Change whitespace in the pin control drivers for R-Car H3 ES2.0+, R-Car
M3-W/M3-W+, and R-Car M3-N, to reduce the differences among these very
similar drivers.
These changes have no functional impact.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/527b45ebfc664a80e41cb0136677db7260e11437.1619785375.git.geert+renesas@glider.be
R-Car Gen3 Hardware Manual Errata for Rev. 0.52 of Nov 30, 2016, added
the configuration bit for bias pull-down control for the PRESET# pin on
R-Car M3-W. Add driver support for controlling pull-down on this pin.
Fixes: 2d40bd2427 ("pinctrl: sh-pfc: r8a7796: Add bias pinconf support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/c479de5b3f235c2f7d5faea9e7e08e6fccb135df.1619785375.git.geert+renesas@glider.be
Implement support for pull-up (most pins) and pull-down (ASEBRK#/ACK)
handling for R-Car M2-W and M2-N, and RZ/G1M and RZ/G1N SoCs, using the
common R-Car bias handling.
Note that on RZ/G1 SoCs, the "ASEBRK#/ACK" pin is called "ACK", but the
code doesn't handle that naming difference. Hence users should use the
R-Car naming in DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-7-geert+renesas@glider.be
Currently, the common R-Car bias handling supports pin controllers with
either:
1. Separate pin Pull-Enable (PUEN) and pin Pull-Up/Down control (PUD)
registers, for controlling both pin pull-up and pin pull-down,
2. A single pin Pull-Up control register (PUPR), for controlling pin
pull-up.
Add support for a variant of #2, where some bits in the single pin
Pull-Up control register (PUPR) control pin pull-down instead of pin
pull-up. This is the case for the "ASEBRK#/ACK" pin on R-Car M2-W,
M2-N, and E2, and the "ACK" pin on RZ/G1M, RZ/G1N, RZ/G1E, and RZ/G1C.
To describe such a register, SoC-specific drivers need to provide two
instances of pinmux_bias_reg: a first one with the puen field filled in,
listing pins with pull-up functionality, and a second one with the pud
field filled in, listing pins with pull-down functionality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-6-geert+renesas@glider.be
Add PORT_GP_CFG_7() and PORT_GP_7() helper macros, to be used by the
r8a7791 subdriver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-5-geert+renesas@glider.be
The pin control sub-drivers for SH/R-Mobile SoCs contain almost
identical bias handling. The only SoC-specific part is the mapping from
pin numbers to PORTnCR registers.
Reduce code duplication by factoring out the bias handling to the common
pinctrl.c code. Use a callback to handle the pin/register mapping.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-4-geert+renesas@glider.be
The Renesas Pin Function Controller driver uses two header files:
- sh_pfc.h, for use by both core code and SoC-specific drivers,
- core.h, for internal use by the core code only.
Hence move the R-Car bias helper declarations from core.h to sh_pfc.h,
and drop the inclusion of core.h from SoC-specific drivers that no
longer need it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-3-geert+renesas@glider.be
Now all R-Car pin control drivers have been converted to the common
R-Car bias handling, sh_pfc_pin_to_bias_reg() is only called from a
single place. Move it from core.c to pinctrl.c, make it static, and
rename it to rcar_pin_to_bias_reg(), as it is specific to R-Car SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-2-geert+renesas@glider.be
- Restrict debug runtime-checks to Renesas platforms,
- Initial support for the R-Car V3U SoC.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYAFgRQAKCRCKwlD9ZEnx
cEWIAP40TrUerqfnQgJ7iNYLh9WfSk48w9Gxzm92E7FanXaJBAD/dmkieXwQBBig
zKNuoWL2ZlK7O5MMkzpNnhLNS95SEQs=
=vIxg
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.12-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.12
- Restrict debug runtime-checks to Renesas platforms,
- Initial support for the R-Car V3U SoC.
Add pins, groups and functions for the 16-Bit Timer Pulse Unit outputs
on the R-Car R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210112165929.31002-13-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and function for the Interrupt Controller for External
Devices (INTC-EX) on the R-Car R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210112165929.31002-7-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds HSCIF0-3 pins, groups and functions to the R8A779A0
(V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165929.31002-6-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds groups and function for AVB PHY, LINK, MAGIC, RGMII and
PTP pins for the R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165929.31002-3-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C0-6 pins, groups and functions to the R8A779A0 (V3U)
SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165929.31002-2-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds SCIF0, 1, 3 and 4 pins, groups and functions for the
R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165912.30876-6-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds initial pinctrl support for the R8A779A0 (V3U) SoC,
including bias, drive strength and voltage control.
Based on patch by LUU HOAI <hoai.luu.ub@renesas.com>.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165912.30876-5-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds config macros describing the voltage levels available on
a pin. The current default (3.3V/1.8V) maps to zero to avoid having to
change existing PFC implementations.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165912.30876-3-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The V3U SoC has several unlock registers, one per register group. They
reside at offset zero in each 0x200 bytes-sized block.
To avoid adding yet another table to the PFC implementation, this
patch adds the option to specify an address mask instead of the fixed
address in sh_pfc_soc_info::unlock_reg.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165912.30876-2-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When DEBUG is defined (e.g. if CONFIG_DEBUG_PINCTRL=y), the Renesas pin
control driver runs sanity checks against the pin control tables. This
may cause lots of output on the console, and can be annoying in ARM
multi-platform kernels. Fix this by only running the checks when
running on SuperH, or on a DT platform supported by the Renesas pin
controller driver.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210111165013.496897-1-geert+renesas@glider.be
Remove all empty lines at the end of functions in pinctrl subsystem,
and make the code neat.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Zhaoyu Liu <zackaryliu@yeah.net>
Link: https://lore.kernel.org/r/X98NP6NFK1Afzrgd@manjaro
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The only usage of sh73a0_vccq_mc0_ops is to assign its address to the
ops field in the regulator_desc struct, which is a const pointer. Make
it const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201109221012.177478-1-rikard.falkeborn@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On SuperH and ARM SH/R-Mobile SoCs, the pin control driver handles
GPIOs, too. To reduce code size when compiling a kernel supporting only
modern SoCs, most, but not all, of the GPIO functionality is protected
by checks for CONFIG_PINCTRL_SH_FUNC_GPIO.
Factor out the remaining parts when not needed:
1. sh_pfc_soc_info.{in,out}put describe GPIO pins that have input
resp. output capabilities (SuperH and SH/R-Mobile).
2. sh_pfc_soc_info.gpio_irq{,_size} describe the mapping from GPIO
pins to interrupt numbers (SH/R-Mobile).
3. sh_pfc_gpio_set_direction() configures GPIO direction, called from
the GPIO driver through pinctrl_gpio_direction_{in,out}put()
(SH/R-Mobile). Unfortunately this function cannot just be moved to
drivers/pinctrl/renesas/gpio.c, as it relies on knowledge of
sh_pfc_pinctrl, which is internal to
drivers/pinctrl/renesas/pinctrl.c.
While code size reduction is minimal, this does help in documenting
depencies.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-9-geert+renesas@glider.be
Currently, the rcar_pinmux_[gs]et_bias() helpers handle only SoCs that
have separate LSI Pin Pull-Enable (PUEN) and Pull-Up/Down Control (PUD)
registers, like R-Car Gen3 and RZ/G2. Update the function to handle
SoCs that have only LSI Pin Pull-Up Control Register (PUPR), like R-Car
Gen1/Gen2 and RZ/G1.
Reduce code duplication by converting the R-Car M1A pin control driver
to use the common handler.
Note that this changes behavior in case the (invalid!) option
"bias-pull-down" is used in an R-Car M1A DTS: before, it was ignored
silently; after this change, it is considered the same as
"bias-pull-up".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-8-geert+renesas@glider.be
The handling of the LSI Pin Pull-Up Control Registers (PUPR) on R-Car
M1A uses register offsets instead of register physical addresses.
This is different from the handling on other R-Car parts.
Convert the bias handling from register offsets to physical addresses.
This increases uniformity, and prepares for consolidation of the bias
handling.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-7-geert+renesas@glider.be
Shrink sh_pfc_pin_config from 8 to 2 bytes:
- The mux_set flag can be removed, as a non-zero mark value means the
same (zero = PINMUX_RESERVED is an invalid mark value),
- The gpio_enabled flag needs only a single bit,
- Mark values are small integers, and can easily fit in a 15-bit
bitfield.
This saves 6 bytes per pin when allocating the sh_pfc_pinctrl.configs
array, i.e. it reduces run-time memory consumption by ca. 1.5 KiB.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-5-geert+renesas@glider.be
On arm64, pointer size and alignment is 64-bit, hence a 4-byte hole is
present in between the enum_id and name members of the sh_pfc_pin
structure. Get rid of this hole by sorting the structure's members by
decreasing size.
This saves up to 1.5 KiB per enabled SoC, and reduces the size of a
kernel including support for all R-Car Gen3 SoCs by more than 10 KiB.
This has no size impact on SH and arm32.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-4-geert+renesas@glider.be
This driver supports both RZ/G1[MN] and R-Car M2-W/M2-N SoCs.
Optimize pinctrl image size for RZ/G1[MN], when support for R-Car
M2-W/M2-N (R8A779[13]) is not enabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201019124258.4574-7-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
