These APIs aren't used, so remove them. This can be reverted if
we get a user at some point.
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Suggested-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* clk-iproc:
clk: iproc: define Broadcom NS2 iProc clock binding
clk: iproc: define Broadcom NSP iProc clock binding
clk: ns2: add clock support for Broadcom Northstar 2 SoC
clk: iproc: Separate status and control variables
clk: iproc: Split off dig_filter
clk: iproc: Add PLL base write function
clk: nsp: add clock support for Broadcom Northstar Plus SoC
clk: iproc: Add PWRCTRL support
clk: cygnus: Convert all macros to all caps
ARM: cygnus: fix link failures when CONFIG_COMMON_CLK_IPROC is disabled
Document the device tree bindings for Broadcom Northstar 2 architecture
based clock controller
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Document the device tree bindings for Broadcom Northstar Plus
architecture based clock controller
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Broadcom Northstar 2 SoC is architected under the iProc
architecture. It has the following PLLs: GENPLL SCR, GENPLL SW,
LCPLL DDR, LCPLL Ports, all derived from an onboard crystal.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some PLLs have separate registers for Status and Control. The means the
pll_base needs to be split into 2 new variables, so that those PLLs can
specify device tree registers for those independently. Also, add a new
driver flag to identify this presence of the split, and let the driver
know that additional registers need to be used.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The PLL loop filter/gain can be located in a separate register on some
SoCs. Split these off into a separate variable, so that an offset can
be added if necessary. Also, make the necessary modifications to the
Cygnus and NSP drivers for this change.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
All writes to the PLL base address must be flushed if the
IPROC_CLK_NEEDS_READ_BACK flag is set. If we add a function to make the
necessary write and reads, we can make sure that any future code which
makes PLL base writes will do the correct thing.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Broadcom Northstar Plus SoC is architected under the iProc
architecture. It has the following PLLs: ARMPLL, GENPLL, LCPLL0, all
derived from an onboard crystal.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some iProc SoC clocks use a different way to control clock power, via
the PWRDWN bit in the PLL control register. Since the PLL control
register is used to access the PWRDWN bit, there is no need for the
pwr_base when this is being used. A new flag, IPROC_CLK_EMBED_PWRCTRL,
has been added to identify this usage. We can use the AON interface to
write the values to enable/disable PWRDOWN.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
[sboyd@codeaurora.org: Remove useless parentheses]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The macros that are being used to initialize the values of the clk
structures should be all caps. Find and replace all of them with their
relevant counterparts.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When CONFIG_CYGNUS is set but CONFIG_COMMON_CLK_IPROC is disabled, the
following link failures are caused:
drivers/built-in.o: In function `cygnus_armpll_init':
:(.init.text+0x1d290): undefined reference to `iproc_armpll_setup'
drivers/built-in.o: In function `cygnus_genpll_clk_init':
:(.init.text+0x1d2c4): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_lcpll0_clk_init':
:(.init.text+0x1d304): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_mipipll_clk_init':
:(.init.text+0x1d344): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_asiu_init':
:(.init.text+0x1d370): undefined reference to `iproc_asiu_setup'
It is fixed it by always selecting COMMON_CLK_IPROC from
ARCH_BCM_IPROC, and making COMMON_CLK_IPROC a silent option (thus
preventing it from being erroneously disabled by a user).
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- Support for the Audio PLL and child clocks
- Support for the A33 AHB gates
- New clk-multiplier generic driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WtVW
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Pull Allwinner clock additions for 4.4 from Maxime Ripard:
- Support for the Audio PLL and child clocks
- Support for the A33 AHB gates
- New clk-multiplier generic driver
* tag 'sunxi-clocks-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi: mod1 clock support
clk: sunxi: codec clock support
clk: sunxi: pll2: Add A13 support
clk: sunxi: Add a driver for the PLL2
clk: Add a basic multiplier clock
clk: sunxi: Add A33 gates support
for_each_compatible_node performs an of_node_get on each iteration, so a
break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e;
@@
for_each_compatible_node(n,...) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
for_each_compatible_node performs an of_node_get on each iteration, so a
break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e;
@@
for_each_compatible_node(n,...) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
The resulting puts were manually moved to the end of the function for
conciseness.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
for_each_matching_node_and_match performs an of_node_get on each iteration,
so a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression e1,e2,e;
local idexpression np;
@@
for_each_matching_node_and_match(np, e1, e2) {
... when != of_node_put(np)
when != e = np
(
return np;
|
+ of_node_put(np);
? return ...;
)
...
}
// </smpl>
Besides the problem identified by the semantic patch, this patch adds an
of_node_get in front of saving np in a field of parent, to account for the
fact that this value will be put on going on to the next element in the
iteration, and then adds of_node_puts in the two loops where the parent
pointer can be freed.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The module 1 type of clocks consist of a gate and a mux and are used on
the audio blocks to mux and gate the PLL2 outputs for AC97, IIS or
SPDIF. This commit adds support for them on the sunxi clock driver.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
The codec clock on sun4i, sun5i and sun7i is a simple gate with PLL2 as
parent. Add a driver for such a clock.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
The A13, unlike the A10 and A20, doesn't use a pass-through exception for
the 0 value in the pre and post dividers, but increments all the values
written in the register by one.
Add an exception for both these cases to handle them nicely.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
The PLL2 on the A10 and later SoCs is the clock used for all the audio
related operations.
This clock has a somewhat complex output tree, with three outputs (2X, 4X
and 8X) with a fixed divider from the base clock, and an output (1X) with a
post divider.
However, we can simplify things since the 1X divider can be fixed, and we
end up by having a base clock not exposed to any device (or at least
directly, since the 4X output doesn't have any divider), and 4 fixed
divider clocks that will be exposed.
This clock seems to have been introduced, at least in this form, in the
revision B of the A10, but we don't have any information on the clock used
on the revision A.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Some clocks are using a multiplier component, however, unlike their mux,
gate or divider counterpart, these factors don't have a basic clock
implementation.
This leads to code duplication across platforms that want to use that kind
of clocks, and the impossibility to use the composite clocks with such a
clock without defining your own rate operations.
Create such a driver in order to remove these issues, and hopefully factor
the implementations, reducing code size across platforms and consolidating
the various implementations.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
This patch affects the clocks that use fractional ndivider in their
PLL output frequency calculation. Instead of 2^20 divide factor, the
clock's ndiv integer shift was used. Fixed the bug by replacing ndiv
integer shift with 2^20 factor.
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Fixes: 5fe225c105 ("clk: iproc: add initial common clock support")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The clocks' properties have been already properly set, so there's no
need to set this flag for sdio0 and sdio1 clk any more.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Since we have added the necessary two clks' properties in dts, we can
remove the "sdio" clk's CLK_IGNORE_UNUSED flag now.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Add all R-Car H3 Clock Pulse Generator Core Clock Outputs, as listed in
Table 8.2a ("List of Clocks [R-Car H3]") of the R-Car Gen3 datasheet
(rev. 0.5E).
Note that internal CPG clocks (S0, S1, S2, S3, SDSRC, SSPSRC, and
RPCSRC) are not included, as they're used as internal clock sources
only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Magnus Damm <damm+renesas@opensource.se>
On Renesas ARM SoCs (SH/R-Mobile, R-Car, RZ), the CPG (Clock Pulse
Generator) and MSSR (Module Standby and Software Reset) blocks are
intimately connected, and share the same register block.
Hence it makes sense to describe these two blocks using a
single device node in DT, instead of using a hierarchical structure with
multiple nodes, using a mix of generic and SoC-specific bindings.
These new DT bindings are intended to replace the existing DT bindings
for CPG core clocks ("renesas,*-cpg-clocks", "renesas,cpg-div6-clock")
and module clocks ("renesas,*-mstp-clocks"), at least for new SoCs.
This will make it easier to add module reset support later, which is
currently not implemented, and difficult to achieve using the existing
bindings due to the intertwined register layout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Magnus Damm <damm+renesas@opensource.se>
This contains a patch that allows the DFLL to use clock rates higher
than 2^31-1 Hz by using the ->determine_rate() operation instead of the
->round_rate() operation. Other than that there's a couple of cleanups
in preparation for Tegra210 support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4qKy
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.4-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.4-rc1
This contains a patch that allows the DFLL to use clock rates higher
than 2^31-1 Hz by using the ->determine_rate() operation instead of the
->round_rate() operation. Other than that there's a couple of cleanups
in preparation for Tegra210 support.
tegra_audio_clk_init was written expecting a single PLL to be
passed in directly. Change this to accept an array which will
allow for supporting multiple plls and specifying specific data
about them, like their parent, which may change over time.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Benson Leung pointed out that the kerneldoc for this structure has
become stale. Update the field descriptions to match the structure
content.
Reported-by: Benson Leung <bleung@chromium.org>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some fields moved from the tegra_clk_pll struct to the tegra_pll_params
struct. Update the struct comments to reflect where the fields really
are.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The monitor code is used with DEBUG_FS only, so move it into the
corresponding #ifdef block to avoid potential compiler warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This reverts commit e79b202c63.
Now that we use of_clk_get() inside of_clk_get_parent_name() we
can safely use it here.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add rcg and branch clk structs for DSI1 and DSI2 blocks found in MSM8960
and APQ8064. Each DSI instance has 4 pairs of rcg and branch clocks.
Populate arrays mmcc_msm8960_clks and mmcc_apq8064_clks with these clocks.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
DSI specific RCG clocks required customized clk_ops. There are
a total of 4 RCGs per DSI block: DSI, BYTE, ESC and PIXEL.
There are a total of 2 clocks coming from the DSI PLL, which serve as
inputs to these RCGs. The BYTE and ESC RCGs are fed by one of the
post dividers of DSI1 or DSI2 PLLs, and the DSI and PIXEL RCGs are fed by
another divider of the PLL.
In each of the 2 groups above, only one of the clocks sets its parent.
These are BYTE RCG and DSI RCG for each of the groups respectively, as
shown in the diagram below.
The DSI and BYTE RCGs serve as bypass clocks. We create a new set of ops
clk_rcg_bypass2_ops, which are like the regular bypass ops, but don't
take in a freq table, since the DSI driver using these clocks is
parent-able.
The PIXEL RCG needs to derive the required pixel clock using dsixpll.
It parses a m/n frac table to retrieve the correct clock.
The ESC RCG doesn't have a frac M/N block, it can just apply a pre-
divider. Its ops simply check if the required clock rate can be
achieved by the pre-divider.
+-------------------+
| |---dsixpllbyte---o---> To byte RCG
| | | (sets parent rate)
| | |
| | |
| DSI 1/2 PLL | |
| | o---> To esc RCG
| | (doesn't set parent rate)
| |
| |----dsixpll-----o---> To dsi RCG
+-------------------+ | (sets parent rate)
( x = 1, 2 ) |
|
o---> To pixel rcg
(doesn't set parent rate)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These drivers only have runtime but no build time dependencies so can be
built for testing purposes if the Kconfig COMPILE_TEST option is enabled.
This is useful to have more build coverage and make sure that drivers are
not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When calling __clk_get_name() on a const clock:
warning: passing argument 1 of '__clk_get_name' discards 'const' qualifier from pointer target type
include/linux/clk-provider.h:613:13: note: expected 'struct clk *' but argument is of type 'const struct clk *'
__clk_get_name() does not modify the passed clock, hence make it const.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
r8a7778_rates[] and r8a7778_divs[] are only used in clk-r8a7778.c, and
never modified.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- A couple of fixes on i.MX31 and i.MX35 clock initialization functions
which makes mxc_timer_init() currently be called twice for DT boot.
- Increase i.MX6UL AXI bus clock rate to 264MHz which is the optimal
design target.
- Add a few missing clocks, ADC clock for i.MX7D, OCOTP clock for
Vybrid, and SPDIF_GCLK for i.MX6.
- A series from Lucas to fix early debug UART clock setup. This is
currently a one-off fix for i.MX platform, and can be extended to
become a generic solution later.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWIRFyAAoJEFBXWFqHsHzOE7wH/25WaamOOOL3vGVCBeIs2+aB
nibCEKCPGu2/b1YN+BEQMlh+K7d59Ogd0xVtTkLEGhIBW+LF5zDpsd6jNl7Ts6PQ
5w3gG7K/NqPzIXlgo+z5Oa4UI1DlDemcA1xihR+hFWjLQb8DBmnusK52ctS5MLfP
6SoepDWHJvtuAfoL/3ytNTi/xCW12sEVkzRV7QbG9GV2UmUgF2AVWKBkH+c28vnP
dyt2Cyrr4+9ov6p0k0OJnHDv1AxkkNlHh0G33pZMZmnqcn/ZagmdH2GReGWZi6PM
XLMY/piEK7zzryJ51hL9AGZi7so1LWs27kBtYo9r7bN9/cG4kaENGw6Du1jEf4I=
=OBCO
-----END PGP SIGNATURE-----
Merge tag 'imx-clk-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-next
Pull i.MX updates from Shawn Guo:
"The i.MX clock updates for 4.4:
- A couple of fixes on i.MX31 and i.MX35 clock initialization functions
which makes mxc_timer_init() currently be called twice for DT boot.
- Increase i.MX6UL AXI bus clock rate to 264MHz which is the optimal
design target.
- Add a few missing clocks, ADC clock for i.MX7D, OCOTP clock for
Vybrid, and SPDIF_GCLK for i.MX6.
- A series from Lucas to fix early debug UART clock setup. This is
currently a one-off fix for i.MX platform, and can be extended to
become a generic solution later."
* tag 'imx-clk-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx6: Add SPDIF_GCLK clock in clock tree
clk: imx7d: add ADC root clock
clk: imx31: Do not call mxc_timer_init twice when booting with DT
clk: imx7d: retain early UART clocks during kernel init
clk: imx6: retain early UART clocks during kernel init
clk: imx5: retain early UART clocks during kernel init
clk: imx35: retain early UART clocks during kernel init
clk: imx31: retain early UART clocks during kernel init
clk: imx27: retain early UART clocks during kernel init
clk: imx25: retain early UART clocks during kernel init
clk: imx: add common logic to detect early UART usage
clk: imx35: Do not call mxc_timer_init twice when booting with DT
clk: clk-vf610: Add clock for Vybrid OCOTP controller
clk: imx: increase AXI clock rate to 264MHz for i.MX6UL
If a clock provider has #clock-cells = 1 and we call
of_clk_get_parent_name() on it we may end up returning the name
of the provider node if the provider doesn't have a
clock-output-names property. This doesn't make sense, especially
when you consider that calling of_clk_get_parent_name() on such a
node with different indices will return the same name each time.
Let's try getting the clock from the framework via of_clk_get()
instead, and only fallback to the node name if we have a provider
with #clock-cells = 0. This way, we can't hand out the same name
for different clocks when we don't actually know their names.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The email address listed in MODULE_AUTHOR() no longer exist so to prevent
people to send emails to the old address, replace it with my current one.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This partially reverts commit eca61c9ff2.
Thomas reports that it causes regressions on Armada XP devices.
This is because of_clk_get_parent_name() relies on the property
'clock-output-names' to resolve the name of a clock's parent,
without trying to get the clock from the framework and call
__clk_get_name(). Given that Armada XP devices don't have the
'clock-output-names' property, of_clk_get_parent_name() returns
the name of the node which doesn't match the actual parent
clock's name at all, causing CPU clocks to never link up with
their parents.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
for_each_child_of_node performs an of_node_put on each iteration, so
putting an of_node_put before a continue results in a double put.
The semantic match that finds this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
iterator name for_each_child_of_node;
@@
for_each_child_of_node(root, child) {
... when != of_node_get(child)
* of_node_put(child);
...
* continue;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* clk-bcm2835:
clk: bcm2835: Add support for programming the audio domain clocks
clk: bcm2835: Add binding docs for the new platform clock driver.
clk: bcm2835: Move under bcm/ with other Broadcom SoC clk drivers.
