Unlike ADM1023 and compatible chips, NCT210 does not support a temperature
offset register. A real chip was found to have a chip revision of 0x3f.
Use it to detect NCT210 explicitly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips supported by the ADM1021 driver are also supported by the LM90
driver. Make that support official.
After this change, the adm1021 driver is only needed if the lm90 driver
is disabled. Also, the adm1021 driver misdetects a variety of chips as
MAX1617A, which is unwanted if any of those chips is in the system.
For this reason. make the adm1021 driver dependent on !SENSORS_LM90 to
show that it is not needed if the lm90 driver is enabled, and to avoid
misdetection if a chip supported by the lm90 driver is in the system.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Both chips are quite similar to other chips of this series, so add
support for them to the lm90 driver. Also mention ON Semiconductor NCT210,
which is pin and register compatible to ADM1021A.
None of the chips support the secondary manufacturer and chip ID registers
at 0x3e and 0x3f, but return 0 when reading from those registers.
Use that information to improve the accuracy of chip detection code.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX1617 and LM84 are stripped-down versions of LM90, so they can easily
be supported by the LM90 driver. The most difficult part is chip detection,
since those old chips do not support manufacturer ID or chip ID registers.
The "alarms" attribute is enabled for both chips to match the functionality
of the adm1021 driver. Chip detection was improved and is less prone to
misdetection than the chip detection in the adm1021 driver.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6642 is a reduced version of LM90 with no low limits and no conversion
rate register. Its alert functionality is broken, similar to many other
chips supported by the lm90 driver.
After this change, the stand-alone max6642 driver is only needed if the
lm90 driver is disabled. Make it dependent on SENSORS_LM90=n to show that
it is not needed if the lm90 driver is enabled.
A devicetree node is not added for this chip since it is quite unlikely
that such an old chip will ever be used in a devicetree based system.
It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6690 is all but identical to MAX6654. Revision 1 of its
datasheet lists the same chip ID as MAX6654, and a chip labeled
MAX6654 was found to have the chip ID listed as MAX6690 chip ID
in Revision 2 of its datasheet.
A devicetree node is not added for this chip since it is quite unlikely
that such an old chip will ever be used in a devicetree based system.
It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADT7481, ADT7482, and ADT7483 are similar to ADT7461, but support two
external temperature sensors, similar to MAX6695/6696. They support an
extended temperature range similar to ADT7461. Registers for the second
external channel can be accessed directly or by using the same method as
used by MAX6695/6696. For simplicity, the access method implemented for
MAX6695/6696 is used.
The chips support PEC (packet error checking). Set the PEC feature flag
and let the user decide if it should be enabled or not (it is by default
disabled).
Even though it is only documented for ADT7483, all three chips support a
secondary manufacturer ID register at 0x3e and a chip ID register at 0x3f.
Use the contents of those registers register for improved chip detection
accuracy. Add the same check to the ADT7461A detection code since this chip
also supports the same (undocumented) registers.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Reviewed-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike MAX6646/MAX6647/MAX6649, MAX6648 and MAX6692 only support
a temperature range of 0..127 degrees C. Separate support for the
two sets of chips to be able to support maximum temperature ranges
correctly for all chips. Introduce new feature flag to indicate
temperature support up to 255 degrees C.
Since the chips are almost identical except for the supported temperature
range, automatic chip detection is limited. Effectively this means that
MAX6648 may be mis-detected as MAX6649 when auto-detected, but there is
nothing we can do about that.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Revision 0 of the ADT7461 datasheet suggests that the chip supports PEC
(packet error checking). This information is gone in later versions of the
datasheet. Experiments show that PEC support on ADT7461 is similar to PEC
support in ADM1032, ie it is only supported for read operations. Add
support for it to the driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PEC (packet error checking) support for ADM1032 is currently only enabled
if the chip was auto-detected, but not if a chip is instantiated
explicitly. Always enable PEC support by introducing a chip feature flag
indicating partial PEC support. Also, for consistency, disable PEC support
by default to match existing functionality if the chip was not auto-
detected.
At the same time, introduce generic support for PEC with a separate feature
flag. This will be used when support for chips with full PEC functionality
is added.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.
Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.
Fixes: 24333ac26d ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719190525.61112-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the Maxim MAX6654 to the lm90 driver.
The MAX6654 is a temperature sensor, similar to the others,
but with some differences regarding the configuration
register, and the sampling rate at which extended resolution
becomes possible.
Signed-off-by: Josh Lehan <krellan@google.com>
Link: https://lore.kernel.org/r/20200513184248.145765-1-krellan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now that all files were converted to ReST format, rename them
and add an index.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
