The X2 crystal oscillator on the Koelsch development board provides a
74.25 MHz clock, not a 148.5 MHz clock.
Fixes: cd21cb46e1 ("ARM: shmobile: koelsch: Add DU external pixel clocks to DT")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
I disabled SRAM and GPMC originally when seeing errors with
omap_barriers_init(). But that is no longer happening probably
because the memory range is now properly configured to 1021 MB
instead of 1024 MB. So let's enable SRAM and GPMC so we get
omap_barriers_init() working and can idle the GPMC.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CPCAP PMIC interrupt is level high sensitive despite it being
requested as edge high triggered in the Motorola Linux kernel.
Note that also the related driver change is needed posted as
"mfd: cpcap: Fix interrupt to use level interrupt".
Fixes: 56e1d40d3b ("mfd: cpcap: Add minimal support")
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the 2 ethernet ports as CPSW ports in dual-mac mode
Signed-off-by: Roger Quadros <rogerq@ti.com>
[nsekhar@ti.com: use AM33XX_IOPAD()]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM571x IDK and the AM572x IDK use CAN1 interface.
This patch enables it for both boards.
Tested on AM572x IDK using cansequence.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[nsekhar@ti.com: move to use DRA7XX_CORE_IOPAD())
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now we have driver for the PRCM CCU, switch to use it instead of
old-style clock nodes for apb0-related clocks in sunxi-h3-h5.dtsi .
The mux 3 of R_CCU is still the internal oscillator, which is said to be
16MHz plus minus 30%, and get a measured value of 15MHz~16MHz on my two
H3 boards and one H5 board.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 SoC has an on-board CAN controller. This patch adds
the pinctrl settings for pins PH20 and PH21.
This patch is adapted from the description in
Documentation/devicetree/bindings/net/can/sun4i_can.txt
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 SoC has an on-board CAN controller.
This patch adds the device node.
The CAN controller is inherited from the A10 SoC and uses the same driver.
This patch is adapted from the description in
Documentation/devicetree/bindings/net/can/sun4i_can.txt
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10 SoC has an on-board CAN controller. This patch adds the
pinctrl settings for pins PH20 and PH21.
This patch is adapted from the description in
Documentation/devicetree/bindings/net/can/sun4i_can.txt
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10 SoC has an on-board CAN controller.
This patch adds the device node.
This patch is adapted from the description in
Documentation/devicetree/bindings/net/can/sun4i_can.txt
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Cubietruck has an AXP209 PMIC and can be power-supplied by ACIN via
the CHG-IN pin or by USB.
This enables the ACIN and the USB power supply subnode in the DT.
Signed-off-by: Alexander Syring <alex@asyring.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the Z2 clock (Cortex-A7 CPU core clock), which uses a fixed divider,
and link the first CPU node to it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Unlike other R-Car Gen2 SoCs with Cortex-A15 CPU cores, R-Car V2H does
not have a programmable Z clock (Cortex-A15 CPU core clock), but uses a
fixed divider.
This is similar to the Z2 clock (Cortex-A7 CPU core clock) on R-Car E2.
Hence:
- Remove the Z clock output from the cpg_clocks node, as this implied
a programmable clock,
- Add the Z clock as a fixed factor clock,
- Let the first CPU node point to the new Z clock,
- Remove the Z clock index from the bindings (this definition was used
by r8a7792.dtsi only, and was not a contract between DT and driver).
Fixes: 7c4163aae3 ("ARM: dts: r8a7792: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SSI-ALL gate clock is located in between the P clock and the
individual SSI[0-9] clocks, hence the former should be listed as their
parent.
Fixes: 072d326542 ("ARM: dts: r8a7793: add MSTP10 clocks to device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SSI-ALL gate clock is located in between the P clock and the
individual SSI[0-9] clocks, hence the former should be listed as their
parent.
Fixes: ee9141522d ("ARM: shmobile: r8a7791: add MSTP10 support on DTSI")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SSI-ALL gate clock is located in between the P clock and the
individual SSI[0-9] clocks, hence the former should be listed as their
parent.
Fixes: bcde372254 ("ARM: shmobile: r8a7790: add MSTP10 support on DTSI")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Technically, the Ethernet block is run off the 133MHz Bus (B) clock, not
the 33MHz Peripheral 0 (P0) clock.
Fixes: 969244f9c7 ("ARM: dts: r7s72100: add ethernet clock to device tree")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables USB HS working in FS mode on stm32f429-disco
with 5V VBUS enable.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch enables USB FS on stm32f469-disco with 5V VBUS enable.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch adds the USB pins and nodes for USB FS core.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Update the Alpine clock-frequency values with valid default values. The
bootloader can still update these values if needed, but at least we can
boot if it does not.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Cosmetic cleanup to have consistent node definitions. Add a space before
the node units which do not have one.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
At this time, most of changes are for ASoC, while we got one fix for
yet another race of ALSA sequencer core and a usual HD-audio quirk.
The ASoC changes are mostly small and device-specific fixes. A
slightly large volume is seen in sun8i-codec, which is a new code in
4.11, and we'd like to fix user-visible stuff before the official 4.1
release.
-----BEGIN PGP SIGNATURE-----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=qutY
-----END PGP SIGNATURE-----
Merge tag 'sound-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"At this time, most of changes are for ASoC, while we got one fix for
yet another race of ALSA sequencer core and a usual HD-audio quirk.
The ASoC changes are mostly small and device-specific fixes. A
slightly large volume is seen in sun8i-codec, which is a new code in
4.11, and we'd like to fix user-visible stuff before the official 4.1
release"
* tag 'sound-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (27 commits)
ALSA: hda - fix a problem for lineout on a Dell AIO machine
ASoC: simple-card: fix simple_dai clk lookup
ASoC: STI: Fix reader substream pointer set
ALSA: seq: Fix race during FIFO resize
ARM: dts: sun8i: Update audio-routing with renamed widgets
ASoC: sun8i-codec: Convert to use SND_SOC_DAPM_AIF_IN
ASoC: sun8i-codec: Fix space on audio-routing widget
ASoC: sun8i-codec: Update mixer to use SOC_DAPM_DOUBLE
ASoC: sun8i-codec: Remove analog "HP" widget
ASoC: rt5665: fix wrong shift rt5665_if2_1_adc_in_enum
ASoC: rt5665: fix define of RT5665_HP_DRIVER_5X
ASoC: rcar: dma: remove unnecessary "volatile"
ASoC: rcar: clear DE bit only in PDMACHCR when it stops
ASoC: rsnd: fix sound route path when using SRC6/SRC9
ASoC: don't dereference NULL pcm_{new,free}
ASoC: rt5665: CLKDET is also a power of ASRC
ASoC: rt5665: Vref3 is necessary for Mono Amp
ASoC: rt5665: increase LDO level
ASoC: rt5665: fix getting wrong work handler container
ASoC: atmel-classd: fix audio clock rate
...
There was a little conflict between the v4.11 bugfixes and the new changes for 4.12,
this merges the fixes into the 4.12 branch to avoid having to resolve it again.
* Broadcom fixes in mainline
ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
ARM: dts: BCM5301X: Fix memory start address
ARM: dts: BCM5301X: Fix UARTs on bcm953012k
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add hecc node for am35x
- Add onenand support for omap3-igep
- Add bluetooth binding for n900/n9/n950
- Configure clocks and SATA for dm81xx
- Update operating points tables for am33xx, am43xx and dra7
- Update SPI flash documentation for w25q64
- Configure SPI NOR for am335x-icev2
- Mux uart0 for am437x-gp-evm
- Add thermal zones for omap3, omap4, omap5, dra7
- Configure LEDs for am335x-baltos
- A series of droid 4 changes to configure various devices
such as keypad, regulators, gpio-keys, rtc, power button,
compass, accelerometer, touchscreen, backlight, poweroff,
tmp105, HDMI, LCD panel and LEDs, EHCI, and micro-SD
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAlja1soRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXPS9hAAsFKL0gkbNG+u0P12y73IShSgt0Xhffmq
ChwdxMsRrPi5IJEOyPjcn3/HzWibBb/v+do1LIIM9i8Q+PchX+6DgssTYZEq5CAZ
szMvwNfqrT2AmV2iwM4u6xOaM+hAY9RoAtYikQpJ8Wm6vH9Dgy1Ve4ge2NmKna6P
0wnRJHIBJOzfGq4cP75QXqy2m/LJ4wwmP8pVzVa/9l/XtFlrsNT7n/kQ203PgYtR
k/nkr/Z3XEyY/nCaKosUbHS6o+CCMcxpdF2RjWcrlqvHg4xdm8eB+ilJh3be0eWH
7NMakynGXuqiI5lCqLeOpkBftD/kqSTojYuSY11nOhT+hHtoRe+KbOWYTf5UK7vb
rGXERxoZYm0WVtePDPAb+cyc7XdPTmqkXMJwCBKfomcndgcSQJqYgeUv380+5blF
76rhOq3xiKEDOPly8tjDS+4saZ+zEHj6dINhu+Lv56uQJCm0Y7o0j/RO4KMmZYAv
Ht71lOM7xNEAhw/Opk03A1ERkQNDuK1lmjW4M5hmHDskboB0RLOnGBLDDvWBIH/Q
H129hbDyEjEgMqgTuZi3cEt83jvQ0clzwjnmDDBW9O/nk1OpUHzPD4MMELNo+hBR
g1BOKjAQ6nwN3yV9i+eyiY+nk822Hu1L5CpXXDrP0XZlVOhGFbSS+6/uCztfBhcl
p7uZtAidu68=
=CRcK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.12/dt-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Devicetree changes for omaps for v4.12 merge window" from Tony Lindgren:
- Add hecc node for am35x
- Add onenand support for omap3-igep
- Add bluetooth binding for n900/n9/n950
- Configure clocks and SATA for dm81xx
- Update operating points tables for am33xx, am43xx and dra7
- Update SPI flash documentation for w25q64
- Configure SPI NOR for am335x-icev2
- Mux uart0 for am437x-gp-evm
- Add thermal zones for omap3, omap4, omap5, dra7
- Configure LEDs for am335x-baltos
- A series of droid 4 changes to configure various devices
such as keypad, regulators, gpio-keys, rtc, power button,
compass, accelerometer, touchscreen, backlight, poweroff,
tmp105, HDMI, LCD panel and LEDs, EHCI, and micro-SD
* tag 'omap-for-v4.12/dt-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (35 commits)
ARM: dts: am335x-baltos: add LED support
ARM: dts: omap4-droid4: Fix MMC1 card for detect GPIO and regulator
ARM: dts: OMAP4460: Thermal: Add slope and offset values
ARM: dts: OMAP443x: Thermal: Add slope and offset values
ARM: dts: OMAP5: Thermal: Add slope and offset values
ARM: dts: DRA7: Thermal: Add slope and offset values
ARM: dts: omap3: Add cpu_thermal zone
ARM: dts: am437x-gp-evm: Add pinmux for uart0
ARM: dts: am335x-icev2: Add SPI based NOR
Documentation: devicetree: mtd: add w25q64 to list of supported SPI flashes
ARM: dts: dra7: Add updated operating-points-v2 table for cpu
ARM: dts: am4372: Update operating-points-v2 table for cpu
ARM: dts: am335x-boneblack: Enable 1GHz OPP for cpu
ARM: dts: am33xx: Add updated operating-points-v2 table for cpu
ARM: dts: dm8168-evm: add SATA node
ARM: dts: dm8168-evm: add the external reference clock for SATA
ARM: dts: N9/N950: add bluetooth
ARM: dts: N900: Add bluetooth
ARM: dts: omap4-droid4: Configure EHCI so modems can be accessed
ARM: dts: motorola-cpcap-mapphone: add LEDs
...
definitions for the mmc resets in the socs reset controller, sound
support for the Rock2, dma support for mmc controllers on the rk3188
and a led-fix for the MiQi board and and irq-fix for older Cortex-A9 socs.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAljY6NUQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgTORB/49/3AhQ9neAjN5igVGMxv2PX5OPkYz07wJ
AgPPyUDBchXIU2teAuPzv/T9rS0wAJR58qLL7JiYjYz+II/XE3qWJUjiT5p5mjsp
ko4ijesWraf5C7z2ltL0T25lIyZwkjCJgjMzIxLMOsDgF4nN1yBxYh18CXXyc3sL
G3GYVGwEAhM9EwFjzrpyL7guFe2ZiKAZ7QmVeLmsDT9goECgz1XebuM+3idbOwJB
JjhmOmiSuUAHZO6o3soOZiDzb6xD9MELp/5a6MAoyoBWfnzHFtvsGwD/npDBEFB8
7JP9z4tc+LgKlIjg3QWUU52FVm1vEKA8p7jMNLpZmlMkc7pNPjLf
=oPg4
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 updates for 4.12 part1" from Heiko Stübner:
Contains one new board, the Tinkerboard from Asus based on the rk3288,
definitions for the mmc resets in the socs reset controller, sound
support for the Rock2, dma support for mmc controllers on the rk3188
and a led-fix for the MiQi board and and irq-fix for older Cortex-A9 socs.
* tag 'v4.12-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: setup DMA-channels for mmc0 and emmc for rk3188
ARM: dts: rockchip: fix PPI misconfiguration on Cortex-A9 socs
ARM: dts: rockchip: add rk322x dw-mmc resets
ARM: dts: rockchip: add rk3066/rk3188 dw-mmc resets
ARM: dts: rockchip: add rk3036 dw-mmc resets
ARM: dts: rockchip: add rk3288 dw-mmc resets
ARM: dts: rockchip: add dts for RK3288-Tinker board
dt-bindings: add rk3288-based Asus Tinker board
ARM: dts: rockchip: fix the MiQi board's LED definition
ARM: dts: rockchip: Add support for ES8388 to the Radxa Rock 2
- Add the power controller to the DTS.
- Augment the GPIO nodes to also include the Faraday
compatible.
- Add the PCI bus host and config to the Gemini device trees.
-----BEGIN PGP SIGNATURE-----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=AkSm
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "DTS updates for the Gemini on top of the multiplatform base" from Linus Walleij:
- Add the power controller to the DTS.
- Augment the GPIO nodes to also include the Faraday
compatible.
- Add the PCI bus host and config to the Gemini device trees.
* tag 'gemini-dts-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: add PCI to the Gemini device trees
ARM: dts: augment Gemini GPIO nodes
ARM: dts: add power controller to the Gemini DTS
4.12, please pull the following:
- Rafal:
* adds basic support for the Linksys EA9200, Linksys EA6300 V1, Linksys
EA9500, TP-Link Archer C5 V2 which are all based on BCM470x SoCs with
a bunch of BCM43602 radios.
* updates the BCM5301X DTS and DTS include file and moves the serial
console parameters to the DTS include file since all BCM5301X that we have so
far are consistent in using the same UART. He also does the same for the
BCM53573 DTS.
* makes some updates to the Tenda AC9 platform by describing its
PCIe controllers and endpoints in order to be able to represent GPIOs attached
to the on-chip Wi-Fi module. Once done, he adds the 2Ghz LED which is connected
to one of these GPIOs.
* re-licenses the DTS files he created to the ISC license
* removes the use of the non-existend "default-off" LED trigger in the
BCM53573 and BCM5301X DTS files
- Aditya adds missing Netgear R8000 LEDS and keys for WAN status LEDS and brightness
- Jon:
* adds NAND controller Device Tree nodes to the BCM953012K reference board
* converts the BCM5301X SoC to use the recently introduced Broadcom QSPI controller
Device Tree nodes.
* fixes the GIC PPI interrupt flags that the kernel now
reports about.
* adds ARM TWD watchdog entries to the BCM5301X DTS include file
* adds I2C entries to the BCM5301X DTS include files.
* disables i2c by default in the Northstar Plus DTS include file, and
,enables it at the board level instead.
* adds USB (OHCI & EHCI) Device Tree nodes to the Northstar Plus DTS
include files.
- Steven adds the mailbox (PDC) unit and the crytographic unit (SPU) to the
Broadcom Northstar Plus SoC DTS include file. Steven also adds proper ethernet
aliases to the BCM53012HR board since some bootloaders require that for MAC address
patching.
- Eric adds the DSI and its corresponding clock nodes to the BCM283x DTS files
but leaves them disabled by default (overlays should take care of enabling it)
- Boris adds support for HDMI audio and related DMA channels to the BCM283x SoCs
- Gerd adds support for the BCM2835 specific SDHCI controller to the BCM283x SoCs
- Rob fixes the iProc msi-controller name and unit address now that DTC can produce
additional errors
-----BEGIN PGP SIGNATURE-----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=VFXn
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.12/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.12" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree updates for
4.12, please pull the following:
- Rafal:
* adds basic support for the Linksys EA9200, Linksys EA6300 V1, Linksys
EA9500, TP-Link Archer C5 V2 which are all based on BCM470x SoCs with
a bunch of BCM43602 radios.
* updates the BCM5301X DTS and DTS include file and moves the serial
console parameters to the DTS include file since all BCM5301X that we have so
far are consistent in using the same UART. He also does the same for the
BCM53573 DTS.
* makes some updates to the Tenda AC9 platform by describing its
PCIe controllers and endpoints in order to be able to represent GPIOs attached
to the on-chip Wi-Fi module. Once done, he adds the 2Ghz LED which is connected
to one of these GPIOs.
* re-licenses the DTS files he created to the ISC license
* removes the use of the non-existend "default-off" LED trigger in the
BCM53573 and BCM5301X DTS files
- Aditya adds missing Netgear R8000 LEDS and keys for WAN status LEDS and brightness
- Jon:
* adds NAND controller Device Tree nodes to the BCM953012K reference board
* converts the BCM5301X SoC to use the recently introduced Broadcom QSPI controller
Device Tree nodes.
* fixes the GIC PPI interrupt flags that the kernel now
reports about.
* adds ARM TWD watchdog entries to the BCM5301X DTS include file
* adds I2C entries to the BCM5301X DTS include files.
* disables i2c by default in the Northstar Plus DTS include file, and
,enables it at the board level instead.
* adds USB (OHCI & EHCI) Device Tree nodes to the Northstar Plus DTS
include files.
- Steven adds the mailbox (PDC) unit and the crytographic unit (SPU) to the
Broadcom Northstar Plus SoC DTS include file. Steven also adds proper ethernet
aliases to the BCM53012HR board since some bootloaders require that for MAC address
patching.
- Eric adds the DSI and its corresponding clock nodes to the BCM283x DTS files
but leaves them disabled by default (overlays should take care of enabling it)
- Boris adds support for HDMI audio and related DMA channels to the BCM283x SoCs
- Gerd adds support for the BCM2835 specific SDHCI controller to the BCM283x SoCs
- Rob fixes the iProc msi-controller name and unit address now that DTC can produce
additional errors
* tag 'arm-soc/for-4.12/devicetree' of http://github.com/Broadcom/stblinux: (27 commits)
ARM: dts: bcm: fix msi-controller name and unit address
ARM: dts: BCM53573: Specify serial console parameters
ARM: dts: BCM5301X: Specify serial console params in dtsi files
ARM: dts: NSP: Add crypto (SPU) to dtsi
ARM: dts: NSP: Add mailbox (PDC) to NSP
ARM: dts: BCM953012HR: Add ethernet aliases
ARM: dts: BCM5301X: Add support for TP-LINK Archer C5 V2
ARM: dts: NSP: disable i2c DT entry by default
ARM: dts: NSP: Add EHCI/OHCI USB nodes to device tree
ARM: dts: BCM5301X: Add I2C support to the DT
ARM: dts: BCM5301X: Add TWD WD Support to DT
ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
ARM: dts: bcm2835: add sdhost controller to devicetree
ARM: dts: bcm283x: Add HDMI audio related properties
ARM: dts: BCM5301X: Don't use nonexistent "default-off" LED trigger
ARM: dts: BCM53573: Don't use nonexistent "default-off" LED trigger
ARM: dts: BCM5301X: Add missing Netgear R8000 LEDs and Keys
ARM: dts: BCM5301X: Relicense DTS files I created to the ISC
ARM: dts: bcm2835: Add the DSI module nodes and clocks.
ARM: dts: BCM53573: Add Tenda AC9 2 GHz LED
...
- Add node lable for Armada 38x
- Add support for Synology DS116 NAS and Linksys WRT1900ACS
- Update mbus controller description on Armada 38x allowing entering in standby
- Add default trigger for sata led on various linksys boards
- Update newly added armada-xp-98dx3236
- Enable hardware buffer manager support for the devices in the
Linksys WRT AC Serie
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWNVVVyMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71f1XAJ0WIMcrTJPA
uiYAEbN2f+InledW9wCeOD5+hJTSEFFznZSfbzN4Morh0tw=
=+cen
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.12-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt for 4.12 (part 1)" from Gregory CLEMENT:
- Add node lable for Armada 38x
- Add support for Synology DS116 NAS and Linksys WRT1900ACS
- Update mbus controller description on Armada 38x allowing entering in standby
- Add default trigger for sata led on various linksys boards
- Update newly added armada-xp-98dx3236
- Enable hardware buffer manager support for the devices in the
Linksys WRT AC Serie
* tag 'mvebu-dt-4.12-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: mvebu: linksys: enable buffer manager support
ARM: dts: mvebu: remove unnecessary PCI range from 98dx3236
ARM: dts: mvebu: Move mv98dx3236 clock bindings
ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236
ARM: dts: armada-xp-98dx3236: combine dfx server nodes
ARM: dts: armada: Add default trigger for sata led
ARM: dts: armada-38x: Adjust mbus controller description on Armada 38x
ARM: dts: armada-385: add support for the Linksys WRT1900ACS (Shelby)
ARM: dts: armada-385-synology-ds116: add support for Synology DS116 NAS
ARM: dts: armada-38x add node labels
Video display on DA850 along with some
whitespace clean-up.
Also, enables sound and ADC support on
Lego EV3.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DFR4
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.12/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
Pull "DaVinci DT updates for v4.12" from Sekhar Nori:
DaVinci device tree updates to enable
Video display on DA850 along with some
whitespace clean-up.
Also, enables sound and ADC support on
Lego EV3.
* tag 'davinci-for-v4.12/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-evm: add the output port to the vpif node
ARM: dts: da850-evm: add IO expander node on UI card
ARM: dts: da850: add vpif video display pins
ARM: dts: da850-evm: fix whitespace errors
ARM: da850-lego-ev3: Add device tree node for sound
ARM: da850-lego-ev3: Add device tree node for A/DC
The Moxa ART GPIO is a Faraday FTGPIO010. Augment the DTS node
to indicate both compatible values for the SoC and the IP part.
Also increase the register range to 0x100, it has at least 0x48
bytes of registers, and a few extra will not hurt.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the new hdmi phandle to exynos4.dtsi. This phandle is needed by the
s5p-cec driver to initialize the CEC notifier framework.
Tested with my Odroid U3.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Keep the clearfog DTS file ordered alphabetically - Florian placed the
MDIO entry after pinctrl, which mis-orders the file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This moves the spi0_cs3_pin pinconf node from the LEGO EV3 file to the
common DA850 include file. This node is applicable to any board, and
therefore belongs in the common file.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The two st231-rproc nodes have the same name; Due to that it was
impossible to distinguish them in remoteproc sysfs and debugfs
interface.
This patch provides them a name related to their functionality.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
The display backend on sun5i shares the same interrupt line as the
display frontend. Add it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the RPM Clock Controller DT node for msm8974-based platforms, so that
drivers can use the clocks provided by the RPM processor.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The DTS referred to SDC5 when it meant SDC1.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
To make the picture complete, add DTS entries also for the
second and fourth MMC/SD blocks on the MSM8660. SDC2 is
an 8-bit interface and SDC4 is a 4-bit interface.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Without this patch (and with CONFIG_QCOM_ADSP_PIL), I get this error:
[ 0.711529] qcom_adsp_pil adsp-pil: failed to get xo clock
[ 0.711540] remoteproc remoteproc0: releasing adsp-pil
With this patch, adsp-pil can initialize correctly.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add initial set of CoreSight components found on Qualcomm
msm8974 and apq8074 based platforms, including the APQ8074
Dragonboard board.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Rock 2 square board has a USB -> SATA converter hooked up to its usb
host1 connection. Enable the usb controller and always turn on the power
on the 5V sata power connector (controlled by gpio).
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
All three devices provide GPIO based LEDs named power,
wlan and app.
Place LEDs definition into a separate dtsi file as not all
devices including am335x-baltos.dtsi have the same LED layout.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's a typo, it should be GPIO176 and not GPIO106.
And it seems I messed up the regulators at some point while trying
to figure out what devices the regulators are used. The correct
regulator for MMC1 is vwlan2.
Fixes: 0d4cb3ccee ("ARM: dts: Configure regulators for droid 4")
Reported-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The second channel of the display unit uses a different module clock
than the first channel.
Fixes: 84e734f497 ("ARM: dts: silk: add DU DT support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The second channel of the display unit uses a different module clock
than the first channel.
Fixes: 876e7fb9f4 ("ARM: shmobile: r8a7794: alt: Enable VGA port")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The second channel of the display unit uses a different module clock
than the first channel.
Fixes: 46c4f13d04 ("ARM: shmobile: r8a7794: Add DU node to device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the missing module clock for the second channel of the display unit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
An alias name should have an index number even when it is the only of its type.
This allows U-Boot to add the local-mac-address property. Otherwise U-Boot
skips the alias.
Fixes: 6a93792774 ("ARM: bcm2835: dt: Add the ethernet to the device trees")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Eric Anholt <eric@anholt.net>
According to the BCM2835 ARM Peripherals document uart1 doesn't map to pins
36-39, but uart0 does.
Also, split into separate Rx/Tx and CST/RTS groups to match other uart nodes.
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
According to the BCM2835 ARM Peripherals document i2c0 doesn't map to pins 32,
34 but to 28, 29.
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
Downstream kernel uses pins 32, 33 as UART0 (PL011) Rx/Tx to communicate with
the Bluetooth chip. So ALT3 of these pins is most likely not CTS/RTS. Change
the node name to reflect that. This matches section 6.2 "Alternative Function
Assignments" in the BCM2835 ARM Peripherals document.
With this change in place, adding
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
status = "okay";
};
to bcm2837-rpi-3-b.dts does the right thing on my Raspberry Pi 3.
Pins 30, 31 are CTS/RTS of UART0 in alternate function 3. Rename uart0_gpio30
as well.
While at it, fix a little typo in a nearby comment.
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
mmc2 used for wl12xx was missing the keep-power-in suspend
parameter. As a result the board couldn't reach suspend state.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Orange Pi Zero board features a USB OTG port, which has a ID pin, and
can be used to power up the board. However, even if the board is powered
via +5V pin in GPIO/expansion headers, the VBUS in the OTG port cannot
be powered up, thus it's impossible to use it in host mode with simple
OTG cables.
Add support for it in peripheral mode.
If someone really want to use it in host mode, the mode of PHY can be
switch via sysfs, then use a powered USB OTG cable or powered USB HUB to
power up external USB devices.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orange Pi One features a MicroUSB port that can work in both host mode
and peripheral mode.
When in host mode, its VBUS is controlled via a GPIO; when in peripheral
mode, its VBUS cannot be used to power up the board.
Add support for this port.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner H3/H5 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
or MUSB controller.
Add device nodes for these controllers.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc and gic, as well as pio and ccu's
compatible, and make drop of skeleton into a seperated patch]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the datasheets provided by Allwinner, both Allwinner H3 and
H5 use GIC-400 as their interrupt controller.
For better device tree reusing, correct the GIC compatible in H3 DTSI to
"arm,gic-400", thus this node can be reused in H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
After converting to generic pinconf binding, pinctrl-a10.h is now not
used at all.
Drop its inclusion for H3 DTSI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The skeleton.dtsi file is now deprecated, and do not exist in ARM64
environment.
Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
chip, drop skeleton.dtsi inclusion now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit makes use of the axp209.dtsi file to define the
AXP209 PMIC. While here, define the rails that are enabled on
this board.
Tested checking the regulator voltage varies according to the
CPU frequency.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SinA31s has a coaxial SPDIF output. Enable it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the cpu-supply DT property to the cpu0 DT node needed by
the board to adapt the regulator voltage depending on the currently used
OPP.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds almost all operating points allowed for the A33 as defined by
fex files available at:
https://github.com/linux-sunxi/sunxi-boards/tree/master/sys_config/a33
There are more possible frequencies in this patch than there are in the
fex files because the fex files only give an interval of possible
frequencies for a given voltage. All supported frequencies are defined
in the original driver code in Allwinner vendor tree.
There are two missing frequencies though: 1104MHz and 1200MHz which
require the CPU to have 1.32V supplied, which is higher than the default
voltage.
Without all A33 boards defining the CPU regulator, we cannot have these
two frequencies as it would cause the CPU to try to run a higher
frequency without "overvolting" which is very likely to crash the CPU.
Therefore, these two frequencies must be enabled on a per-board basis.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The NextThing Co. CHIP has an AXP209 PMIC and can be power-supplied by
ACIN via the CHG-IN pin.
This enables the ACIN power supply subnode in the DT.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sinlinx SinA33 has an AXP223 PMIC and an ACIN connector, thus, we
enable the ACIN power supply in its Device Tree.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The X-Powers AXP22X PMIC exposes the status of AC power supply.
This adds the AC power supply subnode for the AXP22X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The X-Powers AXP20X PMIC exposes the status of AC power supply, the
current current and voltage supplied to the board by the AC power
supply.
This adds the AC power supply subnode for AXP20X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The old sunxi specific pinctrl bindings are deprecated, in favor of
the new generic pinconf bindings. Also, we are moving towards handling
GPIO pinmux settings that don't require extra bias or drive strength
settings to use the GPIO bindings only.
This patch removes the last instance of the sunxi specific pinctrl
bindings that use the pinctrl header by dropping the pinmux setting
for the audio codec's PA (external amplifier) control GPIO. The pin
is pulled down externally.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PCIe bridges should have a node name of 'pcie'.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
The Cortina Gemini has an internal PCI root bus, add this to
the device tree, and add interrupt mapping (swizzling) to the
relevant systems device trees.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Feng-Hsin Chiang <john453@faraday-tech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Raspberry Pi, and nodes to describe the DSI and SDHOST hardware
modules (which are still disabled by default).
-----BEGIN PGP SIGNATURE-----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=bTSQ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=cLA3
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-dt-next-2017-03-21' into devicetree/next
This pull request brings in the DT nodes for enabling HDMI audio on
Raspberry Pi, and nodes to describe the DSI and SDHOST hardware
modules (which are still disabled by default).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
please pull the following:
- Jon fixes a reboot issue on most Northstar Plus platforms by adding the
"open-source" property to the "gpio-restart" Device Tree nodes
-----BEGIN PGP SIGNATURE-----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=CKev
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.11/devicetree-fixes-2' of http://github.com/Broadcom/stblinux into fixes
Pull "Broadcom arm Device Tree fixes for 4.11 (part 2)" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.11,
please pull the following:
- Jon fixes a reboot issue on most Northstar Plus platforms by adding the
"open-source" property to the "gpio-restart" Device Tree nodes
* tag 'arm-soc/for-4.11/devicetree-fixes-2' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: GPIO reboot open-source
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for STM32H743 MCU and his eval board.
The STMicrolectornics's STM32H743 MCU is based on Cortex-M7 core
running up to @400MHz with 2MB internal flash and 1MB internal RAM.
For more details see:
Documentation/arm/stm32/stm32h743-overview.txt
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Add pinmux for rx,tx,cts and rts lines of uart0. This will enable uart0
to use hardware flow control.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable support for W25Q64CVSSIG which is a Winbond 64 Mbit SPI NOR.
At boot you will see the following message:
m25p80 spi1.0: found s25fl064k, expected w25q64
This is because the JEDEC ID for this chip is the same as s25fl064k.
However, this should be harmless since both chips are essentially the
same.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in dra7.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.
As we now need to define voltage ranges for each OPP, we define the
minimum and maximum voltage to match the ranges possible for AVS class0
voltage as defined by the DRA7/AM57 Data Manual, with the exception of
using a range for OPP_OD based on historical data to ensure that SoCs
from older lots still continue to boot, even though more optimal voltages
are now the standard. Once an AVS Class0 driver is in place it will be
possible for these OPP voltages to be adjusted to any voltage within the
provided range.
Information from SPRS953, Revised December 2015.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The operatings-points-v2 table for am4372 was merged before any user of
it was present in the kernel and before the binding had been finalized.
The new ti-cpufreq driver and binding expects the platform specific
properties to be part of the operating-points-v2 table rather than the
cpu node so let's move them there as the only user is the ti-cpufreq
driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although all PG2.0 silicon may not support 1GHz OPP for the MPU, older
Beaglebone Blacks may have PG2.0 silicon populated and these particular
parts are guaranteed to support the OPP, so enable it for PG2.0 on
am335x-boneblack only.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in am33xx.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.
Information from AM335x Data Manual, SPRS717i, Revised December 2015,
Table 5-7.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the SATA controller node to the dm8168-evm device tree.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This board has an external oscillator supplying the reference clock
signal for SATA. Its rate is fixed at 100Mhz. Add a corresponding
device tree node.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though cpsw doesn't support EEE feature, Atheros 8035 provides
automatic EEE support that is enabled by default. This causes
occasional link drops when link partner also announces EEE support.
These link drops occur on both 100Mbit/s and 1000Mbit/s speeds.
So disable EEE advertising completely.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The manufacturing information is stored in the EEPROM. This chip
is an AT24C64 not not (nor has it ever been) 24C02. This patch will
correctly address the EEPROM to read the entire contents and not just
256 bytes (of 0xff).
Fixes: 5e3447a29a ("ARM: dts: LogicPD Torpedo: Add AT24 EEPROM Support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch set HSE_RTC clock frequency to 1 MHz, as the clock supplied to
the RTC must be 1 MHz.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch lists STM32F7's RCC numeric constants.
It will be used by clock and reset drivers, and DT bindings.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch enables clocks for STM32F746 MCU.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Add appropriate properties to devices in the Linksys WRT AC Series for the
mvneta driver to use hardware buffer management.
Also update "soc" ranges property and set the status of bm and bm-bppi
to "okay" (SRAM).
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[adapted rk1108 dtsi to keep bisectability]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Nokia N950 and N9 have a wl1271 (with nokia bootloader) bluetooth
module connected to second UART.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add bcm2048 node and its system clock to the N900 device tree file.
Apart from that a reference to the new clock has been added to
wl1251 (which uses it, too).
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The unit address for the msi controller is not valid as there is no reg
property, so remove it. Also, msi-controller is the preferred node name.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[include rename in rk1108.dtsi to prevent compile errors]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds baud rate, parity & number of data bits. It's required to get
serial working correctly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
So far every Northstar device we have seen was using the same serial
console params (115200n8). It probably make the most sense to put it in
some proper dtsi files instead of repeating over and over for every
single device. As different boards may use different bootloaders it
seems the safest idea is to use board specific dtsi files.
Just in case some vendor decides to use different UART (parameters) this
can be always easily overwritten.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Droid 4 has two modems, mdm6600 and w3glte. Both are on the HCI USB
controller.
Let's add a configuration for the HCI so the modems can be enabled.
Note that the modems still need additional GPIO based configuration.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
[tony@atomide.com: left out url]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LCD panel on droid 4 is a command mode LCD. The binding follows
the standard omapdrm binding and the changes needed for omapdrm command
mode panels are posted separately.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can get HDMI working as long as the 5V regulator is on. There is
probably an encoder chip there too, but so far no idea what it might be.
Let's keep the 5V HDMI regulator always enabled for now as otherwise we
cannot detect the monitor properly.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add tmp105 sensor for droid 4. This can be used with modprobe
lm75.ko and running sensors from lm-sensors package. Note that
the lm75.c driver does not yet support alert interrupt but
droid 4 seems to be wired for it.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Droid 4 has a GPIO line that we can use with CONFIG_POWER_RESET_GPIO.
It is probably connected to the CPCAP PMIC, and seems to power down
the whole device taking power consumption to zero based on what
I measured.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TI LMU driver has not yet been merged, but the device
tree binding for TI LMU drivers has been acked already
earlier by Rob Herring <robh+dt@kernel.org>. So it should
be safe to apply to cut down the number of pending patches.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit enable DMA-based transfers for SD/eMMC card adapters
and reduce number of interrupts produced by SD-card/eMMC-card
adapters.
Sometimes interrupts from SD-card/eMMC-card adapters running in
PIO mode blocks execution of hrtimers and I2S DMA callbacks for
a long periods (100 ms or more).
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
[moved dma properties to rk3xxx.dtsi and added sdio dma]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The binding should state "cortina,gemini-gpio", "faraday,ftgpio010"
stating the full name of the IP part.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to [0] pointed out by Marc Zyngier in a report about a
similar error message, PPIs 11 and 13 are edge triggered on
Cortex-A9 socs including the rk3066 and rk3188 which currently
mark them as level triggered.
Until some time ago the gic did not care but commit 992345a58e
("irqchip/gic: WARN if setting the interrupt type for a PPI fails")
introduced a warning for that case.
Fix the warning on these socs by describing the interrupts correctly
and also using the binding constants for easier reading in the future.
[0] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0407f/CCHEIGIC.html
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The OPP are declared as shared but no operating points are declared for
cpu1, 2 and 3. Thus, the following error happens during the boot:
cpu cpu1: dev_pm_opp_of_get_sharing_cpus: Couldn't find tcpu_dev node.
This patch applies the operating points to each cpu of the A33.
Fixes: 03749eb88e ("ARM: dts: sun8i: add opp-v2 table for A33")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cleanup:
* Drop superfluous status update for frequency override on various boards
* Always use status "okay" to enable devices on porger board
* Add INTC-SYS clock to device tree of various SoCs
* Tidyup Audio-DMAC channel for DVC on r8a779[013] SoCs
* Remove unit-address and reg from integrated cache on various SoCs
* Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS
* Fix SCIFB0 dmas indentation on r8a774[35] SoCs
Enhancements:
* Add watchdog timer to r7s72100 SoC
* Update sdhi clock bindings on r7s72100 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cA1
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.12
Cleanup:
* Drop superfluous status update for frequency override on various boards
* Always use status "okay" to enable devices on porger board
* Add INTC-SYS clock to device tree of various SoCs
* Tidyup Audio-DMAC channel for DVC on r8a779[013] SoCs
* Remove unit-address and reg from integrated cache on various SoCs
* Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS
* Fix SCIFB0 dmas indentation on r8a774[35] SoCs
Enhancements:
* Add watchdog timer to r7s72100 SoC
* Update sdhi clock bindings on r7s72100 SoC
* tag 'renesas-dt-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
ARM: dts: silk: Drop superfluous status update for frequency override
ARM: dts: alt: Drop superfluous status update for frequency override
ARM: dts: gose: Drop superfluous status update for frequency override
ARM: dts: porter: Drop superfluous status update for frequency override
ARM: dts: koelsch: Drop superfluous status updates for frequency overrides
ARM: dts: lager: Drop superfluous status update for frequency override
ARM: dts: marzen: Drop superfluous status update for frequency override
ARM: dts: bockw: Drop superfluous status update for frequency override
ARM: dts: porter: Always use status "okay" to enable devices
ARM: dts: r8a7793: Add INTC-SYS clock to device tree
ARM: dts: r8a7793: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7791: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7794: Add INTC-SYS clock to device tree
ARM: dts: r8a7792: Add INTC-SYS clock to device tree
ARM: dts: r8a7791: Add INTC-SYS clock to device tree
ARM: dts: r8a7790: Add INTC-SYS clock to device tree
ARM: dts: r8a73a4: Add INTC-SYS clock to device tree
ARM: dts: r7s72100: Add watchdog timer
ARM: dts: r8a7790: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7794: Remove unit-address and reg from integrated cache
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix USB host for sama5d2
- Fix cpuidle on sama5
-----BEGIN PGP SIGNATURE-----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=XXBm
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into fixes
Fixes for 4.11:
- Fix USB host for sama5d2
- Fix cpuidle on sama5
* tag 'at91-ab-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: pm: cpu_idle: switch DDR to power-down mode
Revert "ARM: at91/dt: sama5d2: Use new compatible for ohci node"
Signed-off-by: Olof Johansson <olof@lixom.net>
A bunch of device tree fixes for various boards / SoCs.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJYz6jpAAoJEBx+YmzsjxAg2agP/RVoD/o3JctGCUfqgRog5kCJ
A8wUi63bAG52XVccYm2NFdEMhYoGpnuiljIytSW6v0JewzRblnpJHnJu+W60t+2p
x1dcqwPCfObRAkPZLaGHIJmsJuJcDa3hD1s6kqxNYqnaqjTKldbnuDycbV2IPI1i
0M6p4yVVWaZAVSdgew0hwUTx2C3JKaZNRfWFddVl8lf6iBRBCWJq7POKH1wttdsz
Da5wzHtLnMHk5EO9G6i/VDQAoc7EUCJeQ84/ZDgFREfbRJokefWvtz+LEWh9KYQK
fK5O8rsNrJTcgCHERL61fz4hbc8knWP2WvxbQ7wVNXTc9R3VZW9lBpovxgHzjXc+
8qY5mMGmU9jr4Xli/3q5fS/b7Tw2w8DT043vKhg7oFrpeEwh5a+hfWPjqcRPObAi
XxxN9ixnfbV3CC0DMIdk+ghu+FxOzUVa8Dmg7P0rrZ5j5iFBbBIWyTLqdsA/t5Hz
bNOW4XSHlja8Xqkpr4Ebp4nxUbTxVNdWLwann5w5Ty5w7RRsN60iZJdwl8VZTPHp
OgEuIbZcKTBIBAJNINgeTUNhBDspL9MunteTXKjvWr8EwayuU2/kcWCieyb9ar8D
3Bf8WghlM3roiHDqdfaAxxMD56nVGhMgwVa6I42uvCFQz5/xrtF9cMLelOuR0NPX
cNirP1PVVeEjgRIiSO1F
=fo5j
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.11
A bunch of device tree fixes for various boards / SoCs.
* tag 'sunxi-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sun8i: a23/a33: drop bl_en_pin GPIO pinmux in reference design DTSI
ARM: dts: sun7i: lamobo-r1: Fix CPU port RGMII settings
ARM: sun8i: Fix the mali clock rate
Signed-off-by: Olof Johansson <olof@lixom.net>
- A fix to reboot hang seen on imx6sx-udoo-neo board, by removing
arm-supply and soc-supply and using LDO enabled mode.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYz5T0AAoJEFBXWFqHsHzOiUwH/1S1b6Si8fbG0g11BQm+2N0u
mHf3Z41f+F81xuFFt/6ZX5ICiOXDlAdcga3QXUCNCWfYnFLJyDSoF6Z1JSUkGeEa
kVCmi+WWUOYtyU7QYfaBzPtZqqUurqwBu8WwOO/IW81yKpNMNflATKYreutki2oI
z3BW3WGlOEJXIJeyea3EjTClQLhP0qdEn08StneHUdA+YS9nd6/jreHhta4r7gQs
Z4B2yBap7P4a5glOzCafuIAdpPscKS096ND1k3APsiJPGaNjYtxhig5MGo89LK7e
JNfw1KroAmifGVmrgDVwKI3MFLrvSh74phFXwnIAX5iK2U2wB/fiMQjVKmvY9tw=
=NSw6
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.11:
- A fix to reboot hang seen on imx6sx-udoo-neo board, by removing
arm-supply and soc-supply and using LDO enabled mode.
* tag 'imx-fixes-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx-udoo-neo: Fix reboot hang
Signed-off-by: Olof Johansson <olof@lixom.net>
The moxart interrupt line flags were not respected in previous
driver: instead of assigning them per-consumer, a fixes mask
was set in the controller.
With the migration to a standard Faraday driver we need to
set up and handle the consumer flags correctly. Also remove
the Moxart-specific flags when switching to using real consumer
flags.
Extend the register window to 0x100 bytes as we may have a few
more registers in there and it doesn't hurt.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Allow including of dtsi files in an architecture-independent manner.
Some dtsi files may be shared between architectures and one suggestion
was to have symlinks and let these includes get accessed via a
#include <arm64/foo.dtsi>
So add the necessary symlinks for arm32.
Suggested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. The interrupt has to be cleared, because otherwise
system enters infinite interrupt handling loop.
Use a samsung,s3c6410-wdt compatible to select appropriate quirk for
clearing the watchdog interrupt.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. The interrupt has to be cleared, because otherwise
system enters infinite interrupt handling loop.
Use a samsung,s3c6410-wdt compatible to select appropriate quirk for
clearing the watchdog interrupt.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. The interrupt has to be cleared, because otherwise
system enters infinite interrupt handling loop.
Use a samsung,s3c6410-wdt compatible to select appropriate quirk for
clearing the watchdog interrupt.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The highest supported frequency (1.2GHz) requires to "overvolt" the CPU.
However, some boards still do not have the cpu-supply DT property in the
cpu DT node which means that the CPU will always run with the same input
voltage but try to run at 1.2GHz frequency. This is the source of
(experienced) CPU crashes.
Remove the OPP which requires overvolting the CPU until all boards have
a cpu-supply property.
Fixes: 03749eb88e ("ARM: dts: sun8i: add opp-v2 table for A33")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The digital AIF interfaces has been renamed in the sun8i audio codec
driver so the audio-routing in the device tree must be renamed too.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add properties to describe the reset topology for on-SoC devices:
- Add the "#reset-cells" property to the CPG/MSSR device node,
- Add resets and reset-names properties to the various device nodes.
This allows to reset SoC devices using the Reset Controller API.
Note that all resets added match the corresponding module clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add properties to describe the reset topology for on-SoC devices:
- Add the "#reset-cells" property to the CPG/MSSR device node,
- Add resets and reset-names properties to the various device nodes.
This allows to reset SoC devices using the Reset Controller API.
Note that all resets added match the corresponding module clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The bl_en_pin GPIO pinmux is configured as "gpio_in", which makes it
conflicts with the real GPIO usage (out), and makes the backlight not
usable.
Drop the GPIO pinmux for it, thus this GPIO can be correctly used.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CPU port of the BCM53125 is configured with RGMII (no delays) but
this should actually be RGMII with transmit delay (rgmii-txid) because
STMMAC takes care of inserting the transmitter delay. This fixes
occasional packet loss encountered.
Fixes: d7b9eaff5f ("ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the Gemini power controller to the SoC DTSI
file.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds crypto hardware (SPU) to Northstar Plus device tree file.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adds mailbox / PDC to NSP device tree. Needs new compatibility string
to differentiate from NS2 version.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adding ethernet aliases. These are used, for example, by bootloaders,
to modify the MAC addresses in the device tree.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This is BCM47081A0 based home router with BCM43217 and BCM4352 wireless
chipsets.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c device tree entry should be disabled by default to match the
current convention in other device tree files. Similarily, enable it on
the XMC board, where it is being used.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the EHCI and OHCI entries to the Northstar Plus device tree files.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add I2C support to the bcm5301x Device Tree. Since no driver changes
are needed to enable this hardware, only the device tree changes are
required to make this functional.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for the ARM TWD Watchdog to the bcm5301x device tree. The
ARM TWD timer allocated the register space for the WDT, so this patch
necessitated shrinking that. Also, the GIC masks were added for these.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
GIC_PPI flags were misconfigured for the timers, resulting in errors
like:
[ 0.000000] GIC: PPI11 is secure or misconfigured
Changing them to being edge triggered corrects the issue
Suggested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add OneNAND node for IGEP and leave it disabled by default. It is up
to bootloader to enable proper node. Timing just works, but values are
copied over from N900 as I was unable to find chip datasheet.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Note that early-bresp-disable and full-line-zero-disable are required
because the sideband signals between the CPU and L2C were not connected
in this SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The libgpio code pre-sets the GPIO values for the gpio-reset in the
device tree. This results in the device being reset during bringup.
To prevent this pre-setting, use the "open-source" flag in the device
tree.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: b1aaf88 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file")
Fixes: 10baed1 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file")
Fixes: 088e3148 ("ARM: dts: NSP: Add new DT file for bcm958522er")
Fixes: e3227c1 ("ARM: dts: NSP: Add new DT file for bcm958525er")
Fixes: 2f8bc00 ("ARM: dts: NSP: Add new DT file for bcm958622hr")
Fixes: d454c37 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Fixes: f27eacf ("ARM: dts: NSP: Add new DT file for bcm988312hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the dmas and dma-names properties to support HDMI audio.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the Altera Arria10 System Resource Reset Controller to the MFD
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2 change commit header to ARM: dts: socfpga.
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3228/rk3229.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3066/rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3036.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3288.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
The best place to register the CPU cooling device is from the cpufreq
driver as we would know if all the resources are already available or
not. That's what is done for the cpufreq-dt.c driver as well.
The cpu-cooling driver for dbx500 platform was just (un)registering
with the thermal framework and that can be handled easily by the cpufreq
driver as well and in proper sequence as well.
Get rid of the cooling driver and its its users and manage everything
from the cpufreq driver instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix smartreflex platform data regression where I accidentally
removed legacy platform data still in use
- Fix hypervisor mode for thumb2 kernel
- Fix misplaced tpic2810 to move it to right bus
- Enable INPUT_MOUSEDEV as a loadable module have mice working
- Fix use of gpio-key,wakeup and use wakeup-source instead as
this accidentally sneaked in during the merge window
- Fix error handling for onenand to properly return error
- Remove legacy gpmc-nand.c that's now dead code, this
also removes dependency to the MTD tree for further driver
changes
- Fix device node reference count errors for omap3 and
related to it also release device nodes after no longer
needed
-----BEGIN PGP SIGNATURE-----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=svZk
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.11/fixes-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.11-rc cycle:
- Fix smartreflex platform data regression where I accidentally
removed legacy platform data still in use
- Fix hypervisor mode for thumb2 kernel
- Fix misplaced tpic2810 to move it to right bus
- Enable INPUT_MOUSEDEV as a loadable module have mice working
- Fix use of gpio-key,wakeup and use wakeup-source instead as
this accidentally sneaked in during the merge window
- Fix error handling for onenand to properly return error
- Remove legacy gpmc-nand.c that's now dead code, this
also removes dependency to the MTD tree for further driver
changes
- Fix device node reference count errors for omap3 and
related to it also release device nodes after no longer
needed
* tag 'omap-for-v4.11/fixes-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Release device node after it is no longer needed.
ARM: OMAP2+: Fix device node reference counts
ARM: OMAP2+: Remove legacy gpmc-nand.c
ARM: OMAP2+: gpmc-onenand: propagate error on initialization failure
ARM: dts: am335x-pcm953: Fix legacy wakeup source binding
ARM: omap2plus_defconfig: Enable INPUT_MOUSEDEV as loadable modules
ARM: dts: am57xx-idk: tpic2810 is on I2C bus, not SPI
ARM: OMAP5 / DRA7: Fix HYP mode boot for thumb2 build
ARM: OMAP3: Fix smartreflex platform data regression
Signed-off-by: Olof Johansson <olof@lixom.net>
please pull the following:
- Jon fixes the UART output on the Broadcom bcm953012k reference board by
using the proper clock reference instead of hard-coding the baud rate
- Jon also fixes the memory map on the bcm953012k reference board by using
the appropriate physical RAM start address
- Jon finally fixes the interrupt type for the Cortex A9 global and local
timers found in the BCM5301X SoC (Norsthar).
-----BEGIN PGP SIGNATURE-----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=0Qzy
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.11/devicetree-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for 4.11,
please pull the following:
- Jon fixes the UART output on the Broadcom bcm953012k reference board by
using the proper clock reference instead of hard-coding the baud rate
- Jon also fixes the memory map on the bcm953012k reference board by using
the appropriate physical RAM start address
- Jon finally fixes the interrupt type for the Cortex A9 global and local
timers found in the BCM5301X SoC (Norsthar).
* tag 'arm-soc/for-4.11/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
ARM: dts: BCM5301X: Fix memory start address
ARM: dts: BCM5301X: Fix UARTs on bcm953012k
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the AB8500 clocks to the device tree using the new
bindings from the clk subsystem, making audio work again.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Watchdog module does not have external dependencies so it can be safely
enabled in exynos4.dtsi thus making it available for all Exynos4-based
boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Watchdog module does not have external dependencies so it can be safely
enabled in s3c64xx.dtsi thus making it available for all S3C64xx-based
boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
The Exynos4412 has the same watchdog as newer SoCs (e.g. Exynos5250).
Just like the others, for working it requires additional steps in Power
Management Unit: unmasking the reset request and enabling the system
reset. Without these additional steps in PMU, the watchdog will not be
able to reset the system on expiration event.
Change the compatible of Exynos4412 watchdog device node to
samsung,exynos5250-wdt which includes the additional PMU steps.
This will also fix infinite watchdog interrupt in soft mode (lack of
interrupt clear) because it is also included in samsung,exynos5250-wdt.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
The scif_clk device node is already enabled in r8a7794.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7794.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7793.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The pcie_bus_clk device node is already enabled in r8a7791.dtsi, so
there is no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk and pcie_bus_clk device nodes are already enabled in
r8a7791.dtsi, so there is no need to update their statuses again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7790.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7779.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7778.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
While status "ok" does work, the canonical form is "okay", so update the
few places that used the former.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-wbd222.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference their
parent GPIO.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-wbd111.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference their
parent GPIO.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-rut1xx.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference their
parent GPIO.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-nas4220b.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference &gpio1.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a device tree for the Gemini SoC and the ITian
Square One SQ201 board that has been my testing target
for Gemini device tree support.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The eMMC devices on UniPhier boards are generally used in the 8-bit
mode. So, DAT4-7 pins should be controlled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These UniPhier DT files are fine as long as they are compiled in the
Linux build system. It is true that Linux is the biggest user of
DT, but DT is project neutral from its concept. DT files are often
re-used for other projects. Especially for the UniPhier platform,
these DT files are re-used for U-Boot as well.
If I feed these DT files to the FDTGREP tool in U-Boot, it complains
about the node order.
FDTGREP spl/u-boot-spl.dtb
Error at 'fdt_find_regions': FDT_ERR_BADLAYOUT
/aliases node must come before all other nodes
Given that DT is not very sensitive to the order of nodes, this is a
problem of FDTGREP. I filed a bug report a year ago, but it has not
been fixed yet.
Differentiating DT is painful. So, I am up-streaming the requirement
from the down-stream project.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on audio data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on audio data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock and the C4 power domain,
so it can be power managed using that clock in the future.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add watchdog timer support for RZ/A1.
For the RZ/A1, the only way to do a reset is to overflow the WDT, so this
is useful even if you don't need the watchdog functionality.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Such a trigger doesn't exist in Linux and is not needed as LED is being
turned off by default. This could cause errors in LEDs core code when
trying to set default trigger.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Such a trigger doesn't exist in Linux and is not needed as LED is being
turned off by default. This could cause errors in LEDs core code when
trying to set default trigger.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch updates the Duckbill device tree and synchronize it with
the vendor distributed file. The changes in mostly pin-muxing stuff,
but also some minor fixes. In detail:
- enable SPI pins
- enable I2C pins
- enable UART pins
- enable LRADC pin
- adjust USB DR mode
- add default triggers for LEDs
- get rid of regulators simple-bus container
- adjust phy reset duration
According to phy datasheet, 25ms are sufficient. This also reduces
the time to boot the system.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
