This series adds support the other two AIFs present in the sun8i codec,
which can be used for codec2codec DAI links.
This series first fills out the DAI driver, removing assumptions that
were made for AIF1 (16 bits, 2 channels, certain clock inversions). Some
new logic is required to handle 3 DAIs and the ADC/DAC sharing the same
clock. Finally, it adds the new DAIs, and hooks them up with DAPM
widgets and routes per the hardware topology.
To minimize the number of patches in this series, related device tree
patches (increasing #sound-dai-cells, adding new DAI links) will be sent
separately.
Changes from v1:
- Patches 1-8 from v1 (DAPM changes) were merged
- Prefixed AIF constants with "SUN8I_CODEC_" [1, 7, 10, 16, 17]
- Renamed variables in sun8i_codec_set_fmt for clarity [3]
- Update sysclk->sysclk_rate if later calls to hw_params change the
sample rate (thanks Chen-Yu for reminding me of this) [11]
- Select COMMON_CLK for clk_set_rate_exclusive [12]
- Add comments and hopefully clarify the clock protection logic [12]
- Make the error message more concise and put it on one line [12]
- Drop the "reg" variable holding SUN8I_AIF_CLK_CTRL(dai->id) [15]
- Rename "div_reg" to "clk_reg" and adjust comments for clarity [17]
- Improve the AIF2/AIF3 rate mismatch error message [17]
- Minor grammar/wording fixes in commit messages [2, 4, 7, 8, 16, 17]
- Added Maxime's Acked-by: [1-2, 4-9, 11, 13-14, 16]
Samuel Holland (17):
ASoC: sun8i-codec: Prepare to extend the DAI driver
ASoC: sun8i-codec: Program DAI format before clock inversion
ASoC: sun8i-codec: Enable all supported clock inversions
ASoC: sun8i-codec: Use the provided word size
ASoC: sun8i-codec: Round up the LRCK divisor
ASoC: sun8i-codec: Correct the BCLK divisor calculation
ASoC: sun8i-codec: Support the TDM slot binding
ASoC: sun8i-codec: Enforce symmetric DAI parameters
ASoC: sun8i-codec: Enable all supported sample rates
ASoC: sun8i-codec: Automatically set the system sample rate
ASoC: sun8i-codec: Constrain to compatible sample rates
ASoC: sun8i-codec: Protect the clock rate while streams are open
ASoC: sun8i-codec: Require an exact BCLK divisor match
ASoC: sun8i-codec: Enable all supported PCM formats
ASoC: sun8i-codec: Generalize AIF clock control
ASoC: sun8i-codec: Add the AIF2 DAI, widgets, and routes
ASoC: sun8i-codec: Add the AIF3 DAI, widgets, and routes
sound/soc/sunxi/Kconfig | 1 +
sound/soc/sunxi/sun8i-codec.c | 834 ++++++++++++++++++++++++++++------
2 files changed, 699 insertions(+), 136 deletions(-)
--
2.26.2
Add 88200Hz and 176400Hz sample rates support for TX.
Add 88200Hz, 176400Hz, 192000Hz sample rates support for RX.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/1602557360-18795-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On i.MX8QM, there are separate interrupts for TX and RX.
As the EDMA can't be configured to swing back to first FIFO
after writing the second FIFO, so we need to force the burst
size to be 2 on i.MX8QM. And EDMA don't support to shift
the data from S24_LE to S16_LE, so the supported TX format
is also different on i.MX8QM.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/1602739728-4433-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP supports different audio configurations other than I2S.
This patch will fix acp driver probe failure for other audio
configurations.
Tested-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/1603476441-3506-1-git-send-email-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the two-step copy-and-convert in
wm5102_out_comp_coeff_put() with get_unaligned_be16(). Apart from
looking nicer, it avoids this sparse warning:
wm5102.c:687:35: sparse: sparse: cast to restricted __be16
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20201015102703.24622-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the STM32 SAI bindings to DT schema format using json-schema.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201009141051.27365-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The change removes the platform_data include/definition. It only contains
some values for the MICBIAS.
These are moved into 'dt-bindings/sound/adi,adau1977.h' so that they can be
used inside device-trees. When moving then, they need to be converted to
pre-compiler defines, so that the DT compiler can understand them.
The driver then, also needs to include the new
'dt-bindings/sound/adi,adau1977.h' file.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201019105313.24862-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The TI PCM5102A codec driver can be used with the generic sound card
drivers, so it should be selectable. For example, with the addition
of #sound-dai-cells = <0> property in DT, it can be used with simple/graph
card drivers.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20201012141911.3150996-1-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All platforms that use the jz4740-i2s driver have been switched to
devicetree for a while now and the assignment of the DMA peripheral ID
is done in the devicetree.
It is no longer necessary to manually assign the peripheral ID in the
driver, so remove that. The DMA driver does not even look at the value
assigned in the driver anymore and always uses the value provided by the
devicetree.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201023092346.5777-1-lars@metafoo.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Device tree audio configuration for STM32 DFSDM is already
covered in the following binding:
Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml
Remove stm32-adfsdm.txt obsolete binding.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201020155709.2621-3-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace commas with semicolons. What is done is essentially described by
the following Coccinelle semantic patch (http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1602407979-29038-8-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace commas with semicolons. What is done is essentially described by
the following Coccinelle semantic patch (http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/1602407979-29038-7-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace commas with semicolons. What is done is essentially described by
the following Coccinelle semantic patch (http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/1602407979-29038-4-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace commas with semicolons. What is done is essentially described by
the following Coccinelle semantic patch (http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1602407979-29038-2-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
AIF3 has some differences from AIF1 and AIF2:
- It supports one channel only
- It supports master mode only
- It is not directly connected to any of the mixers; instead all audio
goes through a mux with AIF2.
- It does not have its own clock dividers; instead it reuses AIF2 BCLK
and LRCK. This means that when both AIF2 and AIF3 are active, they
must use the same sample rate and total frame width. Since AIF2 and
AIF3 are only used for codec2codec DAI links, constraints are not
applicable here; the only thing we can do when the rates don't match
is report an error.
Make the necessary adjustments to support this AIF.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20201014061941.4306-18-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for AIF2, which is stereo and has fullly independent
clocking capability, making it very similar to AIF1.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20201014061941.4306-17-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The AIF clock control register has the same layout for all three AIFs.
The only difference between them is that AIF3 is missing some fields. We
can reuse the same register field definitions for all three registers,
and use the DAI ID to select the correct register address.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201014061941.4306-16-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the DAI clock setup is correct for all hardware-supported PCM
formats, we can enable them in the driver. With the appropriate support
in the CPU DAI driver, this allows userspace to access the additional
formats.
Since this codec is connected to the CPU via a DAI, not directly, we do
not care if the CPU DAI is using 3-byte or 4-byte formats, so we can
support them both.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20201014061941.4306-15-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we guarantee that SYSCLK is running at the optimal rate when
hw_params succeeds, and that it will continue running at that rate,
SYSCLK will always be an integer multiple of BCLK. So we can always
pick the exact divider, not just the closest divider.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20201014061941.4306-14-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec's clock input is shared among all AIFs, and shared with other
audio-related hardware in the SoC, including I2S and SPDIF controllers.
To ensure sample rates selected by userspace or by codec2codec DAI links
are maintained, the clock rate must be protected while it is in use.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201014061941.4306-13-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
While another stream is active, only allow userspace to use sample rates
that are compatible with the current SYSCLK frequency. This ensures the
actual sample rate will always match what is given in hw_params.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20201014061941.4306-12-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The sun8i codec has three clock/sample rate domains:
- The AIF1 domain, with a sample rate equal to AIF1 LRCK
- The AIF2 domain, with a sample rate equal to AIF2 LRCK
- The SYSCLK domain, containing the ADC, DAC, and effects (AGC/DRC),
with a sample rate given by a divisor from SYSCLK. The divisor is
controlled by the AIF1_FS or AIF2_FS field in SYS_SR_CTRL, depending
on if SYSCLK's source is AIF1CLK or AIF2CLK, respectively. The exact
sample rate depends on if SYSCLK is running at 22.6 MHz or 24.6 MHz.
When an AIF (currently only AIF1) is active, the ADC and DAC should run
at that sample rate to avoid artifacting. Sample rate conversion is only
available when multiple AIFs are active and are routed to each other;
this means the sample rate conversion hardware usually cannot be used.
Only attach the event hook to the channel 0 AIF widgets, since we only
need one event when a DAI stream starts or stops. Channel 0 is always
brought up with a DAI stream, regardless of the number of channels in
the stream.
The ADC and DAC (along with their effects blocks) can be used even if
no AIFs are in use. In that case, we should select an appropriate sample
rate divisor, instead of keeping the last-used AIF sample rate.
44.1/48 kHz was chosen to balance audio quality and power consumption.
Since the sample rate is tied to active AIF paths, disabling pmdown_time
allows switching to the optimal sample rate immediately, instead of
after a 5 second delay.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201014061941.4306-11-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The system sample rate programmed into the hardware is really a clock
divider from SYSCLK to the ADC and DAC. Since we support two SYSCLK
frequencies, we can use all sample rates corresponding to one of those
frequencies divided by any available divisor.
This commit enables support for those sample rates. It also stops
advertising support for a 64 kHz sample rate, which is not supported.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20201014061941.4306-10-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The AIFs have a single register controlling DAI parameters in both
directions, including BCLK/LRCK divisor and word size. The DAIs produce
only noise or silence if any of these parameters is wrong. Therefore, we
need to enforce symmetry for these parameters, so starting a new
substream will not break an existing substream.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20201014061941.4306-9-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that BCLK and LRCK rate calculations in the driver can handle any
hardware-supported slot width and number of slots, allow overriding
those parameters from the device tree.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20201014061941.4306-8-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, the BCLK divisor calculation assumed zero padding and
exactly two slots. In order to support the TDM slot binding and
20/24-bit word sizes, those assumptions must be removed.
Due to hardware limitations, the BCLK/LRCK ratio is not as simple as
"slot_width * slots". However, the correct value is already calculated
elsewhere in this function, since it must also be programmed into the
hardware. Reuse that value to calculate the correct SYSCLK/BCLK divisor.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20201014061941.4306-7-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec supports only power-of-two BCLK/LRCK divisors. If either the
slot width or the number of slots is not a power of two, the LRCK
divisor must be rounded up to provide enough space. To do that, use
order_base_2 (instead of ilog2, which rounds down).
Since the rounded divisor is also needed for setting the SYSCLK/BCLK
divisor, return the order base 2 instead of fully calculating the
hardware register encoding.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20201014061941.4306-6-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The hardware supports 8 to 24-bit word sizes on all three of its DAIs,
only one of which is connected to the CPU DAI. Program the word size
based on the actual selected format, instead of assuming limitations
from another driver (which, incedentally, has patches pending to remove
that limitation).
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20201014061941.4306-5-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the I2S, LEFT_J, or RIGHT_J format, the hardware supports
independent BCLK and LRCK inversion control. When using DSP_A or DSP_B,
LRCK inversion is not supported. The register bit is repurposed to
select between DSP_A and DSP_B. Extend the driver to support this.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201014061941.4306-4-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The LRCK inversion bit has a different meaning in DSP mode: it selects
between the DSP A and DSP B formats. To support this, we need to know if
the selected format is a DSP format. One easy way to do this is to set
the format field before the clock inversion fields.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20201014061941.4306-3-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for adding additional DAIs to this component, convert the
DAI driver definition to an array. Since this changes all of the lines
in the definition anyway, let's move it closer to the ops function
definitions, instead of on the far side of the DAPM arrays. And while
moving the DAI driver ops, rename the set_fmt hook to match the usual
naming scheme.
Give the existing DAI an explicit ID and more meaningful stream names,
so it will remain unique as more DAIs are added. The AIF widget streams
must be updated to match.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20201014061941.4306-2-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace". So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 453431a549 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.
Since then a few more instances of kzfree() have slipped in.
Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.
If GIT_DIR is unset, keep using the current ".git" default.
Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
which are based on CLOCK_MONOTONIC require time namespace corrected. This
was missed in the original time namesapce support.
-----BEGIN PGP SIGNATURE-----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=VFCv
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A time namespace fix and a matching selftest. The futex absolute
timeouts which are based on CLOCK_MONOTONIC require time namespace
corrected. This was missed in the original time namesapce support"
* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
selftests/timens: Add a test for futex()
futex: Adjust absolute futex timeouts with per time namespace offset
- A trivial build fix for sched_feat() to compile correctly with
CONFIG_JUMP_LABEL=n
- Replace a zero lenght array with a flexible array.
-----BEGIN PGP SIGNATURE-----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=RNOk
-----END PGP SIGNATURE-----
Merge tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"Two scheduler fixes:
- A trivial build fix for sched_feat() to compile correctly with
CONFIG_JUMP_LABEL=n
- Replace a zero lenght array with a flexible array"
* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/features: Fix !CONFIG_JUMP_LABEL case
sched: Replace zero-length array with flexible-array
source bitmask of perf events correctly.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAl+ViWwTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoZwlD/4voY9SOqJrHyP9qPVhEBpUyevd+q+m
gwzBa1s5MQ0L9hyxGFVZ1QrJP6t02yapHjOe05p4xw4Re71mJ1uSXFtRHiLYEcRz
6pdQMEfY7oyzYGXprxQFmDF4skB33UNqDt+MVAC29MpWuQB+JEzSqHfXKrZrLuts
98wNtQllH5FgIJ//yShe7eUBSkdZZgKQVfp56Bv6SaoCEksIBb1U9KRmL4XeLPJI
ha8w+bDx34KiA0AELiojc6pNT8CLtRRY7lt5y0/qjmdEgx68ER3nl5lvHnpAJjwP
4p0YYxNXpZdXdDgOIP9Nbt1LAYUWhZbJwi15N3VlPxZWfSiBAXijN32BRz448CX6
dZ4NRt5TucAchqokHM5J16fkaRChU16gUjjrnUjh2nzp/XrmUxXBqD7kAdC5TrE6
qOLbo1S4O7tx4frvO1WFeY1v4yy5f6edW8/7+pLl86+flGWFhe8NEtc9Pv3uV6JW
9YHmfy8uoOauhxaKxhuonGW+xPEsPupd04on3Nz/O4bEPmD6hGHp8VxEbzP0p3Gl
NTxelO10s4Jgn29oKSRcRl8VUN3F16/lbUXuqSvgm77x+2a0pZ0vl8VQ6tVQh5fk
HFJMkrib2VVixb5l3U11aTgbtUBVOegfIbeF4HTTgVFY+1suRCOMI4dJNDGf3TIa
q9fdotu+TtAYXQ==
=vvcT
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fix from Thomas Gleixner:
"A single fix to compute the field offset of the SNOOPX bit in the data
source bitmask of perf events correctly"
* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: correct SNOOPX field offset
-----BEGIN PGP SIGNATURE-----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=YIEm
-----END PGP SIGNATURE-----
Merge tag 'ntb-5.10' of git://github.com/jonmason/ntb
Pull NTB fixes from Jon Mason.
* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
NTB: Use struct_size() helper in devm_kzalloc()
ntb: intel: Fix memleak in intel_ntb_pci_probe
NTB: hw: amd: fix an issue about leak system resources
Pull i2c fix from Wolfram Sang:
"Regression fix for rc1 and stable kernels as well"
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs
-----BEGIN PGP SIGNATURE-----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=4LDZ
-----END PGP SIGNATURE-----
Merge tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more cifs updates from Steve French:
"Add support for stat of various special file types (WSL reparse points
for char, block, fifo)"
* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number
smb3: add some missing definitions from MS-FSCC
smb3: remove two unused variables
smb3: add support for stat of WSL reparse points for special file types
