x200 does not enable any way to programmatically obtain bus clock
speed. Bclk for the architecture has a fixed value of 100 MHz.
At the same time x200 cannot be included in has_snb_msrs since
it does not support C7 idle state.
prior to this patch, MHz values reported on this chip
were erroneously calculated using bclk of 133MHz,
causing MHz values to be reported 33% higher than actual.
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat -i interval_sec
will sample and display statistics every interval_sec.
interval_sec used to be a whole number of seconds,
but now we accept a decimal, as small as 0.001 sec (1 ms).
Signed-off-by: Len Brown <len.brown@intel.com>
When building with gcc 6 we're getting various build warnings that just
require some trivial function declaration and call fixes:
turbostat.c: In function ‘dump_cstate_pstate_config_info’:
turbostat.c:1973:1: warning: type of ‘family’ defaults to ‘int’
dump_cstate_pstate_config_info(family, model)
turbostat.c:1973:1: warning: type of ‘model’ defaults to ‘int’
turbostat.c: In function ‘get_tdp’:
turbostat.c:2145:8: warning: type of ‘model’ defaults to ‘int’
double get_tdp(model)
turbostat.c: In function ‘perf_limit_reasons_probe’:
turbostat.c:2259:6: warning: type of ‘family’ defaults to ‘int’
void perf_limit_reasons_probe(family, model)
turbostat.c:2259:6: warning: type of ‘model’ defaults to ‘int’
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-wbicer8n0s9qe6ql8h9x478e@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
for debugging, dump a few more fields:
CPUID(1): SSE3 MONITOR EIST TM2 TSC MSR ACPI-TM TM
cpu0: MSR_IA32_MISC_ENABLE: 0x00850089 (TCC EIST MONITOR)
Signed-off-by: Len Brown <len.brown@intel.com>
Fix the following build error by including limits.h -
utils/cpufreq-info.c: In function ‘get_latency’:
utils/cpufreq-info.c:437:29: error: ‘UINT_MAX’ undeclared (first use in
this function)
if (!latency || latency == UINT_MAX) {
^
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Fixes: e98f033f94 (cpupower: fix how "cpupower frequency-info" interprets latency)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All tool/utility signons.
Dual-license module header.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-sleep:
PM / sleep: Add support for read-only sysfs attributes
* pm-tools:
cpupower: fix how "cpupower frequency-info" interprets latency
cpupower: rework the "cpupower frequency-info" command
cpupower: Do not analyse offlined cpus
cpupower: Provide STATIC variable in Makefile for debug builds
cpupower: Fix precedence issue
ACPICA commit 0d784a90bc3aac75227c4459c3553de18b9ebe7a
Document one of the option string operators.
Link: https://github.com/acpica/acpica/commit/0d784a90
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit dfa394471f6c01b2ee9433dbc143ec70cb9bca72
Mostly indentation inconsistencies across the code. Split
some long lines, etc.
Link: https://github.com/acpica/acpica/commit/dfa39447
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds a userspace tool to access Linux kernel AML debugger
interface.
Tow modes are supported by this tool:
1. Interactive: Users are able to launch a debugging shell to talk with
in-kernel AML debugger.
Note that it's user duty to ensure kernel runtime integrity by using
this debugging tool:
A. Some control methods evaluated by the users may result in kernel
panics if those control methods shouldn't be evaluated by the OSPMs
according to the current BIOS/OS configurations.
B. Currently if a single stepping evaluation couldn't run to an end,
then the synchronization primitives acquired by the evaluation may
block normal OSPM control method evaluations.
2. Batch: Users are able to execute debugger commands in a script.
Note that in addition to the above duties, it's user duty to ensure
script runtime integrity by using this debugging tool in this mode:
C. Currently only those commands that are not used for single stepping
are suitable to be used in this mode.
D. If the execution of the command may cause a failure that could result
in an endless kernel execution, the execution of the script may also
get blocked.
To exit the utility, currently "exit/quit" commands are recommended, but
ctrl-C" can also be used.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
the intel-pstate driver does not support the ondemand governor and does not
have a valid value in
/sys/devices/system/cpu/cpu[x]/cpufreq/cpuinfo_transition_latency. The
intel-pstate driver sets cpuinfo_transition_latency to CPUFREQ_ETERNAL (-1),
the value written into cpuinfo_transition_latency is defind as an unsigned
int so checking the read value against max unsigned int will determine if the
value is valid.
Signed-off-by: Jacob Tanenbaum <jtanenba@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
this patch makes two changes to the way that "cpupower
frequancy-info" operates
1. make it so that querying individual values always returns a
message to the user
currently cpupower frequency info doesn't return anything to the user when
querying an individual value cannot be returned
[root@amd-dinar-09 cpupower]# cpupower -c 4 frequency-info -d
analyzing CPU 4:
[root@amd-dinar-09 cpupower]#
I added messages so that each query prints a message to the terminal
[root@amd-dinar-09 cpupower]# ./cpupower -c 4 frequency-info -d
analyzing CPU 4:
no or unknown cpufreq driver is active on this CPU
[root@amd-dinar-09 cpupower]#
(this is just one example)
2. change debug_output_one() to use the functions already provided
by cpufreq-info.c to query individual values of interest.
Signed-off-by: Jacob Tanenbaum <jtanenba@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use sysfs_is_cpu_online(cpu) instead of cpufreq_cpu_exists(cpu) to detect offlined cpus.
Re-arrange printfs slightly to have a consistent output even if you have multiple CPUs
as output and even if offlined cores are in between.
Signed-off-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When working on cpupower code, you often want to compile library code into the
binary.
This allows to execute modified cpupower code, even with library changes
without doing "make install"
Signed-off-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
MSR_PLATFORM_INFO is the new name for MSR_NHM_PLATFORM_INFO
no functional change
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-tools:
Creating a common structure initialization pattern for struct option
cpupower: Enable disabled Cstates if they are below max latency
cpupower: Remove debug message when using cpupower idle-set -D switch
cpupower: cpupower monitor reports uninitialized values for offline cpus
tools/power turbostat: bugfix: print MAX_NON_TURBO_RATIO
tools/power turbostat: simplify Bzy_MHz calculation
This patch tries to creates a common structure initialization
within the cpupower tool.
Previously the ``struct option`` was initialized
using `designated initializer` technique which was
not needed. There were conflicting initialization methods seen with
bench/main.c & others.
Signed-off-by: Sriram Raghunathan <sriram@marirs.net.in>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpupower idle-set -D <latency>
currently only disables all C-states that have a higher latency than the
specified <latency>. But if deep sleep states were already disabled and
have a lower latency, they should get enabled again.
For example:
This call:
cpupower idle-set -D 30
disables all C-states with a higher or equal latency than 30.
If one then calls:
cpupower idle-set -D 100
C-states with a latency between 30-99 will get enabled again with this patch
now. It is ensured that only C-states with a latency of 100 and higher are
disabled.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[root@hp-dl980g7-02 linux]# cpupower monitor
...
5472| 0| 1|******|******|******|******|| 0.00| 0.00| 0.00| 0.00| 0.00 *is offline
10567| 0| 159|******|******|******|******|| 0.00| 0.00| 0.00| 0.00| 0.00 *is offline
1661206560|859272560| 150|******|******|******|******|| 0.00| 0.00| 0.00| 0.00| 0.00 *is offline
1661206560|943093104| 140|******|******|******|******|| 0.00| 0.00| 0.00| 0.00| 0.00 *is offline
because of this cpupower also holds the incorrect value for the number
of physical packages in the machine
Changed cpupower to initialize the values of an offline cpu's socket and
core to -1, warn the user that one or more cpus is/are
offline and not print statistics for offline cpus.
This fix hides offlined cores where topology cannot be accessed.
With a recent kernel patch suggested from Prarit Bhargava it may be possible
that soft offlined cores' topology can still be parsed.
This patch would then show which cores in which package/socket are offline,
when sane toplogoy information is available.
Signed-off-by: Jacob Tanenbaum <jtanenba@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
MSR_TURBO_ACTIVATION_RATIO: 0x00000016 (MAX_NON_TURBO_RATIO=6 lock=0)
should print all 7 bits of MAX_NON_TURBO_RATIO (in decimal):
MSR_TURBO_ACTIVATION_RATIO: 0x00000016 (MAX_NON_TURBO_RATIO=22 lock=0)
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA commit bed456ed2976bdaafdef406b982fdf6c539befc0
Removed some extraneous defines, reordered others.
Link: https://github.com/acpica/acpica/commit/bed456ed
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bzy_MHz = TSC_delta*tsc_tweak/APERF_delta/MPERF_delta/measurement_interval
becomes
Bzy_MHz = base_mhz/APERF_delta/MPERF_delta
on systems which support MSR_NHM_PLATFORM_INFO.
base_mhz is calculated directly from the base_ratio
reported in MSR_NHM_PLATFORM_INFO * bclk,
and bclk is discovered via MSR or cpuid.
This reduces the dependency of Bzy_MHz calculation on the TSC.
Previously, there were 4 TSC readings required in each caculation,
the raw TSC delta combined with the measurement_interval.
This also removes the "tsc_tweak" correction factor used when
TSC runs on a different base clock from the CPU's bclk.
After this change, tsc_tweak is used only for %Busy.
The end-result should be a Bzy_MHz result slightly less prone to jitter.
Signed-off-by: Len Brown <len.brown@intel.com>
On a Skylake with 1500MHz base frequency,
the TSC runs at 1512MHz.
This is because the TSC is no longer in the n*100 MHz BCLK domain,
but is now in the m*24MHz crystal clock domain. (24 MHz * 63 = 1512 MHz)
This adds error to several calculations in turbostat,
unless the TSC sample sizes are adjusted for this difference.
Note that calculations in the time domain are immune
from this issue, as the timing sub-system has already
calibrated the TSC against a known wall clock.
AVG_MHz = APERF_delta/measurement_interval
need no adjustment. APERF_delta is in the BCLK domain,
and measurement_interval is in the time domain.
TSC_MHz = TSC_delta/measurement_interval
needs no adjustment -- as we really do want to report
the actual measured TSC delta here, and measurement_interval
is in the accurate time domain.
%Busy = MPERF_delta/TSC_delta
needs adjustment to use TSC_BCLK_DOMAIN_delta.
TSC_BCLK_DOMAIN_delta = TSC_delta * base_hz / tsc_hz
Bzy_MHz = TSC_delta/APERF_delta/MPERF_delta/measurement_interval
need adjustment as above.
No other metrics in turbostat need to be adjusted.
Before:
CPU Avg_MHz %Busy Bzy_MHz TSC_MHz
- 550 24.84 2216 1512
0 2191 98.73 2219 1514
2 0 0.01 2130 1512
1 9 0.43 2016 1512
3 2 0.08 2016 1512
After:
CPU Avg_MHz %Busy Bzy_MHz TSC_MHz
- 550 25.05 2198 1512
0 2190 99.62 2199 1512
2 0 0.01 2152 1512
1 9 0.46 2000 1512
3 2 0.10 2000 1512
Note that in this example, the "Before" Bzy_MHz
was reported as exceeding the 2200 max turbo rate.
Also, even a pinned spin loop would not be reported
as over 99% busy.
Signed-off-by: Len Brown <len.brown@intel.com>
KNL increments APERF and MPERF every 1024 clocks.
This is compliant with the architecture specification,
which requires that only the ratio of APERF/MPERF need be valid.
However, turbostat takes advantage of the fact that these
two MSRs increment every un-halted clock
at the actual and base frequency:
AVG_MHz = APERF_delta/measurement_interval
%Busy = MPERF_delta/TSC_delta
This quirk is needed for these calculations to also work on KNL,
which would otherwise show a value 1024x smaller than expected.
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Staring in Linux-4.3-rc1,
commit 6fb3143b56 ("tools/power turbostat: dump CONFIG_TDP")
touches MSR 0x648, which is not supported on IVB-Xeon.
This results in "turbostat --debug" exiting on those systems:
turbostat: /dev/cpu/2/msr offset 0x648 read failed: Input/output error
Remove IVB-Xeon from the list of machines supporting with that MSR.
Signed-off-by: Len Brown <len.brown@intel.com>
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore,
Lv Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to
AML method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool
to be built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future
introduction of CPPC support and ACPI PCC mailbox driver
updates (Ashwin Chaugule).
- ACPI interrupts enumeration fix for a regression related
to the handling of IRQ attribute conflicts between MADT
and the ACPI namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael
J Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups
(Pan Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it
to preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support
for them in the OPP framework and in the cpufreq-dt driver plus
related OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=fTgI
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"From the number of commits perspective, the biggest items are ACPICA
and cpufreq changes with the latter taking the lead (over 50 commits).
On the cpufreq front, there are many cleanups and minor fixes in the
core and governors, driver updates etc. We also have a new cpufreq
driver for Mediatek MT8173 chips.
ACPICA mostly updates its debug infrastructure and adds a number of
fixes and cleanups for a good measure.
The Operating Performance Points (OPP) framework is updated with new
DT bindings and support for them among other things.
We have a few updates of the generic power domains framework and a
reorganization of the ACPI device enumeration code and bus type
operations.
And a lot of fixes and cleanups all over.
Included is one branch from the MFD tree as it contains some
PM-related driver core and ACPI PM changes a few other commits are
based on.
Specifics:
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore, Lv
Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to AML
method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool to be
built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future introduction
of CPPC support and ACPI PCC mailbox driver updates (Ashwin
Chaugule).
- ACPI interrupts enumeration fix for a regression related to the
handling of IRQ attribute conflicts between MADT and the ACPI
namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi
Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael J
Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan
Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it to
preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support for
them in the OPP framework and in the cpufreq-dt driver plus related
OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu)"
* tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (180 commits)
cpufreq: speedstep-lib: Use monotonic clock
cpufreq: powernv: Increase the verbosity of OCC console messages
cpufreq: sfi: use kmemdup rather than duplicating its implementation
cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor()
cpufreq: rename cpufreq_real_policy as cpufreq_user_policy
cpufreq: remove redundant 'policy' field from user_policy
cpufreq: remove redundant 'governor' field from user_policy
cpufreq: update user_policy.* on success
cpufreq: use memcpy() to copy policy
cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event
cpufreq: mediatek: Add MT8173 cpufreq driver
dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings
PM / Domains: Fix typo in description of genpd_dev_pm_detach()
PM / Domains: Remove unusable governor dummies
PM / Domains: Make pm_genpd_init() available to modules
PM / domains: Align column headers and data in pm_genpd_summary output
powercap / RAPL: disable the 2nd power limit properly
tools: cpupower: Fix error when running cpupower monitor
PM / OPP: Drop unlikely before IS_ERR(_OR_NULL)
PM / OPP: Fix static checker warning (broken 64bit big endian systems)
...
* pm-tools:
tools: cpupower: Fix error when running cpupower monitor
tools/power turbostat: fix typo on DRAM column in Joules-mode
cpupower: Do not change the frequency of offline cpu
tools/power turbostat: fix parameter passing for forked command
tools/power turbostat: dump CONFIG_TDP
tools/power turbostat: cpu0 is no longer hard-coded, so update output
tools/power turbostat: update turbostat(8)
* powercap:
powercap / RAPL: disable the 2nd power limit properly
powercap / RAPL: Add support for Broadwell-H
powercap / RAPL: Add support for Skylake H/S
get_cpu_topology() tries to get topology info from all cpus by reading
files in the topology sysfs dir. If a cpu is offlined, since it doesn't
have topology dir, this function fails and returns -1. This causes
functions relying on get_cpu_topology() to fail. For example-
$ cpupower monitor
Cannot read number of available processors
Fix this by skipping fetching topology info for offline cpus.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reported-by: Pavaman Subramaniyam <pavsubra@linux.vnet.ibm.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull turbostat changes for v4.3 from Len Brown.
* 'turbostat' of https://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: fix typo on DRAM column in Joules-mode
tools/power turbostat: fix parameter passing for forked command
tools/power turbostat: dump CONFIG_TDP
tools/power turbostat: cpu0 is no longer hard-coded, so update output
tools/power turbostat: update turbostat(8)
This patch allows EC userspace tool to be built as an ACPI tool.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch splits tools/power/acpi/Makefile to support descend compling for
ACPI tools. In this patch tools/ec related stuff is removed as it is
originally not enabled.
Also a missing .o (utnonansi.o) is added to the acpidump/Makefile.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Check if the cpu is online before changing the frequency/governor of
the cpu.
Reported-by: Pavaman Subramaniyam <pavsubra@linux.vnet.ibm.com>
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
turbostat supports forked command when sampling cpu state. However,
the forked command is not allowed to be executed with options, otherwise
turbostat might regard these options as invalid turbostat options.
For example:
./turbostat stress -c 4 -t 10
./turbostat: unrecognized option '-t'
Reported-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now that there is no paravirt TSC, the "native" is
inappropriate. The function does RDTSC, so give it the obvious
name: rdtsc().
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/fd43e16281991f096c1e4d21574d9e1402c62d39.1434501121.git.luto@kernel.org
[ Ported it to v4.2-rc1. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that the ->read_tsc() paravirt hook is gone, rdtscll() is
just a wrapper around native_read_tsc(). Unwrap it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/d2449ae62c1b1fb90195bcfb19ef4a35883a04dc.1434501121.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Fix system resume problems related to 32-bit and 64-bit versions
of the Firmware ACPI Control Structure (FACS) in the firmare (Lv
Zheng).
- Fix double initialization of the FACS (Lv Zheng).
- Add _CLS object processing code to ACPICA (Suravee Suthikulpanit).
- Add support for the (currently missing) new GIC version field in
the Multiple APIC Description Table (MADT) (Hanjun Guo).
- Add support for overriding objects in the ACPI namespace to
ACPICA and OSDT support (Lv Zheng, Bob Moore, Zhang Rui).
- Updates related to the TCPA and TPM2 ACPI tables (Bob Moore).
- Restore the commit modifying _REV to always return "2" (as
required by ACPI 6) and add a blacklisting mechanism for
systems that may be affected by that change (Rafael J Wysocki).
- Assorted fixes and cleanups (Bob Moore, Lv Zheng, Sascha Wildner).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=MlWS
-----END PGP SIGNATURE-----
Merge tag 'acpica-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPICA updates from Rafael Wysocki:
"Additional ACPICA material for v4.2-rc1
This will update the ACPICA code in the kernel to upstream revision
20150619 (a bug-fix release mostly including stable-candidate fixes)
and restore an earlier ACPICA commit that had to be reverted due to a
regression introduced by it (the regression is addressed by
blacklisting the only known system affected by it to date).
The only new feature added by this update is the support for
overriding objects in the ACPI namespace and a new ACPI table that can
be used for that called the Override System Definition Table (OSDT).
That should allow us to "patch" the ACPI namespace built from
incomplete or incorrect ACPI System Definition tables (DSDT, SSDT)
during system startup without the need to provide replacements for all
of those tables in the future.
Specifics:
- Fix system resume problems related to 32-bit and 64-bit versions of
the Firmware ACPI Control Structure (FACS) in the firmare (Lv
Zheng)
- Fix double initialization of the FACS (Lv Zheng)
- Add _CLS object processing code to ACPICA (Suravee Suthikulpanit)
- Add support for the (currently missing) new GIC version field in
the Multiple APIC Description Table (MADT) (Hanjun Guo)
- Add support for overriding objects in the ACPI namespace to ACPICA
and OSDT support (Lv Zheng, Bob Moore, Zhang Rui)
- Updates related to the TCPA and TPM2 ACPI tables (Bob Moore)
- Restore the commit modifying _REV to always return "2" (as required
by ACPI 6) and add a blacklisting mechanism for systems that may be
affected by that change (Rafael J Wysocki)
- Assorted fixes and cleanups (Bob Moore, Lv Zheng, Sascha Wildner)"
* tag 'acpica-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
Revert 'Revert "ACPICA: Permanently set _REV to the value '2'."'
ACPI / init: Make it possible to override _REV
ACPICA: Update version to 20150619
ACPICA: Comment update, no functional change
ACPICA: Update TPM2 ACPI table
ACPICA: Update definitions for the TCPA and TPM2 ACPI tables
ACPICA: Split C library prototypes to new header
ACPICA: De-macroize calls to standard C library functions
ACPI / acpidump: Update acpidump manual
ACPICA: acpidump: Convert the default behavior to dump from /sys/firmware/acpi/tables
ACPICA: acpidump: Allow customized tables to be dumped without accessing /dev/mem
ACPICA: Cleanup output for the ASL Debug object
ACPICA: Update for acpi_install_table memory types
ACPICA: Namespace: Change namespace override to avoid node deletion
ACPICA: Namespace: Add support of OSDT table
ACPICA: Namespace: Add support to allow overriding objects
ACPICA: ACPI 6.0: Add values for MADT GIC version field
ACPICA: Utilities: Add _CLS processing
ACPICA: Add dragon_fly support to unix file mapping file
ACPICA: EFI: Add EFI interface definitions to eliminate dependency of GNU EFI
...
ACPICA commit 3b1026e0bdd3c32eb6d5d313f3ba0b1fee7597b4
ACPICA commit 00f0dc83f5cfca53b27a3213ae0d7719b88c2d6b
ACPICA commit 47d22a738d0e19fd241ffe4e3e9d4e198e4afc69
Across all of ACPICA. Replace C library macros such as ACPI_STRLEN with the
standard names such as strlen. The original purpose for these macros is
long since obsolete.
Also cast various invocations as necessary. Bob Moore, Jung-uk Kim, Lv Zheng.
Link: https://github.com/acpica/acpica/commit/3b1026e0
Link: https://github.com/acpica/acpica/commit/00f0dc83
Link: https://github.com/acpica/acpica/commit/47d22a73
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Jung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch updates acpidump manual according to the recent changes.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 04c3bd7e9d6aeb2b3edebe99c90dc271ae4e6353
In order to work without any additional option to dump tables when /dev/mem
doesn't exist, this patch switches the default behavior of acpidump to dump
from /sys/firmware/acpi/tables. Reported by Al Stone, Fixed by Lv Zheng.
Link: https://github.com/acpica/acpica/commit/04c3bd7e
Reported-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit ab29013cfa2424140446aff196a70b211ab343a9
The /dev/mem can be configured out, in which case, acpidump should still
work with "-c" option as tables can be found in /sys/firmware/acpi/tables.
This patch allows acpidump to work without /dev/mem.
This patch has been tested with "acpidump -c" and "acpidump -c -n FADT".
And it worked as expected. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/ab29013c
Reported-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- ACPICA update to upstream revision 20150515 including basic
support for ACPI 6 features: new ACPI tables introduced by
ACPI 6 (STAO, XENV, WPBT, NFIT, IORT), changes related to the
other tables (DTRM, FADT, LPIT, MADT), new predefined names
(_BTH, _CR3, _DSD, _LPI, _MTL, _PRR, _RDI, _RST, _TFP, _TSN),
fixes and cleanups (Bob Moore, Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation
in Windows (Rafael J Wysocki).
- Rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling
of DMI quirks that may be involved in that and to make the
code generally more straightforward (Hans de Goede).
- Fixes for the ACPI Embedded Controller (EC) driver related to
the handling of EC transactions (Lv Zheng).
- Fix for a regression related to the ACPI resources management
and resulting from a recent change of ACPI initialization code
ordering (Rafael J Wysocki).
- Fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the
code that switches the platform over to the ACPI mode too
early in the initialization sequence (Rafael J Wysocki).
- Support for the ACPI _CCA device configuration object related
to DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- Cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- Assorted cleanups related to ACPI (Dominik Brodowski. Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- Fix for a long-standing issue causing General Protection Faults
to be generated occasionally on return to user space after resume
from ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- Fix to make the suspend core code return -EBUSY consistently in
all cases when system suspend is aborted due to wakeup detection
(Ruchi Kandoi).
- Support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- New tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- Wakeup sources framework enhancements (Jin Qian).
- New macro for noirq system PM callbacks (Grygorii Strashko).
- Assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should
reduce the overhead of these operations quite a bit, unless the
CPU in question is physically going away (Viresh Kumar, Saravana
Kannan).
- Serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- Assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- New Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- Updates for the common clock operations support code in the PM
core (Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- Fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- Runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=7jTj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
* pnp:
PNP / ACPI: use unsigned int in pnpacpi_encode_resources()
PNP / ACPI: use u8 instead of int in acpi_resource_extended_irq context
* pm-tools:
cpupower: mperf monitor: fix output in MAX_FREQ_SYSFS mode
Config TDP is a feature that allows parts to be configured
for different thermal limits after they have left the factory.
This can have an effect on the operation of the part,
particularly in determiniing...
Max Non-turbo Ratio
Turbo Activation Ratio
Signed-off-by: Len Brown <len.brown@intel.com>
The --debug option reads a number of per-package MSRs.
Previously we explicitly read them on cpu0, but recently
turbostat changed to read them on the current "base_cpu".
Update the print-out to reflect base_cpu, rather than
the hard-coded cpu0.
Signed-off-by: Len Brown <len.brown@intel.com>
This header containing all MSRs and respective bit definitions
got exported to userspace in conjunction with the big UAPI
shuffle.
But, it doesn't belong in the UAPI headers because userspace can
do its own MSR defines and exporting them from the kernel blocks
us from doing cleanups/renames in that header. Which is
ridiculous - it is not kernel's job to export such a header and
keep MSRs list and their names stable.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1433436928-31903-19-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Remove reference to the original Nehalem Turbo white paper,
since it has moved, and these mechanisms have now long since
been documented in the Software Developer's Manual.
Reported-by: Jeremie Lagraviere <jeremie@simula.no>
Signed-off-by: Len Brown <len.brown@intel.com>
There is clearly wrong output when mperf monitor runs in MAX_FREQ_SYSFS mode:
average frequency shows in kHz unit (despite the intended output to be in MHz),
and percentages for C state information are all wrong (including high/negative
values shown).
The problem is that the max_frequency read on initialization isn't used where it
should have been used on mperf_get_count_percent (to estimate the number of
ticks in the given time period), and the value we read from sysfs is in kHz, so
we must divide it to get the MHz value to use in current calculations.
While at it, also I fixed another small issues in the debug output of
max_frequency value in mperf_get_count_freq.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linux-3.7 added CONFIG_BOOTPARAM_HOTPLUG_CPU0,
allowing systems to offline cpu0.
But when cpu0 is offline, turbostat will not run:
# turbostat ls
turbostat: no /dev/cpu/0/msr
This patch replaces the hard-coded use of cpu0 in turbostat
with the current cpu, allowing it to run without a cpu0.
Fewer cross-calls may also be needed due to use of current cpu,
though this hard-coding was used only for the --debug preamble.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When EPB is 0xF, turbosat was incorrectly describing it as "custom"
instead of calling it "powersave":
< cpu0: MSR_IA32_ENERGY_PERF_BIAS: 0x0000000f (custom)
> cpu0: MSR_IA32_ENERGY_PERF_BIAS: 0x0000000f (powersave)
Signed-off-by: Len Brown <len.brown@intel.com>
Changes mainly to account for minor differences in Knights Landing(KNL):
1. KNL supports C1 and C6 core states.
2. KNL supports PC2, PC3 and PC6 package states.
3. KNL has a different encoding of the TURBO_RATIO_LIMIT MSR
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Without this update, turbostat displays only 2 threads per core.
Some processors, such as Xeon Phi, have more.
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
- Fix a build warning in the intel_pstate driver showing up in non-SMP
builds (Borislav Petkov).
- Change one of the intel_pstate's P-state selection parameters for
Baytrail and Cherrytrail CPUs to significantly improve performance
at the cost of a small increase in energy consumption (Kristen
Carlson Accardi).
- Fix a NULL pointer dereference in the ACPI EC driver due to an unsafe
list walk in the query handler removal routine (Chris Bainbridge).
- Get rid of a false-positive lockdep warning in the ACPI container
hot-remove code (Rafael J Wysocki).
- Prevent the ACPI device enumeration code from creating device
objects of a wrong type in some cases (Rafael J Wysocki).
- Add Skylake processors support to the Intel RAPL power capping
driver (Brian Bian).
- Drop the stale MAINTAINERS entry for the ACPI dock driver that is
regarded as part of the ACPI core and maintained along with it now
(Chao Yu).
- Fix cpupower tool breakage caused by a library API change in libpci
3.3.0 (Lucas Stach).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=0bKD
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"These are fixes mostly (intel_pstate, ACPI core, ACPI EC driver,
cpupower tool), a new CPU ID for the Intel RAPL driver and one
intel_pstate driver improvement that didn't make it to my previous
pull requests due to timing.
Specifics:
- Fix a build warning in the intel_pstate driver showing up in
non-SMP builds (Borislav Petkov)
- Change one of the intel_pstate's P-state selection parameters for
Baytrail and Cherrytrail CPUs to significantly improve performance
at the cost of a small increase in energy consumption (Kristen
Carlson Accardi)
- Fix a NULL pointer dereference in the ACPI EC driver due to an
unsafe list walk in the query handler removal routine (Chris
Bainbridge)
- Get rid of a false-positive lockdep warning in the ACPI container
hot-remove code (Rafael J Wysocki)
- Prevent the ACPI device enumeration code from creating device
objects of a wrong type in some cases (Rafael J Wysocki)
- Add Skylake processors support to the Intel RAPL power capping
driver (Brian Bian)
- Drop the stale MAINTAINERS entry for the ACPI dock driver that is
regarded as part of the ACPI core and maintained along with it now
(Chao Yu)
- Fix cpupower tool breakage caused by a library API change in libpci
3.3.0 (Lucas Stach)"
* tag 'pm+acpi-4.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: Add a scan handler for PRP0001
ACPI / scan: Annotate physical_node_lock in acpi_scan_is_offline()
ACPI / EC: fix NULL pointer dereference in acpi_ec_remove_query_handler()
MAINTAINERS: remove maintainship entry of docking station driver
powercap / RAPL: Add support for Intel Skylake processors
cpufreq: intel_pstate: Fix an annoying !CONFIG_SMP warning
intel_pstate: Change the setpoint for Atom params
cpupower: fix breakage from libpci API change
Pull turbostat update from Len Brown:
"Updates to the turbostat utility.
Just one kernel dependency in this batch -- added a #define to
msr-index.h"
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
x86 msr-index: define MSR_TURBO_RATIO_LIMIT,1,2
tools/power turbostat: label base frequency
tools/power turbostat: update PERF_LIMIT_REASONS decoding
tools/power turbostat: simplify default output
* pm-cpufreq:
cpufreq: intel_pstate: Fix an annoying !CONFIG_SMP warning
intel_pstate: Change the setpoint for Atom params
* powercap:
powercap / RAPL: Add support for Intel Skylake processors
* pm-tools:
cpupower: fix breakage from libpci API change
HSW expanded MSR_PKG_CST_CONFIG_CONTROL.Package-C-State-Limit,
from bits[2:0] used by previous implementations, to [3:0].
The value 1000b is unlimited, and is used by BDW and SKL too.
Signed-off-by: Len Brown <len.brown@intel.com>
While not yet documented in the Software Developer's Manual,
the data-sheet for modern Xeon states that DRAM RAPL ENERGY units
are fixed at 15.3 uJ, rather than being discovered via MSR.
Before this patch, DRAM energy on these products is over-stated by turbostat
because the RAPL units are 4x larger.
ref: "Xeon E5-2600 v3/E5-1600 v3 Datasheet Volume 2"
http://www.intel.com/content/dam/www/public/us/en/documents/datasheets/xeon-e5-v3-datasheet-vol-2.pdf
Signed-off-by: Andrey Semin <andrey.semin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Skylake adds some additional residency counters.
Skylake supports a different mix of RAPL registers
from any previous product.
In most other ways, Skylake is like Broadwell.
Signed-off-by: Len Brown <len.brown@intel.com>
Since commit ee0778a301
("tools/power: turbostat: make Makefile a bit more capable")
turbostat's Makefile is using
[...]
BUILD_OUTPUT := $(PWD)
[...]
which obviously causes trouble when building "turbostat" with
make -C /usr/src/linux/tools/power/x86/turbostat ARCH=x86 turbostat
because GNU make does not update nor guarantee that $PWD is set.
This patch changes the Makefile to use $CURDIR instead, which GNU make
guarantees to set and update (i.e. when using "make -C ...") and also
adds support for the O= option (see "make help" in your root of your
kernel source tree for more details).
Link: https://bugs.gentoo.org/show_bug.cgi?id=533918
Fixes: ee0778a301 ("tools/power: turbostat: make Makefile a bit more capable")
Signed-off-by: Thomas D. <whissi@whissi.de>
Cc: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some distros (Ubuntu) ship the msr driver as a module.
If turbosat is run as root on those systems, and discovers
that there is no /dev/cpu/cpu0/msr, it will now "modprobe msr"
for the user.
If not root, the modprobe attempt will fail, and turbostat will exit as before:
turbostat: no /dev/cpu/0/msr, Try "# modprobe msr" : No such file or directory
Signed-off-by: Len Brown <len.brown@intel.com>
s/MSR_NHM_TURBO_RATIO_LIMIT/MSR_TURBO_RATIO_LIMIT/
s/MSR_IVT_TURBO_RATIO_LIMIT/MSR_TURBO_RATIO_LIMIT1/
syntax only -- use the documented strings describing these registers.
Signed-off-by: Len Brown <len.brown@intel.com>
libpci 3.3.0 introduced an additional member in the pci_filter struct
which needs to be initialized to -1 to get the same behavior as before
the API change. The libpci internal helpers got updated accordingly,
but as the cpupower pci helpers initialized the struct themselves the
behavior changed.
Use the libpci helper pci_filter_init() to fix this and guard against
similar breakages in the future.
This fixes probing of the AMD fam12h/14h cpuidle monitor on systems
with libpci >= 3.3.0.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 84f3569db7accc576ace2dae81d101467254fe9d
Was using %d instead of properly using %u.
This patch only affects acpidump tool.
Link: https://github.com/acpica/acpica/commit/84f3569d
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 9e2d8180f4d5e61949b17513bae8aff6412f62dd
The offset calculation needn't convert a pointer to a special integer type.
So this patch uses ACPI_TO_INTEGER() instead.
This patch only affects acpidump tool.
Link: https://github.com/acpica/acpica/commit/9e2d8180
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
syntax only.
The cool kids are now using the phrase "base frequency",
where in the past we used "max non-turbo frequency" or "TSC frequency".
This distinction becomes important when a processor has a TSC
that runs at a different speed than the "base frequency".
Signed-off-by: Len Brown <len.brown@intel.com>
cosmetic only.
order the decoding of MSR_PERF_LIMIT_REASONS bits
from MSB to LSB -- which you notice when more than 1 bit is set
and you are, say, comparing the output to the documentation...
Signed-off-by: Len Brown <len.brown@intel.com>
Casual turbostat users generally just want to know MHz.
So by default, just print enough information to make sense of MHz.
All the other configuration data and columns for C-states and temperature etc,
are printed with the --debug option.
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 5c1de006e8.
While the original commit makes it easier to run cpupower from the
local build directory, it also leaves the binary with a rather poor
rpath of './' in it after it is installed on a system via 'make install'.
This is considered bad practice and can cause cpupower to fail in
rpmbuild with the following error:
ERROR 0004: file '/usr/bin/cpupower' contains an insecure rpath './' in [./]
error: Bad exit status from /var/tmp/rpm-tmp.A6u26r (%install)
Bad exit status from /var/tmp/rpm-tmp.A6u26r (%install)
Developers should be able to use LD_LIBRARY_PATH to achieve the same
effect and not introduce rpath into the binary.
Signed-off-by: Josh Boyer <jwboyer@feoraproject.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-tools:
tools/power turbostat: relax dependency on APERF_MSR
tools/power turbostat: relax dependency on invariant TSC
tools/power turbostat: decode MSR_*_PERF_LIMIT_REASONS
tools/power turbostat: relax dependency on root permission
cpupower Makefile change to help run the tool without 'make install'
Long format options added, though the short ones should still work.
eg. the new "--Counter 0x10" is the same as the old "-C 0x10"
Note this Incompatibility:
Old:
-v displayed verbose debug output
New:
-v and --version simpaly display version
Additional parameters:
-d and --debug display verbose debug output
-h and --help display a help message
Updated turbosat.8 man page accordingly.
Signed-off-by: Len Brown <len.brown@intel.com>
Replaced previously open-coded Package C-state Limit decoding
with table-driven decoding. In doing so, updated to match January 2015
"Intel(R) 64 and IA-23 Architectures Software Developer's Manual".
In the past, turbostat would print package C-state residency columns
for all package states supported by the model's architecture, even though
a particular SKU may not support them, or they may be disabled by the BIOS.
Now turbostat will skip printing colunns if MSRs indicate that they are not enabled.
eg. many SKUs don't support PC7, and so that column will no longer be printed.
Signed-off-by: Len Brown <len.brown@intel.com>
While turbostat is significantly less useful on systems
with no APERF_MSR, it seems more friendly
to run on such systems and report what we can,
rather than refusing to run.
Update man page to reflect recent changes.
Signed-off-by: Len Brown <len.brown@intel.com>
Turbostat can be useful on systems that do not support invariant TSC,
so allow it to run on those systgems.
All arithmetic in turbostat using the TSC value is per-processsor,
so it does not depend on the TSC values being in sync acrosss processors.
Turbostat uses gettimeofday() for the measurement interval
rather than using the TSC directly, so that key metric
is also immune from variable TSC.
Turbostat prints a TSC sanity check column:
TSC_MHz = TSC_delta/interval
If this column is constant and is close to the processor
base frequency, then the TSC is behaving properly.
The other key turbostat columns are calculated this way:
Avg_Mhz = APERF_delta/interval
%Busy = MPERF_delta/TSC_delta
Bzy_MHz = TSC_delta/APERF_delta/MPERF_delta/interval
Tested on Core2 and Core2-Xeon, and so this patch includes
a few other changes to remove the assumption that target
systems are Nehalem and newer.
Signed-off-by: Len Brown <len.brown@intel.com>
The Processor generation code-named Haswell
added MSR_{CORE | GFX | RING}_PERF_LIMIT_REASONS
to explain when and how the processor limits frequency.
turbostat -v
will now decode these bits.
Each MSR has an "Active" set of bits which describe
current conditions, and a "Logged" set of bits,
which describe what has happened since last cleared.
Turbostat currently doesn't clear the log bits.
Signed-off-by: Len Brown <len.brown@intel.com>
For turbostat to run as non-root, it needs to permissions:
1. read access to /dev/cpu/*/msr
via standard user/group/world file permissions
2. CAP_SYS_RAWIO
eg. # setcap cap_sys_rawio=ep turbostat
Yes, running as root still works.
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA commit 8990e73ab2aa15d6a0068b860ab54feff25bee36
Link: https://github.com/acpica/acpica/commit/8990e73a
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpupower tool, when compiled against libcpupower.so fail's to run as
the linker file path's are missing during compilation. So added changes
in the Makefile to run cpupower tool, which helps us run the tool
without doing a 'make install'.
Signed-off-by: Sriram Raghunathan <sriram@marirs.net.in>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
sysfs_get_idlestate_count() returns an unsigned int. Returning -ENODEV
is not the right thing to do here, and in any case is handled the same
way as if there are no states found.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some operations, like frequency-set, need root privileges. However,
the way that this is detected is not correct. The getuid() is called,
while in fact geteuid() should be. This way we can allow
distributions or users to set SETUID flags on the cpupower binary if
they want to and let regular users change the cpu frequency governor.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 16b7c275c0.
My previous commit 16b7c275c0 ("tools: cpupower: fix return checks for
sysfs_get_idlestate_count()") was not correct. After looking
at the changelog for cpupower I noticed that Thomas had changed the return of
sysfs_get_idlestate_count() to an unsigned int to simplify the code. The
problem is really that both he (in his original change) and I (in my new
change) missed the obvious that sysfs_get_idlestate_count()
can't return -ENODEV. It should just return 0 for "no c-states".
Fixes: 16b7c275c0 (tools: cpupower: fix return checks for ...)
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Red Hat and Fedora use a bug reporting tool that gathers data about
"broken" systems called sosreport. Among other things, it includes the
output of 'cpupower idle-info'. Executing 'cpupower idle-info' on a
system that has cpuidle disabled via 'cpuidle.off=1' results in a 300
second hang in the cpupower application.
ie)
[root@intel-brickland-05]# cpupower idle-info
Could not determine cpuidle driver
Analyzing CPU 0:
Number of idle states: -19
[hang]
The problem is that the cpupower code only checks for a zero return from
sysfs_get_idlestate_count(). The function can return -ENODEV (-19) as
above. This patch fixes callers to sysfs_get_idlestate_count() to check
the right return values.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Eliminate an error message for batch-mode processing on unix
systems. ACPICA BZ 1114.
This patch is mainly for fixing the issues of acpiexec which is not in the
Linux upstream.
Link: https://bugs.acpica.org/show_bug.cgi?id=1114
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpidump currently always uses ACPI 2.0 format to dump RSDP, this patch
adds ACPI 1.0 RSDP support.
Link: https://bugs.acpica.org/show_bug.cgi?id=1097
Link: https://bugs.acpica.org/show_bug.cgi?id=1103
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reported-and-tested-by: Rudolf Marek <r.marek@assembler.cz>
Reported-and-tested-by: Rafal <fatwildcat@gmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull idle update from Len Brown:
"Two Intel-platform-specific updates to intel_idle, and a cosmetic
tweak to the turbostat utility"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: tweak whitespace in output format
intel_idle: Broadwell support
intel_idle: Disable Baytrail Core and Module C6 auto-demotion
* pm-tools:
cpupower: Remove redundant error check
cpupower: bench: parse.c: Fix several minor errors
cpupower: mperf monitor: Correct use of ! and &
cpupower: Adjust MAINTAINERS file
PM / tools: cpupower: drop negativity check on unsigned value
Remove double checks, and move the call to print_error to the
first check. Replace break by return, and return 0 on success.
The simplified version of the coccinelle semantic patch that
fixes this issue is as follows:
// <smpl>
@@
expression E; identifier pr; expression list es;
@@
for(...;...;...){
...
- if (E) break;
+ if (E){
+ pr(es);
+ break;
+ }
...
}
- if(E) pr(es);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Resolved several minor errors in prepare_config() and made some additional improvements.
Earlier, the risk of file stream that was not closed. Misuse of strncpy, and the use of strncmp with strlen that makes it pointless.
I also check that sscanf has been successful, otherwise continue to the next line. And minimized the use of magic numbers.
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In commit ae91d60ba8, a bug was fixed that
involved converting !x & y to !(x & y). The code below shows the same
pattern, and thus should perhaps be fixed in the same way.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@@ expression E1,E2; @@
(
!E1 & !E2
|
- !E1 & E2
+ !(E1 & E2)
)
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80621
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some cleanup and comment update.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch is a result of an ACPICA commit to enables acpidump for EFI. For
Linux kernel, this patch is a no-op. It is only required by the ACPICA
release process to reduce the source code differences between the Linux
kernel and the ACPICA upstream. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch reduces the requirement of invoking freopen() in acpidump in order
to reduce the porting effort of acpidump.
This patch achieves this by turning all acpi_os_printf(stdout) into
acpi_ut_file_printf(gbl_output_file). Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The new APIs are enabled to offer a portable layer to access files:
1. acpi_os_XXX_file_XXX: Wrapper of fopen/fclose/fread/fwrite
2. acpi_os_printf: Wrapper of printf
3. acpi_log_error: Wrapper of fprintf(stderr)
This patch deploys such mechanisms to acpidump to improve the portability
of this tool. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch removes exit() from generic acpidump code to improve the
portability of this tool. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds code to use generic OSL for acpidump to improve the
portability of this tool. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch enhances acpi_getopt() by converting the standard C library
invocations into portable ACPI string APIs and acpi_log_error() to improve
portability. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch uses abstract file IO and acpi_log_error() APIs to enhance
cm_get_file_size() so that applications that invoke this API could have
portability improved.
With actual references added to abstract file IO and acpi_log_error(), the
applications need to link oslibcfs.o, utdebug.o, utexcep.o, utmath.o,
utprint.o and utxferror.o.
It is also required to add acpi_os_initialize() invocations if an
application starts to use acpi_log_error().
acpidump has already invoked acpi_os_initialize() in this way. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch enhances ACPI_USAGE_xxx/ACPI_OPTION macros to use portable
acpi_os_printf() so that usage functions for applications no longer rely on
the printf() API.
To use acpi_os_printf() exported by osunixxf.c as a replacement of
printf(), applications need to initialize acpi_gbl_output_file to stdout
and initialize acpi_gbl_db_output_flags to ACPI_DB_CONSOLE_OUTPUT. The
latter is automatically done by ACPI_INIT_GLOBAL(), applications need to
link utglobal.o to utilize this mechanism. For GCC, assigning stdout to
acpi_gbl_output_file using ACPI_INIT_GLOBAL() is not possible as stdout is
not a constant in GCC environment. As an alternative solution, stdout
assignment has been put into acpi_os_initialize(). Thus
acpi_os_initialize() need to be invoked very early by the applications to
initialize the default output of acpi_os_printf() to keep behavior
consistency.
acpidump has already invoked acpi_os_initialize() in this way. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch introduces formatted printing APIs to handle ACPICA specific
formatted print requirements. Currently only specific OSPMs will use this
customized printing support, Linux kernel doesn't use these APIs at this
time. It will be enabled for Linux kernel resident ACPICA after being well
tested. So currently this patch is a no-op.
The specific formatted printing APIs are useful to ACPICA as:
1. Some portable applications do not link standard C library, so they
cannot use standard formatted print APIs directly.
2. Platform specific printing format may differ and thus not portable, for
example, u64 is %ull for Linux kernel and is %uI64 for some MSVC
versions.
3. Platform specific printing format may conflict with ACPICA's usages
while it is not possible for ACPICA developers to test their code for
all platforms. For example, developers may generate %pRxxx while Linux
kernel treats %pR as structured resource printing and decodes variable
argument as a "struct resource" pointer.
This patch solves above issues by introducing the new APIs.
Note that users of such APIs are not introduced in this patch. Users of
acpi_os_file_vprintf()/acpi_ut_file_printf() need to invoke acpi_os_initialize(),
this should be taken care by the further patches where such users are
introduced. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds portable file IO to generic OSL to improve the portability
of the applications.
A portable application may use different file IO interfaces than the
standard C library ones. This patch thus introduces an abstract file IO
layer into the generic OSL.
Note that this patch does not introduce users of such interfaces, further
patches should introduce users one by one carefully with build tests
performed. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch is mainly for acpidump where there are redundant
acpi_os_printf()/acpi_os_vprintf() stubs implemented. This patch cleans up such
specific implementation by linking acpidump to osunixxf.c/oswinxf.c.
To make acpi_os_printf() exported by osunixxf.c/oswinxf.c to behave as the
old acpidump specific ones, applications need to:
1. Initialize acpi_gbl_db_output_flags to ACPI_DB_CONSOLE_OUTPUT.
This is automatically done by ACPI_INIT_GLOBAL(), applications need to
link utglobal.o to utilize this mechanism.
2. Initialize acpi_gbl_output_file to stdout.
For GCC, assigning stdout to acpi_gbl_output_file using ACPI_INIT_GLOBAL()
is not possible as stdout is not a constant in GCC environment. As an
alternative solution, stdout assignment is put into acpi_os_initialize().
Thus acpi_os_initialize() need to be invoked very early by the
applications to initialize the default output of acpi_os_printf().
This patch also releases osunixxf.c to the Linux kernel. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The utglobal.c is used to define and initialize global variables. It makes
sense if just adding utglobal.o to applications that are using such
variables. But acpi_ut_init_globals() is preventing us from doing so as
this initialization function references other components' initializations
code, which leads to the requirement that many files should also get linked
if one wants to link utglobal.o.
It is possible to just move acpi_ut_init_global() to utinit.c for
applications that require this function to link.
By linking utglobal.o, we can stop defining DEFINE_ACPI_GLOBALS for
applications (currently only acpidump is affected). Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For older EFI platforms, searches for the RSDP using ACPI 1.0 GUID if the
2.0 GUID search fails.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-tools:
ACPI / tools: Introduce ec_access.c - tool to access the EC
* pm-tools:
cpupower: Remove mc and smt power aware scheduler info/settings
cpupower: cpupower info -b should return 0 on success, not the perf bias value
cpupower: If root, try to load msr driver on x86 if /dev/cpu/0/msr is not available
cpupower: Install recently added cpupower-idle-{set, info} manpages
cpupower: Introduce idle state disable-by-latency and enable-all
cpupower: Remove all manpages on make uninstall
cpupower: Remove dead link to homepage, and update the targets built.
cpupower: Rename cpufrequtils -> cpupower, and libcpufreq -> libcpupower.
PM / tools: cpupower: add option to display values without round offs
tools / power: turbostat: Drop temperature checks
* pm-cpufreq: (28 commits)
cpufreq: handle calls to ->target_index() in separate routine
cpufreq: s5pv210: drop check for CONFIG_PM_VERBOSE
cpufreq: intel_pstate: Remove unused member name of cpudata
cpufreq: Break out early when frequency equals target_freq
cpufreq: Tegra: drop wrapper around tegra_update_cpu_speed()
cpufreq: imx6q: Remove unused include
cpufreq: imx6q: Drop devm_clk/regulator_get usage
cpufreq: powernow-k8: Suppress checkpatch warnings
cpufreq: powernv: make local function static
cpufreq: Enable big.LITTLE cpufreq driver on arm64
cpufreq: nforce2: remove DEFINE_PCI_DEVICE_TABLE macro
intel_pstate: Add CPU IDs for Broadwell processors
cpufreq: Fix build error on some platforms that use cpufreq_for_each_*
PM / OPP: Move cpufreq specific OPP functions out of generic OPP library
PM / OPP: Remove cpufreq wrapper dependency on internal data organization
cpufreq: Catch double invocations of cpufreq_freq_transition_begin/end
intel_pstate: Remove sample parameter in intel_pstate_calc_busy
cpufreq: Kconfig: Fix spelling errors
cpufreq: Make linux-pm@vger.kernel.org official mailing list
cpufreq: exynos: Use dev_err/info function instead of pr_err/info
...
In "-n" mode, reserved tables (RSDP/RSDT/XSDT/DSDT/FACS) are dumped
multiple times due a missing instance check in osl_get_bios_table().
This patch fixes this issue.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These kernel interfaces got removed by:
commit 8e7fbcbc22
Author: Peter Zijlstra <peterz@infradead.org>
Date: Mon Jan 9 11:28:35 2012 +0100
sched: Remove stale power aware scheduling remnants and dysfunctional knobs
No need to further keep them as userspace configurations.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is reported that there are buggy BIOSes in the world: AMI uses an XSDT
compiler for early BIOSes, this compiler will generate XSDT with a NULL
entry. The affected BIOS versions are "AMI BIOS F2-F4".
Original solution on Linux is to use an alternative heathy root table
instead of the ill one. This commit is:
Commit: 671cc68dc6
Subject: ACPICA: Back port and refine validation of the XSDT root table.
This is an example of such XSDT dumped from B85-HD3 (AMI F3 BIOS):
[000h 0000 4] Signature : "XSDT" [Extended System Description Table]
[004h 0004 4] Table Length : 00000074
[008h 0008 1] Revision : 01
[009h 0009 1] Checksum : 18
[00Ah 0010 6] Oem ID : "ALASKA"
[010h 0016 8] Oem Table ID : "A M I"
[018h 0024 4] Oem Revision : 01072009
[01Ch 0028 4] Asl Compiler ID : "AMI "
[020h 0032 4] Asl Compiler Revision : 00010013
[024h 0036 8] ACPI Table Address 0 : 00000000BA5F8180
[02Ch 0044 8] ACPI Table Address 1 : 00000000BA5F8290
[034h 0052 8] ACPI Table Address 2 : 00000000BA5F8308
[03Ch 0060 8] ACPI Table Address 3 : 00000000BA5F8848
[044h 0068 8] ACPI Table Address 4 : 00000000BA5F9320
[04Ch 0076 8] ACPI Table Address 5 : 00000000BA5F9360
[054h 0084 8] ACPI Table Address 6 : 00000000BA5F9398
[05Ch 0092 8] ACPI Table Address 7 : 00000000BA5F9708
[064h d100 8] ACPI Table Address 8 : 00000000BA5FC9A8
[06Ch 0108 8] ACPI Table Address 9 : 0000000000000000
But according to the bug report, the XSDT in fact is not broken. In the
above XSDT, ACPI Table Address 1-8 contains the same value as RSDT. The
differences can only be seen on the following 2 entries:
1. The first entry points to a FADT whose Revision is 5 while the first
entry in RSDT points to a FADT whose Revision is 2.
The FADT dumped from the address indicated by the first entry of XSDT:
FACP @ 0x00000000BA5F8180
0000: 46 41 43 50 0C 01 00 00<05>4B 41 4C 41 53 4B 41 FACP.....KALASKA
...
The FADT dumped from the address indicated by the first entry of RSDT:
FACP @ 0x00000000BA5ED0F0
0000: 46 41 43 50 84 00 00 00<02>A7 41 4C 41 53 4B 41 FACP......ALASKA
...
2. The last entry is a NULL terminator.
According to the test result, the Revision 5 FADT is accessible. Thus the
original solution turns out to be a work around that is preventing the
higher revision tables to be used for such platforms (they are all x86-64
platforms, and should use XSDT and higher revision FADT).
This patch offers a new solution, where a sanity check is performed before
installing a table address from XSDT. If the entry is NULL, it is simply
discarded.
Note that, this patch doesn't remove the original solution, so for Linux
kernel, this commit is actually a no-op, but it allows acpidump to be
working on such platforms. By doing so, we allow another easy revertable
commit to enable this feature so that when that commit is reverted, the
useful sanity check will not be affected. Lv Zheng.
References: https://bugzilla.kernel.org/show_bug.cgi?id=73911
References: https://bugs.archlinux.org/task/39811
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reported-and-tested-by: Bruce Chiarelli <mano155@gmail.com>
Reported-and-tested-by: Spyros Stathopoulos <spystath@gmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds "-x" and "-x -x" options to disable XSDT for acpidump.
The single "-x" can be used to stop using XSDT, RSDT will be forced to find
static tables, note that XSDT will still be dumped. The double "-x" can
stop dumping XSDT, which is useful when the XSDT address reported by RSDP
is pointing to an invalid address.
It is reported there are platforms having broken XSDT shipped, acpidump
will stop working while accessing such XSDT. This patch adds new option so
that users can force acpidump to dump tables listed in the RSDT. Lv Zheng.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=73911
Buglink: https://bugs.archlinux.org/task/39811
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reported-and-tested-by: Bruce Chiarelli <mano155@gmail.com>
Reported-and-tested-by: Spyros Stathopoulos <spystath@gmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch enforces a rule to always use ACPI_VALIDATE_RSDP_SIG for RSDP
signatures passed from table header or ACPI_SIG_RSDP so that truncated
string comparison can be avoided. This could help to fix the issue that
"RSD " matches but "RSD PTR " doesn't match. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes an issue that the while loop is not needed as fread()
should return exact the bytes of expected.
The patch is tested by runing diff against the output of "-c" mode and
the normal mode, and only finds the following differences:
1. table addresses: the "-c" mode will always fill 0x0000000000000000 for
the address.
2. RSDP/RSDT/XSDT: there is no generation of such tables for "-c" mode.
So the test result shows the fix is valid. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The command "cpupower frequency-info" can be used when using cpupower to
monitor and test processor behaviour to determine if the processor is
behaving as expected. This data can be compared to the output of
/proc/cpuinfo or the output of
/sys/devices/system/cpu/cpuX/cpufreq/scaling_available_frequencies
to determine if the cpu is in an expected state.
When doing this I noticed comparison test failures due to the way the
data is displayed in cpupower. For example,
[root@intel-s3e37-02 cpupower]# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies
2262000 2261000 2128000 1995000 1862000 1729000 1596000 1463000 1330000
1197000 1064000
compared to
[root@intel-s3e37-02 cpupower]# cpupower frequency-info
analyzing CPU 0:
driver: acpi-cpufreq
CPUs which run at the same hardware frequency: 0
CPUs which need to have their frequency coordinated by software: 0
maximum transition latency: 10.0 us.
hardware limits: 1.06 GHz - 2.26 GHz
available frequency steps: 2.26 GHz, 2.26 GHz, 2.13 GHz, 2.00 GHz, 1.86 GHz, 1.73 GHz, 1.60 GHz, 1.46 GHz, 1.33 GHz, 1.20 GHz, 1.06 GHz
available cpufreq governors: conservative, userspace, powersave, ondemand, performance
current policy: frequency should be within 1.06 GHz and 2.26 GHz.
The governor "performance" may decide which speed to use
within this range.
current CPU frequency is 2.26 GHz (asserted by call to hardware).
boost state support:
Supported: yes
Active: yes
shows very different values for the available frequency steps. The cpupower
output rounds off values at 2 decimal points and this causes problems with
test scripts. For example, with the data above,
1.064 is 1.06
1.197 is 1.20
1.596 is 1.60
1.995 is 2.00
2.128 is 2.13
and most confusingly,
2.261 is 2.26
2.262 is 2.26
Truncating these values serves no real purpose other than making the output
pretty. Since the default has been to round off these values I am adding
a -n/--no-rounding option to the cpupower utility that will display the
data without rounding off the still significant digits.
After patch,
analyzing CPU 0:
driver: acpi-cpufreq
CPUs which run at the same hardware frequency: 0
CPUs which need to have their frequency coordinated by software: 0
maximum transition latency: 10.000 us.
hardware limits: 1.064000 GHz - 2.262000 GHz
available frequency steps: 2.262000 GHz, 2.261000 GHz, 2.128000 GHz, 1.995000 GHz, 1.862000 GHz, 1.729000 GHz, 1.596000 GHz, 1.463000 GHz, 1.330000 GHz, 1.197000 GHz, 1.064000 GHz
available cpufreq governors: conservative, userspace, powersave, ondemand, performance
current policy: frequency should be within 1.064000 GHz and 2.262000 GHz.
The governor "performance" may decide which speed to use
within this range.
current CPU frequency is 2.262000 GHz (asserted by call to hardware).
boost state support:
Supported: yes
Active: yes
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Intel 64 and IA-32 Architectures Software Developer's Manual says
that TjMax is stored in bits 23:16 of MSR_TEMPERATURE TARGET (0x1a2).
That's 8 bits, not 7, so it must be masked with 0xFF rather than 0x7F.
The manual has no mention of which values should be considered valid,
which kind of implies that they all are. Arbitrarily discarding values
outside a specific range is wrong. The upper range check had to be
fixed recently (commit 144b44b1) and the lower range check is just as
wrong. See bug #75071:
https://bugzilla.kernel.org/show_bug.cgi?id=75071
There are many Xeon processor series with TjMax of 70, 71 or 80
degrees Celsius, way below the arbitrary 85 degrees Celsius limit.
There may be other (past or future) models with even lower limits.
So drop this arbitrary check. The only value that would be clearly
invalid is 0. Everything else should be accepted.
After these changes, turbostat is aligned with what the coretemp
driver does.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Len Brown <len.brown@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There has been confusion all the time about which mailing list to follow
for cpufreq activities, linux-pm@vger.kernel.org or cpufreq@vger.kernel.org.
Since patches sent to cpufreq@vger.kernel.org don't go to Patchwork
which is a maintenance workflow problem, make linux-pm@vger.kernel.org
the official mailing list for cpufreq stuff and remove all references
of cpufreq@vger.kernel.org from kernel source.
Later, we can request that the list be dropped entirely.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This userspace tool accesses the EC through the ec_sys debug driver
(through /sys/kernel/debug/ec/ec0/io).
The EC command/data registers cannot be accessed directly, because they
may be manipulated by the AML interpreter in parallel.
The ec_sys driver synchronizes user space (debug) access with the AML
interpreter.
Signed-off-by: Thomas Renninger <trenn@suse.de>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- bindir is created, but sbindir is used -> fix that
- the debug parts are there twice (copy paste bug?). Remove one of the
exact same parts
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch updates man file of acpidump.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch updates tools Makefile to use new acpidump.
ACPICA's acpidump relies on various ACPICA components/common/os_specific
source code. They are located in various kernel folders, being searched
and compiled using vpath technique in Makefile. These files include:
1. drivers/acpi/acpica/acapps.h
2. tools/power/acpi/common/getopt.c
3. tools/power/acpi/common/cmfsize.c
4. tools/power/acpi/os_specific/service_layers/oslinuxtbl.c
5. tools/power/acpi/os_specific/service_layers/osunixdir.c
6. tools/power/acpi/os_specific/service_layers/osunixmap.c
This patch has been tested on DELL Inspiron Mini, acpidump output can be
successfully generated by typing the following commands:
# cd tools/power/acpi
# make DEBUG=false
# sudo make install DESTDIR=/opt
# sudo make uninstall DESTDIR=/opt
# make clean
Or
# cd tools
# make acpi
# sudo make acpi_install
# sudo make acpi_uninstall
# make acpi_clean
A kernel build test is also performed on DELL Inspiron Mini to verify that
the changes done to actypes.h and aclinux.h won't affect the kernel
build process.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch is the generation of a commit that updates release automation
with newly added structures and files that are referenced by the acpidump.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpidump is initiated by Bob Moore and Chao Guan, fixed and completed
by Lv Zheng.
This patch is a generation of the commit that adds acpidump release
automation into ACPICA release process. Lv Zheng.
Note that this patch doesn't replace the kernel shipped acpidump with the
new acpidump. The replacement is done by further patches.
Original-by: Chao Guan <guanchao@mail.ustc.edu.cn>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use 8 columns for each number ouput.
We don't fit into 80 columns on most machines,
so keep the format simple.
Print frequency in MHz instead of GHz.
We've got 8 columns now, so use them to
show low frequency in a more natural unit.
Many users didn't understand what %c0 meant,
so re-name it to be %Busy.
Add Avg_MHz column, which is the frequency that many
users expect to see -- the total number of cycles executed
over the measurement interval.
People found the previous GHz to be confusing, since
it was the speed only over the non-idle interval.
That measurement has been re-named Bzy_MHz.
Suggested-by: Dirk J. Brandewie
Signed-off-by: Len Brown <len.brown@intel.com>
