XFS uses CRC verification over a sub-range of the head of the log to
detect and handle torn writes. This torn log write detection currently
runs unconditionally at mount time, regardless of whether the log is
dirty or clean. This is problematic in cases where a filesystem might
end up being moved across different, incompatible (i.e., opposite
byte-endianness) architectures.
The problem lies in the fact that log data is not necessarily written in
an architecture independent format. For example, certain bits of data
are written in native endian format. Further, the size of certain log
data structures differs (i.e., struct xlog_rec_header) depending on the
word size of the cpu. This leads to false positive crc verification
errors and ultimately failed mounts when a cleanly unmounted filesystem
is mounted on a system with an incompatible architecture from data that
was written near the head of the log.
Update the log head/tail discovery code to run torn write detection only
when the log is not clean. This means something other than an unmount
record resides at the head of the log and log recovery is imminent. It
is a requirement to run log recovery on the same type of host that had
written the content of the dirty log and therefore CRC failures are
legitimate corruptions in that scenario.
Reported-by: Jan Beulich <JBeulich@suse.com>
Tested-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Once the record at the head of the log is identified and verified, the
in-core log state is updated based on the record. This includes
information such as the current head block and cycle, the start block of
the last record written to the log, the tail lsn, etc.
Once torn write detection is conditional, this logic will need to be
reused. Factor the code to update the in-core log data structures into a
new helper function. This patch does not change behavior.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Once the mount sequence has identified the head and tail blocks of the
physical log, the record at the head of the log is located and examined
for an unmount record to determine if the log is clean. This currently
occurs after torn write verification of the head region of the log.
This must ultimately be separated from torn write verification and may
need to be called again if the log head is walked back due to a torn
write (to determine whether the new head record is an unmount record).
Separate this logic into a new helper function. This patch does not
change behavior.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The code that locates the log record at the head of the log is buried in
the log head verification function. This is fine when torn write
verification occurs unconditionally, but this behavior is problematic
for filesystems that might be moved across systems with different
architectures.
In preparation for separating examination of the log head for unmount
records from torn write detection, lift the record location logic out of
the log verification function and into the caller. This patch does not
change behavior.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
When AIO DIO fails e.g. due to IO error, we must not convert unwritten
extents as that will expose uninitialized data. Handle this case
by clearing unwritten flag from io_end in case of error and thus
preventing extent conversion.
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Move the di_mode value from the xfs_icdinode to the VFS inode, reducing
the xfs_icdinode byte another 2 bytes and collapsing another 2 byte hole
in the structure.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
We can store the di_changecount in the i_version field of the VFS
inode and remove another 8 bytes from the xfs_icdinode.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Pull another 4 bytes out of the xfs_icdinode.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The VFS tracks the inode nlink just like the xfs_icdinode. We can
remove the variable from the icdinode and use the VFS inode variable
everywhere, reducing the size of the xfs_icdinode by a further 4
bytes.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
We are going to keep certain on-disk information in the VFS inode
rather than in a separate XFS specific stucture, so we have to be
careful of the VFS code clearing that information when we
re-initialise reclaimable cached inodes during lookup. If we don't
do this, then we lose critical information from the inode and that
results in corruption being detected.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
So we don't have to carry an di_onlink variable around anymore, move
the inode conversion from v1 inode format to v2 inode format into
xfs_inode_from_disk(). This means we can remove the di_onlink fields
from the struct xfs_icdinode.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Now that the struct xfs_icdinode is not directly related to the
on-disk format, we can cull things in it we really don't need to
store:
- magic number never changes
- padding is not necessary
- next_unlinked is never used
- inode number is redundant
- uuid is redundant
- lsn is accessed directly from dinode
- inode CRC is only accessed directly from dinode
Hence we can remove these from the struct xfs_icdinode and redirect
the code that uses them to the xfs_dinode appripriately. This
reduces the size of the struct icdinode from 152 bytes to 88 bytes,
and removes a fair chunk of unnecessary code, too.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The struct xfs_inode has two copies of the current timestamps in it,
one in the vfs inode and one in the struct xfs_icdinode. Now that we
no longer log the struct xfs_icdinode directly, we don't need to
keep the timestamps in this structure. instead we can copy them
straight out of the VFS inode when formatting the inode log item or
the on-disk inode.
This reduces the struct xfs_inode in size by 24 bytes.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
We currently carry around and log an entire inode core in the
struct xfs_inode. A lot of the information in the inode core is
duplicated in the VFS inode, but we cannot remove this duplication
of infomration because the inode core is logged directly in
xfs_inode_item_format().
Add a new function xfs_inode_item_format_core() that copies the
inode core data into a struct xfs_icdinode that is pulled directly
from the log vector buffer. This means we no longer directly
copy the inode core, but copy the structures one member at a time.
This will be slightly less efficient than copying, but will allow us
to remove duplicate and unnecessary items from the struct xfs_inode.
To enable us to do this, call the new structure a xfs_log_dinode,
so that we know it's different to the physical xfs_dinode and the
in-core xfs_icdinode.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Buffers without verifiers issue runtime warnings on XFS. We don't
have anything we can actually verify in the RT buffers (no CRCs, not
magic numbers, etc), but we still need verifiers to avoid the
warnings.
Add a set of dummy verifier operations for the realtime buffers and
apply them in the appropriate places.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
When logging buffers, we attach a type to them that follows the
buffer all the way into the log and is used to identify the buffer
contents in log recovery. Both the realtime summary buffers and the
bitmap buffers do not have types defined or set, so when we try to
log them we see assert failure:
XFS: Assertion failed: (bip->bli_flags & XFS_BLI_STALE) || (xfs_blft_from_flags(&bip->__bli_format) > XFS_BLFT_UNKNOWN_BUF && xfs_blft_from_flags(&bip->__bli_format) < XFS_BLFT_MAX_BUF), file: fs/xfs/xfs_buf_item.c, line: 294
Fix this by adding buffer log format types for these buffers, and
add identification support into log recovery for them. Only build the log
recovery support if CONFIG_XFS_RT=y - we can't get into log recovery for real
time filesystems if support is not built into the kernel, and this avoids
potential build problems.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
If the filesystem has shut down, xfs_end_io() currently sets an
error on the ioend and proceeds to ioend destruction. The ioend
might contain a truncate transaction if the I/O extended the size of
the file. This transaction is only cleaned up in
xfs_setfilesize_ioend(), however, which is skipped in this case.
This results in an xfs_log_ticket leak message when the associate
cache slab is destroyed (e.g., on rmmod).
This was originally reproduced by xfs/141 on a distro kernel. The
problem is reproducible on an upstream kernel, but not easily
detected in current upstream if the xfs_log_ticket cache happens to
be merged with another cache. This can be reproduced more
deterministically with the 'slab_nomerge' kernel boot option.
Update xfs_end_io() to proceed with normal end I/O processing after
an error is set on an ioend due to fs shutdown. The I/O type-based
processing is already designed to handle an I/O error and ensure
that the ioend is cleaned up correctly.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The xfs_vm_write_failed() handler is currently responsible for cleaning
up any delalloc blocks over the range of a failed write beyond EOF.
Failure to do so results in warning messages and other inconsistencies
between buffer and extent state. The ->releasepage() handler currently
warns in the event of a page being released with either unwritten or
delalloc buffers, as neither is ever expected by the time a page is
released.
As has been reproduced by generic/083 on a -bsize=1k fs, it is currently
possible to trigger the ->releasepage() warning for a page with
unwritten buffers when a filesystem is near ENOSPC. This is reproduced
by the following sequence:
$ mkfs.xfs -f -b size=1k -d size=100m <dev>
$ mount <dev> /mnt/
$
$ xfs_io -fc "falloc -k 0 1k" /mnt/file
$ dd if=/dev/zero of=/mnt/enospc conv=notrunc oflag=append
$
$ xfs_io -c "pwrite 512 1k" /mnt/file
$ xfs_io -d -c "pwrite 16k 1k" /mnt/file
The first pwrite command attempts a block unaligned write across an
unwritten block and a hole. The delalloc for the hole fails with ENOSPC
and the subsequent error handling does not clean up the unwritten buffer
that was instantiated during the first ->get_block() call.
The second pwrite triggers a warning as part of the inode mapping
invalidation that occurs prior to direct I/O. The releasepage() handler
detects the unwritten buffer at this time, warns and prevents the
release of the page.
To deal with this problem, update xfs_vm_write_failed() to clean up
unwritten as well as delalloc buffers that are beyond EOF and within the
range of the failed write.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Move the shortform attr structure definition to the same place as the
other attribute structure definitions for consistency and also so that
xfs/122 verifies the structure size.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Hendik has reported suspend failures due to xfsaild blocking the freezer
to settle down.
Jan 17 19:59:56 linux-6380 kernel: PM: Syncing filesystems ... done.
Jan 17 19:59:56 linux-6380 kernel: PM: Preparing system for sleep (mem)
Jan 17 19:59:56 linux-6380 kernel: Freezing user space processes ... (elapsed 0.001 seconds) done.
Jan 17 19:59:56 linux-6380 kernel: Freezing remaining freezable tasks ...
Jan 17 19:59:56 linux-6380 kernel: Freezing of tasks failed after 20.002 seconds (1 tasks refusing to freeze, wq_busy=0):
Jan 17 19:59:56 linux-6380 kernel: xfsaild/dm-5 S 00000000 0 1293 2 0x00000080
Jan 17 19:59:56 linux-6380 kernel: f0ef5f00 00000046 00000200 00000000 ffff9022 c02d3800 00000000 00000032
Jan 17 19:59:56 linux-6380 kernel: ee0b2400 00000032 f71e0d00 f36fabc0 f0ef2d00 f0ef6000 f0ef2d00 f12f90c0
Jan 17 19:59:56 linux-6380 kernel: f0ef5f0c c0844e44 00000000 f0ef5f6c f811e0be 00000000 00000000 f0ef2d00
Jan 17 19:59:56 linux-6380 kernel: Call Trace:
Jan 17 19:59:56 linux-6380 kernel: [<c0844e44>] schedule+0x34/0x90
Jan 17 19:59:56 linux-6380 kernel: [<f811e0be>] xfsaild+0x5de/0x600 [xfs]
Jan 17 19:59:56 linux-6380 kernel: [<c0286cbb>] kthread+0x9b/0xb0
Jan 17 19:59:56 linux-6380 kernel: [<c0848a79>] ret_from_kernel_thread+0x21/0x38
The issue has been there for quite some time but it has been made
visible by only by 24ba16bb3d ("xfs: clear PF_NOFREEZE for xfsaild
kthread") because the suspend started seeing xfsaild.
The above commit has missed that the !xfs_ail_min branch might call
schedule with TASK_INTERRUPTIBLE without calling try_to_freeze so the pm
suspend would wake up the kernel thread over and over again without any
progress. What we want here is to use freezable_schedule instead to hide
the thread from the suspend.
While we are here also change schedule_timeout to freezable variant to
prevent from spurious wakeups by suspend.
[dchinner: re-add set_freezeable call so the freezer will account properly
for this kthread. ]
Reported-by: Hendrik Woltersdorf <hendrikw@arcor.de>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Old leftovers.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
... instead of leaving it in the methods.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
We only need to communicate two bits of information to the direct I/O
completion handler:
(1) do we need to convert any unwritten extents in the range
(2) do we need to check if we need to update the inode size based
on the range passed to the completion handler
We can use the private data passed to the get_block handler and the
completion handler as a simple bitmask to communicate this information
instead of the current complicated infrastructure reusing the ioends
from the buffer I/O path, and thus avoiding a memory allocation and
a context switch for any non-trivial direct write. As a nice side
effect we also decouple the direct I/O path implementation from that
of the buffered I/O path.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
This way we can pass back errors to the file system, and allow for
cleanup required for all direct I/O invocations.
Also allow the ->end_io handlers to return errors on their own, so that
I/O completion errors can be passed on to the callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Default quotas are globally set due historical reasons. IRIX only
supported user and project quotas, and default quota was only
applied to user quotas.
In Linux, when a default quota is set, all different quota types
inherits the same default value.
An user with a quota limit larger than the default quota value, will
still be limited to the default value because the group quotas also
inherits the default quotas. Unless the group which the user belongs
to have a custom quota limit set.
This patch aims to split the default quota value by quota type.
Allowing each quota type having different default values.
Default time limits are still set globally. XFS does not set a
per-user/group timer, but a single global timer. For changing this
behavior, some changes should be made in user-space tools another
bugs being fixed.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Add code to allow the Q_XGETNEXTQUOTA quotactl to quickly find
all active quotas by examining the quota inode, and skipping
over unallocated or uninitialized regions.
Userspace can then use this interface rather than i.e. a
getpwent() loop when asked to report all active quotas.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Factor xfs_seek_hole_data into an unlocked helper which takes
an xfs inode rather than a file for internal use.
Also allow specification of "end" - the vfs lseek interface is
defined such that any offset past eof/i_size shall return -ENXIO,
but we will use this for quota code which does not maintain i_size,
and we want to be able to SEEK_DATA past i_size as well. So the
lseek path can send in i_size, and the quota code can determine
its own ending offset.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Allow us to get the appropriate quota inode from any
mp & quota flags, not necessarily associated with a
particular dqp. Needed for when we are searching for
the next active ID with quotas and we want to examine
the quota inode.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Quota IDs are unsigned, and so we can pass in values up
to 2^32-1. But if we try to initialize a block containing
values over MAX_INT, curid will overflow and assert.
curid holds a quota ID, so give it the proper
xfs_dqid_t type (and remove the now-impossible ASSERT).
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Q_GETNEXTQUOTA is exactly like Q_GETQUOTA, except that it
will return quota information for the id equal to or greater
than the id requested. In other words, if the requested id has
no quota, the command will return quota information for the
next higher id which does have a quota set. If no higher id
has an active quota, -ESRCH is returned.
This allows filesystems to do efficient iteration in kernelspace,
much like extN filesystems do in userspace when asked to report
all active quotas.
This does require a new data structure for userspace, as the
current structure does not include an ID for the returned quota
information.
Today, Ext4 with a hidden quota inode requires getpwent-style
iterations, and for systems which have i.e. LDAP backends,
this can be very slow, or even impossible if iteration is not
allowed in the configuration.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Q_XGETNEXTQUOTA is exactly like Q_XGETQUOTA, except that it
will return quota information for the id equal to or greater
than the id requested. In other words, if the requested id has
no quota, the command will return quota information for the
next higher id which does have a quota set. If no higher id
has an active quota, -ESRCH is returned.
This allows filesystems to do efficient iteration in kernelspace,
much like extN filesystems do in userspace when asked to report
all active quotas.
The patch adds a d_id field to struct qc_dqblk so that we can
pass back the id of the quota which was found, and return it
to userspace.
Today, filesystems such as XFS require getpwent-style iterations,
and for systems which have i.e. LDAP backends, this can be very
slow, or even impossible if iteration is not allowed in the
configuration.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The cmd argument to quota_quotaon() via Q_QUOTAON quotactl
is not used, so remove it.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Since the checksum function and the field are both __le32, don't
perform endian conversion when comparing the two. This fixes mount
failures on ppc64.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
RT allocation can fail on a debug kernel with:
XFS: Assertion failed: xfs_isilocked(ip, XFS_ILOCK_SHARED|XFS_ILOCK_EXCL), file: fs/xfs/libxfs/xfs_bmap.c, line: 4039
When modifying the summary inode during allocation. This occurs
because the summary inode is never locked, and xfs_bmapi_*
operations expect it to be locked. The summary inode is effectively
protected byt he lock on the bitmap inode, so this really is only a
debug kernel issue.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Here are some small USB fixes and new device ids for 4.5-rc2. Nothing
major here, full details are in the shortlog, and all of these have been
in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlauV48ACgkQMUfUDdst+ynoAgCgn5XyA+Nhizh74VUCK953YzQf
gg8AoMyIn9vglivzcWAOCbmz2T9UO5P4
=HoFp
-----END PGP SIGNATURE-----
Merge tag 'usb-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are some small USB fixes and new device ids for 4.5-rc2. Nothing
major here, full details are in the shortlog, and all of these have
been in linux-next successfully"
* tag 'usb-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: option: fix Cinterion AHxx enumeration
USB: mxu11x0: fix memory leak on usb_serial private data
USB: serial: ftdi_sio: add support for Yaesu SCU-18 cable
USB: serial: option: Adding support for Telit LE922
USB: serial: visor: fix crash on detecting device without write_urbs
USB: visor: fix null-deref at probe
USB: cp210x: add ID for IAI USB to RS485 adaptor
usb: hub: do not clear BOS field during reset device
cdc-acm:exclude Samsung phone 04e8:685d
usb: cdc-acm: send zero packet for intel 7260 modem
usb: cdc-acm: handle unlinked urb in acm read callback
Here are some small tty/serial driver fixes for 4.5-rc2.
They resolve a number of reported problems (the ioctl one specifically
has been pointed out by numerous people) and one patch adds some new
device ids for the 8250_pci driver. All have been in linux-next
successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlauWWkACgkQMUfUDdst+ykujQCfUSpPMRs3yagM24SI8ITnbEJQ
7H0An0utvQBUhgf10WA7trJ+uyzq4SsQ
=uUEE
-----END PGP SIGNATURE-----
Merge tag 'tty-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty/serial driver fixes for 4.5-rc2.
They resolve a number of reported problems (the ioctl one specifically
has been pointed out by numerous people) and one patch adds some new
device ids for the 8250_pci driver. All have been in linux-next
successfully"
* tag 'tty-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_pci: Add Intel Broadwell ports
staging/speakup: Use tty_ldisc_ref() for paste kworker
n_tty: Fix unsafe reference to "other" ldisc
tty: Fix unsafe ldisc reference via ioctl(TIOCGETD)
tty: Retry failed reopen if tty teardown in-progress
tty: Wait interruptibly for tty lock on reopen
Here are some small staging driver fixes for 4.5-rc2. One of them
predated 4.4-final, but I missed that merge window due to the holliday.
The others fix reported issues that have come up recently. The tty
change is needed for the speakup driver fix and has the ack of the tty
driver maintainer as well, i.e. myself :)
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlauWLoACgkQMUfUDdst+ynHbQCfWlGgQhtadfhtiaIKLwqy9NPG
PksAn3/z4mXX037sfm2kZrcqtcNlv9zf
=Vdai
-----END PGP SIGNATURE-----
Merge tag 'staging-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some small staging driver fixes for 4.5-rc2.
One of them predated 4.4-final, but I missed that merge window due to
the holliday. The others fix reported issues that have come up
recently. The tty change is needed for the speakup driver fix and has
the ack of the tty driver maintainer as well, i.e. myself :)
All have been in linux-next with no reported issues"
* tag 'staging-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Staging: speakup: fix read scrolled-back VT
Staging: speakup: Fix getting port information
Revert "Staging: panel: usleep_range is preferred over udelay"
iio: adis_buffer: Fix out-of-bounds memory access
Here's a single driver core fix that resolves an issue a lot of users
have been hitting for a while now. It's been tested a lot and has been
in linux-next successfully for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlauV+8ACgkQMUfUDdst+yk/OQCgzI8I8xgSbGIZBkO+mq+j43SR
FVYAoKWvwo55sqbKrDyN/bqLZWxwQYFV
=jvr3
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here's a single driver core fix that resolves an issue a lot of users
have been hitting for a while now. It's been tested a lot and has
been in linux-next successfully for a while"
* tag 'driver-core-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
base/platform: Fix platform drivers with no probe callback
Pull MIPS fix from Ralf Baechle:
"Just a single revert for a patch which I had upstreamed out of
sequence"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
Revert "MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function"
Pull x86 fixes from Thomas Gleixner:
"A bit on the largish side due to a series of fixes for a regression in
the x86 vector management which was introduced in 4.3. This work was
started in December already, but it took some time to fix all corner
cases and a couple of older bugs in that area which were detected
while at it
Aside of that a few platform updates for intel-mid, quark and UV and
two fixes for in the mm code:
- Use proper types for pgprot values to avoid truncation
- Prevent a size truncation in the pageattr code when setting page
attributes for large mappings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86/mm/pat: Avoid truncation when converting cpa->numpages to address
x86/mm: Fix types used in pgprot cacheability flags translations
x86/platform/quark: Print boundaries correctly
x86/platform/UV: Remove EFI memmap quirk for UV2+
x86/platform/intel-mid: Join string and fix SoC name
x86/platform/intel-mid: Enable 64-bit build
x86/irq: Plug vector cleanup race
x86/irq: Call irq_force_move_complete with irq descriptor
x86/irq: Remove outgoing CPU from vector cleanup mask
x86/irq: Remove the cpumask allocation from send_cleanup_vector()
x86/irq: Clear move_in_progress before sending cleanup IPI
x86/irq: Remove offline cpus from vector cleanup
x86/irq: Get rid of code duplication
x86/irq: Copy vectormask instead of an AND operation
x86/irq: Check vector allocation early
x86/irq: Reorganize the search in assign_irq_vector
x86/irq: Reorganize the return path in assign_irq_vector
x86/irq: Do not use apic_chip_data.old_domain as temporary buffer
x86/irq: Validate that irq descriptor is still active
x86/irq: Fix a race in x86_vector_free_irqs()
...
