At the time of firmware initialization, if JBOD map or RAID map is not
available, driver can function without these features in a limited
functionality mode.
Link: https://lore.kernel.org/r/1579000882-20246-6-git-send-email-anand.lodnoor@broadcom.com
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Anand Lodnoor <anand.lodnoor@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ideally, optimal queue depth will be provided by firmware. The driver
defines will be used as a fallback mechanism in case the FW assisted QD is
not supported. The driver defined values provide optimal queue depth for
most of the drives and the workloads, as is learned from the firmware
assisted QD results.
Link: https://lore.kernel.org/r/1579000882-20246-4-git-send-email-anand.lodnoor@broadcom.com
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Anand Lodnoor <anand.lodnoor@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Disable WRITE_SAME (no_write_same) for Virtual Disks only. For System PDs
and EPDs (Enhanced PDs), WRITE_SAME need not be disabled by default.
Link: https://lore.kernel.org/r/1579000882-20246-3-git-send-email-anand.lodnoor@broadcom.com
Signed-off-by: Anand Lodnoor <anand.lodnoor@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After device resume we expect the firmware to be in READY state.
Transition to READY might fail due to unhandled exceptions, such as an
internal error or a hardware failure. Retry initiating chip reset and wait
for the controller to come to ready state.
Link: https://lore.kernel.org/r/1579000882-20246-2-git-send-email-anand.lodnoor@broadcom.com
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Anand Lodnoor <anand.lodnoor@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do firmware download with 64bit LOAD_RAM command, if driver is using
64bit addressing.
Link: https://lore.kernel.org/r/20200114160936.1517-1-tbogendoerfer@suse.de
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the transport cannot be registered, the session/connection creation
needs to be failed early to let the initiator know. Otherwise, the system
will have an outstanding connection that cannot be used nor removed by
open-iscsi. The result is similar to the error below, triggered by
injecting a failure in the transport's registration path.
openiscsi reports success:
root@debian-vm:~# iscsiadm -m node -T iqn:lun1 -p 127.0.0.1 -l
Logging in to [iface: default, target: iqn:lun1, portal: 127.0.0.1,3260]
Login to [iface: default, target: iqn:lun1, portal:127.0.0.1,3260] successful.
But cannot remove the session afterwards, since the kernel is in an
inconsistent state.
root@debian-vm:~# iscsiadm -m node -T iqn:lun1 -p 127.0.0.1 -u
iscsiadm: No matching sessions found
Link: https://lore.kernel.org/r/20200106185817.640331-4-krisman@collabora.com
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The transport registration may fail. Make sure the errors are propagated
to the callers.
Link: https://lore.kernel.org/r/20200106185817.640331-3-krisman@collabora.com
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
attribute_container_device_trigger invokes callbacks that may fail for one
or more classdevs, for instance, the transport_add_class_device callback,
called during transport creation, does memory allocation. This
information, though, is not propagated to upper layers, and any driver
using the attribute_container_device_trigger API will not know whether any,
some, or all callbacks succeeded.
This patch implements a safe version of this dispatcher, to either succeed
all the callbacks or revert to the original state.
Link: https://lore.kernel.org/r/20200106185817.640331-2-krisman@collabora.com
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pass UFS device information to vendor-specific variant callback
"apply_dev_quirks" because some platform vendors need to know such
information to apply special handling or quirks in specific devices.
At the same time, modify existing vendor implementations according to the
new interface for those vendor drivers which will be built-in or built as a
module alone with UFS core driver.
[mkp: clarified commit desc]
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1578726707-6596-2-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the incorrect %X print format specifier is being used for several
unsigned longs. Fix these by using %lX instead. Also join up some literal
strings that are split.
Link: https://lore.kernel.org/r/20200108193800.96706-1-colin.king@canonical.com
Addresses-Coverity: ("Invalid type in argument to printf format specifier")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Khalid Aziz <khalid@gonehiking.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove "errors" word in output string by ufshcd_print_err_hist() since not
all printed targets are "errors". Sometimes they are just "events".
In addition, all events which can be treated as "errors" already have "err"
or "fail" words in their names.
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1578147968-30938-4-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Device reset history shall be also added for vendor's device reset variant
operation implementation.
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1578147968-30938-3-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently checking if an error history element is empty or not is by its
"value". In most cases, value is error code.
However this checking is not correct because some errors or events do not
specify any values in error history so values remain as 0, and this will
lead to incorrect empty checking.
Fix it by checking "timestamp" instead of "value" because timestamp will be
always assigned for all history elements
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1578147968-30938-2-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warning:
drivers/scsi/lpfc/lpfc_nportdisc.c:344:1: warning:
symbol 'lpfc_defer_acc_rsp' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20200107014956.41748-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series concludes the work I did for linux-5.5 on the compat_ioctl()
cleanup, killing off fs/compat_ioctl.c and block/compat_ioctl.c by moving
everything into drivers.
Overall this would be a reduction both in complexity and line count, but
as I'm also adding documentation the overall number of lines increases
in the end.
My plan was originally to keep the SCSI and block parts separate.
This did not work easily because of interdependencies: I cannot
do the final SCSI cleanup in a good way without first addressing the
CDROM ioctls, so this is one series that I hope could be merged through
either the block or the scsi git trees, or possibly both if you can
pull in the same branch.
The series comes in these steps:
1. clean up the sg v3 interface as suggested by Linus. I have
talked about this with Doug Gilbert as well, and he would
rebase his sg v4 patches on top of "compat: scsi: sg: fix v3
compat read/write interface"
2. Actually moving handlers out of block/compat_ioctl.c and
block/scsi_ioctl.c into drivers, mixed in with cleanup
patches
3. Document how to do this right. I keep getting asked about this,
and it helps to point to some documentation file.
The branch is based on another one that fixes a couple of bugs found
during the creation of this series.
Changes since v3:
https://lore.kernel.org/lkml/20200102145552.1853992-1-arnd@arndb.de/
- Move sr_compat_ioctl fixup to correct patch (Ben Hutchings)
- Add Reviewed-by tags
Changes since v2:
https://lore.kernel.org/lkml/20191217221708.3730997-1-arnd@arndb.de/
- Rebase to v5.5-rc4, which contains the earlier bugfixes
- Fix sr_block_compat_ioctl() error handling bug found by
Ben Hutchings
- Fix idecd_locked_compat_ioctl() compat_ptr() bug
- Don't try to handle HDIO_DRIVE_TASKFILE in drivers/ide
- More documentation improvements
Changes since v1:
https://lore.kernel.org/lkml/20191211204306.1207817-1-arnd@arndb.de/
- move out the bugfixes into a branch for itself
- clean up scsi sg driver further as suggested by Christoph Hellwig
- avoid some ifdefs by moving compat_ptr() out of asm/compat.h
- split out the blkdev_compat_ptr_ioctl function; bug spotted by
Ben Hutchings
- Improve formatting of documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cddL
-----END PGP SIGNATURE-----
Merge tag 'block-ioctl-cleanup-5.6' into 5.6/scsi-queue
Pull compat_ioctl cleanup from Arnd. Here's his description:
This series concludes the work I did for linux-5.5 on the compat_ioctl()
cleanup, killing off fs/compat_ioctl.c and block/compat_ioctl.c by moving
everything into drivers.
Overall this would be a reduction both in complexity and line count, but
as I'm also adding documentation the overall number of lines increases
in the end.
My plan was originally to keep the SCSI and block parts separate.
This did not work easily because of interdependencies: I cannot
do the final SCSI cleanup in a good way without first addressing the
CDROM ioctls, so this is one series that I hope could be merged through
either the block or the scsi git trees, or possibly both if you can
pull in the same branch.
The series comes in these steps:
1. clean up the sg v3 interface as suggested by Linus. I have
talked about this with Doug Gilbert as well, and he would
rebase his sg v4 patches on top of "compat: scsi: sg: fix v3
compat read/write interface"
2. Actually moving handlers out of block/compat_ioctl.c and
block/scsi_ioctl.c into drivers, mixed in with cleanup
patches
3. Document how to do this right. I keep getting asked about this,
and it helps to point to some documentation file.
The branch is based on another one that fixes a couple of bugs found
during the creation of this series.
Changes since v3:
https://lore.kernel.org/lkml/20200102145552.1853992-1-arnd@arndb.de/
- Move sr_compat_ioctl fixup to correct patch (Ben Hutchings)
- Add Reviewed-by tags
Changes since v2:
https://lore.kernel.org/lkml/20191217221708.3730997-1-arnd@arndb.de/
- Rebase to v5.5-rc4, which contains the earlier bugfixes
- Fix sr_block_compat_ioctl() error handling bug found by
Ben Hutchings
- Fix idecd_locked_compat_ioctl() compat_ptr() bug
- Don't try to handle HDIO_DRIVE_TASKFILE in drivers/ide
- More documentation improvements
Changes since v1:
https://lore.kernel.org/lkml/20191211204306.1207817-1-arnd@arndb.de/
- move out the bugfixes into a branch for itself
- clean up scsi sg driver further as suggested by Christoph Hellwig
- avoid some ifdefs by moving compat_ptr() out of asm/compat.h
- split out the blkdev_compat_ptr_ioctl function; bug spotted by
Ben Hutchings
- Improve formatting of documentation
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Documentation/process/botching-up-ioctls.rst was orignally written as
a blog post for DRM driver writers, so it it misses some points while
going into a lot of detail on others.
Try to provide a replacement that addresses typical issues across a wider
range of subsystems, and follows the style of the core-api documentation
better.
Many improvements to the document are suggested by Ben Hutchings
<ben.hutchings@codethink.co.uk>, Jonathan Corbet <corbet@lwn.net> and
Geert Uytterhoeven <geert@linux-m68k.org>.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Having separate implementations of blkdev_ioctl() often leads to these
getting out of sync, despite the comment at the top.
Since most of the ioctl commands are compatible, and we try very hard
not to add any new incompatible ones, move all the common bits into a
shared function and leave only the ones that are historically different
in separate functions for native/compat mode.
To deal with the compat_ptr() conversion, pass both the integer
argument and the pointer argument into the new blkdev_common_ioctl()
and make sure to always use the correct one of these.
blkdev_ioctl() is now only kept as a separate exported interfact
for drivers/char/raw.c, which lacks a compat_ioctl variant.
We should probably either move raw.c to staging if there are no
more users, or export blkdev_compat_ioctl() as well.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is no need to go through a compat_alloc_user_space()
copy any more, just wrap the function in a small helper that
works the same way for native and compat mode.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Having both in the same file allows a number of simplifications
to the compat path, and makes it more likely that changes to
the native path get applied to the compat version as well.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Most of the HDIO ioctls are only used by the obsolete drivers/ide
subsystem, these can be handled by changing ide_cmd_ioctl() to be aware
of compat mode and doing the correct transformations in place and using
it as both native and compat handlers for all drivers.
The SCSI drivers implementing the same commands are already doing
this in the drivers, so the compat_blkdev_driver_ioctl() function
is no longer needed now.
The BLKSECTSET and HDIO_GETGEO_BIG ioctls are not implemented
in any driver any more and no longer need any conversion.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ata_sas_scsi_ioctl() function implements a number of HDIO_* commands
for SCSI devices, it is used by all libata drivers as well as a few
drivers that support SAS attached SATA drives.
The only command that is not safe for compat ioctls here is
HDIO_GET_32BIT. Change the implementation to check for in_compat_syscall()
in order to do both cases correctly, and change all callers to use it
as both native and compat callback pointers, including the indirect
callers through sas_ioctl and ata_scsi_ioctl.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is no need for the special cases for the cdrom ioctls any more now,
so make sure that each cdrom driver has a .compat_ioctl() callback and
calls cdrom_compat_ioctl() directly there.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that both native and compat ioctl syscalls are
in the same file, a couple of simplifications can
be made, bringing the implementation closer together:
- do_vfs_ioctl(), ioctl_preallocate(), and compat_ioctl_preallocate()
can become static, allowing the compiler to optimize better
- slightly update the coding style for consistency between
the functions.
- rather than listing each command in two switch statements
for the compat case, just call a single function that has
all the common commands.
As a side-effect, FS_IOC_RESVSP/FS_IOC_RESVSP64 are now available
to x86 compat tasks, along with FS_IOC_RESVSP_32/FS_IOC_RESVSP64_32.
This is harmless for i386 emulation, and can be considered a bugfix
for x32 emulation, which never supported these in the past.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The rest of the fs/compat_ioctl.c file is no longer useful now,
so move the actual syscall as planned.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Each driver calling scsi_ioctl() gets an equivalent compat_ioctl()
handler that implements the same commands by calling scsi_compat_ioctl().
The scsi_cmd_ioctl() and scsi_cmd_blk_ioctl() functions are compatible
at this point, so any driver that calls those can do so for both native
and compat mode, with the argument passed through compat_ptr().
With this, we can remove the entries from fs/compat_ioctl.c. The new
code is larger, but should be easier to maintain and keep updated with
newly added commands.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rather than relying on fs/compat_ioctl.c, this adds support
for a compat_ioctl() callback in the ide-floppy driver directly,
which lets it translate the scsi commands.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
bsg_ioctl() calls into scsi_cmd_ioctl() for a couple of generic commands
and relies on fs/compat_ioctl.c to handle it correctly in compat mode.
Adding a private compat_ioctl() handler avoids that round-trip and lets
us get rid of the generic emulation once this is done.
Note that bsg implements an SG_IO command that is different from the
other drivers and does not need emulation.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In order to move the compat handling for SCSI ioctl commands out of
fs/compat_ioctl.c into the individual drivers, we need a helper function
first to match the native ioctl handler called by sd, sr, st, etc.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Various block drivers implement the CDROMMULTISESSION,
CDROM_GET_CAPABILITY, and CDROMEJECT ioctl commands, relying on the
block layer to handle compat_ioctl mode for them.
Move this into the drivers directly as a preparation for simplifying
the block layer later.
When only integer arguments or no arguments are passed, the
same handler can be used for .ioctl and .compat_ioctl, and
when only pointer arguments are passed, the newly added
blkdev_compat_ptr_ioctl can be used.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is the only ioctl command that does not have a proper
compat handler. Making the normal implementation do the
right thing is actually very simply, so just do that by
using an in_compat_syscall() check to avoid the special
case in the pkcdvd driver.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Again, there is only one file that needs this, so move the conversion
handler into the native implementation.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is only one implementation of this ioctl, so move the handling out
of the common block layer code into the place where it's actually needed.
It also gets called indirectly through pktcdvd, which needs to be aware
of this change.
As I noticed, the old implementation of the compat handler failed to
convert the structure on the way out, so the updated fields never got
written back to user space. This is either not important, or it has
never worked and should be fixed now.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These drivers implement the HDIO_GET_IDENTITY and CDROMVOLREAD ioctl
commands, which are compatible between 32-bit and 64-bit user space and
traditionally handled by compat_blkdev_driver_ioctl().
As a prerequisite to removing that function, make both drivers use
blkdev_compat_ptr_ioctl() as their .compat_ioctl callback.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A lot of block drivers need only a trivial .compat_ioctl callback.
Add a helper function that can be set as the callback pointer
to only convert the argument using the compat_ptr() conversion
and otherwise assume all input and output data is compatible,
or handled using in_compat_syscall() checks.
This mirrors the compat_ptr_ioctl() helper function used in
character devices.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In the v5.4 merge window, a cleanup patch from Al Viro conflicted
with my rework of the compat handling for sg.c read(). Linus Torvalds
did a correct merge but pointed out that the resulting code is still
unsatisfactory.
I later noticed that the sg_new_read() function still gets the compat
mode wrong, when the 'count' argument is large enough to pass a
compat_sg_io_hdr object, but not a nativ sg_io_hdr.
To address both of these, move the definition of compat_sg_io_hdr
into a scsi/sg.h to make it visible to sg.c and rewrite the logic
for reading req_pack_id as well as the size check to a simpler
version that gets the expected results.
Fixes: c35a5cfb41 ("scsi: sg: sg_read(): simplify reading ->pack_id of userland sg_io_hdr_t")
Fixes: 98aaaec4a1 ("compat_ioctl: reimplement SG_IO handling")
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In order to avoid needless #ifdef CONFIG_COMPAT checks,
move the compat_ptr() definition to linux/compat.h
where it can be seen by any file regardless of the
architecture.
Only s390 needs a special definition, this can use the
self-#define trick we have elsewhere.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In order to use compat_* type defininitions in device drivers
outside of CONFIG_COMPAT, move the inclusion of asm-generic/compat.h
ahead of the #ifdef.
All other architectures already do this.
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove usage of device_busy counter from driver. Instead of device_busy
counter now driver uses 'nr_active' counter of request_queue to get the
number of inflight request for a LUN.
Link: https://lore.kernel.org/r/20191226111333.26131-10-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print the function name in which MPT command got timed out. This will
facilitate debugging in which path corresponding MPT command got timeout in
first failure instance of log itself.
Link: https://lore.kernel.org/r/20191226111333.26131-9-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This improves mpt3sas driver default debug information collection and
allows for a higher percentage of issues being able to be resolved with a
first-time data capture. However, this improvement to balance the amount
of debug data captured with the performance of driver.
Enabled below print messages with out affecting the IO performance,
1. When task abort TM is received then print IO commands's timeout value
and how much time this command has been outstanding.
2. Whenever hard reset occurs then print from where this hard reset has
been issued.
3. Failure message should be displayed for failure scenarios without any
logging level.
4. Added a print after driver successfully register or unregistered a
target drive with the SML. This print will be useful for debugging the
issue where the drive addition or deletion is hanging at SML.
5. During driver load time print request, reply, sense and config page
pool's information such as its address, length and size. Also printed
sg_tablesize information.
Link: https://lore.kernel.org/r/20191226111333.26131-8-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When Firmware fault occurs then print in which path firmware fault has
occurred. This will be useful while debugging the firmware fault issues.
Link: https://lore.kernel.org/r/20191226111333.26131-7-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Watchdog thread polls for IOC state every 1 second. If it detects that IOC
state is in CoreDump state then it immediately stops the IOs and also
clears the outstanding commands issued to the HBA firmware and then it will
poll for IOC state to be out of CoreDump state and once it detects that IOC
state is changed from CoreDump state to Fault state (or) CoreDumpTOSec
number of seconds are elapsed then it will issue host reset operation and
moves the IOC state to Operational state and resumes the IOs.
Whenever any TM is received from SML then if driver detects the IOC state
is in CoreDump state then it will wait for CoreDump state to be cleared and
will host reset operation.
Link: https://lore.kernel.org/r/20191226111333.26131-6-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New feature is added in HBA firmware where it copies the collected firmware
logs in flash region named 'CoreDump' whenever HBA firmware faults occur.
For copying the logs to CoreDump flash region firmware needs some time and
hence it has introduced a new IOC state named "CoreDump" State.
Whenever driver detects the CoreDump state then it means that some firmware
fault has occurred and firmware is copying the logs to the coredump flash
region. During this time driver should not perform any operation with the
HBA, driver should wait for HBA firmware to move the IOC state from
'CoreDump' state to 'Fault' state once it's done with copying the logs to
coredump region. Once driver detects the Fault state then it will issue the
diag reset/host reset operation to move the IOC state from Fault to
Operational state.
Here the valid IOC state transactions w.r.t to this CoreDump state feature,
Operational -> Fault:
The IOC transitions to the Fault state when an operational error occurs AND
CoreDump is not supported (or disabled) by the firmware(FW).
Operational -> CoreDump:
The IOC transitions to the CoreDump state when an operational error occurs
AND CoreDump is supported & enabled by the FW.
CoreDump -> Fault:
A transition from CoreDump state to Fault state happens when the FW
completes the CoreDump collection.
CoreDump -> Reset:
A transition out of the CoreDump state happens when the host sets the Reset
Adapter bit in the System Diagnostic Register (Hard Reset). This reset
action indicates that CoreDump took longer than the host time out.
Firmware informs the driver about the maximum time that driver has to wait
for firmware to transition the IOC state from 'CoreDump' to 'FAULT' state
through 'CoreDumpTOSec' field of ManufacturingPage11 page. if this
'CoreDumpTOSec' field value is zero then driver will wait for max 15
seconds.
Driver informs the HBA firmware that it supports this new IOC state named
'CoreDump' state by enabling COREDUMP_ENABLE flag in ConfigurationFlags
field of ioc init request message.
Current patch handles the CoreDump state only during HBA initialization and
release scenarios where watchdog thread (which polls the IOC state in every
one second) is disabled. Next subsequent patch handle the CoreDump state
when watchdog thread is enabled.
During HBA initialization or release execution time if driver detects the
CoreDump state then driver will wait for maximum CoreDumpTOSec value
seconds for FW to copy the logs. After that it will issue the diag reset
operation to move the IOC state to Operational state.
Link: https://lore.kernel.org/r/20191226111333.26131-5-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Renamed _base_after_reset_handler function to
_base_clear_outstanding_commands so that it can be used in multiple
scenarios with suitable name which matches with the operation it does.
Also renamed its child functions. No functional changes.
Link: https://lore.kernel.org/r/20191226111333.26131-4-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce function _scsih_nvme_shutdown() to issue IO Unit Control message
to IOC firmware with operation code 'shutdown'. This causes IOC firmware to
issue NVMe shutdown commands to all NVMe drives attached to it.
NVMe Shutdown:
NVMe devices need to have a specific shutdown sequence performed before
power is removed. For this, the IOC firmware needs to be notified when the
system is being shutdown. So during the system shutdown time, driver issues
an IO Unit Control request with operation code MPI26_CTRL_OP_SHUTDOWN to
inform firmware that a shutdown is initiated.
This shutdown command is issued only if NVMe devices are attached to the
controller.
During each NVMe device addition, driver reads pcie device page2 to get
shutdown latency (e.g. drive's RTD3 Entry Latency) and updates the max
latency value among the added NVMe drives in ioc->max_shutdown_latency.
This is used as the timeout value for IO Unit Control command at the time
of shutdown.
When a NVMe drive is removed and its shutdown latency matches which
ioc->max_shutdown_latency then ioc->max_shutdown_latency is updated to next
max value (by iterating over the list of available devices). If the
shutdown latency is 0, then default timeout is set to six seconds.
Link: https://lore.kernel.org/r/20191226111333.26131-3-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
