Add sm1 support the axg audio clock controllers. This new version is
indeed derived from the previous generation, as always, adding a few
new clocks to the mix.
The number of gates now exceeds 32 and do not fit in a single register.
Unfortunately, designers chose to introduce the new gate register
immediately after the original one, at the beginning of the register
space, shifting all the master clock register offsets.
The sm1 also introduce a few mux and divider on the top clock path,
possibly to lower the peripheral clocks of the audio blocks if
necessary.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The peripheral clock on the sm1 goes through some muxes
and dividers before reaching the audio gates. To model that,
without repeating our self too much, the "top" clock signal
is introduced and will serve as a the parent of the gates.
On the axg and g12a, the top clock is just a pass-through to
the audio peripheral clock provided by the main controller.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Rearrange the macro definition of the clocks of the axg-audio
controller. Also, the sm1 variant will feature tiny modification
of different blocks in this controller. Because of that, we need
to fallback to the old way of defining parent for some of the
clocks, using signal name.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Since the addition of the g12a, the last register is
AUDIO_CLK_SPDIFOUT_B_CTRL.
Fixes: 075001385c ("clk: meson: axg-audio: add g12a support")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Defining the number of each input type is no longer necessary since
we are not using the clk-input hack anymore
Fixes: 282420eed2 ("clk: meson: axg-audio: migrate to the new parent description method")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
When setting the 100MHz, 500MHz, 666MHz and 1GHz rate for CPU clocks,
CCF will use the SYS_PLL to handle these frequencies, but:
- using FIXED_PLL derived FCLK_DIV2/DIV3 clocks is more precise
- the Amlogic G12A/G12B/SM1 Suspend handling in firmware doesn't
handle entering suspend using SYS_PLL for these frequencies
Adding CLK_MUX_ROUND_CLOSEST on all the muxes of the non-SYS_PLL
cpu clock tree helps CCF always selecting the FCLK_DIV2/DIV3 as source
for these frequencies.
Fixes: ffae8475b9 ("clk: meson: g12a: add notifiers to handle cpu clock change")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
CLK_SET_RATE_NO_REPARENT is wrongly set on the g12a cpu premux0 clocks
flags, and CLK_SET_RATE_PARENT is required for the g12a cpu premux0 clock
and the g12b cpub premux0 clock, otherwise CCF always selects the SYS_PLL
clock to feed the cpu cluster.
Fixes: ffae8475b9 ("clk: meson: g12a: add notifiers to handle cpu clock change")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The meson-saradc driver manually sets the input clock for
sar_adc_clk_sel. Update the GXBB clock driver (which is used on GXBB,
GXL and GXM) so the rate settings on sar_adc_clk_div are propagated up
to sar_adc_clk_sel which will let the common clock framework select the
best matching parent clock if we want that.
This makes sar_adc_clk_div consistent with the axg-aoclk and g12a-aoclk
drivers, which both also specify CLK_SET_RATE_PARENT.
Fixes: 33d0fcdfe0 ("clk: gxbb: add the SAR ADC clocks and expose them")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The Amlogic SM1 can set a dedicated clock frequency for each CPU core by
having a dedicate tree for each core similar to the CPU0 tree.
Like the DSU tree, a supplementaty mux has been added to use the CPU0
frequency instead.
But since the cluster only has a single power rail and shares a single PLL,
it's not worth adding 3 unsused clock tree, so we add only the mux to
select the CPU0 clock frequency for each CPU1, CPU2 and CPU3 cores.
They are set read-only because the early boot stages sets them to select
the CPU0 input clock.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The Amlogic SM1 DynamIQ Shared Unit has a dedicated clock tree similar to
the CPU clock tree with a supplementaty mux to select the CPU0 clock
instead.
Leave this as read-only since it's set up by the early boot stages.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the new GP1 PLL for the Amlogic SM1 SoC, used to feed the new
DynamIQ Shared Unit of the ARM Cores Complex.
This also adds a dedicated set of clock and compatible for SM1.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
On the g12a, the register space dedicated to the audio clock also
provides some resets. Let the clock controller register a reset
provider as well for this SoC family.
the axg SoC family does not appear to provide this feature.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
A future patch is going to change semantics of clk_register() so that
clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid
referencing this member here so that we don't run into NULL pointer
exceptions.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190731193517.237136-4-sboyd@kernel.org
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Expose the CPUB clock id to add DVFS to the second CPU cluster of
the Amlogic G12B SoC.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
In order to implement clock switching for the CLKID_CPU_CLK and
CLKID_CPUB_CLK, notifiers are added on specific points of the
clock tree :
cpu_clk / cpub_clk
| \- cpu_clk_dyn
| | \- cpu_clk_premux0
| | |- cpu_clk_postmux0
| | | |- cpu_clk_dyn0_div
| | | \- xtal/fclk_div2/fclk_div3
| | \- xtal/fclk_div2/fclk_div3
| \- cpu_clk_premux1
| |- cpu_clk_postmux1
| | |- cpu_clk_dyn1_div
| | \- xtal/fclk_div2/fclk_div3
| \- xtal/fclk_div2/fclk_div3
\ sys_pll / sys1_pll
This for each cluster, a single one for G12A, two for G12B.
Each cpu_clk_premux1 tree is marked as read-only and CLK_SET_RATE_NO_REPARENT,
to be used as "parking" clock in a safe clock frequency.
A notifier is added on each cpu_clk_premux0 to detech when CCF want to
change the frequency of the cpu_clk_dyn tree.
In this notifier, the cpu_clk_premux1 tree is configured to use the xtal
clock and then the cpu_clk_dyn is switch to cpu_clk_premux1 while CCF
updates the cpu_clk_premux0 tree.
A notifier is added on each sys_pll/sys1_pll to detect when CCF wants to
change the PLL clock source of the cpu_clk.
In this notifier, the cpu_clk is switched to cpu_clk_dyn while CCF
updates the sys_pll/sys1_pll frequency.
A third small notifier is added on each cpu_clk / cpub_clk and cpu_clk_dyn,
add a small delay at PRE_RATE_CHANGE/POST_RATE_CHANGE to let the other
notofiers change propagate before changing the cpu_clk_premux0 and sys_pll
clock trees.
This notifier set permits switching the cpu_clk / cpub_clk without any
glitches and using a safe parking clock while switching between sub-GHz
clocks using the cpu_clk_dyn tree.
This setup has been tested and validated on the Amlogic G12A and G12B
SoCs running the arm64 cpuburn at [1] and cycling between all the possible
cpufreq translations of each cluster and checking the final frequency using
the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add a clock driver for the cpu dynamic divider, this divider needs
to have a flag set before setting the divider value then removed
while writing the new value to the register.
This drivers implements this behavior and will be used essentially
on the Amlogic G12A and G12B SoCs for cpu clock trees.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The clk input function which allows clock controllers to register a bypass
clock from a clock producer is no longer needed anymore since meson clock
controllers have migrated to a new parent allocation method.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
During probe, bypass clocks (i.e. ee-in-xtal) are made from device-tree
inputs to provide input clocks which can be access through global name.
The cons of this method are the duplicated clocks, means more string
comparison.
Specify parent directly with device-tree clock name.
Remove the bypass clock registration from the ee probe function.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This clock controller use the string comparison method to describe parent
relation between the clocks, which is not optimized.
Migrate to the new way by using .parent_hws where possible (ie. when
all clocks are local to the controller) and use .parent_data otherwise.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This clock controller use the string comparison method to describe parent
relation between the clocks, which is not optimized.
Migrate to the new way by using .parent_hws where possible (ie. when
all clocks are local to the controller) and use .parent_data otherwise.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This clock controller use the string comparison method to describe parent
relation between the clocks, which is not optimized.
Migrate to the new way by using .parent_hws where possible (ie. when
all clocks are local to the controller) and use .parent_data otherwise.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This clock controller use the string comparison method to describe parent
relation between the clocks, which is not optimized.
Migrate to the new way by using .parent_hws where possible (ie. when
all clocks are local to the controller) and use .parent_data otherwise.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This clock controller use the string comparison method to describe parent
relation between the clocks, which is not optimized.
Migrate to the new way by using .parent_hws where possible (ie. when
all clocks are local to the controller) and use .parent_data otherwise.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
During probe, bypass clocks (i.e. ao-in-xtal) are made from device-tree
inputs to provide input clocks which can be access through global name.
The cons of this method are the duplicated clocks, means more string
comparison.
Specify parent directly with device-tree clock name.
Function to regiter bypass clocks is removed.
Input parameters from meson aoclk data structure are deprecated and then
deleted since all aoclk files are migrated.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This clock controller use the string comparison method to describe parent
relation between the clocks, which is not optimized.
Migrate to the new way by using .parent_hws where possible (when parent
clocks are localy declared in the controller) and use .parent_data
otherwise.
Remove clk input helper and all bypass clocks (declared in probe function)
which are no longer used since we are able to use device-tree clock name
directly.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This clock controller use the string comparison method to describe parent
relation between the clocks, which is not optimized.
Migrate to the new way by using .parent_hws where possible (when parent
clocks are localy declared in the controller) and use .parent_data
otherwise.
Remove clk input helper and all bypass clocks (declared in probe function)
which are no longer used since we are able to use device-tree clock name
directly.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This clock controller use the string comparison method to describe parent
relation between the clocks, which is not optimized.
Migrate to the new way by using .parent_hws where possible (when parent
clocks are localy declared in the controller) and use .parent_data
otherwise.
Remove clk input helper and all bypass clocks (declared in probe function)
which are no longer used since we are able to use device-tree clock name
directly.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This clock controller use the string comparison method to describe parent
relation between the clocks, which is not optimized. A recent patch [0]
allows parents to be specified without string names or with device-tree
clock name by using a new assignment structure.
Migrate to the new way by using .parent_hws where possible (when parent
clocks are localy declared in the controller) and use .parent_data
otherwise.
Remove clk input helper and all bypass clocks (declared in probe function)
which are no longer used since we are able to use device-tree clock name
directly.
[0] commit fc0c209c14 ("clk: Allow parents to be specified without string names")
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
[jbrunet@baylibre.com: remove CLK_SET_RATE_PARENT from mst muxes]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Replace hihi by hifi in the mali parent_names of the g12a SoC family.
Fixes: 085a4ea93d ("clk: meson: g12a: add peripheral clock controller")
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
- Do a DT/firmware lookup in clk_core_get() even when the DT index is a
nonsensical value
- Fix some clk data typos in the Amlogic DT headers/code
- Avoid returning junk in the TI clk driver when an invalid clk is
looked for
- Fix dividers for the emac clks on Stratix10 SoCs
- Fix default HDA rates on Tegra210 to correct distorted audio
-----BEGIN PGP SIGNATURE-----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=3QYB
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of clk driver fixes and one core framework fix
- Do a DT/firmware lookup in clk_core_get() even when the DT index is
a nonsensical value
- Fix some clk data typos in the Amlogic DT headers/code
- Avoid returning junk in the TI clk driver when an invalid clk is
looked for
- Fix dividers for the emac clks on Stratix10 SoCs
- Fix default HDA rates on Tegra210 to correct distorted audio"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: socfpga: stratix10: fix divider entry for the emac clocks
clk: Do a DT parent lookup even when index < 0
clk: tegra210: Fix default rates for HDA clocks
clk: ti: clkctrl: Fix returning uninitialized data
clk: meson: meson8b: fix a typo in the VPU parent names array variable
clk: meson: fix MPLL 50M binding id typo
On Amlogic Meson G12b platform, the fclk_div3 seems to be necessary for
the system to operate correctly.
Disabling it cause the entire system to freeze, including peripherals.
Let's mark this clock as critical, fixing boot on G12b platforms.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Update the Meson G12A Clock driver to support the Amlogic G12B SoC.
G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the
SYS_PLL are swapped between the clusters
- G12B has additional clocks like for CSI an other components
Here only the cpu clock tree is handled.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the TS clocks used by two temperature sensors
Reviewed-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> [fixed commit description]
Add the cts_i958 clock to control the clock source of the spdif output
block. It is used to select whether the clock source of the spdif output
is cts_amclk (when data are taken from i2s buffer) or the cts_mclk_i958
(when data are taken from the spdif buffer). The setup for this clock is
identical to GXBB, so this ports commit 7eaa44f620 ("clk: meson:
gxbb: add cts_i958 clock") to the Meson8/Meson8b/Meson8m2 clock driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the SPDIF master clock also referred as cts_mclk_i958. The setup for
this clock is identical to GXBB, so this ports commit 3c277c247e
("clk: meson: gxbb: add cts_mclk_i958") to the Meson8/Meson8b/Meson8m2
clock driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the I2S master clock also referred as cts_amclk. The setup for this
clock is identical to GXBB, so this ports commit 4087bd4b21 ("clk:
meson: gxbb: add cts_amclk") to the Meson8/Meson8b/Meson8m2 clock
driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the PLL and MPLL, the controller may require some magic setting to
be applied on startup.
This is needed when the initial setting is not applied by the boot ROM.
The controller need to do it when the setting applies to several clock,
like all the MPLLs in the case of g12a.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Until now (gx and axg), the mpll setting on boot (whatever the
bootloader) was good enough to generate a clean fractional division.
It is not the case on the g12a. While moving away from the vendor u-boot,
it was noticed the fractional part of the divider was no longer applied.
Like on the pll, some magic settings need to applied on the mpll
register.
This change adds the ability to do that on the mpll driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
After testing, it appears that the SSEN bit controls the spread
spectrum function on MPLL2, not MPLL0.
Fixes: 78b4af312f ("clk: meson-axg: add clock controller drivers")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The documentation says there is an SSEN bit on mpll0 but, after testing
it, no spread spectrum function appears to be enabled by this bit on any
of the MPLLs.
Let's remove it until we know more
Fixes: 1f737ffa13 ("clk: meson: mpll: fix mpll0 fractional part ignored")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The bit 'SSEN' available on some MPLL DSS outputs is not related to the
fractional part of the divider but to the function called
'Spread Spectrum'.
This function might be used to solve EM issues by adding a jitter on
clock signal. This widens the signal spectrum and weakens the peaks in it.
While spread spectrum might be useful for some application, it is
problematic for others, such as audio.
This patch introduce a new flag to the MPLL driver to enable (or not) the
spread spectrum function.
Fixes: 1f737ffa13 ("clk: meson: mpll: fix mpll0 fractional part ignored")
Tested-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The variable which holds the parent names for the VPU clocks has a typo
in it. Fix this typo to make the variable naming in the driver
consistent. No functional changes.
Fixes: 41785ce562 ("clk: meson: meson8b: add the VPU clock trees")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
MPLL_5OM (the capital letter o) should indeed be MPLL_50M (the number)
Fix this before it gets used.
Fixes: 25db146aa7 ("dt-bindings: clk: meson: add g12a periph clock controller bindings")
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
- Remove clk_readl() and introduce BE versions of basic clk types
* clk-doc:
clk: Drop duplicate clk_register() documentation
clk: Document and simplify clk_core_get_rate_nolock()
clk: Remove 'flags' member of struct clk_fixed_rate
clk: nxp: Drop 'flags' on fixed_rate clk macro
clk: Document __clk_mux_determine_rate()
clk: Document CLK_MUX_READ_ONLY mux flag
clk: Document deprecated things
clk: Collapse gpio clk kerneldoc
* clk-more-critical:
clk: highbank: Convert to CLK_IS_CRITICAL
* clk-meson: (21 commits)
clk: meson: axg-audio: add g12a support
clk: meson: axg-audio: don't register inputs in the onecell data
clk: meson: axg_audio: replace prefix axg by aud
dt-bindings: clk: axg-audio: add g12a support
clk: meson: meson8b: add the video decoder clock trees
clk: meson: meson8b: add the VPU clock trees
clk: meson: meson8b: add support for the GP_PLL clock on Meson8m2
clk: meson: meson8b: use a separate clock table for Meson8m2
dt-bindings: clock: meson8b: export the video decoder clocks
clk: meson-g12a: add video decoder clocks
dt-bindings: clock: meson8b: export the VPU clock
clk: meson-g12a: add PCIE PLL clocks
dt-bindings: clock: g12a-aoclk: expose CLKID_AO_CTS_OSCIN
clk: meson-pll: add reduced specific clk_ops for G12A PCIe PLL
dt-bindings: clock: meson8b: drop the "ABP" clock definition
clk: meson: g12a: add cpu clocks
dt-bindings: clk: g12a-clkc: add VDEC clock IDs
dt-bindings: clock: axg-audio: unexpose controller inputs
dt-bindings: clk: g12a-clkc: add PCIE PLL clock ID
clk: g12a-aoclk: re-export CLKID_AO_SAR_ADC_SEL clock id
...
* clk-basic-be:
clk: core: replace clk_{readl,writel} with {readl,writel}
clk: core: remove powerpc special handling
powerpc/512x: mark clocks as big endian
clk: mux: add explicit big endian support
clk: multiplier: add explicit big endian support
clk: gate: add explicit big endian support
clk: fractional-divider: add explicit big endian support
clk: divider: add explicit big endian support
