Newer SoCs have two different AHB interconnect. The AHB 32 bits Matrix
interconnect (h32mx) has a clock that can be setup at the half of the h64mx
clock (which is mck). The h32mx clock can not exceed 90 MHz.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The platform is end of life/support and should not clutter
the mach-at91 directory with non-DT files. It is therefore
removed.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As Acme Systems Fox G20 is available in Device Tree flavor and that we plan to
remove all the board files soon, we can remove this one without problem.
If you use this board, please use a DT-enabled at91sam9g20 kernel with
at91-foxg20.dts.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Sergio Tanzilli <tanzilli@acmesystems.it>
Now that we don't depend on anyting in the mach-at91 directory, we can just
move the driver to where it belongs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Conflicts:
arch/arm/mach-at91/Kconfig
arch/arm/mach-at91/Makefile
This allows to remove the dependency of the timer driver on mach/hardware.h and
having an hardcoded interrupt number in the driver itself.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Actually register clocks from device tree when using the common clock
framework.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: add at91 to function name]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The SAMA5 and SAM9x5 series both have drive strength
options for the PIOs. This patch adds the ability to set
one of three hardware options for drive strengths of low,
medium or high for the each pin. The actual current output
of the chip based on the setting is defined in the datasheets
and varies per pins separate from banks and with supply
voltage.
This patch adds three new dt-bindings that allow setting the
strength when configuring pins. By default, no change will
be made to the drive strength of a pin from its reset value.
Due to the difference between the register addresses of the
SAMA5 and SAM9x5 series, a new sama5d3-pinctrl id was added.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have the init_time callback in the at91_init_soc structure, convert
all the boards and SoC to this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Introduce an init_time callback to the at91_init_soc structure to be able to
tweak the init_time machine callback on a per-soc basis, instead of having to
rely on a global one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Conflicts:
arch/arm/mach-at91/setup.c
The timer driver is using some global variables to define some variables it has
to use in most of its functions, like the base address.
Use some container_of calls to have a single dynamic (and local) variable to
hold this content.
The only exception is in the !DT case, where the call chain to
at91sam926x_ioremap_pit and then at91sam926x_pit_init as init_time makes it
hard for the moment to pass the physical address of the timer.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
We can use the generic request_irq now to register a timer interrupt handler,
instead of the more complex setup_irq.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
All the panic messages hardcode the same prefix. Define the pr_fmt macro to
unify its definition.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The current probe code is, whenever it fails to retrieve a resource, either
panicing, silently returning, or returning and displaying an error.
Make the code consistent by always panicing whenever it fails to grab any
resource.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The current AT91 DT boards have a completely generic init_time definition.
Remove them from the machine declaration.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Conflicts:
arch/arm/mach-at91/board-dt-sam9.c
arch/arm/mach-at91/board-dt-sama5.c
The PIT timer driver until now had a single probe function, disregarding wether
it was probed through DT or in the old-style way. This code later on was
calling some DT function to retrieve the proper values for its base address,
interrupts and clocks.
While this was working, it was preventing the usage of CLOCKSOURCE_OF_DECLARE,
and the two different probe path were not as clearly separated as they could
be.
Rework the probe path to take this into account, and switch to
CLOCKSOURCE_OF_DECLARE.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Until now, the machines, even when CONFIG_OF was enabled, were calling
at91sam926x_ioremap_pit to try to map the PIT address using the defined
physical address.
Obviously, with DT, it's not appropriate anymore, and some code was added to
the function to deal with this case.
Unfortunately, this code was conditionned on CONFIG_OF, which can be enabled,
even though no DT was actually used, which would result in such a case, to this
code being executed, without any reason.
Moreover, the logic that was here before to bail out of the function just check
in the DT to see if the PIT node is there, which is the case in all our DTSI.
All this can be made much more straightforward just by using
of_have_populated_dt to bail out.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Until now, the pit_cycle computation was dividing the rate by HZ, rounding to
the closest integer, but without using the appropriate macro.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The generic.h header file doesn't have any safe guards against multiple
inclusion. It only worked so far because all the symbols defined in it were
extern, but this is a rather fragile assumption.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Replace all masks and bits definitions by matching calls to BIT and GENMASK.
While we're at it, also fix a few style issues.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
These board specific delays are now configured through micrel's specific
DT bindings (see Documentation/devicetree/bindings/net/micrel-ksz9021.txt).
Remove this phy fixup registration from sama5 DT machine file to keep it
as generic as possible.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After the for_each_matching_node loop, we end up with a null value for np. Then,
of_match_node() is not matching anything and we can't register the standby
function and "ramc no standby function available" is printed.
Fix that by selecting the first available standby function. For now,
at91_pm_set_standby doesn't support multiple different standby functions and no
existing SoCs have different RAM controllers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
These headers used to provide an "API" to access the rstc and shdwc registers.
Now that no-one uses this API anymore, we can safely remove those.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Now that there's no user left for the global variables holding the reset and
shutdown controllers base address, we can remove these variables and their
associated mapping function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Both the reset and poweroff drivers are now implementing what the
show_reset_status function used to do. Hence, we can remove this rather hackish
function that prevents us from doing further cleanup.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Now that all the SoC have been converted to use the new poweroff driver, we can
remove the poweroff code defined in mach-at91.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Register the poweroff driver in the old-style SoC definition so that the driver
is loaded and provide a shutdown hook.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Now that the poweroff code is a driver of its own, remove the DT probing in
mach-at91 and let the usual DT code do its job.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Now that the transition is over and that we probe our reset driver in every
case, we can remove the legacy code from the machine directory.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Make every board call the register_devices callback so that the devices
declared by the SoC are registered.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Register the reset device in the right SoCs so that the reset driver is
actually probed even in the old-style probing case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Some core devices should be registered by the SoC itself rather than by every
board using this SoC. Introduce a register_devices callback that should be
called during the init_machine in order to do that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Now that the reset code is a driver of its own, just let the usual DT probing
mecanism do its job, and remove the code entirely in this case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Adapt the ramc mapping code to handle multiple ram controllers in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Most of the printed messages are using the "AT91:" prefix in the setup.c file,
but not all of them. Moreover, those who add it hardcode it directly in the
message, while the pr_fmt macro makes it easier for us to support such a case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This tag holds the various new drivers introduced to move code that used to be
in mach-at91 over to the proper frameworks.
These files are the reboot and poweroff code for all AT91 SoCs but the RM9200,
and the ram controller driver is not doing much at the time, except for grabing
the RAM clock in order to leave it always enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YBPz
-----END PGP SIGNATURE-----
Merge tag 'at91-drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux
Pull AT91 reset, poweroff and ram drivers from Maxime Ripard:
"This tag holds the various new drivers introduced to move code that used to be
in mach-at91 over to the proper frameworks.
These files are the reboot and poweroff code for all AT91 SoCs but the RM9200,
and the ram controller driver is not doing much at the time, except for grabing
the RAM clock in order to leave it always enabled."
Conflicts:
arch/arm/mach-at91/Kconfig
Remove all the material related to AIC5 support: this interrupt controller
driver is now implemented in drivers/irqchip/atmel-aic.c.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Remove selection of OLD_IRQ_AT91 when selecting dt boards.
Select ATMEL_AIC_IRQ for sama5 SoCs (a kernel compiled for this SoC will
always use ATMEL_AIC_IRQ driver).
Select ATMEL_AIC_IRQ for at91rm9200 and at91sam9 SoCs only if OLD_IRQ_AT91
is not selected (which means we are compiling a pure DT kernel, without
any legacy board support).
Remove specific irq init code in all dt board files: this init procedure
is automatically handled in of_irq_init which is called by the arm irq core
code and is in charge of calling the appropriate aic init functions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enclose at91_aic_xx calls in IS_ENABLED(CONFIG_OLD_IRQ_AT91) blocks in
order to prepare migration to the new AIC driver.
In the new AIC driver the suspend/resume functions are called by the
generic irq framework and are no longer needed in the PM specific code.
Moreover, the new AIC driver no longer exposes the at91_aic_base variable
which is used by the at91_aic_read functions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Introduce the OLD_IRQ_AT91 Kconfig option to prepare migration to the
new AIC driver.
Select this option for all at91 SoCs and all available boards so that we
can later move DT enabled boards to the new irq driver and keep the old
implementation when legacy boards are selected.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
cycle, and this time we got a lot of action going on and
it will continue:
- The core GPIO library implementation has been split up in
three different files:
- gpiolib.c for the latest and greatest and shiny GPIO
library code using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API
that we are phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are
not entirely happy with, but has to live on for
ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We
should have had the flags there from the beginning it
seems, now we need to clean up the mess. There is a plan
on how to move forward here devised by Alexandre Courbot
and Mark Brown.
- Split off a special <linux/gpio/machine.h> header for the
board gpio table registration, as per example from the
regulator subsystem.
- Start to kill off the return value from gpiochip_remove()
by removing the __must_check attribute and removing all
checks inside the drivers/gpio directory. The rationale
is: well what were we supposed to do if there is an error
code? Not much: print an error message. And gpiolib already
does that. So make this function return void eventually.
- Some cleanups of hairy gpiolib code, make some functions
not to be used outside the library private and make sure
they are not exported, remove gpiod_lock/unlock_as_irq()
as the existing function is for driver-internal use and
fine as it is, delete gpio_ensure_requested() as it is
not meaningful anymore.
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one()
function calls, which is logical since this is already
supported when referencing GPIOs from e.g. device trees.
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use
the gpiolib irqchip helpers cutting down on GPIO irqchip
boilerplate a bit more.
- New driver for the Zynq GPIO block.
- The usual incremental improvements around a bunch of
drivers.
- Janitorial syntactic and semantic cleanups by Jingoo Han,
and Rickard Strandqvist especially.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e+d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO update from Linus Walleij:
"This is the bulk of GPIO changes for the v3.17 development cycle, and
this time we got a lot of action going on and it will continue:
- The core GPIO library implementation has been split up in three
different files:
- gpiolib.c for the latest and greatest and shiny GPIO library code
using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API that we are
phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are not entirely
happy with, but has to live on for ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We should have
had the flags there from the beginning it seems, now we need to
clean up the mess. There is a plan on how to move forward here
devised by Alexandre Courbot and Mark Brown
- Split off a special <linux/gpio/machine.h> header for the board
gpio table registration, as per example from the regulator
subsystem
- Start to kill off the return value from gpiochip_remove() by
removing the __must_check attribute and removing all checks inside
the drivers/gpio directory. The rationale is: well what were we
supposed to do if there is an error code? Not much: print an error
message. And gpiolib already does that. So make this function
return void eventually
- Some cleanups of hairy gpiolib code, make some functions not to be
used outside the library private and make sure they are not
exported, remove gpiod_lock/unlock_as_irq() as the existing
function is for driver-internal use and fine as it is, delete
gpio_ensure_requested() as it is not meaningful anymore
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one() function
calls, which is logical since this is already supported when
referencing GPIOs from e.g. device trees
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use the gpiolib
irqchip helpers cutting down on GPIO irqchip boilerplate a bit more
- New driver for the Zynq GPIO block
- The usual incremental improvements around a bunch of drivers
- Janitorial syntactic and semantic cleanups by Jingoo Han, and
Rickard Strandqvist especially"
* tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (37 commits)
MAINTAINERS: update GPIO include files
gpio: add missing includes in machine.h
gpio: add flags argument to gpiod_get*() functions
MAINTAINERS: Update Samsung pin control entry
gpio / ACPI: Move event handling registration to gpiolib irqchip helpers
gpio: lynxpoint: Convert to use gpiolib irqchip
gpio: split gpiod board registration into machine header
gpio: remove gpio_ensure_requested()
gpio: remove useless check in gpiolib_sysfs_init()
gpiolib: Export gpiochip_request_own_desc and gpiochip_free_own_desc
gpio: move gpio_ensure_requested() into legacy C file
gpio: remove gpiod_lock/unlock_as_irq()
gpio: make gpiochip_get_desc() gpiolib-private
gpio: simplify gpiochip_export()
gpio: remove export of private of_get_named_gpio_flags()
gpio: Add support for GPIOF_ACTIVE_LOW to gpio_request_one functions
gpio: zynq: Clear pending interrupt when enabling a IRQ
gpio: drop retval check enforcing from gpiochip_remove()
gpio: remove all usage of gpio_remove retval in driver/gpio
devicetree: Add Zynq GPIO devicetree bindings documentation
...
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
As per example from the regulator subsystem: put all defines and
functions related to registering board info for GPIO descriptors
into a separate <linux/gpio/machine.h> header.
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When using device tree, select the Atmel RAM controller driver to handle its
clocks.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The IP for the SDRAM controller found on sama5d3 SoCs is different from the g45
one. Introduce a new compatible string to reflect that.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch removes the selection of AT91_USE_OLD_CLK when selecting
at91sam9263 SoC support. This will automatically enable COMMON_CLK_AT91
option and add support for at91 common clock implementation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enclose the sam9263 old clk registration in "#if defined(CONFIG_OLD_CLK_AT91)
#endif"
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch removes the selection of AT91_USE_OLD_CLK when selecting at91sam9g45
SoC support. This will automatically enable COMMON_CLK_AT91 option and add
support for at91 common clock implementation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enclose the sam9g45 old clk registration in "#if defined(CONFIG_OLD_CLK_AT91)
#endif"
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch removes the selection of AT91_USE_OLD_CLK when selecting at91sam9260
SoCs support. This will automatically enable COMMON_CLK_AT91 option and add
support for at91 common clk implementation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enclose the sam9260 old clk registration in "#if defined(CONFIG_OLD_CLK_AT91)
#endif"
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch removes the selection of AT91_USE_OLD_CLK when selecting at91rm9200
SoC support. This will automatically enable COMMON_CLK_AT91 option and add
support for at91 common clk implementation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enclose the rm9200 old clk registration in "#if defined(CONFIG_OLD_CLK_AT91)
#endif"
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Now that all at91 boards using leds-atmel-pwm switched to leds-pwm, the
at91_pwm_leds() function is not used anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Switch to the pwm/pwm-atmel driver instead of misc/atmel_pwm
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Switch to the generic leds_pwm driver instead of leds-atmel-pwm.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Switch to the pwm/pwm-atmel driver instead of misc/atmel_pwm
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Switch to the generic leds_pwm driver instead of leds-atmel-pwm.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Switch to the pwm/pwm-atmel driver instead of misc/atmel_pwm
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
sam9x5 SoCs have the following errata:
"RTC: Interrupt Mask Register cannot be used
Interrupt Mask Register read always returns 0."
Hence we should not rely on what IMR claims about already masked IRQs
and just disable all IRQs.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Bryan Evenson <bevenson@melinkcorp.com>
Reviewed-by: Johan Hovold <johan@hovold.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Bryan Evenson <bevenson@melinkcorp.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mark Roszko <mark.roszko@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big tty / serial driver pull request for 3.16-rc1.
A variety of different serial driver fixes and updates and additions,
nothing huge, and no real major core tty changes at all.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONXgoACgkQMUfUDdst+ymdSwCgwL0xmWjFYr/UbJ4LslOZ29Q4
BFQAoKyYe9LsfEyodBPabxJjKUtj1htz
=ZGSN
-----END PGP SIGNATURE-----
Merge tag 'tty-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty into next
Pull tty/serial driver updates from Greg KH:
"Here is the big tty / serial driver pull request for 3.16-rc1.
A variety of different serial driver fixes and updates and additions,
nothing huge, and no real major core tty changes at all.
All have been in linux-next for a while"
* tag 'tty-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (84 commits)
Revert "serial: imx: remove the DMA wait queue"
serial: kgdb_nmi: Improve console integration with KDB I/O
serial: kgdb_nmi: Switch from tasklets to real timers
serial: kgdb_nmi: Use container_of() to locate private data
serial: cpm_uart: No LF conversion in put_poll_char()
serial: sirf: Fix compilation failure
console: Remove superfluous readonly check
console: Use explicit pointer type for vc_uni_pagedir* fields
vgacon: Fix & cleanup refcounting
ARM: tty: Move HVC DCC assembly to arch/arm
tty/hvc/hvc_console: Fix wakeup of HVC thread on hvc_kick()
drivers/tty/n_hdlc.c: replace kmalloc/memset by kzalloc
vt: emulate 8- and 24-bit colour codes.
printk/of_serial: fix serial console cessation part way through boot.
serial: 8250_dma: check the result of TX buffer mapping
serial: uart: add hw flow control support configuration
tty/serial: at91: add interrupts for modem control lines
tty/serial: at91: use mctrl_gpio helpers
tty/serial: Add GPIOLIB helpers for controlling modem lines
ARM: at91: gpio: implement get_direction
...
As with previous release, this continues to be among the largest branches
we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=OvOG
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC devicetree updates from Olof Johansson:
"As with previous release, this continues to be among the largest
branches we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q"
* tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (500 commits)
ARM: dts: add secure firmware support for exynos5420-arndale-octa
ARM: dts: add pmu sysreg node to exynos3250
ARM: dts: correct the usb phy node in exynos5800-peach-pi
ARM: dts: correct the usb phy node in exynos5420-peach-pit
ARM: dts: add dts files for exynos5410 and exynos5410-smdk5410
ARM: dts: add dts files for exynos3250 SoC
ARM: dts: add mfc node for exynos5800
ARM: dts: add Vbus regulator for USB 3.0 on exynos5800-peach-pi
ARM: dts: enable fimd for exynos5800-peach-pi
ARM: dts: enable display controller for exynos5800-peach-pi
ARM: dts: enable hdmi for exynos5800-peach-pi
ARM: dts: add dts file for exynos5800-peach-pi board
ARM: dts: add dts file for exynos5800 SoC
ARM: dts: add dts file for exynos5260-xyref5260 board
ARM: dts: add dts files for exynos5260 SoC
ARM: dts: update watchdog node name in exynos5440
ARM: dts: use key code macros on Origen and Arndale boards
ARM: dts: enable RTC and WDT nodes on Origen boards
ARM: dts: qcom: Add APQ8084-MTP board support
ARM: dts: qcom: Add APQ8084 SoC support
...
A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support for
big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation and
moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as most
of the other v7 platforms in the tree. \o/ The work isn't quite complete,
there's some driver fixes still needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
Plus a large set of various smaller updates for different platforms. I'm
probably missing some important one here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6LYI
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
On sam9x5, dedicated CTS (and RTS) pins are unusable together with the
LCDC, the EMAC, or the MMC because they share the same line.
Moreover, the USART controller doesn't handle DTR/DSR/DCD/RI signals,
so we have to control them via GPIO.
This patch permits to use GPIOs to control the CTS/RTS/DTR/DSR/DCD/RI
signals.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed for gpiod_get_direction().
Otherwise, it returns -EINVAL.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- two fixes concerning iio ADC triggers for at91sam9260 and at91sam9g20
one for the "device" file, the other for the DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJTfjD/AAoJEAf03oE53VmQ1p0IAJL/FmsbXfHLLu8KvQEXMW8W
Y3c22v2mHSHpEFjqjFg+LbOkRbFaPTlszSXuKyw7HJPiOygUk/C1i2MUW4WLNlyY
fqu+tiAOrcfJ8rapM5ndFdeMZrkyRQIInFEPzOttQJSN4Aczpc6irfMqOOqw0y/s
Sf88MiK2YgeXnt5dH6mDYhy29glvspek3w1FmDN3DjmiAdxAUV8bSpOmw2FsFAX7
QJOwkevln+3Ddxnq+NsG/6KxdAl0fj+G3shl4GwALr+hizKypzsFsSGDuyKuAL2o
A7e+OFoUWN8eCTJBdP9YA/lVyl83uFMM3tBcHr4Oq8dJk6sQ0GNQcdJuCUBGTBw=
=ehhW
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes2' of git://github.com/at91linux/linux-at91 into fixes
Second 3.15 fixes for AT91
- two fixes concerning iio ADC triggers for at91sam9260 and at91sam9g20
one for the "device" file, the other for the DT.
* tag 'at91-fixes2' of git://github.com/at91linux/linux-at91:
ARM: at91: sam9260: fix compilation issues
ARM: at91/dt: sam9260: correct external trigger value
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use the hexadecimal values for the triggers to match what is done for the device
tree. This also fixes compilation issues as the defines have been moved
elsewhere.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch removes the selection of AT91_USE_OLD_CLK when selecting
sam9n12 SoC support. This will automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch encloses sam9n12 old clk registration in
"#if defined(CONFIG_OLD_CLK_AT91) #endif" sections.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch removes the selection of AT91_USE_OLD_CLK when selecting
sam9x5 SoCs support. This will automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch encloses sam9x5 old clk registration in
"#if defined(CONFIG_OLD_CLK_AT91) #endif" sections.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
atmel_tsadcc is not allowing to use the remaining ADC channels while at91_adc
does. Completely switch to at91_adc and remove the tsadcc platform_data for
at91sam9rl and at91sam9rl based boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
atmel_tsadcc is not allowing to use the remaining ADC channels while at91_adc
does. Completely switch to at91_adc and remove the tsadcc platform_data for
at91sam9g45 and at91sam9g45 based boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
at91_adc now supports reading a touchscreen for ADCs without a TSMR register.
Enable touchscreen support through at91_adc. This allows to use both a
touchscreen and the remaining ADC channel at the same time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The ADC clock needs to be defined to enable the at91_adc driver. It is defined
to the same speed that is used for atmel_tsadcc.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
That include file is now only used by the at91_adc driver, remove it from
include/mach for better driver separation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
at91_adc now supports reading a touchscreen for ADCs without a TSMR register.
Enable touchscreen support through at91_adc. This allows to use both a
touchscreen and the remaining ADC channel at the same time.
Also, lower the clock for the ADC as it allows to have more stable reads and
this is the speed used by atmel_tsadcc.
It lowers the maximum throughput rate from 440000 samples per second to 12958
samples per second. It shouldn't be an issue as the CPU is not able to keep up
reading samples at that frequency.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Old ADCs, as present on the sam9rl and the sam9g45 don't have a TSMR register
and the touchscreen support should be handled differently.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
num_channels and registers are not used anymore since they are defined inside
the at91_adc driver and assigned by matching the id_table.
Also, remove the mach/at91_adc.h include that is not necessary anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
num_channels and registers are not used anymore since they are defined inside
the at91_adc driver and assigned by matching the id_table.
Also, remove the mach/at91_adc.h include that is not necessary anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This moves the <mach/gpio.h> header in the AT91 platform down
into the machine directory and removes the reliance on
MACH_NEED_GPIO_H from the AT91.
This does not move the platform to GENERIC_GPIO but localize
the remaining work to be done for this to the mach-at91
folder.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[nicolas.ferre@atmel.com: adapt to newer kernel, add rsi-ews board]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* Fix the platform data support for the at91 adc driver.
* A couple of related follow up patches get the support working again
for at91sam9260 and at91sam9g45 as the earlier patch results in a device
name change.
* A default timer value in the at91 adc driver was bonkers. Make it sane.
* Fix incorrect reporting of the integration time for the cm32181 light sensor
* Fix a missing break in the ad2s1200 driver which would have give a false
error return.
* Make sure buffer scan mask queries from userspace return 0/1 rather than
a fairly random value depending on their implementation of test_bit
* Fix leak of the i2c client and a null pointer dereference in the cm36651
driver.
* Fix a build warning on avr32 for the mxs-lradc (not exactly a critical
combination - but the issue was real).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=HMr3
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First found of IIO fixes for the 3.15 cycle.
* Fix the platform data support for the at91 adc driver.
* A couple of related follow up patches get the support working again
for at91sam9260 and at91sam9g45 as the earlier patch results in a device
name change.
* A default timer value in the at91 adc driver was bonkers. Make it sane.
* Fix incorrect reporting of the integration time for the cm32181 light sensor
* Fix a missing break in the ad2s1200 driver which would have give a false
error return.
* Make sure buffer scan mask queries from userspace return 0/1 rather than
a fairly random value depending on their implementation of test_bit
* Fix leak of the i2c client and a null pointer dereference in the cm36651
driver.
* Fix a build warning on avr32 for the mxs-lradc (not exactly a critical
combination - but the issue was real).
These cleanup patches are mainly move stuff around and should all
be harmless. They are mainly split out so that other branches can
be based on top to avoid conflicts.
Notable changes are:
* We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used. (Uwe Kleine-König)
* The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions. (Kumar Gala)
* A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
* Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
* mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
* at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GcBb
-----END PGP SIGNATURE-----
Merge tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These cleanup patches are mainly move stuff around and should all be
harmless. They are mainly split out so that other branches can be
based on top to avoid conflicts.
Notable changes are:
- We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used (Uwe Kleine-König)
- The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions (Kumar Gala)
- A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
- Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
- mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
- at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people)"
* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
ARM: hisi: select HAVE_ARM_SCU only for SMP
ARM: efm32: allow uncompress debug output
ARM: prima2: build reset code standalone
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
...
My recent commit 871336a937 "ARM: at91: fix broken "if () else" statement"
introduced a typo because of a last-minute fixup. This adds the missing
closing parenthesis.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It makes no sense for sama5 support to be enabled if we don't
also enable USE_OF. Making this automatic in Kconfig avoids
a possible randconfig conflict between the old and new clock
support code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
If CONFIG_PATA_AT91 is disabled, the code in at91_add_device_cf
is turned into invalid C statements due to the lack of an
expression before the 'else' clause.
This moves the first half of the condition inside of the #ifdef,
which seems to be what the author intended.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
The pata_at91 driver uses interfaces defined in the sam9_smc
platform code. Since the pata driver can be a loadable module,
we have to export those symbols in order to link cleanly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
at91x40 has no support for device tree, but Kconfig allows
us to enable CONFIG_OF anyway, causing a link error in the
at91 reset controller initialization.
The easiest fix is to adapt the existing #ifdef to omit
the broken code on at91x40 where it is never called anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
at91x40 is different from all the other at91 machines, and it is
impossible to build a kernel that works on both this SoC and
any of the others, even though it is possible to build a noMMU
kernel for any at91 machine.
By turning at91x40 into a separate top-level option, we explicitly
forbid enabling invalid configurations that include mutually exclusive
machines.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
- some updates on the defconfig front
- two SoCs converted to Device Tree: sam9261 and sam9rl
(with use of CCF!)
- a little PWM clock update that goes on top of this
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJTIJ7GAAoJEAf03oE53VmQ3xgIAMtWSo91ENlnr38ZtEN+J71j
lrUdI/0sfv4pY2Dw0VbrnFS4hNmvM25C4dIR7SxU3iOnIC0vzzkPqs2hdRHwUY6y
pw9NsnF3kW950vf/M6nDmHxQpwKZOCpABs5EDjO6S4Ky6sze4IPog+vb5Y7ovGCl
LSqL9col3RCHIGyBWq77T3/NbWKOrz67Fy3eqJRyio7H8zYaEGnIrm2jPXYwtToT
/FB9sZUunjYwdTRdGNhRiTHWktwlr4i4f8woHTZg85MGKY6DOsZgxzUvCXdGBeJx
XaQ70hE8BF78Lglx8WUBgxowxJ1FvehxxcfzoYAVafwMlik+tSd3l0Zq3Sf6xD8=
=Q3FC
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
Merge "First batch of AT91 cleanup for 3.15" from Nicolas Ferre:
- some updates on the defconfig front
- two SoCs converted to Device Tree: sam9261 and sam9rl
(with use of CCF!)
- a little PWM clock update that goes on top of this
* tag 'at91-cleanup' of git://github.com/at91linux/linux-at91:
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
ARM: at91/defconfig: remove useless configuration in at91sam9260_9g20_defconfig
ARM: at91/defconfig: refresh at91sam9rl_defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We can't use "at91_adc" to refer to the at91_adc driver anymore as
the name is used to match an id_table.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We can't use "at91_adc" to refer to the at91_adc driver anymore as the name is
used to match an id_table.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add PWM clock for AT91 series SoC which include PWM controller.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch removes the selection of AT91_USE_OLD_CLK when selecting
sam9261 SoCs support. This will automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds support for the Device Tree on a sam9261-based platform
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch encloses sam9rl old clk registration in
#if defined(CONFIG_OLD_CLK_AT91)/#endif sections.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch prepare the transition to common clk for sam9 dt boards by
replacing the timer init callback.
Clocks registration cannot be done in early init callback (as formerly done
by the old clk implementation) because it requires dynamic allocation
which is not ready yet during early init.
In the other hand, at91 clocks must be registered before
at91sam926x_pit_init is called because PIT (Periodic Interval Timer) driver
request the master clk (mck).
A new function (at91sam9_dt_timer_init) is created to fullfil these needs.
This function registers all at91 clks using the dt definition before
calling the PIT init function.
The device tree clock registration is enabled only if common clk is
selected. Else the old clk registration is been done during
at91_dt_initialize call.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the new names, coming from DT, for the clock lookups.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
