Current driver version is able to handle only one bridge at time.
Configuring two bridges on two different ports would end up shorting this
bridges by HW. To reproduce it:
ip l a name br0 type bridge
ip l a name br1 type bridge
ip l s dev br0 up
ip l s dev br1 up
ip l s lan1 master br0
ip l s dev lan1 up
ip l s lan2 master br1
ip l s dev lan2 up
Ping on lan1 and get response on lan2, which should not happen.
This happened, because current driver version is storing one global "Port VLAN
Membership" and applying it to all ports which are members of any
bridge.
To solve this issue, we need to handle each port separately.
This patch is dropping the global port member storage and calculating
membership dynamically depending on STP state and bridge participation.
Note: STP support was broken before this patch and should be fixed
separately.
Fixes: c2e866911e ("net: dsa: microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
Fix broken PTP over IP on Ocelot switches
Changes in v2: added patch 5, added Richard's ack for the whole series
sans patch 5 which is new.
Po Liu reported recently that timestamping PTP over IPv4 is broken using
the felix driver on NXP LS1028A. This has been known for a while, of
course, since it has always been broken. The reason is because IP PTP
packets are currently treated as unknown IP multicast, which is not
flooded to the CPU port in the ocelot driver design, so packets don't
reach the ptp4l program.
The series solves the problem by installing packet traps per port when
the timestamping ioctl is called, depending on the RX filter selected
(L2, L4 or both).
====================
Link: https://lore.kernel.org/r/20211126172845.3149260-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver doesn't support RX timestamping for non-PTP packets, but it
declares that it does. Restrict the reported RX filters to PTP v2 over
L2 and over L4.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IEEE 1588 support was declared too soon for the Ocelot switch. Out of
reset, this switch does not apply any special treatment for PTP packets,
i.e. when an event message is received, the natural tendency is to
forward it by MAC DA/VLAN ID. This poses a problem when the ingress port
is under a bridge, since user space application stacks (written
primarily for endpoint ports, not switches) like ptp4l expect that PTP
messages are always received on AF_PACKET / AF_INET sockets (depending
on the PTP transport being used), and never being autonomously
forwarded. Any forwarding, if necessary (for example in Transparent
Clock mode) is handled in software by ptp4l. Having the hardware forward
these packets too will cause duplicates which will confuse endpoints
connected to these switches.
So PTP over L2 barely works, in the sense that PTP packets reach the CPU
port, but they reach it via flooding, and therefore reach lots of other
unwanted destinations too. But PTP over IPv4/IPv6 does not work at all.
This is because the Ocelot switch have a separate destination port mask
for unknown IP multicast (which PTP over IP is) flooding compared to
unknown non-IP multicast (which PTP over L2 is) flooding. Specifically,
the driver allows the CPU port to be in the PGID_MC port group, but not
in PGID_MCIPV4 and PGID_MCIPV6. There are several presentations from
Allan Nielsen which explain that the embedded MIPS CPU on Ocelot
switches is not very powerful at all, so every penny they could save by
not allowing flooding to the CPU port module matters. Unknown IP
multicast did not make it.
The de facto consensus is that when a switch is PTP-aware and an
application stack for PTP is running, switches should have some sort of
trapping mechanism for PTP packets, to extract them from the hardware
data path. This avoids both problems:
(a) PTP packets are no longer flooded to unwanted destinations
(b) PTP over IP packets are no longer denied from reaching the CPU since
they arrive there via a trap and not via flooding
It is not the first time when this change is attempted. Last time, the
feedback from Allan Nielsen and Andrew Lunn was that the traps should
not be installed by default, and that PTP-unaware switching may be
desired for some use cases:
https://patchwork.ozlabs.org/project/netdev/patch/20190813025214.18601-5-yangbo.lu@nxp.com/
To address that feedback, the present patch adds the necessary packet
traps according to the RX filter configuration transmitted by user space
through the SIOCSHWTSTAMP ioctl. Trapping is done via VCAP IS2, where we
keep 5 filters, which are amended each time RX timestamping is enabled
or disabled on a port:
- 1 for PTP over L2
- 2 for PTP over IPv4 (UDP ports 319 and 320)
- 2 for PTP over IPv6 (UDP ports 319 and 320)
The cookie by which these filters (invisible to tc) are identified is
strategically chosen such that it does not collide with the filters used
for the ocelot-8021q tagging protocol by the Felix driver, or with the
MRP traps set up by the Ocelot library.
Other alternatives were considered, like patching user space to do
something, but there are so many ways in which PTP packets could be made
to reach the CPU, generically speaking, that "do what?" is a very valid
question. The ptp4l program from the linuxptp stack already attempts to
do something: it calls setsockopt(IP_ADD_MEMBERSHIP) (and
PACKET_ADD_MEMBERSHIP, respectively) which translates in both cases into
a dev_mc_add() on the interface, in the kernel:
https://github.com/richardcochran/linuxptp/blob/v3.1.1/udp.c#L73https://github.com/richardcochran/linuxptp/blob/v3.1.1/raw.c
Reality shows that this is not sufficient in case the interface belongs
to a switchdev driver, as dev_mc_add() does not show the intention to
trap a packet to the CPU, but rather the intention to not drop it (it is
strictly for RX filtering, same as promiscuous does not mean to send all
traffic to the CPU, but to not drop traffic with unknown MAC DA). This
topic is a can of worms in itself, and it would be great if user space
could just stay out of it.
On the other hand, setting up PTP traps privately within the driver is
not new by any stretch of the imagination:
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c#L833https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/dsa/hirschmann/hellcreek.c#L1050https://elixir.bootlin.com/linux/v5.16-rc2/source/include/linux/dsa/sja1105.h#L21
So this is the approach taken here as well. The difference here being
that we prepare and destroy the traps per port, dynamically at runtime,
as opposed to driver init time, because apparently, PTP-unaware
forwarding is a use case.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Reported-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As opposed to event messages (Sync, PdelayReq etc) which require
timestamping, general messages (Announce, FollowUp etc) do not.
In PTP they are part of different streams of data.
IEEE 1588-2008 Annex D.2 "UDP port numbers" states that the UDP
destination port assigned by IANA is 319 for event messages, and 320 for
general messages. Yet the kernel seems to be missing the definition for
general messages. This patch adds it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VCAP (Versatile Content Aware Processor) is the TCAM-based engine behind
tc flower offload on ocelot, among other things. The ingress port mask
on which VCAP rules match is present as a bit field in the actual key of
the rule. This means that it is possible for a rule to be shared among
multiple source ports. When the rule is added one by one on each desired
port, that the ingress port mask of the key must be edited and rewritten
to hardware.
But the API in ocelot_vcap.c does not allow for this. For one thing,
ocelot_vcap_filter_add() and ocelot_vcap_filter_del() are not symmetric,
because ocelot_vcap_filter_add() works with a preallocated and
prepopulated filter and programs it to hardware, and
ocelot_vcap_filter_del() does both the job of removing the specified
filter from hardware, as well as kfreeing it. That is to say, the only
option of editing a filter in place, which is to delete it, modify the
structure and add it back, does not work because it results in
use-after-free.
This patch introduces ocelot_vcap_filter_replace, which trivially
reprograms a VCAP entry to hardware, at the exact same index at which it
existed before, without modifying any list or allocating any memory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ocelot driver, when asked to timestamp all receiving packets, 1588
v1 or NTP, says "nah, here's 1588 v2 for you".
According to this discussion:
https://patchwork.kernel.org/project/netdevbpf/patch/20211104133204.19757-8-martin.kaistra@linutronix.de/#24577647
drivers that downgrade from a wider request to a narrower response (or
even a response where the intersection with the request is empty) are
buggy, and should return -ERANGE instead. This patch fixes that.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, HNS3 driver doesn't clear the reset flags of components after
successfully executing reset, it causes userspace info of
"Components reset" and "Components not reset" is incorrect.
So fix this problem by clear corresponding reset flag after reset process.
Fixes: ddccc5e368 ("net: hns3: add support for triggering reset by ethtool")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when user queries page pool info by debugfs command
"cat page_pool_info", the cnt of allocated page for page pool may be
incorrect because of memory inconsistency problem caused by compiler
optimization.
So this patch uses READ_ONCE() to read value of pages_state_hold_cnt to
fix this problem.
Fixes: 850bfb912a ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When page pool is not enabled, its address value is still NULL and page
pool should not be accessed, so add a check for it.
Fixes: 850bfb912a ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.
In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.
To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the variable 'p_bit->flags' is always 0,
the loop condition is always 0.
The variable 'j' may be greater than or equal to 32.
At this time, the array 'p_aeu->bits[32]' may be out
of bound.
Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Link: https://lore.kernel.org/r/20211125113610.273841-1-zhangyue1@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When applications call shutdown() with SHUT_RDWR in userspace,
smc_close_active() calls kernel_sock_shutdown(), and it is called
twice in smc_shutdown().
This fixes this by checking sk_state before do clcsock shutdown, and
avoids missing the application's call of smc_shutdown().
Link: https://lore.kernel.org/linux-s390/1f67548e-cbf6-0dce-82b5-10288a4583bd@linux.ibm.com/
Fixes: 606a63c978 ("net/smc: Ensure the active closing peer first closes clcsock")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126024134.45693-1-tonylu@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Inject error before dev_hold(real_dev) in register_vlan_dev(),
and execute the following testcase:
ip link add dev dummy1 type dummy
ip link add name dummy1.100 link dummy1 type vlan id 100
ip link del dev dummy1
When the dummy netdevice is removed, we will get a WARNING as following:
=======================================================================
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 2 PID: 0 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0
and an endless loop of:
=======================================================================
unregister_netdevice: waiting for dummy1 to become free. Usage count = -1073741824
That is because dev_put(real_dev) in vlan_dev_free() be called without
dev_hold(real_dev) in register_vlan_dev(). It makes the refcnt of real_dev
underflow.
Move the dev_hold(real_dev) to vlan_dev_init() which is the call-back of
ndo_init(). That makes dev_hold() and dev_put() for vlan's real_dev
symmetrical.
Fixes: 563bcbae3b ("net: vlan: fix a UAF in vlan_dev_real_dev()")
Reported-by: Petr Machata <petrm@nvidia.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20211126015942.2918542-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All the filter names are missing _PTP in them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20211126031921.2466944-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ethtool_set_coalesce() now uses both the .get_coalesce() and
.set_coalesce() callbacks. But the check for their availability is
buggy, so changing the coalesce settings on a device where the driver
provides only _one_ of the callbacks results in a NULL pointer
dereference instead of an -EOPNOTSUPP.
Fix the condition so that the availability of both callbacks is
ensured. This also matches the netlink code.
Note that reproducing this requires some effort - it only affects the
legacy ioctl path, and needs a specific combination of driver options:
- have .get_coalesce() and .coalesce_supported but no
.set_coalesce(), or
- have .set_coalesce() but no .get_coalesce(). Here eg. ethtool doesn't
cause the crash as it first attempts to call ethtool_get_coalesce()
and bails out on error.
Fixes: f3ccfda193 ("ethtool: extend coalesce setting uAPI with CQE mode")
Cc: Yufeng Mo <moyufeng@huawei.com>
Cc: Huazhong Tan <tanhuazhong@huawei.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126175543.28000-1-jwi@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Device permissions is S_IALLUGO, with many unnecessary bits. Remove them
and also remove read and write permissions from group and others.
Before the change:
crwsrwsrwt 1 0 0 10, 125 Nov 25 13:59 /dev/virtual_nci
After the change:
crw------- 1 0 0 10, 125 Nov 25 14:05 /dev/virtual_nci
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Link: https://lore.kernel.org/r/20211125141457.716921-1-cascardo@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Tx queues were not disabled in situations where the driver needed to
stop the interface to apply a new configuration. This could result in a
kernel panic when doing any of the 3 following actions:
* reconfiguring the number of queues (ethtool -L)
* reconfiguring the size of the ring buffers (ethtool -G)
* installing/removing an XDP program (ip l set dev ethX xdp)
Prevent the panic by making sure netif_tx_disable is called when stopping
an interface.
Without this patch, the following kernel panic can be observed when doing
any of the actions above:
Unable to handle kernel paging request at virtual address ffff80001238d040
[....]
Call trace:
dwmac4_set_addr+0x8/0x10
dev_hard_start_xmit+0xe4/0x1ac
sch_direct_xmit+0xe8/0x39c
__dev_queue_xmit+0x3ec/0xaf0
dev_queue_xmit+0x14/0x20
[...]
[ end trace 0000000000000002 ]---
Fixes: 5fabb01207 ("net: stmmac: Add initial XDP support")
Fixes: aa042f60e4 ("net: stmmac: Add support to Ethtool get/set ring parameters")
Fixes: 0366f7e06a ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20211124154731.1676949-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski says:
====================
tls: splice_read fixes
As I work my way to unlocked and zero-copy TLS Rx the obvious bugs
in the splice_read implementation get harder and harder to ignore.
This is to say the fixes here are discovered by code inspection,
I'm not aware of anyone actually using splice_read.
====================
Link: https://lore.kernel.org/r/20211124232557.2039757-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previous patch fixes overriding callbacks incorrectly. Triggering
the crash in sendpage_locked would be more spectacular but it's
hard to get to, so take the easier path of proving this is broken
and call getname. We're currently getting IPv4 socket info on an
IPv6 socket.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We replace proto_ops whenever TLS is configured for RX. But our
replacement also overrides sendpage_locked, which will crash
unless TX is also configured. Similarly we plug both of those
in for TLS_HW (NIC crypto offload) even tho TLS_HW has a completely
different implementation for TX.
Last but not least we always plug in something based on inet_stream_ops
even though a few of the callbacks differ for IPv6 (getname, release,
bind).
Use a callback building method similar to what we do for struct proto.
Fixes: c46234ebb4 ("tls: RX path for ktls")
Fixes: d4ffb02dee ("net/tls: enable sk_msg redirect to tls socket egress")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
recvmsg() will put peek()ed and partially read records onto the rx_list.
splice_read() needs to consult that list otherwise it may miss data.
Align with recvmsg() and also put partially-read records onto rx_list.
tls_sw_advance_skb() is pretty pointless now and will be removed in
net-next.
Fixes: 692d7b5d1f ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We don't support splicing control records. TLS 1.3 changes moved
the record type check into the decrypt if(). The skb may already
be decrypted and still be an alert.
Note that decrypt_skb_update() is idempotent and updates ctx->decrypted
so the if() is pointless.
Reorder the check for decryption errors with the content type check
while touching them. This part is not really a bug, because if
decryption failed in TLS 1.3 content type will be DATA, and for
TLS 1.2 it will be correct. Nevertheless its strange to touch output
before checking if the function has failed.
Fixes: fedf201e12 ("net: tls: Refactor control message handling on recv")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The issue happened randomly in runtime. The message "Link is Down" is
popped but soon it recovered to "Link is Up".
The "Link is Down" results from the incorrect read data for reading the
PHY register via MDIO bus. The correct sequence for reading the data
shall be:
1. fire the command
2. wait for command done (this step was missing)
3. wait for data idle
4. read data from data register
Cc: stable@vger.kernel.org
Fixes: f160e99462 ("net: phy: Add mdio-aspeed")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211125024432.15809-1-dylan_hung@aspeedtech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.
Danielle brought this back up as still occurring, so we'll try
again.
[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0
As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.
Fixes: 16eb8815c2 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Karsten Graul says:
====================
net/smc: fixes 2021-11-24
Patch 1 from DaXing fixes a possible loop in smc_listen().
Patch 2 prevents a NULL pointer dereferencing while iterating
over the lower network devices.
====================
Link: https://lore.kernel.org/r/20211124123238.471429-1-kgraul@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The kernel_listen function in smc_listen will fail when all the available
ports are occupied. At this point smc->clcsock->sk->sk_data_ready has
been changed to smc_clcsock_data_ready. When we call smc_listen again,
now both smc->clcsock->sk->sk_data_ready and smc->clcsk_data_ready point
to the smc_clcsock_data_ready function.
The smc_clcsock_data_ready() function calls lsmc->clcsk_data_ready which
now points to itself resulting in an infinite loop.
This patch restores smc->clcsock->sk->sk_data_ready with the old value.
Fixes: a60a2b1e0a ("net/smc: reduce active tcp_listen workers")
Signed-off-by: Guo DaXing <guodaxing@huawei.com>
Acked-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Coverity reports a possible NULL dereferencing problem:
in smc_vlan_by_tcpsk():
6. returned_null: netdev_lower_get_next returns NULL (checked 29 out of 30 times).
7. var_assigned: Assigning: ndev = NULL return value from netdev_lower_get_next.
1623 ndev = (struct net_device *)netdev_lower_get_next(ndev, &lower);
CID 1468509 (#1 of 1): Dereference null return value (NULL_RETURNS)
8. dereference: Dereferencing a pointer that might be NULL ndev when calling is_vlan_dev.
1624 if (is_vlan_dev(ndev)) {
Remove the manual implementation and use netdev_walk_all_lower_dev() to
iterate over the lower devices. While on it remove an obsolete function
parameter comment.
Fixes: cb9d43f677 ("net/smc: determine vlan_id of stacked net_device")
Suggested-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marek Behún says:
====================
phylink resolve fixes
With information from me and my nagging, Russell has produced two fixes
for phylink, which add code that triggers another phylink_resolve() from
phylink_resolve(), if certain conditions are met:
interface is being changed
or
link is down and previous link was up
These are needed because sometimes the PCS callbacks may provide stale
values if link / speed / ...
====================
Link: https://lore.kernel.org/r/20211123154403.32051-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following
description:
This register bit indicates when link was lost since the last
read. For the current link status, read this register
back-to-back.
Thus to get current link state, we need to read the register twice.
But doing that in the link change interrupt handler would lead to
potentially ignoring link down events, which we really want to avoid.
Thus this needs to be solved in phylink's resolve, by retriggering
another resolve in the event when PCS reports link down and previous
link was up, and by re-reading PCS state if the previous link was down.
The wrong value is read when phylink requests change from sgmii to
2500base-x mode, and link won't come up. This fixes the bug.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On PHY state change the phylink_resolve() function can read stale
information from the MAC and report incorrect link speed and duplex to
the kernel message log.
Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell
88E6393X switch:
- PHY driver triggers state change due to PHY interface mode being
changed from 10gbase-r to 2500base-x due to copper change in speed
from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed
its interface to the host, or the interrupt about loss of SerDes link
hadn't arrived yet (there can be a delay of several milliseconds for
this), so we still think that the 10gbase-r mode is up
- phylink_resolve()
- phylink_mac_pcs_get_state()
- this fills in speed=10g link=up
- interface mode is updated to 2500base-x but speed is left at 10Gbps
- phylink_major_config()
- interface is changed to 2500base-x
- phylink_link_up()
- mv88e6xxx_mac_link_up()
- .port_set_speed_duplex()
- speed is set to 10Gbps
- reports "Link is Up - 10Gbps/Full" to dmesg
Afterwards when the interrupt finally arrives for mv88e6xxx, another
resolve is forced in which we get the correct speed from
phylink_mac_pcs_get_state(), but since the interface is not being
changed anymore, we don't call phylink_major_config() but only
phylink_mac_config(), which does not set speed/duplex anymore.
To fix this, we need to force the link down and trigger another resolve
on PHY interface change event.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Usage of phy_ethtool_get_link_ksettings() in the link status change
handler isn't needed, and in combination with the referenced change
it results in a deadlock. Simply remove the call and replace it with
direct access to phydev->speed. The duplex argument of
lan743x_phy_update_flowcontrol() isn't used and can be removed.
Fixes: c10a485c3d ("phy: phy_ethtool_ksettings_get: Lock the phy for consistency")
Reported-by: Alessandro B Maurici <abmaurici@gmail.com>
Tested-by: Alessandro B Maurici <abmaurici@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/40e27f76-0ba3-dcef-ee32-a78b9df38b0f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While testing BIG TCP patch series, I was expecting that TCP_RR workloads
with 80KB requests/answers would send one 80KB TSO packet,
then being received as a single GRO packet.
It turns out this was not happening, and the root cause was that
cubic Hystart ACK train was triggering after a few (2 or 3) rounds of RPC.
Hystart was wrongly setting CWND/SSTHRESH to 30, while my RPC
needed a budget of ~20 segments.
Ideally these TCP_RR flows should not exit slow start.
Cubic Hystart should reset itself at each round, instead of assuming
every TCP flow is a bulk one.
Note that even after this patch, Hystart can still trigger, depending
on scheduling artifacts, but at a higher CWND/SSTHRESH threshold,
keeping optimal TSO packet sizes.
Tested:
ip link set dev eth0 gro_ipv6_max_size 131072 gso_ipv6_max_size 131072
nstat -n; netperf -H ... -t TCP_RR -l 5 -- -r 80000,80000 -K cubic; nstat|egrep "Ip6InReceives|Hystart|Ip6OutRequests"
Before:
8605
Ip6InReceives 87541 0.0
Ip6OutRequests 129496 0.0
TcpExtTCPHystartTrainDetect 1 0.0
TcpExtTCPHystartTrainCwnd 30 0.0
After:
8760
Ip6InReceives 88514 0.0
Ip6OutRequests 87975 0.0
Fixes: ae27e98a51 ("[TCP] CUBIC v2.3")
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20211123202535.1843771-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the B53 Ethernet switch section to contain
drivers/net/dsa/bcm_sf2*.
Reported-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211123222422.3745485-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2021-11-24
A fix from Alexander which has been brought up various times found by
automated checkers. Make sure values are in u32 range.
* tag 'ieee802154-for-net-2021-11-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
net: ieee802154: handle iftypes as u32
====================
Link: https://lore.kernel.org/r/20211124150934.3670248-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update NC-SI command handler (both standard and OEM) to take into
account of payload paddings in allocating skb (in case of payload
size is not 32-bit aligned).
The checksum field follows payload field, without taking payload
padding into account can cause checksum being truncated, leading to
dropped packets.
Fixes: fb4ee67529 ("net/ncsi: Add NCSI OEM command support")
Signed-off-by: Kumar Thangavel <thangavel.k@hcl.com>
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mvpp2_xdp_setup won't allow attaching XDP program if
mtu > ETH_DATA_LEN (1500).
The mvpp2_change_mtu on the other hand checks whether
MVPP2_RX_PKT_SIZE(mtu) > MVPP2_BM_LONG_PKT_SIZE.
These two checks are semantically different.
Moreover this limit can be increased to MVPP2_MAX_RX_BUF_SIZE, since in
mvpp2_rx we have
xdp.data = data + MVPP2_MH_SIZE + MVPP2_SKB_HEADROOM;
xdp.frame_sz = PAGE_SIZE;
Change the checks to check whether
mtu > MVPP2_MAX_RX_BUF_SIZE
Fixes: 07dd0a7aae ("mvpp2: add basic XDP support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling ipa_cmd_pipeline_clear() after stopping the channel
underlying the AP<-modem RX endpoint can lead to a deadlock.
This occurs in the ->runtime_suspend device power operation for the
IPA driver. While this callback is in progress, any other requests
for power will block until the callback returns.
Stopping the AP<-modem RX channel does not prevent the modem from
sending another packet to this endpoint. If a packet arrives for an
RX channel when the channel is stopped, an SUSPEND IPA interrupt
condition will be pending. Handling an IPA interrupt requires
power, so ipa_isr_thread() calls pm_runtime_get_sync() first thing.
The problem occurs because a "pipeline clear" command will not
complete while such a SUSPEND interrupt condition exists. So the
SUSPEND IPA interrupt handler won't proceed until it gets power;
that won't happen until the ->runtime_suspend callback (and its
"pipeline clear" command) completes; and that can't happen while
the SUSPEND interrupt condition exists.
It turns out that in this case there is no need to use the "pipeline
clear" command. There are scenarios in which clearing the pipeline
is required while suspending, but those are not (yet) supported
upstream. So a simple fix, avoiding the potential deadlock, is to
stop calling ipa_cmd_pipeline_clear() in ipa_endpoint_suspend().
This removes the only user of ipa_cmd_pipeline_clear(), so get rid
of that function. It can be restored again whenever it's needed.
This is basically a manual revert along with an explanation for
commit 6cb63ea6a3 ("net: ipa: introduce ipa_cmd_tag_process()").
Fixes: 6cb63ea6a3 ("net: ipa: introduce ipa_cmd_tag_process()")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the process of driver probing, probe function should return < 0
for failure, otherwise kernel will treat value == 0 as success.
Therefore, we should set err to -EINVAL when
adapter->registered_device_map is NULL. Otherwise kernel will assume
that driver has been successfully probed and will cause unexpected
errors.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
