WARNING: vmlinux.o(.text+0x4f568): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.setup_hvlpevent_queue' and '.process_hvlpevents')
setup_hvlpevent_queue is only called from __init code so make it __init
as well.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
spufs.h now has two enums for the sched_flags leading to identical
values for SPU_SCHED_WAS_ACTIVE and SPU_SCHED_NOTIFY_ACTIVE. Merge
them into a single enum as they were in the IBM development tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting the host bridge @8000 as primary. Also fixing a bug in
setting the USB interrupt numbers.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The interrupts of an E100 card inserted in PCI slot 4 may be on at bootup.
The resulting interrupt flood interacts with the 8259 cascade handler and
prevents proper boot up. There is a quirk for the E100 that will disable
the E100's interrupts but to use it, the 8259 cascade hookup must be
delayed until after the quirk has run. This patch delays the 8259 cascade
hookup by registering a device_initcall() which runs after the PCI quirk
for the E100.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current 85xxCDS restart code fails to reset the PCI bus which can
lead to odd behavior after the restart. This patch uses the VIA Super
Southbridge to perform a PCI reset which will reset the entire system.
NOTE: Since the VIA chip is behind a PCI-to-PCI bridge which can be
disabled with a switch setting, it may not be possible to perform the
PCI bus reset. In this case, the code defaults to the previous restart
mechanism.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale MPC8555CDS and MPC8548CDS reference hardware has a legacy
8259 interrupt controller pair contained within a VIA VT82C686B Southbridge
on the main carrier board. The processor complex plugs into the carrier
card using a PCI slot which limits the available interrupts to the
INTA-INTD PCI interrupts. The output of the 8259 cascade pair is routed
through a gate array and connected to the PCI INTA interrupt line.
The normal interrupt chaining hook (set_irq_chained_handler) does
not allow sharing of the chained interrupt which prevents the
use of PCI INTA by PCI devices. This patch allows the 8259 cascade
pair to share their interrupt line with PCI devices.
NOTE: The addition of the .end routine for the MPIC is not strictly
necessary for this patch. It's there so this code will run from within
the threaded interrupt context used by the Real Time patch.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic support for the PCIe PHB and enable the ULI bridge.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make it so we do a runtime check to know if we need to write cfg_addr
as big or little endian. This is needed if we want to allow 86xx support
to co-exist in the same kernel as other 6xx PPCs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The newer Arcadia boards for CDS have an FPGA that shows up on PCI
however isn't a real PCI device. Add a quirk to just ignore the
FPGA.
This is based on the following patch from Andy & York:
http://ozlabs.org/pipermail/linuxppc-dev/2007-February/032042.html
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the 85xx/86xx PCIe controllers if there is no device connected to the
PHB we will still allocate a pci_bus for downstream bus of the virtual
P2P bridge. However the resources allocated to the downstream bus are not
correct and so we just mimic the resources from the upstream pci_bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Switch the 85xx platform over to using the FSL generic PCI code. This
gets ups PCIe support in addition to base PCI support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rewrite the Freescale PCI code to support PCI on 83xx/85xx/86xx and
PCIe on 85xx/86xx.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move
arch/powerpc/platforms/86xx/pci.c -> arch/powerpc/sysdev/fsl_pci.c
arch/powerpc/sysdev/fsl_pcie.h -> arch/powerpc/sysdev/fsl_pci.h
as the base to unify 83xx/85xx/86xx pci and pcie.
Add CONFIG_FSL_PCI to build fsl_pci.c for Freescale pci and pcie option.
The code still works for 86xx platforms.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Clean up duplicate includes in drivers/macintosh/
[POWERPC] Quiet section mismatch warning on pcibios_setup
[POWERPC] init and exit markings for hvc_iseries
[POWERPC] Quiet section mismatch in hvc_rtas.c
[POWERPC] Constify of_platform_driver match_table
[POWERPC] hvcs: Make some things static and const
[POWERPC] Constify of_platform_driver name
[POWERPC] MPIC protected sources
[POWERPC] of_detach_node()'s device node argument cannot be const
[POWERPC] Fix ARCH=ppc builds
[POWERPC] mv64x60: Use mutex instead of semaphore
[POWERPC] Allow smp_call_function_single() to current cpu
[POWERPC] Allow exec faults on readable areas on classic 32-bit PowerPC
[POWERPC] Fix future firmware feature fixups function failure
[POWERPC] fix showing xmon help
[POWERPC] Make xmon_write accept a const buffer
[POWERPC] Fix misspelled "CONFIG_CHECK_CACHE_COHERENCY" Kconfig option.
[POWERPC] cell: CONFIG_SPE_BASE is a typo
Fix a mismerge in commit 8b6f50ef1d:
"spufs: make signal-notification files readonly for NOSCHED contexts",
where structs got duplicated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move firmware feature initialisation from pSeries_init_early to the
earlier pSeries_probe_hypertas so they are initialised before firmware
feature fixups are applied.
Currently firmware feature sections are only used for iSeries which
initialises the these features much earlier. This is a bug in waiting
on pSeries.
Also adds some whitespace fixups.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reading from the signal{1,2} files requires a spu_acquire_saved, so make these
files write-only for contexts created with SPU_CREATE_NOSCHED.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a FLASH ROM Storage Driver for the PS3:
- Implemented as a misc character device driver
- Uses a fixed 256 KiB buffer allocated from boot memory as the hypervisor
requires the writing of aligned 256 KiB blocks
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a BD/DVD/CD-ROM Storage Driver for the PS3:
- Implemented as a SCSI device driver
- Uses software scatter-gather with a 64 KiB bounce buffer as the hypervisor
doesn't support scatter-gather
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a Disk Storage Driver for the PS3:
- Implemented as a block device driver with a dynamic major
- Disk names (and partitions) are of the format ps3d%c(%u)
- Uses software scatter-gather with a 64 KiB bounce buffer as the hypervisor
doesn't support scatter-gather
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This sorts out the various lists and related locks in the spu code.
In detail:
- the per-node free_spus and active_list are gone. Instead struct spu
gained an alloc_state member telling whether the spu is free or not
- the per-node spus array is now locked by a per-node mutex, which
takes over from the global spu_lock and the per-node active_mutex
- the spu_alloc* and spu_free function are gone as the state change is
now done inline in the spufs code. This allows some more sharing of
code for the affinity vs normal case and more efficient locking
- some little refactoring in the affinity code for this locking scheme
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
From: Maynard Johnson <mpjohn@us.ibm.com>
This patch updates the existing arch/powerpc/oprofile/op_model_cell.c
to add in the SPU profiling capabilities. In addition, a 'cell' subdirectory
was added to arch/powerpc/oprofile to hold Cell-specific SPU profiling code.
Exports spu_set_profile_private_kref and spu_get_profile_private_kref which
are used by OProfile to store private profile information in spufs data
structures.
Also incorporated several fixes from other patches (rrn). Check pointer
returned from kzalloc. Eliminated unnecessary cast. Better error
handling and cleanup in the related area. 64-bit unsigned long parameter
was being demoted to 32-bit unsigned int and eventually promoted back to
unsigned long.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
From: Maynard Johnson <mpjohn@us.ibm.com>
This patch adds to the capability of spu_switch_event_register so that
the caller is also notified of currently active SPU tasks.
Exports spu_switch_event_register and spu_switch_event_unregister so
that OProfile can get access to the notifications provided.
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Sort out the locking mess in spu_base and document the current rules.
As an added benefit spu_alloc* and spu_free don't block anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch links spus according to their physical position using
information provided by the firmware through a special vicinity
device-tree property. This property is present in current version
of Malta firmware.
Example of vicinity properties for a node in Malta:
Node: Vicinity property contains phandles of:
spe@0 [ spe@100000 , mic-tm@50a000 ]
spe@100000 [ spe@0 , spe@200000 ]
spe@200000 [ spe@100000 , spe@300000 ]
spe@300000 [ spe@200000 , bif0@512000 ]
spe@80000 [ spe@180000 , mic-tm@50a000 ]
spe@180000 [ spe@80000 , spe@280000 ]
spe@280000 [ spe@180000 , spe@380000 ]
spe@380000 [ spe@280000 , bif0@512000 ]
Only spe@* have a vicinity property (e.g., bif0@512000 and
mic-tm@50a000 do not have it).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch makes the scheduller honor affinity information for each
context being scheduled. If the context has no affinity information,
behaviour is unchanged. If there are affinity information, context is
schedulled to be run on the exact spu recommended by the affinity
placement algorithm.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch provides the spu affinity placement logic for the spufs scheduler.
Each time a gang is going to be scheduled, the placement of a reference
context is defined. The placement of all other contexts with affinity from
the gang is defined based on this reference context location and on a
precomputed displacement offset.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds support for additional flags at spu_create, which relate
to the establishment of affinity between contexts and contexts to memory.
A fourth, optional, parameter is supported. This parameter represent
a affinity neighbor of the context being created, and is used when defining
SPU-SPU affinity.
Affinity is represented as a doubly linked list of spu_contexts.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch allows the use of spu affinity on QS20, whose
original FW does not provide affinity information.
This is done through two hardcoded arrays, and by reading the reg
property from each spu.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds affinity data to each spu instance.
A doubly linked list is created, meant to connect the spus
in the physical order they are placed in the BE. SPUs
near to memory should be marked as having memory affinity.
Adjustments of the fields acording to FW properties is done
in separate patches, one for CPBW, one for Malta (patch for
Malta under testing).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Addition of a spufs-global "cbe_info" array. Each entry contains information
about one Cell/B.E. node, namelly:
* list of spus (both free and busy spus are in this list);
* list of free spus (replacing the static spu_list from spu_base.c)
* number of spus;
* number of reserved (non scheduleable) spus.
SPE affinity implementation actually requires only access to one spu per
BE node (since it implements its own pointer to walk through the other spus
of the ring) and the number of scheduleable spus (n_spus - non_sched_spus)
However having this more general structure can be useful for other
functionalities, concentrating per-cbe statistics / data.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
spu_sched->bitmap has MAX_PRIO(=140) width in bits.However, since
ff80a77f20, sched_find_first_bit()
only supports 100-bit bitmaps.
Thus, spu_sched->bitmap should be treated by generic find_first_bit().
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
From: Sebastian Siewior <cbe-oss-dev@ml.breakpoint.cc>
The 'file' argument is unused in spufs_run_spu(). This change removes
it.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The SPU decrementer should be restored after the LSCSA DMA has
completed.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
No need to halt the SPE decrementer at context restore step 47, it will
be done in step 7.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
At save step 8, the mfc control register in the CSA should be written
_only_ with Sc and Sm bits (at least MFC_CNTL[Dh] should be set to 0)
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The decr_status in the LSCSA is valid only in the sequence of context
restore. Thus, it's nonsense to read and/or write it through spufs.
This patch changes decr_status node to access MFC_CNTL[Ds] in the CSA.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The decr_status in the LSCSA is confusedly used as two meanings:
* SPU decrementer was running
* SPU decrementer was wrapped as a result of adjust
and the code to set decr_status is missing.
This patch fixes these problems by using the decr_status argument as a
set of flags. This requires a rebuild of the shipped spu_restore code.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The following steps are not needed in the SPE context save/restore
paths:
Save Step 12: save_mfc_decr()
save suspend_time to CSA (It will be done by step 14)
save ch 7 (decrementer value will be saved in LSCSA by spe-side step 10)
Restore Step 59: restore_ch_part1()
restore ch 1 (it will be done by spe-side step 15)
This change removes the unnecessary steps.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Based on a fix from Masato Noguchi <Masato.Noguchi@jp.sony.com>.
Remove the (incorrect) array size declarations in the spufs channel
arrays, and use ARRAY_SIZE rather than hardcoded values.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Currently a process is removed from the physical spu when spu_acquire_saved
is saved but never put back. This patch adds a new spu_release_saved
that is to be paired with spu_acquire_saved and put the process back if
it has been in RUNNABLE state before.
Niether Jeremy not be are entirely happy about this exact patch because
it adds another spu_activate call outside of the owner thread, but I
feel this is the best short-term fix we can come up with.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch exports per-context statistics in spufs as long as spu
statistics in sysfs.
It was formed by merging:
"spufs: add spu stats in sysfs" From: Christoph Hellwig
"spufs: add stat file to spufs" From: Christoph Hellwig
"spufs: fix libassist accounting" From: Jeremy Kerr
"spusched: fix spu utilization statistics" From: Luke Browning
And some adjustments by myself, after suggestions on cbe-oss-dev.
Having separate patches was making the review process harder
than it should, as we end up integrating spus and ctx statistics
accounting much more than it was on the first implementation.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
In 6cbf93960e64f313f6e247cbca7afaa50e3ee2c we added a WARN_ON for
calling spu_deactivate on contexts created with the SPU_CREATE_NOSCHED
flag. However, all NOSCHED contexts will need to be deactivated when
the context is destroyed, so this gives a spurious warning when any
NOSCHED context is closed.
This change removes the WARN_ON.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Reading from the signal{1,2} files requires a spu_acquire_saved, so
make these files write-only for contexts created with
SPU_CREATE_NOSCHED.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The current SPU context saving procedure in SPUFS unexpectedly
restarts MFC when halting decrementer, because MFC_CNTL[Dh] is set
without MFC_CNTL[Sm]. This bug causes, for example, saving broken DMA
queues. Here is a patch to fix the problem.
Signed-off-by: Kazunori Asayama <asayama@sm.sony.co.jp>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
WARNING: arch/powerpc/platforms/cell/spufs/spufs.o(.init.text+0x158): Section
mismatch: reference to .exit.text:.spu_sched_exit (between '.init_module' and
'.spu_sched_init')
was introduced by c99c1994a2
This patch removes the warning.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds support for the setup and decoding of MSIs
on Axon-based Cell systems, using the MSIC mechanism.
This involves setting up an area of BE memory which the Axon
then uses as a FIFO for MSI messages. When one or more MSIs
are decoded by the MSIC we receive an interrupt on the MPIC,
and the MSI messages are written into the FIFO. At the moment
we use a 64KB FIFO, one per MSIC/BE.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds support for investigating spus information after a
kernel crash event, through kdump vmcore file.
Implementation is based on xmon code, but the new functionality was
kept independent from xmon.
Signed-off-by: Lucio Jose Herculano Correia <luciojhc@br.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The Axon bridge chip used on new Cell/B.E. based blade servers
comes with a DDR2 memory controller that can be used to
attach cheap memory modules, as opposed to the high-speed
XDR memory that is used by the CPU itself.
Since the memory controller does not participate in the
cache coherency protocol, we can not use the memory direcly
for Linux applications, but by providing a block device
it can be used for swap space, temporary file storage and
through the use of the direct_access block device operation
for mapping into user addresses, when it is mounted with
an appropriate file system.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The platforms missing the "cpus" property in the "be" node are mono-Cell
platforms such as CAB or Getaway.
Therefore it is possible to assume that if there is no "cpus" properties
under the "be" node then we can safely return the "device node" without
more checking. This is a bit hacky but ... it allows it to work on
these platforms.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Acked-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Previous patch changed based on Christian Krafft's comment.
On some legacy SLOF tree the generic code is unable to ioremap some Cell BE
registers. Therefore the "generic" functions are returning a NULL pointer,
triggering a crash on such platforms.
Let's handle this more gracefully.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Acked-by: Christian Kraff <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Previous patch changed based on Christian Krafft's comment.
On some legacy SLOF tree the generic code is unable to ioremap some Cell BE
registers. Therefore the "generic" functions are returning a NULL pointer,
triggering a crash on such platforms.
Let's handle this more gracefully.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Acked-by: Christian Kraff <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch reorganizes the code of the driver into three files.
Two cbe_cpufreq_pmi.c and cbe_cpufreq_pervasive.c care about hardware.
cbe_cpufreq.c contains the logic.
There is no changed behaviour, except that the PMI related function
is now located in a seperate module cbe_cpufreq_pmi. This module
will be required by cbe_cpufreq, if CONFIG_CBE_CPUFREQ_PMI has been set.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Minor issues have been fixed:
* added a missing call to of_node_put()
* signedness of a function parameter
* added some line breaks
* changed global pmi_frequency_limit to a
per node pmi_slow_mode_limit array
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch fixes the initialization of the cbe_cpufreq driver.
The code that initializes the PMI related functions was called per cpu:
* registering cpufreq notifier block
* registering a pmi handler
This ends in a bug that the notifier block gets called in an endless loop.
The initialization code is being put to the
module init code path by this patch. This way it only gets called once.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch fixes the debug code that calculates the transition time when
changing the slow modes on a Cell BE cpu.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The pmi driver got simplified by removing support for multiple devices.
As there is no more than one pmi device per maschine, there is no need to
specify the device for listening and sending messages.
This way the caller (cbe_cpufreq) doesn't need to scan the device tree.
When registering the handler on a board without a pmi
interface, pmi.c will just return -ENODEV.
The patch that fixed the breakage of cell_defconfig has been
broken out of the earlier version of this patch. So this is
the version that applies cleanly on top of it.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
83c54070ee broke spufs by incorrectly
updating the code, this patch gets it to compile again.
It's probably still broken due to the scheduler changes, but this
at least makes sure cell kernels can still be built.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch completes Linus's wish that the fault return codes be made into
bit flags, which I agree makes everything nicer. This requires requires
all handle_mm_fault callers to be modified (possibly the modifications
should go further and do things like fault accounting in handle_mm_fault --
however that would be for another patch).
[akpm@linux-foundation.org: fix alpha build]
[akpm@linux-foundation.org: fix s390 build]
[akpm@linux-foundation.org: fix sparc build]
[akpm@linux-foundation.org: fix sparc64 build]
[akpm@linux-foundation.org: fix ia64 build]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Still apparently needs some ARM and PPC loving - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let spu_management_ops.enumerate_spus() return the number of found SPEs
and use that information to draw some little helper penguin logos.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-By: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rolling forward PCMCIA driver, it was discovered that the indentation in
existing one, as well as in BSP side are very odd. This patch is just result
of Lindent run ontop of culprit files.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (209 commits)
[POWERPC] Create add_rtc() function to enable the RTC CMOS driver
[POWERPC] Add H_ILLAN_ATTRIBUTES hcall number
[POWERPC] xilinxfb: Parameterize xilinxfb platform device registration
[POWERPC] Oprofile support for Power 5++
[POWERPC] Enable arbitary speed tty ioctls and split input/output speed
[POWERPC] Make drivers/char/hvc_console.c:khvcd() static
[POWERPC] Remove dead code for preventing pread() and pwrite() calls
[POWERPC] Remove unnecessary #undef printk from prom.c
[POWERPC] Fix typo in Ebony default DTS
[POWERPC] Check for NULL ppc_md.init_IRQ() before calling
[POWERPC] Remove extra return statement
[POWERPC] pasemi: Don't auto-select CONFIG_EMBEDDED
[POWERPC] pasemi: Rename platform
[POWERPC] arch/powerpc/kernel/sysfs.c: Move NUMA exports
[POWERPC] Add __read_mostly support for powerpc
[POWERPC] Modify sched_clock() to make CONFIG_PRINTK_TIME more sane
[POWERPC] Create a dummy zImage if no valid platform has been selected
[POWERPC] PS3: Bootwrapper support.
[POWERPC] powermac i2c: Use mutex
[POWERPC] Schedule removal of arch/ppc
...
Fixed up conflicts manually in:
Documentation/feature-removal-schedule.txt
arch/powerpc/kernel/pci_32.c
arch/powerpc/kernel/pci_64.c
include/asm-powerpc/pci.h
and asked the powerpc people to double-check the result..
Disable auto-select of CONFIG_EMBEDDED. ELECTRA_IDE selects
PATA_PLATFORM which should be sufficient.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename the pasemi platform to "pasemi" to be in line with the
platform's directory name.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support to build the PS3 flash rom image and remove some unneeded
lmb calls.
The PS3's lv1 loader supports loading gzipped binary images from flash
rom to addr zero. The loader enters the image at addr 0x100.
In this implementation a bootwrapper overlay is use to arrange for the
kernel to be loaded to addr zero and to have a suitable bootwrapper
entry at 0x100. To construct the rom image, 0x100 bytes from offset
0x100 in the kernel is copied to the bootwrapper symbol
__system_reset_kernel. The 0x100 bytes at the bootwrapper symbol
__system_reset_overlay is then copied to offset 0x100. At runtime the
bootwrapper program copies the 0x100 bytes at __system_reset_kernel to
addr 0x100.
zImage.ps3 is a wrapped image that contains a flat device tree, an lv1
compatible entry point, and an optional initrd. otheros.bld is the gzip
compresed rom image built from zImage.ps3. otheros.bld is suitable for
programming into the PS3 boot flash memory.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert the semaphores in low_i2c that are used as mutexes to real
mutexes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The struct device_node currently has a _flags variable, although
it's only used for one flag - OF_DYNAMIC. Generalise the flag
accessors so we can use them with other flags in future.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds support for PowerQuicc on-chip PCMCIA. The driver is implemented as
of_device, so only arch/powerpc stuff is capable to use it, which now implies
only mpc885ads reference board.
To cope with the code that should be hooked inside driver, but is really board
specific (like set_voltage), global structure mpc8xx_pcmcia_ops holds
necessary function pointers that are filled in the BSP code.
[akpm@linux-foundation.org: whitespace diddles]
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
sparse caught these static functions / __iomem annotations
under arch/powerpc/platform/52xx/
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add 831x USB platform setup code and rework 834x USB platform setup code.
Move USB platform code to usb.c for different boards with CPU of the same
series to share the USB initialization code.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove redundant pci_read_irq_line() function for 85xx CDS board.
This function has been realized in common ppc pci code.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make the interrupt numbers match the OpenPIC spec intead of the
Freescale docs which distinguish between internal and external interrupts.
Now we can use the interrupt number directly to find the register offset
associated with it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Begin with MPC8548 a new reset control register is added that asserts
HRESET_REQ to board logic.
This register is used for chip reset.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The function backing_ops->read_mfc_tagstatus() doesn't return a
correct value because the dma_tagstatus_R register isn't saved in
CSA. This fixes the problem.
Signed-off-by: Kazunori Asayama <asayama@sm.sony.co.jp>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When waiting for I/O events on mfc in an SPU context by using
poll/epoll syscalls, some of the events can be lost because of wrong
order of poll_wait and MFC status checks in the spufs_mfc_poll
function and non-atomic update of tagwait. This fixes the
problem.
Signed-off-by: Kazunori Asayama <asayama@sm.sony.co.jp>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
spu_activate can be called from multiple threads at the same time on
behalf of the same spu context. We need to make sure to only add it
once to avoid runqueue corruption.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Only enable the scheduler tick if we have any context waiting to be
scheduled.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We're currently too permissive with counting libassist calls - fix the
check on the SPE stop-and-signal status.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Provide load average information for spu context. The format
is identical to /proc/loadavg, which is also where a lot of code
and concepts is borrowed from.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The new tid file contains the ID of the thread currently running the
context, if any. This is used so that the new spu-top and spu-ps
tools can find the thread in /proc.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove redundant whitespace in arch/powerpc/platforms/cell/spufs/
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
spufs_dir_inode_operations is exactly the same as
simple_dir_inode_operations. Use that instead.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
And last but not least we need to make sure the scheduler tick never
preempts a nosched context.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
spu_deactivate should never be called for nosched contets. Put in
a check so we can print a stacktrace and exit early in case it
happes erroneously.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a cpus_allowed allowed filed to struct spu_context so that we always
use the cpu mask of the owning thread instead of the one happening to
call into the scheduler. Also use this information in
grab_runnable_context to avoid spurious wakeups.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update scheduling information on every spu_run to allow for setting
threads to realtime priority just before running them. This requires
some slightly ugly code in spufs_run_spu because we can just update
the information unlocked if the spu is not runnable, but we need to
acquire the active_mutex when it is runnable to protect against
find_victim. This locking scheme requires opencoding
spu_acquire_runnable in spufs_run_spu which actually is a nice cleanup
all by itself.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Print out a few scheduler tuning parameters when we've compiled
with DEBUG defined.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current timeslice code mixes 'jiffies' up with 'spesched ticks'. This
change correctly defines the number of time slices each SPE contexts is
given, and clarifies the comment.
This brings the default timeslice for SPE contexts into a reasonable
range.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable preemptive scheduling for non-RT contexts.
We use the same algorithms as the CPU scheduler to calculate the time
slice length, and for now we also use the same timeslice length as the
CPU scheduler. This might be not enough for good performance and can be
changed after some benchmarking.
Note that currently we do not boost the priority for contexts waiting
on the runqueue for a long time, so contexts with a higher nice value
could starve ones with less priority. This could easily be fixed once
the rework of the spu lists that Luke and I discussed is done.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Get rid of the scheduler workqueues that complicated things a lot to
a dedicated spu scheduler thread that gets woken by a traditional
scheduler tick. By default this scheduler tick runs a HZ * 10, aka
one spu scheduler tick for every 10 cpu ticks.
Currently the tick is not disabled when we have less context than
available spus, but I will implement this later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a bit define from book, and replace one hex number with a
symbol, for clarity.
Signed-off-by: Sebastian Siewior <bigeasy@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently it fails with gcc from sdk 2.1 because of a spec change [1].
Maybe we should start using the definitions from spu_mfcio.h.
[1] http://gcc.gnu.org/ml/gcc-patches/2006-11/msg01598.html
Signed-off-by: Sebastian Siewior <bigeasy@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent change to cell_defconfig to enable cpufreq on Cell exposed
the fact that the cbe_cpufreq driver currently needs the PMI interface
code to compile, but Kconfig doesn't make sure that the PMI interface
code gets built if cbe_cpufreq is enabled.
In fact cbe_cpufreq can work without PMI, so this ifdefs out the code
that deals with PMI. This is a minimal solution for 2.6.22; a more
comprehensive solution will be merged for 2.6.23.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the places we can move to using pci_bus_to_host, this allows us
to make pci_bus_to_host static and remove its export.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make the ppc32 pcibios_alloc_controller take a device node to match
the ppc64 prototypes and have it set arch_data.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make the pci_controller struct use global_number for the PHB domain number
instead of index to match what ppc64 does and reuse its pci_domain_nr code.
Introduced a pci-common.c to handle shared code between ppc32 & ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale PCI-e RC poses as a transparent bridge, but does not
implement the IO_BASE or IO_LIMIT registers in the config space. This
means that the code which initializes the bridge resources ends up
setting the IO resources erroneously. Add quick_fsl_pcie_transparent()
to handle this.
This change sets RC of mpc8641 to be a transparent bridge
for legacy I/O access and initializes the RC bridge resources
from the device tree.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Set IDE in ULI1575 to not 100% native mode, which forces
the IDE driver to probe the irq itself.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale PCI-e controllers have an issue in that they use the
PCI_PRIMARY_BUS register in the virtual P2P bridge to determine which
bus number to match on when generating a type 0 config cycle. The
issue is if we are renumbering bus numbers to match Linux we will try
setting the PCI_PRIMARY_BUS and will not know which bus number to use
for generating type 0 config cycles. We surpress writing the register
in the P2P bridge and always keep it at zero.
In the future when proper PCI domain support is working we should be
able to remove this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We check the Link Training and State Status register to make sure we
are at least at the L0 state.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove errata for PCI-e support of Rev 1.0 of MPC8641 since its considered
obselete and is not production level silicon from Freescale.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed the remants of bus_offset and use self_busno in the mv64x60 case
and use pci_assign_all_buses on 83xx/85xx.
83xx/85xx have multiple PHBs and the firmwares on these devices tend not
to handle topologies with P2P bridges well so we let Linux just reassign
the bus numbers to match.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The user of the fsl_pcie code doesn't set bus_offset and 82xx doesn't
require it either. Remove the places in the code that reference it so
we can remove it all together.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that we have the pci_controller in the exclude function we can easy
figure out if the bus number is the PHB or not. The old style of using a
variable setup at init time was actually broken and would only work in
specific cases.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are times that we need to know which controller we are on to decide
how to exclude devices properly. We now pass the pci_controller that we
are going to use down to the pci_exclude_device function. This will
greatly simplify being able to exclude the PHBs in multiple controller
setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The hose->bus_offset is only used for PCI config cycles and the 52xx PCI
config code doesn't actually ever set bus_offset to a non-zero value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale and Marvell PCI controllers dont require explicit setting for
type 1 config cycles. They handle producing them by implicitly looking at the
bus, devfn.
The TSI108 and 52xx don't use the generic PCI indirect code and thus don't
bother with set_cfg_type.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The TSI108 code and the 32 bit powermac and chrp platforms
have dependency on PCI that is not easy or desirable to get rid
of.
The easiest fix is to always select CONFIG_PCI if one of those
platforms is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When CONFIG_PCI is disabled, the definitions for isa_io_base,
isa_mem_base and pci_dram_offset are entirely unused, but they
can result in link failure because they are defined in multiple
places.
The easiest fix is to just remove all these definitions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Many platforms currently define their own add_bridge function, some
of them globally. This breaks some multiplatform configurations.
Prefixing each of these functions with the platform name avoids
this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cores used in the MPC82xx/83xx/86xx embedded controllers are very similar
to those in the 32 bit general-purpose processors, so it makes sense to
treat them as the same CPU family.
Choosing between the embedded platforms and the multiplatform code is
now done in the platform menu, but functionally everything stays the
same.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently iSeries will recalibrate the cputime_factors in the first
settimeofday() call.
It seems the reason for doing this is to ensure a resaonable time delta after
time_init(). On current kernels (with udev), this call is made 40-60 seconds
into the boot process, by moving it to a late initcall it is called
approximately 5 seconds after time_init() is called. This is sufficient to
recalibrate the timebase.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for storage devices to the device probe code.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add storage driver core support for the PS3.
PS3 storage devices are a special kind of PS3 system bus device.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Preallocate 256 KiB of bootmem memory for the PS3 FLASH ROM storage driver.
This can be disabled by passing `ps3flash=off' on the kernel command line.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PS3 uses the kernel's hotplug memory support, so make sure it is
always enabled when building for PS3.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace the inline asm with bitops in the PS3 interrupt
chip mask routines.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename the PS3 static symbols node to ppe_id and cpu to thread_id
to clarify usage.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add routines to probe devices present on the system
and to register those devices with the LDM.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert the ps3fb device from a platform device to a PS3 system bus device.
Fix the remove and shutdown methods to support kexec and to make ps3fb a
loadable module.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3 vuart updates to reflect the new PS3 unified device support.
- Move vuart devices to the PS3 system bus.
- Replace use of ps3_vuart_port_device with ps3_system_bus_device.
- Make the PS3 vuart bus driver a loadable module.
- Add remove() and shutdown() routines.
- Move ps3_vuart_work into ps3_vuart_port_priv.tx_list.
- Remove redundant spinlock ps3_vuart_work.lock.
- No longer free ps3_vuart_port_device.priv on shutdown.
- Cleanup Kconfig defs.
- Export symbols needed for modular port drivers.
- Arrange to use port numbers found in repository.
- Fix bugs in ps3_vuart_read_async() and polled reading
- Cleanup handling of shared interrupt with ps3_vuart_bus_interrupt_get()
and ps3_vuart_bus_interrupt_put()
- Add more comments to vuart.c.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Repository updates:
- Extract ps3_repository_find_bus() from ps3_repository_find_device(), as the
storage driver needs it.
- Make ps3_repository_find_device() return -ENODEV if a device is not found,
just like if a bus is not found.
- Add ps3_repository_read_vuart_sysmgr_port() and
ps3_repository_read_vuart_av_port() to get vuart port info.
- Add device enumeration routines ps3_repository_find_device() and
ps3_repository_find_devices().
- Cleanup debug routines.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add modinfo attribute to ps3_system_bus devices. Also make them all
children of the same ps3_system_bus 'device' so they appear in a
corresponding subdirectory under /sys/devices.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To allow userspace to automatically load modules, we need to hook up
uevent for ps3_system_bus devices. I've used the form 'ps3:%d' with
the ps3_match_id, since that's what we use for matching drivers.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rework the PS3 system bus to unify device support.
- DMA region sizes must be a power of two
- storage bus DMA updates:
- Small fixes for the PS3 DMA core:
o fix alignment bug
o kill superfluous test
o indentation
o spelling
o export ps3_dma_region_{create,free}()
- ps3_dma_region_init():
o Add `addr' and `len' parameters, so you can create a DMA region that
does not cover all memory (use `NULL' and `0' to cover all memory).
This is needed because there are not sufficient IOMMU resources to have
all DMA regions cover all memory.
o Uninline
- Added remove and shutdown routines to all drivers.
- Added loadable module support to all drivers.
- Added HV calls for iopte management (needed by sound driver).
Signed-off-by: MOKUNO Masakazu <mokuno@sm.sony.co.jp>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixup the core platform parts needed for kexec to work on the PS3.
- Setup ps3_hpte_clear correctly.
- Mask interrupts on irq removal.
- Release all hypervisor resources.
- Create new routine ps3_shutdown_IRQ()
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This just moves the definitions of the PS3 chip_mask routines up
above the irq setup routines. This change is needed for the
kexec updates that follow. Also adds some inline documentation
to the routines.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix some PS3 build warnings reported by `make C=1'. You need to
install sparse:
git://git.kernel.org/pub/scm/devel/sparse/sparse.git
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use ioremap_flags() to map SPU regions as non-guarded.
Change the use of _ioremap() to ioremap_flags().
CC: Arnd Bergmann <arnd.bergmann@de.ibm.com>
CC: Masato Noguchi <Masato.Noguchi@jp.sony.com>
CC: Takao Shinohara <shin@sm.sony.co.jp>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the PS3 debug routines from using the GCC specific
'__attribute__ ((unused))' to the preprocessor macro
__maybe_unused.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename the PS3 static symbol virqs to ps3_ipi_virqs to aid in
debugging.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a shutdown method to spu_sysdev_class to allow proper spu resource
cleanup on system shutdown. This is needed to support kexec on the PS3
platform.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Power machines supporting VRMA, Kexec/Kdump does not work.
VRMA (virtual real-mode area) means that accesses with IR/DR = 0
(i.e. the MMU "off") actually still go through the hash table,
using entries put there by the hypervisor.
This means that when we clear out the hash table on kexec, we need to
make sure these entries are left untouched.
This also adds plpar_pte_read_raw() on the lines of
plpar_pte_remove_raw().
Signed-off-by : Sachin Sant <sachinp@in.ibm.com>
Signed-off-by : Mohan Kumar M <mohan@in.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In some of the PPC970 based systems, interrupt would be distributed to
offline cpus also even when booted with "maxcpus=1". So check whether
cpu online map and cpu present map are equal or not. If they are equal
default_distrib_server is used as interrupt server otherwise boot cpu
(default_server) used as interrupt server.
In addition to this, if an interrupt is assigned to a specific cpu (ie
smp affinity) and if that cpu is not online, the earlier code used to
return the default_distrib_server as interrupt server. This
introduces an additional parameter to the get_irq function, called
strict_check. Based on this parameter, if the cpu is not online
either default_distrib_server or -1 is returned.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
