Call regulator_[get|set]_voltage_sel_regmap instead of open code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Ying-Chun Liu <paulliu@debian.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
By setting linear_min_sel to anatop_reg->min_bit_val, we can avoid
adjust the anatop_reg->min_bit_val offset in [set|get]_voltage_sel.
With this chance we can refactor this driver to use
regulator_[get|set]_voltage_sel_regmap.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Ying-Chun Liu <paulliu@debian.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is required since commit f7df20ec32
"regulator: core: Use list_voltage() to read single voltage regulators",
otherwise _regulator_get_voltage returns rdev->desc->ops->list_voltage(rdev, 0).
The Maxim 1586 controls V3 and V6 voltages, but offers no way of reading back
the set up value. Thus this patch caches the setting when setting new voltage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Simply use devm_gpio_request_one() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To clear the mask bit, setting data argument to be 0 with proper mask setting
for lp8788_update_bits. We don't need the var array here.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use of_match_ptr and add ifdef CONFIG_OF guard for regulator_gpio_of_match.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce a regulator_can_change_voltage() function for the subsytems or
drivers which might check if applying voltage change is possible and use
special workaround code when the driver is used with fixed regulators or
regulators with disabled ability to change the voltage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver can be converted to use linear_min_sel and
regulator_[map|list]_voltage_linear.
Below shows the equation (from Datasheet) for each LDOs.
For AUTOOUT:
VO(prog) = 0.625 + auto_out x 0.025 V; e.g.
(00000000 to 00101110: reserved)
00101111: 1.8 V (min)
01010011: 2.7 V
01101010: 3.275 V
01101011: 3.300 V
01101100: 3.325 V
01111111 : 3.800 V (max)
The linear mapping start from 0x2f selector.
Thus we convert this equation to:
VO(prog) = 1.8 + (selector - linear_min_sel) x 0.025 V
(min_uV = 1800000, uV_step = 25000, linear_min_sel = 0x2f)
For DOWNxOUT:
VO(prog) = 0.625 + downx_out x 0.025 V; e.g.
00000000 : 0.625 V (min)
00010111 : 1.200 V
00101111 : 1.800 V
01011111 : 3.000 V (max)
For xLDOOUT:
VO(prog) = 0.9 + xldo_out x 0.1 V; e.g.
00000: 0.9 V
00001: 1.0 V
11000 : 3.3 V
11011 : 3.6 V
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some Arizona devices such as the WM5102 can use DVFS on their digital core,
for these devices allow the voltage range to vary in the default setup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Below equation means the "voltage" is the "smallest" voltage within specific
range.
ret = DIV_ROUND_UP(min - bottom) / step;
voltage = ret * step + bottom;
If we do try 1 down when (voltage > max), new voltage is then less than min
voltage. Which means the new voltage is not in the requested voltage range.
This patch also includes below cleanups:
- Use DIV_ROUND_UP
- rename variable 'ret' to 'sel' for better readability because as3711_sel_check
returns the selector.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Below cases are supposed to be valid:
min_uV == max_uV == info->max_uV
min_uV == max_uV == rdev->desc->min_uV
Don't return -EINVAL for above cases.
This patch also includes below cleanups:
- Use rdev_get_drvdata(rdev) instead of rdev->reg_data.
- Remove unnecessary WARN_ON, it looks pointless.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Checking da9052_current_limits[row][i] <= max_uA is not enough, it is possible
da9052_current_limits[row][i] may less than the requested min_uA.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Selecting the minimal value is only true for voltage regulators.
For current regulators the maximum in the given range should be
selected instead.
This issue was reported by Heiko Stuebner for gpio-regulator driver [1],
and the conclusion is to select the max current for current regulators [2].
[1] https://lkml.org/lkml/2012/8/5/162
[2] https://lkml.org/lkml/2012/8/6/183
This patch also ensures da9055_buck_set_current_limit return -EINVAL when the
supported current limit does not meet the request range.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When tps->enable_pwm_dvfs is true, write to TPS51632_VOLTAGE_BASE_REG rather
than TPS51632_VOLTAGE_SELECT_REG.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some drivers (at least 3 drivers) have such variant of linear mapping that
the first few selectors are invalid and the reset are linear mapping.
Let's support this case in core.
This patch adds linear_min_sel in struct regulator_desc,
so we can allow specific minimal selector for starting linear mapping.
Then extends regulator_[map|list]_voltage_linear() to support this feature.
Note that for selectors less than min_linear_index, we need count them to
n_voltages so regulator_list_voltage() won't fail while checking the boundary
for selector before calling list_voltage callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add device tree based discovery support for max8997.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull powerpc EEH bugfixes from Benjamin Herrenschmidt.
Two one-liner fixes for the new EEH code.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/eeh: Do not invalidate PE properly
powerpc/pseries: Fix oops with MSIs when missing EEH PEs
Pull MIPS fixes from Ralf Baechle:
"Three issues fixed accross the field:
- Some functions that were recently outlined as part of a preemption
fix were causing problems with function tracing.
- The recently merged in-kernel MPI library uses very outdated
headers that contain MIPS-specific code which won't build on with
gcc 4.4 or newer.
- The MIPS non-NUMA memory initialization was making only a very
half-baked attempt at merging adjacent memory ranges. This kept
the code simple enough but is now causing issues with kexec."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
While the EEH does recovery on the specific PE that has PCI errors,
the PCI devices belonging to the PE will be removed and the PE will
be marked as invalid since we still need the information stored in
the PE. We only invalidate the PE when it doesn't have associated
EEH devices and valid child PEs. However, the code used to check
that is wrong. The patch fixes that.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Only a single commit for fixing the build error without CONFIG_PM
in hda driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=9jnO
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound build error fix from Takashi Iwai:
"Only a single commit for fixing the build error without CONFIG_PM in
hda driver."
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix build without CONFIG_PM
In case the gpio based volatage selection mode is not used for either of
buck 1/2/5, then only the BUCKxDVS1 register need to be programmed. So
determine whether dvs mode is used and limit the loop count appropriately.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The BUCKxDVSx register programming is now moved prior to setting up of the
gpio based dvs mode. This will ensure that all the BUCKxDVSx registers
are programmed with appropriate voltage values before the gpio based dvs
mode is selected for buck1/2/5.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
