On dm814x we have 13 ADPLLs with 3 to 4 outputs on each. The
ADPLLs have several dividers and muxes controlled by a shared
control register for each PLL.
Note that for the clocks to work as device drivers for booting on
dm814x, this patch depends on "ARM: OMAP2+: Change core_initcall
levels to postcore_initcall" that has already been merged.
Also note that this patch does not implement clk_set_rate for the
PLL, that will be posted later on when available.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
On dm816x the clocks are sourced from a FAPLL (Flying Adder PLL)
that does not seem to be used on the other omap variants.
There are four instances of the FAPLL on dm816x that each have three
to seven child synthesizers.
I've set up the FAPLL as a single fapll.c driver. Later on we could
potentially have the PLL code generic. To do that, we would have to
consider the following:
1. Setting the PLL to bypass mode also sets the child synthesizers
into bypass mode. As the bypass rate can also be generated by
the PLL in regular mode, there's no way for the child synthesizers
to detect the bypass mode based on the parent clock rate.
2. The PLL registers control the power for each of the child
syntheriser.
Note that the clocks are currently still missing the set_rate
implementation so things are still running based on the bootloader
values. That's OK for now as most of the outputs have dividers and
those can be set using the existing TI component clock code.
I have verified that the extclk rates are correct for a few clocks,
so adding the set_rate support should be fairly trivial later on.
This code is partially based on the TI81XX-LINUX-PSP-04.04.00.02
patches published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
MPU DPLL on OMAP5, DRA75x, DRA72x has a limitation on the maximum
frequency it can be locked at. Duty Cycle Correction circuit is used
to recover a correct duty cycle for achieving higher frequencies
(hardware internally switches output to M3 output(CLKOUTHIF) from M2
output (CLKOUT)).
So provide support to setup required data to handle Duty cycle by
the setting up the minimum frequency for DPLL. 1.4GHz is common
for all these devices and is based on Technical Reference Manual
information for OMAP5432((SWPU282U) chapter 3.6.3.3.1 "DPLLs Output
Clocks Parameters", and equivalent information from DRA75x, DRA72x
documentation(SPRUHP2E, SPRUHI2P).
Signed-off-by: Nishanth Menon <nm@ti.com>
[t-kristo@ti.com: updated for latest dpll init API call]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Audio Tracking Logic is designed to be used by HD Radio applications to
synchronize the audio output clocks to the baseband clock. ATL can be also
used to track errors between two reference clocks (BWS, AWS) and generate a modulated
clock output which averages to some desired frequency.
In essence ATL is generating a clock to be used by an audio codec and also
to be used by the SoC as MCLK.
To be able to integrate the ATL provided clocks to the clock tree we need
two types of DT binding:
- DT clock nodes to represent the ATL clocks towards the CCF
- binding for the ATL IP itself which is going to handle the hw
configuration
The reason for this type of setup is that ATL itself is a separate device
in the SoC, it has it's own address space and clock domain. Other IPs can
use the ATL generated clock as their functional clock (McASPs for example)
and external components like audio codecs can also use the very same clock
as their MCLK.
The ATL IP in DRA7 contains 4 ATL instences.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP2430 I2CHS modules require specific hardware ops to be used, so added
a new compatible string for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP2 has slightly different DPLL compared to later OMAP generations.
This patch adds support for the ti,omap2-dpll-core-clock and also adds
the bindings documentation.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP3 has interface clocks in addition to functional clocks, which
require special handling for the autoidle and idle status register
offsets mainly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The patch adds support for DRA7 PCIe APLL. The APLL
sources the optional functional clocks for PCIe module.
APLL stands for Analog PLL. This is different when comapred
with DPLL meaning Digital PLL, the phase detection is done
using an analog circuit.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
ti,mux-clock provides now a binding for basic mux support. This is just
using the basic clock type.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some OMAP clocks require knowledge about their parent clockdomain for
book keeping purposes. This patch creates a new DT binding for TI
clockdomains, which act as a collection of device clocks. Clockdomain
itself is rather misleading name for the hardware functionality, as at
least on OMAP4 / OMAP5 / DRA7 the clockdomains can be collections of either
clocks and/or IP blocks, thus idle-domain or such might be more appropriate.
For most cases on these SoCs, the kernel doesn't even need the information
and the mappings can be ignored.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support for TI specific gate clocks. These behave as basic
gate-clock, but have different ops / hw-ops for controlling the actual
gate, for example waiting until the clock is ready. Several sub-types
are supported:
- ti,gate-clock: basic gate clock with default ops/hwops
- ti,clkdm-gate-clock: clockdomain level gate control
- ti,dss-gate-clock: gate clock with DSS specific hardware handling
- ti,am35xx-gate-clock: gate clock with AM35xx specific hardware handling
- ti,hsdiv-gate-clock: gate clock with OMAP36xx hardware errata handling
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This behaves exactly in similar manner to basic fixed-factor-clock, but
adds a few properties on top for handling clock hardware autoidling.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support for TI divider clock binding, which simply uses
the basic clock divider to provide the features needed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This is a multipurpose clock node, which contains support for multiple
sub-clocks. Uses basic composite clock type to implement the actual
functionality, and TI specific gate, mux and divider clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
TI clk driver now routes some of the basic clocks through own
registration routine to allow autoidle support. This routine just
checks a couple of device node properties and adds autoidle support
if required, and just passes the registration forward to basic clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The OMAP clock driver now supports DPLL clock type. This patch also
adds support for DT DPLL nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
