Commit Graph

546504 Commits

Author SHA1 Message Date
Siarhei Siamashka
96521b7200 ARM: dts: sun4i: Allow to use the PH6 pin for GPIO on pcDuino1/2
The pcDuino1 board does not use any power switches at all for its
two USB host ports and the VBUS pins are always connected to 5V.

The pcDuino2 board uses the RT9701GB power switch for its single
USB host port, but the USB_EN pin (PD2) is pulled up with a 10K
resistor. So that the USB power is still enabled by default,
resulting in the same behaviour as pcDuino1 if nobody touches
the PD2 pin. This minor difference is going to be handled in a
follow-up patch, introducing a separate dts file for pcDuino2.

The primary reason for this fix is that the current dts file
unnecessarily meddles with the PH3 and PH6 pins. But the PH6 pin
is available on the Arduino-compatible expansion header and may
have a better use for other purposes. This patch fixes the
problem and now the PH6 pin can be used with the GPIO sysfs
interface. Tested on a pcDuino2 board with a multimeter:

    echo 230 > /sys/class/gpio/export
    echo "out" > /sys/class/gpio/gpio230/direction
    echo 0 > /sys/class/gpio/gpio230/value
    echo 1 > /sys/class/gpio/gpio230/value

USB still works as expected too.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-11 18:47:42 +02:00
Hans de Goede
dcfd8443d8 ARM: dts: sun7i: Enable USB DRC on Bananapi
Enable the otg/drc usb controller on the Bananapi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-11 18:45:36 +02:00
Timo Sigurdsson
a15b80fb0a ARM: dts: sunxi: Add regulators for LeMaker BananaPi
sun7i-a20-bananapi.dts doesn't contain regulator nodes for the AXP209 PMU
driver, so add them to allow for voltage-scaling with cpufreq-dt. Also
add board-specific OPP to use slightly higher voltages at lower
frequencies since Kevin Hilman reported that not all BananaPi boards run
stable at the default voltages inherited by sun7i-a20.dtsi.

Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-11 18:42:15 +02:00
Chen-Yu Tsai
52095d179c ARM: dts: sun6i: hummingbird: Drop AXP221 DC1SW and DC5LDO supplies
"dcdc1-supply" and "dcdc5-supply" have been dropped, as they are
internally connected and should not be represented in the device
tree.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-07 11:34:54 +01:00
Chen-Yu Tsai
b2ec7029c9 ARM: dts: sun8i: sinlinx-sina33: Enable Reduced Serial Bus controller
The Reduced Serial Bus controller is used to talk to the onboard PMIC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-07 10:56:32 +01:00
Chen-Yu Tsai
d4eac998b9 ARM: dts: sun8i: q8-common: Enable RSB controller for A23/A33 Q8 tablets
The Reduced Serial Bus controller is used to talk to the onboard PMIC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-07 10:56:16 +01:00
Chen-Yu Tsai
79d05ec96a ARM: dts: sun8i: Add Reduced Serial Bus controller device node to A23/A33 dtsi
This patch adds a device node for the Reduced Serial Bus (RSB)
controller and the defacto pinmux setting to the A23/A33 dtsi.

Since there is only one possible pinmux setting for RSB, just
set it in the dtsi.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-07 10:55:54 +01:00
Siarhei Siamashka
a2f1a68011 ARM: dts: sun4i: Add AXP209 PMU regulators for pcDuino1/2
This allows voltage-scaling with cpufreq-dt. The reliability of
voltage-scaling has been checked by reducing the voltage of all
operating points by 0.025V (for extra safety headroom) and running
libjpeg-turbo decoding tests on 5 pcDuino2 boards. It means that
the standard sun4i voltages should be perfectly fine too.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-05 14:56:11 +02:00
Marcus Cooper
15ada16dc7 ARM: sun7i: dt: Add new Olimex A20 EVB device
The A20-SOM-EVB is a reference design of a 2-layer board for the
A20-SOM.
It expands the features of A20-SOM by adding VGA connector, HDMI
connector, audio In/Out, LCD connector, 2 Mpix camera, gigabit
Ethernet, SATA, USB-OTG and 2 USB hosts.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-01 15:10:06 +02:00
Chen-Yu Tsai
7f14bededb ARM: dts: sun6i: hummingbird: Add aliases for rtc devices
The hummingbird A31 has 2 rtc devices available: one in the SoC,
and a pcf8563 external rtc on i2c2.

For some unknown reason, the onboard backup battery alone can not
supply enough power to the internal rtc. When external power is
removed, the internal rtc would reset. Hence we want to use the
external one by default.

Add aliases for the rtc devices with the external one as rtc0.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-01 14:56:06 +02:00
Jelle de Jong
b5cf002245 ARM: dts: sun7i: Add dts file for Wits Pro A20 DKT
The Wits Pro A20 DKT is an A20 Development KiT with 1G RAM, 4G NAND,
sdio wifi, 1Gbit ethernet, 1024x768 lcd screen with ft5x_ts touchscreen
and a ton of IO connectors.

Note there seem to be multiple sdcard slots on the board (4 in total), but
other then mmc0 none of these are hooked up by default, there is a ton of
dip-switches which likely allow hooking some of these up, but the
documentation of the board only describes the use of a fraction of them,
so for now we only support mmc0.

Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
[hdegoede@redhat.com: Use pwrseq instead of a regulator for the wifi-en pin]
[hdegoede@redhat.com: Add support for OOB irq for the sdio wifi]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-29 10:03:38 +02:00
Aleksei Mamlin
47038677e5 ARM: dts: sun7i: Enable USB DRC on Wexler TAB7200
Enable the otg/drc usb controller on the Wexler TAB7200 tablet.

Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-29 09:55:09 +02:00
Reinder de Haan
9324ef4b14 ARM: dts: sun7i: Enable USB DRC on the Orange pi
Add usb otg support for Orange pi, based on Orange pi mini.

Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-29 09:55:00 +02:00
Hans de Goede
3ff427f02d ARM: dts: sun7i: Enable USB DRC on orangepi-mini
Enable the otg/drc usb controller on the orangepi-mini.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-29 09:54:55 +02:00
Hans de Goede
5b3abbee42 ARM: dts: axp209: Add usb_power_supply child node to the ax209 node
Add a node representing the usb power supply part of the axp209 pmic, note
that the usb power supply and the (to be added later) ac power supply will
each have their own child-node, so that they can be separately specified
as power-supply for other nodes using a power-supply property with a
phandle pointing to the right axp209 child-node.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-29 09:52:50 +02:00
Hans de Goede
9f06c5309a ARM: dts: sun8i: Make ippo-q8h-v1.2.dts a symlink to q8-tablet.dts
A33 Q8 tablets with the ippo-q8h-v1.2 pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.

We cannot just drop the ippo-q8h-v1.2.dtb as existing u-boot configs
may very well point to it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-28 10:33:56 +02:00
Hans de Goede
beff1084f1 ARM: dts: sun8i: Add sun8i-a33-q8-tablet.dts file
This is a generic dts file for A33 based q8 formfactor tablets,
this is intended to replace both sun8i-a33-ippo-q8h-v1.2.dts and
sun8i-a33-et-q8-v1.6.dts (these can be fully dropped after a
transition period).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-28 10:33:44 +02:00
Lawrence Yu
849147cdb5 ARM: dts: sun6i: Add support for Yones Toptech bs1078v2 tablets
The bs1078v2 is a pcb found in 10.1" tablets with an A31 soc, 1G RAM
and 8G NAND, rtl8723as usb wifi, 1 micro USB OTG port, 1 USB HOST port

This commit adds a dts for v2 of the bs1078 pcb.

Signed-off-by: Lawrence Yu <lyu@micile.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:33 +02:00
Aleksei Mamlin
40088eb407 ARM: dts: sun4i: Enable USB DRC on the Marsboard A10
Enable the otg/drc usb controller on the Marsboard A10.
Similar to Cubieboard, the 5V of the otg is directly connected to the
general 5V, so we only use the id pin.

Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:33 +02:00
Priit Laes
0372bb6b92 ARM: dts: sun4i: gemei-g9: Add accelerometer (bma250) IRQ
Add IRQ configuration for bma250 accelerometer.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:32 +02:00
Chen-Yu Tsai
f7ad082cac ARM: dts: sun8i-a33: Add security system crypto engine clock and device nodes
A33 has the same "Security System" crypto engine as A10/A20, but with a
separate reset control.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:32 +02:00
Chen-Yu Tsai
f5f1c2cbe8 ARM: dts: sun8i: Add pwm-backlight device for A23/A33 Q8 format tablets
The LCD backlight on the A23/A33 Q8 format tablets is enabled
with a GPIO controlled regulator, and brightness controlled with
the SoC's PWM controller.

The backlight is powered from the AXP223 PMIC's DC1SW output,
which is not supported yet. A proper bootloader is required
to enable it.

The brightness levels are arbitrary. The FEX files do not have
such information. As such, actual brightness levels may differ
from device to device.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:32 +02:00
Maxime Ripard
36034fc195 ARM: sun8i: A23: Add missing msgbox gate
Even though it's not mentionned in the A23 user manual, the A23 has a gate
for the AHB1 clock to the msgbox IP. Add it to the clock-indices.

Reported-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:31 +02:00
Maxime Ripard
f42a9505d1 ARM: sun8i: Move A23 AHB1 gates out of common DTSI
The AHB1 gates were assumed to be identical between the A23 and the A33,
which turned out to be wrong. Move the A23 gates definition to the A23
DTSI.

Reported-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:31 +02:00
Maxime Ripard
fe8872c176 ARM: sun8i: Add the A33 AHB1 gates clock driver
The A33 has a different gates array than the A23, add the node to the DT.

Reported-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:30 +02:00
Hans de Goede
eb2217b4c2 ARM: dts: sun5i: Add dts file for q8 formfactor a13 based tablets
This commits adds a generic dts file for q8 formfactor a13 based tablets.

The tablets ship in many variants, with the difference mainly being the
touchscreen controller / accelerometer / wifi chip used.

The wifi is USB based, and thus not listed in devicetree.

The touchscreen controller / accelerometer may turn out to be a problem
once we add support for those. We can either do something with devicetree
overlays, or add sun5i-a13-<touchscreen>-<accelerometer>.dts files. The
latter is what the android mod community is doing with firmware images.

This dts was tested with an a13 q8 tablet with a pcb labelled: "94V-0",
silead gsl1680 touchscreen controller and a mc32x0 accelerometer.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:30 +02:00
Hans de Goede
d5c1274f26 ARM: dts: sun5i: Add sun5i-q8-common.dtsi
This is the sun5i / a13 version of sun8i-q8-common.dtsi for use in dts
files for a13 q8 based tablets. Compared to sun8i this uses uart1 for the
serial console, and PG0 for card-detect for mmc0.

This also adds pmic and otg support, which both use the same config on
all known q8 a13 devices. This is not present in sun5i-q8-common.dtsi
because pmic / otg support for sun8i has not yet been merged.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:29 +02:00
Chen-Yu Tsai
29a0d085b7 ARM: dts: sun8i: Add PWM channel 0 pinmux setting for A23/A33
The PWM controller has 2 outputs, with one usable pin for each.

Add a pinmux setting for the first channel. This is often used
for backlight dimming on tablets.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:28 +02:00
Chen-Yu Tsai
832f977c8b ARM: dts: sun8i: Add PWM controller node for A23/A33
A23/A33 have a PWM controller that is compatible to the one on the A20.
Add a device node for it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:28 +02:00
Yassin Jaffer
6f1606bfe9 ARM: dts: sun7i: Add keypad clk node
This patch add support to the keypad clock on sun7i

Signed-off-by: Yassin Jaffer <yassinjaffer@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:27 +02:00
Sander Vermin
5d97c677a9 ARM: dts: sun6i: Add accelerometer on Columbus A31
Add mma8452 accelerometer to sun6i-a31-colombus.dts.

Signed-off-by: Sander Vermin <sander@vermin.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:27 +02:00
Jelle van der Waa
adfa06ce9b ARM: dts: sun5i: Add dts file for the Wobo i5 top set box
The Wobo i5 top set box is a somewhat curious A10s based top set box,
it uses an AXP209 rather then the AXP152 usually used in combination
with the A10s. It has an ethernet phy connected to PORTD rather then
PORTA, and its built-in usb wifi is connected via the otg controller.

This commit adds a dts file adding support for this top set box.

Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:26 +02:00
Jelle van der Waa
bea9b7bcf3 ARM: dts: sun5i: Add emac_pins_b definition
The emac pins on an A10s can also be routed to the outside through
PORTD rather then through PORTA, add a pinctrl node for this.

Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:26 +02:00
Olliver Schinagl
f49243f130 dts: sunxi: add eeprom to A20 OLinuXino micro board
The Olimex A20 OLinuXino Micro features an eeprom that is always on the
board. This patch adds it to the dts.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:25 +02:00
Olliver Schinagl
dbca81d2f9 dts: sunxi: add eeprom to A20 OLinuXino Lime2 board
The Olimex A20 OLinuXino Lime2 features an eeprom that is always on the
board. This patch adds it to the dts.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:25 +02:00
Olliver Schinagl
d2057c59be dts: sunxi: add eeprom to A20 OLinuXino Lime board
The Olimex A20 OLinuXino Lime features an eeprom that is always on the
board. This patch adds it to the dts.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:24 +02:00
Olliver Schinagl
ce350094ca dts: sunxi: correct vendor prefix on OLinuXino a10s micro
The OLinuXino A10S micro features an eeprom. According to the eeprom.txt
binding document, we should use the manufacturer and 'at' is not the
proper manufacturer id according to the vendor-prefixes.

This patch takes the proper vendor-prefix and uses it for the eeprom
node.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:24 +02:00
Olliver Schinagl
e89ecbf141 dts: sunxi: add eeprom to A10 OLinuXino Lime board
The Olimex A10 OLinuXino Lime features an eeprom that is always on the
board. This patch adds it to the dts.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:23 +02:00
Hans de Goede
b92b14909e ARM: dts: sun4i: Add dts file for iNet-1 based tablets
The iNet-tek iNet-1 PCB is a PCB found in various generic 10.1" 1024x600
A10 based tablets such as the Point of View Protab2 XXL and the
Cherry M1007.

This patch has been tested on both rev2 and rev5 of this board / these
tablets.

It comes with a rtl8188cus usb wifi connected to ehci1, focal ft5406ee8
touchscreen connected to i2c2 addr 0x38, bosch bma 250 accelerometer
connected to i2c1 addr 0x18 and the usual connectors: headphone,
mini hdmi, power-barrel, mini-usb and a micro-sd slot.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:23 +02:00
Hans de Goede
2ecf488b14 ARM: dts: sun4i: Add dts file inet9f-rev03 based tablets
The inet9f-rev03 pcb is specially designed for gaming tablets, such as
the qware tb-g100 tablet.

These 7" tablets feature a dpad, firebuttons and 2 joysticks on the sides
of the screen.

Besides this they have the usual connectors: power-barrel, mini usb,
mini hdmi, headphone and micro-sd slot.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:22 +02:00
Hans de Goede
72df94cbec ARM: dts: sunxi: Add sun?i-q8-common.dtsi files for q8 tablets
Cheap allwinner based devices in the q8 enclosure come in many variants,
all sharing the case and a number of other basic features.

They differ in the display, touchscreen, accelerometer and wifi chips
used.

This commit adds 2 dtsi files defining the shared features of all the
q8 tablets. sunxi-q8-common.dtsi defines features shared amongst all
q8 tablets, sun8i-q8-common.dtsi defines features shared amongst all
a23 / a33 based q8 tablets, but not with a13 q8 based tablets.

a13 based tablets use a different card-detect pin for the mmc, and
use uart1 instead of the r_uart for the serial console.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:22 +02:00
Hans de Goede
ac1dd1dcc5 ARM: dts: sun5i: Add dts file for inet98v_rev2 based tablets
The inet98v_rev2 is a pcb used in generic A13 based tablets. It features
volume buttons, a power barrel, micro-usb otg, headphone connector and
a power button.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:21 +02:00
Chen-Yu Tsai
4917c46ced ARM: dts: sun6i: Add mmc2 pins for 8 bit emmc
This also includes the reset pin for emmc.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:21 +02:00
Chen-Yu Tsai
61d2595cd1 ARM: dts: sun6i: Add lradc node
sun6i also has the LRADC for tablet buttons.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:21 +02:00
Hans de Goede
ff9dc0b93b ARM: dts: sun4i: inet97fv2: Enable i2c1 and i2c2 controllers
Enable i2c1 and i2c2 controllers, these are used for the touchscreen resp.
the accelerometer.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:20 +02:00
Hans de Goede
2d4f66355b ARM: dts: sun4i: inet97fv2: Enable support for tablet keys
Enable support for the tablet keys which are connected via the lradc.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:20 +02:00
Hans de Goede
64a6295e62 ARM: dts: sun4i: inet97fv2: Enable otg controller
Enable the otg controller on the inet97fv2 tablet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:19 +02:00
Hans de Goede
5fed0cbf4f ARM: dts: sun4i: inet97fv2: Add regulator nodes
Use axp209.dtsi and add regulator nodes for the regulators used on the
inet97fv2 tablet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:19 +02:00
Hans de Goede
cb8b85a89a ARM: dts: sun4i: inet97fv2: Disable unused usb controllers
The inet97fv2 tablet only has a usb-2 wifi device connected to the second
ehci controller, disable the first ehci controller and both ohci
controllers.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:18 +02:00
Hans de Goede
2a9a5cfaf1 ARM: dts: sun5i: Add support for the Auxtek-T003 HDMI stick
The Auxtek-T003 HDMI stick is an A10s based HDMI stick with USB wifi,
and composite video out support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-09-27 10:21:18 +02:00