- Fix the I2C address and supply line names for the AK8974
- Sets up the interrupt lines to the different components as they
actually are connected, I was confused for some time by the fact
that several lines were connected with <NM> 0 Ohm resistors, which
means NOT MOUNTED and is thus not 0 Ohm at all but infinite ohms,
i.e. not connected at all.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
as well as i2s and ethernet support on rk3228/rk3229 devices
and a dts file for the rk3229 eval board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXdbKVAAoJEPOmecmc0R2B4t8H/3J/l3fXyAskseN12883GkgO
WxEaCe4LeLbxp9Lcd3jmhXM4WZKPbfngYdLvL6kNh/LZeZT3naa2B55ot0FiIOHQ
PVvAC9ce7T0wTeK/aC2iFU6two6ZMbk8jSRfpfpijHIwK9U1NQcXTssuzvHR+S/L
+QP29M2TP3Y9UrPydx8kpCeH0kav2WmdqNmRdpQ9hokCqAiR2jbXi2N4PNtVl9v9
Vy/s+kFa8RSLzWTUICalwrMzS7j/VyeFKq61NPPjVdfS0Q+poCcdaDw5ZPEtZYBu
eerD1hTou+z7MPz6F5SM3J5U9G8NEp0NO4b3C0eWvAuA9cMv0smJFfqVD4erp40=
=wEmr
-----END PGP SIGNATURE-----
Merge tag 'v4.8-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Audio support and spi-flash on rk3288-veyron Chromedevices
as well as i2s and ethernet support on rk3228/rk3229 devices
and a dts file for the rk3229 eval board.
* tag 'v4.8-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add support rk3229 evb board
ARM: dts: rockchip: add GMAC nodes for RK322x SoCs
ARM: dts: rockchip: add i2s nodes for RK322x SoCs
ARM: dts: rockchip: rename rk3228.dtsi to rk322x.dtsi
clk: rockchip: add clock-ids for rk3228 MAC clocks
clk: rockchip: add clock-ids for rk3228 audio clocks
ARM: dts: rockchip: rename i2s model for Veyron devices
ARM: dts: rockchip: move rk3288 io-domain nodes to the grf
ARM: dts: rockchip: Enable analog audio on rk3288-veyron chromebooks
ARM: dts: rockchip: Add shared file for audio on rk3288-veyron boards
ARM: dts: rockchip: add SPI flash node for rk3288-veyron
Signed-off-by: Olof Johansson <olof@lixom.net>
This allows to switch the card signal voltage level to 1.8 V, which is
needed for any ultra high speed modes to work.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Use APMU on R-Car Gen2 and provide SMP for r8a7793 SoC
* Update console parameters to uniformly use chosen/stdout-path,
serial0, not provide kernel unnecessary command line parameters
* Add DU pins to silk board
* Add support for blanche/r8a7792
* Name pfc subnodes after device name
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gmxg
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.8
* Use APMU on R-Car Gen2 and provide SMP for r8a7793 SoC
* Update console parameters to uniformly use chosen/stdout-path,
serial0, not provide kernel unnecessary command line parameters
* Add DU pins to silk board
* Add support for blanche/r8a7792
* Name pfc subnodes after device name
* tag 'renesas-dt2-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (41 commits)
ARM: dts: r8a7792: add SMP support
ARM: dts: r8a7793: Add APMU node and second CPU core
ARM: dts: r8a7791: Add APMU node
ARM: dts: r8a7790: Add APMU nodes
devicetree: bindings: Renesas APMU and SMP Enable method
ARM: dts: kzm9g: Update console parameters
ARM: dts: kzm9d: Update console parameters
ARM: dts: marzen: Add serial port config to chosen/stdout-path
ARM: dts: genmai: Update console parameters
ARM: dts: armadillo800eva: Update console parameters
ARM: dts: r8a7792: add JPU support
ARM: dts: r8a7792: add JPU clocks
ARM: dts: silk: add DU pins
ARM: dts: blanche: add Ethernet support
ARM: dts: blanche: initial device tree
ARM: dts: blanche: document Blanche board
ARM: dts: r8a7792: add IRQC support
ARM: dts: r8a7792: add [H]SCIF support
ARM: dts: r8a7792: add SYS-DMAC support
ARM: dts: r8a7792: initial SoC device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This device uses BCH-1 instead of BCH-8. This fixes ECC errors and makes
NAND usable with brcmnand.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Using separated file with common chip select parameters will allow us
adding other ECC setups without code duplication.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds the Cirrus Logic EP7209,EP7211 DT templates and support for
EDB7211 Development board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- add dts files for Hi3519
- shuffle ARCH_HIGHBANK, ARCH_HISI, ARCH_HIX5HD2 and ARCH_HIP0X
around to keep the list sorted
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Replace hardcoded reserved memory ranges with auto-allocated ones
and enable MFC for all boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sS8p
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-exynos-mfc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Topic branch for Exynos MFC changes for v4.8, part 2:
Replace hardcoded reserved memory ranges with auto-allocated ones
and enable MFC for all boards.
* tag 'samsung-drivers-exynos-mfc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: enable MFC device for all boards
ARM: dts: exynos: move MFC reserved memory regions from boards to .dtsi
ARM: dts: exynos: replace hardcoded reserved memory ranges with auto-allocated ones
ARM: dts: exynos: Enable MFC device on Exynos4412 Odroid boards
ARM: dts: exynos: Convert MFC device to generic reserved memory bindings
ARM: EXYNOS: Remove code for MFC custom reserved memory handling
media: s5p-mfc: add iommu support
media: s5p-mfc: replace custom reserved memory handling code with generic one
media: s5p-mfc: use generic reserved memory bindings
of: reserved_mem: add support for using more than one region for given device
media: set proper max seg size for devices on Exynos SoCs
media: vb2-dma-contig: add helper for setting dma max seg size
s5p-mfc: Fix race between s5p_mfc_probe() and s5p_mfc_open()
s5p-mfc: Add release callback for memory region devs
s5p-mfc: Set device name for reserved memory region devs
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a series of dtc warning fixes when compiled with make W=2
from Javier Martinez Canillas <javier@osg.samsung.com>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ikLv
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.8/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of device tree updates for omaps for v4.8 merge window.
This is a series of dtc warning fixes when compiled with make W=2
from Javier Martinez Canillas <javier@osg.samsung.com>.
* tag 'omap-for-v4.8/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (27 commits)
ARM: dts: am57xx: sbc-am57x: remove unneded unit name
ARM: dts: omap5-board-common: remove unneded unit names
ARM: dts: omap5-cm-t54: remove unneded unit names and add reg properties
ARM: dts: am437x: cm-t43: remove unneded unit names
ARM: dts: am437x-gp-evm: remove unneded unit name
ARM: dts: am43xx-epos-evm: remove unneded unit name
ARM: dts: omap4-var-om44customboard: remove unneded unit name
ARM: dts: omap4-sdp: remove unneded unit names
ARM: dts: omap4-panda-common: remove unneded unit names
ARM: dts: omap4-duovero-parlor: remove unneded unit name
ARM: dts: omap3-thunder: remove unneded unit name
ARM: dts: sbc-t3x30: remove unneded unit names
ARM: dts: omap3-pandora-common: remove unneded unit name
ARM: dts: omap3-overo-common-dvi: remove unneded unit names
ARM: dts: omap3-igep0020-common: remove unneded unit names
ARM: dts: omap3: overo: remove unneded unit names in display nodes
ARM: dts: omap3-ha-lcd: remove unneeded unit name
ARM: dts: omap3-gta04: remove unneeded unit names
ARM: dts: omap3-devkit8000-lcd-common: remove unneeded unit names
ARM: dts: omap3-devkit8000: remove unneeded unit names
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add two i.MX23/STMP3780 based MP3 player device support, Creative
X-Fi3 and SanDisk Sansa Fuze+
- Add the support of Auvidea H100 device which is a SolidRun MicroSOM
baseboard
- Restructure i.MX7Dual DTS files to support i.MX7Solo and add Toradex
Colibri iMX7S/iMX7D boards
- Device additions and enabling for various boards: mmc device for
utilite-pro, IRQ controller and CAN support for TS-4800, display and
touchscreen support for imx7d-sdb, SAI audio and LCD support for
imx6ul-14x14-evk, gpio power off support for imx6q-bx50v3, etc.
- Update the boards from Freescale/NXP to use WDOG_B pin for reset
- PCI reset polarity correction for imx6qdl-sabresd and imx6q-tbs2910
- Update i.MX board dts files to use generic uart-has-rtscts DT
property instead of vendor specific one
- DTC warning fixing for a few boards which are mostly mismatch between
unit-address and reg property
- Remove SION setting from all mux modes on i.MX25
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXcmoVAAoJEFBXWFqHsHzOQfEH/1z78cIe4bBd61boOge5VGUc
BdVGC4U6vcB1cRxceA8sh6U8QVyDtnojB1r5C3W+Zad4VMIdptGwbxAJne268WTt
iSRY8+Mu81KgrvkQ4flosTp7w8J4DfzithMGzDnhq3vTFblaaAT63u9AcDlcSGCq
1p/wPpqUb7COEBYOAxcOfypIPkZXrcvTfHHm3KOAV+cvNEQHZ0n4kLDWfjFxiUgo
oE+RDTku2q7mfXs22QXCUyTLNlwzuczsQ35sPM4JbIc6JBVYyyF/tHQFB162MB7u
ELK79F4LKip4wUS8b52M3xEQWiB0Cb1jtymomHLdGzguk7FtaV18vSUvA918GB8=
=2NUH
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree update for 4.8:
- Add two i.MX23/STMP3780 based MP3 player device support, Creative
X-Fi3 and SanDisk Sansa Fuze+
- Add the support of Auvidea H100 device which is a SolidRun MicroSOM
baseboard
- Restructure i.MX7Dual DTS files to support i.MX7Solo and add Toradex
Colibri iMX7S/iMX7D boards
- Device additions and enabling for various boards: mmc device for
utilite-pro, IRQ controller and CAN support for TS-4800, display and
touchscreen support for imx7d-sdb, SAI audio and LCD support for
imx6ul-14x14-evk, gpio power off support for imx6q-bx50v3, etc.
- Update the boards from Freescale/NXP to use WDOG_B pin for reset
- PCI reset polarity correction for imx6qdl-sabresd and imx6q-tbs2910
- Update i.MX board dts files to use generic uart-has-rtscts DT
property instead of vendor specific one
- DTC warning fixing for a few boards which are mostly mismatch between
unit-address and reg property
- Remove SION setting from all mux modes on i.MX25
* tag 'imx-dt-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (47 commits)
ARM: dts: imx7: add Toradex Colibri iMX7S/iMX7D support
ARM: dts: imx7d: move input header into base device tree
ARM: dts: imx7d: recreate imx7d.dtsi with i.MX 7Dual specifics
ARM: dts: imx7d: use imx7s.dtsi as base device tree
ARM: dts: imx7d-sdb: Add support for touchscreen
ARM: dts: imx7d-sdb: Add display support
ARM: dts: imx7d: Add SPI support
ARM: dts: imx6q-bx50v3: Add gpio power off support
ARM: dts: imx6ul-pico-hobbit: Fix Ethernet PHY reset GPIO
ARM: dts: imx6q-tbs2910: fix pcie reset polarity
ARM: dts: imx6sx-sdb: Use WDOG_B pin reset
ARM: dts: imx6ul-evk: Use WDOG_B pin reset
ARM: dts: imx7d-sdb: Use WDOG_B pin reset
ARM: dts: imx6qdl-sabresd: Use WDOG_B pin reset
ARM: dts: utilite-pro: add mmc card slot support
ARM: dts: imx6q-cm-fx6: fix the operation points
ARM: dts: imx6qdl.dtsi: add "arm,shared-override" for pl310
ARM: imx25-pinfunc: remove SION from all modes
ARM: imx25-pinfunc: document SION being important for MX25_PAD_SD1_CMD__SD1_CMD
ARM: dts: ls1021a: Add dis_rxdet_inp3_quirk property to USB3 node
...
Signed-off-by: Olof Johansson <olof@lixom.net>
DT so that the firmware can tell us its MAC address.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCgAGBQJXea5HAAoJELXWKTbR/J7ofl4P/36ReBOwgWtXa2h/kDAU9cjM
lAaFedQ4GesRRPNkFboyO5YM05H1EnyVSmbJglpCRVsQI0STph/NXGmTH+tIN29L
iC/pJw1Nz1rQOhQDdDch5xhqC1lgfZ7g4PFmDuTJr9NTLFcOKQVsxSmBMqDZSbxC
bWrlUW6YdZBK7tUfK4lf6p9tAnpNeYyn3VGXPKb2l49DcwZfZgU6D28mmH4/PfHc
KB5cNUfEEE3wt6DtCB6cWsqwPlofwyz/62NP1kwotMFbFRrHmraVVkR08OdrfxwJ
I2Q/tD+ztc8/FQq5hQYHfxSX9RXNmRutrRZYJlT6hwPAAue91uy9r9jYMCl6hwm3
7zG32GU7SL8mqUdYLjVnZ6H8vqc7+GUf0hdz46vnXDLwquawWMmOory7PX1fgXJc
pLiaUtfRvYd2RmMSsbm7QCdQu1yQ93Q3ytcAJsDCq2fJ+ySMpHWgQ+El3yRKmnIk
fr4c5e1qqMutEfbl4hirU8Dg9dx0KbQDoY3L1e+sRQRSy9YppRHD2Lw3pOKlY3X6
NUUvvoAfjDwDHNCJQAi2n9FRxlhhrUNynFlGfsjXXDOZHtFpOGC4zOEgMXr2uMNm
r1qYNiB03vhYVHFfUsNDtD8LSmSQ3FEmMMvL4fhKjRsjYuLHccPs7H5l+Oq45OH0
OndYBA60urgkG2QnonR3
=byP6
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXfH8AAAoJEIfQlpxEBwcE0zoP/1kuAYK43BkVAvQzDaA154tR
W5kV89q4VwhfQ+q+XkCkqljPFZzAPhhr6BA0D4gcVzGTvrCSWroL+yAl+D04Pyi0
oDmxk/KCvDblsAg87he/OQSKrKVeBYeOiLwvO48LzFWbLd4JFxAOhCTAGNsDAWkl
QMIWH+dbbB2ql9J1X1qP7nHkejIDG4Sb8ti88NKyKNlGsS0rVNFW9RXEXmBQPNVp
PEbraANLWP99gtv1ASomAWcAXglR0TJTtucB8oCZ47cJ5/Cgkv1q+sbIHl9dPwbX
iFze27hzIhd0bP1PvHnjy1yjYmWhYRcN8UBqn5kx+73keF3LvhoThwPagcifFfsJ
ZAk5/LF20rc3D92ucYQHq9EaCrQ5rlCOnFWW4MZY48fj1nIKTguw9NJruKMHEWli
DfnxJSYNeHJq9oMFPpwyblWlQyF/snIwOtKUFJmKC3Zdls1G0qw400COrvi7E1y6
FNCqxF8ueoV3eHrVoreylJqPYa1HYJ2K2nYkUhHyu3Jn3+fRUvCwedNcupsx3XJI
CdyxoANsA9NPzxbOW5bXRfuhMGk/NPR307Wp7bFcupjPgT7IWOG9rr7cE9MYnvjj
xGuhWCeyH1h9nUsv/UOxoW0qKIY7oTfXdW93xQ8ERs/eM6J4rg/1+K2KjFFxYqQX
+w97VoUBS/w2grkrpmh2
=AyiN
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-dt-next-2016-07-03' into devicetree/next
This pull request brings in the change to describe the ethernet in the
DT so that the firmware can tell us its MAC address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Two patches fixing simplefb on the SoCs that had their display clocks
enabled, and one fix for the CHIP that will enable its sched clock.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tU7Y
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.7' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Pull "Allwinner Fixes for 4.7" from Maxime Ripard:
Two patches fixing simplefb on the SoCs that had their display clocks
enabled, and one fix for the CHIP that will enable its sched clock.
* tag 'sunxi-fixes-for-4.7' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun7i: Fix pll3x2 and pll7x2 not having a parent clock
ARM: dts: sunxi: Add pll3 to simplefb nodes clocks lists
ARM: sunxi/dt: make the CHIP inherit from allwinner,sun5i-a13
The auxtek t004 has its otg usb vbus hardwired to 5v (likely in case
people use it to power the board instead of the dedicated power micro
usb connector), it does have an id pin, so it allows full otg
functionality.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- PWM binding updates and related dts changes
- OCM RAM updates for dra7
- Enable n900 lirc-rx51 driver
- omap3-gta04 updates for backlight, bma180, itg3200, hmc5843 and wifi
- am335x, am437x and am57xx operating point updates and additions
- am335x-icev2 pca9536 node
- dra72-evm regulator updates
- edma spelling fixes
- am335x and am437x ethernet phy update
- a series of mcbsp updates
- omap3-gta04 eeprom
- dra7 PCIe unit address fix
- stdout-path for beaglebone variants
- crypto accelerator nodes for am335x, am437x and dra7
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXam0sAAoJEBvUPslcq6VzYewP/imm4it6lqwtsfNthtmSW/Qi
PO6XyZ/j8ayRcddsrnjTPFLH8/fPaIkKxI2eCQZpe+rHhK6Ifg2lGrZonJS7pHmu
6NqRe0OkUHw3EIRuHW0uP4OCzYnyinJf0A7jp1nuQq5CBH8rzqHS7xyNEBryeKMQ
rScauNPU+Z+/LM0Qz2mpYAAwWnJHlT/K8Pok+JoB16TiHsiNbhXoQlSwB1bDe+b6
5Ssz42AG68rp9dGJ8SnbY25qBwQc1oBZeE21ItHTMwfUlAeQiG4nxejzqYaPISQw
Aj/5Q0+qYp8aiCbQXaYrt0+Tz7UBfFTK3xIuw3011P48SaJAVbTe3tjPbZuORZng
RvUHtavk2hEAoHQfU9gRYFPHt9uNLZqGU8gTmILLL/Go9oPENeQeOmEPPMtDC2eu
nBOa1ROsAsXPBKTWJrpDRCaH7i5W4md4U9mo8LCG2iCXVrPHXXnWoRWGiUchiMzm
ykPK9ynL+CwQ6M5dHFhW4rsnDZdrG2v5YAVDdhLnCnl9MrIFINTNLA/6Axz+xq4/
8B+ymUyW9ymrxeoxEQpCbFWHg3UfN0B97r1JUy1D8wDdfberGHM35FspkESEjEeP
PYOcrk0zx1wbVOBhEthvwInPX72T870xyDyCgl7Y2ayp6upTMQXL6C3uK4DR4W1p
TO/qrewNdyK5iA+FWtYr
=2xdp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.8/dt-part1-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.8 merge window:
- PWM binding updates and related dts changes
- OCM RAM updates for dra7
- Enable n900 lirc-rx51 driver
- omap3-gta04 updates for backlight, bma180, itg3200, hmc5843 and wifi
- am335x, am437x and am57xx operating point updates and additions
- am335x-icev2 pca9536 node
- dra72-evm regulator updates
- edma spelling fixes
- am335x and am437x ethernet phy update
- a series of mcbsp updates
- omap3-gta04 eeprom
- dra7 PCIe unit address fix
- stdout-path for beaglebone variants
- crypto accelerator nodes for am335x, am437x and dra7
* tag 'omap-for-v4.8/dt-part1-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
ARM: dts: AM43xx: Add node for RNG
ARM: dts: AM43xx: clk: Add RNG clk node
ARM: dts: DRA7: Add DT node for RNG IP
ARM: dts: DRA7: Add support for SHA IP
ARM: dts: DRA7: Add DT nodes for AES IP
ARM: dts: DRA7: Add DT node for DES IP
ARM: dts: am335x-bone-common: use stdout-path in Beaglebone boards.
ARM: dts: DRA7: fix unit address of second PCIe instance
ARM: dts: omap3-gta04: Add RFID eeprom node
ARM: dts: omap4-duovero: Add pdmclk binding for audio
ARM: dts: omap4-var-som-om44: Add pdmclk binding for audio
ARM: dts: omap4-sdp: Add pdmclk binding for audio
ARM: dts: omap4-panda-common: Add pdmclk binding for audio
ARM: dts: omap5-board-common: Add pdmclk binding for audio
ARM: dts: omap3: Add clocks to McBSP nodes
ARM: dts: am335x-bone-common: Mark MAC as having only one PHY
ARM: dts: am437x-idk-evm: Mark MAC as having only one PHY
ARM: dts: Correct misspelling, "emda3" -> "edma3"
ARM: dts: dra72-evm: Rename 3.3V regulator tag
ARM: dts: am335x-icev2: Add DT node for TI PCA9536
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- New board: at91sam9260ek
- Fixes for the sam9_l9260
- Sama5d2 Xplained PMIC fix
- Addition of the PMU node for the sama5d2
-----BEGIN PGP SIGNATURE-----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=F38N
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.8-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT Changes for 4.8 #2:
- New board: at91sam9260ek
- Fixes for the sam9_l9260
- Sama5d2 Xplained PMIC fix
- Addition of the PMU node for the sama5d2
* tag 'at91-ab-4.8-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: sama5d2_xplained: Update the pmic node
ARM: dts: at91: sama5d2: add PMU node
ARM: dts: at91: sam9_l9260: Modify information in LED nodes.
ARM: dts: at91: sam9_l9260: Add pinctrl information to ethernet node.
ARM: dts: at91: add at91sam9260ek board DT
Signed-off-by: Olof Johansson <olof@lixom.net>
In order to be able to properly generate its pixel clock, the pll3-2x fixed
factor needs to be able to change the PLL3 rate too.
Add the needed extra compatible so that it behaves that way.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds all the mod1 clocks available on A20 to its device
tree. This list was created by looking at the A20 user manual.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The a10s mk802 uses a rtl8189es sdio wifi chip, add a node enabling
the mmc1 controller, this enables using the wifi chip (together with
an out of tree sdio driver for it).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the axp152 pmic to the mk802 dts, note there are
no regulator nodes as we do not yet support the regulators on the
axp152.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg controller, the id pin is not connected so enable
it in peripheral only mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have a proper binding for Ethernet switches hanging off
different buses, and a driver for the BCM53125 switch, add its Device
Tree as a child MDIO node, at MDIO address 30 (Broadcom pseudo-PHY
address) and describe the ports layout of the Lamobo R1 board.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The early A13 Q8 tablets all use a Realtek WiFi module connected to
USB1. The module is powered by AXP209's LDO3 at 3.3V.
Move the related settings from sun5i-a13-q8-tablet.dts to
sun5i-q8-common.dtsi, for all q8-based tablets.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the Bananapi M1 Plus A20 development board from
sinovoip.com.cn . This board is nearly a clone of the Lemaker's
Bananapro, but differ with the wlan chipset connection and i2s pinout.
And I also enable the integrated audio codec on default.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some of the sun8i q8 boards have an usb wifi controller, on other
variants this will result in an used usb root-hub, but the best
way to deal with wifi on this boards is to simply let the kernel
auto-detect usb or sdio wifi controllers.
This has been tested on an a23 based q8 tablet with a RTL8188ETV wifi
controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the mmc nodes above the ohci nodes for proper ordering by name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the &pio node below the mmc nodes for proper ordering by name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add NAND Flash controller node definition to the A20 SoC.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add NAND Flash controller node definition to the A10 SoC.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add pmic / regulator nodes to Mele M9 dts.
Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add pmic / regulator nodes to Mele A1000G quad dts.
Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The blue led on the Mele M9 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".
Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.
This renames the led from m9:blue:usr to m9:blue:pwr and marks
it as default on, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The blue led on the Mele A1000 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".
Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.
This renames the led from m9:blue:usr to a1000g:blue:pwr (fixing a copy
and paste error in the prefix while at it) and marks it as default on,
fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The blue led on the Mele A1000 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".
Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.
This renames the led from a1000:blue:usr to a1000:blue:pwr and marks
it as default on, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The Polaroid mid2809pxe04 tablet uses an sdio esp8089 wifi chip, so
ehci0 is not used and should be disabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we've all the necessary bits in place we can enable
full otg support on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we've all the necessary bits in place we can enable
full otg support on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the drivebus regulator which is an (optional)
part of the axp221/axp223 pmic. Since this regulator may not be
available at all depending on the board, mark it as disabled by
default.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the (optional) usbpower-supply of the
axp221 / axp223 pmic.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Use of these as regulators conflicts with use of the gpio pins as
gpios, so disabled the ldo_io# regulators by default, this avoids
the regulator core touching them when the pins are used as gpios.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Update the simplefb nodes for hdmi / tv-encoder out to point to
tcon0_ch1 instead of tcon0_ch0 as tcon clock.
While at it fix the clocks lines being longer than 80 chars.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Update the simplefb nodes for hdmi / tv-encoder out to point to
tcon0_ch1 instead of tcon0_ch0 as tcon clock.
While at it fix the clocks lines being longer than 80 chars.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It seems that recent kernels have a shorter timeout when scanning for
ethernet phys causing us to hit a timeout on boards where the phy's
regulator gets enabled just before scanning, which leads to non working
ethernet.
A 10ms startup delay seems to be enough to fix it, this commit adds a
20ms startup delay just to be safe.
This has been tested on a sun4i-a10-a1000 and sun5i-a10s-wobo-i5 board,
both of which have non-working ethernet on recent kernels without this
fix.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sunxi-common-regulators.dtsi provided dummy regulators vcc3v0, vcc3v3,
vcc5v0. 3.0V/3.3V and 5.0V are commonly used voltages in Allwinner
devices. These dummy regulators provide a stand-in when bindings that
require one, but the real regulator is not supported yet.
Since these are no longer needed, we can drop the include file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sunxi-common-regulators.dtsi provided dummy regulators vcc3v0, vcc3v3,
vcc5v0. 3.0V/3.3V and 5.0V are commonly used voltages in Allwinner
devices. These dummy regulators provide a stand-in when bindings that
require one, but the real regulator is not supported yet.
Since these are no longer needed, we can drop the include file by
copying over reg_usb1_vbus.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It seems that the wifi chip is powered by both ldo3 and ldo4 tied
together and that using only one results in the wifi-chip dropping of
the USB bus sometimes.
Ideally we would have a proper way of modelling this (this is being
worked on), but currently we do not. This is not an issue since we need
to keep these regulators always-on anyways, due to these boards
crashing when ldo3/4 get turned back on after having been turned off.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The BPI-M2+ is an H3 development board. It is a smaller form factor than
the original BPI-M2, with the new H3 SoC.
It has 1GB DRAM, 8GB eMMC, a micro SD card slot, HDMI output, 2 USB
host connector and 1 USB OTG connector, an IR receiver, WiFi+BT based
on Ampak AP6212.
The board also has a 3 pin header for (debug) UART, a 40 pin GPIO header
based on the Raspberry Pi B+, but the peripheral signals are not the
same, and an FPC connector for connecting BPI's camera.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move uart0 pins to sort the list of pin settings in alphabetical order.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is connected
to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is
connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP809 PMIC is used with the Allwinner A80 SoC, along with
an AXP806 PMIC as a slave.
This patch adds a dtsi file for all the common bindings and default
values unrelated to board design. Currently this is just listing all
the regulator nodes. The regulators are initialized based on their
device node names.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
spi2 is available on the UEXT connector
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
[Maxime: Fixed the node order]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Q8 form factor A13 tablets have a 7" LCD panel. Unfortunately we
don't know the exact model of the panel. Just pick a panel with
display timings close to what we know.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Q8 tablets use the audio codec to provide audio output via a
headphone jack or a small mono speaker. A GPIO output is used to
control speaker amp.
The tablets may or may not have an internal microphone.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A13 Q8 tablets, the PMIC's USB power supply (VBUS) is connected
to the external OTG port. This can be used to provide power and OTG VBUS
sensing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The output pin of LDO is also a GPIO pin, and the on/off settings of the
regulator are actually pinmux settings.
Disable it by default so it doesn't conflict with GPIO usage.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most of the display engine is shared between the R8 and the A13. Move the
common parts to the Á13 DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The RGB bus can be used in several configurations, one of which being the
RGB666.
Add a pinctrl group for that case.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the display and TCON clocks that are needed to drive the display
engine, tcon and TV encoders.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the display and TCON clocks that are needed to drive the display
engine, tcon and TV encoders.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Due to introducing the new driver - ACT8945A MFD drive,
change the pmic device node to align with the ACT8945A
regulator and charger drivers.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add power led node and rename status led node.
Signed-off-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Reviewed-by: Vijay Kumar B. <vijaykumar@bravegnu.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add missing pinctrl information to ethernet node.
Signed-off-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Reviewed-by: Vijay Kumar B. <vijaykumar@bravegnu.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add Device Tree source file for at91sam9260ek board. This official Atmel
Evaluation Kit is designed around a SoC based on a ARM 926 core the
at91sam9260.
The board is also added to the dts Makefile.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add the device tree nodes for the Advanced Power Management Unit (APMU)
and the second Cortex-A15 CPU core.
Use the "enable-method" prop to point out that the APMU should be used
for the SMP support.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DT nodes for the Advanced Power Management Unit (APMU) and the
second CPU core. Use the enable-method to point out that the APMU
should be used for SMP support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the Advanced Power Management Units (APMU), and use
the enable-method to point out that the APMU should be used for SMP
support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the Advanced Power Management Units (APMU), and use the
enable-method to point out that the APMU should be used for SMP
support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC4 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameters from the kernel command line, as they're
no longer needed for DT-based platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a "serial1" alias for the serial console (it is labeled "uart1").
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameter from the kernel command line, as it's no
longer needed for DT-based platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC2 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC1 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameters from the kernel command line, as they're
no longer needed for DT-based platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PMIC driver used to register itself as poweroff controller by
default, hence assuming that this device is using the PMIC as
system power controller.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch fixes the following DTC warnings for am57xx-sbc-am57x.dtb:
"endpoint@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap5-igep0050.dtb,
omap5-sbc-t54.dtb and omap5-uevm.dtb:
"connector@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"encoder@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap5-cm-t54.dtb:
"connector@0 has a unit name, but no reg property"
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for am437x-sbc-t43.dtb:
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for am437x-gp-evm.dtb:
"endpoint@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for am43xx-epos-evm.dtb:
"endpoint@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap4-var-dvk-om44.dtb
and omap4-var-stk-om44.dtb:
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap4-sdp.dtb
and omap4-sdp-es23plus.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap4-panda.dtb,
omap4-panda-a4.dtb and omap4-panda-es.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
"encoder@1 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap4-duovero-parlor.dtb:
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-thunder.dtb:
"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-sbc-t3517.dtb,
omap3-sbc-t3530.dtb and omap3-sbc-t3730.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-pandora-600mhz.dtb
and omap3-pandora-1ghz.dtb:
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-overo-summit.dtb,
omap3-overo-storm-tobi.dtb, omap3-overo-storm-summit.dtb and
omap3-overo-tobi.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-igep0020.dtb
and omap3-igep0020-rev-f.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-overo-gallop43.dtb,
omap3-overo-chestnut43.dtb, omap3-overo-storm-chestnut43.dtb,
omap3-overo-palo43.dtb, and omap3-overo-storm-palo43.dtb:
"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-ha-lcd.dtb:
"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-gta04a3.dtb,
omap3-gta04a4.dtb and omap3-gta04a5.dtb:
"dmtimer-pwm@11 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-devkit8000-lcd43.dtb
and omap3-devkit8000-lcd70.dtb:
"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-devkit8000.dtb,
omap3-devkit8000-lcd43.dtb and omap3-devkit8000-lcd70.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-cm-t3517.dtb,
omap3-cm-t3530.dtb and omap3-cm-t3730.dtb:
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-beagle-xm.dtb:
"encoder@0 has a unit name, but no reg property"
"encoder@0/ports/port@0/endpoint@0 has a unit name, but no reg property"
"encoder@0/ports/port@1/endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-beagle.dtb:
"encoder@0 has a unit name, but no reg property"
"encoder@0/ports/port@0/endpoint@0 has a unit name, but no reg property"
"encoder@0/ports/port@1/endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-n900.dtb:
"dmtimer-pwm@9 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"dmtimer-pwm@10 has a unit name, but no reg property"
"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for am3517-craneboard.dtb:
"fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap2430-sdp.dtb:
"func_96m_ck has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix pll3x2 and pll7x2 not having a parent clock, specifically this
fixes the kernel turning of pll3 while simplefb is using it when
uboot has configured things to use pll3x2 as lcd ch clk parent.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the Broadcom BCM953012 Enterprise Router reference
board, enable the following peripherals:
- UART0 (UART1 is not populated)
- WPS and restart GPIO buttons
- Ethernet switch w/ only two facing ports
- NAND flash
- SPI-NOR flash
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add "ti,cpsw-mdio" for am335x/am437x/dra7 SoCs where MDIO is
implemented as part of TI CPSW and, this way, enable PM runtime auto
suspend for Davinci MDIO driver on these paltforms.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Computer on Module Colibri iMX7S/iMX7D along
with the development/evaluation carrier board device trees. Follow
the usual hierarchic include model, maintaining shared configuration
in imx7-colibri.dtsi and imx7-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The base device tree uses KEY_POWER in the snvs-powerkey node,
hence include the input.h header file in the base device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7Solo implements a subset of features available on
i.MX 7Dual. Recreate imx7s.dtsi as the base device tree for
i.MX 7Dual boards. The i.MX 7Dual's additional features over
i.MX 7Solo are:
- Second Cortex-A7 core
- Second Gigabit Ethernet controller
- EPD (Electronc Paper Display, not yet part of the device tree)
- PCIe (not yet part of the device tree)
- Additional USB2.0 OTG controller
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7 series currently consists of two SoCs: i.MX 7Solo and
7Dual. The former has a subset of features of the latter, hence
use imx7s.dtsi as the new base device tree. To keep diffstat nice,
just move imx7d.dtsi to imx7s.dtsi temporarily and recreate
imx7d.dtsi in a second commit.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
bx50v3 boards can be powered off via GPIO, this patch specifies the GPIO to
be used with the gpio-poweroff driver.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for cortex-a7-pmu present on ipq4019 SoCs.
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This is the first Dragonboard based on APQ8060 and PM8058. It
was produced in 2011 in cooperation between Qualcomm and
BSQUARE.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
There is currently a fixed regulator in the .dtsi file for
the MSM8660 chipset, used by the SURF board. We want to define
real regulators for a board using this chipset, so push the fixed
regulator down to the SURF board which is the only user.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The RTC was defined on 0x11d but on the MSM8660/APQ8060 it is
actually on 0x1e8. We were saved by the fact that the driver does
not use the reg parameter: instead it uses the compatible string
to figure out where the RTC is.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The I2C block on the GSBI12 is used on the APQ8060 Dragonboard for
sensors. Make it available in the chipset file.
Take this opportunity to fix the IRQ flag "0" to "NONE" using the
IRQ DT include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the L2CC IPC resource and RPM devices plus the nodes
for the PM8901 and PM8058 regulators to the MSM8660 device tree.
This was tested on the APQ8060 Dragonboard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The SDCC5 SD/MMC controller is used for a second uSD slot
on the APQ8060 Dragonboard. On most other systems it is just
dark silicon so define it and leave it as "disabled" in the core
SoC file.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the 8660 PMIC GPIO and MPP blocks to the MSM8660
DTSI. Verified against the vendor tree to be in these locations
with these interrupts, tested on the APQ8060 Dragonboard.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Since the pmic8xxx-pwrkey driver is already supported in the
qcom-apq8064.dtsi, and the pmic8xxx-pwrkey supports logic to
configure proper device shutdown when ps_hold goes low, it is
better to use that driver then a generic gpio button.
Thus this patch remove the gpio power key entry here, so we
don't get double input events from having two drivers enabled.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andy Gross <agross@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch updates the qcom,state-cells to qcom,smem-state-cells to
match recent changes to the binding.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the qcom,controlled-remotely property for the blsp2_bam
controller node. This board requires this, otherwise the board fails to
boot due to access of protected registers during BAM initialization.
Fixes: 62bc817922 dts: msm8974: Add blsp2_bam dma node
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This board locks up if we stress test the eMMC, as the regulator s4 is
unable to supply enough current for all the peripherials attached to it.
As this supply is wired up to most of the peripherials including DDR,
it resulted in such lockup.
This patch fixes this issue by setting s4 regulator correctly with
Auto power mode.
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[Srinivas Kandagatla: rewrote the change log]
Tested-by: Girish Sharma <girish.sharma@einfochips.com>
Signed-off-by: Parth Pancholi <parth.pancholi@einfochips.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This board has been renamed recently and announced at
https://eragon.einfochips.com/products/sd-600eval.html
So rename this board files so that it reflects actual product in market.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch move sdcc3 pinctrl nodes out of board file, so that
other boards do not duplicate the same thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch moves out the sdcc1 pinctrl nodes out of board files to soc file,
so that it will be duplicated in other board files.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Initial release for rk3229 evb board, and turn the GMAC on.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We have the brother chipset that RK3228 and RK3229, they share most
of dts configuration, but there are a number of different features.
In order to develop the future when they are easy to distinguish,
we need them to be independent.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the DT node for the random number generator peripheral.
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- dts: rename 'ide-disk' to 'disk-activity'
- platform: rename 'ide-disk' to 'disk-activity'
- defconfig: rename 'LEDS_TRIGGER_IDE_DISK' to 'LEDS_TRIGGER_DISK'
Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Various I/O memory fix for Cortex A9 based SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAldo+JYACgkQCwYYjhRyO9XI5QCglOxAOJSamD5IgIpMklk/5ZpG
/MEAn0j80ClwN+YB+/eii/iUMwHwMDQe
=iyoH
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.7-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.7 (part 1)
Various I/O memory fix for Cortex A9 based SoCs
* tag 'mvebu-fixes-4.7-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-38x: fix MBUS_ID for crypto SRAM on Armada 385 Linksys
ARM: mvebu: map PCI I/O regions strongly ordered
ARM: mvebu: fix HW I/O coherency related deadlocks
Signed-off-by: Olof Johansson <olof@lixom.net>
Describe JPEG Processing Unit (JPU) in the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add JPU clock and its parent, M2 clock to the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) DU pin data to the SILK board's device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
