The current code doeesn't support 20Gbps speed for current and supported
speed. Add support for it.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver was wrongly interpreting the supported cap value returned by qed.
Solution: Use QED define macros instead of OS defined for interpreting
supporting speeds.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver was attempting to print cdb[0], which is not set for resets coming
from SCSI ioctls. Check for cmd_len before accessing cmnd.
Crash info:
[84790.864747] BUG: unable to handle kernel NULL pointer dereference at (null)
[84790.864783] IP: qedf_initiate_tmf+0x7a/0x6e0 [qedf]
[84790.865204] Call Trace:
[84790.865246] scsi_try_target_reset+0x2b/0x90 [scsi_mod]
[84790.865266] scsi_ioctl_reset+0x20f/0x2a0 [scsi_mod]
[84790.865284] scsi_ioctl+0x131/0x3a0 [scsi_mod]
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- On some setups fipvlan can be retried for long duration and the
connection to switch was not there so it was not getting any reply.
- During unload this thread was hanging.
Problem Resolution:
Check if unload is in progress, then quit from fipvlan thread.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print messages during exiting condition to help debugging.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add:
PM8222 VID_9005, DID_028F, SVID_1BD4 and SDID_004F
3101E-4i (1G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0808
3102E-8i (2G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0809
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return -EINPROGRESS when a rescan worker is queued.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When each ld is deleted, a rescan event is triggered in the driver. These
can stack up waiting on mutex_lock.
Change to mutex_try_lock and schedule a rescan for later.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return identify physical device "Phys_Bay_in_Box" as bay_identifier.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- serial number
- model
- vendor
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Expose physical devices before logical devices.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 12.4.0.0 patch that merged WQ/CQ pairs into single per-cpu pair
contained a bug: a local variable was set to the queue pair by index. This
should have allowed the local variable to be natively used. Instead, the
code reused the index relative to the local variable, obtaining a random
pointer value that when used eventually faulted the system
Convert offending code to use local variable.
Fixes: c00f62e6c5 ("scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Capturing and downloading dif command data and dif data was done a dozen
years ago and no longer being used. Also creates a potential security hole.
Remove the debugfs buffer for dif debugging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: KyleMahlkuch <kmahlkuc@linux.vnet.ibm.com>
CC: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Per Dan Carpenter:
The patch d79c9e9d4b: "scsi: lpfc: Support dynamic unbounded SGL lists on
G7 hardware." from Aug 14, 2019, leads to the following static checker
warning:
drivers/scsi/lpfc/lpfc_init.c:4107 lpfc_new_io_buf()
error: not allocating enough data 784 vs 768
There was no need to compare sizes nor to allocate size based on a define.
Change allocation to use actual structure length
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/ufs/ufs-qcom.c: In function ufs_qcom_pwr_change_notify:
drivers/scsi/ufs/ufs-qcom.c:808:6: warning: variable val set but not used [-Wunused-but-set-variable]
Fixes: 1e1e465c6d ("scsi/ufs: qcom: Remove ufs_qcom_phy_*() calls from host")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a spelling mistake in a ql_log message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c: In function cq_interrupt_v1_hw:
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c:1542:6: warning: variable irq_value set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides a module parameter and sysfs interface to select
whether the queue depth for each device should be based on the
protocol-specific value set by the driver (the default) or the maximum
supported by the controller (can_queue).
Although we have a sysfs interface per sdev to change the queue depth
of individual scsi devices, this implementation provides a single
sysfs entry per shost to switch between the controller max and the
driver default.
[mkp: tweaked commit desc]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the firmware documentation a status type 0 IOCB can be
followed by one or more status continuation type 0 IOCBs. Hence do not
complain if the completion function is not called from inside the status
type 0 IOCB handler.
WARNING: CPU: 10 PID: 425 at drivers/scsi/qla2xxx/qla_isr.c:2784
qla2x00_status_entry.isra.7+0x484/0x17b0 [qla2xxx]
CPU: 10 PID: 425 Comm: kworker/10:1 Tainted: G E 5.3.0-rc4-next-20190813-autotest-autotest #1
Workqueue: qla2xxx_wq qla25xx_free_rsp_que [qla2xxx]
Call Trace:
qla2x00_status_entry.isra.7+0x1484/0x17b0 [qla2xxx] (unreliable)
qla24xx_process_response_queue+0x7d8/0xbd0 [qla2xxx]
qla25xx_free_rsp_que+0x1a0/0x220 [qla2xxx]
process_one_work+0x25c/0x520
worker_thread+0x8c/0x5e0
kthread+0x154/0x1a0
ret_from_kernel_thread+0x5c/0x7c
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently bits in hba->outstanding_tasks are cleared only after their
corresponding task management commands are successfully done by
__ufshcd_issue_tm_cmd().
If timeout happens in a task management command, its corresponding bit in
hba->outstanding_tasks will not be cleared until next task management
command with the same tag used successfully finishes.
This is wrong and can lead to some issues, like power issue. For example,
ufshcd_release() and ufshcd_gate_work() will do nothing if
hba->outstanding_tasks is not zero even if both UFS host and devices are
actually idle.
Solution is referred from error handling of device commands: bits in
hba->outstanding_tasks shall be cleared regardless of their execution
results.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pointer fh is being assigned a return value from the call to
skb_transport_header however this value is never read and fh is being
re-assigned immediately afterwards with a new value. Since there are
side-effects from calling skb_transport_header the call is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS devices have issues if LCC is enabled. So we are setting
PA_LOCAL_TX_LCC_Enable to 0 before link startup which will make sure that
both host and device TX LCC are disabled once link startup is completed.
Signed-off-by: Anil Varughese <aniljoy@cadence.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable error is being initialized with a value that is never read and
error is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.4.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, each hardware queue, typically allocated per-cpu, consists of a
WQ/CQ pair per protocol. Meaning if both SCSI and NVMe are supported 2
WQ/CQ pairs will exist for the hardware queue. Separate queues are
unnecessary. The current implementation wastes memory backing the 2nd set
of queues, and the use of double the SLI-4 WQ/CQ's means less hardware
queues can be supported which means there may not always be enough to have
a pair per cpu. If there is only 1 pair per cpu, more cpu's may get their
own WQ/CQ.
Rework the implementation to use a single WQ/CQ pair by both protocols.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FC-NVMe-2 added support for sequence level error recovery in the FC-NVME
protocol. This allows for the detection of errors and lost frames and
immediate retransmission of data to avoid exchange termination, which
escalates into NVMeoFC connection and association failures. A significant
RAS improvement.
The driver is modified to indicate support for SLER in the NVMe PRLI is
issues and to check for support in the PRLI response. When both sides
support it, the driver will set a bit in the WQE to enable the recovery
behavior on the exchange. The adapter will take care of all detection and
retransmission.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Typical SLI-4 hardware supports up to 2 4KB pages to be registered per XRI
to contain the exchanges Scatter/Gather List. This caps the number of SGL
elements that can be in the SGL. There are not extensions to extend the
list out of the 2 pages.
The G7 hardware adds a SGE type that allows the SGL to be vectored to a
different scatter/gather list segment. And that segment can contain a SGE
to go to another segment and so on. The initial segment must still be
pre-registered for the XRI, but it can be a much smaller amount (256Bytes)
as it can now be dynamically grown. This much smaller allocation can
handle the SG list for most normal I/O, and the dynamic aspect allows it to
support many MB's if needed.
The implementation creates a pool which contains "segments" and which is
initially sized to hold the initial small segment per xri. If an I/O
requires additional segments, they are allocated from the pool. If the
pool has no more segments, the pool is grown based on what is now
needed. After the I/O completes, the additional segments are returned to
the pool for use by other I/Os. Once allocated, the additional segments are
not released under the assumption of "if needed once, it will be needed
again". Pools are kept on a per-hardware queue basis, which is typically
1:1 per cpu, but may be shared by multiple cpus.
The switch to the smaller initial allocation significantly reduces the
memory footprint of the driver (which only grows if large ios are
issued). Based on the several K of XRIs for the adapter, the 8KB->256B
reduction can conserve 32MBs or more.
It has been observed with per-cpu resource pools that allocating a resource
on CPU A, may be put back on CPU B. While the get routines are distributed
evenly, only a limited subset of CPUs may be handling the put routines.
This can put a strain on the lpfc_put_cmd_rsp_buf_per_cpu routine because
all the resources are being put on a limited subset of CPUs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added code to support driver loopback with MDS Diagnostics. This style of
diagnostics passes frames from the fabric to the driver who then echo them
back out the link. SEND_FRAME WQEs are used to transmit the frames. Added
the SOF and EOF field location definitions for use by SEND_FRAME.
Also ensure that enable_mds_diags is a RW parameter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To aid better hardware detection when there are issues, report the first
and second level hardware revisions from the READ_REV command. Add the
elements to the existing hardware id string.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to see real addresses, convert %p with %px for kernel addresses
and replace %p with %pf for functions.
While converting, standardize on "x%px" throughout (not %px or 0x%px).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While performing code review, several relatively simple optimizations can
be done in the fast path.
Add these optimizations (unlikely designators).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Running on Coverity produced the following errors:
- coding style (indentation)
- memset size mismatch errors
note: comment cases where it is purposely a mismatch
Fix the errors.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
modinfo for lpfc_nvme_enable_fb is incorrect. FirstBurst on lpfc target is
not fully supported.
Update the attribute description
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is allowing the user to change lpfc_enable_bg while loading the
driver against a FCoE adapter. This is not supported.
No check is made for the adapter type when applying the blockguard
enablement value.
Fix by verifying the adapter type before setting the enablement flag.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
GetTrunkInfo is displaying an incorrect link speed when the link is a trunk
and the link has gone down. The driver is not clearing the logical speed
as part of the link down transition.
Fix by setting the logical speed to UNKNOWN SPEED when the link goes down.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Max Frame Size value is shown as 34816 in fdmishow from Switch.
The driver uses bbRcvSize in common service param which is obtained from
the READ_SPARM mailbox command. The bbRcvSize field which is displayed is a
three nibble field but the driver is printing a full four nibbles.
Fix by masking off the upper nibble.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The scsi transport fc bsg interface does not expect the bsg_job_done()
callback to be done if the bsg request call returns failure. Several of the
HST_VENDOR cases in the driver unconditionally call bsg_job_done()
regardless of the returning value.
Fix the code to only call bsg_job_done() if the call to lpfc_bsg_request()
will return success.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When forcing the use of MSI (vs MSI-X) the driver is crashing in
pci_irq_get_affinity.
The driver was not using the new pci_alloc_irq_vectors interface in the MSI
path.
Fix by using pci_alloc_irq_vectors() with PCI_RQ_MSI in the MSI path.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently reporting a non-zero nvme sg_seg_cnt value of 256
when nvme is disabled. It should be zero.
Fix by ensuring the value is cleared.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an unsolicited ABTS was received, the driver looks up the exchange it
references. It it does various searches looking for the exchange
context. When one is eventually matched and it is associated with an XRI
context, the driver sends an ABORT WQE to terminate the exchange. Current
code looks at whether the transport had taken action on the XRI yet or not
(no action if set to LPFC_NVMET_STE_RCV; action if non-LPFC_NVMET_STE_RCV).
Based on action or not one of two (sol vs unsol) issue abort routines are
called. The unsol version cheats and transmits a sequence containing an
ABTS with no interaction with the adapter. The sol version issues an Abort
WQE and lets the adapter manage whether the ABTS is sent to not.
The issue is the unsol version is sending ABTS unconditionally for the
exchange that received the ABTS. It's unnecessary.
Remove the conditional and just call the adapter command-based routine to
let the adapter manage the ABTS.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As part of firmware download, the adapter is reset. On the adapter the
reset causes the function to stop and all outstanding io is terminated
(without responses). The reset path then starts teardown of the adapter,
starting with deregistration of the remote ports with the nvme-fc
transport. The local port is then deregistered and the driver waits for
local port deregistration. This never finishes.
The remote port deregistrations terminated the nvme controllers, causing
them to send aborts for all the outstanding io. The aborts were serviced in
the driver, but stalled due to its state. The nvme layer then stops to
reclaim it's outstanding io before continuing. The io must be returned
before the reset on the controller is deemed complete and the controller
delete performed. The remote port deregistration won't complete until all
the controllers are terminated. And the local port deregistration won't
complete until all controllers and remote ports are terminated. Thus things
hang.
The issue is the reset which stopped the adapter also stopped all the
responses that would drive i/o completions, and the aborts were also
stopped that stopped i/o completions. The driver, when resetting the
adapter like this, needs to be generating the completions as part of the
adapter reset so that I/O complete (in error), and any aborts are not
queued.
Fix by adding flush routines whenever the adapter port has been reset or
discovered in error. The flush routines will generate the completions for
the scsi and nvme outstanding io. The abort ios, if waiting, will be caught
and flushed as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This issue is specific to SLI-3 adapters, specifically when DIF is used.
Once seen, this message floods the logs:
9064 BLKGRD: lpfc_scsi_prep_dma_buf_s3: Too many sg segments from
dma_map_sg
The driver, upon detecting an error such as too many elements in an sglist,
misrepresents the error by treating it as a temporary resource issue by
returning MLQUEUE_HOST_BUSY. In these cases, no retry will fix it and it
should have been a hard error. The repeated retry was causing the spamming
of the log.
As for the initial reason of why an I/O encountered this issue at all is
not clear as parameters set by the driver should have avoided this. The
dm multipath maintainer has been notified of the issue.
Fix by changing the return code for the dma mapping routines to indicate
cases that are not retryable and return DID_ERROR on those cases.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter encounters a condition which causes the adapter to fail
(driver must detect the failure) simultaneously to a request to the driver
to reset the adapter (such as a host_reset), the reset path will be racing
with the asynchronously-detect adapter failure path. In the failing
situation, one path has started to tear down the adapter data structures
(io_wq's) while the other path has initiated a repeat of the teardown and
is in the lpfc_sli_flush_xxx_rings path and attempting to access the
just-freed data structures.
Fix by the following:
- In cases where an adapter failure is detected, rather than explicitly
calling offline_eratt() to start the teardown, change the adapter state
and let the later calls of posted work to the slowpath thread invoke the
adapter recovery. In essence, this means all requests to reset are
serialized on the slowpath thread.
- Clean up the routine that restarts the adapter. If there is a failure
from brdreset, don't immediately error and leave things in a partial
state. Instead, ensure the adapter state is set and finish the teardown
of structures before returning.
- If in the scsi host reset handler and the board fails to reset and
restart (which can be due to parallel reset/recovery paths), instead of
hard failing and explicitly calling offline_eratt() (which gets into the
redundant path), just fail out and let the asynchronous path resolve the
adapter state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
