rtnl lock issue. Majority of the code in do_change_param_reset
duplicates do_reset. Also, we can handle the rtnl lock issue in do_reset
itself. Hence merge do_change_param_reset back into do_reset to clean up
the code.
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20210106213514.76027-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "undocumented" annotations in the EtherAVB driver were done against
the R-Car gen2 manuals; most of these registers/bits were then described
in the R-Car gen3 manuals -- reflect this fact in the annotations (note
that ECSIPR.LCHNGIP was documented in the recent R-Car gen2 manual)...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the R-Car Series, 3rd Generation User's Manual: Hardware,
Rev. 1.50, there's no APSR.DM field, instead there are 2 independent
RX/TX clock internal delay bits. Follow the suit: remove #define APSR_DM
and rename #define's APSR_DM_{R|T}DM to APSR_{R|T}DM.
While at it, do several more things to the declaration of *enum* APSR_BIT:
- remove superfluous indentation;
- annotate APSR_MEMS as undocumented;
- annotate APSR as R-Car Gen3 only.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed says:
====================
mlx5 fixes 2021-01-07
* tag 'mlx5-fixes-2021-01-07' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Fix memleak in mlx5e_create_l2_table_groups
net/mlx5e: Fix two double free cases
net/mlx5: Release devlink object if adev fails
net/mlx5e: ethtool, Fix restriction of autoneg with 56G
net/mlx5e: In skb build skip setting mark in switchdev mode
net/mlx5: E-Switch, fix changing vf VLANID
net/mlx5e: Fix SWP offsets when vlan inserted by driver
net/mlx5e: CT: Use per flow counter when CT flow accounting is enabled
net/mlx5: Use port_num 1 instead of 0 when delete a RoCE address
net/mlx5e: Add missing capability check for uplink follow
net/mlx5: Check if lag is supported before creating one
====================
Link: https://lore.kernel.org/r/20210107202845.470205-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CPL_ABORT_RPL is sent after releasing the resources by calling
chtls_release_resources(sk); and chtls_conn_done(sk);
eventually causing kernel panic. Fixing it by calling release
in appropriate order.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of server removal lookup_stid() may return NULL pointer, which
is used as listen_ctx. So added a check before accessing this pointer.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The skb is unlinked twice, one in __skb_dequeue in function
chtls_reset_synq() and another in cleanup_syn_rcv_conn().
So in this patch using skb_peek() instead of __skb_dequeue(),
so that unlink will be handled only in cleanup_syn_rcv_conn().
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In chtls_pass_accept_request(), removing the chtls_reqsk_free()
call to avoid oreq freeing twice. Here oreq is the pointer to
struct request_sock.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If route to peer is not configured, we might get non tls
devices from dst_neigh_lookup() which is invalid, adding a
check to avoid it.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At the time of SYN_RECV, connection information is not
initialized at FW, updating tcb flag over uninitialized
connection causes adapter crash. We don't need to
update the flag during SYN_RECV state, so avoid this.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
send_abort_rpl() is not calculating cpl_abort_req_rss offset and
ends up sending wrong TID with abort_rpl WR causng tid leaks.
Replaced send_abort_rpl() with chtls_send_abort_rpl() as it is
redundant.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amlogic Meson G12A (and newer: G12B, SM1) SoCs have a more advanced RX
delay logic. Instead of fine-tuning the delay in the nanoseconds range
it now allows tuning in 200 picosecond steps. This support comes with
new bits in the PRG_ETH1[19:16] register.
Add support for validating the RGMII RX delay as well as configuring the
register accordingly on these platforms.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Newer SoCs starting with the Amlogic Meson G12A have more a precise
RGMII RX delay configuration register. This means more complexity in the
code. Extract the existing RGMII delay configuration code into a
separate function to make it easier to read/understand even when adding
more logic in the future.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amlogic Meson G12A, G12B and SM1 SoCs have a more advanced RGMII RX
delay register which allows picoseconds precision. Parse the new
"rx-internal-delay-ps" property or fall back to the value from the old
"amlogic,rx-delay-ns" property.
No upstream DTB uses the old "amlogic,rx-delay-ns" property (yet).
Only include minimalistic logic to fall back to the old property,
without any special validation (for example if the old and new
property are given at the same time).
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The timing-adjustment clock only has to be enabled when a) there is a
2ns RX delay configured using device-tree and b) the phy-mode indicates
that the RX delay should be enabled.
Only enable the RX delay if both are true, instead of (by accident) also
enabling it when there's the 2ns RX delay configured but the phy-mode
incicates that the RX delay is not used.
Fixes: 9308c47640 ("net: stmmac: dwmac-meson8b: add support for the RX delay configuration")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SYSTEMPORT driver maps each port of the embedded Broadcom DSA switch
port to a certain queue of the master Ethernet controller. For that it
currently uses a dedicated notifier infrastructure which was added in
commit 60724d4bae ("net: dsa: Add support for DSA specific notifiers").
However, since commit 2f1e8ea726 ("net: dsa: link interfaces with the
DSA master to get rid of lockdep warnings"), DSA is actually an upper of
the Broadcom SYSTEMPORT as far as the netdevice adjacency lists are
concerned. So naturally, the plain NETDEV_CHANGEUPPER net device notifiers
are emitted. It looks like there is enough API exposed by DSA to the
outside world already to make the call_dsa_notifiers API redundant. So
let's convert its only user to plain netdev notifiers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is a bit strange to see something as specific as Broadcom SYSTEMPORT
bits in the main DSA include file. Move these away into a separate
header, and have the tagger and the SYSTEMPORT driver include them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to Realtek the ERI register 0x1a8 quirk is needed to work
around a hw issue with the PHY on RTL8168g. The register needs to be
changed before powering down the PHY. Currently we don't meet this
requirement, however I'm not aware of any problems caused by this.
Therefore I see the change as an improvement.
The PHY driver has no means to access the chip ERI registers,
therefore we have to intercept MDIO writes to BMCR register.
If the BMCR_PDOWN bit is going to be set, then let's apply the
quirk before actually powering down the PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No functional change here. We just move a code block to avoid a
function forward declaration in a subsequent change.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All UDP tunnel port management is now routed via udp_tunnel_nic
infra directly. Remove the old callbacks.
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use existing rx processed count to track against budget, thereby making
budget decrement operation redundant.
rx_desc_count can be calculated outside the rx loop, making the loop a
bit smaller.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can increase the efficiency of rx path by using buffers to receive
packets then build SKBs around them just before passing into the network
stack. In contrast, preallocating SKBs too early reduces CPU cache
efficiency.
Check if we're in NAPI context when refilling RX. Normally we're almost
always running in NAPI context. Dispatch to napi_alloc_frag directly
instead of relying on netdev_alloc_frag which does the same but
with the overhead of local_bh_disable/enable.
Tested on BCM6328 320 MHz and iperf3 -M 512 to measure packet/sec
performance. Included netif_receive_skb_list and NET_IP_ALIGN
optimizations.
Before:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.00 sec 49.9 MBytes 41.9 Mbits/sec 197 sender
[ 4] 0.00-10.00 sec 49.3 MBytes 41.3 Mbits/sec receiver
After:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-30.00 sec 171 MBytes 47.8 Mbits/sec 272 sender
[ 4] 0.00-30.00 sec 170 MBytes 47.6 Mbits/sec receiver
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rx SKB ring use the same code for cleanup at various points.
Combine them into a function to reduce lines of code.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When mlx5_create_flow_group() fails, ft->g should be
freed just like when kvzalloc() fails. The caller of
mlx5e_create_l2_table_groups() does not catch this
issue on failure, which leads to memleak.
Fixes: 33cfaaa8f3 ("net/mlx5e: Split the main flow steering table")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5e_create_ttc_table_groups() frees ft->g on failure of
kvzalloc(), but such failure will be caught by its caller
in mlx5e_create_ttc_table() and ft->g will be freed again
in mlx5e_destroy_flow_table(). The same issue also occurs
in mlx5e_create_ttc_table_groups(). Set ft->g to NULL after
kfree() to avoid double free.
Fixes: 7b3722fa9e ("net/mlx5e: Support RSS for GRE tunneled packets")
Fixes: 33cfaaa8f3 ("net/mlx5e: Split the main flow steering table")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Prior to this patch, configuring speed to 50G with autoneg off over
devices supporting 50G per lane failed.
Support for 50G per lane introduced a new set of link-modes, on which
driver always performed a speed validation as if only legacy link-modes
were configured. Fix driver speed validation to force setting autoneg
over 56G only if in legacy link-mode.
Fixes: 3d7cadae51 ("net/mlx5e: ethtool, Fix analysis of speed setting")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
sop_drop_qpn field in the cqe is used by two features, in SWITCHDEV mode
to restore the chain id in case of a miss and in LEGACY mode to support
skbedit mark action. In build RX skb, the skb mark field is set regardless
of the configured mode which cause a corruption of the mark field in case
of switchdev mode.
Fix by overriding the mark value back to 0 in the representor tc update
skb flow.
Fixes: 8f1e0b97cc ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Adding vf VLANID for the first time, or after having cleared previously
defined VLANID works fine, however, attempting to change an existing vf
VLANID clears the rules on the firmware, but does not add new rules for
the new vf VLANID.
Fix this by changing the logic in function esw_acl_egress_lgcy_setup()
so that it will always configure egress rules.
Fixes: ea651a86d4 ("net/mlx5: E-Switch, Refactor eswitch egress acl codes")
Signed-off-by: Alaa Hleihel <alaa@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In case WQE includes inline header the vlan is inserted by driver even
if vlan offload is set. On geneve over vlan interface where software
parser is used the SWP offsets should be updated according to the added
vlan.
Fixes: e3cfc7e6b7 ("net/mlx5e: TX, Add geneve tunnel stateless offload support")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Connection counters may be shared for both directions when the counter
is used for connection aging purposes. However, if TC flow
accounting is enabled then a unique counter is required per direction.
Instantiate a unique counter per direction if the conntrack accounting
extension is enabled. Use a shared counter when the connection accounting
extension is disabled.
Fixes: 1edae2335a ("net/mlx5e: CT: Use the same counter for both directions")
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
