Add definitions for the ASID field in CP0_EntryHi (along with the soon
to be used ASIDX field), and use them in a few previously hardcoded
cases.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13205/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS KVM uses different ASIDs for guest execution than for the host.
The host ASID is saved on the stack when entering the guest with
__kvm_mips_vcpu_run(), and restored again before returning back to the
caller (exit to userland).
- This does not take into account that pre-emption may have taken place
during that time, which may have started a new ASID cycle and resulted
in that process' ASID being invalidated and reused.
- This does not take into account that the process may have migrated to
a different CPU during that time, with a different ASID assignment
since they are managed per-CPU.
- It is actually redundant, since the host ASID will be restored
correctly by kvm_arch_vcpu_put(), which is called almost immediately
after kvm_arch_vcpu_ioctl_run() returns.
Therefore drop this code from locore.S
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13206/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Release 6 of the MIPS architecture introduced the bitswap instruction,
which reverses the bits within each byte of a word. Make use of this
instruction to implement the __arch_bitrev* functions, which should be
faster for most MIPSr6 CPUs, reduces code size slightly and allows us to
avoid the lookup table used by the generic implementation, saving 256
bytes in the kernel binary by dropping that.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13204/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit 3b9d6da67e ("cpu/hotplug: Fix rollback during error-out
in __cpu_disable()") it is ensured that callbacks of CPU_ONLINE and
CPU_DOWN_PREPARE are processed on the hotplugged CPU. Due to this
work_on_cpu() calls are no longer required.
Replace work_on_cpu() with a direct call of mips_cdmm_bus_up() or
mips_cdmm_bus_down(). Description of those functions are adapted.
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: rt@linutronix.de
Patchwork: https://patchwork.linux-mips.org/patch/13197/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No one of supported MIPS machines has an IOMMU unit, so we can safely define
PCI_DMA_BUS_IS_PHYS = 1. Also remove iommu flag from the pci controller
structure, since it is useless.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7604/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
New Loongson 3 CPU (since Loongson-3A R2, as opposed to Loongson-3A R1,
Loongson-3B R1 and Loongson-3B R2) has many enhancements, such as FTLB,
L1-VCache, EI/DI/Wait/Prefetch instruction, DSP/DSPv2 ASE, User Local
register, Read-Inhibit/Execute-Inhibit, SFB (Store Fill Buffer), Fast
TLB refill support, etc.
This patch introduce a config option, CONFIG_LOONGSON3_ENHANCEMENT, to
enable those enhancements which are not probed at run time. If you want
a generic kernel to run on all Loongson 3 machines, please say 'N'
here. If you want a high-performance kernel to run on new Loongson 3
machines only, please say 'Y' here.
Some additional explanations:
1) SFB locates between core and L1 cache, it causes memory access out
of order, so writel/outl (and other similar functions) need a I/O
reorder barrier.
2) Loongson 3 has a bug that di instruction can not save the irqflag,
so arch_local_irq_save() is modified. Since CPU_MIPSR2 is selected
by CONFIG_LOONGSON3_ENHANCEMENT, generic kernel doesn't use ei/di
at all.
3) CPU_HAS_PREFETCH is selected by CONFIG_LOONGSON3_ENHANCEMENT, so
MIPS_CPU_PREFETCH (used by uasm) probing is also put in this patch.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J . Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12755/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-3A R2 has pwbase/pwfield/pwsize/pwctl registers in CP0 (this
is very similar to HTW) and lwdir/lwpte/lddir/ldpte instructions which
can be used for fast TLB refill.
[ralf@linux-mips.org: Resolve conflict.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J . Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12754/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-2 has a 4 entry itlb which is a subset of jtlb, Loongson-3 has
a 4 entry itlb and a 4 entry dtlb which are subsets of jtlb. We should
write diag register to invalidate itlb/dtlb when flushing jtlb because
itlb/dtlb are not totally transparent to software.
For Loongson-3A R2 (and newer), we should invalidate ITLB, DTLB, VTLB
and FTLB before we enable/disable FTLB.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J . Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12753/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-3 maintains cache coherency by hardware, this means:
1) It's icache is coherent with dcache.
2) It's dcaches don't alias (maybe depend on PAGE_SIZE).
3) It maintains cache coherency across cores (and for DMA).
So we can skip most cache flush operations by setting relevant handlers
to `cache_noop' in `r4k_cache_init'.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J . Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12752/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adjust the logic in mach_irq_dispatch(), allow multiple IPs
handled in the same dispatching. This can speedup interrupt processing.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J . Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12891/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
SB700/SB710/SB800 chipset ACPI code is mostly Loongson-3 specific
routines rather than a "platform driver".
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11273/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Strip some comments which probably meant to repeat the same value of the
define; they also contained a confusing 0x0x prefix.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12254/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The files watch.c and ptrace.c contain various magic masks for
WatchLo/WatchHi register fields. Add some definitions to mipsregs.h for
these registers and make use of them in both watch.c and ptrace.c,
hopefully making them more readable.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12729/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
do_watch() clears bit 22 of cause without using a CAUSEF_* definition
from mipsregs.h. Add a definition for this bit (CAUSEF_WP) and make use
of it. Also use clear_c0_cause() instead of manual read/modify/write.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12728/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds support for the deadman timer peripheral found on PIC32 class devices.
The primary function of the deadman timer (DMT) is to reset the processor
in the event of a software malfunction. The DMT is a free-running
instruction fetch timer, which is clocked whenever an instruction fetch
occurs until a count match occurs. Instructions are not fetched when
the processor is in sleep mode.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12703/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IS_ERR_VALUE macro should be used only with unsigned long type.
Specifically it works incorrectly with longer types.
The patch follows conclusion from discussion on LKML [1][2].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2120927
[2]: http://permalink.gmane.org/gmane.linux.kernel/2150581
[ralf@linux-mips.org: While it may not immediately be obvious, the type
of st_value in the end is an unsigned long equivalent so the invocation
of IS_ERR_VALUE() was valid but I'm applying the patch anyway for
clarity.]
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12553/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Propagate sNaN payload in quieting in the legacy-NaN mode as well. If
clearing the quiet bit would produce infinity, then set the next lower
trailing significand field bit, matching the SB-1 and BMIPS5000 hardware
implementations. Some other MIPS FPU hardware implementations do
produce the default qNaN bit pattern instead.
This reverts some changes made for semantics preservation with commit
dc3ddf42 [MIPS: math-emu: Update sNaN quieting handlers], consequently
bringing back most of the semantics from before commit fdffbafb [Lots of
FPU bug fixes from Kjeld Borch Egevang.], except from the qNaN produced
in the infinity case. Previously the default qNaN bit pattern was
produced in that case.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11483/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update the ELF personality macros used for individual ABIs to make
actions in the same order across all of them and match formatting too.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit 8cb48fe169 ("MIPS: Provide correct siginfo_t.si_stime"),
MIPS' uapi/asm/siginfo.h has included uapi/asm-generic/siginfo.h
directly before defining MIPS' struct siginfo, in order to get the
necessary definitions needed for the siginfo struct without the generic
copy_siginfo() hitting compiler errors due to struct siginfo not yet
being defined.
Now that the generic copy_siginfo() is moved out to linux/signal.h we
can safely include asm-generic/siginfo.h before defining the MIPS
specific struct siginfo, which avoids the uapi/ include as well as
breakage due to generic copy_siginfo() being defined before struct
siginfo.
Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 8cb48fe169 ("MIPS: Provide correct siginfo_t.si_stime")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Petr Malat <oss@malat.biz>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.0-
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The generic copy_siginfo() is currently defined in
asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which
defines the generic struct siginfo. However this makes it awkward for an
architecture to use it if it has to define its own struct siginfo (e.g.
MIPS and potentially IA64), since it means that asm-generic/siginfo.h
can only be included after defining the arch-specific siginfo, which may
be problematic if the arch-specific definition needs definitions from
uapi/asm-generic/siginfo.h.
It is possible to work around this by first including
uapi/asm-generic/siginfo.h to get the constants before defining the
arch-specific siginfo, and include asm-generic/siginfo.h after. However
uapi headers can't be included by other uapi headers, so that first
include has to be in an ifdef __kernel__, with the non __kernel__ case
including the non-UAPI header instead.
Instead of that mess, move the generic copy_siginfo() definition into
linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to
include asm-generic/siginfo.h and define the arch-specific siginfo, and
for the generic copy_siginfo() to see that arch-specific definition.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Petr Malat <oss@malat.biz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Christopher Ferris <cferris@google.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # 4.0-
Patchwork: https://patchwork.linux-mips.org/patch/12478/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Just to ease debugging of multiplatform kernel, make sure we print
"Broadcom BMIPS5200" for the BMIPS5200 implementation instead of
Broadcom BMIPS5000.
Fixes: 68e6a78373 ("MIPS: BMIPS: Add PRId for BMIPS5200 (Whirlwind)")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13014/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BMIPS_GENERIC being multiplatform and intended to support BMIPS3200,
BMIPS3300, BMIPS4350, BMIPS4380 and BMIPS5000-class processors, there is
not much more we can put in there since they do not share the same I and
D cache line sizes at all (doubled for every new generation
essentially), some processors have a S-cache, some don't, some have a
FPU, some don't.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13013/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
local_r4k___flush_cache_all() is missing a special check for BMIPS5000
processors, we need to blast the S-cache, just like other MTI processors
since we have an inclusive cache. We also need an additional __sync() to
make sure this is completed.
Fixes: d74b0172e4 ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13012/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BMIPS5000 and BMIPS5200 processor have no D cache aliases, and this is
properly handled by the per-CPU override added at the end of
r4k_cache_init(), the problem is that the output of probe_pcache()
disagrees with that, since this is too late:
Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
With the change moved earlier, we now have a consistent output with the
settings we are intending to have:
Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes.
Primary data cache 32kB, 4-way, VIPT, no aliases, linesize 32 bytes
Fixes: d74b0172e4 ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13011/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BMIPS5000 and BMIPS52000 processors have their I-cache filling from the
D-cache. Since BMIPS_GENERIC does not provide (yet) a
cpu-feature-overrides.h file, this was not set anywhere, so make sure
the R4K cache detection takes care of that.
Fixes: d74b0172e4 ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13010/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable CONFIG_MTD_BCM63XX_PARTS in arch/mips/configs/bmips_be_defconfig
since this is a necessary option to parse the built-in flash partition
table on BMIPS big-endian SoCs (Cable Modem and DSL).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12256/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
