Commit Graph

588523 Commits

Author SHA1 Message Date
Fabio Estevam
b26a68c1fb ARM: dts: imx6: Do not hardcode the CLKO clock
Using "IMX6QDL_CLK_CKO" for the clock is easier to read instead of
the hardcoded clock number.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-27 10:55:50 +08:00
Sergio Prado
b18f909376 ARM: dts: imx6: Add dts for Embest MarS Board
Embest MarS Board [1] is a multi-core platform based on Freescale i.MX6
Cortex-A9 Dual Core, running up to 1GHz with 1 GB of RAM, 4GB of eMMC
and with a 4MB SPI flash.

[1] http://www.embest-tech.com/shop/star/marsboard.html

Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-27 10:54:11 +08:00
Joshua Clayton
416196cd90 ARM: dts: imx6: fix dtc warnings for ipu endpoints
When compiled with "W=1", dtc complains: e.g.
"Warning (unit_address_vs_reg):
Node /soc/ipu@02800000/port@2/endpoint@0
has a unit name, but no reg property"

Endpoint nodes don't have a reg property, and the addresses
in their node names are ordinals without any special meaning
so remove them and swap them for semantic node names.

Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-26 19:52:23 +08:00
Fabio Estevam
46350b71a0 ARM: dts: imx6dl: Fix the VDD_ARM_CAP voltage for 396MHz operation
Table 8 from MX6DL datasheet (IMX6SDLCEC Rev. 5, 06/2015):
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6SDLCEC.pdf

states the following:

"LDO Output Set Point (VDD_ARM_CAP) = 1.125 V minimum for operation
up to 396 MHz."

So fix the entry by adding the 25mV margin value as done in the other
entries of the table, which results in 1.15V for 396MHz operation.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-26 19:52:20 +08:00
Fabio Estevam
fe4266baba ARM: dts: imx6sx: Add 198MHz operating point
198MHz is a valid operating point for mx6sx.

Add entries for VDD_ARM_CAP and VDD_SOC_CAP voltages for 198MHz according
to the imx6sx datahseet:
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6SXIEC.pdf

(a 25mV offset is added to the minimum allowed values for safety).

These values also match the ones from the NXP kernel.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-26 19:52:17 +08:00
Fabio Estevam
f70844460f ARM: dts: imx6ul: Fix operating points
Adjust the VDD_ARM_CAP and VDD_SOC_CAP voltages according to
Table-11 from MX6UL datasheet:
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6ULCEC.pdf

(a 25mV offset is added to the minimum allowed values for safety).

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-26 19:52:11 +08:00
Akshay Bhat
c0b20d6f41 ARM: dts: imx6q-ba16: use wdog external reset
The BA16 module has a PMIC that uses the WDOG_B output from iMX6 to
reset the system on a watchdog timeout. Configure the watchdog to assert
the external reset signal (WDOG_B) using fsl,ext-reset-output property.

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-26 11:22:23 +08:00
Akshay Bhat
15ef03b862 ARM: dts: imx: b450/b650v3: Move ldb_di clk assignment
Previously the LDB_DIx clocks could be specified in the ldb node. With
the ERR009219 errata fix applied, the ldb_di clocks now needs to be
specified in the clks node to ensure the clocks are setup early in the
boot process.

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-26 11:05:33 +08:00
Akshay Bhat
b492b8744d ARM: dts: imx6q-b850v3: Update display clock source
The default monitor that ships with B850v3 requires a 65MHz pixel clock.
65MHz can not be achieved using PLL3 (480MHz/7=68.5MHz). Hence set the
LDB_DIx clock source to PLL5. Since PLL5 is already in use by IPU1_DIx,
set the clock source for IPU1_DIx to PLL2_PFD2 to allow simultaneous
display on both LVDS and HDMI interface.

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-26 11:05:30 +08:00
Akshay Bhat
7532c98f3a ARM: dts: imx6q-b850v3: Remove ldb panel
Remove ldb panel entry for the following reasons:
- The b850v3 has an onboard LVDS to DisplayPort converter (STDP4028). So
we should not limit the monitors that can be connected by hardcoding the
auo,b133htn01 1080p panel.
- The default resolution on the LVDS interface needs to be WXGA or less.
Otherwise when a 1080p monitor is connected to the HDMI port there is no
output on both the LVDS and HDMI ports since a single IPU on i.MX6 can
not handle two 1080p displays. With the panel entry removed from the
devicetree, drm driver defaults the resolution on LVDS interface to XGA.

Once in userspace, applications can set the desired resolution on LVDS
interface over IPU2 CRTC.

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-26 11:05:24 +08:00
Maciej S. Szmigiero
880e1509db ARM: dts: imx6qdl-udoo: add 7 inch LCD touchscreen panel support
The official UDOO board kit has 7 and 15.6 inch touchscreen LCD panels
as options.

This patch adds support for 7 inch panel only, but the 15.6 inch one
should be easy to add using the same regulator, backlight device and
LVDS channel.

Since this panel is an option for UDOO board it is disabled by default
and can be enabled (for example) by the following U-Boot commands:
fdt set backlight status okay
fdt set panelchan status okay
fdt set panel7 status okay
fdt set touchscreenp7 status okay

The LVDS channels is also disabled by default to avoid warning from its
driver.

Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-18 12:54:21 +08:00
Alexander Kurz
d8c8c70c48 ARM: dts: i.MX3x: add keypad port devicetree nodes
Add the Keypad Port (KPP) devicetree nodes for IMX31 and IMX35 SOC.

Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-18 12:49:49 +08:00
Stefan Agner
5d01e99ebf ARM: dts: ls1021a: add pix clock to DCU dts node
The DCU IP has distinct clock inputs for register access and the
pixel clocks, at least in some implementations. LS1021a seems to
use the same clock, therefore specify the same clock for "dcu"
and "pix".

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:48:04 +08:00
Alexander Stein
5b9f967c07 ARM: dts: ls1021a: DSPI has 6 chip-selects
Both DSPI have signals SPIn_PCS[0:5] so in summary 6 chip-selects, not 5.
Fix that.

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:48:03 +08:00
Liu Gang
c54dd442b4 ARM: dts: ls1021a: Add gpio support for ls1021a platform
Add gpio nodes for ls1021a platform dts file. The gpio
IP block of the ls1021a can be supported by the code
drivers/gpio/gpio-mpc8xxx.c.

The compatible "fsl,qoriq-gpio" is used by gpio driver:
drivers/gpio/gpio-mpc8xxx.c to implement general gpio
functionalities.

The chip-specific compatible "fsl,ls1021a-gpio" may be
used to fix potential gpio IP block errata or other
chip-specific gpio issues.

Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:48:03 +08:00
Akshay Bhat
027309fc85 ARM: dts: imx6q-ba16: Remove unused vqmmc-supply
The vqmmc supply is not connected to bio supply on the BA16 module.
Hence remove vqmmc-supply property in usdhc3 node.

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:48:02 +08:00
Minghuan Lian
f4a458fd83 ARM: dts: ls1021a: add SCFG MSI dts node
Add SCFG MSI dts node and add msi-parent property to PCIe dts node
that points to the corresponding MSI node.

Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:48:02 +08:00
Uwe Kleine-König
9eb7db1c35 ARM: dts: imx28: add alternative pinmuxing for mac0
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:48:01 +08:00
Soeren Moch
cc1fb3e1f2 ARM: dts: imx6q-tbs2910: fix fec reset polarity
According to Documentation/devicetree/bindings/net/fsl-fec.txt the polarity
of "phy-reset-gpios" is assumed to be active-low unless a separate property
"phy-reset-active-high" is available. So replace the inconsistent polarity
description to make the correct active-low reset behavior more obvious.

Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:48:01 +08:00
Cory Tusar
1556063fde ARM: dts: vf610-zii-dev: Add ZII development board.
This commit adds support for Rev. B of a Zodiac Inflight Innovations
development board, mainly intended for DSA and ARINC 429 development
work.

Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:48:00 +08:00
Stefan Agner
ef4a4e14ce ARM: dts: vfxxx: add missing reg properties
Add missing reg properties to AIPS bus and Cortex-A5's PMU unit.
This change avoids the following warnings:
 Warning (unit_address_vs_reg): Node /soc/aips-bus@40000000 has a unit
 name, but no reg property
 Warning (unit_address_vs_reg): Node /soc/aips-bus@40080000 has a unit
 name, but no reg property
 Warning (unit_address_vs_reg): Node /soc/aips-bus@40080000/pmu@40089000
 has a unit name, but no reg property

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:48:00 +08:00
Stefan Agner
6d20b24a2b ARM: dts: vf-colibri: increase NAND clock speed
The NAND flash memory populated on Colibri VF61 allows faster NAND
timings than the flash memory on VF50. Additionally, due to divider
limitations, VF61 did clock the flash even slower than VF50. Assign
the NFC clock in the module specific device trees vf500-colibri.dtsi
and vf610-colibri.dtsi respectively.

This increases raw read speed on Colibri VF61 by about 20%.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:59 +08:00
Stefan Agner
9b1a1779e9 ARM: dts: vf-colibri: alias the primary FEC as ethernet0
The Vybrid based Colibri modules provide a on-module PHY which is
connected to the second FEC instance FEC1. Since the on-module
Ethernet port is considered as primary ethernet interface, alias
fec1 as ethernet0. This also makes sure that the first MAC address
provided by the boot loader gets assigned to the FEC instance used
for the on-module PHY.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:59 +08:00
Fabio Estevam
29e88b6de0 ARM: dts: imx6sx-sdb: Add SAI support
Introduce imx6sx-sdb-sai.dts so that it is possible to use the
SAI interface.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:58 +08:00
Fabio Estevam
3883dd74f0 bindings: fsl-imx-sdma: Document 'fsl,sdma-event-remap' property
Document the 'fsl,sdma-event-remap' property and provide an example of
its usage.

Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:58 +08:00
Fabio Estevam
88b53b9c1f ARM: dts: imx6sx: Remove unused property
Property 'dma-source' is not used anywhere, nor it is documented, so
let's just get rid of it.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:57 +08:00
Fabio Estevam
78f31b0b01 ARM: dts: imx6sx: Fix SAI DMA index
According to sdma_peripheral_type in include/linux/platform_data/dma-imx.h
IMX_DMATYPE_SAI corresponds to index 24, so fix it accordingly.

Suggested-by: Zidan Wang <zidan.wang@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:57 +08:00
Justin Waters
890b53ef86 ARM: dts: imx6q-ba16: Disable pwm2 by default
pwm2 is provided on the BA16 Q7 module, but is not used on any
of the current configurations. However, future platforms may
utilize this device, so we are simply disabling the node rather
than removing it completely.

Signed-off-by: Justin Waters <justin.waters@timeys.com>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:56 +08:00
Gary Bisson
36853f9c61 ARM: dts: imx: add Boundary Devices Nitrogen6_SoloX board
Based on i.MX6 SoloX with 1GB of RAM.

https://boundarydevices.com/product/nit6_solox-imx6/

Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:56 +08:00
Fabio Estevam
e0884948a4 ARM: dts: imx6qdl-sabresd: Pass the hannstar panel compatible string
It is preferred to use the panel compatible string rather than passing the
LCD timings in the device tree.

So pass the "hannstar,hsd100pxn1" compatible string to describe
the LVDS panel on this board.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:55 +08:00
Lothar Waßmann
8630743bbe ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard
This baseboard can be used with all TX6 SoMs, but only a certain set
of combinations can be ordered by default. Add support for these
combinations in mainline, so that users can easily adopt their own
combination of SoM and baseboard themselves.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:55 +08:00
Lothar Waßmann
168e046136 ARM: dts: imx6: add support for more Ka-Ro electronics modules
Add support for the following i.MX6 based modules from Ka-Ro
electronics GmbH:
TX6S-8034:
Processor    Freescale i.MX 6 Solo, 800MHz
RAM          256MiB DDR3 SDRAM
ROM          128MiB NAND Flash
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  industrial grade (-40°C/-25°C to 105°C Tj)

TX6S-8035:
Processor    Freescale i.MX 6 Solo, 800MHz
RAM          512MiB DDR3 SDRAM
ROM          4GiB eMMC
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  industrial grade (-40°C/-25°C to 105°C Tj)

TX6U-8033:
Processor    Freescale i.MX 6 Dual Lite, 800MHz
RAM          1GiB DDR3 SDRAM
ROM          4GiB eMMC
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  industrial grade (-40°C/-25°C to 105°C Tj)

TX6Q-1036:
Processor    Freescale i.MX 6Quad, 1GHz
RAM          1GB DDR3 SDRAM 64-bit
ROM          8GiB eMMC
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  Extended Consumer Grade (-20°C to 105°C Tj)

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:54 +08:00
Lothar Waßmann
720f4340e4 ARM: dts: imx6-tx6: enable support for rtscts on UARTs
Add missing pinctrl for the RTS/CTS lines to uart1 and set the
fsl,uart-has-rtscts property on all UARTs to enable support for HW
handshake.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:54 +08:00
Lothar Waßmann
96de03677f ARM: dts: imx6-tx6: remove LED pinctrl setting from hoggrp
Move the pinctrl setting for the board LED from the hoggrp node
to a separate node referenced by the LED driver, so that the pin is
free to be used for different purpose when the LED driver is disabled.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:53 +08:00
Lothar Waßmann
7281795fa4 ARM: dts: imx6-tx6: remove regulator bus
DT maintainers don't like the 'simple-bus' container around the
regulator nodes. So remove it.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:53 +08:00
Gary Bisson
a7574ab01c ARM: dts: imx: add Boundary Devices Nitrogen6_MAX QP board
Based on i.MX6 Quad Plus with 4GB of RAM.

https://boundarydevices.com/product/nitrogen6max/

Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:47:53 +08:00
Lothar Waßmann
9cbda37b87 ARM: dts: imx6qdl-tx6: add mdio node for ethernet phy
Add mdio node and an appropriate PHY configuration to enable use of
the PHY interrupt for link status changes.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:45:00 +08:00
Lothar Waßmann
c4aca663ae ARM: dts: imx6-tx6: remove container node around pinctrl nodes
Remove the function node around the pinctrl nodes that was obsoleted
by commit 5fcdf6a7ed ("pinctrl: imx: Allow parsing DT without
function nodes"), we can save this container node.

Also move the iomux node to the bottom of the file to improve
readability of the file.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:44:59 +08:00
Lothar Waßmann
0fd646d0e7 ARM: dts: imx6-tx6: disable the spi node by default
The spidev driver doesn't like to be instantiated via a naked 'spidev'
compatible, though it is very convenient to invoke it this way without
a dedicated SPI device for basic functional testing.
Disable the spi node by default to silence the WARN_ON() from the
spidev driver, but leave the configuration intact otherwise.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:44:59 +08:00
Lothar Waßmann
abe3e2b902 ARM: dts: imx6-tx6: cleanup; no functional change
Add an empty line between properties and subnode in the clocks node.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:44:59 +08:00
Lothar Waßmann
e06dd63024 ARM: dts: imx6-tx6: Relicense the Ka-Ro DT files under GPLv2/X11
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.

The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the imx6*-tx6* files to this combination.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:44:58 +08:00
Uwe Kleine-König
78e62436d5 ARM: dts: imx25-pinfunc: remove SION for pins with an UART handshaking input mode
With SION set the level on such a pin is reported to the UART. So for
example when the CS5 pin is configured for GPIO mode and the level
changes this triggers an RTS interrupt on uart5.

Adding some severity to this issue: The imx uart driver currently
doesn't handle correctly irqs for changes on RI and DCD which are
enabled automatically when the respective UART is driven in DTE mode
(that is, has the fsl,dte-mode property set in the device tree). This
results in a stuck machine because the irq isn't cleared and so stalls
the CPU.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:44:58 +08:00
Uwe Kleine-König
2fcc786bf5 ARM: dts: imx25-pinfunc: add all UART mux modes
Apart from a few additions this also contains two fixes where the daisy
chain input selection register was missing. Moreover dropped _MUX from
some pins for consistency.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:44:58 +08:00
Justin Waters
e85225d708 ARM: dts: imx: ba16: Add correct PCIe Tx Values
Utilize the new PCIe Tx configuration to properly support the correct
values.

Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:44:57 +08:00
Lothar Waßmann
cf4534824f ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL mainboard
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:44:57 +08:00
Lothar Waßmann
5434c913b6 ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules
The TXUL-0010/-0011 modules are Computers On Module manufactured by
  Ka-Ro electronics GmbH with the following characteristics:
  Processor    Freescale i.MX 6UltraLite MCIMX6G2, 528 MHz
  RAM          256MB 16-bit DDR3 SDRAM
  ROM          128MB NAND Flash (TXUL-0010) / 4GB eMMC (TXUL-0011)
  Power supply Single 3.3 to 5V
  Size         26mm SO-DIMM
  Temp. Range  -40°C to 85°C

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-13 17:44:57 +08:00
Linus Torvalds
f55532a0c0 Linux 4.6-rc1 2016-03-26 16:03:24 -07:00
Linus Torvalds
d5a38f6e46 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph updates from Sage Weil:
 "There is quite a bit here, including some overdue refactoring and
  cleanup on the mon_client and osd_client code from Ilya, scattered
  writeback support for CephFS and a pile of bug fixes from Zheng, and a
  few random cleanups and fixes from others"

[ I already decided not to pull this because of it having been rebased
  recently, but ended up changing my mind after all.  Next time I'll
  really hold people to it.  Oh well.   - Linus ]

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (34 commits)
  libceph: use KMEM_CACHE macro
  ceph: use kmem_cache_zalloc
  rbd: use KMEM_CACHE macro
  ceph: use lookup request to revalidate dentry
  ceph: kill ceph_get_dentry_parent_inode()
  ceph: fix security xattr deadlock
  ceph: don't request vxattrs from MDS
  ceph: fix mounting same fs multiple times
  ceph: remove unnecessary NULL check
  ceph: avoid updating directory inode's i_size accidentally
  ceph: fix race during filling readdir cache
  libceph: use sizeof_footer() more
  ceph: kill ceph_empty_snapc
  ceph: fix a wrong comparison
  ceph: replace CURRENT_TIME by current_fs_time()
  ceph: scattered page writeback
  libceph: add helper that duplicates last extent operation
  libceph: enable large, variable-sized OSD requests
  libceph: osdc->req_mempool should be backed by a slab pool
  libceph: make r_request msg_size calculation clearer
  ...
2016-03-26 15:53:16 -07:00
Linus Torvalds
698f415cf5 Merge tag 'ofs-pull-tag-1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux
Pull orangefs filesystem from Mike Marshall.

This finally merges the long-pending orangefs filesystem, which has been
much cleaned up with input from Al Viro over the last six months.  From
the documentation file:

 "OrangeFS is an LGPL userspace scale-out parallel storage system.  It
  is ideal for large storage problems faced by HPC, BigData, Streaming
  Video, Genomics, Bioinformatics.

  Orangefs, originally called PVFS, was first developed in 1993 by Walt
  Ligon and Eric Blumer as a parallel file system for Parallel Virtual
  Machine (PVM) as part of a NASA grant to study the I/O patterns of
  parallel programs.

  Orangefs features include:

    - Distributes file data among multiple file servers
    - Supports simultaneous access by multiple clients
    - Stores file data and metadata on servers using local file system
      and access methods
    - Userspace implementation is easy to install and maintain
    - Direct MPI support
    - Stateless"

see Documentation/filesystems/orangefs.txt for more in-depth details.

* tag 'ofs-pull-tag-1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux: (174 commits)
  orangefs: fix orangefs_superblock locking
  orangefs: fix do_readv_writev() handling of error halfway through
  orangefs: have ->kill_sb() evict the VFS side of things first
  orangefs: sanitize ->llseek()
  orangefs-bufmap.h: trim unused junk
  orangefs: saner calling conventions for getting a slot
  orangefs_copy_{to,from}_bufmap(): don't pass bufmap pointer
  orangefs: get rid of readdir_handle_s
  ornagefs: ensure that truncate has an up to date inode size
  orangefs: move code which sets i_link to orangefs_inode_getattr
  orangefs: remove needless wrapper around GFP_KERNEL
  orangefs: remove wrapper around mutex_lock(&inode->i_mutex)
  orangefs: refactor inode type or link_target change detection
  orangefs: use new getattr for revalidate and remove old getattr
  orangefs: use new getattr in inode getattr and permission
  orangefs: use new orangefs_inode_getattr to get size in write and llseek
  orangefs: use new orangefs_inode_getattr to create new inodes
  orangefs: rename orangefs_inode_getattr to orangefs_inode_old_getattr
  orangefs: remove inode->i_lock wrapper
  orangefs: put register_chrdev immediately before register_filesystem
  ...
2016-03-26 12:59:04 -07:00
Linus Torvalds
b4cec5f668 NTB bug fixes for tasklet from spinning forever, link errors,
translation window setup, NULL ptr dereference, and ntb-perf errors.
 Also, a modification to the driver API that makes _addr functions
 optional.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJW9rVgAAoJEG5mS6x6i9IjutEP/11ufWLOGHOOD4zAZ/Bb62MS
 YQXr0I/CUViEiV0Jaj254FmlYYafDAb5LfYVneVGalW3HvLMED069M7WEQyP7UqG
 4dTNWyktS6GkjrlejGzY2xrPXr8hG4GTrpkMgBo4uZol1n95VEe3IlOn4VheEwPz
 +RNioK1oBDV6f6JXjD5IH0FP+/Gn1VwxVPq/lXpFIZfw4FX1+pbTfjbNB2kkNOXM
 0adUEZdyritg3cqrecH1P+ewGYT5//S/ai/AgxghddJAwh2IHlf46ZdGiVH37Awd
 r6+EgqzdPiG5Qxlo2CTnu1gb4zsqXJYViWsM+vNIqJYCweD7ZoMuYy89mAf+l0kb
 a4kBi657qmEsalw4nqeMoZHuHdW2G9gA8UHmNyENRWmtHG7odVXGnR4PA0nE7kyw
 JPrNSHQ7mGgo+9wsvLYT6BAatpAjBIhE2wjrR8svS8qnP8jU9mjT3nTKAWKl1XO+
 YXbUwlqbiMaFzBNd327iyEBqoGU3j1ba+AiG3IBbiOxNJz1WnfFNvnuYMu4zuruZ
 KmdZlQTO5s2YPBIV+BgzPK6oRBCTxQrVBsRN2jn/i+02gAgB3uZeT3IhLCTLZhtf
 mT5/3yyvk6O8Hcs5VoSzyyzbAHIL0y/NEUR0jnOqZowwTx8ajg+owHAUgggUloHj
 wXALu1jc80GsOglBKU0Z
 =7DcD
 -----END PGP SIGNATURE-----

Merge tag 'ntb-4.6' of git://github.com/jonmason/ntb

Pull NTB bug fixes from Jon Mason:
 "NTB bug fixes for tasklet from spinning forever, link errors,
  translation window setup, NULL ptr dereference, and ntb-perf errors.

  Also, a modification to the driver API that makes _addr functions
  optional"

* tag 'ntb-4.6' of git://github.com/jonmason/ntb:
  NTB: Remove _addr functions from ntb_hw_amd
  NTB: Make _addr functions optional in the API
  NTB: Fix incorrect clean up routine in ntb_perf
  NTB: Fix incorrect return check in ntb_perf
  ntb: fix possible NULL dereference
  ntb: add missing setup of translation window
  ntb: stop link work when we do not have memory
  ntb: stop tasklet from spinning forever during shutdown.
  ntb: perf test: fix address space confusion
2016-03-26 11:37:42 -07:00