Move mt76x02_dma_init, mt76x02_init_rx_queue and mt76x02_init_tx_queue
routines in mt76x02-lib module in order to be reused by mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_set_irq_mask, mt76x02_irq_enable and mt76x02_irq_disable
in mt76x02-lib module in order to be reused by mt76x0 driver.
Moreover move irq_lock and irqmask in mt76_mmio data structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76x02_dma_enable and mt76x02_dma_disable utility routines
in order to be reused in mt76x0 mac configuration and remove duplicated
code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move wait_for_wpdma utility routine in mt76x02_dma.h
in order to be reused by mt76x0 driver. Moreover add
the possibility to specify the timeout value in
wait_for_wpdma signature
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76_poll utility routine in mt76x0_set_wlan_state to check
if the PLL/XTAL is ready
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If the WLAN core is still active during initialization, it might cause
the MCU or DMA to hang. This can happen during soft reboot, so disable
the core + clock early to avoid this issue.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
TP-LINK Archer T1U do not support 2.4GHz band despite EEPROM
reports that. Add quirk to mask out 2.4GHz support.
Reported-by: Sid Hayn <sidhayn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76 uses __skb_pad() with free_on_error set to true, this is the same
as calling skb_pad().
This patch does not change any functionality, but it makes it easier to
backport this driver in backports, because skb_pad() is also available
in older kernel versions.
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
print fw_ver and build_ver members of struct mt76x02_fw_header, similarly
to what appears in the output of 'dmesg' when the MCU firmware is loaded.
Reported-by: Sid Hayn <sidhayn@gmail.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0_phy_set_txpower routine in order to configure
base and per rate tx power gain. Moreover take into account
txpower_conf in order to limit the tx power gain according to
the bound provided by mac80211
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76 shared debugfs implementation and remove duplicated code
in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to unify eeprom parsing between mt76x0 and mt76x2 drivers,
remove eeprom pointer dependency from mt76x0_get_power_info routine.
Remove mt76x0_eeprom_params since it is now an empty structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to unify eeprom parsing between mt76x0 and mt76x2 drivers,
remove eeprom pointer dependency from mt76x0_set_tx_power_per_rate.
Moreover use mt76_rate_power to store power vs rate calibration data.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x0_extra_power_over_mac and mt76x0_phy_set_tx_power routines
since they are not actually used and tx power handling will be unified
with mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_rate_power_val and mt76x2_sign_extend_optional utility
routines in mt76x02_eeprom.h in order to reuse them in mt76x0 eeprom
parsing
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move rate_txpower handler in mt76 debugfs in order to be reused
in mt76x0 driver and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x02_phy_set_txpower utility routine in mt76x02_phy.c
in order to be reused in mt76x0 tx power management code.
Moreover move following routines in mt76x02-lib module:
- mt76x02_tx_power_mask
- mt76x02_get_max_rate_power
- mt76x02_limit_rate_power
- mt76x02_add_rate_power_offset
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_rate_power data structure from mt76x2_dev to mt76_dev in order
to share it with mt76x0 driver. Moreover move txpower_conf and
txpower_cur in mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We need to return bool value in mt76x02_wait_for_mac.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 2735a6dd7d ("mt76: unify wait_for_mac")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove not useful WARN_ON macros in mt76u_get_rx_entry_len routine
since corrupted frames should just be silently discarded
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_tssi_enabled and mt76x02_temp_tx_alc_enabled in
mt76x02_eeprom.h in order to be reused in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify parse hw capabilities with mt76x2 driver using
mt76x02_eeprom_parse_hw_cap utility routine available
in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_eeprom_parse_hw_cap utility routine in mt76x02-lib
module in order to be reused in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify frequency offset parsing with mt76x2 driver using
eeprom utility routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify temperature offset parsing with mt76x2 driver using
eeprom utility routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify rssi_offset parsing with mt76x2 driver using eeprom utility
routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify lna gain parsing with mt76x2 driver using eeprom utility
routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x02_get_rx_gain and mt76x02_get_lna_gain utility routines
for rx gain parsing. mt76x02_get_rx_gain and mt76x02_get_lna_gain
will be reused for eeprom parsing in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x0_set_country_reg routine for the moment
since it is partial and it is not actually used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_ext_pa_enabled utility routine in mt76x02_eeprom.c
and remove duplicated code. This is a preliminary patch to
unify eeprom code between mt76x2 and mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_efuse_read and mt76x2_get_efuse_data in mt76x02_eeprom.c
in order to be reused in mt76x0 driver for eeprom parsing
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_mac_setaddr utility routine in mt76x02-lib
module and remove duplicated code. This is a preliminary patch
to unify eeprom code between mt76x2 and mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_eeprom_get utility routine in mt76x02_eeprom.h since
it will be used to parse mt76x0 eeprom in order to unify eeprom
support between mt76x2 and mt76x0 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move shared eeprom utility routines in mt76x02_eeprom.h and
remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2 and mt76x0 common definitions in mt76x02_eeprom.h
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add stbc tx power eeprom parsing support for mt76x2 driver.
When writing power entries, make a distinction between rates that are
read from the same EEPROM value, but have separate register entries.
No effect on runtime behavior, but preparation for unification with mt76x0
and for placing restrictions on individual rate power limits
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move seq_put_array utility routine in mt76-core module
in order to be reused in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7650 PCI id found on ASUS rt-51ac to pci_device_id table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix tx power configuration for VHT 1SS/STBC mcs 9 since
in MT_TX_PWR_CFG_{8,9} mcs 8,9 bits are GENMASK(21,16) and
GENMASK(29,24) while GENMASK(15,6) are marked as reserved
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/quantenna/qtnfmac/cfg80211.c: In function 'qtnf_dump_survey':
drivers/net/wireless/quantenna/qtnfmac/cfg80211.c:694:19: warning:
variable 'vif' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ucode chunk might be relatively large and the allocation with
kmalloc() may fail occasionally. Since the data isn't DMA-transferred
but by manual loops, we can use vmalloc instead of kmalloc.
For a better performance, though, kvmalloc() would be the best choice
in such a case, so let's replace with it.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1103431
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_rxglom':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1466:11: warning:
variable 'sfdoff' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_bus_preinit':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:3408:7: warning:
variable 'pad_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
debugfs_remove_recursive has taken IS_ERR_OR_NULL into account. So just
remove the condition check before debugfs_remove_recursive.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When obtaining the firmware capability a buffer is provided of 512
bytes. However, if all features in firmware are supported the buffer
needs to be 565 bytes as otherwise truncated information is retrieved
from firmware. Increasing the buffer to 768 bytes on stack.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove mt76_fw dependency from mt76x0u_upload_firmware routine since
it does not define firmware layout properly. Moreover use mt76_poll_msec
utility routine to check if the fw is properly running
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
