Pull libata ZAC support from Tejun Heo:
"This contains Zone ATA Command support for Shingled Magnetic Recording
devices.
In addition to sending the new commands down to the device, as ZAC
commands depend on getting a lot of responses from the device, piping
up responses is beefed up too. However, it doesn't involve changes to
libata core mechanism or its interaction with upper layers, so I'm not
expecting too many fallouts.
Kudos to Hannes for driving SMR support"
* 'for-4.7-zac' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (28 commits)
libata: support host-aware and host-managed ZAC devices
libata: support device-managed ZAC devices
libata: NCQ encapsulation for ZAC MANAGEMENT OUT
libata: Implement ZBC OUT translation
libata: implement ZBC IN translation
libata: fixup ZAC device disabling
libata-scsi: Generate sense code for disabled devices
libata-trace: decode subcommands
libata: Check log page directory before accessing pages
libata: Add command definitions for NCQ Encapsulation for READ LOG DMA EXT
libata: Separate out ata_dev_config_ncq_send_recv()
libata/libsas: Define ATA_CMD_NCQ_NON_DATA
libsas: enable FPDMA SEND/RECEIVE
libata: do not attempt to retrieve sense code twice
libata-scsi: Set information sense field for invalid parameter
libata-scsi: set bit pointer for sense code information
libata-scsi: Set field pointer in sense code
scsi: add scsi_set_sense_field_pointer()
libata: Implement control mode page to select sense format
libata-scsi: generate correct ATA pass-through sense
...
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
This patch includes the usual quota of driver updates (bnx2fc, mp3sas,
hpsa, ncr5380, lpfc, hisi_sas, snic, aacraid, megaraid_sas) there's
also a multiqueue update for scsi_debug, assorted bug fixes and a few
other minor updates (refactor of scsi_sg_pools into generic code, alua
and VPD updates, and struct timeval conversions).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJXO8W0AAoJEDeqqVYsXL0MW24H/jGWwfjsDUiSsLwbLca6DWu8
ZCWZ7rSZ27CApwGPgZGpLvUg+vpW8Ykm2zdeBnlZ6ScXS+dT3uo/PHsnemsTextj
6glQNIOFY0Ja2GwkkN00M6IZQhTJ628cqJKIEJxC68lIw16wiOwjZaK68GMrusDO
Sl062rkuLR6Jb2T+YoT/sD8jQfWlSj2V9e9rqJoS/rIbS6B+hUipuybz2yQ2yK2u
XFc30yal9oVz1fHEoh2O8aqckW3/iskukVXVuZ0MQzT/lV/bm9I6AnWVHw7d0Yhp
ZELjXpjx5M2Z/d8k0Wvx1e25oL/ERwa96yLnTvRcqyF5Yt1EgAhT+jKvo4pnGr8=
=L6y/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"First round of SCSI updates for the 4.6+ merge window.
This batch includes the usual quota of driver updates (bnx2fc, mp3sas,
hpsa, ncr5380, lpfc, hisi_sas, snic, aacraid, megaraid_sas). There's
also a multiqueue update for scsi_debug, assorted bug fixes and a few
other minor updates (refactor of scsi_sg_pools into generic code, alua
and VPD updates, and struct timeval conversions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (138 commits)
mpt3sas: Used "synchronize_irq()"API to synchronize timed-out IO & TMs
mpt3sas: Set maximum transfer length per IO to 4MB for VDs
mpt3sas: Updating mpt3sas driver version to 13.100.00.00
mpt3sas: Fix initial Reference tag field for 4K PI drives.
mpt3sas: Handle active cable exception event
mpt3sas: Update MPI header to 2.00.42
Revert "lpfc: Delete unnecessary checks before the function call mempool_destroy"
eata_pio: missing break statement
hpsa: Fix type ZBC conditional checks
scsi_lib: Decode T10 vendor IDs
scsi_dh_alua: do not fail for unknown VPD identification
scsi_debug: use locally assigned naa
scsi_debug: uuid for lu name
scsi_debug: vpd and mode page work
scsi_debug: add multiple queue support
bfa: fix bfa_fcb_itnim_alloc() error handling
megaraid_sas: Downgrade two success messages to info
cxlflash: Fix to resolve dead-lock during EEH recovery
scsi_debug: rework resp_report_luns
scsi_debug: use pdt constants
...
The dwc_460ex SATA driver has become available on non-powerpc architectures
and may cause randconfig build errors when CONFIG_DMADEVICES is not set
and SATA_DWC_OLD_DMA is enabled:
warning: (SATA_DWC_OLD_DMA) selects DW_DMAC_CORE which has unmet direct dependencies (DMADEVICES)
ERROR: "dw_dma_probe" [drivers/ata/sata_dwc_460ex.ko] undefined!
ERROR: "dw_dma_remove" [drivers/ata/sata_dwc_460ex.ko] undefined!
This adds an explcit Kconfig dependency to CONFIG_SATA_DWC so we
cannot run into broken configurations. While it would also be
possible to build the driver with both CONFIG_DMADEVICES
and SATA_DWC_OLD_DMA disabled, that case is not useful because
there is no fallback to PIO mode when the DMA engine is not
usable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 50b433753d ("ata: sata_dwc_460ex: use "dmas" DT property to find dma channel")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is a duplication in the debug messages when accessing SCR registers.
Remove duplication to make the messages neat.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
DMA operates with physical addresses which is not exactly the same as ioremap()
returns.
Introduce variable to keep physical address of the SATA FIFO register and
supply it when prepare DMA channel.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This simplifies error handling and cleanup by using devm to manage
IO mappings.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This consolidates the reads from each of the if/else branches
to one place making the code a lot nicer to look at.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Rename the register access macros and use standard _relaxed()
ops instead of __raw variants with explicit byte swapping.
The original driver used the ppc-specific in/out_le32(). When it
was adapted to other systems, these were added to the driver
under ifdefs. However, those names are not defined as macros on
ppc, so it ended up replacing them there as well with altered
semantics. This patch restores the original semantics on ppc and
makes the accesses no less strict on other systems.
Also fixes too many sparse warnings to count.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The pointer to the mmio register base is missing the __iomem
annotation. Fix this.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The (void *__iomem) cast is wrong. Change the target type of the
"base" pointer to void __iomem instead and drop the cast.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Casting a pointer to unsigned long only to immediately cast it back
to a pointer makes no sense. Fix this.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sata_dwc_qc_prep() does nothing. Use the default ata_noop_qc_prep
instead.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here we refactor HOSTDEV{P}_FROM_*() macros to fit one line and fix the
definition of HSDEV_FROM_HSDEVP() where wrong name of the parameter waas used.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This moves all global data into the driver private struct, thus
permitting multiple devices of this type to be used.
The core_scr_read/write() functions are replaced with equivalent
calls to the existing sata_dwc_scr_read/write().
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This adds support for powering on an optional PHY when activating the
device.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently this driver only works with a DesignWare DMA engine which it
registers manually using the second "reg" address range and interrupt
number from the DT node.
This patch makes the driver instead use the "dmas" property if present,
otherwise optionally falling back on the old way so existing device
trees can continue to work.
With this change, there is no longer any reason to depend on the 460EX
machine type so drop that from Kconfig.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_sff_qc_issue() can't handle DMA commands and thus we have to avoid it for
them. Do call ata_bmdma_qc_issue() instead for this case. Note that the former
one distinguishes PIO and DMA mode and behaves accordingly.
Suggested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Calling dmaengine_prep_slave_sg() for non-dma ATA commands is
unnecessary at best and could be harmful if the dma driver reacts
badly to this. It also causes this driver to print a bogus error
message in these cases.
This patch changes sata_dwc_qc_issue() to only do the dma setup
for dma commands and also reports an error to libata if if fails.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is no need to have a platform driver compiled since the DMA driver is
used as a library.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In the original code the DMA is always a flow controller. Set this accordingly
in updated code.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The burst size as defined by DMAengine API is in items of address width. Derive
burst size from AHB_DMA_BRST_DFLT (64 bytes) by dividing it to
DMA_SLAVE_BUSWIDTH_4_BYTES (4 bytes) that gives us 16 items.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The original code states:
Make sure a LLI block is not created that will span 8K max FIS
boundary. If the block spans such a FIS boundary, there is a chance
that a DMA burst will cross that boundary -- this results in an error
in the host controller.
Since we have switched to generic DMAengine API we satisfy above by setting
dma_boundary value to 0x1fff.
Suggested-by: Mans Rullgard <mans@mansr.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes Machine Check "Data Write PLB Error" which happens
when libata-sff's ata_sff_dev_select is trying to write into the
device_addr in order to select a drive. However, SATA has no master
or slave devices like the old ATA Bus, therefore selecting a
different drive is kind of pointless.
Data Write PLB Error
Oops: Machine check, sig: 7 [#1]
PowerPC 44x Platform
Modules linked in:
CPU: 0 PID: 508 Comm: scsi_eh_0 Not tainted 4.6.0-rc3-next-20160412+ #10
[...]
NIP [c027e820] ata_sff_dev_select+0x3c/0x44
LR [c027e810] ata_sff_dev_select+0x2c/0x44
Call Trace:
[cec31cd0] [c027da00] ata_sff_postreset+0x40/0xb4 (unreliable)
[cec31ce0] [c027a03c] ata_eh_reset+0x5cc/0x928
[cec31d60] [c027a840] ata_eh_recover+0x330/0x10bc
[cec31df0] [c027bae0] ata_do_eh+0x4c/0xa4
[...]
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Byte 69 bits 0:1 in the IDENTIFY DEVICE data indicate a
host-aware ZAC device.
Host-managed ZAC devices have their own individual signature,
and to not set the bits in the IDENTIFY DEVICE data.
And whenever we detect a ZAC-compatible device we should
be displaying the zoned block characteristics VPD page.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Device-managed ZAC devices just set the zoned capabilities field
in INQUIRY byte 69 (cf ACS-4). This corresponds to the 'zoned'
field in the block device characteristics VPD page.
As this is only defined in SPC-5/SBC-4 we also need to update
the supported SCSI version descriptor.
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add NCQ encapsulation for ZAC MANAGEMENT OUT and evaluate
NCQ Non-Data log pages to figure out if NCQ encapsulation
is supported.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ZAC drives implement a 'ZAC Management Out' command template,
which maps onto the ZBC OUT command.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
ZAC drives implement a 'ZAC Management In' command template,
which maps onto the ZBC IN command.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
If a device is disabled after error recovery it doesn't make
any sense to generate an ATA sense, but we should rather
return a generic sense code indicating the device is gone.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some commands like FPDMA RECEIVE or NCQ NON DATA can encapsulate
other commands to NCQ transport. So decode the subcmds, too.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When reading the NCQ Send/Recv log it might actually not
supported, thereby causing irritating messages
'READ LOG DMA EXT failed'.
Instead we should be reading the log directory first to
figure out if the log is actually supported before trying
to access it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Do not call ata_request_sense() if the sense code is already
present.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Replace custom approach by %*ph specifier to dump small buffers in hex format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We pass struct dw_dma_chip to dw_dma_probe() anyway, thus we may use it to
pass a platform data as well.
While here, constify the source of the platform data.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.
Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.
Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
AMD Seattle SATA controller mostly conforms to AHCI interface with some
special register to control SGPIO interface. In the case of an AHCI
controller, the SGPIO feature is ideally implemented using the
"Enclosure Management" register of the AHCI controller, but those
registeres are not implemented in the Seattle SoC. Instead SoC
(Rev B0 onwards) provides a 32-bit SGPIO control register which should
be programmed to control the activity, locate and fault LEDs.
The driver is based on ahci_platform driver.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: tj@kernel.org
CC: linux-ide@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fix spelling typos found in Documentation/Docbook/libata.xml.
It is because the file was generated from comments in source,
I had to fix comments in libata-core.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The source and destination masters are reflecting buses or their layers to
where the different devices can be connected. The patch changes the master
names to reflect which one is related to which independently on the transfer
direction.
The outcome of the change is that the memory data width is now always limited
by a data width of the master which is dedicated to communicate to memory.
The patch will not break anything since all current users have the same data
width for all masters. Though it would be nice to revisit avr32 platforms to
check what is the actual hardware topology in use there. It seems that it has
one bus and two masters on it as stated by Table 8-2, that's why everything
works independently on the master in use. The purpose of the sequential patch
is to fix the driver for configuration of more than one bus.
The change is done in the assumption that src_master and dst_master are
reflecting a connection to the memory and peripheral correspondently on avr32
and otherwise on the rest.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When spinning up a drive from powered on standby mode (PUIS),
SETFEATURES_SPINUP is executed with the default timeout used
for any SETFEATURES subcommand, that is 5+10 seconds. The
total 15s is too short for some drives to complete spinup
(e.g. drives with a large indirection table stored on media),
resulting in ata_dev_read_id to fail twice on the execution
of SETFEATURES_SPINUP. For this feature, allow a larger
default timeout of 30 seconds. However, in the same spirit
as with the timeout of other feature subcommands, do not
ignore ata_probe_timeout if it is set).
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Whenever the sense key is set to 'invalid parameter' we should
be filling out the sense-key specific information field in the
sense buffer.
tj: Added description of @fp for ata_mselect_*().
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When generating a sense code of 'Invalid field in CDB' we
should be setting the bit pointer where appropriate.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
If the sense code is 'Invalid field in CDB' we should be
setting the field pointer to the offending byte.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Implement MODE SELECT for the control mode page to allow the OS
to switch to descriptor sense.
tj: Dropped s/sb/cmd->sense_buffer/ in ata_gen_ata_sense(). Added
@dev description to ata_msense_ctl_mode().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Generate ATA pass-through sense for both fixed and descriptor
format sense.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Whenever a sense code is set it would need to be evaluated to
update the error mask.
tj: Cosmetic formatting updates.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use ata_scsi_set_sense() throughout to ensure the sense code
format is consistent.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
If NCQ autosense or the sense data reporting feature is enabled
the LBA of the offending command should be stored in the sense
data 'information' field.
tj: s/(u64)-1/U64_MAX/
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use scsi_set_sense_information() instead of hand-crafted function.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Return U64_MAX if ata_tf_read_block() could not decode the LBA
address, and do not set the information sense descriptor in
ata_gen_ata_sense() in these cases.
tj: s/(u64)-1/U64_MAX/
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_to_sense_error() is called conditionally, so we should be
generating a default sense if the condition is not met.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ACS-4 defines a sense data reporting feature set.
This patch implements support for it.
tj: Cosmetic formatting updates.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some newer devices support NCQ autosense (cf ACS-4), so we should
be using it to retrieve the sense code and speed up recovery.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
On some SOCs PORTS_IMPL register value is never programmed by the
firmware and left at zero value. Which means that no sata ports are
available for software. AHCI driver used to cope up with this by
fabricating the port_map if the PORTS_IMPL register is read zero,
but recent patch broke this workaround as zero value was valid for
NVMe disks.
This patch adds ports-implemented DT bindings as workaround for this issue
in a way that DT can can override the PORTS_IMPL register in cases where
the firmware did not program it already.
Fixes: 566d1827df ("libata: disable forced PORTS_IMPL for >= AHCI 1.3")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
In usecases where force_port_map is used saved_port_map is never set,
resulting in not programming the PORTS_IMPL register as part of initial
config. This patch fixes this by setting it to port_map even in case
where force_port_map is used, making it more inline with other parts of
the code.
Fixes: 566d1827df ("libata: disable forced PORTS_IMPL for >= AHCI 1.3")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
- ahci grew runtime power management support so that the controller can
be turned off if no devices are attached.
- sata_via isn't dead yet. It got hotplug support and more refined
workaround for certain WD drives.
- Misc cleanups. There's a merge from for-4.5-fixes to avoid confusing
conflicts in ahci PCI ID table.
* 'for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: ahci_xgene: dereferencing uninitialized pointer in probe
AHCI: Remove obsolete Intel Lewisburg SATA RAID device IDs
ata: sata_rcar: Use ARCH_RENESAS
sata_via: Implement hotplug for VT6421
sata_via: Apply WD workaround only when needed on VT6421
ahci: Add runtime PM support for the host controller
ahci: Add functions to manage runtime PM of AHCI ports
ahci: Convert driver to use modern PM hooks
ahci: Cache host controller version
scsi: Drop runtime PM usage count after host is added
scsi: Set request queue runtime PM status back to active on resume
block: Add blk_set_runtime_active()
ata: ahci_mvebu: add support for Armada 3700 variant
libata: fix unbalanced spin_lock_irqsave/spin_unlock_irq() in ata_scsi_park_show()
libata: support AHCI on OCTEON platform
Merge second patch-bomb from Andrew Morton:
- a couple of hotfixes
- the rest of MM
- a new timer slack control in procfs
- a couple of procfs fixes
- a few misc things
- some printk tweaks
- lib/ updates, notably to radix-tree.
- add my and Nick Piggin's old userspace radix-tree test harness to
tools/testing/radix-tree/. Matthew said it was a godsend during the
radix-tree work he did.
- a few code-size improvements, switching to __always_inline where gcc
screwed up.
- partially implement character sets in sscanf
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
sscanf: implement basic character sets
lib/bug.c: use common WARN helper
param: convert some "on"/"off" users to strtobool
lib: add "on"/"off" support to kstrtobool
lib: update single-char callers of strtobool()
lib: move strtobool() to kstrtobool()
include/linux/unaligned: force inlining of byteswap operations
include/uapi/linux/byteorder, swab: force inlining of some byteswap operations
include/asm-generic/atomic-long.h: force inlining of some atomic_long operations
usb: common: convert to use match_string() helper
ide: hpt366: convert to use match_string() helper
ata: hpt366: convert to use match_string() helper
power: ab8500: convert to use match_string() helper
power: charger_manager: convert to use match_string() helper
drm/edid: convert to use match_string() helper
pinctrl: convert to use match_string() helper
device property: convert to use match_string() helper
lib/string: introduce match_string() helper
radix-tree tests: add test for radix_tree_iter_next
radix-tree tests: add regression3 test
...
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
The new helper returns index of the mathing string in an array. We
would use it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the call to acpi_get_object_info() fails then "info" hasn't been
initialized. In that situation, we already know that "version" should
be XGENE_AHCI_V1 so we don't actually need to dereference "info".
Fixes: c9802a4be6 ('ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
These PCI device IDs have been removed from the Intel Lewisburg design
specification. They are no longer needed.
Signed-off-by: Scott Lawson <scott.lawson@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
The HPCP bit is set by bioses for on-board sata ports either because
they think sata is hotplug capable in general or to allow Windows
to display a "device eject" icon on ports which are routed to an
external connector bracket.
However in Redhat Bugzilla #1310682, users report that with kernel 4.4,
where this bit test first appeared, a lot of partitions on sata drives
are now mounted automatically.
This patch should fix redhat and a lot of other distros which
unconditionally automount all devices which have the "removable"
bit set.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 8a3e33cf92 ("ata: ahci: find eSATA ports and flag them as removable" changes userspace behavior)
Link: http://lkml.kernel.org/g/56CF35FA.1070500@redhat.com
Cc: stable@vger.kernel.org #v4.4+
Due to Errata in ThunderX, HOST_IRQ_STAT should be
cleared before leaving the interrupt handler.
The patch attempts to satisfy the need.
Changes from V2:
- removed newfile
- code is now under CONFIG_ARM64
Changes from V1:
- Rebased on top of libata/for-4.6
- Moved ThunderX intr handler to new file
tj: Minor adjustments to comments.
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently, workaround for broken WD drives is applied always, slowing
down all drives. And it has a bug - it's not applied after resume.
Apply the workaround only if the error really appears
(SErr == 0x1000500). This allows unaffected drives to run at full speed
(provided that no affected drive is connected to the controller).
Also make sure the workaround is re-applied on resume.
Tested on VT6421.
As SCR registers access is known to cause problems on VT6420 (and I
don't have it to test), keep the workaround applied always on VT6420.
Unaffected drive (Hitachi HDS721680PLA380):
Before:
$ hdparm -t --direct /dev/sdb
/dev/sdb:
Timing O_DIRECT disk reads: 160 MB in 3.01 seconds = 53.16 MB/sec
After:
$ hdparm -t --direct /dev/sdb
/dev/sdb:
Timing O_DIRECT disk reads: 200 MB in 3.01 seconds = 66.47 MB/sec
Affected drive (WDC WD5003ABYX-18WERA0):
Before:
$ hdparm -t --direct /dev/sda
/dev/sda:
Timing O_DIRECT disk reads: 180 MB in 3.02 seconds = 59.51 MB/sec
After:
$ hdparm -t --direct /dev/sdb
/dev/sdb:
Timing O_DIRECT disk reads: 156 MB in 3.03 seconds = 51.48 MB/sec
$ hdparm -t --direct /dev/sdb
/dev/sdb:
Timing O_DIRECT disk reads: 180 MB in 3.02 seconds = 59.64 MB/sec
The first hdparm is slower because of the error:
[ 50.408042] ata5: Incompatible drive: enabling workaround. This slows down transfer rate to ~60 MB/s
[ 50.728052] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 50.744834] ata5.00: configured for UDMA/133
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds runtime PM support for the AHCI host controller driver so
that the host controller is powered down when all SATA ports are runtime
suspended. Powering down the AHCI host controller can reduce power
consumption and possibly allow the CPU to enter lower power idle states
(S0ix) during runtime.
Runtime PM is blocked by default and needs to be unblocked from userspace
as needed (via power/* sysfs nodes).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add new functions ahci_rpm_get_port()/ahci_rpm_put_port() that change
runtime PM status of AHCI ports. Depending if the AHCI host has runtime PM
enabled or disabled calling these may trigger runtime suspend/resume of the
host controller.
We also call these functions in appropriate places to make sure host
controller registers are available before using them.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In order to add support for runtime PM to the ahci driver we first need to
convert the driver to use modern non-legacy system suspend hooks. There
should be no functional changes.
tj: Updated .driver.pm init for older compilers as suggested by Andy
and Chrsitoph.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This allows sysfs nodes to read the cached value directly instead of
powering up possibly runtime suspended controller.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The main difference in the new Armada 3700 is that no address
decoding needs to take place in the driver probe.
[gregory.clement@free-electrons.com: reformulate the commit log]
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Tested-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_scsi_park_show() was pairing spin_lock_irqsave() with
spin_unlock_irq(). As the function is always called with irq enabled,
it didn't actually break anything. Use spin_lock_irq() instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Elias Oltmanns <eo@nebensachen.de>
This patch complements the list of device IDs previously
added for lewisburg sata.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
The RB532 platform specific irq_to_gpio() implementation has been
removed with commit 832f5dacfa ("MIPS: Remove all the uses of
custom gpio.h"). Now the platform uses the generic stub which causes
the following error:
pata-rb532-cf pata-rb532-cf: no GPIO found for irq149
pata-rb532-cf: probe of pata-rb532-cf failed with error -2
Drop the irq_to_gpio() call and get the GPIO number from platform
data instead. After this change, the driver works again:
scsi host0: pata-rb532-cf
ata1: PATA max PIO4 irq 149
ata1.00: CFA: CF 1GB, 20080820, max MWDMA4
ata1.00: 1989792 sectors, multi 0: LBA
ata1.00: configured for PIO4
scsi 0:0:0:0: Direct-Access ATA CF 1GB 0820 PQ: 0\
ANSI: 5
sd 0:0:0:0: [sda] 1989792 512-byte logical blocks: (1.01 GB/971 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't\
support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
Fixes: 832f5dacfa ("MIPS: Remove all the uses of custom gpio.h")
Cc: Alban Bedel <albeu@free.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org> #v4.3+
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Most arches have an asm/gpio.h that merely includes linux/gpio.h. The
others select ARCH_HAVE_CUSTOM_GPIO_H, and when that's selected,
linux/gpio.h includes asm/gpio.h.
Therefore, code should include linux/gpio.h instead of including asm/gpio.h
directly.
Remove includes of asm/gpio.h, adding an include of linux/gpio.h when
necessary.
This is a follow-on to 7563bbf89d ("gpiolib/arches: Centralise
bolierplate asm/gpio.h").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The OCTEON SATA controller is currently found on cn71XX devices.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Vinita Gupta <vgupta@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As reported by Soohoon Lee, the HDIO_GET_32BIT ioctl does not
work correctly in compat mode with libata.
I have investigated the issue further and found multiple problems
that all appeared with the same commit that originally introduced
HDIO_GET_32BIT handling in libata back in linux-2.6.8 and presumably
also linux-2.4, as the code uses "copy_to_user(arg, &val, 1)" to copy
a 'long' variable containing either 0 or 1 to user space.
The problems with this are:
* On big-endian machines, this will always write a zero because it
stores the wrong byte into user space.
* In compat mode, the upper three bytes of the variable are updated
by the compat_hdio_ioctl() function, but they now contain
uninitialized stack data.
* The hdparm tool calling this ioctl uses a 'static long' variable
to store the result. This means at least the upper bytes are
initialized to zero, but calling another ioctl like HDIO_GET_MULTCOUNT
would fill them with data that remains stale when the low byte
is overwritten. Fortunately libata doesn't implement any of the
affected ioctl commands, so this would only happen when we query
both an IDE and an ATA device in the same command such as
"hdparm -N -c /dev/hda /dev/sda"
* The libata code for unknown reasons started using ATA_IOC_GET_IO32
and ATA_IOC_SET_IO32 as aliases for HDIO_GET_32BIT and HDIO_SET_32BIT,
while the ioctl commands that were added later use the normal
HDIO_* names. This is harmless but rather confusing.
This addresses all four issues by changing the code to use put_user()
on an 'unsigned long' variable in HDIO_GET_32BIT, like the IDE subsystem
does, and by clarifying the names of the ioctl commands.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Soohoon Lee <Soohoon.Lee@f5.com>
Tested-by: Soohoon Lee <Soohoon.Lee@f5.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Due to H/W errata, the HOST_IRQ_STAT register misses the edge interrupt
when clearing the HOST_IRQ_STAT register and hardware reporting the
PORT_IRQ_STAT register happens to be at the same clock cycle.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The flexibility to override the irq handles in the LLD's are already
present, so controllers implementing a edge trigger latch can
implement their own interrupt handler inside the driver. This patch
removes the AHCI_HFLAG_EDGE_IRQ support from libahci and moves edge
irq handling to ahci_xgene.
tj: Minor update to description.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kenrel.org>
This patch implements the capability to override the generic AHCI
interrupt handler so that specific ahci drivers can implement their
own custom interrupt handler routines. It also exports
ahci_handle_port_intr so that custom irq_handler implementations can
use it.
tj: s/ahci_irq_handler/irq_handler/ and updated description.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Drivers should include asm/pci-bridge.h only when they need the arch-
specific things provided there. Outside of the arch/ directories, the only
drivers that actually need things provided by asm/pci-bridge.h are the
powerpc RPA hotplug drivers in drivers/pci/hotplug/rpa*.
Remove the includes of asm/pci-bridge.h from the other drivers, adding an
include of linux/pci.h if necessary.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The bulk of ATA host state machine is implemented by
ata_sff_hsm_move(). The function is called from either the interrupt
handler or, if polling, a work item. Unlike from the interrupt path,
the polling path calls the function without holding the host lock and
ata_sff_hsm_move() selectively grabs the lock.
This is completely broken. If an IRQ triggers while polling is in
progress, the two can easily race and end up accessing the hardware
and updating state machine state at the same time. This can put the
state machine in an illegal state and lead to a crash like the
following.
kernel BUG at drivers/ata/libata-sff.c:1302!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN
Modules linked in:
CPU: 1 PID: 10679 Comm: syz-executor Not tainted 4.5.0-rc1+ #300
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff88002bd00000 ti: ffff88002e048000 task.ti: ffff88002e048000
RIP: 0010:[<ffffffff83a83409>] [<ffffffff83a83409>] ata_sff_hsm_move+0x619/0x1c60
...
Call Trace:
<IRQ>
[<ffffffff83a84c31>] __ata_sff_port_intr+0x1e1/0x3a0 drivers/ata/libata-sff.c:1584
[<ffffffff83a85611>] ata_bmdma_port_intr+0x71/0x400 drivers/ata/libata-sff.c:2877
[< inline >] __ata_sff_interrupt drivers/ata/libata-sff.c:1629
[<ffffffff83a85bf3>] ata_bmdma_interrupt+0x253/0x580 drivers/ata/libata-sff.c:2902
[<ffffffff81479f98>] handle_irq_event_percpu+0x108/0x7e0 kernel/irq/handle.c:157
[<ffffffff8147a717>] handle_irq_event+0xa7/0x140 kernel/irq/handle.c:205
[<ffffffff81484573>] handle_edge_irq+0x1e3/0x8d0 kernel/irq/chip.c:623
[< inline >] generic_handle_irq_desc include/linux/irqdesc.h:146
[<ffffffff811a92bc>] handle_irq+0x10c/0x2a0 arch/x86/kernel/irq_64.c:78
[<ffffffff811a7e4d>] do_IRQ+0x7d/0x1a0 arch/x86/kernel/irq.c:240
[<ffffffff86653d4c>] common_interrupt+0x8c/0x8c arch/x86/entry/entry_64.S:520
<EOI>
[< inline >] rcu_lock_acquire include/linux/rcupdate.h:490
[< inline >] rcu_read_lock include/linux/rcupdate.h:874
[<ffffffff8164b4a1>] filemap_map_pages+0x131/0xba0 mm/filemap.c:2145
[< inline >] do_fault_around mm/memory.c:2943
[< inline >] do_read_fault mm/memory.c:2962
[< inline >] do_fault mm/memory.c:3133
[< inline >] handle_pte_fault mm/memory.c:3308
[< inline >] __handle_mm_fault mm/memory.c:3418
[<ffffffff816efb16>] handle_mm_fault+0x2516/0x49a0 mm/memory.c:3447
[<ffffffff8127dc16>] __do_page_fault+0x376/0x960 arch/x86/mm/fault.c:1238
[<ffffffff8127e358>] trace_do_page_fault+0xe8/0x420 arch/x86/mm/fault.c:1331
[<ffffffff8126f514>] do_async_page_fault+0x14/0xd0 arch/x86/kernel/kvm.c:264
[<ffffffff86655578>] async_page_fault+0x28/0x30 arch/x86/entry/entry_64.S:986
Fix it by ensuring that the polling path is holding the host lock
before entering ata_sff_hsm_move() so that all hardware accesses and
state updates are performed under the host lock.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
Link: http://lkml.kernel.org/g/CACT4Y+b_JsOxJu2EZyEf+mOXORc_zid5V1-pLZSroJVxyWdSpw@mail.gmail.com
Cc: stable@vger.kernel.org
ata_sff_hsm_move() triggers BUG if it sees a host state machine state
that it dind't expect. The risk for data corruption when the
condition occurs is low as it's highly unlikely that it would lead to
spurious completion of commands. The BUG occasionally triggered for
subtle race conditions in the driver. Let's downgrade it to WARN so
that it doesn't kill the machine unnecessarily.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Some early controllers incorrectly reported zero ports in PORTS_IMPL
register and the ahci driver fabricates PORTS_IMPL from the number of
ports in those cases. This hasn't mattered but with the new nvme
controllers there are cases where zero PORTS_IMPL is valid and should
be honored.
Disable the workaround for >= AHCI 1.3.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/g/CALCETrU7yMvXEDhjAUShoHEhDwifJGapdw--BKxsP0jmjKGmRw@mail.gmail.com
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org
The AHCI driver code stops and starts port DMA engines at will
without considering the power state of the particular port. The
AHCI specification isn't very clear on how to handle this scenario,
leaving implementation open to interpretation.
Broadcom's STB SATA host controller is unable to handle port DMA
controller restarts when the port in question is in low power mode.
When a port enters partial or slumber mode, its PHY is powered down.
When a controller restart is requested, the controller's internal
state machine expects the PHY to be brought back up by software which
never happens in this case, resulting in failures.
To avoid this situation, logic is added to manually wake up the port
just before its DMA engine is stopped, if the port happens to be in
a low power state. HBA initiated power management ensures that the port
eventually returns to its configured low power state, when the link is
idle (as per the conditions listed in the spec). A new host flag is also
added to ensure this logic is only exercised for hosts with the above
limitation.
tj: Formatting changes.
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Mostly low level driver specific changes.
Two changes are somewhat noteworthy. First, Dan's patchset to support
per-port msix interrupt handling for ahci, which was tried last cycle
but had to be backed out due to a couple issues, is back and seems to
be working fine. Second, libata exception handling now uses
usleep_range() instead of msleep() for sleeps < 20ms which can make
things snappier in some corner cases"
* 'for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: skip debounce delay on link resume
ata: ahci_brcmstb: disable DIPM support
ata: ahci_brcmstb: enable support for ALPM
drivers: libata-core: Use usleep_range() instead of msleep() for short sleeps (<20 ms)
sata_sx4: correctly handling failed allocation
ata: ahci_brcmstb: add support for MIPS-based platforms
ahci: qoriq: Adjust the default register values on ls1021a
ahci: qoriq: Update the default Rx watermark value
ahci: qoriq: Adjust the default register values on ls1043a
ahci: compile out msi/msix infrastructure
ata: core: fix irq description on AHCI single irq systems
ata: ahci_brcmstb: remove unused definitions
ata: ahci_brcmstb: add a quirk for MIPS-based platforms
ata: ahci_brcmstb: disable NCQ for MIPS-based platforms
ata: sata_rcar: Remove obsolete platform_device_id entries
sata_rcar: Add compatible string for r8a7795
ahci: kill 'intr_status'
ahci: switch from 'threaded' to 'hardirq' interrupt handling
ahci: per-port msix support
The link resume logic uses a 200msec delay while debouncing
the SControl register. The rationale behind that delay is
to accommodate some PHYs that behave badly if their SStatus/
SControl registers are pounded immediately on resume.
The Broadcom STB SATA PHY does not seem to have this issue.
This patch introduces a new link flag that allows platforms
to skip the debounce delay if it isn't needed.
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Broadcom STB SATA host controller does not support device
initiated power management. Disable support for this feature
so the driver never sends SETFEATURES commands to the device
to enable/disable DIPM.
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Enable support for ALPM in the host controller's capabilities
register. Also adjust the PLL timeout to give it enough time
to lock when the port exits slumber mode.
tj: minor style updates
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since msleep() may sleep longer than intended time for values less
than 20ms, this patch allows the use of usleep_range for waits less
that 20ms. usleep_range is a finer precision implementation of
msleep and is designed to be a drop-in replacement for udelay
where a precise sleep/busy-wait is unnecessary.
More details can be found at http://lkml.org/lkml/2007/8/3/250
and in Documentation/timers/timers-howto.txt.
This change has been done to improve the performace in PIO6 mode
which is used by viking flash.
Cc: xe-kernel@external.cisco.com
Signed-off-by: Anil Veliyankara Madam <aveliyan@cisco.com>
Signed-off-by: Shikha Jain <shikjain@cisco.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since kzalloc can be failed in memory pressure, return error when failed.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The BCM7xxx ARM-based and MIPS-based platforms share a similar hardware
block for AHCI SATA3.
This new compatible string, "brcm,bcm7425-ahci", may be used for most
MIPS-based platforms of 40nm process technology.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Updated the registers' values to enhance SATA performance and
reliability on ls1021a soc.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The PTC[RXWM] sets the watermark value for Rx FIFO. The default
value 0x20 might be insufficient for some hard drives. If the
watermark value is too small, a single-cycle overflow may occur
and is reported as a CRC or internal error in the PxSERR register.
Updated the value to 0x29 according to the validation test.
All LS platforms are affected.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Updated the registers' values to enhance SATA performance and
reliability.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Every attempt to issue a read log page command lockup the controller.
The command is currently sent if the sata device includes the devlsp feature
to read out the timing data.
This attempt to read the data, locks up the controller and the device
is not recognzied correctly (failed to set xfermode) and cannot be accessed.
This was found on Freescale P1013/P1022 and T4240 CPUs
using a ATP IG mSATA 4GB with the devslp feature.
fsl-sata ff718000.sata: Sata FSL Platform/CSB Driver init
[ 1.254195] scsi0 : sata_fsl
[ 1.256004] ata1: SATA max UDMA/133 irq 74
[ 1.370666] fsl-gianfar ethernet.3: enabled errata workarounds, flags: 0x4
[ 1.470671] fsl-gianfar ethernet.4: enabled errata workarounds, flags: 0x4
[ 1.775584] ata1: Signature Update detected @ 504 msecs
[ 1.947594] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.948366] ata1.00: ATA-8: ATP IG mSATA, 20150311, max UDMA/133
[ 1.948371] ata1.00: 7732368 sectors, multi 0: LBA
[ 1.948843] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 1.948857] ata1.00: failed to set xfermode (err_mask=0x40)
[ 7.467557] ata1: Signature Update detected @ 504 msecs
[ 7.639560] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 7.651320] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 7.651360] ata1.00: failed to set xfermode (err_mask=0x40)
[ 7.655628] ata1: limiting SATA link speed to 1.5 Gbps
[ 7.659458] ata1.00: limiting speed to UDMA/133:PIO3
[ 13.163554] ata1: Signature Update detected @ 504 msecs
[ 13.335558] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 13.347298] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 13.347334] ata1.00: failed to set xfermode (err_mask=0x40)
[ 13.351601] ata1.00: disabled
[ 13.353278] ata1: exception Emask 0x50 SAct 0x0 SErr 0x800 action 0x6 frozen t4
[ 13.359281] ata1: SError: { HostInt }
[ 13.361644] ata1: hard resetting link
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some controller lockup on a ata_read_log_page.
Add new ata port flag ATA_FLAG_NO_LOG_PAGE which can used
to blacklist a controller.
If this flag is set, any attempt to read a log page returns an error
without actually issuing the command.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Quoting Arnd:
The AHCI driver is used for some on-chip devices that do not use PCI
for probing, and it can be built even when CONFIG_PCI is disabled, but
that now results in a build failure:
ata/libahci.c: In function 'ahci_host_activate_multi_irqs':
ata/libahci.c:2475:4: error: invalid use of undefined type 'struct msix_entry'
ata/libahci.c:2475:21: error: dereferencing pointer to incomplete type 'struct msix_entry'
Add ifdef CONFIG_PCI_MSI infrastructure to compile out the multi-msi and
multi-msix code.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested--by: Arnd Bergmann <arnd@arndb.de>
[arnd: fix up pci enabled case]
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fixes: d684a90d38 ("ahci: per-port msix support")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
On my machine with single irq AHCI just the PCI id is printed as
description in /proc/interrupts.
I found a related discussion from beginning of this year:
http://www.gossamer-threads.com/lists/linux/kernel/2117335
Seems like 4f37b50476 ("libata: Use dev_name() for request_irq() to
distinguish devices") tried to fix displaying a proper interrupt
description for one scenario but broke it for another one.
The mentioned discussion ended in the current situation being
considered as broken but w/o a patch to fix it.
The following patch is based on a proposal in this mail thread.
Now the interrupt is properly described as:
PCI-MSI 512000-edge ahci[0000:00:1f.2]
By combining both values also the scenario that commit 4f37b50476
("libata: Use dev_name() for request_irq() to distinguish devices")
refers to should still be fine. There it should look like this now:
ahci[20100000.ide]
Using managed memory allocation ensures that the irq description
lives at least as long as the interrupt.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
When I connect an Intel SSD to SATA SIL controller (PCI ID 1095:3114), any
TRIM command results in I/O errors being reported in the log. There is
other similar error reported with TRIM and the SIL controller:
https://bugs.centos.org/view.php?id=5880
Apparently the controller doesn't support TRIM commands. This patch
disables TRIM support on the SATA SIL controller.
ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata7.00: BMDMA2 stat 0x50001
ata7.00: failed command: DATA SET MANAGEMENT
ata7.00: cmd 06/01:01:00:00:00/00:00:00:00:00/a0 tag 0 dma 512 out
res 51/04:01:00:00:00/00:00:00:00:00/a0 Emask 0x1 (device error)
ata7.00: status: { DRDY ERR }
ata7.00: error: { ABRT }
ata7.00: device reported invalid CHS sector 0
sd 8:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 8:0:0:0: [sdb] tag#0 Sense Key : Illegal Request [current] [descriptor]
sd 8:0:0:0: [sdb] tag#0 Add. Sense: Unaligned write command
sd 8:0:0:0: [sdb] tag#0 CDB: Write same(16) 93 08 00 00 00 00 00 21 95 88 00 20 00 00 00 00
blk_update_request: I/O error, dev sdb, sector 2200968
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Current code doesn't update port value of Port Multiplier(PM) when
sending FIS of softreset to device, command will fail if FBS is
enabled.
There are two ways to fix the issue: the first is to disable FBS
before sending softreset command to PM device and the second is
to update port value of PM when sending command.
For the first way, i can't find any related rule in AHCI Spec. The
second way can avoid disabling FBS and has better performance.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Remove unused definitions, and this is to avoid confusion with MIPS-based
platforms.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Whereas ARM-based platforms have four phy interface registers and
information, the MIPS-based platforms have only three registers, and
there are no information and documentation. In the original BSP, It
using "strict-ahci" did not control these registers.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
The most MIPS-based platforms need to disable NCQ while have the NCQ
capability in HOST_CAP, and several ARM-based platforms (eg. BCM7349A0,
BCM7445A0, BCM7445B0) need to disable too.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Since commit c99cd90d98 ("ARM: shmobile: r8a7779: Remove legacy
SoC code"), R-Car SoCs are only supported in generic DT-only ARM
multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the remaining platform_device_id
entries and platform device support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
The newly added suspend/resume implementation for ahci_mvebu causes
a link error when CONFIG_PM_SLEEP is disabled:
ERROR: "ahci_platform_suspend_host" [drivers/ata/ahci_mvebu.ko] undefined!
ERROR: "ahci_platform_resume_host" [drivers/ata/ahci_mvebu.ko] undefined!
This adds the same #ifdef here that exists in the ahci_platform driver
which defines the above functions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d6ecf15814 ("ata: ahci_mvebu: add suspend/resume support")
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This field in achi_port_priv was only used to support threaded
interrupts. Now that we are hardirq only it can be deleted.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For high frequency I/O the overhead of threaded interrupts impacts
performance. A quick out-of-the-box test (i.e. no affinity tuning)
shows ~10% random read performance at ~20% less cpu. The cpu wins
appear to be from reduced lock contention.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some AHCI controllers support per-port MSI-X vectors. At the same time
the Linux AHCI driver needs to support one-off architectures that
implement a single MSI-X vector for all ports. The heuristic for
enabling AHCI ports becomes, in order of preference:
1/ per-port multi-MSI-X
2/ per-port multi-MSI
3/ single MSI
4/ single MSI-X
5/ legacy INTX
This all depends on AHCI implementations with potentially broken MSI-X
requesting less vectors than the number of ports. If this assumption is
violated we will need to start explicitly white-listing AHCI-MSIX
implementations.
Reported-by: Ricardo Neri <ricardo.neri@intel.com>
[ricardo: fix struct msix_entry handling]
Reported-by: kernel test robot <ying.huang@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This change was to preserve the ascending order of device IDs.
There was an exception with the first two Lewisburg device IDs to
keep all device IDs of the same kind grouped by code name.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds missing AHCI RAID SATA Device IDs for the Intel Sunrise
Point PCH.
Signed-off-by: Nanda Kishore Chinna <nanda_kishore_chinna@dell.com>
Signed-off-by: Charles Rose <charles_rose@dell.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Sorry for the delay in this patch which was mostly caused by getting the
merger of the mpt2/mpt3sas driver, which was seen as an essential item of
maintenance work to do before the drivers diverge too much. Unfortunately,
this caused a compile failure (detected by linux-next), which then had to be
fixed up and incubated. In addition to the mpt2/3sas rework, there are
updates from pm80xx, lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc
and ufs plus an assortment of changes including some year 2038 issues, a fix
for a remove before detach issue in some drivers and a couple of other minor
issues.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJWRnpiAAoJEDeqqVYsXL0MJd0IAIkNP1q/6ksMw/lam2UlbdxN
zFsFOIhGM3xLnBFehbCx7JW3cmybA7WC5jhMjaa1OeJmYHLpwbTzvVwrLs2l/0y1
/S+G0wwxROZfIKj/1EO3oKbSPCu9N3lStxOnmNXt5PSUEzAXrTqSNTtnMf2ZGh7j
bQxTWEJe+66GckgGw4ozTXJHWXqM/Zs/FsYjn2h/WzFhFv8utr7zRSzHMVjcqpLG
TK/Lt03hiTGqiignKrV9W6JzdGTWf2LGIsj/njgR0dxv59cNH8PrHIjZyknSBxgn
lblinsCjxDHWnP4BSfTi9MQG1lEiZiWO3Y6TKkKJTgxZ9M0Eitspc+cLOiJ1mpg=
=HvQf
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"Sorry for the delay in this patch which was mostly caused by getting
the merger of the mpt2/mpt3sas driver, which was seen as an essential
item of maintenance work to do before the drivers diverge too much.
Unfortunately, this caused a compile failure (detected by linux-next),
which then had to be fixed up and incubated.
In addition to the mpt2/3sas rework, there are updates from pm80xx,
lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus
an assortment of changes including some year 2038 issues, a fix for a
remove before detach issue in some drivers and a couple of other minor
issues"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
mpt3sas: fix inline markers on non inline function declarations
sd: Clear PS bit before Mode Select.
ibmvscsi: set max_lun to 32
ibmvscsi: display default value for max_id, max_lun and max_channel.
mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl()
scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()
mvumi: 64bit value for seconds_since1970
be2iscsi: Fix bogus WARN_ON length check
scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice
mpt3sas: Bump mpt3sas driver version to 09.102.00.00
mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs
mpt2sas, mpt3sas: Update the driver versions
mpt3sas: setpci reset kernel oops fix
mpt3sas: Added OEM Gen2 PnP ID branding names
mpt3sas: Refcount fw_events and fix unsafe list usage
mpt3sas: Refcount sas_device objects and fix unsafe list usage
mpt3sas: sysfs attribute to report Backup Rail Monitor Status
mpt3sas: Ported WarpDrive product SSS6200 support
mpt3sas: fix for driver fails EEH, recovery from injected pci bus error
mpt3sas: Manage MSI-X vectors according to HBA device type
...
This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags. We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
With devm there is no need to explicitly free irqs on error.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
MSI messages are per-device, so there will never be another "shared"
device in the interrupt chain.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
NCQ feature can't be used due to the erratum A-008473.
This patch disables NCQ as a workaround.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Freescale is renaming the LS2085A SoC to LS2080A.
This patch addresses the same.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch is needed to make NCQ commands with FPDMA protocol value
(eg READ/WRITE FPDMA) work over SCSI Generic (SG) interface.
Signed-off-by: Vinayak Kale <vinayak.kale@seagate.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
kbuild test robot reports the warnings:
drivers/ata/ahci_qoriq.c: In function 'ahci_qoriq_hardreset':
>> include/asm-generic/io.h:163:2: warning: 'px_is' may be used
>> uninitialized in this function [-Wuninitialized]
drivers/ata/ahci_qoriq.c:70:14: note: 'px_is' was declared here
>> include/asm-generic/io.h:163:2: warning: 'px_cmd' may be used
>> uninitialized in this function [-Wuninitialized]
drivers/ata/ahci_qoriq.c:70:6: note: 'px_cmd' was declared here
This patch fixed it by introducing a local variable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some string literals are pointed to by "char *". This patch fixes
that.
tj: Updated patch title and description.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When calling ->done before releasing resources we could run into a
race where the SCSI midlayer sends another command and races with
the resources beeing manipulated. For libata this can't currently
happen as synchronization happens at a higher level, but I'd still
like to fix it to future proof libata and to avoid copy & paste
into SCSI drivers where this pattern has led to reproducible crashes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Remove an incorrect comment and untangle an if statement in
ata_scsi_qc_complete.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
If the AHCI ports' HPCP or ESP bits are set, the port
should be considered external (e.g. eSATA) and is marked
as removable. Userspace tools like udisks then treat it
like an usb drive.
With this patch applied, when I plug a drive into the esata port,
KDE pops up a window asking what to do with the drives(s), just
like it does for any random USB stick.
Removability is indicated to the upper layers by way of the
SCSI RMB bit, as I haven't found another way to signal
userspace to treat a sata disk like any usb stick.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
This patch adds the missing MODULE_DEVICE_TABLE() for OF to export
that information so modules have the correct aliases built-in and
autoloading works correctly.
Link: https://lkml.org/lkml/2015/7/30/519
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The PXA architecture was offered a slave dmaengine support. As a
consequence the direct DMA registers are progressively replaced by
dmaengine support.
This makes the pata_pxa change, which brings this driver to almost a
generic ATA 40-wires driver relying on dmaengine for transfers.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently Freescale QorIQ series SATA is supported by ahci_platform
driver. Some SoC specific settings have been put in uboot. So whether
SATA works or not heavily depends on uboot.
This patch will add a new driver to support QorIQ sata which removes
the dependency on any other boot loader.
Freescale QorIQ series sata, like ls1021a ls2085a ls1043a, is
compatible with serial ATA 3.0 and AHCI 1.3 specification.
Signed-off-by: Yuantian Tang <Yuantian.Tang@freescale.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit 5163fb6254
("ahci: added support for Freescale AHCI sata")
The reverted patch added Freescale QorIQ AHCI sata support to
ahci_platform driver though, but it left SoC specific settings to uboot.
It leads to QorIQ sata heavily depending on uboot. In order to removing
the dependency we first revert the old patch and then will add a new driver
for QorIQ SATA.
Since there are no LS* platforms that have been upstreamed, So
the revert would not break anything exists.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS
machines, and each machine type provides its own gpio.h. However
only a handful really implement the GPIO API, most just forward
everythings to gpiolib.
The Alchemy machine is notable as it provides a system to allow
implementing the GPIO API at the board level. But it is not used by
any board currently supported, so it can also be removed.
For most machine types we can just remove the custom gpio.h, as well
as the custom wrappers if some exists. Some of the code found in
the wrappers must be moved to the respective GPIO driver.
A few more fixes are need in some drivers as they rely on linux/gpio.h
to provides some machine specific definitions, or used asm/gpio.h
instead of linux/gpio.h for the gpio API.
Signed-off-by: Alban Bedel <albeu@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Walter <dwalter@google.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Buesch <m@bues.ch>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10828/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull libata updates from Tejun Heo:
"Nothing interesting. A couple device specific minor updates and a
kernel doc change"
* 'for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: pata_arasam_cf: Use devm_clk_get
libata: fix libata-core.c kernel-doc warning
ata: sata_rcar: Remove obsolete sata-r8a779* platform_device_id entries
The Crucial M500 is known to have issues with queued TRIM commands, the
factory recertified SSDs use a different model number naming convention
which causes them to get ignored by the blacklist.
The new naming convention boils down to: s/Crucial_/FC/
Signed-off-by: Guillermo A. Amaral <g@maral.me>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
On multi-function JMicron SATA/PATA/AHCI devices, the PATA controller at
function 1 doesn't work if it is powered on before the SATA controller at
function 0. The result is that PATA doesn't work after resume, and we
print messages like this:
pata_jmicron 0000:02:00.1: Refused to change power state, currently in D3
irq 17: nobody cared (try booting with the "irqpoll" option)
Async resume was introduced in v3.15 by 76569faa62 ("PM / sleep:
Asynchronous threads for resume_noirq"). Prior to that, we powered on
the functions in order, so this problem shouldn't happen.
e6b7e41cdd ("ata: Disabling the async PM for JMicron chip 363/361")
solved the problem for JMicron 361 and 363 devices. With async suspend
disabled, we always power on function 0 before function 1.
Barto then reported the same problem with a JMicron 368 (see comment #57 in
the bugzilla).
Rather than extending the blacklist piecemeal, disable async suspend for
all JMicron multi-function SATA/PATA/AHCI devices.
This quirk could stay in the ahci and pata_jmicron drivers, but it's likely
the problem will occur even if pata_jmicron isn't loaded until after the
suspend/resume. Making it a PCI quirk ensures that we'll preserve the
power-on order even if the drivers aren't loaded.
[bhelgaas: changelog, limit to multi-function, limit to IDE/ATA]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81551
Reported-and-tested-by: Barto <mister.freeman@laposte.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.15+
This patch introduces the use of managed resource function
devm_clk_get instead of clk_get and removes corresponding call
to clk_put in the remove function.
To be compatible with the change various gotos are replaced with
direct returns, and unneeded label is dropped.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Three minor device-specific fixes and revert of NCQ autosense added
during this -rc1.
It turned out that NCQ autosense as currently implemented interferes
with the usual error handling behavior. It will be revisited in the
near future"
* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: ahci_brcmstb: Fix misuse of IS_ENABLED
sata_sx4: Check return code from pdc20621_i2c_read()
Revert "libata: Implement NCQ autosense"
Revert "libata: Implement support for sense data reporting"
Revert "libata-eh: Set 'information' field for autosense"
ata: ahci_brcmstb: Fix warnings with CONFIG_PM_SLEEP=n
Fix kernel-doc warning in libata-core.c:
Warning(..//drivers/ata/libata-core.c:4763): No description found for parameter 'tag'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler.
Switch to use CONFIG_CPU_BIG_ENDIAN instead of __BIG_ENDIAN.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
The variable spd0 might be used uninitialized when pdc20621_i2c_read()
fails. This also generates a compilation warning with gcc 5.1.
tj: use pr_err()
Signed-off-by: Tomer Barletz <barletz@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit 42b966fbf3.
As implemented, ACS-4 sense reporting for ATA devices bypasses error
diagnosis and handling in libata degrading EH behavior significantly.
Revert the related changes for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org #v4.1+
This reverts commit fe7173c206.
As implemented, ACS-4 sense reporting for ATA devices bypasses error
diagnosis and handling in libata degrading EH behavior significantly.
Revert the related changes for now.
ATA_ID_COMMAND_SET_3/4 constants are not reverted as they're used by
later changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org #v4.1+
This reverts commit a1524f226a.
As implemented, ACS-4 sense reporting for ATA devices bypasses error
diagnosis and handling in libata degrading EH behavior significantly.
Revert the related changes for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org #v4.1+
When CONFIG_PM_SLEEP is disabled, brcm_ahci_{suspend,resume} are not
used, which causes such a build warning to occur:
CC drivers/ata/ahci_brcmstb.o
drivers/ata/ahci_brcmstb.c:212:12: warning: 'brcm_ahci_suspend' defined
but not used [-Wunused-function]
static int brcm_ahci_suspend(struct device *dev)
^
drivers/ata/ahci_brcmstb.c:224:12: warning: 'brcm_ahci_resume' defined
but not used [-Wunused-function]
static int brcm_ahci_resume(struct device *dev)
^
LD drivers/ata/built-in.o
Fixes: 766a2d9796 ("ata: add Broadcom AHCI SATA3 driver for STB chips")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"A couple important fixes.
- A block layer change which removed restriction on max transfer size
led to silent data corruption on some devices. A new quirk is
added to restore the old size limit for the reported device. If it
gets reported on more devices, we might have to consider restoring
the restriction for ATA devices by default.
- There finally is a SSD which is confirmed to cause data corruption
on TRIM regardless of which flavor is used. A new quirk is added
and the device is blacklisted
- Other device-specific workarounds"
* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Do not blacklist M510DC
libata: increase the timeout when setting transfer mode
libata: add ATA_HORKAGE_MAX_SEC_1024 to revert back to previous max_sectors limit
libata: force disable trim for SuperSSpeed S238
libata: add ATA_HORKAGE_NOTRIM
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for HP 250GB SATA disk VB0250EAVER
ata: pmp: add quirk for Marvell 4140 SATA PMP
Switch to my kernel.org alias instead of a badly named gmail address,
which I rarely use.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A new Micron drive was just announced, once again recycling the first
part of the model string. Add an underscore to the M510/M550 pattern to
avoid picking up the new DC drive.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
I have a ST4000DM000 disk. If Linux is booted while the disk is spun down,
the command that sets transfer mode causes the disk to spin up. The
spin-up takes longer than the default 5s timeout, so the command fails and
timeout is reported.
Fix this by increasing the timeout to 15s, which is enough for the disk to
spin up.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Since no longer limiting max_sectors to BLK_DEF_MAX_SECTORS (commit 34b48db66e),
data corruption may occur on ST380013AS drive configured on 82801JI (ICH10 Family)
SATA controller. This patch will allow the driver to limit max_sectors as before
# cat /sys/block/sdb/queue/max_sectors_kb
512
I was able to double the max_sectors_kb value up to 16384 on linux-4.2.0-rc2
before seeing corruption, but seems safer to use previous limit. Without this
patch max_sectors_kb will be 32767.
tj: Minor comment update.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # v3.19 and later
Fixes: 34b48db66e ("block: remove artifical max_hw_sectors cap")
This device loses blocks, often the partition table area, on trim.
Disable TRIM.
http://pcengines.ch/msata16a.htm
Signed-off-by: Arne Fitzenreiter <arne_f@ipfire.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Some devices lose data on TRIM whether queued or not. This patch adds
a horkage to disable TRIM.
tj: Collapsed unnecessary if() nesting.
Signed-off-by: Arne Fitzenreiter <arne_f@ipfire.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Enabling AA on HP 250GB SATA disk VB0250EAVER causes errors:
[ 3.788362] ata3.00: failed to enable AA (error_mask=0x1)
[ 3.789243] ata3.00: failed to enable AA (error_mask=0x1)
Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk.
tj: Collected FPDMA_AA entries and updated comment.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This commit adds the necessary quirk to make the Marvell 4140 SATA PMP
work properly. This PMP doesn't like SRST on port number 4 (the host
port) so this commit marks this port as not supporting SRST.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Since commit a483dcbfa2 ("ARM: shmobile: lager: Remove legacy
board support"), R-Car Gen2 SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds ACPI supports for AHCI platform driver, which uses _CLS
method to match the device.
The following is an example of ASL structure in DSDT for a SATA controller,
which contains _CLS package to be matched by the ahci_platform driver:
Device (AHC0) // AHCI Controller
{
Name(_HID, "AMDI0600")
Name (_CCA, 1)
Name (_CLS, Package (3)
{
0x01, // Base Class: Mass Storage
0x06, // Sub-Class: serial ATA
0x01, // Interface: AHCI
})
Name (_CRS, ResourceTemplate ()
{
Memory32Fixed (ReadWrite, 0xE0300000, 0x00010000)
Interrupt (ResourceConsumer, Level, ActiveHigh, Exclusive,,,) { 387 }
})
}
Also, since ATA driver should not require PCI support for ATA_ACPI,
this patch removes dependency in the driver/ata/Kconfig.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A relatively small setup of cleanups this time around, and similar to last time
the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0zof
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Kevin Hilman:
"A relatively small setup of cleanups this time around, and similar to
last time the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: fix EFM32 build breakage caused by cpu_resume_arm
ARM: 8389/1: Add cpu_resume_arm() for firmwares that resume in ARM state
ARM: v7 setup function should invalidate L1 cache
mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
ARM: OMAP2+: Constify irq_domain_ops
ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
ARM: at91: remove useless Makefile.boot
ARM: at91: remove at91rm9200_sdramc.h
ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
ARM: at91/pm: use the atmel-mc syscon defines
pcmcia: at91_cf: Use syscon to configure the MC/smc
ARM: at91: declare the at91rm9200 memory controller as a syscon
mfd: syscon: Add Atmel MC (Memory Controller) registers definition
ARM: at91: drop sam9_smc.c
ata: at91: use syscon to configure the smc
ARM: ux500: delete static resource defines
ARM: ux500: rename ux500_map_io
ARM: ux500: look up PRCMU resource from DT
ARM: ux500: kill off L2CC static map
...
Pull libata updates from Tejun Heo:
- a number of libata core changes to better support NCQ TRIM.
- ahci now supports MSI-X in single IRQ mode to support a new
controller which doesn't implement MSI or INTX.
- ahci now supports edge-triggered IRQ mode to support a new controller
which for some odd reason did edge-triggered IRQ.
- the usual controller support additions and changes.
* 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (27 commits)
libata: Do not blacklist Micron M500DC
ata: ahci_mvebu: add suspend/resume support
ahci, msix: Fix build error for !PCI_MSI
ahci: Add support for Cavium's ThunderX host controller
ahci: Add generic MSI-X support for single interrupts to SATA PCI driver
libata: finally use __initconst in ata_parse_force_one()
drivers: ata: add support for Ceva sata host controller
devicetree:bindings: add devicetree bindings for ceva ahci
ahci: added support for Freescale AHCI sata
ahci: Store irq number in struct ahci_host_priv
ahci: Move interrupt enablement code to a separate function
Doc: libata: Fix spelling typo found in libata.xml
ata:sata_nv - Change 1 to true for bool type variable.
ata: add Broadcom AHCI SATA3 driver for STB chips
Documentation: devicetree: add Broadcom SATA binding
libata: Fix regression when the NCQ Send and Receive log page is absent
ata: hpt366: fix constant cast warning
ata: ahci_xgene: potential NULL dereference in probe
ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.
libahci: Add support to handle HOST_IRQ_STAT as edge trigger latch.
...
Queued TRIM got disabled on Micron M500DC drives thanks to the
"Micron_M500*" pattern we had in place to accommodate the previous
generation of this drive family. Tweak the blacklist entry slightly so
we only disable queued TRIM for the non-DC variants of M500 drives.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
This commit adds suspend/resume support to the ahci_mvebu driver. The
suspend hook doesn't do anything special despite calling the generic
ahci_platform_suspend_host() function. However, the resume hook has to
restore the MBus windows configuration, as well as the regret option.
Tested on Marvell Armada 388 GP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
It turned out the irq vector of the msix can be obtained from struct
msix_entry. This makes the lookup function for msi_desc obsolete.
This fixes a build error if PCI_MSI is unset:
drivers/ata/ahci.c: In function ‘msix_get_desc’:
drivers/ata/ahci.c:1210:2: error: ‘struct pci_dev’ has no member named ‘msi_list’
Catched by Fengguang's build bot.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds support for Cavium's ThunderX host controller. The
controller resides on the SoC and is a AHCI compatible SATA controller
with one port, compliant with Serial ATA 3.1 and AHCI Revision 1.31.
There can exists multiple SATA controllers on the SoC.
The controller depends on MSI-X support since the PCI ECAM controller
on the SoC does not implement MSI nor lagacy intx interrupt support.
Thus, during device initialization, if MSI fails MSI-X will be used to
enable the device's interrupts.
The controller uses non-standard BAR0 for its register range. The
already existing device lookup (vendor and device id) that is already
implemented for other host controllers is used to change the PCI BAR.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds generic MSI-X support for single interrupts to the
SATA PCI driver. MSI-X support is needed for host controller that only
have MSI-X support implemented, but no MSI or intx. This patch only
adds support for single interrupts, multiple per-port MSI-X interrupts
are not yet implemented.
The new implementation still initializes MSIs first. Only if that
fails, the code tries to enable MSI-X. If that fails too, setup is
continued with intx interrupts.
To not break other chips by this generic code change, there are the
following precautions:
* Interrupt ranges are not enabled at all.
* Only single interrupt mode is enabled for msix cap devices. Thus,
only one interrupt will be setup.
* During the discussion with Tejun we agreed to change the init
sequence from msix-msi-intx to msi-msix-intx. Thus, if a device
offers msi and init does not fail, the msix init code will not be
executed. This is equivalent to current code.
With this, the code only setups single mode msix as a last resort if
msi fails. No interrupt range is enabled at all. Only one interrupt
will be enabled.
tj: comment edits.
Changes of the patch series:
v5:
* updated patch subject that the patch only implements single IRQ
* moved Cavium specific code to a separate patch
* detect Cavium ThunderX device with PCI_CLASS_STORAGE_SATA_AHCI
instead of vendor/dev id
* added more comments to the code
* enable single msix support for all kind of devices (removing strict
check)
* rebased onto update libata/for-4.2 with patch 1, 2 applied
v4:
* removed implementation of ahci_init_intx()
* improved patch descriptions
* rebased onto libata/for-4.2
v3:
* store irq number in struct ahci_host_priv
* change initialization order from msix-msi-intx to msi-msix-intx
* improve comments in ahci_init_msix()
* improve error message in ahci_init_msix()
* do not enable MSI-X if MSI is actively disabled for the device
v2:
* determine irq vector from pci_dev->msi_list
Based on a patch from Sunil Goutham <sgoutham@cavium.com>.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Just six days after this FIXME was added seven years ago, Sam Ravnborg
added the missing feature (37c514e3df "Add missing init section
definitions"), though it ended up being called __initconst.
Let's use it; better late than never.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Adds support for Ceva sata host controller on Xilinx
Zynq UltraScale+ MPSoC.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Freescale introduced QorIQ series SOCs, like ls1021 ls2085, with AHCI
sata support. It complies with the serial ATA 3.0 specification
and the AHCI 1.3 specification.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Yuantian Tang <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Two driver fixes. One is for an ahci_mvebu controller config bug and
the other fixes pata_octeon_cf build issue"
* 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
pata_octeon_cf: fix broken build
ata: ahci_mvebu: Fix wrongly set base address for the MBus window setting
MODULE_DEVICE_TABLE is referring to wrong driver's table and breaks the
build. Fix that.
Cc: stable@vger.kernel.org
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently, ahci supports only msi and intx. To also support msix the
handling of the irq number need to be changed. The irq number for msix
devices is taken from msi_list instead of pci_dev. Thus, the irq
number of a device needs to be stored in struct ahci_host_priv now.
This allows the host controller to be activated in a generic way.
This change is only intended for ahci drivers. For that reason the irq
number is stored in struct ahci_host_priv used only by ahci drivers.
Thus, the ABI changes only for ahci_host_activate(), but existing ata
drivers (about 50) are unaffected and keep unchanged. All users of
ahci_host_activate() have been updated.
While touching drivers/ata/libahci.c, doing a small code cleanup in
ahci_port_start().
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch refactors ahci_init_interrupts() and moves msi code to a
separate function. Need the split since we add msix initialization in
a later patch. The initialization for msix will be done after msi but
before intx.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fix a spelling typo found in libata.xml.
It is because libata.xml is generated from comments
in source, I have to fix it in libata-core.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
According to the Armada 38x datasheet, the window base address
registers value is set in bits [31:4] of the register and corresponds
to the transaction address bits [47:20].
Therefore, the 32bit base address value should be shifted right by
20bits and left by 4bits, resulting in 16 bit shift right.
The bug as not been noticed yet because if the memory available on
the platform is less than 2GB, then the base address is zero.
[gregory.clement@free-electrons.com: add extra-explanation]
Fixes: a3464ed2f1 (ata: ahci_mvebu: new driver for Marvell Armada 380
AHCI interfaces)
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Omri Itach <omrii@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The variable swncq_enabled is bool type. Hence initialize it
with true instead of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pretty straightforward driver, using the nice library-ization of the
generic ahci_platform driver.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 5d3abf8ff6 ("libata: Fall back to unqueued READ LOG EXT if
the DMA variant fails") allowed us to fall back to the unqueued READ
LOG variant if the queued version failed. However, if the device did
not support the page at all we would end up looping due to a merge
snafu.
Ensure we only take the fallback path once.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
gcc-5.x warns about a preexisting problem in the hpt36x pata driver:
drivers/ata/pata_hpt366.c: In function 'hpt36x_init_one':
drivers/ata/pata_hpt366.c:376:9: warning: assignment discards 'const' qualifier from pointer target type [-Wdiscarded-array-qualifiers]
Other ata drivers have the same problem, as ata_pci_bmdma_init_one
takes a non-const pointer, and they solve it by using a cast to
turn that pointer into a normal non-const pointer.
I also tried to change the ata core code to make host->private_data
a const pointer, but that quickly got out of hand, as some other
drivers expect it to be writable, so I ended up using the same
hack as the others here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use syscon/regmap to configure the smc. This allows to avoid using
at91sam9_smc.h and to compile the driver in a multiplatform configuration.
The driver will still not probe until the proper DT bindings are added. That
binding will include an atmel,smc property that is a phandle to the SMC the CF
controller is connected to.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Smatch complains about this potential NULL dereference of "acpi_id".
Fixes: c9802a4be6 ('ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Rather big for fixes pull.
- SCC controllers never lived to see the light of the day. Both
libata and ide drivers removed.
- In some configurations, link power management policy changes
sometimes cause delayed spurious PHY events which can develop into
noticeable failures. This has been reported several times over the
years. Gabriele's patches suppress PHY events for a while after
LPM policy changes which should help most of these failures without
causing too much problem for hotplug use cases.
- A few controller specific fixes"
[ Hmm. I don't think removing SSC support is really a "fix", but hey, it
removes a lot of lines of code. Which I like. So ... good riddance ]
* 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: avoton port-disable reset-quirk
ata: select DW_DMAC in case of SATA_DWC
libata: Blacklist queued TRIM on all Samsung 800-series
libata: Ignore spurious PHY event on LPM policy change
libata: Add helper to determine when PHY events should be ignored
ata: ahci_st: fixup layering violations / drvdata errors
Remove celleb-only SCC PATA drivers
This patch enables full AHCI feature support for APM X-Gene SoC SATA
host controller. The following errata's are removed:
1. 2a0bdff6b9 ("ahci-xgene: fix the dma state machine lockup for the
IDENTIFY DEVICE PIO mode command")
2. 09c32aaa36 ("ahci_xgene: Fix the dma state machine lockup for the
ATA_CMD_SMART PIO mode command")
3. 1540035da7 ("ahci_xgene: Implement the xgene_ahci_poll_reg_val to
support PMP")
4. a3a84bc7c8 ("ahci_xgene: Implement the workaround to support PMP
enumeration and discovery")
5. 1102407bb7 ("ahci_xgene: Fix the DMA state machine lockup for the
ATA_CMD_PACKET PIO mode command")
6. 72f79f9e35 ("ahci_xgene: Removing NCQ support from the APM X-Gene
SoC AHCI SATA Host Controller driver")
In addition, enable PMP support for APM X-Gene SoC and enable FBS
support for second generation APM X-Gene SoC.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds the support to handle HOST_IRQ_STAT as edge trigger
latch.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch refactors the ahci_single_irq_intr function and also rename
it to ahci_single_level_irq_intr as it handles a level triggered latch.
Signed-off-by: Suman tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Avoton AHCI occasionally sees drive probe timeouts at driver load time.
When this happens SCR_STATUS indicates device detected, but no D2H FIS
reception. Reset the internal link state machines by bouncing
port-enable in the PCS register when this occurs.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since sata_dwc_460ex.c was moved to generic DMA driver we have to ensure that
user can still compile it.
Fixes: 8b3444852a (sata_dwc_460ex: move to generic DMA driver)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some devices advertise support for the READ/WRITE LOG DMA EXT commands
but fail when we try to issue them. This can lead to queued TRIM being
unintentionally disabled since the relevant feature flag is located in a
general purpose log page.
Fall back to unqueued READ LOG EXT if the DMA variant fails while
reading a log page.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Create a sysfs "trim" attribute for each ata_device that displays
whether DSM TRIM is "unsupported", "unqueued", "forced_unqueued"
(blacklisted) or "queued".
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
We have started seeing SSD firmware updates introduce support for queued
TRIM. Sadly, in most cases this support is completely untested and can
lead to either errors or data corruption.
Add two libata force flags that can be used to either enable or disable
queued TRIM support.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The queued TRIM problems appear to be generic to Samsung's firmware and
not tied to a particular model. A recent update to the 840 EVO firmware
introduced the same issue as we saw on 850 Pro.
Blacklist queued TRIM on all 800-series drives while we work this issue
with Samsung.
Reported-by: Günter Waller <g.wal@web.de>
Reported-by: Sven Köhler <sven.koehler@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When the LPM policy is set to ATA_LPM_MAX_POWER, the device might
generate a spurious PHY event that cuases errors on the link.
Ignore this event if it occured within 10s after the policy change.
The timeout was chosen observing that on a Dell XPS13 9333 these
spurious events can occur up to roughly 6s after the policy change.
Link: http://lkml.kernel.org/g/3352987.ugV1Ipy7Z5@xps13
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This is a preparation commit that will allow to add other criteria
according to which PHY events should be dropped.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Brian noticed while working on another SATA driver that uses libahci_platform,
an error in this driver; it tries to the the driver data for its
device, while libata also thinks it can set the driver data. See:
ahci_platform_init_host()
-> ata_host_alloc_pinfo()
-> ata_host_alloc()
-> dev_set_drvdata()
So instead of sticking the IP-specific platform data into drvdata, let's
use the plat_data variable that is reserved for this use.
Addtionally plat_data isn't set until ahci_platform_init_host() has been
called further down in probe(). So re-work the st_ahci_probe_resets and
st_ahci_deassert_resets functions to take ahci_host_priv *hpriv as a
parameter.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Suggested-by: Brian Norris <computersforpeace@gmail.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was flashing
your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather than per
machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended transactions
on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree nodes, an
MSI erratum workaround, a couple minor performance improvements, config
updates, and misc fixes/cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=03Yh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
- Generic PM domains support update including new PM domain
callbacks to handle device initialization better (Russell King,
Rafael J Wysocki, Kevin Hilman).
- Unified device properties API update including a new mechanism
for accessing data provided by platform initialization code
(Rafael J Wysocki, Adrian Hunter).
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano).
- intel_idle update including support for the Silvermont Core in
the Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause).
- New cpufreq driver for Hisilicon ACPU (Leo Yan).
- intel_pstate update including support for the Knights Landing
chip (Dasaratharaman Chandramouli, Kristen Carlson Accardi).
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann).
- powernv cpufreq driver update (Shilpasri G Bhat).
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi).
- powercap RAPL (Running-Average Power Limit) driver update
including support for Intel Broadwell server chips (Jacob Pan,
Mathias Krause).
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki).
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng).
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems
and a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede).
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu).
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki).
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu).
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu).
- Configurable delay for the system suspend/resume testing facility
(Brian Norris).
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJVLbO+AAoJEILEb/54YlRx5N4QAJXsmEW1FL2l6mMAyTQkEsVj
nbqjF9I6aJgYM9+i8GKaZJxpN17SAZ7Ii7aCAXjPwX8AvjT70+gcZr+KDWtPir61
B75VNVEcUYOR4vOF5Z6rQcQMlhGPkfMOJYXFMahpOG6DdPbVh1x2/tuawfc6IC0V
a6S/fln6WqHrXQ+8swDSv1KuZsav6+8AQaTlNUQkkuXdY9b3k/3xiy5C2K26APP8
x1B39iAF810qX6ipnK0gEOC3Vs29dl7hvNmgOVmmkBGVS7+pqTuy5n1/9M12cDRz
78IQ7DXB0NcSwr5tdrmGVUyH0Q6H9lnD3vO7MJkYwKDh5a/2MiBr2GZc4KHDKDWn
E1sS27f1Pdn9qnpWLzTcY+yYNV3EEyre56L2fc+sh+Xq9sNOjUah+Y/eAej/IxYD
XYRf+GAj768yCJgNP+Y3PJES/PRh+0IZ/dn5k0Qq2iYvc8mcObyG6zdQIvCucv/i
70uV1Z2GWEb31cI9TUV8o5GrMW3D0KI9EsCEEpiFFUnhjNog3AWcerGgFQMHxu7X
ZnNSzudvek+XJ3NtpbPgTiJAmnMz8bDvBQm3G1LUO2TQdjYTU6YMUHsfzXs8DL6c
aIMWO4stkVuDtWrlT/hfzIXepliccyXmSP6sbH+zNNCepulXe5C4M2SftaDi4l/B
uIctXWznvHoGys+EFL+v
=erd3
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over, although there are a few
items that sort of fall into the new feature category.
First off, we have new callbacks for PM domains that should help us to
handle some issues related to device initialization in a better way.
There also is some consolidation in the unified device properties API
area allowing us to use that inferface for accessing data coming from
platform initialization code in addition to firmware-provided data.
We have some new device/CPU IDs in a few drivers, support for new
chips and a new cpufreq driver too.
Specifics:
- Generic PM domains support update including new PM domain callbacks
to handle device initialization better (Russell King, Rafael J
Wysocki, Kevin Hilman)
- Unified device properties API update including a new mechanism for
accessing data provided by platform initialization code (Rafael J
Wysocki, Adrian Hunter)
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano)
- intel_idle update including support for the Silvermont Core in the
Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause)
- New cpufreq driver for Hisilicon ACPU (Leo Yan)
- intel_pstate update including support for the Knights Landing chip
(Dasaratharaman Chandramouli, Kristen Carlson Accardi)
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)
- powernv cpufreq driver update (Shilpasri G Bhat)
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi)
- powercap RAPL (Running-Average Power Limit) driver update including
support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki)
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng)
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems and
a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu)
- Configurable delay for the system suspend/resume testing facility
(Brian Norris)
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
ACPI / scan: Rework modalias creation when "compatible" is present
intel_idle: mark cpu id array as __initconst
powercap / RAPL: mark rapl_ids array as __initconst
powercap / RAPL: add ID for Broadwell server
intel_pstate: Knights Landing support
intel_pstate: remove MSR test
cpufreq: fix qoriq uniprocessor build
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
PM / watchdog: iTCO: stop watchdog during system suspend
cpufreq: hisilicon: add acpu driver
ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
cpufreq: powernv: Report cpu frequency throttling
intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
intel_idle: Update support for Silvermont Core in Baytrail SOC
PM / devfreq: tegra: Register governor on module init
...
The SCC PATA interface is only used by celleb.
celleb has been dropped [1], so drop the drivers.
[1] http://patchwork.ozlabs.org/patch/451730/
CC: "David S. Miller" <davem@davemloft.net>
CC: linux-ide@vger.kernel.org
CC: Valentin Rothberg <valentinrothberg@gmail.com>
CC: mpe@ellerman.id.au
CC: linuxppc-dev@lists.ozlab.org
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
- Hannes's patchset implements support for better error reporting
introduced by the new ATA command spec.
- the deperecated pci_ dma API usages have been replaced by dma_ ones.
- a bunch of hardware specific updates and some cleanups.
* 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: remove deprecated use of pci api
ahci: st: st_configure_oob must be called after IP is clocked.
ahci: st: Update the ahci_st DT documentation
ahci: st: Update the DT example for how to obtain the PHY.
sata_dwc_460ex: indent an if statement
libata: Add tracepoints
libata-eh: Set 'information' field for autosense
libata: Implement support for sense data reporting
libata: Implement NCQ autosense
libata: use status bit definitions in ata_dump_status()
ide,ata: Rename ATA_IDX to ATA_SENSE
libata: whitespace fixes in ata_to_sense_error()
libata: whitespace cleanup in ata_get_cmd_descript()
libata: use READ_LOG_DMA_EXT
libata: remove ATA_FLAG_LOWTAG
sata_dwc_460ex: re-use hsdev->dev instead of dwc_dev
sata_dwc_460ex: move to generic DMA driver
sata_dwc_460ex: join messages back
sata: xgene: add ACPI support for APM X-Gene SATA ports
ata: sata_mv: add proper definitions for LP_PHY_CTL register values
* pnp:
PNP: Avoid leaving unregistered device objects in lists
PNP: Convert pnp_lock into a mutex
PNP: tty/serial/8250/8250_fintek: Use module_pnp_driver to register driver
PNP: platform/x86/apple-gmux: Use module_pnp_driver to register driver
PNP: net/sb1000: Use module_pnp_driver to register driver
PNP: media/rc: Use module_pnp_driver to register driver
PNP: ide/ide-pnp: Use module_pnp_driver to register driver
PNP: ata/pata_isapnp: Use module_pnp_driver to register driver
PNP: tpm/tpm_infineon: Use module_pnp_driver to register driver
PNP: Add helper macro for pnp_register_driver boilerplate
PNP / ACPI: Use ACPI_COMPANION_SET() during initialization
Currently the ahci_st driver will hang the system on probe, as the
st_configure_oob function does some register writes before the IP
is clocked. This patch moves the function call to after
ahci_platform_enable_resources (which enables the IP clock), and
resolves the hang.
Addtionally st_ahci_configure_oob should be called in the st_ahci_resume
function, so we also rectify that ensuring it is also called after
the IP clock has been enabled.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We shuffled some code around in 8b3444852a ('sata_dwc_460ex: move to
generic DMA driver') an accidentally deleted a tab character here. It
causes a Smatch warning "if statement not indented".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Blacklist queued TRIM on this drive for now.
Reported-by: Stefan Keller <linux-list@zahlenfresser.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CC: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Micron has released an updated firmware (MU02) for M510/M550/MX100
drives to fix the issues with queued TRIM. Queued TRIM remains broken on
M500 but is working fine on later drives such as M600 and MX200.
Tweak our blacklist to reflect the above.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71371
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Add some tracepoints for ata_qc_issue, ata_qc_complete, and
ata_eh_link_autopsy.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
If NCQ autosense or the sense data reporting feature is enabled
the LBA of the offending command should be stored in the sense
data 'information' field.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
ACS-4 defines a sense data reporting feature set.
This patch implements support for it.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some newer devices support NCQ autosense (cf ACS-4), so we should
be using it to retrieve the sense code and speed up recovery.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
If READ_LOG_DMA_EXT is supported we should try to use it for
reading the log pages.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
sata_sil24 for some reason pukes when tags are allocated round-robin
which helps tag ordered controllers. To work around the issue,
72dd299d50 ("libata: allow sata_sil24 to opt-out of tag ordered
submission") introduced ATA_FLAG_LOWTAG which tells libata tag
allocation to do lowest-first.
However, with the recent switch to blk-mq tag allocation, the liata
tag allocation code path is no longer used and the workaround is now
implemented in the block layer and selected by setting
scsi_host_template->tag_alloc_policy to BLK_TAG_ALLOC_FIFO. See
9269e23496 ("libata: make sata_sil24 use fifo tag allocator").
This leaves ATA_FLAG_LOWTAG withoout any actual user. Remove it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shaohua Li <shli@fb.com>
Cc: Dan Williams <dan.j.williams@intel.com>
This patch re-uses hsdev->dev which is allocated on heap. Therefore, the
private structure, which is global variable, is reduced by one field.
In one case ap->dev is used and there it seems to be right decision.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The SATA implementation based on two actually different devices, i.e. SATA and
DMA controllers.
For Synopsys DesignWare DMA we have already a generic implementation of the
driver. Thus, the patch converts the code to use DMAEngine framework and
dw_dmac driver.
In future it will be better to split the devices inside DTS as well like it's
done on other platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
It it better to have full message on one line. It simplifies to search for line
in the code by message when debugging.
Note that the lines which will be removed by sequential patch are not fixed
here.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ppc has special instruction forms to efficiently load and store values
in non-native endianness. These can be accessed via the arch-specific
{ld,st}_le{16,32}() inlines in arch/powerpc/include/asm/swab.h.
However, gcc is perfectly capable of generating the byte-reversing
load/store instructions when using the normal, generic cpu_to_le*() and
le*_to_cpu() functions eaning the arch-specific functions don't have much
point.
Worse the "le" in the names of the arch specific functions is now
misleading, because they always generate byte-reversing forms, but some
ppc machines can now run a little-endian kernel.
To start getting rid of the arch-specific forms, this patch removes them
from all the old Power Macintosh drivers, replacing them with the
generic byteswappers.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds ACPI support for the APM X-Gene SATA ports. When the system
boots using ACPI table, the SATA ports are able to configure using the
values supplied by the ACPI table rather than the DTS.
Signed-off-by: Feng Kan <fkan@apm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 9013d64e66 ("ata: sata_mv: fix disk hotplug for Armada
370/XP SoCs") added some manipulation of the LP_PHY_CTL register, but
using magic values. This commit changes the code to use proper
definitions for the LP_PHY_CTL register, which allows to document what
the different bits are doing.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
SAS controller has its own tag allocation, which doesn't directly match to ATA
tag, so SAS and SATA have different code path for ata tags. Originally we use
port->scsi_host (98bd4be1) to destinguish SAS controller, but libsas set
->scsi_host too, so we can't use it for the destinguish, we add a new flag for
this purpose.
Without this patch, the following oops can happen because scsi-mq uses
a host-wide tag map shared among all devices with some integer tag
values >= ATA_MAX_QUEUE. These unexpectedly high tag values cause
__ata_qc_from_tag() to return NULL, which is then dereferenced in
ata_qc_new_init().
BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
IP: [<ffffffff804fd46e>] ata_qc_new_init+0x3e/0x120
PGD 32adf0067 PUD 32adf1067 PMD 0
Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi igb
i2c_algo_bit ptp pps_core pm80xx libsas scsi_transport_sas sg coretemp
eeprom w83795 i2c_i801
CPU: 4 PID: 1450 Comm: cydiskbench Not tainted 4.0.0-rc3 #1
Hardware name: Supermicro X8DTH-i/6/iF/6F/X8DTH, BIOS 2.1b 05/04/12
task: ffff8800ba86d500 ti: ffff88032a064000 task.ti: ffff88032a064000
RIP: 0010:[<ffffffff804fd46e>] [<ffffffff804fd46e>] ata_qc_new_init+0x3e/0x120
RSP: 0018:ffff88032a067858 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff8800ba0d2230 RCX: 000000000000002a
RDX: ffffffff80505ae0 RSI: 0000000000000020 RDI: ffff8800ba0d2230
RBP: ffff88032a067868 R08: 0000000000000201 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800ba0d0000
R13: ffff8800ba0d2230 R14: ffffffff80505ae0 R15: ffff8800ba0d0000
FS: 0000000041223950(0063) GS:ffff88033e480000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000058 CR3: 000000032a0a3000 CR4: 00000000000006e0
Stack:
ffff880329eee758 ffff880329eee758 ffff88032a0678a8 ffffffff80502dad
ffff8800ba167978 ffff880329eee758 ffff88032bf9c520 ffff8800ba167978
ffff88032bf9c520 ffff88032bf9a290 ffff88032a0678b8 ffffffff80506909
Call Trace:
[<ffffffff80502dad>] ata_scsi_translate+0x3d/0x1b0
[<ffffffff80506909>] ata_sas_queuecmd+0x149/0x2a0
[<ffffffffa0046650>] sas_queuecommand+0xa0/0x1f0 [libsas]
[<ffffffff804ea544>] scsi_dispatch_cmd+0xd4/0x1a0
[<ffffffff804eb50f>] scsi_queue_rq+0x66f/0x7f0
[<ffffffff803e5098>] __blk_mq_run_hw_queue+0x208/0x3f0
[<ffffffff803e54b8>] blk_mq_run_hw_queue+0x88/0xc0
[<ffffffff803e5c74>] blk_mq_insert_request+0xc4/0x130
[<ffffffff803e0b63>] blk_execute_rq_nowait+0x73/0x160
[<ffffffffa0023fca>] sg_common_write+0x3da/0x720 [sg]
[<ffffffffa0025100>] sg_new_write+0x250/0x360 [sg]
[<ffffffffa0025feb>] sg_write+0x13b/0x450 [sg]
[<ffffffff8032ec91>] vfs_write+0xd1/0x1b0
[<ffffffff8032ee54>] SyS_write+0x54/0xc0
[<ffffffff80689932>] system_call_fastpath+0x12/0x17
tj: updated description.
Fixes: 12cb5ce101 ("libata: use blk taging")
Reported-and-tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Removing some boilerplate by using module_pnp_driver instead of calling
register and unregister in the otherwise empty init/exit functions
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The OF functionality has moved to a common place and be used by many
archs. So we don't need to include the ppc arch specific header files
and depend on PPC_OF option any more. This is a preparation for
killing PPC_OF.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The driver was ignoring limits requested by libata.force. The output
would look like:
fsl-sata ffe18000.sata: Sata FSL Platform/CSB Driver init
ata1: FORCE: PHY spd limit set to 1.5Gbps
ata1: SATA max UDMA/133 irq 74
ata1: Signature Update detected @ 0 msecs
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 310)
Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull block driver changes from Jens Axboe:
"This contains:
- The 4k/partition fixes for brd from Boaz/Matthew.
- A few xen front/back block fixes from David Vrabel and Roger Pau
Monne.
- Floppy changes from Takashi, cleaning the device file creation.
- Switching libata to use the new blk-mq tagging policy, removing
code (and a suboptimal implementation) from libata. This will
throw you a merge conflict, since a bug in the original libata
tagging code was fixed since this code was branched. Trivial.
From Shaohua.
- Conversion of loop to blk-mq, from Ming Lei.
- Cleanup of the io_schedule() handling in bsg from Peter Zijlstra.
He claims it improves on unreadable code, which will cost him a
beer.
- Maintainer update or NDB, now handled by Markus Pargmann.
- NVMe:
- Optimization from me that avoids a kmalloc/kfree per IO for
smaller (<= 8KB) IO. This cuts about 1% of high IOPS CPU
overhead.
- Removal of (now) dead RCU code, a relic from before NVMe was
converted to blk-mq"
* 'for-3.20/drivers' of git://git.kernel.dk/linux-block:
xen-blkback: default to X86_32 ABI on x86
xen-blkfront: fix accounting of reqs when migrating
xen-blkback,xen-blkfront: add myself as maintainer
block: Simplify bsg complete all
floppy: Avoid manual call of device_create_file()
NVMe: avoid kmalloc/kfree for smaller IO
MAINTAINERS: Update NBD maintainer
libata: make sata_sil24 use fifo tag allocator
libata: move sas ata tag allocation to libata-scsi.c
libata: use blk taging
NVMe: within nvme_free_queues(), delete RCU sychro/deferred free
null_blk: suppress invalid partition info
brd: Request from fdisk 4k alignment
brd: Fix all partitions BUGs
axonram: Fix bug in direct_access
loop: add blk-mq.h include
block: loop: don't handle REQ_FUA explicitly
block: loop: introduce lo_discard() and lo_req_flush()
block: loop: say goodby to bio
block: loop: improve performance via blk-mq
This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
megaraid_sas, ses) plus an assortment of minor updates. There's also an
update to ufs which adds new phy drivers and finally a new logging
infrastructure for SCSI.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJU2Ty5AAoJEDeqqVYsXL0M9rAH/1xNpAxXuxQq+dW5Z+uOaX60
5RRIu7/xA1HEfzkT5FTHrolmogDjVqawu4PZS66iHDeo05RBVUlbTA8qCK+MlRcN
U6s0cLEw59eH3EaCfOGuYp/MnbhuV0eNxe0btmqJIQwuW3+gwZKGJdOq6LS2YasJ
k/DyIBVmkJAVsN56vm9q2vbtcZp+Bg+ngqBS+SC4TF7vV1WCtFmS6yaUf62PYW3D
+Irx37qHZntDR5wdw3dsuKDi5U8bl6myPjaVLnVJqg/WIF9RlCkjk5xpWT99AmVO
NmtYQxLLBlAQ5K+sIlBUwxZe+8q1l+Aj4TTmJHAfFtyfp25s7JR9I6/QtOyC5Kw=
=odol
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
megaraid_sas, ses) plus an assortment of minor updates.
There's also an update to ufs which adds new phy drivers and finally a
new logging infrastructure for SCSI"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (114 commits)
scsi_logging: return void for dev_printk() functions
scsi: print single-character strings with seq_putc
scsi: merge consecutive seq_puts calls
scsi: replace seq_printf with seq_puts
aha152x: replace seq_printf with seq_puts
advansys: replace seq_printf with seq_puts
scsi: remove SPRINTF macro
sg: remove an unused variable
hpsa: Use local workqueues instead of system workqueues
hpsa: add in P840ar controller model name
hpsa: add in gen9 controller model names
hpsa: detect and report failures changing controller transport modes
hpsa: shorten the wait for the CISS doorbell mode change ack
hpsa: refactor duplicated scan completion code into a new routine
hpsa: move SG descriptor set-up out of hpsa_scatter_gather()
hpsa: do not use function pointers in fast path command submission
hpsa: print CDBs instead of kernel virtual addresses for uncommon errors
hpsa: do not use a void pointer for scsi_cmd field of struct CommandList
hpsa: return failed from device reset/abort handlers
hpsa: check for ctlr lockup after command allocation in main io path
...
Commit 84683a7e08 ("sata_dwc_460ex: enable COMPILE_TEST for the
driver") enabled this driver for non-ppc460-ex platforms, but it was
then disabled for ARM and ARM64 by commit 2de5a9c004 ("sata_dwc_460ex:
disable compilation on ARM and ARM64") because it's too noisy and
broken.
This disabled is entirely, because it's too noisy on x86-64 too, and
there's no point in disabling architectures one by one. At a minimum,
the code isn't 64-bit clean, and even on 32-bit it is questionable
whether it makes sense.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
09c32aaa36 ("ahci_xgene: Fix the dma state machine lockup for the
ATA_CMD_SMART PIO mode command.") missed 3.19 release. Fold it into
for-3.20.
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch addresses the issue with ATA_CMD_SMART pio mode command for
enumeration and device detection with ATA devices. The X-Gene AHCI
controller has an errata in which it cannot clear the BSY bit after
the PIO setup FIS. The dma state machine enters CMFatalErrorUpdate
state and locks up. It is the same issue as in the commit 2a0bdff6b9
("ahci-xgene: fix the dma state machine lockup for the IDENTIFY DEVICE
PIO mode command").
For example : without this patch it results in READ DMA command failure
as shown below :
[ 126.700072] ata2.00: exception Emask 0x0 SAct 0x0
SErr 0x0 action 0x6 frozen
[ 126.707089] ata2.00: failed command: READ DMA
[ 126.711426] ata2.00: cmd c8/00:08:00:55:57/00:00:00:00:00/e1 tag 1
dma 4096 in
[ 126.711426] res 40/00:ff:00:00:00/00:00:00:00:00/40 Emask
0x4 (timeout)
[ 126.725956] ata2.00: status: { DRDY }
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Reported-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
of_platform_device_create does not exist if OF_ADDRESS is not configured,
so limit its use accordingly.
Without this fix, the sparc64:allmodconfig build fails with
ERROR: "of_platform_device_create" [drivers/ata/libahci_platform.ko] undefined!
Fixes: c7d7ddee7e ("ata: libahci: Allow using multiple regulators")
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
The phy_power_off() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
The pci_dev_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
The owner module reference of the pata_of_platform's scsi_host is
initialized to pata_platform's one, because pata_of_platform driver
use a scsi_host_template defined in pata_platform. So this drivers
can be unloaded even if the scsi device is being accessed.
This fixes it by propagating the scsi_host_template to pata_of_platform
driver. The scsi_host_template is passed through a new
argument of __pata_platform_probe().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-ide@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
The owner module reference of the ahci platform's scsi_host is
initialized to libahci_platform's one, because these drivers use a
scsi_host_template defined in libahci_platform. So these drivers can
be unloaded even if the scsi device is being accessed.
This fixes it by pushing the scsi_host_template from libahci_platform
to all leaf drivers. The scsi_host_template is passed through a new
argument of ahci_platform_init_host().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-ide@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Function pdc_detect_pll_input_clock uses 'struct timeval'
to measure start and end times, used to compute the pll_clock value.
'struct timeval' on 32-bit systems will have its tv_sec field
overflow in year 2038 and beyond. This patch uses 'ktime_t'
(which uses 64 bits for seconds) for start and end times instead.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
libata starts using block tag now, we can use BLK_TAG_ALLOC_FIFO to
solve the sata_sil24 tag bug.
https://bugzilla.kernel.org/show_bug.cgi?id=87101
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Basically move the sas ata tag allocation to libata-scsi.c to make it clear
these staffs are just for sas.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
