TDX guest requires CR0.NE to be set. Clearing the bit triggers #GP(0).
If CR0.NE is 0, the MS-DOS compatibility mode for handling floating-point
exceptions is selected. In this mode, the software exception handler for
floating-point exceptions is invoked externally using the processor’s
FERR#, INTR, and IGNNE# pins.
Using FERR# and IGNNE# to handle floating-point exception is deprecated.
CR0.NE=0 also limits newer processors to operate with one logical
processor active.
Kernel uses CR0_STATE constant to initialize CR0. It has NE bit set.
But during early boot kernel has more ad-hoc approach to setting bit
in the register. During some of this ad-hoc manipulation, CR0.NE is
cleared. This causes a #GP in TDX guests and makes it die in early boot.
Make CR0 initialization consistent, deriving the initial value of CR0
from CR0_STATE. Since CR0_STATE always has CR0.NE=1, this ensures that
CR0.NE is never 0 and avoids the #GP.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-23-kirill.shutemov@linux.intel.com
Secondary CPU startup is currently performed with something called
the "INIT/SIPI protocol". This protocol requires assistance from
VMMs to boot guests. As should be a familiar story by now, that
support can not be provded to TDX guests because TDX VMMs are
not trusted by guests.
To remedy this situation a new[1] "Multiprocessor Wakeup Structure"
has been added to to an existing ACPI table (MADT). This structure
provides the physical address of a "mailbox". A write to the mailbox
then steers the secondary CPU to the boot code.
Add ACPI MADT wake structure parsing support and wake support. Use
this support to wake CPUs whenever it is present instead of INIT/SIPI.
While this structure can theoretically be used on 32-bit kernels,
there are no 32-bit TDX guest kernels. It has not been tested and
can not practically *be* tested on 32-bit. Make it 64-bit only.
1. Details about the new structure can be found in ACPI v6.4, in the
"Multiprocessor Wakeup Structure" section.
Co-developed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220405232939.73860-22-kirill.shutemov@linux.intel.com
Historically, x86 platforms have booted secondary processors (APs)
using INIT followed by the start up IPI (SIPI) messages. In regular
VMs, this boot sequence is supported by the VMM emulation. But such a
wakeup model is fatal for secure VMs like TDX in which VMM is an
untrusted entity. To address this issue, a new wakeup model was added
in ACPI v6.4, in which firmware (like TDX virtual BIOS) will help boot
the APs. More details about this wakeup model can be found in ACPI
specification v6.4, the section titled "Multiprocessor Wakeup Structure".
Since the existing trampoline code requires processors to boot in real
mode with 16-bit addressing, it will not work for this wakeup model
(because it boots the AP in 64-bit mode). To handle it, extend the
trampoline code to support 64-bit mode firmware handoff. Also, extend
IDT and GDT pointers to support 64-bit mode hand off.
There is no TDX-specific detection for this new boot method. The kernel
will rely on it as the sole boot method whenever the new ACPI structure
is present.
The ACPI table parser for the MADT multiprocessor wake up structure and
the wakeup method that uses this structure will be added by the following
patch in this series.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-21-kirill.shutemov@linux.intel.com
KVM hypercalls use the VMCALL or VMMCALL instructions. Although the ABI
is similar, those instructions no longer function for TDX guests.
Make vendor-specific TDVMCALLs instead of VMCALL. This enables TDX
guests to run with KVM acting as the hypervisor.
Among other things, KVM hypercall is used to send IPIs.
Since the KVM driver can be built as a kernel module, export
tdx_kvm_hypercall() to make the symbols visible to kvm.ko.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-20-kirill.shutemov@linux.intel.com
TDX guests cannot do port I/O directly. The TDX module triggers a #VE
exception to let the guest kernel emulate port I/O by converting them
into TDCALLs to call the host.
But before IDT handlers are set up, port I/O cannot be emulated using
normal kernel #VE handlers. To support the #VE-based emulation during
this boot window, add a minimal early #VE handler support in early
exception handlers. This is similar to what AMD SEV does. This is
mainly to support earlyprintk's serial driver, as well as potentially
the VGA driver.
The early handler only supports I/O-related #VE exceptions. Unhandled or
failed exceptions will be handled via early_fixup_exceptions() (like
normal exception failures). At runtime I/O-related #VE exceptions (along
with other types) handled by virt_exception_kernel().
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220405232939.73860-19-kirill.shutemov@linux.intel.com
TDX hypervisors cannot emulate instructions directly. This includes
port I/O which is normally emulated in the hypervisor. All port I/O
instructions inside TDX trigger the #VE exception in the guest and
would be normally emulated there.
Use a hypercall to emulate port I/O. Extend the
tdx_handle_virt_exception() and add support to handle the #VE due to
port I/O instructions.
String I/O operations are not supported in TDX. Unroll them by declaring
CC_ATTR_GUEST_UNROLL_STRING_IO confidential computing attribute.
== Userspace Implications ==
The ioperm() facility allows userspace access to I/O instructions like
inb/outb. Among other things, this allows writing userspace device
drivers.
This series has no special handling for ioperm(). Users will be able to
successfully request I/O permissions but will induce a #VE on their
first I/O instruction which leads SIGSEGV. If this is undesirable users
can enable kernel lockdown feature with 'lockdown=integrity' kernel
command line option. It makes ioperm() fail.
More robust handling of this situation (denying ioperm() in all TDX
guests) will be addressed in follow-on work.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-18-kirill.shutemov@linux.intel.com
Port I/O instructions trigger #VE in the TDX environment. In response to
the exception, kernel emulates these instructions using hypercalls.
But during early boot, on the decompression stage, it is cumbersome to
deal with #VE. It is cleaner to go to hypercalls directly, bypassing #VE
handling.
Hook up TDX-specific port I/O helpers if booting in TDX environment.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220405232939.73860-17-kirill.shutemov@linux.intel.com
Port I/O instructions trigger #VE in the TDX environment. In response to
the exception, kernel emulates these instructions using hypercalls.
But during early boot, on the decompression stage, it is cumbersome to
deal with #VE. It is cleaner to go to hypercalls directly, bypassing #VE
handling.
Add a way to hook up alternative port I/O helpers in the boot stub with
a new pio_ops structure. For now, set the ops structure to just call
the normal I/O operation functions.
out*()/in*() macros redefined to use pio_ops callbacks. It eliminates
need in changing call sites. io_delay() changed to use port I/O helper
instead of inline assembly.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220405232939.73860-16-kirill.shutemov@linux.intel.com
There are two implementations of port I/O helpers: one in the kernel and
one in the boot stub.
Move the helpers required for both to <asm/shared/io.h> and use the one
implementation everywhere.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-15-kirill.shutemov@linux.intel.com
Change port I/O helpers to use u8/u16/u32 instead of unsigned
char/short/int for values. Use u16 instead of int for port number.
It aligns the helpers with implementation in boot stub in preparation
for consolidation.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-14-kirill.shutemov@linux.intel.com
The early decompression code does port I/O for its console output. But,
handling the decompression-time port I/O demands a different approach
from normal runtime because the IDT required to support #VE based port
I/O emulation is not yet set up. Paravirtualizing I/O calls during
the decompression step is acceptable because the decompression code
doesn't have a lot of call sites to IO instruction.
To support port I/O in decompression code, TDX must be detected before
the decompression code might do port I/O. Detect whether the kernel runs
in a TDX guest.
Add an early_is_tdx_guest() interface to query the cached TDX guest
status in the decompression code.
TDX is detected with CPUID. Make cpuid_count() accessible outside
boot/cpuflags.c.
TDX detection in the main kernel is very similar. Move common bits
into <asm/shared/tdx.h>.
The actual port I/O paravirtualization will come later in the series.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220405232939.73860-13-kirill.shutemov@linux.intel.com
In non-TDX VMs, MMIO is implemented by providing the guest a mapping
which will cause a VMEXIT on access and then the VMM emulating the
instruction that caused the VMEXIT. That's not possible for TDX VM.
To emulate an instruction an emulator needs two things:
- R/W access to the register file to read/modify instruction arguments
and see RIP of the faulted instruction.
- Read access to memory where instruction is placed to see what to
emulate. In this case it is guest kernel text.
Both of them are not available to VMM in TDX environment:
- Register file is never exposed to VMM. When a TD exits to the module,
it saves registers into the state-save area allocated for that TD.
The module then scrubs these registers before returning execution
control to the VMM, to help prevent leakage of TD state.
- TDX does not allow guests to execute from shared memory. All executed
instructions are in TD-private memory. Being private to the TD, VMMs
have no way to access TD-private memory and no way to read the
instruction to decode and emulate it.
In TDX the MMIO regions are instead configured by VMM to trigger a #VE
exception in the guest.
Add #VE handling that emulates the MMIO instruction inside the guest and
converts it into a controlled hypercall to the host.
This approach is bad for performance. But, it has (virtually) no impact
on the size of the kernel image and will work for a wide variety of
drivers. This allows TDX deployments to use arbitrary devices and device
drivers, including virtio. TDX customers have asked for the capability
to use random devices in their deployments.
In other words, even if all of the work was done to paravirtualize all
x86 MMIO users and virtio, this approach would still be needed. There
is essentially no way to get rid of this code.
This approach is functional for all in-kernel MMIO users current and
future and does so with a minimal amount of code and kernel image bloat.
MMIO addresses can be used with any CPU instruction that accesses
memory. Address only MMIO accesses done via io.h helpers, such as
'readl()' or 'writeq()'.
Any CPU instruction that accesses memory can also be used to access
MMIO. However, by convention, MMIO access are typically performed via
io.h helpers such as 'readl()' or 'writeq()'.
The io.h helpers intentionally use a limited set of instructions when
accessing MMIO. This known, limited set of instructions makes MMIO
instruction decoding and emulation feasible in KVM hosts and SEV guests
today.
MMIO accesses performed without the io.h helpers are at the mercy of the
compiler. Compilers can and will generate a much more broad set of
instructions which can not practically be decoded and emulated. TDX
guests will oops if they encounter one of these decoding failures.
This means that TDX guests *must* use the io.h helpers to access MMIO.
This requirement is not new. Both KVM hosts and AMD SEV guests have the
same limitations on MMIO access.
=== Potential alternative approaches ===
== Paravirtualizing all MMIO ==
An alternative to letting MMIO induce a #VE exception is to avoid
the #VE in the first place. Similar to the port I/O case, it is
theoretically possible to paravirtualize MMIO accesses.
Like the exception-based approach offered here, a fully paravirtualized
approach would be limited to MMIO users that leverage common
infrastructure like the io.h macros.
However, any paravirtual approach would be patching approximately 120k
call sites. Any paravirtual approach would need to replace a bare memory
access instruction with (at least) a function call. With a conservative
overhead estimation of 5 bytes per call site (CALL instruction),
it leads to bloating code by 600k.
Many drivers will never be used in the TDX environment and the bloat
cannot be justified.
== Patching TDX drivers ==
Rather than touching the entire kernel, it might also be possible to
just go after drivers that use MMIO in TDX guests *and* are performance
critical to justify the effrort. Right now, that's limited only to virtio.
All virtio MMIO appears to be done through a single function, which
makes virtio eminently easy to patch.
This approach will be adopted in the future, removing the bulk of
MMIO #VEs. The #VE-based MMIO will remain serving non-virtio use cases.
Co-developed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-12-kirill.shutemov@linux.intel.com
In TDX guests, most CPUID leaf/sub-leaf combinations are virtualized
by the TDX module while some trigger #VE.
Implement the #VE handling for EXIT_REASON_CPUID by handing it through
the hypercall, which in turn lets the TDX module handle it by invoking
the host VMM.
More details on CPUID Virtualization can be found in the TDX module
specification, the section titled "CPUID Virtualization".
Note that VMM that handles the hypercall is not trusted. It can return
data that may steer the guest kernel in wrong direct. Only allow VMM
to control range reserved for hypervisor communication.
Return all-zeros for any CPUID outside the hypervisor range. It matches
CPU behaviour for non-supported leaf.
Co-developed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-11-kirill.shutemov@linux.intel.com
Use hypercall to emulate MSR read/write for the TDX platform.
There are two viable approaches for doing MSRs in a TD guest:
1. Execute the RDMSR/WRMSR instructions like most VMs and bare metal
do. Some will succeed, others will cause a #VE. All of those that
cause a #VE will be handled with a TDCALL.
2. Use paravirt infrastructure. The paravirt hook has to keep a list
of which MSRs would cause a #VE and use a TDCALL. All other MSRs
execute RDMSR/WRMSR instructions directly.
The second option can be ruled out because the list of MSRs was
challenging to maintain. That leaves option #1 as the only viable
solution for the minimal TDX support.
Kernel relies on the exception fixup machinery to handle MSR access
errors. #VE handler uses the same exception fixup code as #GP. It
covers MSR accesses along with other types of fixups.
For performance-critical MSR writes (like TSC_DEADLINE), future patches
will replace the WRMSR/#VE sequence with the direct TDCALL.
RDMSR and WRMSR specification details can be found in
Guest-Host-Communication Interface (GHCI) for Intel Trust Domain
Extensions (Intel TDX) specification, sec titled "TDG.VP.
VMCALL<Instruction.RDMSR>" and "TDG.VP.VMCALL<Instruction.WRMSR>".
Co-developed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-10-kirill.shutemov@linux.intel.com
The HLT instruction is a privileged instruction, executing it stops
instruction execution and places the processor in a HALT state. It
is used in kernel for cases like reboot, idle loop and exception fixup
handlers. For the idle case, interrupts will be enabled (using STI)
before the HLT instruction (this is also called safe_halt()).
To support the HLT instruction in TDX guests, it needs to be emulated
using TDVMCALL (hypercall to VMM). More details about it can be found
in Intel Trust Domain Extensions (Intel TDX) Guest-Host-Communication
Interface (GHCI) specification, section TDVMCALL[Instruction.HLT].
In TDX guests, executing HLT instruction will generate a #VE, which is
used to emulate the HLT instruction. But #VE based emulation will not
work for the safe_halt() flavor, because it requires STI instruction to
be executed just before the TDCALL. Since idle loop is the only user of
safe_halt() variant, handle it as a special case.
To avoid *safe_halt() call in the idle function, define the
tdx_guest_idle() and use it to override the "x86_idle" function pointer
for a valid TDX guest.
Alternative choices like PV ops have been considered for adding
safe_halt() support. But it was rejected because HLT paravirt calls
only exist under PARAVIRT_XXL, and enabling it in TDX guest just for
safe_halt() use case is not worth the cost.
Co-developed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220405232939.73860-9-kirill.shutemov@linux.intel.com
Virtualization Exceptions (#VE) are delivered to TDX guests due to
specific guest actions which may happen in either user space or the
kernel:
* Specific instructions (WBINVD, for example)
* Specific MSR accesses
* Specific CPUID leaf accesses
* Access to specific guest physical addresses
Syscall entry code has a critical window where the kernel stack is not
yet set up. Any exception in this window leads to hard to debug issues
and can be exploited for privilege escalation. Exceptions in the NMI
entry code also cause issues. Returning from the exception handler with
IRET will re-enable NMIs and nested NMI will corrupt the NMI stack.
For these reasons, the kernel avoids #VEs during the syscall gap and
the NMI entry code. Entry code paths do not access TD-shared memory,
MMIO regions, use #VE triggering MSRs, instructions, or CPUID leaves
that might generate #VE. VMM can remove memory from TD at any point,
but access to unaccepted (or missing) private memory leads to VM
termination, not to #VE.
Similarly to page faults and breakpoints, #VEs are allowed in NMI
handlers once the kernel is ready to deal with nested NMIs.
During #VE delivery, all interrupts, including NMIs, are blocked until
TDGETVEINFO is called. It prevents #VE nesting until the kernel reads
the VE info.
TDGETVEINFO retrieves the #VE info from the TDX module, which also
clears the "#VE valid" flag. This must be done before anything else as
any #VE that occurs while the valid flag is set escalates to #DF by TDX
module. It will result in an oops.
Virtual NMIs are inhibited if the #VE valid flag is set. NMI will not be
delivered until TDGETVEINFO is called.
For now, convert unhandled #VE's (everything, until later in this
series) so that they appear just like a #GP by calling the
ve_raise_fault() directly. The ve_raise_fault() function is similar
to #GP handler and is responsible for sending SIGSEGV to userspace
and CPU die and notifying debuggers and other die chain users.
Co-developed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Co-developed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220405232939.73860-8-kirill.shutemov@linux.intel.com
TDX brings a new exception -- Virtualization Exception (#VE). Handling
of #VE structurally very similar to handling #GP.
Extract two helpers from exc_general_protection() that can be reused for
handling #VE.
No functional changes.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220405232939.73860-7-kirill.shutemov@linux.intel.com
In TDX guests, by default memory is protected from host access. If a
guest needs to communicate with the VMM (like the I/O use case), it uses
a single bit in the physical address to communicate the protected/shared
attribute of the given page.
In the x86 ARCH code, __PHYSICAL_MASK macro represents the width of the
physical address in the given architecture. It is used in creating
physical PAGE_MASK for address bits in the kernel. Since in TDX guest,
a single bit is used as metadata, it needs to be excluded from valid
physical address bits to avoid using incorrect addresses bits in the
kernel.
Enable DYNAMIC_PHYSICAL_MASK to support updating the __PHYSICAL_MASK.
Co-developed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-6-kirill.shutemov@linux.intel.com
Confidential Computing (CC) features (like string I/O unroll support,
memory encryption/decryption support, etc) are conditionally enabled
in the kernel using cc_platform_has() API. Since TDX guests also need
to use these CC features, extend cc_platform_has() API and add TDX
guest-specific CC attributes support.
CC API also provides an interface to deal with encryption mask. Extend
it to cover TDX.
Details about which bit in the page table entry to be used to indicate
shared/private state is determined by using the TDINFO TDCALL.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-5-kirill.shutemov@linux.intel.com
Guests communicate with VMMs with hypercalls. Historically, these
are implemented using instructions that are known to cause VMEXITs
like VMCALL, VMLAUNCH, etc. However, with TDX, VMEXITs no longer
expose the guest state to the host. This prevents the old hypercall
mechanisms from working. So, to communicate with VMM, TDX
specification defines a new instruction called TDCALL.
In a TDX based VM, since the VMM is an untrusted entity, an intermediary
layer -- TDX module -- facilitates secure communication between the host
and the guest. TDX module is loaded like a firmware into a special CPU
mode called SEAM. TDX guests communicate with the TDX module using the
TDCALL instruction.
A guest uses TDCALL to communicate with both the TDX module and VMM.
The value of the RAX register when executing the TDCALL instruction is
used to determine the TDCALL type. A leaf of TDCALL used to communicate
with the VMM is called TDVMCALL.
Add generic interfaces to communicate with the TDX module and VMM
(using the TDCALL instruction).
__tdx_module_call() - Used to communicate with the TDX module (via
TDCALL instruction).
__tdx_hypercall() - Used by the guest to request services from
the VMM (via TDVMCALL leaf of TDCALL).
Also define an additional wrapper _tdx_hypercall(), which adds error
handling support for the TDCALL failure.
The __tdx_module_call() and __tdx_hypercall() helper functions are
implemented in assembly in a .S file. The TDCALL ABI requires
shuffling arguments in and out of registers, which proved to be
awkward with inline assembly.
Just like syscalls, not all TDVMCALL use cases need to use the same
number of argument registers. The implementation here picks the current
worst-case scenario for TDCALL (4 registers). For TDCALLs with fewer
than 4 arguments, there will end up being a few superfluous (cheap)
instructions. But, this approach maximizes code reuse.
For registers used by the TDCALL instruction, please check TDX GHCI
specification, the section titled "TDCALL instruction" and "TDG.VP.VMCALL
Interface".
Based on previous patch by Sean Christopherson.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-4-kirill.shutemov@linux.intel.com
Secure Arbitration Mode (SEAM) is an extension of VMX architecture. It
defines a new VMX root operation (SEAM VMX root) and a new VMX non-root
operation (SEAM VMX non-root) which are both isolated from the legacy
VMX operation where the host kernel runs.
A CPU-attested software module (called 'TDX module') runs in SEAM VMX
root to manage and protect VMs running in SEAM VMX non-root. SEAM VMX
root is also used to host another CPU-attested software module (called
'P-SEAMLDR') to load and update the TDX module.
Host kernel transits to either P-SEAMLDR or TDX module via the new
SEAMCALL instruction, which is essentially a VMExit from VMX root mode
to SEAM VMX root mode. SEAMCALLs are leaf functions defined by
P-SEAMLDR and TDX module around the new SEAMCALL instruction.
A guest kernel can also communicate with TDX module via TDCALL
instruction.
TDCALLs and SEAMCALLs use an ABI different from the x86-64 system-v ABI.
RAX is used to carry both the SEAMCALL leaf function number (input) and
the completion status (output). Additional GPRs (RCX, RDX, R8-R11) may
be further used as both input and output operands in individual leaf.
TDCALL and SEAMCALL share the same ABI and require the largely same
code to pass down arguments and retrieve results.
Define an assembly macro that can be used to implement C wrapper for
both TDCALL and SEAMCALL.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-3-kirill.shutemov@linux.intel.com
In preparation of extending cc_platform_has() API to support TDX guest,
use CPUID instruction to detect support for TDX guests in the early
boot code (via tdx_early_init()). Since copy_bootdata() is the first
user of cc_platform_has() API, detect the TDX guest status before it.
Define a synthetic feature flag (X86_FEATURE_TDX_GUEST) and set this
bit in a valid TDX guest platform.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-2-kirill.shutemov@linux.intel.com
- Rename the staging files to give them some meaning.
Just stage1,stag2,etc, does not show what they are for
- Check for NULL from allocation in bootconfig
- Hold event mutex for dyn_event call in user events
- Mark user events to broken (to work on the API)
- Remove eBPF updates from user events
- Remove user events from uapi header to keep it from being installed.
- Move ftrace_graph_is_dead() into inline as it is called from hot paths
and also convert it into a static branch.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYkmyIBQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qutfAQD90gbUgFMFe2akF5sKhonF5T6mm0+w
BsWqNlBEKBxmfwD+Krfpxql/PKp/gCufcIUUkYC4E6Wl9akf3eO1qQel1Ao=
=ZTn1
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull more tracing updates from Steven Rostedt:
- Rename the staging files to give them some meaning. Just
stage1,stag2,etc, does not show what they are for
- Check for NULL from allocation in bootconfig
- Hold event mutex for dyn_event call in user events
- Mark user events to broken (to work on the API)
- Remove eBPF updates from user events
- Remove user events from uapi header to keep it from being installed.
- Move ftrace_graph_is_dead() into inline as it is called from hot
paths and also convert it into a static branch.
* tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Move user_events.h temporarily out of include/uapi
ftrace: Make ftrace_graph_is_dead() a static branch
tracing: Set user_events to BROKEN
tracing/user_events: Remove eBPF interfaces
tracing/user_events: Hold event_mutex during dyn_event_add
proc: bootconfig: Add null pointer check
tracing: Rename the staging files for trace_events
dropping rate range requests. It's best to keep various systems booting
so we'll kick this out and try again next time.
-----BEGIN PGP SIGNATURE-----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=OJT3
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"A single revert to fix a boot regression seen when clk_put() started
dropping rate range requests. It's best to keep various systems
booting so we'll kick this out and try again next time"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Revert "clk: Drop the rate range on clk_put()"
- Make the prctl() for enabling dynamic XSTATE components correct so it
adds the newly requested feature to the permission bitmap instead of
overwriting it. Add a selftest which validates that.
- Unroll string MMIO for encrypted SEV guests as the hypervisor cannot
emulate it.
- Handle supervisor states correctly in the FPU/XSTATE code so it takes
the feature set of the fpstate buffer into account. The feature sets
can differ between host and guest buffers. Guest buffers do not contain
supervisor states. So far this was not an issue, but with enabling
PASID it needs to be handled in the buffer offset calculation and in
the permission bitmaps.
- Avoid a gazillion of repeated CPUID invocations in by caching the values
early in the FPU/XSTATE code.
- Enable CONFIG_WERROR for X86.
- Make the X86 defconfigs more useful by adapting them to Y2022 reality.
-----BEGIN PGP SIGNATURE-----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=GK27
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of x86 fixes and updates:
- Make the prctl() for enabling dynamic XSTATE components correct so
it adds the newly requested feature to the permission bitmap
instead of overwriting it. Add a selftest which validates that.
- Unroll string MMIO for encrypted SEV guests as the hypervisor
cannot emulate it.
- Handle supervisor states correctly in the FPU/XSTATE code so it
takes the feature set of the fpstate buffer into account. The
feature sets can differ between host and guest buffers. Guest
buffers do not contain supervisor states. So far this was not an
issue, but with enabling PASID it needs to be handled in the buffer
offset calculation and in the permission bitmaps.
- Avoid a gazillion of repeated CPUID invocations in by caching the
values early in the FPU/XSTATE code.
- Enable CONFIG_WERROR in x86 defconfig.
- Make the X86 defconfigs more useful by adapting them to Y2022
reality"
* tag 'x86-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu/xstate: Consolidate size calculations
x86/fpu/xstate: Handle supervisor states in XSTATE permissions
x86/fpu/xsave: Handle compacted offsets correctly with supervisor states
x86/fpu: Cache xfeature flags from CPUID
x86/fpu/xsave: Initialize offset/size cache early
x86/fpu: Remove unused supervisor only offsets
x86/fpu: Remove redundant XCOMP_BV initialization
x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO
x86/config: Make the x86 defconfigs a bit more usable
x86/defconfig: Enable WERROR
selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test
x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation
generalized.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAmJJV1gTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYof8tD/0Xs4qpxlR81PgZSJ3QJ9vok5tKpe3j
O+ZLvQtyc2dnkduSOpJXiKe5YxDZ39Ihb7Fb9ETSUFS0ohJFDYiR6bKVXqKBjp6g
Z0u57B3j/ZrZt9W3oK2BxlKBgen3MTYmybPQja+oTZfuu+Vd+DKD6NEyGcOZe53G
+ZzEnBevar+f+/ble4PmJrnu5fP63jlUDPlY6h7HnsS2+MYTlx8JOMyhc4v4KxpR
od4/9NUMbcpV4q2hReC5D22TArhr/7woNaCFswnOuk+mb9d8sPvqv9U8iHC/YoTM
IeX3Bt1qHRT++Sjkkup2/k0xAy50H/7wMbQP+Jb993rWlLiWSd2WY0OHZ+gWSfgG
oM6a2yAZ029klyMBvV0AdiAYpvhlDs36UZBLyIIa8M4zRgH9h+//F9UZ5qnt+0kp
ACTd/B+bksbvO4A1npxZ1fUWPw6L5a8730GIy/csvAsoRlOaITfCFVA98ob+36TF
JUdyuzRAOrbt3H7pRUB+xz0pxxPkceoBBwrBTcSw1cyIyV3b8CaFT2oRWY3nt+er
THWuiXY4Jy2wtNcHMhKIZKBCtUZ7sDUBhcnplxL+qoRJ0V340B2Kh1J8/0mnjDD+
Aks4E7Q3ogpyuMXAKDEGebyTPcRe0bQXyyjJVR9cuPn5i8AM9/rv5Iqem4Ed1hLK
dQeXuWx6zLcGrw==
=mJKF
-----END PGP SIGNATURE-----
Merge tag 'core-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RT signal fix from Thomas Gleixner:
"Revert the RT related signal changes. They need to be reworked and
generalized"
* tag 'core-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "signal, x86: Delay calling signals in atomic on RT enabled kernels"
- fix a regression in dma remap handling vs AMD memory encryption (me)
- finally kill off the legacy PCI DMA API (Christophe JAILLET)
-----BEGIN PGP SIGNATURE-----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=q+vI
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.18-1' of git://git.infradead.org/users/hch/dma-mapping
Pull more dma-mapping updates from Christoph Hellwig:
- fix a regression in dma remap handling vs AMD memory encryption (me)
- finally kill off the legacy PCI DMA API (Christophe JAILLET)
* tag 'dma-mapping-5.18-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: move pgprot_decrypted out of dma_pgprot
PCI/doc: cleanup references to the legacy PCI DMA API
PCI: Remove the deprecated "pci-dma-compat.h" API
This reverts commit 7dabfa2bc4. There are
multiple reports that this breaks boot on various systems. The common
theme is that orphan clks are having rates set on them when that isn't
expected. Let's revert it out for now so that -rc1 boots.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://lore.kernel.org/r/366a0232-bb4a-c357-6aa8-636e398e05eb@samsung.com
Cc: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220403022818.39572-1-sboyd@kernel.org
- Avoid SEGV if core.cpus isn't set in 'perf stat'.
- Stop depending on .git files for building PERF-VERSION-FILE, used in
'perf --version', fixing some perf tools build scenarios.
- Convert tracepoint.py example to python3.
- Update UAPI header copies from the kernel sources:
socket, mman-common, msr-index, KVM, i915 and cpufeatures.
- Update copy of libbpf's hashmap.c.
- Directly return instead of using local ret variable in
evlist__create_syswide_maps(), found by coccinelle.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCYkhUwgAKCRCyPKLppCJ+
JyjjAQCSTOHqJfrxCvt+VeZvAlZv5FVYosGBUXQTwZuWLV4LtAEA7+Q3VApPDskc
Izd4hgtR+g5ukHH5G1pgPZpCbTGnrgg=
=/yvf
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-for-v5.18-2022-04-02' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Avoid SEGV if core.cpus isn't set in 'perf stat'.
- Stop depending on .git files for building PERF-VERSION-FILE, used in
'perf --version', fixing some perf tools build scenarios.
- Convert tracepoint.py example to python3.
- Update UAPI header copies from the kernel sources: socket,
mman-common, msr-index, KVM, i915 and cpufeatures.
- Update copy of libbpf's hashmap.c.
- Directly return instead of using local ret variable in
evlist__create_syswide_maps(), found by coccinelle.
* tag 'perf-tools-for-v5.18-2022-04-02' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf python: Convert tracepoint.py example to python3
perf evlist: Directly return instead of using local ret variable
perf cpumap: More cpu map reuse by merge.
perf cpumap: Add is_subset function
perf evlist: Rename cpus to user_requested_cpus
perf tools: Stop depending on .git files for building PERF-VERSION-FILE
tools headers cpufeatures: Sync with the kernel sources
tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
tools headers UAPI: Sync linux/kvm.h with the kernel sources
tools kvm headers arm64: Update KVM headers from the kernel sources
tools arch x86: Sync the msr-index.h copy with the kernel sources
tools headers UAPI: Sync asm-generic/mman-common.h with the kernel
perf beauty: Update copy of linux/socket.h with the kernel sources
perf tools: Update copy of libbpf's hashmap.c
perf stat: Avoid SEGV if core.cpus isn't set
* Documentation improvements
* Prevent module exit until all VMs are freed
* PMU Virtualization fixes
* Fix for kvm_irq_delivery_to_apic_fast() NULL-pointer dereferences
* Other miscellaneous bugfixes
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmJIGV8UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroO5FQgAhls4+Nu+NqId/yvvyNxr3vXq0dHI
hLlHtvzgGzZisZ7y2bNeyIpJVBDT5LCbrptPD/5eTvchVswDh0+kCVC0Uni5ugGT
tLT/Pv9Oq9e0X7aGdHRyuHIivIFDC20zIZO2DV48Lrj/+r6DafB2Fghq2XQLlBxN
p8KislvuqAAos543BPC1+Lk3dhOLuZ8qcFD8wGRlcCwjNwYaitrQ16rO04cLfUur
OwIks1I6TdI2JpLBhm6oWYVG/YnRsoo4bQE8cjdQ6yNSbwWtRpV33q7X6onw8x8K
BEeESoTnMqfaxIF/6mPl6bnDblVHFp6Xhld/vJcgeWQTdajFtuFE/K4sCA==
=xnQ6
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
- Only do MSR filtering for MSRs accessed by rdmsr/wrmsr
- Documentation improvements
- Prevent module exit until all VMs are freed
- PMU Virtualization fixes
- Fix for kvm_irq_delivery_to_apic_fast() NULL-pointer dereferences
- Other miscellaneous bugfixes
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (42 commits)
KVM: x86: fix sending PV IPI
KVM: x86/mmu: do compare-and-exchange of gPTE via the user address
KVM: x86: Remove redundant vm_entry_controls_clearbit() call
KVM: x86: cleanup enter_rmode()
KVM: x86: SVM: fix tsc scaling when the host doesn't support it
kvm: x86: SVM: remove unused defines
KVM: x86: SVM: move tsc ratio definitions to svm.h
KVM: x86: SVM: fix avic spec based definitions again
KVM: MIPS: remove reference to trap&emulate virtualization
KVM: x86: document limitations of MSR filtering
KVM: x86: Only do MSR filtering when access MSR by rdmsr/wrmsr
KVM: x86/emulator: Emulate RDPID only if it is enabled in guest
KVM: x86/pmu: Fix and isolate TSX-specific performance event logic
KVM: x86: mmu: trace kvm_mmu_set_spte after the new SPTE was set
KVM: x86/svm: Clear reserved bits written to PerfEvtSeln MSRs
KVM: x86: Trace all APICv inhibit changes and capture overall status
KVM: x86: Add wrappers for setting/clearing APICv inhibits
KVM: x86: Make APICv inhibit reasons an enum and cleanup naming
KVM: X86: Handle implicit supervisor access with SMAP
KVM: X86: Rename variable smap to not_smap in permission_fault()
...
This log message was accidentally chopped off.
I was wondering why this happened, but checking the ML log, Mark
precisely followed my suggestion [1].
I just used "..." because I was too lazy to type the sentence fully.
Sorry for the confusion.
[1]: https://lore.kernel.org/all/CAK7LNAR6bXXk9-ZzZYpTqzFqdYbQsZHmiWspu27rtsFxvfRuVA@mail.gmail.com/
Fixes: 4a6795933a ("kbuild: modpost: Explicitly warn about unprototyped symbols")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
-----BEGIN PGP SIGNATURE-----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=F9xx
-----END PGP SIGNATURE-----
Merge tag 'for-5.18/drivers-2022-04-02' of git://git.kernel.dk/linux-block
Pull block driver fix from Jens Axboe:
"Got two reports on nbd spewing warnings on load now, which is a
regression from a commit that went into your tree yesterday.
Revert the problematic change for now"
* tag 'for-5.18/drivers-2022-04-02' of git://git.kernel.dk/linux-block:
Revert "nbd: fix possible overflow on 'first_minor' in nbd_dev_add()"
cros_ec_typec:
* platform/chrome: cros_ec_typec: Check for EC device - Fix a crash when using
the cros_ec_typec driver on older hardware not capable of typec commands.
* Make try power role optional.
* Mux configuration reorganization series from Prashant.
cros_ec_debugfs:
* Fix use after free. Thanks Tzung-bi.
sensorhub:
* cros_ec_sensorhub fixup - Split trace include file
misc:
* Add new mailing list for chrome-platform development.
chrome-platform@lists.linux.dev. Now with patchwork!
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCYkZBeAAKCRBzbaomhzOw
wuUbAP9GaC3906dMf4zucME+icojYFQSeQFMJfS0kMdKBtJROAEArsEilx5aFf7Q
PlyoaaJ7aWpLO3pnUdUNwQM0hJPLGwo=
=me9M
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"cros_ec_typec:
- Check for EC device - Fix a crash when using the cros_ec_typec
driver on older hardware not capable of typec commands
- Make try power role optional
- Mux configuration reorganization series from Prashant
cros_ec_debugfs:
- Fix use after free. Thanks Tzung-bi
sensorhub:
- cros_ec_sensorhub fixup - Split trace include file
misc:
- Add new mailing list for chrome-platform development:
chrome-platform@lists.linux.dev
Now with patchwork!"
* tag 'tag-chrome-platform-for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_debugfs: detach log reader wq from devm
platform: chrome: Split trace include file
platform/chrome: cros_ec_typec: Update mux flags during partner removal
platform/chrome: cros_ec_typec: Configure muxes at start of port update
platform/chrome: cros_ec_typec: Get mux state inside configure_mux
platform/chrome: cros_ec_typec: Move mux flag checks
platform/chrome: cros_ec_typec: Check for EC device
platform/chrome: cros_ec_typec: Make try power role optional
MAINTAINERS: platform-chrome: Add new chrome-platform@lists.linux.dev list
This reverts commit 6d35d04a9e.
Both Gabriel and Borislav report that this commit casues a regression
with nbd:
sysfs: cannot create duplicate filename '/dev/block/43:0'
Revert it before 5.18-rc1 and we'll investigage this separately in
due time.
Link: https://lore.kernel.org/all/YkiJTnFOt9bTv6A2@zn.tnic/
Reported-by: Gabriel L. Somlo <somlo@cmu.edu>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
After being merged, user_events become more visible to a wider audience
that have concerns with the current API.
It is too late to fix this for this release, but instead of a full
revert, just mark it as BROKEN (which prevents it from being selected in
make config). Then we can work finding a better API. If that fails,
then it will need to be completely reverted.
To not have the code silently bitrot, still allow building it with
COMPILE_TEST.
And to prevent the uapi header from being installed, then later changed,
and then have an old distro user space see the old version, move the
header file out of the uapi directory.
Surround the include with CONFIG_COMPILE_TEST to the current location,
but when the BROKEN tag is taken off, it will use the uapi directory,
and fail to compile. This is a good way to remind us to move the header
back.
Link: https://lore.kernel.org/all/20220330155835.5e1f6669@gandalf.local.home
Link: https://lkml.kernel.org/r/20220330201755.29319-1-mathieu.desnoyers@efficios.com
Suggested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While user_events API is under development and has been marked for broken
to not let the API become fixed, move the header file out of the uapi
directory. This is to prevent it from being installed, then later changed,
and then have an old distro user space update with a new kernel, where
applications see the user_events being available, but the old header is in
place, and then they get compiled incorrectly.
Also, surround the include with CONFIG_COMPILE_TEST to the current
location, but when the BROKEN tag is taken off, it will use the uapi
directory, and fail to compile. This is a good way to remind us to move
the header back.
Link: https://lore.kernel.org/all/20220330155835.5e1f6669@gandalf.local.home
Link: https://lkml.kernel.org/r/20220330201755.29319-1-mathieu.desnoyers@efficios.com
Link: https://lkml.kernel.org/r/20220401143903.188384f3@gandalf.local.home
Suggested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
ftrace_graph_is_dead() is used on hot paths, it just reads a variable
in memory and is not worth suffering function call constraints.
For instance, at entry of prepare_ftrace_return(), inlining it avoids
saving prepare_ftrace_return() parameters to stack and restoring them
after calling ftrace_graph_is_dead().
While at it using a static branch is even more performant and is
rather well adapted considering that the returned value will almost
never change.
Inline ftrace_graph_is_dead() and replace 'kill_ftrace_graph' bool
by a static branch.
The performance improvement is noticeable.
Link: https://lkml.kernel.org/r/e0411a6a0ed3eafff0ad2bc9cd4b0e202b4617df.1648623570.git.christophe.leroy@csgroup.eu
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Make sure the event_mutex is properly held during dyn_event_add call.
This is required when adding dynamic events.
Link: https://lkml.kernel.org/r/20220328223225.1992-1-beaub@linux.microsoft.com
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Beau Belgrave <beaub@linux.microsoft.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
kzalloc is a memory allocation function which can return NULL when some
internal memory errors happen. It is safer to add null pointer check.
Link: https://lkml.kernel.org/r/20220329104004.2376879-1-lv.ruyi@zte.com.cn
Cc: stable@vger.kernel.org
Fixes: c1a3c36017 ("proc: bootconfig: Add /proc/bootconfig to show boot config list")
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
When looking for implementation of different phases of the creation of the
TRACE_EVENT() macro, it is pretty useless when all helper macro
redefinitions are in files labeled "stageX_defines.h". Rename them to
state which phase the files are for. For instance, when looking for the
defines that are used to create the event fields, seeing
"stage4_event_fields.h" gives the developer a good idea that the defines
are in that file.
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
If apic_id is less than min, and (max - apic_id) is greater than
KVM_IPI_CLUSTER_SIZE, then the third check condition is satisfied but
the new apic_id does not fit the bitmask. In this case __send_ipi_mask
should send the IPI.
This is mostly theoretical, but it can happen if the apic_ids on three
iterations of the loop are for example 1, KVM_IPI_CLUSTER_SIZE, 0.
Fixes: aaffcfd1e8 ("KVM: X86: Implement PV IPIs in linux guest")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Message-Id: <1646814944-51801-1-git-send-email-lirongqing@baidu.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
FNAME(cmpxchg_gpte) is an inefficient mess. It is at least decent if it
can go through get_user_pages_fast(), but if it cannot then it tries to
use memremap(); that is not just terribly slow, it is also wrong because
it assumes that the VM_PFNMAP VMA is contiguous.
The right way to do it would be to do the same thing as
hva_to_pfn_remapped() does since commit add6a0cd1c ("KVM: MMU: try to
fix up page faults before giving up", 2016-07-05), using follow_pte()
and fixup_user_fault() to determine the correct address to use for
memremap(). To do this, one could for example extract hva_to_pfn()
for use outside virt/kvm/kvm_main.c. But really there is no reason to
do that either, because there is already a perfectly valid address to
do the cmpxchg() on, only it is a userspace address. That means doing
user_access_begin()/user_access_end() and writing the code in assembly
to handle exceptions correctly. Worse, the guest PTE can be 8-byte
even on i686 so there is the extra complication of using cmpxchg8b to
account for. But at least it is an efficient mess.
(Thanks to Linus for suggesting improvement on the inline assembly).
Reported-by: Qiuhao Li <qiuhao@sysec.org>
Reported-by: Gaoning Pan <pgn@zju.edu.cn>
Reported-by: Yongkang Jia <kangel@zju.edu.cn>
Reported-by: syzbot+6cde2282daa792c49ab8@syzkaller.appspotmail.com
Debugged-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Tested-by: Maxim Levitsky <mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Fixes: bd53cb35a3 ("X86/KVM: Handle PFNs outside of kernel reach when touching GPTEs")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
