0 is a valid GPIO number, use a negative number to specify, that this camera
doesn't have a GPIO for bus-width switching.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The G3IPL expects the value at RAM address 0xa020b020 to be
exactly 1 to setup the bluetooth GPIOs properly. The actual
code got a value from gpio_get_value() which was not 1, but
a "not equal to 0" integer.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
In the resume bootstrap, the early disable address is wrong.
Fix it to RAM address 0xa020b000 instead of 0xa0200000, and
make it consistent with RESUME_ENABLE_ADDR in mioa701.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch makes do_hw_reset the default reboot behavior when nothing
else matches. This restores reboot functionality on gumstix basix
devices where reboot=cold is the default boot argument.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original incorrect configuration caused GPIO79_nCS_3 being overriden,
thus resulted in the NAND flash not being detected. The real PSKTSEL pin
is on GPIO104 instead of GPIO79.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
FLASH_* and EPROM_* constants are unused, and clash with drivers:
drivers/atm/ambassador.h:257:1: warning: "FLASH_BASE" redefined
drivers/atm/ambassador.h:258:1: warning: "FLASH_SIZE" redefined
drivers/atm/iphase.h:332:1: warning: "EPROM_SIZE" redefined
so remove them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mm/dma-mapping.c: In function `dma_sync_sg_for_cpu':
arch/arm/mm/dma-mapping.c:588: warning: statement with no effect
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the critical read back to flush the next descriptor address is
fixed we can downgrade some BUG_ONs that need only be enabled when testing
changes to the driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Mikael Pettersson reported:
The 2.6.28-rc kernels fail to detect PCI device 0000:00:01.0
(the first ethernet port) on my Thecus n2100 XScale box.
There is however still a strange "ghost" device that gets partially
detected in 2.6.28-rc2 vanilla.
The IOP321 manual says:
The user designates the memory region containing the OCCDR as
non-cacheable and non-bufferable from the IntelR XScaleTM core.
This guarantees that all load/stores to the OCCDR are only of
DWORD quantities.
Ensure that the OCCDR is so mapped.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Same fix as commit c7cf72dcad: when 'start' and 'end' are less than a
cacheline apart and 'start' is unaligned we are done after cleaning and
invalidating the first cacheline.
Cc: <stable@kernel.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When 'start' and 'end' are less than a cacheline apart and 'start' is
unaligned we are done after cleaning and invalidating the first
cacheline. So check for (start < end) which will not walk off into
invalid address ranges when (start > end).
This issue was caught by drivers/dma/dmatest.
2.6.27 is susceptible.
Cc: <stable@kernel.org>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As a result of the ptebits changes, we ended up marking device mappings
as normal memory on ARMv7 CPUs, resulting in undesirable behaviour with
serial ports and the like. While reviewing the section mapping table
entries, other errors in the memory type settings for devices were
detected and confirmed to prevent Xscale3 platforms booting.
Tested on:
OMAP34xx (ARMv7),
OMAP24xx (ARMv6),
OMAP16xx (ARM926T, ARMv5),
PXA311 (Xscale3),
PXA272 (Xscale),
PXA255 (Xscale),
IXP42x (Xscale),
S3C2410 (ARM920T, ARMv4T),
ARM720T (ARMv4T)
StrongARM-110 (ARMv4)
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Ben Dooks <ben-linux@fluff.org>
Tested-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As of 73bdf0a60e, the kernel needs
to know where modules are located in the virtual address space.
On ARM, we located this region between MODULE_START and MODULE_END.
Unfortunately, everyone else calls it MODULES_VADDR and MODULES_END.
Update ARM to use the same naming, so is_vmalloc_or_module_addr()
can work properly. Also update the comment on mm/vmalloc.c to
reflect that ARM also places modules in a separate region from the
vmalloc space.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On omap24xx, INTCPS_SIR_IRQ_OFFSET bits [6:0] contains the current
active interrupt number.
However, on 34xx INTCPS_SIR_IRQ_OFFSET bits [31:7] also contains the
SPURIOUSIRQFLAG, which gets set if the interrupt sorting information
is invalid.
If the SPURIOUSIRQFLAG bits are not ignored, the interrupt code will
occasionally produce a bunch of confusing errors:
irq -33, desc: c02ddcc8, depth: 0, count: 0, unhandled: 0
->handle_irq(): c006f23c, handle_bad_irq+0x0/0x22c
->chip(): 00000000, 0x0
->action(): 00000000
Fix this by masking out only the ACTIVEIRQ bits. Also fix a
confusing comment.
Signed-off-by: Tony Lindgren <tony@atomide.com>
debugfs_create_*() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Comparing to PATCH v1, because clk_debugfs_init is included in
"#if defined CONFIG_DEBUG_FS", we only need to check NULL return.
Thanks Li Zefan <lizf@cn.fujitsu.com>
debugfs_create_u8() and other function's return value's checking method are
also fixed in this patch.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix these compiler warnings:
gpmc.c: In function 'gpmc_init':
gpmc.c:432: warning: 'return' with a value, in function returning void
gpmc.c:439: warning: 'return' with a value, in function returning void
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2.6.28-rc tightened up the ELF architecture checks on ARM. For
non-EABI it only allows VFP if the hardware supports it. However,
the kernel fails to also inspect the soft-float flag, so it
incorrectly rejects binaries using soft-VFP.
The fix is simple: also check that EF_ARM_SOFT_FLOAT isn't set
before rejecting VFP binaries on non-VFP hardware.
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
i2c_board_info array was filled incorrectly.
Due to circumstances, the way it is filled works.
This patch fills array properly.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mx31ads_defconfig compilation failed with
arch/arm/mach-mx3/mx31ads.c: In function 'mxc_init_imx_uart':
arch/arm/mach-mx3/mx31ads.c:102: error: 'mxc_uart_device0' undeclared (first use in this function)
arch/arm/mach-mx3/mx31ads.c:102: error: (Each undeclared identifier is reported only once
arch/arm/mach-mx3/mx31ads.c:102: error: for each function it appears in.)
make[1]: *** [arch/arm/mach-mx3/mx31ads.o] Error 1
Add missing include
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Data register holds the value we have written to a gpio. To
get the input value we must read the Pad Status Register MX3 (or Sample
Status register in MX1/2 terms)
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The internal devices of the MX3 Processor have to be mapped
MT_DEVICE_NONSHARED devices, otherwise cache corruptions occur.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This patch changes the gpio_free implementations for the arm architecture.
DaVinci is skipped on purpose to simplify the merge process for patches
switching it over to use gpiolib as per request by David Brownell.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix compilation of sharpsl_pm when CONFIG_PM in unselected.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The internal devices of the MX3 Processor have to be mapped
MT_DEVICE_NONSHARED devices, otherwise cache corruptions occur.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
corgi_lcd has symbol conflict with corgi_bl driver.
Fix it by renaming common symbol in new corgi_lcd driver.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Commit 40df2d1d "[ARM] Update Xscale and Xscale3 PTE mappings" was
fingered by git-bisect for a boot failure on iop13xx. The change made
L_PTE_MT_WRITETHROUGH mappings L2-uncacheable. Russell points out that
this mapping is used for the vector page. Given the regression, and the
fact this page is used often, restore the old behaviour.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: corgi backlight driver should not select ssp drivers
[ARM] 5321/1: Kirkwood: fix typo in Makefile
[ARM] 5320/1: fix assembly constraints in implementation of do_div()
[ARM] 5318/1: Swap the PRRR and NMRR values in proc-v7.S
[ARM] 5316/1: AT91: oops (regression) fix on gpio irq
[ARM] msm: vreg interface to msm7k pmic
[ARM] msm: dma: various basic dma improvements and bugfixes
[ARM] msm: clock: provide clk_*() api support for
[ARM] msm: clean up iomap and devices
[ARM] msm: add proc_comm support, necessary for clock and power control
[ARM] msm: rename ARCH_MSM7X00A to ARCH_MSM
[ARM] pxa/spitz: fix unbalance parenthesis in header file spitz.h
[ARM] pxa: update {corgi,spitz}_defconfig to favor SPI-based drivers
[ARM] pxa: fix the corgi_ssp.c dependency issue in {corgi,spitz}_defconfig
Revert "[ARM] pxa/corgi: remove now unused corgi_ssp.c and corgi_lcd.c"
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Add driver for Tabletkiosk Sahara TouchIT-213 Tablet PC
backlight: da903x: Add backlight driver for DA9030/DA9034
tosa: add support for bl/lcd driver
backlight: add support for Sharp SL-6000 LCD and backlight drivers
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb: (47 commits)
uwb: wrong sizeof argument in mac address compare
uwb: don't use printk_ratelimit() so often
uwb: use kcalloc where appropriate
uwb: use time_after() when purging stale beacons
uwb: add credits for the original developers of the UWB/WUSB/WLP subsystems
uwb: add entries in the MAINTAINERS file
uwb: depend on EXPERIMENTAL
wusb: wusb-cbaf (CBA driver) sysfs ABI simplification
uwb: document UWB and WUSB sysfs files
uwb: add symlinks in sysfs between radio controllers and PALs
uwb: dont tranmit identification IEs
uwb: i1480/GUWA100U: fix firmware download issues
uwb: i1480: remove MAC/PHY information checking function
uwb: add Intel i1480 HWA to the UWB RC quirk table
uwb: disable command/event filtering for D-Link DUB-1210
uwb: initialize the debug sub-system
uwb: Fix handling IEs with empty IE data in uwb_est_get_size()
wusb: fix bmRequestType for Abort RPipe request
wusb: fix error path for wusb_set_dev_addr()
wusb: add HWA host controller driver
...
The arch dependent function ftrace_mcount_set was only used by the daemon
start up code. This patch removes it.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
