bx50v3 boards can be powered off via GPIO, this patch specifies the GPIO to
be used with the gpio-poweroff driver.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the imx6ul-pico-hobbit schematics the Ethernet PHY reset GPIO
is GPIO1_28, so fix it accordingly.
Also adjust the reset duration to 1ms, because the KSZ8081 datasheet
requires 500μs.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt the
polarity of "reset-gpio" is assumed to be active-low unless a separate
property "reset-gpio-active-high" is available. So replace the inconsistent
polarity description to make the correct active-low reset behavior more
obvious.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6sx-sdb has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6ul-evk has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-sdb has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6qdl-sabresd has WDOG2_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Utilite Pro has a mmc card slot connected to the usdhc3
controller. There is no card detection until hardware revision 1.3.
Add support for it and signal the controller with the broken-cd
property that polling has to be used to detect a card.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The current ldo settings of the cm-fx6 do not allow 1.2GHz cpu
frequency. At this frequency the module behaves unstable.
But the imx6q fuse indicates that 1.2GHz operation is possible.
Hence, remove the 1.2GHz operation point in the device tree.
Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
[christopher.spinrath@rwth-aachen.de: enhance commit message, adjust
remaining operation points to match the ones in imx6q.dtsi and add
a comment in the device tree]
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6 SMP system has the same DMA memory coherency issue [1] with
pl310 L2 controller. With this shared override bit set, the customer
reports the DMA coherency issue is gone. Besides, I have tested
the performance using USB ethernet with/without this bit, it shows
no difference.
[1] http://patchwork.ozlabs.org/patch/469362/
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With the SION bit set a pin can be read as GPIO even though it's not muxed
as GPIO. This is useful at times. The downside however is that the signal
is not only routed to the GPIO IP but also all other IPs that can make use
of the pin. This resulted in more than one issue for me in the past. Things
like spi transfers that result in usb reenumeration or setting a GPIO to a
value that triggers an RTS irq for an UART.
This convinces me that the SION bit does more harm than good and so all
SION bits are removed that are not known to be needed.
Note that this has no influence on GPIOs under Linux as the gpio-mxc
driver just reports the level the pin is driven to for outputs and not
the level as seen on the pin.
If this commit introduces a regression for you, please report which SION
bit is essential for your setup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "dis_rxdet_inp3_quirk" boolean property to USB3 node. This property
is used to disable rx detection in P3 PHY mode.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PCI reset GPIO is active low, so represent it with the
GPIO_ACTIVE_LOW flag.
Even though the imx6 PCI driver will not take the polarity into account
in this case, it is better to provide a correct description in device-tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license. In particular, the Utilite Pro
devicetree file (which includes imx6q-cm-fx6.dts) is already dual
licensed under GPLv2/X11.
Hence, relicense imx6q-cm-fx6.dts under GPLv2/X11 dual license.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CompuLab Utilite Pro is a miniature fanless desktop pc based on
the i.MX6 Quad powered cm-fx6 module. It features two serial ports,
USB OTG, 4x USB, analog audio and S/PDIF, 2x Gb Ethernet, HDMI and
DVI ports, an on-board 32GB SSD, a mmc slot, and on-board wifi/bt.
Add initial support for it including USB, Ethernet (both ports), sata
and HDMI support.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cm-fx6 module has an on-board spi-flash chip for its firmware, an
eeprom (containing e.g. the mac address of the on-board Ethernet),
a sata port, a pcie controller, an USB hub, and an USB otg port.
Enable support for them. In addition, enable syscon poweroff support.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6q-cm-fx6 iomuxc container node is not required. Remove it.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This fixes the following dtc warning by removing the unnecessary unit:
Warning (unit_address_vs_reg): Node /matrix-keypad@0 has a unit name,
but no reg property
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This fixes the following dtc warning by removing the unnecessary unit:
Warning (unit_address_vs_reg): Node /onewire@0 has a unit name,
but no reg property
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the missing reg properties for the regulator nodes
in order to fix the dtc warnings.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the missing reg properties for the MXS GPIO banks
in order to fix the dtc warnings.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Auvidea H100 is a baseboard for the SolidRun MicroSOM.
Its primary feature is a Toshiba TC358743 HDMI to CSI decoder,
allowing the board to work as HDMI passthrough and framegrabber.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the DT property to all boards that have the hardware workaround
for erratum ERR006687 present. This allows the CPUidle driver to use
the deep idle states, even if the FEC is active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This node describes the DI1 port of IPU, fix the node name to reflect this.
There's currently no user of this node in mainline, so this change should
not break any supported platforms.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the LCD8000-43T display and for the backlight
controlled via PWM1.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As of commit 1006ed7e1b ("serial: imx: Use generic uart-has-rtscts
DT property"), the Freescale IMX UART driver recognizes the generic
"uart-has-rtscts" DT property, deprecating the vendor-specific
"fsl,uart-has-rtscts" DT property. Hence replace the latter by the
former in all DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As of commit 182cdcb8bb ("serial: mxs-auart: Use generic
uart-has-rtscts DT property"), the Freescale MXS AUART driver recognizes
the generic "uart-has-rtscts" DT property, deprecating the
vendor-specific "fsl,uart-has-rtscts" DT property. Hence replace the
latter by the former in all DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for this small MP3 player based on STMP3780 (rev.3).
Currently supported are both external microSD and internal SD-NAND
bridge, PWM and USB gadget.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for this small MP3 player based on STMP3780 (rev.4).
Currently supported is both external microSD and internal SD-NAND
bridge, PWM and USB gadget.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add pinmux configuration for SSP2 port in SD mode, both for
the 4-bit and 8-bit case.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This enables support for the CAN controller located in the FPGA.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable FPGA's IRQ controller. It is in charge of dispatching interrupts
generated by IPs in the FPGA. The SoC is notified that an interrupt
occurred through a GPIO.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add input mux for UART2 RX in DTE mode. This allows to use the pad
UART2_TX_DATA_ALT0 as UART2 RX. This particular input select seems
to be missing in current reference manuals (Rev. B), but when looking
at the tables and other UART input select registers (e.g. UART3) it
seems naturally that this input mux register also has a fourth pad
option for UART2_TX_DATA_ALT0. It has also been proven to be required
to use UART2 in DTE mode and the particular pads on the Colibri iMX7
platform.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass "fsl,sai-mclk-direction-output" to the sai2 node, so that the
SAI2_MCLK can be an output.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SAI alias entries, which makes it possibe for the SAI driver
to retrieve the port instance.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Building with W=1 option leads to several warnings like:
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-1p1@110 has a unit name, but no reg property
Fix them by removing the unneeded unit-addresses.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The self-test was updated to cover zero-length strings; the function
needs to be updated, too.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Fixes: fcfd2fbf22 ("fs/namei.c: Add hashlen_string() function")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original name was simply hash_string(), but that conflicted with a
function with that name in drivers/base/power/trace.c, and I decided
that calling it "hashlen_" was better anyway.
But you have to do it in two places.
[ This caused build errors for architectures that don't define
CONFIG_DCACHE_WORD_ACCESS - Linus ]
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: fcfd2fbf22 ("fs/namei.c: Add hashlen_string() function")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The HPFS filesystem used generic_show_options to produce string that is
displayed in /proc/mounts. However, there is a problem that the options
may disappear after remount. If we mount the filesystem with option1
and then remount it with option2, /proc/mounts should show both option1
and option2, however it only shows option2 because the whole option
string is replaced with replace_mount_options in hpfs_remount_fs.
To fix this bug, implement the hpfs_show_options function that prints
options that are currently selected.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c8f33d0bec ("affs: kstrdup() memory handling") checks if the
kstrdup function returns NULL due to out-of-memory condition.
However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL. In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists. The mount syscall then fails with
ENOMEM.
This patch fixes the bug. We fail with ENOMEM only if data is non-NULL.
The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).
Fixes: c8f33d0bec ("affs: kstrdup() memory handling")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ce657611ba ("hpfs: kstrdup() out of memory handling") checks if
the kstrdup function returns NULL due to out-of-memory condition.
However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL. In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists. The mount syscall then fails with
ENOMEM.
This patch fixes the bug. We fail with ENOMEM only if data is non-NULL.
The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).
Fixes: ce657611ba ("hpfs: kstrdup() out of memory handling")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various builds (such as i386:allmodconfig) fail with
fs/binfmt_aout.c:133:2: error: expected identifier or '(' before 'return'
fs/binfmt_aout.c:134:1: error: expected identifier or '(' before '}' token
[ Oops. My bad, I had stupidly thought that "allmodconfig" covered this
on x86-64 too, but it obviously doesn't. Egg on my face. - Linus ]
Fixes: 5d22fc25d4 ("mm: remove more IS_ERR_VALUE abuses")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull string hash improvements from George Spelvin:
"This series does several related things:
- Makes the dcache hash (fs/namei.c) useful for general kernel use.
(Thanks to Bruce for noticing the zero-length corner case)
- Converts the string hashes in <linux/sunrpc/svcauth.h> to use the
above.
- Avoids 64-bit multiplies in hash_64() on 32-bit platforms. Two
32-bit multiplies will do well enough.
- Rids the world of the bad hash multipliers in hash_32.
This finishes the job started in commit 689de1d6ca ("Minimal
fix-up of bad hashing behavior of hash_64()")
The vast majority of Linux architectures have hardware support for
32x32-bit multiply and so derive no benefit from "simplified"
multipliers.
The few processors that do not (68000, h8/300 and some models of
Microblaze) have arch-specific implementations added. Those
patches are last in the series.
- Overhauls the dcache hash mixing.
The patch in commit 0fed3ac866 ("namei: Improve hash mixing if
CONFIG_DCACHE_WORD_ACCESS") was an off-the-cuff suggestion.
Replaced with a much more careful design that's simultaneously
faster and better. (My own invention, as there was noting suitable
in the literature I could find. Comments welcome!)
- Modify the hash_name() loop to skip the initial HASH_MIX(). This
would let us salt the hash if we ever wanted to.
- Sort out partial_name_hash().
The hash function is declared as using a long state, even though
it's truncated to 32 bits at the end and the extra internal state
contributes nothing to the result. And some callers do odd things:
- fs/hfs/string.c only allocates 32 bits of state
- fs/hfsplus/unicode.c uses it to hash 16-bit unicode symbols not bytes
- Modify bytemask_from_count to handle inputs of 1..sizeof(long)
rather than 0..sizeof(long)-1. This would simplify users other
than full_name_hash"
Special thanks to Bruce Fields for testing and finding bugs in v1. (I
learned some humbling lessons about "obviously correct" code.)
On the arch-specific front, the m68k assembly has been tested in a
standalone test harness, I've been in contact with the Microblaze
maintainers who mostly don't care, as the hardware multiplier is never
omitted in real-world applications, and I haven't heard anything from
the H8/300 world"
* 'hash' of git://ftp.sciencehorizons.net/linux:
h8300: Add <asm/hash.h>
microblaze: Add <asm/hash.h>
m68k: Add <asm/hash.h>
<linux/hash.h>: Add support for architecture-specific functions
fs/namei.c: Improve dcache hash function
Eliminate bad hash multipliers from hash_32() and hash_64()
Change hash_64() return value to 32 bits
<linux/sunrpc/svcauth.h>: Define hash_str() in terms of hashlen_string()
fs/namei.c: Add hashlen_string() function
Pull out string hash to <linux/stringhash.h>
