The phy_connect() function doesn't return NULL pointers. It returns
error pointers on error, so I have updated the check.
Fixes: 8425c41d1e ("net: ll_temac: Extend support to non-device-tree platforms")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit makes the kernel not send the next queued HCI command until
a command complete arrives for the last HCI command sent to the
controller. This change avoids a problem with some buggy controllers
(seen on two SKUs of QCA9377) that send an extra command complete event
for the previous command after the kernel had already sent a new HCI
command to the controller.
The problem was reproduced when starting an active scanning procedure,
where an extra command complete event arrives for the LE_SET_RANDOM_ADDR
command. When this happends the kernel ends up not processing the
command complete for the following commmand, LE_SET_SCAN_PARAM, and
ultimately behaving as if a passive scanning procedure was being
performed, when in fact controller is performing an active scanning
procedure. This makes it impossible to discover BLE devices as no device
found events are sent to userspace.
This problem is reproducible on 100% of the attempts on the affected
controllers. The extra command complete event can be seen at timestamp
27.420131 on the btmon logs bellow.
Bluetooth monitor ver 5.50
= Note: Linux version 5.0.0+ (x86_64) 0.352340
= Note: Bluetooth subsystem version 2.22 0.352343
= New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0) [hci0] 0.352344
= Open Index: 80:C5:F2:8F:87:84 [hci0] 0.352345
= Index Info: 80:C5:F2:8F:87:84 (Qualcomm) [hci0] 0.352346
@ MGMT Open: bluetoothd (privileged) version 1.14 {0x0001} 0.352347
@ MGMT Open: btmon (privileged) version 1.14 {0x0002} 0.352366
@ MGMT Open: btmgmt (privileged) version 1.14 {0x0003} 27.302164
@ MGMT Command: Start Discovery (0x0023) plen 1 {0x0003} [hci0] 27.302310
Address type: 0x06
LE Public
LE Random
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #1 [hci0] 27.302496
Address: 15:60:F2:91:B2:24 (Non-Resolvable)
> HCI Event: Command Complete (0x0e) plen 4 #2 [hci0] 27.419117
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #3 [hci0] 27.419244
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #4 [hci0] 27.420131
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #5 [hci0] 27.420259
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #6 [hci0] 27.420969
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #7 [hci0] 27.421983
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 4 {0x0003} [hci0] 27.422059
Start Discovery (0x0023) plen 1
Status: Success (0x00)
Address type: 0x06
LE Public
LE Random
@ MGMT Event: Discovering (0x0013) plen 2 {0x0003} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2 {0x0002} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2 {0x0001} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
BCM2076B1 appears to use 20:76:A0:00:56:79 as default address.
This address is used by at least 5 devices with the AMPAK AP6476
module and is also suspicious because it starts with the chip name
2076 (followed by a different revision A0 for some reason).
Add it to the list of default addresses and leave it up to the
user to configure a valid one.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The code works fine but the problem is that check for negatives is a
no-op:
if (arg < 0)
i = 0;
The "i" value isn't used. We immediately overwrite it with:
i = array_index_nospec(arg, MAX_LEC_ITF);
The array_index_nospec() macro returns zero if "arg" is out of bounds so
this works, but the dead code is confusing and it doesn't look very
intentional.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJczDAZAAoJEG4XJFUm622blLgH/jdBKEq9i1m5dtLi48u4sgPV
NsnPhR5XQjpbYpmvgPslKLxWzZq6A0P+lo9QqTXkP/QRyJLu7RnoY1c2wVsQbWaK
VTXc0cROzWt0ihAt8Mc/rEsZpISVnQ9mJbTd/kSJM9WlDeIg0jcJvnEAdQiEmM5t
2t+zZ5CupUXYbGE3zWHL1GSjBD9f0v7zyrNxYNGfvqhDEXhTFWAmVuRtfoAVlRU+
dt1HMv+qdxgoF6Uvaw/kgY09mDvdrfy2EVL0q7S3TKceute60SWf7de2sToI/rMQ
snUnVqTIIUnWPl6g+C3Bp2TbdZhy6XCSRsMFOVa2i1Lt+z1qe3dTr3hjxTQWRhE=
=uLaP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 03f66f0675 ("net: ethernet: ti: davinci_mdio: use devm_ioremap()")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to nla_nest_start_noflag can return null in the unlikely
event that nla_put returns -EMSGSIZE. Check for this condition to
avoid a null pointer dereference on pointer nla_reply.
Addresses-Coverity: ("Dereference null return value")
Fixes: 11efd5cb04 ("openvswitch: Support conntrack zone limit")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yi-Hung Wei <yihung.wei@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
ipv4: Move location of pcpu route cache and exceptions
This series moves IPv4 pcpu cached routes from fib_nh to fib_nh_common
to make the caches available for IPv6 nexthops (fib6_nh) with IPv4
routes. This allows a fib6_nh struct to be used with both IPv4 and
and IPv6 routes.
v4
- fixed memleak if encap_type is not set as noticed by Ido
v3
- dropped ipv6 patches for now. Will resubmit those once the existing
refcnt problem is fixed
v2
- reverted patch 2 to use ifdef CONFIG_IP_ROUTE_CLASSID instead
of IS_ENABLED(CONFIG_IP_ROUTE_CLASSID) to fix compile issues
reported by kbuild test robot
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the cached routes, make IPv4 exceptions accessible when
using an IPv6 nexthop struct with IPv4 routes. Simplify the exception
functions by passing in fib_nh_common since that is all it needs,
and then cleanup the call sites that have extraneous fib_nh conversions.
As with the cached routes this is a change in location only, from fib_nh
up to fib_nh_common; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the cached routes are in fib_nh_common, pass it to
rt_cache_route and simplify its callers. For rt_set_nexthop,
the tclassid becomes the last user of fib_nh so move the
container_of under the #ifdef CONFIG_IP_ROUTE_CLASSID.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the cached routes, nh_pcpu_rth_output and nh_rth_input, are IPv4
specific, a later patch wants to make them accessible for IPv6 nexthops
with IPv4 routes using a fib6_nh. Move the cached routes from fib_nh to
fib_nh_common and update references.
Initialization of the cached entries is moved to fib_nh_common_init,
and free is moved to fib_nh_common_release.
Change in location only, from fib_nh up to fib_nh_common; no functional
change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added freeing the old allocation of vf->qvlist_info in function
i40e_config_iwarp_qvlist before overwriting it with
the new allocation.
Signed-off-by: Martyna Szapar <martyna.szapar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed possible memory leak in i40e_vc_add_cloud_filter function:
cfilter is being allocated and in some error conditions
the function returns without freeing the memory.
Fix of integer truncation from u16 (type of queue_id value) to u8
when calling i40e_vc_isvalid_queue_id function.
Signed-off-by: Martyna Szapar <martyna.szapar@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable size is not necessary, hence it
is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The reason of this revert is unexpected issue found in NVM Update tool
during NVM image downgrade. The implementation is no longer needed
since the QV tools are already aware of new FW double ShadowRAM dump
mechanism.
This patch reverts ShadowRAM checksum calculation change introduced in
commit 9d12f0c4e436 ("i40e: Revert ShadowRAM checksum calculation change")
Signed-off-by: Maciej Paczkowski <maciej.paczkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Patch is adding missing input validation on VF message handling
by the PF to the functions with opcodes:
VIRTCHNL_OP_CONFIG_VSI_QUEUES = 6
VIRTCHNL_OP_CONFIG_IRQ_MAP = 7,
VIRTCHNL_OP_DISABLE_QUEUES = 9,
VIRTCHNL_OP_CONFIG_PROMISCUOUS_MODE = 14,
Signed-off-by: Martyna Szapar <martyna.szapar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New device ids are created to support X710 backplane and SFP+ cards.
This patch adds in i40e driver support for 2.5GbaseT and 5GbaseT speed.
It's implemented by checking I40E_CAP_PHY_TYPE_2_5GBASE_T,
I40E_CAP_PHY_TYPE_5GBASE_T bits from f/w and setting corresponding bits
in ethtool link ksettings supported and advertising masks.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In this patch fixed wrong truncation method from u16 to u8 during
validation.
It was changed by changing u8 to u32 parameter in method declaration
and arguments were changed to u32.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Field num_vectors from struct virtchnl_iwarp_qvlist_info should not be
larger than num_msix_vectors_vf in the hw struct. The iwarp uses the
same set of vectors as the LAN VF driver.
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the typo in I40E_CAP_PHY_TYPE mode link code.
It was fixed by changing 40000baseLR4_Full to 40000baseKR4_Full
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a bug where changing VLAN to 0 was not set until VF
restart.
Now we are setting pvid info to 0 when we have to change VLAN to 0.
Without this change when VF VLAN was changed to 0 nothing happened until
VF restart. For changing to VLAN different than 0 it worked correctly.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New device ids are created to support X710/XXV710 N3000 cards.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a bug where the promiscuous mode was not being
kept when the VF switched to a new VLAN.
Now we are config two times a promiscuous mode when we switch VLAN.
Without this change when we change VF VLAN we still receive
all the packets from previous VLAN and only unicast from new VLAN.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delete code that add default Tx rule on PF. With this rule PF can see
Tx VF traffic that should go outside. For traffic from VF to another
VF default Tx rule on PF doesn't apply because of lower priority than
VF mac rule.
With this change on PF in promisc mode we can see only Rx traffic that
doesn't match any other rule (mac etc.). We can't see Tx traffic from
other VSI.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move a bunch of members around to make more efficient use of
memory, eliminating holes where possible. None of these members
are hot path so cache line alignment is not very important here.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was converted to not use bool, but it was
neglected that the bools should have been converted to bit fields
as bit fields in software structures are ok, as long as they
use the correct kinds of unsigned types. This avoids
wasting lots of storage space to store single bit values.
One of the change hunks moves a variable lport out of
a group of "combinable" bit fields because all bits of
the u8 lport are valid and the variable can be packed in the
struct in struct holes.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds function to program VSI with ethertype based filter rule,
so that all flow control frames would be disallowed from being transmitted
to the client, in order to prevent malicious VSI, especially VF from
sending out PAUSE or PFC frames, and then control other VSIs traffic.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set features can have multiple features turned on|off in a single
call. Grouping these all in an if/else means after one condition
is met, other conditions/features will not be evaluated. Break
the if/else statements by feature to ensure all features will be
handled properly.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable netdev is being used in this function; remove the
__always_unused attribute from it.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent version of cppcheck falsely reports-
Variable ip.hdr is assigned a value that is never used.
ip is a union so the pointer ip.hdr is actually used when referenced as
ip.v4 and ip.v6. Silence these false reports when using cppcheck with the
--inline-suppr command-line option.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the driver has an uneven amount of Rx/Tx queues
setting the coalesce settings through ethtool will result in
an error. This is happening because in the setting coalesce
flow we are reporting an error if either Rx or Tx fails.
Also, the flow for setting/getting per_q_coalesce and
setting/getting coalesce settings for the entire device
is different.
Fix these issues by adding one function, ice_set_q_coalesce(),
and another, ice_get_q_coalesce(), that both getting/setting
per_q and entire device coalesce can use. This makes handling
the error cases generic between the two flows and simplifies
__ice_set_coalesce() and __ice_get_coalesce().
Also, add a header comment to __ice_set_coalesce().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when probing/removing the driver we allocate/deallocate
each vsi->q_vectors array in ice_vsi_alloc_arrays() and
ice_vsi_free_arrays() respectively. However, we don't do this
during the reset and VSI rebuild flow. This is inconsistent
and unnecessary to have a difference between the two flows.
This patch makes the change to always allocate/deallocate the
vsi->q_vectors array regardless of the driver flow we are in.
Also, update the comment for ice_vsi_free_arrays() to be more
descriptive.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The local variable speed does not need to be initialized and can cause some
static analysis tools to complain the initial assigned value is never used.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add few checks to validate msg from iavf driver.
Test if we have got enough q_vectors allocated in VSI connected with VF.
Add masks for itr_indx and msix_indx to avoid writing to reserved fieldi
of QINT. Clear q_vector->num_ring_rx/tx, without it we can increment this
value every time we send irq map msg from VF. So after second call this
value will be incorrect.
Decrement num_vectors from msg, because last vector in iavf msg is misc
vector (we don't set map for it).
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case of non-trusted VFs, it is possible to program VLAN filter far
less than what is requested by the VF originally, thereby makes number of
VLAN elements being tracked by VF different from actual VLAN tags. This
patch makes sure that we are not attempting to remove VLAN filter that
does not exist.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When Tx insertion is set, we are not accounting for the state of Rx
stripping. This causes Rx stripping to be enabled any time Tx
insertion is changed, even when it's supposed to be disabled.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disable VF if any malicious device driver (MDD) event is detected by
hardware. Track vf->num_mdd_events for information about VF MDD events.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many times in our functions we have a local variable pf, which is
equivalent to vsi->back. Just use pf consistently instead of vsi->back
where available.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For all other error cases in queue_userspace_packet() the error is
returned, so it makes sense to do the same for these two error cases.
Reported-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Acked-by: Flavio Leitner <fbl@sysclose.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_write_exgmac_batch is used in only one place, so we can remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek says:
====================
netlink: strict attribute checking follow-up
Three follow-up patches for recent strict netlink validation series.
Patch 1 fixes dump handling for genetlink families which validate and parse
messages themselves (e.g. because they need different policies for diferent
commands).
Patch 2 sets bad_attr in extack in one place where this was omitted.
Patch 3 adds new NL_VALIDATE_NESTED flags for strict validation to enable
checking that NLA_F_NESTED value in received messages matches expectations
and includes this flag in NL_VALIDATE_STRICT. This would change userspace
visible behavior but the previous switching to NL_VALIDATE_STRICT for new
code is still only in net-next at the moment.
v2: change error messages to mention NLA_F_NESTED explicitly
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new validation flag NL_VALIDATE_NESTED which adds three consistency
checks of NLA_F_NESTED_FLAG:
- the flag is set on attributes with NLA_NESTED{,_ARRAY} policy
- the flag is not set on attributes with other policies except NLA_UNSPEC
- the flag is set on attribute passed to nla_parse_nested()
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
v2: change error messages to mention NLA_F_NESTED explicitly
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check that attribute type is within 0...maxtype range in
__nla_validate_parse() sets only error message but not bad_attr in extack.
Set also bad_attr to tell userspace which attribute failed validation.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike do requests, dump genetlink requests now perform strict validation
by default even if the genetlink family does not set policy and maxtype
because it does validation and parsing on its own (e.g. because it wants to
allow different message format for different commands). While the null
policy will be ignored, maxtype (which would be zero) is still checked so
that any attribute will fail validation.
The solution is to only call __nla_validate() from genl_family_rcv_msg()
if family->maxtype is set.
Fixes: ef6243acb4 ("genetlink: optionally validate strictly/dumps")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Firmware version update
This patchset updates mlxsw to use a new firmware version and adds
support for split into two ports on Spectrum-2 based systems.
Patch #1 updates the firmware version to 13.2000.1122
Patch #2 queries new resources from the firmware.
Patch #3 makes use of these resources in order to support split into two
ports on Spectrum-2 based systems. The need for these resources is
explained by Shalom:
When splitting a port, different local ports need to be mapped on different
systems. For example:
SN3700 (local_ports_in_2x=2):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 5
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 3
front panel 2 --> local port 5
SN3800 (local_ports_in_2x=1):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 3
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 2
front panel 2 --> local port 3
The local_ports_in_{1x, 2x} resources provide the offsets from the base
local ports according to which the new local ports can be calculated.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting a port, different local ports need to be mapped on different
systems. For example:
SN3700 (local_ports_in_2x=2):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 5
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 3
front panel 2 --> local port 5
SN3800 (local_ports_in_2x=1):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 3
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 2
front panel 2 --> local port 3
The local_ports_in_{1x, 2x} resources provide the offsets from the base
local ports according to which the new local ports can be calculated.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the number of local ports in 4x changed between SPC and SPC-2,
firmware expose new resources that the driver can query.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new version supports two features that are required by upcoming
changes in the driver:
* Querying of new resources allowing port split into two ports on
Spectrum-2 systems
* Querying of number of gearboxes on supported systems such as SN3800
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC link can temporarily fall into "half-establish" that only one of
the link endpoints is ESTABLISHED and starts to send traffic, PROTOCOL
messages, whereas the other link endpoint is not up (e.g. immediately
when the endpoint receives ACTIVATE_MSG, the network interface goes
down...).
This is a normal situation and will be settled because the link
endpoint will be eventually brought down after the link tolerance time.
However, the situation will become worse when the second link is
established before the first link endpoint goes down,
For example:
1. Both links <1A-2A>, <1B-2B> down
2. Link endpoint 2A up, but 1A still down (e.g. due to network
disturbance, wrong session, etc.)
3. Link <1B-2B> up
4. Link endpoint 2A down (e.g. due to link tolerance timeout)
5. Node B starts failover onto link <1B-2B>
==> Node A does never start link failover.
When the "half-failover" situation happens, two consequences have been
observed:
a) Peer link/node gets stuck in FAILINGOVER state;
b) Traffic or user messages that peer node is trying to failover onto
the second link can be partially or completely dropped by this node.
The consequence a) was actually solved by commit c140eb166d ("tipc:
fix failover problem"), but that commit didn't cover the b). It's due
to the fact that the tunnel link endpoint has never been prepared for a
failover, so the 'l->drop_point' (and the other data...) is not set
correctly. When a TUNNEL_MSG from peer node arrives on the link,
depending on the inner message's seqno and the current 'l->drop_point'
value, the message can be dropped (- treated as a duplicate message) or
processed.
At this early stage, the traffic messages from peer are likely to be
NAME_DISTRIBUTORs, this means some name table entries will be missed on
the node forever!
The commit resolves the issue by starting the FAILOVER process on this
node as well. Another benefit from this solution is that we ensure the
link will not be re-established until the failover ends.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got an interesting report [0] that after resuming from hibernation
the link has 100Mbps instead of 1Gbps. Reason is that another OS has
been used whilst Linux was hibernated. And this OS speeds down the link
due to WoL. Therefore, when resuming, we shouldn't expect that what
the PHY advertises is what it did when hibernating.
Easiest way to do this is removing state PHY_RESUMING. Instead always
go via PHY_UP that configures PHY advertisement.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202851
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
