When this failure occurs, we will clear card->plt_wake_cfg so that
device would initialize without wake up on external interrupt feature.
This feature specific code in suspend and resume handlers will be
skipped.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.9. Major changes:
ath10k
* add nl80211 testmode support for 10.4 firmware
* hide kernel addresses from logs using %pK format specifier
* implement NAPI support
* enable peer stats by default
ath9k
* use ieee80211_tx_status_noskb where possible
wil6210
* extract firmware capabilities from the firmware file
ath6kl
* enable firmware crash dumps on the AR6004
ath-current is also merged to fix a conflict in ath10k.
hw_4addr_pad was added to handle different types of padding
in 4-address rx frame. But this padding is not very specific
to 4-address, it can happen even with three address + ethernet
decap mode. Since the padding information can be obtained
through Rx desc for QCA99X0 and newer chips, this hw_param
is not needed any more.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In QCA99X0 (QCA99X0, QCA9984, QCA9888 and QCA4019) family chips,
hw adds padding at the begining of the rx payload to make L3
header 4-byte aligned. In the chips doing this type of padding,
the number of bytes padded will be indicated through msdu_end:info1.
Define a hw_rx_desc_ops wrapper to retrieve the number of padded
bytes and use this while doing undecap. This should fix padding
related issues with ethernt decap format with QCA99X0, QCA9984,
QCA9888 and QCA4019 hw.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[Rename operations to hw_ops for other purposes]
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are slight differences in Rx hw descriptor information
among different chips. So far driver does not use those new
information for any functionalities, but there is one important
information which is available from QCA99X0 onwards to indicate
the number of bytes that hw padded at the begining of the rx
payload and this information is needed to undecap the rx
packet. Add an abstraction for Rx desc to make use of the
new desc information available. The callback that this patch
defines to retrieve the padding bytes will be used in follow-up
patch.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[Rename operations to hw_ops for other purposes]
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to prepare for rx descriptor abstraction where we'll
be dereferencing ath10k_hw_params member in hw.h. Moreover
hw.h looks more suitable to house ath10k_hw_params definition
than core.h
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Helps to know the sta pointer.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: add %pK and remove the colon]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
IFTYPE_MESH_POINT need to rely on these for accurate path
selection metrics. Other modes will probably also find
them useful. Enabling peer stats has the side effect of
reducing max number of STAs from 128 to 118. There should
be negligible performance impact.
If users really need 128 STAs and don't mind losing out on
peer stats, they can still disable them:
echo 0 > debugfs/ieee80211/phyn/ath10k/peer_stats
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Trival fix to remove unused variable ar_pci in ath10k_pci_tx_pipe_cleanup
when building with W=1:
drivers/net/wireless/ath/ath10k/pci.c:1696:21: warning: variable
'ar_pci' set but not used [-Wunused-but-set-variable]
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
caldata is not being free'd on the error exit path, causing
a memory leak and data definitely should not be freed. Free
caldata instead of data.
Thanks to Kalle Valo for spotting that data should not be
free'd.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3c97f5de1f ("ath10k: implement NAPI support") conflicts with
ath-current. To avoid any merge problems merge ath-current to ath-next already now.
Conflicts:
drivers/net/wireless/ath/ath10k/htt_rx.c
carl9170_usb_stop() is used from several places to flush and cleanup any
pending work. The normal pattern is to send a request and wait for the
irq handler to call complete(). The completion is not reinitialized
during normal operation and as the old comment indicates it is important
to keep calls to wait_for_completion_timeout() and complete() balanced.
Calling complete_all() brings this equilibirum out of balance and needs
to be fixed by a reinit_completion(). But that opens a small race
window. It is possible that the sequence of complete_all(),
reinit_completion() is faster than the wait_for_completion_timeout() can
do its work. The wake up is not lost but the done counter test is after
reinit_completion() has been executed. The only reason we don't see
carl9170_exec_cmd() hang forever is we use the timeout version of
wait_for_copletion().
Let's fix this by reinitializing the completion (that is just setting
done counter to 0) just before we send out an request. Now,
carl9170_usb_stop() can be sure a complete() call is enough to make
progess since there is only one waiter at max. This is a common pattern
also seen in various drivers which use completion.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath6kl driver attempts to get the txpower value from the radio by first
clearing the existing stored value and then watching the value to become
non-zero.
APs allow setting client power to values from -127..127, but this radio
is not capable of setting values less then 0 and so will report txpower
as 0dbm for both negative and 0 client power values.
When the radio has txpower set to 0dbm txpower (equivalent to 1mw) the
ath6kl_cfg80211_get_txpower() function will remain in the
wait_event_interruptible_timeout() loop waiting for the value to be
non-zero, and will eventually timeout. This results in a 5 second delay in
response. However, the correct value of zero is eventually returned.
The 6004 defaults to 63dbm which is then limited by regulatory and
hardware limits with max of 18dbm (6003 max is 16dbm), therefore we can
use values larger then these to be able to determine when the value has
been updated.
To correct the issue, set the value to a nonsensical value (255) and wait
for it to change to the valid value.
Tested on both 6003 and 6004 based radios. Return value of zero is
correctly returned in an expected amount of time (similar to when
returning non-zero values) when AP client power is set to both 0 and
negative values.
Signed-off-by: Eric Bentley <eric.bentley@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The firmware crash dumps on the 6004 are the same as the 6003. Remove the
statement guarding it from dumping on the 6004. Renamed the
REG_DUMP_COUNT_AR6003 to reflect support on both chips.
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The constant "123", which is the number of elements in
mask_m / mask_p, is repeated several times in this function.
Replace memsets with array initialization, and replace a loop
conditional with ARRAY_SIZE() so that we don't repeat ourselves.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When user requests for survey dump data, driver is providing wrong survey
information. This information we sent is the survey data that we have
collected during previous user request.
This issue occurs because we request survey dump for wrong channel. With
this change, we correctly display the correct and current survey
information to userspace.
Fixes: fa7937e3d5 ("ath10k: update bss channel survey information")
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The error assigned does not seems to be used anywhere,
fixes nothing just a small cleanup
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For non-aggregated frames, ath9k was leaving handling of powersave
filtered packets to mac80211. This can be too slow if the intermediate
queue is already filled with packets and mac80211 does not immediately
send a new packet via drv_tx().
Improve response time with filtered frames by triggering clearing the
powersave filter internally.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It removes the need for undoing the padding changes to skb->data and it
improves performance by eliminating one tx status lookup per MPDU in the
status path. It is also useful for preparing a follow-up fix to better
handle powersave filtering.
A side effect is that these counters, available via debugfs, become now invalid:
* dot11TransmittedFragmentCount
* dot11FrameDuplicateCount,
* dot11ReceivedFragmentCount
* dot11MulticastReceivedFrameCount
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@qca.qualcomm.com: add a note about counters, thanks to Zefir Kurtisi]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 7a0adc83f3 ("ath10k: improve tx scheduling") is causing
severe throughput drop in multi client mode. This issue is originally
reported in veriwave setup with 50 clients with TCP downlink traffic.
While increasing number of clients, the average throughput drops
gradually. With 50 clients, the combined peak throughput is decreased
to 98 Mbps whereas reverting given commit restored it to 550 Mbps.
Processing txqs for every tx completion is causing overhead. Ideally for
management frame tx completion, pending txqs processing can be avoided.
The change partly reverts the commit "ath10k: improve tx scheduling".
Processing pending txqs after all skbs tx completion will yeild enough
room to burst tx frames.
Fixes: 7a0adc83f3 ("ath10k: improve tx scheduling")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add NAPI support for rx and tx completion. NAPI poll is scheduled
from interrupt handler. The design is as below
- on interrupt
- schedule napi and mask interrupts
- on poll
- process all pipes (no actual Tx/Rx)
- process Rx within budget
- if quota exceeds budget reschedule napi poll by returning budget
- process Tx completions and update budget if necessary
- process Tx fetch indications (pull-push)
- push any other pending Tx (if possible)
- before resched or napi completion replenish htt rx ring buffer
- if work done < budget, complete napi poll and unmask interrupts
This change also get rid of two tasklets (intr_tq and txrx_compl_task).
Measured peak throughput with NAPI on IPQ4019 platform in controlled
environment. No noticeable reduction in throughput is seen and also
observed improvements in CPU usage. Approx. 15% CPU usage got reduced
in UDP uplink case.
DL: AP DUT Tx
UL: AP DUT Rx
IPQ4019 (avg. cpu usage %)
========
TOT +NAPI
=========== =============
TCP DL 644 Mbps (42%) 645 Mbps (36%)
TCP UL 673 Mbps (30%) 675 Mbps (26%)
UDP DL 682 Mbps (49%) 680 Mbps (49%)
UDP UL 720 Mbps (28%) 717 Mbps (11%)
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The patch corrects the revision id register and uses it along with
magic value and chip version registers to download appropriate firmware
image.
PCIe8997 Z chipset variant code has been removed, as it won't be used in
production.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch:
- improves code layout
- removes a useless memset(0) for some memory allocated with kzalloc
- removes a useless if. We know that 'if (chan_band_tlv)' will succeed
because it has been tested a few lines above
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements pre and post FLR handlers to support PCIe FLR
functionality. Software cleanup is performed in pre-FLR whereas
firmware is downloaded and software is re-initialised in
post-FLR handler.
Following command triggers FLR.
echo "1" > /sys/bus/pci/devices/$NUMBER/reset
This feature can be used as a recovery mechanism when firmware gets
hang.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In brcmf_sdio_kso_control() there is a retry loop as hardware may take
time to settle. However, when the call to brcmf_sdiod_regrb() returns
an error it is due to SDIO access failure and it makes no sense to wait
for hardware to settle. This patch aborts the loop after a number of
subsequent access errors.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver already supports the bcm4339 chipset but only for the variant
that shares the same modalias as the bcm4335, ie. sdio:c00v02D0d4335.
It turns out that there are also bcm4339 devices out there that have a
more distiguishable modalias sdio:c00v02D0d4339.
Reported-by: Steve deRosier <derosier@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the newly added linux/bitfield.h.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to include linux/version.h in a in-tree
driver.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove redefinition of GENMASK which should not be there
in the upstream version of the code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds cfg80211 testmode support so that userspace tools can
download necessary commands to firmware during manufacturing mode tests.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
By default normal mode is chosen when driver is loaded. This
patch adds a provision to choose manufacturing mode via module
parameters.
Below command loads driver in manufacturing mode
insmod mwifiex.ko mfg_mode=1.
Tested-by: chunfan chen <jeffc@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git fixes for 4.8. Major changes:
ath10k
* fix racy rx status retrieval from htt context
* QCA9887 support is not experimental anymore, remove the warning message
ath9k
* fix regression with led GPIOs
* fix AR5416 GPIO access warning
User-space can choose to omit NL80211_ATTR_SSID and only provide raw
IE TLV data. When doing so it can provide SSID IE with length exceeding
the allowed size. The driver further processes this IE copying it
into a local variable without checking the length. Hence stack can be
corrupted and used as exploit.
Cc: stable@vger.kernel.org # v4.7
Reported-by: Daxing Guo <freener.gdx@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A regression was introduced in commit id 79d4db1214 ("ath9k: cleanup
led_pin initial") that broken the WLAN status led on my laptop with
AR9287 after suspending and resuming.
Steps to reproduce:
* Suspend (laptop)
* Resume (laptop)
* Observe that the WLAN led no longer turns ON/OFF depending on the
status and is always red
Even though for my case it only needs to be set to OUT in ath9k_start
but for consistency bring back the IN direction setting as well.
Fixes: 79d4db1214 ("ath9k: cleanup led_pin initial")
Cc: Miaoqing Pan <miaoqing@codeaurora.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: <stable@vger.kernel.org> # 4.7+
Link: https://bugzilla.kernel.org/show_bug.cgi?id=151711
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
%ul was likely meant as %lu to print an unsigned long,
not an unsigned with a letter l at the end.
But in fact the value printed is u32 anyway, so just drop
the l completely.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Printing about 3000 lines like this
[ 20.691850] mwifiex_pcie 0000:02:00.0: .
[ 20.693466] mwifiex_pcie 0000:02:00.0: .
is not useful. If FW downloading will be interrupted, we will get
proper error message about that.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For debugging purpose print content of reg->fw_status register and other
variables values when waiting for firmware ready event.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Printing ret and adapter->winner do not provide any useful information
as those are always 0 at point where the massage is printed. Print value
read from reg->fw_status register instead.
Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add time sync configuration api.
The new api allows to configure the synchronization
mode (STA/AP/MESH) and (in case of Mesh mode) the
master address of each zone.
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The struct cfg80211_pmksa defines its bssid field as:
const u8 *bssid;
contrary to struct brcmf_pmksa, which uses:
u8 bssid[ETH_ALEN];
Therefore in brcmf_cfg80211_del_pmksa(), &pmksa->bssid takes the address
of this field (of type u8**), not the one of its content (which would be
u8*). Remove the & operator to make brcmf_dbg("%pM") and memcmp()
behave as expected.
This bug have been found using a custom static checker (which checks the
usage of %p... attributes at build time). It has been introduced in
commit 6c404f34f2 ("brcmfmac: Cleanup pmksa cache handling code"),
which replaced pmksa->bssid by &pmksa->bssid while refactoring the code,
without modifying struct cfg80211_pmksa definition.
Replace &pmk[i].bssid with pmk[i].bssid too to make the code clearer,
this change does not affect the semantic.
Fixes: 6c404f34f2 ("brcmfmac: Cleanup pmksa cache handling code")
Cc: stable@vger.kernel.org
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The AE1200 comes with different revisions of the BCM43235 chipset,
but all have the same USB ID. Only revision 3 can be supported.
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some RTL8821AE devices sold in Great Britain have the country code of
0x25 encoded in their EEPROM. This value is not tested in the routine
that establishes the regulatory info for the chip. The fix is to set
this code to have the same capabilities as the EU countries. In addition,
the channels allowed for COUNTRY_CODE_ETSI were more properly suited
for China and Israel, not the EU. This problem has also been fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On my home network rtl8xxxu is spamming the log with
IEEE80211_AMPDU_RX_START / IEEE80211_AMPDU_RX_STOP every few seconds
turn these messages into debug messages.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
[kvalo@codeaurora.org: fix commit title]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes the following sparse warning:
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:898:1: warning:
symbol 'rtl8xxxu_gen1_h2c_cmd' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Split the filling of TX descriptors into a generic portion used on all
devices, and format specific helper functions provided in the fops
structure.
This also cleaned up some mess, even if non harmful, in the handling
of txdesc40 descriptors, where the code randomly would switch between
the pointer to tx_desc and tx_desc40.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Another patch to move this detection out of the code handling the TX
descriptor update.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to be able to split out the TX descriptor handling code,
determine in advance the need to mark SGI.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Calculating the value in one place rather than using one calculation
in one place and a different one for management frames in another
location makes little sense.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not rely on TX descriptor size to determine the thermal meter
type.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This leaves space for a few more flags within the same space.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use a fileops flag to indicate whether the device has TX report timer
support. This will make it easier to include future devices such as
8188eu to use the TX report timer.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These are primarily needed for SDIO/PCI parts, but the vendor driver
still sets them for some USB devices.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This adds TX antenna selection bit defines for OFDM mode.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With all devices now offering fops->total_page_num, get rid of the
if mess for setting the TX buffer boundary.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Switching over the old devices to use the new function allows us to
get rid of this legacy.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was the last user of the old
rtl8xxxu_old_init_queue_reserved_page() which can now be removed.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This changes the pub-queue value written to REQ_RQPN, however the old
code used a hard coded minimum value assuming there would always be an
active lo-queue, even when no USB EP was found for it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This switches the 8723b driver to use the new
rtl8xxxu_init_queue_reserved_page() function.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is an rtl8192eu based dongle (the v1 is an rtl8192cu). Reported
and tested by Myckel Habets.
Reported-by: Myckel Habets <myckel@sdf.lonestar.org>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For some reason we lost the code bailing if rtl8xxxu_init_device()
returned an error.
This catches the error and also cleans up the error handling.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
D-Link DWA-121 is reported as working.
Reported-by: Stefano Bravi <stefanobravi69@libero.it>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Successfully tested by Jocelyn Mayer
Reported-by: J. Mayer <l_indien@magic.fr>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This field was added to wl_sta struct to get hw in situations
where it was not given to driver by mac80211. In our case,
get_expected_throughput op did not send hw to driver.
This patch reverts the change, as it is no longer needed due to commit
4fdbc67a25 ("mac80211: call get_expected_throughput only after adding
station") as hw is now sent as a parameter.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of (rtlhal->oem_id != RT_CID_DEFAULT), the function directly
returns and leaks the already allocated hwinfo memory. Go through the
correct exit path.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case rtl_get_hwinfo() fails, the function directly returns and leaks the
already allocated hwinfo memory. Go through the correct exit path.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We get 1 warning when building kernel with W=1:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/tracepoint.c:23:6: warning: no previous prototype for '__brcmf_err' [-Wmissing-prototypes]
In fact, this function is declared in brcmfmac/debug.h, so this patch
adds missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The IEEE80211_STYPE_ACTION case is missing a break in the switch
statement, causing it to fall through to the default case that
reports a debug message about an unknown frame subtype. Fix this
by adding in the missing break statement.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We know that 'retval = 0' because it has been tested a few lines above.
So, if 'devm_kmalloc' fails, 0 will be returned instead of an error code.
Return -ENOMEM instead.
Fixes: 8b4c000931 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch creates custom regulatory rules based on the information
received from firmware and enable them during wiphy registration.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds command preparation and response handling for
CHAN_REGION_CFG command. These changes are prerequisites for adding
custom regulatory domain support.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AID gets updated during TDLS setup, but modified value isn't reflected
in "priv->assoc_rsp_buf". This causes TDLS setup failure. The problem is
fixed here.
Fixes: 4aff53ef18 ("mwifiex: parsing aid while receiving..")
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch should be a no-op. It just simplifies code by using the name of
a variable instead of its type when calling 'sizeof'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In 'mwifiex_get_ver_ext', we have:
struct mwifiex_ver_ext ver_ext;
memset(&ver_ext, 0, sizeof(struct host_cmd_ds_version_ext));
This is likely that memset'ing sizeof(struct mwifiex_ver_ext) was expected.
Remove the ambiguity by using the variable name directly instead of its
type.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If sta == NULL, the changed line will not be reached.
So no need to check that sta != NULL here.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
EEPROM size calculated in 16-bit words, so we should take into account
this fact during buffer allocation.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Likely wl3501_reset should acquire spinlock as wl3501_{open, close}.
One of calls of wl3501_reset has been already protected.
The others were unprotected and might lead to a race condition.
The patch adds spinlock into the wl3501_reset and removes it from
wl3501_tx_timeout.
Found by Linux Driver Verification project (linuxtesting.org)
Signed-off-by: Pavel Andrianov <andrianov@ispras.ru>
Acked-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We are using mac as source address in a memcpy.
In the lines below we can assume mac is not NULL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
for_each_property_of_node is only executed if the
property prop is not NULL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that firmware sends RADAR detected event without
specifying bss_num/bss_type. Also, the event body is empty.
Currently the event is being ignored by driver.
This patch checks on which interface 11H is active, accordingly fills
bss_num/bss_type and handles the event. Condition
"if (le32_to_cpu(rdr_event->passed))" which always fails is also removed.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds HT support for adhoc station. Firmware will upload
ibss sta connect event with beacon data, whenever new station joins
the adhoc network. Driver will check the HT IE and decide whether to
support HT aggreagation or not.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Disconnect message in mwifiex_reset_connect_state() would displays
necessary information. We unnecessarily have exactly same message in
cfg80211_disconnect(). As priv->cfg_bssid is cleared at this point of
time, it prints incorrect(all zero) MAC.
This message is removed here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware may filter and drop packets under certain condition, for
example, ARP SA=DA packet. this event will be used to synchronize
the Rx Block Acknowledgment (BA) window bitmap and to fill any holes
in driver side.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch advertises RANDOM_MAC_ADDR feature to cfg80211. It allow the
application to issue scan with a MAC address and mask. Random MACs are
generated and used in probe requests sent for scanning until it is changed
by the application or device is restarted.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Recent patch "mwifiex: fix NULL pointer" skips extended scan event
handling when suspend is in progress. It created a problem for scan
after interface disabled/enabled case.
This patch solves the problem by checking netif_running() status.
Fixes:16d25da94f3d654 ("mwifiex: fix NULL pointer dereference during suspend")
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
region code is an EEPROM setting received from firmware. Let's display
this in debugfs along with other information.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver sends and recives information to and from the firmware.
Correct endianness should be ensured as firmware follows little
endian format and host can be little/big endian.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes the following sparse warning:
drivers/net/wireless/ti/wlcore/spi.c:87:34: warning:
symbol 'wilink_data' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix coccicheck warning which recommends to
use memdup_user() instead of reimplementing its
code.
This patch fixes below coccicheck warnings:
drivers/net/wireless/intersil/hostap/hostap_ioctl.c:3044:9-16: WARNING
opportunity for memdup_user
drivers/net/wireless/intersil/hostap/hostap_ioctl.c:3806:9-16: WARNING
opportunity for memdup_user
Signed-off-by: Rajan Vaja <rajan.vaja@gmail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We get 1 warning about global functions without a declaration
in the ath9k gpio driver when building with W=1:
drivers/net/wireless/ath/ath9k/gpio.c:25:6: warning: no previous prototype for 'ath_fill_led_pin' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is declared
and don't need a declaration, but can be made static.
so this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Trivial fix to spelling mistake in ath10k_warn message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Older firmware with HTT delivers incorrect tx status for null func
frames to driver, but this fixed in 10.2 and 10.4 firmware versions.
Also this workaround results in reporting of incorrect null func status
for 10.4. Fix this is by introducing a firmware feature flag for 10.4
so that this workaround is skipped and proper tx status for null func
frames are reported
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 97f2645f35 ("tree-wide: replace config_enabled() with
IS_ENABLED()") mostly did away with config_enabled().
This is one of the postponed TODO items as config_enabled() is used
for a tristate option here. Theoretically, config_enabled() is
equivalent to IS_BUILTIN(), but I guess IS_REACHABLE() is the best
fit for this case because both CONFIG_HWMON and CONFIG_ATH10K are
tristate.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For 10.4 fw versions, dbglog module id has been extended from u32
to u64, hence this patch fixes the same in the ath10k driver side.
This patch doesn't break the older 10.4 releases. The FW change
is already present in the older FWs.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
waiter context waker context
scan.started
------------
ath10k_start_scan()
lockdep_assert_held(conf_mutex)
auth10k_wmi_start_scan()
wait_for_completion_timeout(scan.started)
ath10k_wmi_event_scan_start_failed()
complete(scan.started)
ath10k_wmi_event_scan_started()
complete(scan.started)
scan.completed
--------------
ath10k_scan_stop()
lockdep_assert_held(conf_mutex)
ath10k_wmi_stop_scan()
wait_for_completion_timeout(scan.completed)
__ath10k_scan_finish()
complete(scan.completed)
scan.on_channel
---------------
ath10k_remain_on_channel()
mutex_lock(conf_mutex)
ath10k_start_scan()
wait_for_completion_timeout(scan.on_channel)
ath10k_wmi_event_scan_foreign_chan()
complete(scan.on_channel)
offchan_tx_completed
--------------------
ath10k_offchan_tx_work()
mutex_lock(conf_mutex)
reinit_completion(offchan_tx_completed)
wait_for_completion_timeout(offchan_tx_completed)
ath10k_report_offchain_tx()
complete(offchan_tx_completed)
install_key_done
----------------
ath10k_install_key()
lockep_assert_held(conf_mutex)
reinit_completion(install_key_done)
wait_for_completion_timeout(install_key_done)
ath10k_htt_t2h_msg_handler()
complete(install_key_done)
vdev_setup_done
---------------
ath10k_monitor_vdev_start()
lockdep_assert_held(conf_mutex)
reinit_completion(vdev_setup_done)
ath10k_vdev_setup_sync()
wait_for_completion_timeout(vdev_setup_done)
ath10k_wmi_event_vdev_start_resp()
complete(vdev_setup_done)
ath10k_monitor_vdev_stop()
lockdep_assert_held(conf_mutex)
reinit_completion(vdev_setup_done()
ath10k_vdev_setup_sync()
wait_for_completion_timeout(vdev_setup_done)
ath10k_wmi_event_vdev_stopped()
complete(vdev_setup_done)
thermal.wmi_sync
----------------
ath10k_thermal_show_temp()
mutex_lock(conf_mutex)
reinit_completion(thermal.wmi_sync)
wait_for_completion_timeout(thermal.wmi_sync)
ath10k_thermal_event_temperature()
complete(thermal.wmi_sync)
bss_survey_done
---------------
ath10k_mac_update_bss_chan_survey
lockdep_assert_held(conf_mutex)
reinit_completion(bss_survey_done)
wait_for_completion_timeout(bss_survey_done)
ath10k_wmi_event_pdev_bss_chan_info()
complete(bss_survey_done)
All complete() calls happen while the conf_mutex is taken. That means
at max one waiter is possible.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the wake tx queue path, we are not checking if the frame to be sent
takes management path or not. For eg. QOS null func frame coming here will
take the management path. Since we are not incrementing the descriptor
counter (num_pending_mgmt_tx) w.r.t tx management, on tx completion it is
possible to see negative values.
When the above counter reaches a negative value, we will not be sending a
probe response out.
if (is_presp &&
ar->hw_params.max_probe_resp_desc_thres < htt->num_pending_mgmt_tx)
For IPQ4019, max_probe_resp_desc_thres (u32) is 24 is compared against
num_pending_mgmt_tx (int) and the above condtions comes true if the counter
is negative and we drop the probe response.
To avoid this, check on the wake tx queue path as well for the tx path of
the frame and increment the appropriate counters
Fixes: cac085524c "ath10k: move mgmt descriptor limit handle under mgmt_tx"
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
txqs_lock is interfering with wake_tx_queue submitting more frames.
so queues don't get filled in and don't keep firmware/hardware busy
enough. This change helps to reduce the txqs_lock contention and
wake_tx_queue() blockage to being possible in txrx_unref().
To reduce turn around time of wake_tx_queue ops and to maintain fairness
among all txqs, the callback is updated to push first txq alone from
pending list for every wake_tx_queue call. Remaining txqs will be
processed later upon tx completion.
Below improvements are observed in push-only mode and validated on
IPQ4019 platform. With this change, in AP mode ~10Mbps increase is
observed in downlink (AP -> STA) traffic and approx. 5-10% of CPU
usage is reduced.
Major improvement is observed in 1-hop Mesh mode topology in 11ACVHT80.
Compared to Infra mode, CPU overhead is higher in Mesh mode due to path
lookup and no fast-xmit support. So reducing spin lock contention is
helping in Mesh.
TOT +change
-------- --------
TCP DL 545 Mbps 595 Mbps
TCP UL 555 Mbps 585 Mbps
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'WMI_10_4_WDS_PEER_EVENTID' is not yet handled/implemented for WDS mode,
as of now suppress the warning message "Unknown eventid: 36903"
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent commit 46f6b06050 ("mac80211: Encrypt "Group addressed privacy" action
frames") encrypts group privacy action frames. But qca99x0 family chipset
delivers broadcast/multicast management frames as encrypted and it should be
decrypted by mac80211. Setting RX_FLAG_DECRYPTED stats for those frames is
breaking mesh connection establishment.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With the %pK format specifier we hide the kernel addresses
with the help of kptr_restrict sysctl.
In this patch, %p is changed to %pK in the driver code.
The sysctl is documented in Documentation/sysctl/kernel.txt.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT service has missed in
the commit 7e247a9e88 ("ath10k: add dynamic tx mode switch
config support for qca4019"). This patch adds the service to
avoid mismatch between host and target.
Fixes: 7e247a9e88 ("ath10k: add dynamic tx mode switch config support for qca4019")
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the FW version is taken from the sw_version field
of the FW ready event. This version is based on internal
version control revision and it is difficult to map to actual
FW version.
Fix this by using the actual FW version stored in the FW file
header record.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When driver is loaded, extract a capabilities record
from the FW file. This record contains bits indicating
which optional features are supported by this FW.
The driver can use this information to determine
which functionality to support and/or expose to user
space.
The extraction is done before wiphy structure is
registered, because the capabilities can affect
information published by the this structure.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the places that check wil->scan_request and
call cfg80211_scan_done are not consistently protected,
so there is a risk that cfg80211_scan_done will be called
with NULL scan_request, causing a kernel crash.
Fix this by using p2p_wdev_mutex in few other places
that access scan_request. This makes sense since
scan_request may point to p2p_wdev, and it is not worth
the extra complexity of adding a new mutex.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW Rx filters and masks are not configured
properly by firmware during boot sequences. The
MAC_PCU_ADDR1 is set to 0s instead of 1s which
allows the HW to ACK any frame that passes through
MAC_PCU_RX_FILTER. The MAC_PCU_RX_FILTER itself
is misconfigured on boot as well.
The combination of these bugs ended up with the
following manifestations:
- "no channel configured; ignoring frame(s)!"
warnings in the driver
- spurious ACKs (transmission) on the air during
firmware bootup sequences
The former was a long standing and known bug
originally though mostly harmless.
However Marek recently discovered that this
problem also involves ACKing *all* frames the HW
receives (including beacons ;). Such frames
are delivered to host and generate the former
warning as well.
This could be a problem with regulatory compliance
in some rare cases (e.g. Taiwan which forbids
transmissions on channel 36 which is the default
bootup channel on 5Ghz band cards). The good news
is that it'd require someone else to violate
regulatory first to coerce our device to generate
and transmit an ACK.
The problem could be reproduced in a rather busy
environment that has a lot of APs. The likelihood
could be increased by injecting an msleep() of
5000 or longer immediately after
ath10k_htt_setup() in ath10k_core_start().
The reason why the former warnings were only
showing up seldom is because the device was either
quickly reset again (i.e. during firmware probing)
or wmi vdev was created (which fixes hw and fw
states).
It is technically possible for host driver to
override adequate hw registers however this can't
work reliably because the bug root cause lies in
incorrect firmware state on boot (internal
structure used to program MAC_PCU_ADDR1 is not
properly initialized) and only vdev create/delete
events can fix it. This is why the patch takes
dummy vdev approach.
This could be fixed in firmware as well but having
this fixed in driver is more robust, most notably
when thinking of users of older firmware such as
999.999.0.636.
Reported-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows placing command barriers for explicit
serializing and synchronizing state.
Useful for future driver development.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Will be useful for implementing command barriers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Will be useful for implementing command barriers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds testmode support for 10.4 based chipsets
and added code swap support for UTF binary.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently testmode events for 10.x firmware are processed from
10.1 wmi event processing. This patch is used to handle testmode
events in 10.2 and 10.4 based firmware.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Preparation to make use of firmware_swap_code_seg_info for UTF binary.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Support for QCA9887 is no longer experimental and if there are any issues
we need to address them
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If device family is 8000 then iwl_pcie_load_cpu_sections()
won't be called at all (iwl_pcie_load_cpu_sections_8000() is
called in that case) so this piece of code never gets called.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Turns out we should access TFH relative addresses.
Also, the FH_UCODE_LOAD_STATUS was replaced by
UREG_UCODE_LOAD_STATUS.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Up till now we accessed SCD configuration only for initial
configuration and for enabling command queue.
For a000 generation the command queue is open by default
and firmware configures the rest. No driver SCD accesses
are expected. Make sure this is the case.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new config struct for the new 9170 series and add
the first PCI ID for it.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new config struct for the new 9270 series and add
the first PCI ID for it.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new series to the 9000 series called 9460.
In addition, add a new PCI ID that is the 9460 new series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rename and reorder the 9000 series configuration structs:
- struct containing configuration of 5165 was renamed to 9000.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Every active TXQ is assigned to a TID given through the
SCD_CONFIG_CMD, and acts as an identifier in the FW. However,
there may be cases this ownership needs to be changed.
For example, in the following scenario:
1. TID x is owner of a queue
2. Due to a shortage of queues, TID y and z share with x
3. TID x becomes inactive and needs to be removed from the
shared queue.
In this scenario, if another queue is freed and traffic on x
continues, we can't allocate it a new queue as long as it is
the owner of the first queue.
Support moving ownership of a TXQ to a different TID (same
STA) without stopping the queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to the addition of another option in the SCD_CONFIG_CMD's
%enable field, change the assignment of this field to use
defines rather than hard-code the value itself.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When working in DQA mode, if a queue is shared and a HW restart
occurs, there might be a possible race condition between
stations on the queues, and an existing queue might be left
with no queues.
To solve this, make sure in DQA mode to re-assign the same
queues as before the HW restart.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending the SCD_QUEUE_CONFIG command, the queue is
associated to a specific TID. If later there is a need to
use this TID on a different queue instead, it first needs to
be unassociated from the first queue.
Keep track for every queue what TID is associated with it.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a shared queue becomes unshared, aggregations should be
re-enabled if they've existed before. Make sure that they do
this, if required.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For a000 devices there is a support of 64 bit DMA addressing.
The paging command was changed accordingly - support it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for installing and removing GMAC key
for newer FW versions that support GCM and MFP.
GMAC provides authentication and integrity for multicast management
frames.
Firmware API was changed, update the driver accordingly.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 9000 hardware will de-aggregate AMSDUs. In the process
it will copy the mac header "as is" to the new MPDUs.
This means driver should allow the same PN for MPDUs originated
from the same AMSDU.
Do that by incrementing the PN only for the last MPDU in the
sequence.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwlmvm driver supports channel width change in AP mode. Add the
proper flag.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
fw-dbg code return ret but that variable was either 0
or not initialised. Return 0 always.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 6a95126763 ("iwlwifi: mvm: send dbg config hcmds to fw if set in tlv")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the user really wanted a dump on P2P Client, he
coudln't get it because we checked vif->type but didn't
take vif->p2p into account. Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ath.git fixes for 4.8. Major changes:
ath9k
* fix regression in client mode beacon configuration
* fix a station pointer which resulted in spurious crashes
A station pointer can be passed to the driver on tx, before it has been
marked as associated. Since ath9k_sta_state was initializing the entry
too late, it resulted in some spurious crashes.
Fixes: df3c6eb34d ("ath9k: Use sta_state() callback")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently wiphy structure is initialized and registered
in wil_if_alloc, before some information is available such
as MAC address and capabilities. As a result there is a
small chance user space will get incorrect information
from calls such as NL80211_CMD_GET_WIPHY.
Fix this by seperating the registration and moving it
to wil_if_add which is executed later, after all
relevant information is known.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
txdata->enabled is used in order to determine if the TX vring
is valid. As the data transmit is handled in a different context,
in case txdata->enabled is set before vring->hwtail is updated,
an old or corrupted vring->hwtail can be used.
Protect setting of txdata->enabled and vring->hwtail to prevent a
case where TX vring start handling TX packets before setting
vring->hwtail.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Stations disconnection is executed as part of wil_reset so no
need to do it in wil_down.
Removal of the disconnect operation will also preserve the lock
of wil->mutex during the whole reset flow and prevent handling of
connect event while resetting.
Set wil_status_resetting in earlier stage in the flow to prevent
double resetting call in case communication with FW fails while
bringing the interface down.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
fix stop p2p device handling to identify between search
and listen and update the upper layers with the appropriate
notification.
The stop of p2p radio operations also needs to be performed
in __wil_down.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Change the logging category of HALP functions from
MISC to IRQ, since the HALP mechanism is closely
related to interrupts. Both HALP and IRQ create
a heavy load of logging messages when enabled,
so their logging is typically disabled during normal debug
scenarios. Having them in the same logging category
will make it easier to disable logging for both in one go.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to the spec the PN should be calculated per TID.
In the current implementation, the PN and key_set were set
only for TID 0, therefore only traffic for TID 0 was supported.
In order to support all TIDs, the key_set and PN should be set
for all the TIDs.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case HALP vote times out, we need to mask the HALP IRQ, as done
in case the interrupt is received, as this interrupt should be
set until completion of the low latency operation.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
just to comply with current ath9k_hw_nvram_read to return value, hence
behaving reacting accordingly.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes smatch warning:
ath9k_vif_iter_set_beacon() warn if statement not indented
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes host prepares and downloads a large amsdu packet to firmware
which leads to a memory corruption in firmware.
The reason is __dev_alloc_skb() may allocate larger buffer than required
size. This patch solves the problem by checking "adapter->tx_buf_size"
instead of relying on skb_tailroom().
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Buffers powersave frame test is reversed in cfg80211, fix from Felix
Fietkau.
2) Remove bogus WARN_ON in openvswitch, from Jarno Rajahalme.
3) Fix some tg3 ethtool logic bugs, and one that would cause no
interrupts to be generated when rx-coalescing is set to 0. From
Satish Baddipadige and Siva Reddy Kallam.
4) QLCNIC mailbox corruption and napi budget handling fix from Manish
Chopra.
5) Fix fib_trie logic when walking the trie during /proc/net/route
output than can access a stale node pointer. From David Forster.
6) Several sctp_diag fixes from Phil Sutter.
7) PAUSE frame handling fixes in mlxsw driver from Ido Schimmel.
8) Checksum fixup fixes in bpf from Daniel Borkmann.
9) Memork leaks in nfnetlink, from Liping Zhang.
10) Use after free in rxrpc, from David Howells.
11) Use after free in new skb_array code of macvtap driver, from Jason
Wang.
12) Calipso resource leak, from Colin Ian King.
13) mediatek bug fixes (missing stats sync init, etc.) from Sean Wang.
14) Fix bpf non-linear packet write helpers, from Daniel Borkmann.
15) Fix lockdep splats in macsec, from Sabrina Dubroca.
16) hv_netvsc bug fixes from Vitaly Kuznetsov, mostly to do with VF
handling.
17) Various tc-action bug fixes, from CONG Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net_sched: allow flushing tc police actions
net_sched: unify the init logic for act_police
net_sched: convert tcf_exts from list to pointer array
net_sched: move tc offload macros to pkt_cls.h
net_sched: fix a typo in tc_for_each_action()
net_sched: remove an unnecessary list_del()
net_sched: remove the leftover cleanup_a()
mlxsw: spectrum: Allow packets to be trapped from any PG
mlxsw: spectrum: Unmap 802.1Q FID before destroying it
mlxsw: spectrum: Add missing rollbacks in error path
mlxsw: reg: Fix missing op field fill-up
mlxsw: spectrum: Trap loop-backed packets
mlxsw: spectrum: Add missing packet traps
mlxsw: spectrum: Mark port as active before registering it
mlxsw: spectrum: Create PVID vPort before registering netdevice
mlxsw: spectrum: Remove redundant errors from the code
mlxsw: spectrum: Don't return upon error in removal path
i40e: check for and deal with non-contiguous TCs
ixgbe: Re-enable ability to toggle VLAN filtering
ixgbe: Force VLNCTRL.VFE to be set in all VMDq paths
...
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable is added to allow the driver an easy access to
it's own hw->priv when the op is invoked.
This fixes a crash in wlcore because it was relying on a
station pointer that wasn't initialized yet. It's the wrong
way to fix the crash, but it solves the problem for now and
it does make sense to have the hw pointer here.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[rewrite commit message, fix indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ret variable is unused in wlcore_probe_of()
Remove it for fixing build warning.
Fixes: 01efe65aba ("wlcore: spi: add wl18xx support")
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.8. Major changes:
ath9k
* implement temperature compensation support for AR9003+
ath10k
* disable wake_tx_queue() mac80211 op for older devices to workaround
throughput regression
For rtl8188ee, we pass -Idrivers/net/wireless/rtlwifi/ to gcc,
however that directy no longer exists, so evidently this option
is no longer required here and can be removed to avoid a warning
when building with 'make W=1' or 'gcc -Wmissing-include-dirs'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for using with both wl12xx and wl18xx.
- all wilink family needs special init command for entering wspi mode.
extra clock cycles should be sent after the spi init command while the
cs pin is high.
- Use inverted chip select for sending a dummy 4 bytes command that
completes the init stage.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wlc_phy_txpower_get_current() does a logical OR of power->flags, which
presumes that power.flags was initiliazed earlier by the caller,
unfortunately, this is not the case, so make sure we zero out the struct
tx_power before calling into wlc_phy_txpower_get_current().
Reported-by: coverity (CID 146011)
Fixes: 5b435de0d7 ("net: wireless: add brcm80211 drivers")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case dma_mapping_error() returns an error in dma_rxfill, we would be
leaking a packet that we allocated with brcmu_pkt_buf_get_skb().
Reported-by: coverity (CID 1081819)
Fixes: 67d0cf50bd ("brcmsmac: Fix WARNING caused by lack of calls to dma_mapping_error()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case brcmf_sdiod_recv_chain() cannot complete a succeful call to
brcmf_sdiod_buffrw, we would be leaking glom_skb and not free it as we
should, fix this.
Reported-by: coverity (CID 1164856)
Fixes: a413e39a38 ("brcmfmac: fix brcmf_sdcard_recv_chain() for host without sg support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reduce indentation, use a variable to save a few pointer dereferences
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AR_PHY_65NM_CH0_THERM and AR_CH0_THERM were supposed to refer to the
same register, however they had different SREV checks.
Remove the duplicate and use the checks. Since there were other SREV
checks present in the only place that uses this, this will probaby not
affect runtime behavior.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The register layout of AR_PHY_SPECTRAL_SCAN has changed, only AR9280
uses the old layout
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There were two paths in the code for "external" eeprom sources. The code
in eeprom.c only handled the cases where the eeprom data was loaded via
request_firmware. ahb.c and pci.c on the other hand had some duplicate
code which was only used when the eeprom data was passed via
ath9k_platform_data.
With this change all eeprom data handling is now unified in eeprom.c.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When an NL80211_DISCONNECT is sent to cfg80211, the driver's cfg80211
disconnect function sets the sme_state to SME_DISCONNECTED before receiving
a WMI_DISCONNECT_EVENT from the firmware. This caused cfg80211 to not know
that the connection is disconnected because the driver fails to notify
cfg80211 upon receiving WMI_DISCONNECT_EVENT from the firmware believing
it is already disconnected.
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When disabling tethering after having enabled it, the ath6kl driver does
not set the IFF_LOWER_UP flag to 0 (carrier off) on the wlan interface.
The upper layers (eg. connman) are not notified of the tethering mode
status change. So, tethering can not be activated anymore.
This patch adds a netif_carrier_off() call when stopping AP mode to fix
the problem.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One minute after a successful connection, the kernel checks if the
frequency and the channel width are well configured for the country we
are in. (regulatory domain)
ath6kl driver was setting the NL80211_CHAN_HT20 channel without checking
for the HT capabilities. (we should have NL80211_CHAN_NO_HT in our
case because the firmware did not support HT)
This patch adds a check on ht_cap.ht_supported in order to create the
channel corresponding to the firmware capabilities.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When enabling WLAN tethering, a new AP is visible and a STA could
connect to it. When the STA tries to authenticate to the newly created
AP, the WPA authentication mechanism is stuck in the 1/4 msg of 4-Way
Handshake.
In ath6kl_rx(), the ath6kl_find_sta() function is looking for the
h_source field of the Ethernet frame header received by the STA. The
datap pointer that points to the Ethernet frame header is incorrect,
and was pointing at the wrong offset in the buffer.
This commit adds a pad_before_data_start offset to set the datap pointer
to the Ethernet frame header. datap->h_source parameter is now really
pointing to the source ethernet address and the authentication process
can continue.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ideally wake_tx_queue should be used regardless as
it is a requirement for reducing bufferbloat and
implementing airtime fairness in the future.
However some setups (typically low-end platforms
hosting QCA988X) suffer performance regressions
with the current wake_tx_queue implementation.
Therefore disable it unless it is really
beneficial with current codebase (which is when
firmware supports smart pull-push tx scheduling).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Same skb is being reused for storing command response from firmware
in PCIe chipsets. There was a bug while updating the skb length.
This patch ensures skb length correctly gets updated based on rx_len.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In corner case, we may end up processing same interrupt twice.
We have a logic to read pending interrupts at the end of interrupt
processing routine. It has a race with interrupts read in interrupt
handler. This patch solves the problem by ORing the interrupt bitmap
in this case.
The symptom for this bug is below messages in dmesg log.
[ 11.522123] mwifiex_pcie 0000:01:00.0: CMD_RESP: invalid cmd resp
[ 11.680412] mwifiex_pcie 0000:01:00.0: There is no command but got cmdrsp
Link: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that request_irq() failure leads to a system crash
due to a bug in mwifiex driver.
When this failure happens, mwifiex_add_card() already takes care of
clearing and freeing adapter->card pointer. This patch removes the
redundant cleanup code causing crash.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The sdio dpc starts processing when in SDIOD_STATE_DATA. This state was
entered right after firmware download. This patch moves that transition
just before enabling sdio interrupt handling thus avoiding watchdog
expiry which would put the bus to sleep while probing.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the host-interface bus has hard time handling transmit packets
it informs higher layer about this and it would stop the netdev
queue when needed. However, since commit 9cd18359d3 ("brcmfmac:
Make FWS queueing configurable.") this was broken. With this patch
the behaviour is restored.
Cc: stable@vger.kernel.org # v4.5, v4.6, v4.7
Fixes: 9cd18359d3 ("brcmfmac: Make FWS queueing configurable.")
Tested-by: Per Förlin <per.forlin@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
memory is malloced in mwifiex_cfg80211_start_ap() and should be
freed before leaving from the error handling cases, otherwise it
will cause memory leak.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes the following sparse warning:
drivers/net/wireless/marvell/libertas/cfg.c:2047:5: warning:
symbol 'lbs_set_power_mgmt' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adding this opcode, allows the TI wireless driver,
to report throughput directly from FW to mac80211.
This is used mainly for mesh metric calculation.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[kvalo@codeaurora.org: fix indentation]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW will provide a TX rate per link for each FW status,
and wlcore will be able to store the information for
the use of the mesh hwmp module.
This is used mainly in mesh.
Rates are reported when a mesh interface is up.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was succesfully tested with 4366B1. A small workaround is needed
for the main interface otherwise it would stuck at the hidden state.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1. Added support for interface and role of mesh type.
2. Enabled enable/start of mesh-point role,
and opening and closing a connection with a mesh peer.
3. Added multirole combination of mesh and ap
under the same limits of dual ap mode.
4. Add support for 'sta_rc_update' opcode for mesh IF.
The 'sta_rc_update' opcode is being used in mesh_plink.c.
Add support in wlcore to handle this opcode correctly for mesh
(as opposed to current implementation that handles STA only).
5. Bumped the firmware version to support new Mesh functionality
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For multiple REG Host Commands (e.g HostCmd_CMD_802_11_EEPROM_ACCESS,
HostCmd_CMD_MAC_REG_ACCESS etc.) "cpu_to_leX"-converted values are
saved to driver. So, "leX_to_cpu" conversion is required too many
times afterwards in driver.
This patch reduces the endian: conversion without saving "cpu_to_leX"
converted values in driver. This will convert endianness in prepare
command and command response path.
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Major changes:
iwlwifi
* more work on the RX path for the 9000 device series
* some more dynamic queue allocation work
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
mwifiex
* implement get_tx_power and get_antenna cfg80211 operation callbacks
wl18xx
* add support for 64bit clock
rtl8xxxu
* aggregation support (optional for now)
Also wireless-drivers is merged to fix some conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXhmR1AAoJEG4XJFUm622bn+gH/Ar5l/oU76nmXKh0xNiV6bUE
2FuRV9X7ynAOLbFJfqZvN8eL1kTyztXOpxVOt9xLZvNcrJP2mdOH+YdUpSPk/XRw
mpFC7RCln/Y1bbX02la7V8iRJlKK1/VmdMABJXsalDcxSPMhhBQtr4/ZC7NcgmeJ
zKCZDGr/x4qpmAkYGsf3msJsBotHtt9xuHp4fFswp9Gpm+VeqtdqGEeMxowoILRK
QBj6nZIuLI4PMnJhfCJn94t9D/AVUIVJTeuWNDS5Up4gZVFo9SlpnkR520P0IY4Q
1238g5sAdKqONsPO0lyUacUlY2cTafDr4kD6UKnjf659KDd49MDJArpfbvMeweY=
=PTV+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.8
Major changes:
iwlwifi
* more work on the RX path for the 9000 device series
* some more dynamic queue allocation work
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
mwifiex
* implement get_tx_power and get_antenna cfg80211 operation callbacks
wl18xx
* add support for 64bit clock
rtl8xxxu
* aggregation support (optional for now)
Also wireless-drivers is merged to fix some conflicts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The iwl-debug.h header relies in implicit inclusion of linux/device.h and
we get a lot of warnings without that:
drivers/net/wireless/intel/iwlwifi/iwl-debug.h:44:23: error: 'struct device' declared inside parameter list will not be visible outside of this definition or declaration [-Werror]
void __iwl_err(struct device *dev, bool rfkill_prefix, bool only_trace,
^~~~~~
In file included from drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.h:66:0,
from drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.c:68:
drivers/net/wireless/intel/iwlwifi/iwl-trans.h: In function 'iwl_trans_tx':
drivers/net/wireless/intel/iwlwifi/iwl-trans.h:1030:348: error: passing argument 1 of '__iwl_err' from incompatible pointer type [-Werror=incompatible-pointer-types]
IWL_ERR(trans, "%s bad state = %d\n", __func__, trans->state);
^
In file included from drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.c:67:0:
drivers/net/wireless/intel/iwlwifi/iwl-debug.h:44:6: note: expected 'struct device *' but argument is of type 'struct device *'
void __iwl_err(struct device *dev, bool rfkill_prefix, bool only_trace,
^~~~~~~~~
The easiest workaround is to just declare 'struct device' before its first use,
rather than including the entire header file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 21cb3222fe ("iwlwifi: decouple PCIe transport from mac80211")
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As hw cycle counters in QCA4019 wraparound independantly in QCA4019
it is possible cycle counter and rx clear counter would wraparound
at the same time. Current logic assumes only one of the counters
would wraparound at anytime. Fix this by moving 'else' part to
another 'if'.
Fixes: 8e100354a9 ("ath10k: fix cycle counter wraparound handling for QCA4019")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes the firmware sends a HAL_DEL_BA_IND, the prima driver silently
ignore this message so let's do the same to silence the error message.
Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch fixes some issues with interface reconfiguration. It could
for example happen that an AP interface in beacon slot 0 was removed
leaving an IBSS station in one of the other slots. When this happens
the driver never sends out the beacon as it only tries to send a beacon
from slot 0.
Appart from that the tracking of required changes to the beacon config is
relatively complicated and prone to errors.
The approach taken here is to solve reconfiguration issues is to
reconfigure the beacons when any interface changes. This means that
the complexity of deciding whether an interface change may modify the
beacon configuration is gone. It also means that the beacon config will
be reliably updated when an interface is removed.
The issue that a single non-AP interface might not be in beacon
slot 0 and wouldn't be send out is solved by moving it into the
first slot. The TSF value in hardware is adjusted accordingly so
that the timestamp of the beacons stay consistent.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The removed ATH9K_SLOT_TIME_X constants simply map the value in microseconds
to the same integer. These constants were not used consistently, so fix the
inconsistency issue by replacing all occurances with the integer equivalent.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath9k driver modifies the TSF for VIFs for the purpose of sending
beacons in a staggered fashion. This patch exposes this VIF specific
adjustment of the TSF value to mac80211. Without the change the TSF
routines handle the hardware TSF value instead of the actual TSF value as
seen on the air.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These changes make ath9k_hw_reset more consistent with other places that
handle the TSF value by using the same helper routine.
A slight improvement is to not assume that a fixed time of 1.5ms has
passed for the initval writes when compared to the first write attempt.
Instead the TSF value is re-calculated which will yield a higher accuracy
of the restored TSF timer.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath9k TSF handling routines need to be aware of the channel context that
is being modified. With this change the TSF related values that are stored
in each channel context will be correctly tracked and the harware will only
be updated if the modified context is currently the active one.
Without this change the TSF modifications done using these routines would
for example be lost during a hardware reset as done by ath_complete_reset.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Beacons were not send out at (timestamp % beacon_time == 0) for interfaces
other than the primary one. To send out beacons with the correct timestamp
according to 10.1.3.2 of the 802.11 standard the tsf_adjustment has to be
set to the negative time difference instead of positive. This way the
later beacons get corrected to have a lower (and similar) timestamp with
regard to the beacon from slot 0.
I am not aware about any issues that have been caused by this.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functional changes, this simply makes the code easier to understand
because all initialization based on ath9k_platform_data is now within
one function.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath9k_hw_init_macaddr unconditionally returns 0 in all cases, making the
return value unnecessary.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently setting the MAC address via ath9k_platform_data works only due
to the order in which init.c sets common->macaddr, which is done after
ath9k_hw_init_macaddr was executed. It would be better if the latter
was independent of the order in which it's being called.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functional changes - this only removes a variable which is set but
never read.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some devices running OpenWrt need this and it makes sense to add this
to ath9k_platform_data as the next patches will add a devicetree
(boolean) property for it as well.
Suggested-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix up the wcn36xx_smd_update_scan_params() to work with non-ancient
versions of the firmware and support actually specifying the list of
channels.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The CCU block in WCNSS is configured for appropriate routing of
interrupts from the DXE to the application cpu, this is not dependant on
the iris version (wcn3660 vs wcn3680), but rather if the SoC has a riva
or pronto built in.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Split the wcnss mmio space into explicit regions for ccu and dxe and
acquire these from the node referenced by the qcom,mmio phandle.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation for handling incoming messages from IRQ context, change
the indication list lock to a spinlock
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Merge the two allocation instead of separately allocating room for the
indication payload.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This driver contains some complicated if ... else if ... else constructions.
These are replaced by switch statements to improve readability.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8192DE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8821AE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8723BE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8723AE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8192EE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8188EE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8192CU chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8192CE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All of the rtlwifi family of drivers have a similar routine that acquires
the hardware info from efuse and initializes a number of variables in the
driver's private area. A common routine is created for all drivers to use.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As interrupt is read in interrupt handler as well as interrupt processing
thread, we observed a corner case issue for MSI in which interrupt gets
processed twice.
This patch moves interrupt reading code for MSI mode from
mwifiex_interrupt_status() to mwifiex_pcie_process_int() to avoid the
issue.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The PCIe driver didn't mask the host interrupts before trying to tear
down. This causes lockups at reboot or rmmod when using MSI-X on 8997,
since the MSI handler gets confused and locks up the system.
Also tested on 8897, which does not support MSI-X (and wasn't
experiencing this same bug). No regressions seen there.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PCIe-USB8997 variant is being used in the product. Let's change default
firmware from PCIe-UART to PCIe-USB. So by default PCIe-USB firmware would
be downloaded if version register doesn't give any information.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The two members min_scan_time and max_scan_time of structure
"mwifiex_ie_types_btcoex_scan_time" are of two bytes each. The values
are assigned directtly from firmware without endian conversion handling.
So, wrong datas will get saved in big-endian systems.
This patch converts the values into cpu's byte order before assigning them
into the local members.
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New firmwares (e.g. 10.10.69.36 for BCM4366) support "interface_remove"
for removing interfaces. Try to use this method on cfg80211 request. In
case of older firmwares (e.g. 7.35.177.56 for BCM43602 as I tested) this
will just result in firmware rejecting command and this won't change any
behavior.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far when receiving event about in-firmware-interface removal our
event worker was notifying listener and afterwards it was removing Linux
interface.
First of all it was resulting in slightly unexpected order. The listener
(del_virtual_intf callback) was (usually) returning with success before
we even called unregister_netdev(ice).
Please note this couldn't be simply fixed by changing order of calls in
brcmf_fweh_handle_if_event as unregistering interface earlier could free
struct brcmf_if.
Another problem of current implementation are possible lockups. Focus on
the time slot between calling event handler and removing Linux
interface. During that time original caller may leave (unlocking rtnl
semaphore) *and* another call to the same code may be done (locking it
again). If that happens our event handler will stuck at removing Linux
interface, it won't handle another event and will block process holding
rtnl lock.
This can be simply solved by unregistering interface in a proper
callback, right after receiving confirmation event from firmware. This
only required modifying worker to don't unregister on its own if there
is someone waiting for the event.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
scan_block flag is used to block scan operation when 4 way handshake
is in progress. Sometimes it doesn't get cleared due to incomplete
association. An example is assoc request/response is done, but add key
operation get canceled in some corner cases. As a result, further
association/scan operations are blocked.
This patch fixes the problem by clearing scan_block flag.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fix spelling typos found in drivers/net/wireless/realtek.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This allows the user to specify DMA aggregation timout and block
count. Blocks are presumably always 512 bytes, so the minimum block
count is 6 for 802.11 packets.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gen2 chips as well as 8188eu seems to use this register for setting
DMA timeout threshold values, however the 8192cu is using
REG_USB_DMA_AGG_TO. Set both to be on the safe side.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Let the default to off until we have more data on the right default
tuning values.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This enables aggregation on rtl8192cu and derivative parts. This uses
the same parameters as for rtl8723au.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement rtl8xxxu_gen1_init_aggregation(). Aggregation should be the
same for all gen1 parts. We may want to allow for tuning parameters in
the fileopes struct. For now this is based allocating 16KB RX buffers,
leaving 16000 bytes for actual packets, and the rest for the skb
overhead.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The old allocation didn't leave space for phystats in the buffer,
allowing the packet to be rejected if a frame size of size
IEEE80211_MAX_FRAME_LEN was received.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This adds support for allocating larger skbs for devices which
indicate they support it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This implements support for demuxing aggregated RX packets on gen1
devices, using the rxdesc16 format.
So far this has only been tested with rtl8723au devices.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This corrects the definition of rxdesc16 to correctly specify pkt_cnt
for aggregated packets. This is based on the code of the vendor
rtl8723au driver, as opposed to the struct definitions they use.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When handling aggregated packets, we'll get a new ieee80211_rx_status
for each cloned skb, so passing in the pointer from the outside
doesn't make sense.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is another prepatory patch to be able to handle aggregated RX
packets.
In order to avoid adding a prototype, this also moves the
rtl8723bu_handle_c2h() function.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This needs to be handled locally in the parse_rx_desc() function in
order to be able to handle aggregated packets in the future.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Changed the configuration to support 64bit instead of 32bit
this in order to offload the driver from handling a wraparound.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The flag should be cleaned along with other scan operation variables.
This was missing at some places.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will derive sta_priv at the beginning of suspend handler.
This will be useful for next patch in this series.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RT_TRACE does not add a newline to the end of a message and always
emits at KERN_DEBUG so these are susceptible to message interleaving
from other processes without the newline.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This debugging macro can expand to a lot of code.
Make it a function to reduce code size.
(x86-64 defconfig w/ all rtlwifi drivers and allyesconfig)
$ size drivers/net/wireless/realtek/rtlwifi/built-in.o*
text data bss dec hex filename
900083 200499 1907 1102489 10d299 drivers/net/wireless/realtek/rtlwifi/built-in.o.defconfig.new
1113597 200499 1907 1316003 1414a3 drivers/net/wireless/realtek/rtlwifi/built-in.o.defconfig.old
1746879 453503 8512 2208894 21b47e drivers/net/wireless/realtek/rtlwifi/built-in.o.new
2051965 503311 8512 2563788 271ecc drivers/net/wireless/realtek/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
USB urbs will return with a status != 0 when rmmod'ing the driver. No
need to fill the log with messages from rtl8xxxu_int_complete()
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
reg_eac and reg_ecc are only used if candidate is bigger than 0, and in
that case new values will be given to them. Removing the unused
assignments.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
* general cleanups
* general bugfixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PpSg
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* work on DQA continued
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
* general cleanups
* general bugfixes
Print an ath10k error message rather a call trace when HTT op version is
not found from firmware META data (IE). This should be sufficient to figure
out what went wrong.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9888 shares the same configuration with QCA99X0
with NSS=2.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
rtc_state_cold_reset_mask is unused in ath10k_hw_regs.
instead fixed delays are used.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If WMI and/or firmware has issues removing the peer object,
then we still need to clean up the peer object in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Not sure this can happen, but seems like a reasonable sanity
check.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
just to comply to coding style.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is expected that all pktlog events for 10.4 firmware based solutions
should come through CE8 where as in case of 10.2 firmware based solutions,
it should come through one of the HTT events (HTT_T2H_MSG_TYPE_PKTLOG).
But from experiments with 10.4 based solutions, it is observed that pktlog
event for ATH_PKTLOG_TYPE_TX_MSDU_ID is coming through HTT pktlog event.
Currently, we always parse with 10.2 pktlog header which will lead to
pktlog decoding issues (payload length mismatch exceptions)
For trace points, it is required to provide only the payload size. So
fixing this by simplifying the payload size calculation without the use of
ath10k pktlog headers.
While there, remove the unused ath10k pktlog headers.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
<linux/semaphore.h> is not used anymore, so just remove the include.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While debugging OS crashes due to firmware crashes, I enabled
kasan, and it noticed that peer objects were being used-after-freed.
Looks like there are two places we could be leaving stale references
in the peer-map, so clean that up.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Otherwise, the txrx-compl-task may access some bad memory?
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211/nl80211 interface changes for per STA total rx-duration and
very basic 'ath10k_sta_statistics' mac80211 callback is implemented
to extend support for per station statistics from the driver.
Also provision in 'iw dev wlan#N station dump' to parse rx-duration
is supported. So its safer to remove the debugfs entry for per STA
rx-duration
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable support for 'drv_sta_statistics' callback.
Export rx_duration support if available to cfg80211/nl80211
This can also act as a placeholder for any new per STA stats support
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 'extended peer stats' will be not be appended with normal peer stats
data and they shall be coming in separate chunks. Fix this by maintaining
a separate linked list 'extender peer stats' for 10.4 and update
rx_duration for per station statistics. Also parse through beacon filter
(if enabled), to make sure we parse the extended peer stats properly.
This issue was exposed when more than one client is connected and
extended peer stats for 10.4 is enabled
The order for the stats is as below
S - standard peer stats, E- extended peer stats, B - beacon filter stats
{S1, S2, S3..} -> {B1, B2, B3..}(if available) -> {E1, E2, E3..}
Fixes: f9575793d4 ("ath10k: enable parsing per station rx duration for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add radar_detect_widths to the interface combination that allows
concurrent P2P Device dedicated interface and AP interfaces, to enable
testing of radar detection when P2P Device interface is used.
Clear the radar_detect_widths in case of multi channel contexts
as this is not currently supported.
As radar_detect_widths are now supported in all combinations,
remove the hwsim_if_dfs_limits definition since it is no longer
needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All transports has this structure. By moving it to be
shared, we can get rid of casting to the specific transport
in probe and remove.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Centralize the logging of SCD status. The motivation is
that for a000 devices we will have new SCD HW, but this
code was duplicate anyway, so it is a proper cleanup.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for the v4 version of the TX power command. Just add a
new version and do the same sizing tricks that were done when support
for v3 was introduced.
This patch doesn't support the new functionality introduced, but makes
the driver work with the new size of the command.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For a000 device the FH was replaced by the TFH.
This is the first patch in a series introducing the
changes stemming from this change.
This patch initializes the TFQ queue table with the new
64 bit register and the relevant TFH configuration
registers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the write_prph_64 of pcie to be transport agnostic.
Add direct write as well, as it is needed for a000 HW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the scratch buffer is set to 16 bytes and indicates
the size of the bi-directional DMA.
However, next HW generation will perform additional offloading,
and will write the result in the key location of the TX command,
so the size of the bi-directional consistent memory should grow
accordingly - increase it to 40.
Generalize the code to get rid of now irrelevant scratch references.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In MQ environment and new architecture in early stages
we may encounter DMA issues. Track RXB status and bail
out in case we receive index to an RXB that was not
mapped and handed over to HW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Upon firmware load interrupt (FH_TX), the ISR re-enables the
firmware load interrupt only to avoid races with other
flows as described in the commit below. When the firmware
is completely loaded, the thread that is loading the
firmware will enable all the interrupts to make sure that
the driver gets the ALIVE interrupt.
The problem with that is that the thread that is loading
the firmware is actually racing against the ISR and we can
get to the following situation:
CPU0 CPU1
iwl_pcie_load_given_ucode
...
iwl_pcie_load_firmware_chunk
wait_for_interrupt
<interrupt>
ISR handles CSR_INT_BIT_FH_TX
ISR wakes up the thread on CPU0
/* enable all the interrupts
* to get the ALIVE interrupt
*/
iwl_enable_interrupts
ISR re-enables CSR_INT_BIT_FH_TX only
/* start the firmware */
iwl_write32(trans, CSR_RESET, 0);
BUG! ALIVE interrupt will never arrive since it has been
masked by CPU1.
In order to fix that, change the ISR to first check if
STATUS_INT_ENABLED is set. If so, re-enable all the
interrupts. If STATUS_INT_ENABLED is clear, then we can
check what specific interrupt happened and re-enable only
that specific interrupt (RFKILL or FH_TX).
All the credit for the analysis goes to Kirtika who did the
actual debugging work.
Cc: <stable@vger.kernel.org> [4.5+]
Fixes: a6bd005fe9 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The PCIe transport needs to store two pointers in each TX SKB, and
currently assumes mac80211's ieee80211_tx_info is present in the CB
to do that.
In order to remove that assumption, have the opmodes pass in the
offset to where the pointers can be stored in the CB and use the
offset in the PCIe code.
To make the disentanglement complete, remove mac80211.h includes
from everywhere in the generic iwlwifi code. This required adding
an include of cfg80211.h in one place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to properly record SKBs that didn't come through
mac80211, don't rely on the IEEE80211_TX_CTRL_PORT_CTRL_PROTO flag
but instead check for ETH_P_PAE directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to reduce reliance on mac80211 structs in the core
iwlwifi code, store the cipher schemes in the format given
by the firmware and convert it later, rather than storing it
in the mac80211 format.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Restart flow zeroes the rx_ba_sessions counter. Mac80211 asks
driver to tear down of the session only afterwards, and as a
result driver didn't free the data. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 10b2b2019d ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make sure that in DQA mode, the SCD's configuration of a
queue is redirected to the lower AC of the streams of the
queue.
Make sure that this queue is redirected to the lowest AC
when adding a new RA/TID to an existing queue. If it isn't -
redirect the queue.
Also, as redirection revealed a bug in the marking of a
shared queue, this patch contains a small fix to make
sure a shared queue maintains the appropriate "shared queue
marking".
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support TDLS when working in DQA mode.
This is done mainly by NOT doing any special things
for TDLS, as the queues are dynamically created anyway,
so no need to allocate them ahead of time.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In cases of hardware or DMA error, the vid read from
a zeroed location will be 0, and we will access the rxb
at index 0 in the global table, while it may be NULL or
owned by hardware.
Invalidate vid 0 in order to detect the situation and
bail out.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This led to a DMA splat.
Fixes: a6c4fb4441 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This struct member is never set, so remove it.
Since this is the last thing that needs mac80211.h, also change
the includes to no longer use mac80211.h
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value for Channel 14 was wrong. Fix it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The TX fifos are arranged consecutively in the SMEM, beginning
with the regular fifos, and tailed by the internal fifos.
In the current code, while trying to read the internal fifos,
we read the fifos beginning with the index zero.
By doing this we actually re-read the regular fifos.
In order to read the internal fifos, start the reading index
from the number of regular fifos configured by the fw.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Fixes: 39654cb3a6 ("iwlwifi: don't access a nonexistent register upon assert")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This fixes a pretty ancient bug that hasn't manifested itself
until now.
The scratchbuf for command queue is allocated only for 32 slots
but is accessed with the queue write pointer - which can be
up to 256.
Since the scratch buf size was 16 and there are up to 256 TFDs
we never passed a page boundary when accessing the scratch buffer,
but when attempting to increase the size of the scratch buffer a
panic was quick to follow when trying to access the address resulted
in a page boundary.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 38c0f334b3 ("iwlwifi: use coherent DMA memory for command header")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On some of the chipsets MSI & INTA interrupts are disabled by default in
the HW registers, and need to be explicitly enabled to be used.
In case MSI-X isn't used, make sure MSI mode is enabled by setting
the relevant HW register.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Read the SAR BIOS table from the ACPI and parse it into the
iwl_mvm_sar_table structure. If the table is enabled, send it to the
firmware via REDUCE_TX_POWER_CMD.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We removed support for old API for coexistence, but we
forgot to remove defines and variable that are not needed
anymore.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our HW does not support checksum of fragmented packets.
Fix code accordingly to checksum those packets in the driver.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the state sent in SF configuration is always
FULL_ON.
This commit sets the correct state (e.g. INIT_OFF
when station is not associated).
Fixes: commit f4a3ee493e ("iwlwifi: mvm: Always enable the smart FIFO")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The NIC's CPU gets started after the firmware has been
written to its memory. The first thing it does is to
send an interrupt to let the driver know that it is
running. In order to get that interrupt, the driver needs
to make sure it is not masked. Of course, the interrupt
needs to be enabled in the driver before the CPU starts to
run.
I mistakenly inversed those two steps leading to races
which prevented the driver from getting the alive interrupt
from the firmware.
Fix that.
Cc: <stable@vger.kernel.org> [4.5+]
Fixes: a6bd005fe9 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For 9000 family we will get extended statistics notification
with averaged data for RSSI, TCM and rogue AP detection.
Support it. Future patches will added the required algorithms.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer hardware supports GCMP and GCMP 256-bit ciphers.
Add support for adding/setting GCMP key for TX mode.
In the TX command handling GCMP-256 is handled in a different
way as the key size should be up to 128-bits:
Set the key value to the key index in the key table,
and specify that this key should be taken form the key table
instead of from the TX command.
While at it - convert security control flags to an enum.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support of dumping new RFH instead of FH registers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
gcc-6 reports the following error if -Werror=unused-const-variable
is enabled.
drivers/net/wireless/intel/iwlwifi/dvm/lib.c:210:21: error:
'iwlagn_loose_lookup' defined but not used
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix an issue where nullfunc frames and block ack requests
had the same tid as aggregation frames and were queued on
a non aggregation queue. The pending frames counter included
those frames but the check whether to decrement the pending
frames counter relied on the tid status and not on the txq id.
The result was an inconsistent state of the pending frames
counter followed by a failure to remove the station.
This failure triggered SYSASSERT 0x3421.
In addition, fix a situation in DQA mode where the number
of pending frames turned negative. This was due to the TX queue
being on the IWL_EMPTYING_HW_QUEUE_DELBA state and its frames
were still decremented.
Even though the SYSASSERT issue is fixed when DQA is disabled,
the issue is not completely solved when DQA is enabled and
should still be fixed.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
gcc is apparently unablel to track the state of the local 'resp_v2'
variable across the kzalloc() function, and warns about the response
variable being used without an initialization:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c: In function ‘iwl_mvm_update_mcc’:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:727:36: warning: ‘mcc_resp_v1’ may be used uninitialized in this function [-Wmaybe-uninitialized]
resp_cp->n_channels = mcc_resp_v1->n_channels;
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:721:3: warning: ‘mcc_resp’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(resp_cp, mcc_resp, resp_len);
The warning showed up in x86 allmodconfig after my patch to
unhide -Wmaybe-uninitialized warnings by default was merged,
though it always existed in randconfig builds. I did not
catch the warning earlier because I was testing on ARM, which
never produced the warning.
This rearranges the code in a way that improves readability for
both humans and the compiler, and that avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6fa52430f0 ("iwlwifi: mvm: change mcc update API")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Expand TLC to support 160MHz channels. Full support for A-MSDU
case will be added separately.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW sets status for each RX packet.
Enum in the driver doesn't match with FW definition - fix it.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we try to open an aggregation for every packet (given that one
is not already open).
This causes redundant overhead (addba/delba) for null data packets.
Do not open an aggregation for null data packets.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Somehow we ended up stopping RX using legacy RX registers
even for devices that support RFH. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We convert the mvm device to a PCI device and then back again when
trying to find the handle for the device's ACPI data. This is
unnecessary, so it can be removed.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support sending the DQA-enablement HCMD to the FW when
working in DQA mode.
This HCMD will enable DQA-specific flows in the FW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the AUX queue is mapped elsewhere than in non-
DQA mode. Update the code to reflect this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the correct sta_id in the SCD_QUEUE_CONFIG command sent
to the FW when enabling/disabling queues. This is needed in
DQA-mode to allow the FW to associate between queue and STA.
In case the queue isn't connected to a specific station but
rather is a static "generic" queue - the sta_id should be
set to 0x10 (max supported STA is 0x0f).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support DQA queue sharing when no free queue exists for
allocation to a STA that already exists. This means that
a single queue will serve more than a single TID (although
the RA will be the same for all TIDs served).
We try to choose the lowest AC possible, to ensure the
shared queues have the lowest possible combined AC
requirements. The queue to share is chosen only from the
same RA's DATA queues as follows (in descending priority):
1. An AC_BE queue
2. Same AC queue
3. Highest AC queue that is lower than new AC
4. Any existing AC (there always is at least 1 DATA queue)
If any aggregations existed for any of the TIDs of the
shared queue - they are stopped (the FW is notified), but
no delBA is sent.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
"max_amsdu_len" isn't set if kstrtouint() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We never initialize ampdu_status so it causes a static checker warning
when we pass it to iwl_mvm_pass_packet_to_mac80211(). Fortunately, it's
never used so we can just remove it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some transports may sleep when writing to registers, which is done
when calling iwl_force_nmi(). So we can't call iwl_force_nmi() in a
timer context. To solve that, convert the scan timeout timer to a
delayed work.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Theoretically we may get only one IRQ from OS, in which
case we will have only 1 queue even in MSIx mode.
This will cause division by zero in the indirection table
calculation.
We do not need send the command in that case, as there is
only one queue so all RX traffic will be directed to it
anyway. Bail out early if there is only one queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently code calls restock for mq devices during the init
function, unlike sq where restock is called after init.
This causes an harmless but alarming deadlock warning from
lockdep, to fix this - unify the init code.
Rename the restock functions while at it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support marking queues as inactive upon a timeout expiring,
and allow inactive queues to be re-assigned to other RA/TIDs
if no other queue is free.
This is done by keeping a timestamp of the latest frame TXed
for every RA/TID, and then going over the queues currently in
use when a new queue is needed, inactivating all those that
are inactive.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of explicitly indicating the difference between just
DVM and MVM with an mvm_fw boolean change this to fw.type to
be more extensible and easier to understand.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the values of this enum are used only internally,
we can let the compiler number them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Flag rfchange_inprogress in struct rtl_ps_ctl is protected by a spinlock
in most routines but not in rtl8821ae_dm_watchdog() which could
lead to a race condition. The necessary locking to prevent this condition
is added.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Flag rfchange_inprogress in struct rtl_ps_ctl is protected by a spinlock
in most routines but not in rtl8723e_dm_watchdog(), which could
lead to a race condition. The necessary locking to prevent this condition
is added.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Flag rfchange_inprogress in struct rtl_ps_ctl is protected by a spinlock
in most routines but not in rtl8723be_dm_watchdog(), which could
lead to a race condition. The necessary locking to prevent this condition
is added.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Flag rfchange_inprogress in struct rtl_ps_ctl is protected by a spinlock
in most routines but not in rtl92ee_dm_watchdog(), which could
lead to a race condition. The necessary locking to prevent this condition
is added.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Flag rfchange_inprogress in struct rtl_ps_ctl is protected by a spinlock
in most routines but not in rtl88e_dm_watchdog(), which could
lead to a race condition. The necessary locking to prevent this condition
is added.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 4b9d8d67b4 ("rtlwifi: rtl8192cu: Remove unused parameter") reworked
this routine. Those changes were later reverted by commit d3feae41a3
("rtlwifi: Update power-save routines for 062814 driver").
There were two changes in commit 4b9d8d67b4. The first of these removed
a parameter from rtl_ps_set_rf_state() that was always false. This is the
change that is restored in the current patch. A second change that reworked
the locking is still being analyzed.
In addition to removing the unused parameter, there is no need for
rtl_ps_set_rf_state() to be exported.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes MSIx interrupts are received out of order on multi-core
system. This creates a problem when there is a race between data
packet and SLEEP event from firmware. We will disable MSIx interrupt
mode to solve the problem and go with MSI mode.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit de3bb771f4 ("cfg80211: add more warnings for inconsistent
ops") the wireless core warns if a driver implements a cfg80211 callback
but doesn't implements the inverse operation.
The mwifiex driver defines a .set_antenna handler but not a .get_antenna
so this not only makes the core to print a warning when creating a new
wiphy but also the antenna isn't reported to user-space apps such as iw.
This patch queries the antenna to the firmware so is properly reported to
user-space. With this patch, the wireless core does not warn anymore and:
$ iw phy phy0 info | grep Antennas
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
[javier: expand the commit message]
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The mwifiex driver implements a cfg80211 .set_tx_power operation handler
but doesn't have the inverse .get_tx_power callback.
This not only has the effect that the Tx power can't be reported to user
space tools such as iwconfig and iwlist but also that the wireless core
prints a warning when a new wiphy is created due an cfg80211 operation
being implemented without its counterpart.
After this patch, the Tx power is properly reported to user-space tools:
$ iwlist mlan0 txpower
mlan0 unknown transmit-power information.
Current Tx-Power=13 dBm (19 mW)
and also the following warning isn't shown anymore on the driver probe:
WARNING: CPU: 3 PID: 127 at net/wireless/core.c:366 wiphy_new_nm+0x66c/0x6ac
Modules linked in: mwifiex_sdio mwifiex
CPU: 3 PID: 127 Comm: kworker/3:1 Tainted: G W 4.7.0-rc1-next-20160531-00006-g569df5b983f3
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events request_firmware_work_func
[<c010e1ac>] (unwind_backtrace) from [<c010af38>] (show_stack+0x10/0x14)
[<c010af38>] (show_stack) from [<c0323b9c>] (dump_stack+0x88/0x9c)
[<c0323b9c>] (dump_stack) from [<c011a828>] (__warn+0xe8/0x100)
[<c011a828>] (__warn) from [<c011a8f0>] (warn_slowpath_null+0x20/0x28)
[<c011a8f0>] (warn_slowpath_null) from [<c06a42d4>] (wiphy_new_nm+0x66c/0x6ac)
[<c06a42d4>] (wiphy_new_nm) from [<bf1c24cc>] (mwifiex_register_cfg80211+0x28/0x3f0 [mwifiex])
[<bf1c24cc>] (mwifiex_register_cfg80211 [mwifiex]) from [<bf1a0018>] (mwifiex_fw_dpc+0x2b0/0x474 [mwifiex])
[<bf1a0018>] (mwifiex_fw_dpc [mwifiex]) from [<c040eb74>] (request_firmware_work_func+0x30/0x58)
[<c040eb74>] (request_firmware_work_func) from [<c012fe90>] (process_one_work+0x124/0x338)
[<c012fe90>] (process_one_work) from [<c01300dc>] (worker_thread+0x38/0x4d4)
[<c01300dc>] (worker_thread) from [<c01353b8>] (kthread+0xdc/0xf4)
[<c01353b8>] (kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The commit 7311ea8500 ("mwifiex: fix AP start problem for newly added
interface") attempted to fix an issue when a new AP interface is added.
But the patch didn't check the return value of the functions doing the
firmware calls and returned an error even if the functions didn't fail.
This prevents the network device to be registered properly, so fix it.
Fixes: 7311ea8500 ("mwifiex: fix AP start problem for newly added interface")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Some more dynamic queue allocation work
* A few bugfixes and other improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXds8vAAoJEKFHnKIaPMX6GNIQAILXaocLMp7DEdzGcw4FLeub
d7EjnuM7NN/daqxdPJFQv1Q044CNt57L1cRIlmoMQQB2jQuHgRPFVWtz4j/2nIl0
h+V6WhBCAgsSSiooRUR4Ck+9Chb3DJBBm85rt1lGXwa0S4QTl21bH2n8zfwp80A4
tXIeTlaxDlnAFmDcDc+QEEjj6ph3Bfu9rgGM3cqHFfYwLfGU6Ny9lnr4HMWOE2JW
QjCKEgF+6eQpzFigHdHIfvjnkSay/LiZ0jNjPzn4Svn5yUHWYx/ldFq72Veyg4L7
ceEQpDWGoEdMMgYue2igf8dFx//9OuQXNdoBCIYs+RY5sGn3gHjRu3GhTiBD5pUN
nLSyGOgwqaXNyF4fumI4CgJwjQmEpa7RCsY+59IAEl/tYZh9kNNrmEfl99k2YruT
5IZeF3D6qjZZs89upxId03bLyEZ4oSLGTbxOq0xOt7GbaE7BIWBRALHe8mNseV+P
4Y3AVks98W1q4iyERpBIMhAWptFt/Tcwt2jGDrFzJHCDBFI5RBLw9NdzEdjxOxsO
GRits9CTARg5R20BSoqcTs1vBC9ymvCvuLcQooRDdLJWbjXURn43rLQ9PTao+lzN
8OJbMz1OzaxIa0QTe3RVPuoTudjlmrAfmAaK2O2LrydSf/7W9g+OZOgn64Z2S5uj
Y5IdAN9cpRHYGbFnbsuQ
=XZrY
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-07-01' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* More work on the RX path for the 9000 device series
* Some more dynamic queue allocation work
* A few bugfixes and other improvements
For some reason, the FRAME_RELEASE message handling for the
default queue ended up being in the only/default queue for
non-RSS devices; fix that and handle FRAME_RELEASE properly
on the default queue for RSS devices.
Fixes: 585a6fccf5 ("iwlwifi: mvm: infrastructure for frame-release message")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support CSA countdown offloading. When CSA starts, the driver
specifies the offsets to the eCSA and CSA IEs in the beacon template
command and the fw performs the countdown.
The fw notifies the driver when the channel switch flow
should be performed.
Beacon sent notifications are not used anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a warning in case packet didn't end up in the HW
destined queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We now have 9000 devices that support multiple frames in
a single RB. Enable it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For 9000 devices we can have PCIe bus for discrete
devices and IOSF bus for integrated devices.
PCIe supports maximum transfer size of 128B while IOSF
bus supports maximum transfer size of 64B.
Configure RB size accordingly.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Integrated 9000 devices have a bug with shadow registers
value retention.
If driver writes RBD registers while MAC is asleep the
values are stored in shadow registers to be copied whenever
MAC wakes up.
However, in 9000 devices a MAC wakeup is not triggered
and when the bus powers down due to inactivity the shadow
values and dirty bits are lost.
Turn on the chicken-bits that cause MAC wakeup for RX-related
values as well when the device is in D0.
When the device is in low power mode turn the RX wakeup chicken
bits off since driver is idle and this W/A is not needed.
Remove previous W/A which was ineffective.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support queue removal in DQA mode in iwl_mvm_rm_sta() also when
the device isn't a STA connected to an AP.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
rx_phy notification is no longer sent in devices with
multiple rx queues.
All the needed data is now set in the metadata - update
code accordingly to reflect all the features as in the
previous RX path.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In multiple RX queues architecture, the RX_PHY notification
is no longer useful as it is received in the default queue
even for packets that are received on RSS queue, and cannot
be accessed without locking.
All the needed data is in the new RX packet metadata and
firmware will no longer send this notification for 9000
devices. Remove support of it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Ucode capability bit 26 indicates support for UAPSD on P2P interface
even with a simultaneous BSS station interface, as long as both
interfaces are in the same binding. Change the name of the
capability bit to reflect that.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Somehow we ended up without leading spaces here, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We cannot trust NSSN for AMSDU sub-frames that are not the
last.
The reason is that NSSN advances on the first sub-frame,
and may cause the reorder buffer to advance before all the
sub-frames arrive.
Example:
Reorder buffer contains SN 0 & 2.
We receive AMSDU with SN 1 and NSSN for first sub frame 3.
The result us that driver releases SN 0,1, 2.
When sub-frame 1 arrives - reorder buffer is already ahead and
it will be dropped.
If the last sub-frame is not on this queue - we will get frame
release notification with up to date NSSN.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new hardware that supports multiple queue also
de-aggregates A-MSDUs. This means that we can advertise
the maximal size of A-MSDUs regardless of the receive
buffer's size.
In order to be able to forcefully use a lower A-MSDU size,
add a default value for the module parameter. Pre-9000
will have a default of 4K, and 9000 will have 12K.
Setting the amsdu_size module parameter to 4K will limit
the A-MSDU on 9000 as well.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The function ar9003_hw_apply_minccapwr_thresh takes as second parameter not
a pointer to the channel but a boolean value describing whether the channel
is 2.4GHz or not. This broke (according to the origin commit) the ETSI
regulatory compliance on 5GHz channels.
Fixes: 3533bf6b15 ("ath9k: Fix regulatory compliance")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Just setting the proper return for reading beyond the eeprom data.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Found this obvious typo while going through the spectral
code design in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Disable TX_STBC for both HT and VHT if the devices tx chainmask is '1'
TX_STBC is required only for devices with tx_chainmask > 1. This fixes
a ping failure for QCA9887 (1x1) in HT/VHT mode
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable beacon loss detection support for 10.4 by handling
roam event. With this change QCA99X0 station is able to
detect beacon loss when the AP is powered off
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Smatch warns about a number of cases in ath10k where a pointer is
null-checked after it has already been dereferenced, in code involving
ath10k private virtual interface pointers.
Fix these by making the dereference happen later.
Addresses the following smatch warnings:
drivers/net/wireless/ath/ath10k/mac.c:3651 ath10k_mac_txq_init() warn: variable dereferenced before check 'txq' (see line 3649)
drivers/net/wireless/ath/ath10k/mac.c:3664 ath10k_mac_txq_unref() warn: variable dereferenced before check 'txq' (see line 3659)
drivers/net/wireless/ath/ath10k/htt_tx.c:70 __ath10k_htt_tx_txq_recalc() warn: variable dereferenced before check 'txq->sta' (see line 52)
drivers/net/wireless/ath/ath10k/htt_tx.c:740 ath10k_htt_tx_get_vdev_id() warn: variable dereferenced before check 'cb->vif' (see line 736)
drivers/net/wireless/ath/ath10k/txrx.c:86 ath10k_txrx_tx_unref() warn: variable dereferenced before check 'txq' (see line 84)
drivers/net/wireless/ath/ath10k/wmi.c:1837 ath10k_wmi_op_gen_mgmt_tx() warn: variable dereferenced before check 'cb->vif' (see line 1825)
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The below warning message seems to hit occasionally with the following
combination (IPQ4019 + ACS scan) where we receive packets as a self peer
when hostapd does ACS when we bring up AP mode . ath10k has the below
fall back mechanism to fetch current operating channel in rx (it will
check for the next channel tracking variable if the current one is NULL)
[scan channel] --> [rx channel] --> [peer channel] -->
[vdev channel] --> [any vdev channel] --> [target oper channel]
'scan channel' and 'target operating channel' are directly fetched from
firmware events. All the others should be updated by mac80211.
During ACS scan we wouldn't have a valid channel context
assigned from mac80211 ('ar->rx_channel'), and also relying on
('ar->scan_channel') is not helpful (it becomes NULL when it goes to
BSS channel and also when the scan event is completed). In short we
cannot always rely on these two channel tracking variables.
'Target Operating Channel' (ar->tgt_oper_chan) seems to keep track of
the current operating even while we are doing ACS scan and etc. Hence
remove this un-necessary warning message and continue with
target_operating channel. At the worst case scenario when the target
operating channel is invalid (NULL) we already have an ath10k warning
message to notify we really don't have a proper channel configured in
rx to update the rx status("no channel configured; ignoring frame(s)!")
WARNING: CPU: 0 PID: 0 at ath/ath10k/htt_rx.c:803
[<c0318838>] (warn_slowpath_null) from [<bf4a0104>]
(ath10k_htt_rx_h_channel+0xe0/0x1b8 [ath10k_core])
[<bf4a0104>] (ath10k_htt_rx_h_channel [ath10k_core]) from
[<bf4a025c>] (ath10k_htt_rx_h_ppdu+0x80/0x288 [ath10k_core])
[<bf4a025c>] (ath10k_htt_rx_h_ppdu [ath10k_core]) from
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task+0x724/0x9d4 [ath10k_core])
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task [ath10k_core])
Fixes:3b0499e9ce42 ("ath10k: reduce warning messages during rx without proper channel context")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Usually when the firmware crashes we check for the value
'FW_IND_EVENT_PENDING' in 'FW_INDICATOR_ADDRESS' and proceed with
disabling the irq and dumping firmware 'crash dump'. Now
when the PCI card is unplugged from the device the PCI controller
seems to generate a spurious interrupt after some time which
was as treated a firmware crash and resulting in the below race
condition (and eventually crashing the system)
ath10k_core_unregister -> ath10k_core_free_board_files
...... device unplug spurious interrupt .........
ath10k_pci_taklet -> ath10k_pci_fw_crashed_dump ...etc
Clearly even after the firmware board files related data structure
is freed up we are getting a spurious interrupt from PCI with 0xfffffff
in the 'FW_INDICATOR_ADDRESS' resulting in scheduling of the pci tasklet
and doing a crash dump, printing f/w board related info resulting in the
below crash. Fix this by detecting this spurious interrupt in ath10k PCI
irq handler itself and return IRQ_NONE. Thanks to Michal Kazior for
helping us conclude the most appropriate fix.
Call trace:
EIP is at ath10k_debug_print_board_info+0x39/0xb0
[ath10k_core]
EAX: 00000000 EBX: d4de15a0 ECX: 00000000 EDX: 00000064
ESI: f615ddd0 EDI: f8530000 EBP: f615de3c ESP: f615ddbc
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000004 CR3: 01c0a000 CR4: 000006f0
Stack:
f615ddd0 00000064 f8b4ecdd 00000000 00000000 00412f4e
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
Call Trace:
[<f8b1f517>] ath10k_print_driver_info+0x17/0x30
[ath10k_core]
[<f875463a>] ath10k_pci_fw_crashed_dump+0x7a/0xe0
[ath10k_pci]
[<f87549d0>] ath10k_pci_tasklet+0x70/0x90 [ath10k_pci]
[<c106151e>] tasklet_action+0x9e/0xb0
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Registering wmediumd is currently limited to the initial network
namespace. This patch enables wmediumd to attach from non-initial
network namespaces using a user namespace having CAP_NET_ADMIN. A
registered wmediumd can forward frames on radios that have been created
in the same network namespace, even if they have been moved to other
network namespaces.
The wmediumd Netlink portid is tracked per net namespace. Additionally,
the portid is stored on all radios created in that net namespace to
simplify the portid lookup in the data path.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Since stations can now be added before association
(NL80211_FEATURE_FULL_AP_CLIENT_STATE support),
no supported rates are set when the station is added
to the fw, resulting in fw recovery.
Fix it by first configuring the AP basic rates as
the station configured rates (when the station is
first added to the driver), and after the station
was authorized re-configure it, now with the actual
supported rates.
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We obviously don't want to fall through in that switch. With this change
1) We wait for event (triggered by p2p_disc) as expected
2) We remove interface manually on timeout
3) We return 0 on success instead of -ENOTSUPP
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This header provides two inline functions using struct brcmf_if so we
need core.h to avoid:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h: In function ‘ndev_to_prof’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:368:13: error: dereferencing pointer to incomplete type
return &ifp->vif->profile;
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h: In function ‘ndev_to_vif’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:374:12: error: dereferencing pointer to incomplete type
return ifp->vif;
^
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function can work just fine with const pointer, it only calls
alloc_netdev which take const as well. Moreover it makes this function
more flexible as some cfg80211 callback may provide const char * as
well, e.g. add_virtual_intf. This will be needed for more advanced
interface management.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removing P2P interface is handled by sending a proper request to the
firmware. On success firmware triggers an event and driver's handler
removes a matching interface.
However on event timeout we remove interface directly from the cfg80211
callback. Current code doesn't handle this case correctly as it always
assumes rtnl to be unlocked.
Fix it by adding an extra rtnl_locked parameter to functions and calling
unregister_netdevice when needed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modern C standards expect the 'inline' keyword to come before the return
type in a declaration, and we get a warning for this with "make W=1":
drivers/net/wireless/intel/ipw2x00/ipw2200.c:4096:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modern C standards expect the 'static' keyword to come first in a
declaration, and we get a warning for this with "make W=1":
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3353:1: error: 'static' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'register' is a keyword in C and cannot be used in place of a
variable name, as shown by this -Wextra warning:
drivers/net/wireless/cisco/airo.c:1105:29: error: 'register' is not at beginning of declaration [-Werror=old-style-declaration]
This replaces the 'register' keyword with a 'reg' identifier in
the declaration, which matches the definition and has the intended
meaning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that if interface type is changed from managed to
__ap, AP can be successfully started. But there is a problem if new
ap interface is added.
The problem got resolved after sending appropriate commands to firmware
in add_interface handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch populates secondary channel offset and downloads it to
firmware to fix the problem.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some platforms, driver is unable to wakeup firmware after system resume
due to a problem at MMC subsystem. Triggering card reset in this case has
a race with card removal from MMC which causes system hang. This patch
resolves the problem by not triggering card reset.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is obeserved that sometimes scan operation will block the disconnect
during system suspend. It's ok to cancel ongoing scan in this case. It
reduces unnecessary system suspend delay.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch creates common function mwifiex_cancel_scan to remove
duplication of code.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When an association command is sent to firmware but the process is
killed before the command response arrives, driver will try to
access bss_desc which is already freed. This issue is fixed by
checking return value of bss_start.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Compiling the rtlwifi drivers for ARM with gcc -Wextra warns about lots of
incorrect code that results from 'char' being unsigned here, e.g.
realtek/rtlwifi/rc.c:113:18: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8188ee/dm.c:1070:22: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192ce/trx.c:54:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192cu/mac.c:601:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192de/trx.c:53:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192ee/phy.c:1268:12: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192se/rf.c:150:20: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8723be/dm.c:877:29: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8723be/phy.c:386:16: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/dm.c:1514:38: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/phy.c:1558:11: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/phy.c:386:24: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/trx.c:55:12: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/stats.c:31:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
This patch changes all uses of 'char' in this driver that refer to
8-bit integers to use 's8' instead, which is signed on all architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
lbs_mac_event_disconnected may free priv->currenttxskb
while lbs_hard_start_xmit accesses to it.
The patch adds a spinlock for mutual exclusion.
Tested on OLPC XO-1 (usb8388) and XO-1.5 (sd8686) with v4.7-rc3.
Confirmed that lbs_mac_event_disconnected is being called on the
station when hostapd on access point is given SIGHUP.
Signed-off-by: Pavel <andrianov@ispras.ru>
Tested-by: James Cameron <quozl@laptop.org>
Acked-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pdev_data pointer is being freed with kfree but the pointer is not dynamic allocated.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use %*ph specifier to dump small buffers in hex format instead of doing this
byte-by-byte.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This also renames REG_USB_AGG_{TO,TH} to REG_USB_AGG_{TIMEOUT,THRESH}
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Documentation for enabling USB aggregation and whether to select
interrupt or bulk delivery of interrupt events.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem (viz
&priv->cmd_work per priv, which maps to lbtf_cmd_work) is involved in
actual command processing and may be used on a memory reclaim path.
The workitems require forward progress under memory pressure and hence,
WQ_MEM_RECLAIM has been set. Since there are only a fixed number of work
items, explicit concurrency limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This change reorders some operations in brcmf_setup_ifmodes in hope to
make it simpler:
1) It allocates arrays right before filling them. This way it's easier
to follow requested array length as it's immediately followed by
code filling it. It's easier to check e.g. why we need 4 entries for
P2P. Other than that it deduplicates some checks (e.g. for P2P).
2) It reorders code to first prepare limits and then define a new combo.
Previously this was mixed (e.g. we were setting num of channels
before preparing limits).
3) It modifies mbss code to use i variable just like other combos do.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
brcmfmac
* add support for the PCIE devices 43525 and 43465
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXaRfMAAoJEG4XJFUm622bxwEH/iZm3o752MM62fJyCOEtEN6R
8vL7kyehX81G9szQyQ7bMQ7y0diobeBGsu8e7zzV4Mt+cU0Z9g/ezfca6HfE6Hrh
0ubKl/tSzAhRcAoQiNyKOI36yt455r1Mnr8a18OYO79pnNcjf7kSd7pJG2BW0Hdx
dRsSxzcg+E0w4z7mJ/cgM5aRzjXmXvAUjw9cIt36y3+ng1fQ+M782lkCtscMZY3Q
e5bkLCaP5TG+O9niPTjzrAzMlBTGwopknuEZnwIGDkNkx1PeBzRATVGeSa9Zba6d
g17kGbP7QT1GaCJF/FfWColaVpMBDhviovQANeoaUi804C4ZKNZAcJirZC3W2eM=
=uYcn
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.8
Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
brcmfmac
* add support for the PCIE devices 43525 and 43465
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi
* fix the scan timeout for long scans
* fix an RCU splat caused when updating the TKIP key
* fix a potential NULL-derefence introduced recently
* fix a IGTK key bug that has existed since the MVM driver was introduced
* fix some fw capabilities checks that got accidentally inverted
rtl8xxxu
* fix typo on variable name
ath10k
* fix deadlock when peer cannot be created
* fix crash related to printing features
* fix deadlock while processing rx_in_ord_ind
ath9k
* fix GPIO mask regression for AR9462 and AR9565
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXaRGeAAoJEG4XJFUm622bc6MH/jBpajTua8/fEUwo8dEywKRD
HULV6h5jDfoQ2N+LkKGff4UoAup4rWvzsXgTsNwPrma+TYi8M/eVrWanJ+TkwI31
2jHh2ynBqAPNhM6oT/NKJgGPgamFsa7mvtM8wBZV4VZseIGhJcKExExLjnE64ZdG
7o6VrtNRNtP+lnxT7ojbcS7cMnQqa7d32CqYjyJtABzLdSHNdww9euHLo9t6EFFa
7dti3t4WftTZ0+VyZmNrLgS+RO0ix7Kbr+ZfNQPyq9DLAaSfNZR8kWpNZjR7G4BA
QYffAkBO/iwffJS9b/VU+o8b32SV0TstTbJsEyvJcqkkTbngj2QhHZHBU012vQk=
=uVoM
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.7
iwlwifi
* fix the scan timeout for long scans
* fix an RCU splat caused when updating the TKIP key
* fix a potential NULL-derefence introduced recently
* fix a IGTK key bug that has existed since the MVM driver was introduced
* fix some fw capabilities checks that got accidentally inverted
rtl8xxxu
* fix typo on variable name
ath10k
* fix deadlock when peer cannot be created
* fix crash related to printing features
* fix deadlock while processing rx_in_ord_ind
ath9k
* fix GPIO mask regression for AR9462 and AR9565
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.8. Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
Calling sdio_claim_host() from the interface independent part of
the mwifiex driver is not only a layering violation, but also causes
a link error if MMC support is disabled, or if CONFIG_MMC=m
and CONFIG_MWIFIEX=y:
drivers/net/built-in.o: In function `mwifiex_fw_dpc':
:(.text+0xff138): undefined reference to `sdio_claim_host'
:(.text+0xff158): undefined reference to `sdio_release_host'
The right way to do this is to have the sdio specific code in the
sdio driver front-end, and we already have a callback pointer that
we can use for this after exporting the generic fw download
function from the core driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 65c71efe1c ("mwifiex: fix racing condition when downloading firmware")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without this including cfg80211.h in a wrong order could result in:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:122:24: error: array type has incomplete element type
struct brcmf_wsec_key key[BRCMF_MAX_DEFAULT_KEYS];
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:291:24: error: field ‘p2p’ has incomplete type
struct brcmf_p2p_info p2p;
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:297:27: error: field ‘pmk_list’ has incomplete type
struct brcmf_pmk_list_le pmk_list;
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:317:28: error: field ‘assoclist’ has incomplete type
struct brcmf_assoclist_le assoclist;
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This attribute was added 3 years ago by
commit 3eacf86655 ("brcmfmac: introduce brcmf_cfg80211_vif structure")
but it remains unused since then. It seems we can safely drop it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Per Michael Büsch: "All a-phy code is usused", so remove it all.
Cc: Michael Büsch <m@bues.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-6 reports the following error with -Werror=unused-const-variable.
drivers/net/wireless/broadcom/b43/phy_a.c:576:40: error:
'b43_phyops_a' defined but not used
Per Michael Büsch: "All a-phy code is usused", so remove it all,
and move the remaining Type-G initialization code into phy_g.c.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Cc: Michael Büsch <m@bues.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
alloc_workqueue replaces deprecated create_workqueue().
In if_sdio.c, the workqueue card->workqueue has workitem
&card->packet_worker, which is mapped to if_sdio_host_to_card_worker.
The workitem is involved in sending packets to firmware.
Forward progress under memory pressure is a requirement here.
In if_spi.c, the workqueue card->workqueue has workitem
&card->packet_worker, which is mapped to if_spi_host_to_card_worker.
The workitem is involved in sending command packets from the host.
Forward progress under memory pressure is a requirement here.
Dedicated workqueues have been used in both cases since the workitems
on the workqueues are involved in normal device operation with
WQ_MEM_RECLAIM set to gurantee forward progress under memory pressure.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the calls to flush_workqueue() before
destroy_workqueue() have been dropped.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The bus rx sequence is not in order because that control and event
frames always cause immediate send, but data frames may be held
for glomming in firmware side. It is not actually an error as the
packets are still processed even if the RX sequence is not in order.
Therefor the error message is rephrased and changed to a debug
message.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for the new PCIE devices 43525 and 43465.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using nmap tool with FMAC, the nmap packets were be dropped by kernel
because the size was too short. The kernel message showed like
"nmap: packet size is too short (42 <= 50)". It is caused by the packet
length is shorter than ndev->hard_header_len. According to definition of
LL_RESERVED_SPACE() and hard_header_len, we should use hard_header_len
to reserve for L2 header, like ethernet header(ETH_HLEN) in our case and
use needed_headroom for the additional headroom needed by hardware.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The error message is given for something that is not an error here as
the drive strength configuration may not be applicable for specific
devices. Therefor the error message is rephrased and changed to a
debug message.
Signed-off-by: Wright Feng <wright.feng@broadcom.com>
[arend@broadcom.com: rephrase commit message]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SKBs can come with a prioriy. Currently a priority of 0..7 is
assumed. But this assumption is incorrect. To fix this any
priority of 0 or higher then 7 will be adjusted by calling
cfg80211_classify8021d
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
