On multi-function JMicron SATA/PATA/AHCI devices, the PATA controller at
function 1 doesn't work if it is powered on before the SATA controller at
function 0. The result is that PATA doesn't work after resume, and we
print messages like this:
pata_jmicron 0000:02:00.1: Refused to change power state, currently in D3
irq 17: nobody cared (try booting with the "irqpoll" option)
Async resume was introduced in v3.15 by 76569faa62 ("PM / sleep:
Asynchronous threads for resume_noirq"). Prior to that, we powered on
the functions in order, so this problem shouldn't happen.
e6b7e41cdd ("ata: Disabling the async PM for JMicron chip 363/361")
solved the problem for JMicron 361 and 363 devices. With async suspend
disabled, we always power on function 0 before function 1.
Barto then reported the same problem with a JMicron 368 (see comment #57 in
the bugzilla).
Rather than extending the blacklist piecemeal, disable async suspend for
all JMicron multi-function SATA/PATA/AHCI devices.
This quirk could stay in the ahci and pata_jmicron drivers, but it's likely
the problem will occur even if pata_jmicron isn't loaded until after the
suspend/resume. Making it a PCI quirk ensures that we'll preserve the
power-on order even if the drivers aren't loaded.
[bhelgaas: changelog, limit to multi-function, limit to IDE/ATA]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81551
Reported-and-tested-by: Barto <mister.freeman@laposte.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.15+
* pci/host-dra7xx:
PCI: dra7xx: Remove unneeded use of IS_ERR_VALUE()
* pci/host-imx6:
PCI: imx6: Simplify a trivial if-return sequence
* pci/host-spear:
PCI: spear: Use BUG_ON() instead of condition followed by BUG()
Firmware typically configures the PCIe fabric with a consistent Max Payload
Size setting based on the devices present at boot. A hot-added device
typically has the power-on default MPS setting (128 bytes), which may not
match the fabric.
The previous Linux default, in the absence of any "pci=pcie_bus_*" options,
was PCIE_BUS_TUNE_OFF, in which we never touch MPS, even for hot-added
devices.
Add a new default setting, PCIE_BUS_DEFAULT, in which we make sure every
device's MPS setting matches the upstream bridge. This makes it more
likely that a hot-added device will work in a system with optimized MPS
configuration.
Note that if we hot-add a device that only supports 128-byte MPS, it still
likely won't work because we don't reconfigure the rest of the fabric.
Booting with "pci=pcie_bus_peer2peer" is a workaround for this because it
sets MPS to 128 for everything.
[bhelgaas: changelog, new default, rework for pci_configure_device() path]
Tested-by: Keith Busch <keith.busch@intel.com>
Tested-by: Jordan Hargrave <jharg93@gmail.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Previously we checked for invalid MPS settings, i.e., a device with MPS
different than its upstream bridge, in pcie_bus_detect_mps(). We only did
this if the arch or hotplug driver called pcie_bus_configure_settings(),
and then only if PCIe bus tuning was disabled (PCIE_BUS_TUNE_OFF).
Move the MPS checking code to pci_configure_device(), so we do it in the
pci_device_add() path for every device.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
of_parse_phandle() returns a device_node pointer with the refcount
incremented. We should dispose of this reference when we're finished.
Drop the reference acquired by of_parse_phandle().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The pcibios_msi_controller() hook was only implemented by ARM, and it sets
pci_bus->msi now, so it doesn't need this hook anymore.
Remove the unused pcibios_msi_controller() hook.
[bhelgaas: changelog, split into separate patch]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ARM now uses pci_bus->msi to store the msi_controller pointer, so we don't
need to save it in struct pci_sys_data, and we don't need to implement
pcibios_msi_controller() to get it out of pci_sys_data.
Remove msi_controller from struct pci_sys_data and
pcibios_msi_controller().
[bhelgaas: changelog, split into separate patch]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
ARM previously stored the msi_controller pointer in its sysdata, struct
pci_sys_data, and implemented pcibios_msi_controller() to retrieve it.
That made PCI host controller drivers specific to ARM because they had to
put the msi_controller pointer in the ARM-specific pci_sys_data.
There is now a generic mechanism, pci_scan_root_bus_msi(), for giving the
msi_controller pointer to the PCI core. Use this for all ARM systems and
for the DesignWare and Xilinx PCI host controller drivers.
This removes an ARM dependency from the DesignWare, DRA7xx, EXYNOS, i.MX6,
Keystone, Layerscape, SPEAr13xx, and Xilinx drivers.
[bhelgaas: changelog, split into separate patch]
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Simon Horman <horms@verge.net.au>
CC: Russell King <linux@arm.linux.org.uk>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Marc Zyngier <marc.zyngier@arm.com>
Add a pci_scan_root_bus_msi() interface so an arch can specify the MSI
controller up front. This removes the need for a pcibios callback to set
the MSI controller later.
This is not exported because I'd like to replace the variety of "scan root
bus" interfaces with a single, more extensible interface that can handle
the MSI controller, domain, pci_ops, resources, etc. I hope this interface
is temporary.
[bhelgaas: changelog, split into separate patch]
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
In the ARM PCI bios32 layer, failures to dynamically allocate pci_sys_data
for a PCI bus, or a PCI bus scan failure have to be considered serious
warnings but they should not trigger a system panic so that at least the
system is given a chance to be debugged.
This patch replaces the panic statements with WARN() messages to improve
error reporting in the ARM PCI bios32 layer.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Marc Zyngier <marc.zyngier@arm.com>
Make pci-host-generic driver (kernel option PCI_HOST_GENERIC) available on
arm64.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ARM64 requires setup-irq.o to provide pci_fixup_irqs() implementation. We
are adding this now to support the pci-host-generic host controller, but we
enable it for ARM64 PCI so that other host controllers can use this as
well.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The generic OF-based host controller driver uses pci_common_init_dev(),
which is ARM-specific and requires the ARM struct hw_pci. The part of
pci_common_init_dev() that is needed is limited and can be done here
without using hw_pci.
Note that the ARM pcibios functions expect the PCI sysdata to be a pointer
to a struct pci_sys_data. Add a struct pci_sys_data as the first element
in struct gen_pci so that when we use a gen_pci pointer as sysdata, it is
also a pointer to a struct pci_sys_data.
Create and scan the root bus directly without using the ARM
pci_common_init_dev() interface.
[bhelgaas: changelog, move pcie_bus_configure_settings() before
pci_bus_add_devices(), combine !PCI_PROBE_ONLY blocks]
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Simplify a trivial if-return sequence by combining it with a preceding
function call.
The semantic patch that makes this change is available in
scripts/coccinelle/misc/simple_return.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Lucas Stach <l.stach@pengutronix.de>
Use BUG_ON() instead of an if condition followed by BUG().
The semantic patch that makes this change is available in
scripts/coccinelle/misc/bugon.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
There is no need to use the IS_ERR_VALUE() macro for checking the return
value from pm_runtime_* functions.
Test for a negative pm_runtime_get_sync() return value instead of using
IS_ERR_VALUE().
The semantic patch that makes this change is available in
scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
* pci/host-dra7xx:
ARM: dts: am57xx-evm: Add 'gpios' property with gpio2_8
PCI: dra7xx: Add support to make GPIO drive PERST# line
PCI: dra7xx: Clear MSE bit during suspend so clocks will idle
PCI: dra7xx: Add PM support
PCI: dra7xx: Disable pm_runtime on get_sync failure
* pci/host-iproc:
PCI: iproc: Allow BCMA bus driver to be built as module
PCI: iproc: Add arm64 support
PCI: iproc: Delete unnecessary checks before phy calls
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
Remove pci_ats_enabled(). There are no callers outside the ATS code
itself. We don't need to check ats_cap, because if we don't find an ATS
capability, we'll never set ats_enabled.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Stop caching the Invalidate Queue Depth in struct pci_dev.
pci_ats_queue_depth() is typically called only once per device, and it
returns a fixed value per-device, so callers who need the value frequently
can cache it themselves.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Move ATS declarations to linux/pci.h so they're all in one place.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
There's no need to BUG() if we enable ATS when it's already enabled. We
don't need to BUG() when disabling ATS on a device that doesn't support ATS
or if it's already disabled. If ATS is enabled, certainly we found an ATS
capability in the past, so it should still be there now.
Clean up these error paths.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Use the pci_physfn() helper rather than looking up physfn by hand.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The ATS setup code in ats_alloc_one() is only used by pci_ats_init(), so
inline it there. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
We previously returned -ENODEV for devices that don't support ATS (except
that we always returned 0 for VFs, whether or not they support ATS).
For consistency, always return -EINVAL (not -ENODEV) if the device doesn't
support ATS. Return zero for VFs that support ATS.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The extended capabilities list is linked with 12-bit pointers, and the ATS
Smallest Translation Unit and Invalidate Queue Depth fields are both 5
bits.
Use u16 and u8 to hold the extended capability address and the stu and qdep
values. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The pci_ats struct is small and will get smaller, so I don't think it's
worth allocating it separately from the pci_dev struct.
Embed the ATS fields directly into struct pci_dev.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Previously, we allocated pci_ats structures when an IOMMU driver called
pci_enable_ats(). An SR-IOV VF shares the STU setting with its PF, so when
enabling ATS on the VF, we allocated a pci_ats struct for the PF if it
didn't already have one. We held the sriov->lock to serialize threads
concurrently enabling ATS on several VFS so only one would allocate the PF
pci_ats.
Gregor reported a deadlock here:
pci_enable_sriov
sriov_enable
virtfn_add
mutex_lock(dev->sriov->lock) # acquire sriov->lock
pci_device_add
device_add
BUS_NOTIFY_ADD_DEVICE notifier chain
iommu_bus_notifier
amd_iommu_add_device # iommu_ops.add_device
init_iommu_group
iommu_group_get_for_dev
iommu_group_add_device
__iommu_attach_device
amd_iommu_attach_device # iommu_ops.attach_device
attach_device
pci_enable_ats
mutex_lock(dev->sriov->lock) # deadlock
There's no reason to delay allocating the pci_ats struct, and if we
allocate it for each device at enumeration-time, there's no need for
locking in pci_enable_ats().
Allocate pci_ats struct during enumeration, when we initialize other
capabilities.
Note that this implementation requires ATS to be enabled on the PF first,
before on any of the VFs because the PF controls the STU for all the VFs.
Link: http://permalink.gmane.org/gmane.linux.kernel.iommu/9433
Reported-by: Gregor Dick <gdick@solarflare.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
gpio2_8 is connected to the PCIe_RESETn line and it has to be driven low to
reset the PCIe cards. Add gpios property to PCIe DT node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The PERST# line in am57x-evm is connected to a GPIO line and PERST# should
be driven high to indicate the clocks are stable (As per Figure 2-10: Power
Up of the PCIe CEM spec 3.0).
Add support to make GPIO drive PERST# line.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
DRA7xx requires the MSE bit to be cleared to set the master in standby
mode. (In DRA7xx TRM_vE, section 24.9.4.5.2.2.1 PCIe Controller Master
Standby Behavior advises to use the clearing of the local MSE bit to set
the master in standby. Without this some of the clocks do not idle).
Clear the MSE bit on suspend and enable it on resume. Clearing MSE bit is
required to get clocks to be idled after suspend.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Add PM support to pci-dra7xx so PCI clocks can be disabled during suspend
and enabled during resume without affecting PCI functionality.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Fix the error handling when pm_runtime_get_sync() fails.
If pm_runtime_get_sync() fails, call pm_runtime_disable() so there are no
unbalanced pm_runtime_enable() calls.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Change CONFIG_PCIE_IPROC_BCMA to tristate to make it possible to build this
driver as a module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ray Jui <rjui@broadcom.com>
The Intel 100-series chipset now includes the integrated Ethernet as part
of a multifunction package. The Ethernet function does not include native
ACS support, but Intel confirms that the device is not capable of peer-to-
peer within the package. We can therefore quirk it to expose the
isolation.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: John Ronciak <john.ronciak@gmail.com>
set_irq_flags is ARM-specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in .map()
functions, and we can simply remove the set_irq_flags calls. Some users
also modify IRQ_NOPROBE, and this has been maintained although it is not
clear that is really needed. There appears to be a great deal of blind
copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Michal Simek <michal.simek@xilinx.com>
CC: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
We queued interrupt events for the MRL being opened or closed, but the code
in interrupt_event_handler() that handles these events ignored them.
Stop enabling MRL interrupts and remove the ignored events.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The list of interrupt events (INT_BUTTON_IGNORE, INT_PRESENCE_ON, etc.) was
copied from other hotplug drivers, but pciehp doesn't use them all.
Remove the interrupt events that aren't used by pciehp.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's platform-dependent, but an MMIO read to a non-existent PCI device
generally returns data with all bits set. This happens when the host
bridge or Root Complex times out waiting for a response from the device and
fabricates return data to complete the CPU's read.
One example, reported in the bugzilla below, involved this hierarchy:
pci 0000:00:1c.0: PCI bridge to [bus 02-3a] Root Port
pci 0000:02:00.0: PCI bridge to [bus 03-0a] Upstream Port
pci 0000:03:03.0: PCI bridge to [bus 05-07] Downstream Port
pci 0000:05:00.0: PCI bridge to [bus 06-07] Thunderbolt Upstream Port
pci 0000:06:00.0: PCI bridge to [bus 07] Thunderbolt Downstream Port
pci 0000:07:00.0: BCM57762 NIC
Unplugging the Thunderbolt switch and the NIC below it resulted in this:
pciehp 0000:03:03.0: Surprise Removal
tg3 0000:07:00.0: tg3_abort_hw timed out, TX_MODE_ENABLE will not clear MAC_TX_MODE=ffffffff
pciehp 0000:06:00.0: unloading service driver pciehp
pciehp 0000:06:00.0: pcie_isr: intr_loc 11f
pciehp 0000:06:00.0: Switch interrupt received
pciehp 0000:06:00.0: Latch open on Slot
pciehp 0000:06:00.0: Attention button interrupt received
pciehp 0000:06:00.0: Button pressed on Slot
pciehp 0000:06:00.0: Presence/Notify input change
pciehp 0000:06:00.0: Card present on Slot
pciehp 0000:06:00.0: Power fault interrupt received
pciehp 0000:06:00.0: Data Link Layer State change
pciehp 0000:06:00.0: Link Up event
The pciehp driver correctly noticed that the Thunderbolt switch (05:00.0
and 06:00.0) and NIC (07:00.0) had been removed, and it called their driver
remove methods.
Since the NIC was already gone, tg3 received 0xffffffff when it tried to
read from the device. The resulting timeout is a tg3 issue and not of
interest here.
Similarly, since the 06:00.0 Thunderbolt switch was already gone,
pcie_isr() received 0xffff when it tried to read PCI_EXP_SLTSTA, and pciehp
thought that was valid status showing that many events had happened: the
latch had been opened, the attention button had been pressed, a card was
now present, and the link was now up. These are all wrong, of course, but
pciehp went on to try to power up and enumerate devices below the
non-existent bridge:
pciehp 0000:06:00.0: PCI slot - powering on due to button press
pciehp 0000:06:00.0: Surprise Insertion
pci 0000:07:00.0 id reading try 50 times with interval 20 ms to get ffffffff
[bhelgaas: changelog, also check in pcie_poll_cmd() & pcie_do_write_cmd()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99841
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/irq:
PCI/MSI: Free legacy IRQ when enabling MSI/MSI-X
PCI: Add helpers to manage pci_dev->irq and pci_dev->irq_managed
PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()
PCI: Add pcibios_alloc_irq() and pcibios_free_irq()
* pci/misc:
PCI: Remove unused "pci_probe" flags
PCI: Add VPD function 0 quirk for Intel Ethernet devices
PCI: Add dev_flags bit to access VPD through function 0
PCI / ACPI: Fix pci_acpi_optimize_delay() comment
PCI: Remove a broken link in quirks.c
PCI: Remove useless redundant code
PCI: Simplify pci_find_(ext_)capability() return value checks
PCI: Move PCI_FIND_CAP_TTL to pci.h and use it in quirks
PCI: Add pcie_downstream_port() (true for Root and Switch Downstream Ports)
PCI: Fix pcie_port_device_resume() comment
PCI: Shift PCI_CLASS_NOT_DEFINED consistently with other classes
PCI: Revert aeb30016fe ("PCI: add Intel USB specific reset method")
PCI: Fix TI816X class code quirk
PCI: Fix generic NCR 53c810 class code quirk
PCI: Use PCI_CLASS_SERIAL_USB instead of bare number
PCI: Add quirk for Intersil/Techwell TW686[4589] AV capture cards
PCI: Remove Intel Cherrytrail D3 delays
* pci/resource:
PCI: Call pci_read_bridge_bases() from core instead of arch code
* pci/virtualization:
PCI: Restore ACS configuration as part of pci_restore_state()
* pci/host-designware:
PCI: designware: Don't complain missing *config* reg space if va_cfg0 is set
* pci/host-xgene:
PCI: xgene: Add support for a 64-bit prefetchable memory window
arm64: dts: Add APM X-Gene PCIe 64-bit prefetchable window
PCI: xgene: Drop owner assignment from platform_driver
* pci/host-xilinx:
PCI: xilinx: Check for MSI interrupt flag before handling as INTx
Previously, pci_setup_device() and similar functions searched the
pci_bus->slots list without any locking. It was possible for another
thread to update the list while we searched it.
Add pci_dev_assign_slot() to search the list while holding pci_slot_mutex.
[bhelgaas: changelog, fold in CONFIG_SYSFS fix]
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rajat Jain reported a deadlock when PCIe hot-add and AER recovery happen at
the same time:
thread 1:
pciehp_enable_slot
pciehp_configure_device
pci_bus_add_devices
pci_bus_add_device
device_attach
device_lock(dev) # acquire device lock
...
pciehp_probe
init_slot
pci_hp_register
pci_create_slot
down_write(pci_bus_sem) # deadlock here
thread 2:
aer_isr_one_error
aer_process_err_device
do_recovery
broadcast_error_message(..., report_error_detected)
pci_walk_bus(..., cb=report_error_detected, ...)
down_read(&pci_bus_sem) # acquire pci_bus_sem
report_error_detected(dev) # cb()
device_lock(dev) # deadlock here
Previously, the bus->devices and bus->slots list were protected by
pci_bus_sem. In pci_create_slot(), we held it for writing so we could
add to the bus->slots list.
Add a new local pci_slot_mutex to protect bus->slots. Hold pci_bus_sem for
reading while searching the bus->devices list.
[bhelgaas: changelog]
Link: http://lkml.kernel.org/r/CAA93t1qpPqbih+UB0McA_d_+2rVaNkXsinAUxYzK9+JXSS+L-g@mail.gmail.com
Reported-by: Rajat Jain <rajatja@google.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Once MSI/MSI-X is enabled by the device driver, a PCI device won't use
legacy IRQs again until MSI/MSI-X is disabled.
Call pcibios_free_irq() when enabling MSI/MSI-X and pcibios_alloc_irq()
when disabling MSI/MSI-X. This allows arch code to manage resources
associated with the legacy IRQ.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Add pci_has_managed_irq(), pci_set_managed_irq(), and
pci_reset_managed_irq() to simplify code. No functional change.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
To support IOAPIC hotplug, we need to allocate PCI IRQ resources on demand
and free them when not used anymore.
Implement pcibios_alloc_irq() and pcibios_free_irq() to dynamically
allocate and free PCI IRQs.
Remove mp_should_keep_irq(), which is no longer used.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Add pcibios_alloc_irq() and pcibios_free_irq(), which are called when
binding/unbinding PCI device drivers.
PCI arch code may implement these to manage IRQ resources for hotplugged
devices.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
The following flags are only used on x86, but they got copied to FR-V,
MN10300, and SuperH:
PCI_PROBE_BIOS
PCI_PROBE_CONF1
PCI_PROBE_CONF2
PCI_ASSIGN_ROMS
PCI_NO_CHECKS
PCI_BIOS_IRQ_SCAN
PCI_ASSIGN_ALL_BUSSES
FR-V and MN10300 do test for PCI_ASSIGN_ROMS, but they never set it, so
it's dead code.
Remove the unused flags above.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When we scan a PCI bus, we read PCI-PCI bridge window registers with
pci_read_bridge_bases() so we can validate the resource hierarchy. Most
architectures call pci_read_bridge_bases() from pcibios_fixup_bus(), but
PCI-PCI bridges are not arch-specific, so this doesn't need to be in
arch-specific code.
Call pci_read_bridge_bases() directly from the PCI core instead of from
arch code.
For alpha and mips, we now call pci_read_bridge_bases() always; previously
we only called it if PCI_PROBE_ONLY was set.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: James E.J. Bottomley <jejb@parisc-linux.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Howells <dhowells@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Tony Luck <tony.luck@intel.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Michal Simek <monstr@monstr.eu>
CC: Chris Zankel <chris@zankel.net>
