The driver state struct for the sierra PHY driver has a field named
`regmap` that is never referenced. Remove it since it is unused.
Not that there are separate fields of type `struct regmap` for the
individual sections of the device's register map. These other regmaps are
used and not affected by the patch.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20220707071722.44201-2-lars@metafoo.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver state struct for the sierra PHY driver has a field named
`regmap` that is never referenced. Remove it since it is unused.
Not that there are separate fields of type `struct regmap` for the
individual sections of the device's register map. These other regmaps are
used and not affected by the patch.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20220707071722.44201-1-lars@metafoo.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support new compatible for dphy-tx on j721e
and implement dphy ops required.
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220623125433.18467-4-r-ravikumar@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds workaround for TI J721E errata i2183
(https://www.ti.com/lit/er/sprz455a/sprz455a.pdf).
PCIe fails to link up if SERDES lanes not used by PCIe are assigned to
another protocol. For example, link training fails if lanes 2 and 3 are
assigned to another protocol while lanes 0 and 1 are used for PCIe to
form a two lane link. This failure is due to an incorrect tie-off on an
internal status signal indicating electrical idle.
Status signals going from SERDES to PCIe Controller are tied-off when a
lane is not assigned to PCIe. Signal indicating electrical idle is
incorrectly tied-off to a state that indicates non-idle. As a result,
PCIe sees unused lanes to be out of electrical idle and this causes
LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to
occur. If a receiver is not detected on the first receiver detection
attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and
again moves forward to Detect.Active state without waiting for 12ms as
required by PCIe base specification. Since wait time in Detect.Quiet is
skipped, multiple receiver detect operations are performed back-to-back
without allowing time for capacitance on the transmit lines to
discharge. This causes subsequent receiver detection to always fail even
if a receiver gets connected eventually.
The workaround only works for 1-lane PCIe configuration. This workaround
involves enabling receiver detect override by setting TX_RCVDET_OVRD_PREG_j
register of the lane running PCIe to 0x2. This causes SERDES to indicate
successful receiver detect when LTSSM is in Detect.Active state, whether a
receiver is actually present or not. If the receiver is present, LTSSM
proceeds to link up as expected. However if receiver is not present, LTSSM
will time out in Polling.Configuration substate since the expected training
sequence packets will not be received.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20220303055026.24899-1-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Cadence D-PHY can be configured in Tx (DSI) mode or Rx (CSI) mode.
Both modes have a different programming sequence and share little among
them. In addition, a PHY configured in Tx mode cannot be used in Rx mode
and vice versa. For this reason, create a separate driver for the Rx
mode to make it easier to read and maintain.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20220301111621.2992275-2-p.yadav@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In some cases, a single SerDes instance can be shared between two different
processors, each using a separate link. In these cases, the SerDes
configuration is done in an earlier boot stage. Therefore, add support to
skip reconfiguring, if it is was already configured beforehand.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220128072642.29188-1-a-govindraju@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are two bugs in the error handling:
1: If devm_of_phy_provider_register() fails then there was no cleanup.
2: The error handling called of_node_put(child) improperly leading to
a use after free. We are only holding the reference inside the loop
so the last two gotos after the loop lead to a use after free bug.
Fix this by cleaning up the partial allocations (or partial iterations)
in the loop before doing the goto.
Fixes: a43f72ae13 ("phy: cadence: Sierra: Change MAX_LANES of Sierra to 16")
Fixes: 44d30d6228 ("phy: cadence: Add driver for Sierra PHY")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220115115146.GC7552@kili
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Sierra has derived differential reference clock output which is sourced
after the spread spectrum generation has been added. Add support to drive
derived reference clock out of serdes. Model this derived clock as a
"clock" so that platforms using this can enable it.
Sierra Main LC VCO PLL divider 1 clock is programmed to output 100MHz
clock output.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-16-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add register sequences for PCIe + QSGMII PHY multilink configuration.
PHY configuration for multi-link operation is done in two steps.
e.g. Consider a case for a 4 lane PHY with PCIe using 2 lanes and QSGMII
other 2 lanes. Sierra PHY has 2 PLLs, viz. PLLLC and PLLLC1. So in this
case, PLLLC is used for PCIe and PLLLC1 is used for QSGMII.
PHY is configured in two steps as described below.
[1] For first step, the register values are selected as
[TYPE_PCIE][TYPE_QSGMII][ssc].
This will configure PHY registers associated for PCIe involving PLLLC
registers and registers for first 2 lanes of PHY.
[2] In second step, the register values are selected as
[TYPE_QSGMII][TYPE_PCIE][ssc].
This will configure PHY registers associated for QSGMII involving
PLLLC1 registers and registers for other 2 lanes of PHY.
This completes the PHY configuration for multilink operation.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-14-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for multilink configuration of Sierra PHY. Currently,
maximum two links are supported.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-13-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix get_parent() callback to return the correct index of the parent for
PLL_CMNLC1 clock. Add a separate table of register values corresponding
to the parent index for PLL_CMNLC1. Update set_parent() callback
accordingly.
Fixes: 28081b7285 ("phy: cadence: Sierra: Model PLL_CMNLC and PLL_CMNLC1 as clocks (mux clocks)")
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-12-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add single link PCIe register configurations for no SSC and internal
SSC. Also, add missing PMA lane registers for external SSC.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-11-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PIPE phy status is used to communicate the completion of several PHY
functions. Check if PHY is ready for operation while configured for
PIPE mode during startup.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-10-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Check if PMA cmn_ready is set indicating the startup process is complete.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-9-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Sierra driver currently supports single link configurations only. Prepare
driver to support multilink multiprotocol configurations along with
different SSC modes.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-3-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use of_device_get_match_data() to get driver data instead of boilerplate
code.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-2-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use the macro 'swap()' defined in 'include/linux/minmax.h' to avoid
opencoding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Link: https://lore.kernel.org/r/20211104065233.1833499-1-yang.guang5@zte.com.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support to output received reference clock. Model the received
reference clock as an alternate parent of reference clock driver
clock. When received refclk is selected to output on cmn_refclk_p/m,
this is the internal reference clock driven on the pma_cmn_refclk_int.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210922123735.21927-5-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When reference clock driver is enabled, either derived or received refclk
is output on cmn_refclk_p/m. Update the reference clock driver
implementation by modelling reference clock driver as a "clock" with
derived reference clock set as its default parent. The support for
received reference clock will be added in a separate patch.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210922123735.21927-4-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PIPE PHY status is used to communicate the completion of several PHY
functions. Check if PHY is ready for operation while configured for
PIPE mode during startup.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210728145454.15945-10-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add debug information in probe regarding PHY configuration parameters
like single link or multilink protocol along with number of lanes
used for each protocol link.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210728145454.15945-9-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Torrent PHY driver currently supports single link DP configuration.
Prepare driver to support multilink DP configurations by adding
separate functions for common initialization sequence.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210728145454.15945-8-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add PHY registers for single link DP in array format to simplify
code and to improve readability. This supports already supported
frequencies for DP of 19.2MHz and 25MHz.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210728145454.15945-6-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Torrent PHY supports multiple serdes standards with different input
reference clock frequencies. PHY register values differ based on the
reference clock rate. Add PHY input reference clock frequency as a
new dimension to select proper register configuration. No functional
change is intended.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210728145454.15945-5-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Torrent PHY supports different input reference clock frequencies.
Register configurations will be different based on reference clock value.
Prepare driver to support such multiple reference clock frequencies.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210728145454.15945-4-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: a43f72ae13 ("phy: cadence: Sierra: Change MAX_LANES of Sierra to 16")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Link: https://lore.kernel.org/r/20210517015749.127799-1-wangwensheng4@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Torrent spec specifies delay of 660.5us after phy_reset is
asserted by the controller. To be on the safe side provide a delay
of 5ms to 10ms in ->phy_on() callback where the SERDES is already
configured in bootloader.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210330110138.24356-6-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No functional change. Since the reset controls obtained in
Torrent is exclusively used by the Torrent device, use
exclusive reset control request API calls.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210330110138.24356-5-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Do not configure torrent SERDES if it's already configured.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210330110138.24356-4-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No functional change intended. Group reset APIs and clock APIs in
preparation for adding support to skip configuration if the SERDES
is already configured by bootloader.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210330110138.24356-3-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Get pll_cmnlc and pll_cmnlc1 optional clocks and enable them.
This will enable REFRCV/1 in case the pll_cmnlc/1 takes input
from REFRCV/1 respectively.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210319124128.13308-14-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Sierra has two PLLs, PLL_CMNLC and PLL_CMNLC1 and each of these PLLs has
two inputs, plllc_refclk (input from pll0_refclk) and refrcv (input from
pll1_refclk). Model PLL_CMNLC and PLL_CMNLC1 as clocks so that it's
possible to select one of these two inputs from device tree.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210319124128.13308-13-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
commit 44d30d6228 ("phy: cadence: Add driver for Sierra PHY") enabled
the clock in probe and failed to disable in remove callback. Add missing
clk_disable_unprepare() in cdns_sierra_phy_remove().
Fixes: 44d30d6228 ("phy: cadence: Add driver for Sierra PHY")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210319124128.13308-11-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of having separate structure members for each input clock, add
an array for the input clocks within "struct cdns_sierra_phy". This is
in preparation for adding more input clocks required for supporting
additional clock combination.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210319124128.13308-10-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No functional change. In order to have a single header file for all
Cadence SERDES move phy-cadence-torrent.h to phy-cadence.h. This is
in preparation for adding Cadence Sierra SERDES specific macros.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210319124128.13308-9-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No functional change. Since the reset controls obtained in
Sierra is exclusively used by the Sierra device, use
exclusive reset control request API calls.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20210319124128.13308-8-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No functional change. Group devm_reset_control_get() and
devm_reset_control_get_optional() to a separate function.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20210319124128.13308-7-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No functional change. Group all devm_clk_get_optional() to a
separate function.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210319124128.13308-6-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cadence Sierra PHY driver registers PHY using devm_phy_create()
for all sub-nodes of Sierra device tree node. However Sierra device
tree node can have sub-nodes for the various clocks in addtion to the
PHY. Use devm_phy_create() only for nodes with name "phy" (or "link"
for old device tree) which represent the actual PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210319124128.13308-4-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 44d30d6228 ("phy: cadence: Add driver for Sierra PHY")
de-asserts PHY_RESET even before the configurations are loaded in
phy_init(). However PHY_RESET should be de-asserted only after
all the configurations has been initialized, instead of de-asserting
in probe. Fix it here.
Fixes: 44d30d6228 ("phy: cadence: Add driver for Sierra PHY")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20210319124128.13308-2-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update PCIe + USB register sequences for correct PLL1 clock configuration.
Also, update sequences for other USB configurations with dependent changes.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/1614838096-32291-5-git-send-email-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
