This patch changes the wording of the flow director add/remove and
asynchronous failure messages to include fd_id to try and add some
way to track the operations on a given fd_id. Its not perfect, but
its better than what we had as PCTYPE can apply to several different
filter requests.
This patch also removes a redundant message when filter
addition fails due to full condition.
Change-ID: Icf58b0603d4f162d9fc542f11a74866a907049f2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO and hw checksums.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.
Fix this by using vlan_get_protocol() helper.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The receive hang detection routine was never being run when
PTP was enabled.
Change-ID: I200f35b0f3190d31b595df89d678f4c8a2131ba0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some functions we might be doing potential dereference
without a check. This patch puts the check in place for all these
functions. Also fix the "for loops" so that we increment VF at the
right place so that we always do it even if we are short-circuiting
the loop through continue.
Change-ID: Id4276cfb1e841031bb7b6d6790c414242f364a9f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Whenever we get a Tx hang we issue a PFR, which means we send AQ
messages to VFS about the reset coming. Unfortunately with the recent
fix to be able to send messages to all VFS which earlier was not
happening at all we now are sending messages to not just the VFS that
are up but also to VFS that are not up. AQ complains about this and
sends us an error in ARQ called LAN overflow event for a queue. We
check if the queue belongs to a VF and if it does we try to send a
vc_notify_vf_reset message to that VF. Well if the VF is not up/enabled
we will be entering this function with a non-active VF id. In this
function we were assuming VF struct is populated but it won't be if
the VF is not active.
Change-ID: Ic6733cda4582d3609fe6d83b2872bb2dcdc73f4a
Signed-off-by: Ashish N Shah <ashish.n.shah@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct typo in the name of the type given to sizeof. Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/). The
semantic patch used can be found in message 0 of this patch series.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes the following sparse warnings:
drivers/net/ethernet/intel/i40e/i40e_nvm.c:254:13: warning:
symbol 'i40e_write_nvm_aq' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix missing include in Intel i40e driver. Without this include linux next
tree won't compile.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All other add functions for lists have the new item as first argument
and the position where it is added as second argument. This was changed
for no good reason in this function and makes using it unnecessary
confusing.
The name was changed to hlist_add_behind() to cause unconverted code to
generate a compile error instead of using the wrong parameter order.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [intel driver bits]
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the ability of a VF to set unicast promiscuous mode.
Considered to be a security risk to allow VFs to receive traffic
intended for other VFs so don't allow it, simply ignore the flag.
Also fix it to send the correct seid to aq for multicast promiscuous set.
Change-ID: Icb9c49a281a8e9d3aeebf991ef1533ac82b84b14
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes comment for reset reason
Change-ID: I6fda4fa292255e6eb0f874502b4d38d722149b10
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local loopback should only be enabled for VSIs that are supporting
cascaded VEBs or VEPA setups. This is not the case here, and we need
to stop the VEB from echoing the VMDQ VSI packets back at the VSI.
Change-ID: I9dfb6ac79db24d04360d7efde62d81e20abc5090
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vf_id needs to be offset by the vf_base_id from hw function capabilities
for the case of multiple PFs.
Change-ID: I20ca8621f98e9cdf98649380b8eeaa35db52677c
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the HW registers are no longer in debug mode and many are
locked down for writes, we need to expose the Firmware API request
used to do writes on the driver's behalf.
Change-ID: I09a05c4dc9ea0b24c00193faac34d7799eaa8496
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds newly added FCoE files to the build but only if FCoE module is configured.
Also, updates i40e document for added FCoE support.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds FCoE specific code to existing i40e core driver to:-
1. have separate FCoE VSI with additional FCoE queues pairs.
2. have FCoE related hash defines.
3. have additional FCoE related stats code.
4. export and then re-use existing functions required by FCoE build.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds FCoE ( Fibre Channel Over Ethernet ) code for
Intel XL710 adapters. This patch is limited to only new FCoE
offloads code in newly added files by this patch and then
following patches in the series modifies rest of the existing
driver to enable FCoE with i40e driver.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes the AQTX answer comes back with no data, but we still want to print
the descriptor that got written back.
Change-ID: I5f734d99b4c95510987413893f0a34626571d474
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Give link a little more time to come back up after setting flow control
before resetting. In the new NVMs it is taking longer for link to come back.
This causes the driver to attempt to reset the link, which then errors
because the firmware was already in the middle of a reset. Also, initialize
err to 0.
Change-ID: I1cc987a944e389d8909c262da5796f50722b4d6b
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jmyoungx@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reword the error messages. Also add a major version check because
We only want to warn on nvm_minor > expected_minor if
nvm_major == expected_major. Lastly, change an if to an else if
because the two statements will never evaluate to true at the same time.
Change-ID: I6ddf9986f26b35f6879cbeac4fcef04a8497a383
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Copy desc and buffer data even for ARQ events which return error status.
Previously, a check for NVM related AQ commands which is done later in this
function would not recognize that such a command was received and would
not clear nvm_busy flag. This would block access to NVM until a driver reset.
This will fix that.
Change-ID: If69ad74e165b56081c0686b97402511d2e2880c0
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware design requires that the driver avoid indicating
checksum offload success on some ipv6 frames with extension
headers.
The code needs to just check for the IPV6EXADD bit and if
it is set punt the checksum to the stack. I don't know why
the code was checking TCP on inner protocol, as that code
doesn't make any sense to me but seems wrong, so remove it.
Change-ID: I10d3aacdbb1819fb60b4b0eb80e6cc67ef2c9599
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This implements a state machine intended to support the userland tool for
updating the device eeprom. The state machine implements one-shot reads,
writes, multi-step write sessions, and checksum requests. If we're in the middle
of a multi-step write session, no one should fire off other writes, however, one
shot reads are valid. The userland tool is expected to keep track of its session
status, arrange the placement and ordering of the writes, and deal with the
checksum requirement.
This patch also adds nvmupdate support to ethtool callbacks.
The get_eeprom() and set_eeprom() services in ethtool are used here to
facilitate the userland NVMUpdate tool. The 'magic' value in the get and
set commands is used to pass additional control information for managing
the read and write steps.
The read operation works both as normally expected in the standard ethtool
method, as well as with the extra NVM controls. The write operation
works only for the expanded NVM functions - the normal ethtool method is
not allowed because of the NVM semaphore management needed for multipart
writes, as well as the checksum requirement.
Change-ID: I1d84a170153a9f437906744e2e350fd68fe7563d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
spotted by cppcheck
Signed-off-by: Toralf Förster <toralf.foerster@gmx.de>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Display a verbose warning message when the incorrect PF attempts to
control timestamping for a port to which it was not assigned. This
shouldn't display except in the case of multiple PFs per port. The
primary intent of this message is to help debugging the reason why the
SIOCSHWTSTAMP ioctl has failed, and to help narrow the cause of the
issue.
Change-ID: Ic98798e0c844d98389d4c20e7160ba256f2bc7e8
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. Remove some break statements that will never get touched.
2. Remove an extra space.
3. Remove a comment for a parameter that doesn't exist
4. Move the assignment of a variable up to get rid of an else case.
Change-ID: I308a4b5ec070b1f0601f13b041ba4375aaad4b06
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e has a single set of TX time stamping resources per NIC.
Use a simple bit lock to avoid race conditions and leaking skbs
when multiple TX rings try to claim time stamping.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
skb_tx_timestamp() does not report software time stamp
if SKBTX_IN_PROGRESS is set. According to timestamping.txt
software time stamps are a fallback and should not be
generated if hardware time stamp is provided.
Move call to skb_tx_timestamp() after setting
SKBTX_IN_PROGRESS.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a new API to get the port mac address from firmware.
It also adds support to the ndo_get_phys_port_id() callback to provide
port specific unique id to the netdev layer.
If the adapter has a valid per-port mac address then that
would be used for this purpose and is expected to be unique
on a per-port basis.
The information can be viewed by reading the phys_port_id
attribute in sysfs for each netdev or via IF netlink
interface.
Change-ID: I341fa6fff9c112f1f6d987189309e730e0b50e8b
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dumping a bridge fdb dumps every fdb entry
held. With this change we are going to filter
on selected bridge port.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump.
Change-ID: Ie0c36583ffd9997679f46bdf89bc462d3e992995
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement set_settings for ethtool in i40e.
Change-ID: Ie3c3fe18e8ff86c3f25b842844b3d9aabc9bba57
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add i40e implementation of setpauseparam to ethtool.
Change-ID: Ie7766b2091ec8f934737573c9ffd426081966718
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add function set_fc to set the requested FC mode. This patch also
adds the init of FC setting to get_link_info and replaces the init
code to set FC off by default in main. Also adds i40e_set_phy_config
to support this.
Change-ID: I7b25bbaec81f15777137ab324a095f916e44351d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just move nway reset up, will be used in the next patch.
Change-ID: Ice3b631fa2044debc5c4541b42872a48163f8452
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a new variable, hw.phy.link_info.an_enabled, to track whether autoneg is
enabled. Also add a new function update_link_info that will update that
variable as well as calling get_link_info to update the rest of the link info.
Also add get_phy_capabilities to support this.
Change-ID: I5157ef03492b6dd8ec5e608ba0cf9b0db9c01710
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Finish the i40e implementation of get_settings for ethtool.
Change-ID: Iec81835aa9380723ae9288bcb79b30a6a1ecd498
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
TPH is not currently enabled in this product, make sure it
isn't enabled by default.
Change-ID: Ibb1a10799c33c4c76dec06fcd53b1d6efa13c1f5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When turning off ntuple with a FD table full situation,
the driver would have auto disabled FD filter additions.
Clear the auto disable flag for FD_SB so that when the
feature is turned on again using "ethtool -K ethx ntuple on"
we can start adding filters once again.
Change-ID: I036a32e7331bcae765b657c8abb4fa070940b163
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the AQ interrupt gets lost for some reason, VF communications will
stall as the VFs have no way of reaching the PF, which is essentially
deaf. The VFs end up waiting forever for a reply that will never come.
To alleviate this condition, go ahead and check the ARQ every time we
run the service task. Remove the check for a pending event, and get rid
of a chatty error message that is now meaningless.
Change-ID: I0fc9d18169cd45c98f60188aef872cd6cee9a027
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Force a shifted '1' to be unsiged to avoid shifting a signed int
Change-ID: I688cbd082af0f2e1df548fda25847a5ca04babcf
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The HW still needs to consume it and freeing it in the function
that created it would mean we will be racing with the HW. The
i40e_clean_tx_ring() routine will free up the buffer attached once
the HW has consumed it. The clean_fdir_tx_irq function had to be fixed
to handle the freeing correctly.
Cases where we program more than one filter per flow (Ipv4), the
code had to be changed to allocate dummy buffer multiple times
since it will be freed by the clean routine. This also fixes an issue
where the filter program routine was not checking if there were
descriptors available for programming a filter.
Change-ID: Idf72028fd873221934e319d021ef65a1e51acaf7
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need the export.h header so we can just go ahead and remove it.
Change-ID: I9057396b141ee449d8299409081358b9270a7c4d
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prevent writing to reserved bits, queue index is 0-127
Change-ID: Ic923e1c92012a265983414acd8f547c4bdac2e34
Signed-off-by: Christopher Pau <christopher.pau@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver needs to initialize all members of context descriptor. Stale
data is possible otherwise.
Change-ID: Idc6b53af45583509da42d5ec0824cbaf78aee64f
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the auto_disable flags added there was a bug that was causing the
replay logic to not work correctly.
This patch fixes the issue so that we call a replay after a sideband
reset correctly.
Change-ID: I005fe1ac361188ee5b19517a83c922038cba1b00
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new variable defining ASQ command write back timeout to allow for
dynamic modification of this timeout. Initialize it on AQ initialize
routine with default value, vary it on device ID.
Change-ID: I5c9908f9d7c5455634353b694a986d6f146d1b9d
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make mask value of all 1s. Value of -1 can't be used for u32 type.
Change-ID: I49d58b77639939fe7447a229dbf1f4a1bf7419ce
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Per a recent HW designer comment, this code is for ripping through the
queues and interrupts to fully disable them on driver init, specifically
to help clean up after a PXE or other early boot activity.
Change-ID: I32ed452021a1c2b06dace1969976f882a37b9741
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the AQ BAH and BAL registers on a clean shutdown to help make sure
all is tidy when the driver is done.
Change-ID: I393e92680247daa52a8e00bab183213672d73578
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Base Address High and Low to the admin queue struct to simplify
another bit of "which context" logic in the config routines.
Change-ID: Iae195a7da3baffc1a9d522119e1e2b427068ad07
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were a couple of fields in the fdir descriptor setup that
were not being reprogrammed, which left the opportunity for stale
data to be pushed as part of the descriptor next time it was used.
Change-ID: Ieee5c96a7d4713d469693f086c4854de949a7633
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"fd current cnt" can be used to print the total filters consumed
by this interface, this includes guaranteed and best effort filters.
Change-ID: I2c417810c4999ce1388d2ea26f8e69679ba33966
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware does not have a way of telling a PF how much of the global
shared FD table space is still available or is consumed.
Previously, every PF but PF0 would think there was still space available
when there wasn't. The PFs would continue to try to add filters and fail.
With this new logic if a filter programming error is detected we just
check if we are close to the guaranteed space full and that can be used
as a hint to say, there might not be space and we should turn off the
features. This way we can turn off the feature in SW for all PFs in
time.
Change-ID: I725cb2fab16c033f883056362b4542c1400503c5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There wasn't a need to play the logic twice, it seems
like a left over from when we had to add two PTYPEs for
one filter. There should be no change in the number of
filters that actually got added to the hardware.
Change-ID: I5071d02eafd020b60e30eb96219f110f334eec85
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently every time we run through the i40e_ptp_init routine, we create
a new device node. This function is called by i40e_reset_and_rebuild
which is used to handle reset of the device. Even though the 1588
registers only get cleared on a GLOBAL reset, this function is still
called to handle a CORE reset.
This causes a leak of PTP device nodes at every reset. To fix this,
break PTP device clock node creation out of i40e_ptp_init, and only call
this if we don't already have a device created. Further invocation of
i40e_ptp_init will not generate new PTP devices. Instead, only the
necessary work required to reconfigure 1588 will be done.
This change also fixes an issue where a reset can cause the
device to forget it's timestamp configuration, and revert to the default
mode.
Change-ID: I741d01c61d9fe1d24887859d1316e1a8a892909e
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch prevents the SIOCGHWTSTAMP ioctl from possibly returning bad
data, by not permanently storing the setting into the private
structure until after we've finished validating that we can support it.
Change-ID: Ib59f9b4f73f451d5a2e76fb8efa5d4271b218433
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch facilitates future work by breaking the PTP hardware control
bits out of the i40e_set_ts_config function. By doing this, we can
maintain state about the 1588 timestamping mode and properly re-enable
to the last known mode during a re-initialize of 1588 bits.
This patch also modifies i40e_ptp_init to call the
i40e_ptp_set_timestamp_mode during the reconfiguration process. A
future patch will ensure that the hwtstamp_config structure is not reset
during this process, so that timestamp mode will be maintained across a
reset.
Change-ID: Ic20832c96c5c512ac203b6c7534e10d891c560f0
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduces possible confusion and ambiguity in purpose of the ancillary
feature control entry point function.
Change-ID: I21d773c1a86878f6d061505185b596c788d1b7cc
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix HMC handling for big endian architectures.
Change-ID: Id8c46fc341815d47bfe0af8b819f0ab9a1e9e515
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We do not need to acquire NVM for Shadow RAM XSUM calculation, as we only
read from SR through SRCTL register for which having the ownership is not
required.
Change-ID: Ie238a8f09917d1d25f24cc7cec271951ac7b98f2
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a Tx hang happens, usually the Tx queue disable fails. At
this point if we try to recover by a VSI reinit the HW gets
unhappy and we get a Malicious Driver Detect (MDD) event.
HW expects a PF reset if a queue disable fails, if we don't do a PF
reset and restart the queue we get an MDD. This patch makes sure we
do a PF reset on Tx hang and that way we avoid any MDD because of Tx
queue disable failure.
Change-ID: I665ab6223577c788da857ee2132e733dc9a451e4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF reset to clean up at the end of the remove is a nice thing
to do, but it also removes any LAA setting that Wake On LAN wants
for future wake up.
Change-ID: Ic090ec714df2d722281d11735cf75f2aa4432e2c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The LAA is lost on a reset, so be sure to replay it when rebuilding
the switch after any reset.
Change-ID: I6e643f9a59dfd899b6cbdf84d93b4bc9c37bb949
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't short-circuit the LAA assignment when the driver thinks it has
already been done - it is possible that the user might want to force
the address setting again. At the same time, this requires a little
re-ordering of the filter management.
Change-ID: Ia0d71e3bc04edd7b68cf67edecc00abe7b9f6639
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the Firmware sets up the LAA as a Wake-On-LAN address.
Change-ID: I57b9acd8c288424fcfed0911053eb725c400b41c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ability is already there in the fw and this will make it easy
to toggle link without calling set_phy_config when no other link
settings need to change.
Change-ID: I185567ae81776382ac145247e4eb1ee95f22382c
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the PCTYPES that was moved to a reserved value
wasn't removed from the code.
Change-ID: I31fafe6d79c5f5128179979af5eaafa8c0cd62fe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the i40e_set_coalesce function to allow 0 as a disable
value. Also, added message to user about invalid value and provides valid
range.
Change-ID: I6c9ff11a9861f2045bd543745a3d132999ffbbd8
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This log print message will probably never be seen, but it needs to match
the "attempting to rebuild switch\n" log message a few lines above.
Change-ID: Ic3f5b4f67568d721cb02e826cf2cb33847f51c11
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the firmware's API minor number is larger than the one expected, log
a warning and recommend driver SW update.
If the firmware's API major or minor number is smaller then the one expected
(n for major, n or n-1 for minor), log a warning and recommend NVM update.
Change-ID: If0b887e055478f8e435ba7fa28113b63a6f1bb35
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per the spec when the PF driver receives a Malicious driver event
the queue that caused the event is already stopped and it is expected
that the function that owns the queue will reset the queue.
In some cases it may not be possible to determine the queue and it is
suggested to reset the whole function.
This patch takes the later approach when the event is owned by the PF
that owns it.
Change-ID: I40f9764a6a5e068c0ef8438db00c5aa9c2c6c1c8
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The return from i40e_prep_for_reset() was being ignored by almost all
its callers. The one place it wasn't ignored could have caused a silent
and confusing failure of the driver to finish a reset. Since we really
are doing a rebuild anyway, ignore this last case as well and simply
make the function a void type.
Change-ID: Ia4fed7f903d39a6c47c5722625a53e59c3f7ed53
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the host VMM administrator has changed the VF device's MAC address then
the i40e driver needs to halt the VF device so that the administrator will
be forced to reload the VF driver. This will cause the VF driver to start
using the newly assigned MAC address. This brings the i40e driver into
conformance with operational characteristics of other Intel SR-IOV
featured drivers.
Change-ID: Ic7242cceb8287dd2cb72fb1f3166a032a28bf88a
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some AQ debug prints needs be moved around or do additional checks so they
will not cause our tool applications to cause segmentation faults.
The tools run in user space and we need to correctly reference kernel
space memory.
Change-ID: Ia2ac4076f576b805f350453fd50ad69c2a91ab9a
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the RSS configuration to set table size
and write to hardware to confirm RSS table size being used.
Change-ID: I455a4c09c9dd479f5791ee1f09fdc83ff9908df5
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the service tasks don't try to meddle with the
device while a reset is in progress. Odd things can happen
such as funky stats values.
Change-ID: I6929cb9d6d96839c9279362ca7c0e3fe6c8fcc66
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VEB really is part of the whole PF and should be cleared
at the same time.
Change-ID: Ia1d4d1df5cf421f2578a22486650dd256cc4617a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The bug is encountered when all the Tx hang recovery mechanisms have
failed and driver tries to bring down the interface in the interrupt context.
The patch defers this and schedules it for next cycle.
Change-ID: Id9cd1da15b0e5c018dce18da4d0eed5ef1e8a809
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the debugfs command "lldp get remote" that dumped the local
LLDPDU instead of peer's LLDPDU.
Change-ID: I0702eacdafd54478c18f20cab3a7fa5dc1b3182d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce helper routines that would wait for the Rx/Tx queue
to reach the enable or disable state as requested.
Change-ID: I518d9d0e2afef3f45107af3b46e9af402ff587c3
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we resize the number of queues, the driver needs to disassociate any
qvectors that are no longer in use from the original rings, this way we
do not try to access the rings through these qvectors at the time of freeing
the qvectors.
Change-ID: Ie4eb9fc749f8e12348517fe1560f599c58f4a2a4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reset head and tail on admin queue initialization where H/T are
not reset by HW.
Change-ID: I6db8a2dd3f05ce66410a92cce016191add04760e
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM wasn't filling in the GLQF_HKEY register on
some old NVM versions. If this is the case, fill
in some values so receive with flow rules works right.
Change-ID: Ic737888ee68f96efb4cf8a1a49d2301615e09ed2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This updates the register file for new hardware.
The format of the file has changed requiring drivers to
declare I40E_MASK. I40E_MASK is to be used with 32 bit registers.
This patch also updates the drivers to accommodate the register changes.
Change-ID: If9bc8d736391024cbf99054efe50f9acc12ee4f1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
No need to read the PCI register for the PF's base queue on every single Tx
queue enable and disable as we already have the value stored from reading
the capability features at startup.
Change-ID: Ic02fb622757742f43cb8269369c3d972d4f66555
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A drop action comes down as a ring_cookie value, so allow it as
a special value that can be used to configure destination control.
Also fix the output to filter read command accordingly.
Change-ID: I9956723cee42f3194885403317dd21ed4a151144
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add members to stat struct to keep track of Flow director ATR and
SideBand filter packet matches.
Change-ID: Ibbb31a53c7adcc2bb96991dd80565442a2f2513c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change drops the FTYPE field from the Rx descriptor, to
match the hardware implementation.
Change-ID: I66d31d2b43861da45e8ace4fb03df033abe88bab
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linux gives us a function to copy Ethernet MAC addresses, let's use it.
Change-ID: I0c861900029ca5ea65a53ca39565852fb633f6fd
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the filter created by the firmware with the default MAC address it
reads out of the NVM storage and a promiscuous VLAN tag and replace it
with a filter that will not accept tagged packets by default. The system
must request a VLAN tag packet filter to get packets with that tag.
Change-ID: I119e6c3603a039bd68282ba31bf26f33a575490a
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the firmware reports DCB capability the driver enables
I40E_FLAG_DCB_ENABLED flag. When this flag is enabled the driver
inserts a tag when transmitting a packet from the port even if there
are no DCB traffic classes configured at the port.
This patch adds a new flag I40E_FLAG_DCB_CAPABLE that will be set
when the DCB capability is present and the existing flag
I40E_FLAG_DCB_ENABLED will be set only if there are more than one
traffic classes configured at the port.
Change-ID: I24ccbf53ef293db2eba80c8a9772acf729795bd5
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In XL710 devices we program FD filter's fields from Tx perspective of the flow.
However the user interface exposed in ethtool should be compliant with the
previous generation of drivers where a filter src and dst field are from
the RX perspective. This patch changes the ethtool interface in this regard
to match the other drivers.
Change-ID: Iec6ccddd87357c4fb53ccf33aa0fae699faf70cf
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add set_pf_context, replace set_phy_reset with set_phy_debug, add
nvm_config_read/write, remove nvm_read/write_reg_se and add some
PHY types.
With these changes we bump the API version to 1.2.
Change-ID: I4dc3aec175c2316f66fc9b726b3f7d594699d84e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set appropriate fields in Tx queue configuration virtchnl message
to pf to enable headwb and setup headwb addr.
Then use that info from the VF to set headwb and headwb_addr instead of
always enabling them.
Change-ID: I7d393d1b2b07f0f3355b3a4f7c2d3c6ee3b0d622
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bumpity and Fred Worm say it's time to change the numbers again.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Change-ID: I658731d022ea23cedede4be2bfecd8b4cc68d270
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We tell the HW upper boundary of power of 2 in VSI config,
but the HW does not restrict us to use just power of 2 GPS in
case of RSS as long as we are not sharing the RSS table with
another VSI (VMDq). We at present are not doing RSS in VMDq
VSI.
If we were to enable that and if the system had CPU count which
was not power 2, the VMDq VSIs will see a little skewed distribution.
Change-ID: I3ea797ce9065a3ca4fc4d04251bf195463410473
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delete all the old and stale MAC filters for the VF VSI when the host
administrator changes the VF MAC address from under its feet. Also don't
bother to add a filter for the VSI when its going to go away anyway.
Just record the new address and punch the VF reset.
Change-ID: Ic0d12055926f41989d1965ccf500053729c063ad
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
FD_SB and FD_ATR needs to be checked independently in order to decide if
we will support multiple queues or not.
Change-ID: I9d3274f5924c79e29efdbcf66a2fcca1fee2107f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was not marking packets with bad checksums
correctly, especially IPv6 packets with a bad checksum.
To do this correctly we need a define that may be set by
hardware in rare cases.
Change-ID: I1a997b72b491ded27a78ac3bce1197b2d2611130
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify the logic in i40e_determine_queue_usage() so that
SR-IOV doesn't get turned off unnecessarily.
Change-ID: I86ca304fa9f742a50e9ea831b887f358a6a9d53d
Signed-off-by: Frank Zhang <frank_1.zhang@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the way resources are distributed to special features.
Change-ID: I847e49d714a1d70e97f3f994cb39bfb5e02ab016
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our hardware supports VF antispoofing for both MAC addresses and VLANs.
Enable this feature by default for all VFs and implement the netdev op
to control it from the command line.
Change-ID: Ifb941da22785848aa3aba6b2231be135b8ea8f31
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to complain in the log about mac addresses that
can't be deleted because they don't exist.
Change-ID: I4e6370df175bf72726f06d2206c03bcbfded8387
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This was a vestige of early driver development that no longer
has any actual use.
Change-ID: I95b5b19c4bbfaff8759197af671ebaf716cb6ab5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The number of VSIs that the firmware reports to us is a guaranteed
minimum, not an absolute maximum. The hardware actually supports far
more than the reported value, which we often need.
To allow for this, we allocate space for a larger number of VSIs than is
guaranteed by the firmware, with the knowledge that we may fail to get
them all in the future.
Note that we are just allocating pointers here, the actual (much larger)
VSI structures are allocated on demand.
Change-ID: I6f4e535ce39d3bf417aef78306e04fbc7505140e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for error status bits on the AdminQ event queue and announce them
if seen. If the Firmware sets these bits, it will trigger an AdminQ
interrupt to get the driver's attention to process the ARQ, which will
likely be enough to clear the actual issue.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Change-ID: I009e0ebc8be764e40e193b29aed2863f43eb5cb0
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 0.4.5 and i40evf to 0.9.29.
Change-ID: I9faca5544446518c5425612e733499cf16ef20a1
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove two device IDs 1582 and 1573, because they will not be shipped.
Change-ID: Ica2e550b5b21a69e3f353eba2fe5e1c532a548c4
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a coding error where during the registration for NAPI
the driver requested 256 budget. The max recommended
value for this is NAPI_POLL_WEIGHT or 64.
Change-ID: I03ea1e2934a84ff1b5d572988b18315d6d91c5c6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The TSO logic in the transmit path had some assumptions that
have been broken now that the kernel can send as much as 32kB
in a single skb->frag[.] entry, even on a system with 4kB pages.
This fixes the assumptions and allows the kernel to operate
as efficiently as possible with both SENDFILE and SEND.
In addition, the hardware limit of data contained in a descriptor is
changed to the next power of two below where it currently is in
order to align to a power of two value, preventing a single byte
of data in a descriptor.
Change-ID: I6af1f0b87c1458e10644dbd47541591075a52651
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Both the PF side and the VF side of the VF reset process are too noisy.
We already warn the user that a reset is happening, and that is
sufficient.
Because some of these message are inside if statements, we have to
rejigger the brackets at the same time to keep our coding style
consistent.
Change-ID: Id175562fb0ec7c396d9de156b4890e136f52d5f4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Once more, with feeling: not all VSIs have rings. To assume so is to
invite null pointers to your party.
Change-ID: I576858824468d9712d119fa1015a1f28c27712c4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Be sure to clear PXE mode bit on each reset after AdminQ has been rebuilt.
Change-ID: I992d8c79594f8ca0660c50844ace675ecb9c9bf2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where FD SB/ATR and NTUPLE configurations status are
reported erroneously. Without this patch, driver reports FDir without further
information.
Change-ID: I5bdd2871b7f2db1e5f5e76c741ae6a0dc603b453
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. There is no ixgbe_watchdog_task function in the driver, so change
the comment to the correct function name, i40e_watchdog_subtask.
2. Remove num_msix_entries from interrupt set_up routine
because it is never used.
3. Remove some TBD comments that are not needed.
Change-ID: I37697a04007074b797f85fd83d626672e4df1ad1
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove use of registers no longer supported.
Change-ID: I9d27399091cea78a926489d94f958edd762f5a20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As reported by Eric Dumazet, the driver is not masking the right
bits in the receive descriptor before it starts checking them.
This patch extends the mask to allow for the right bits to be
checked, and fixes the issue permanently via a define.
CC: Eric Dumazet <eric.dumazet@gmail.com>
Change-ID: I3274f7619057a950f468143e6d7e11b129f54655
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 0.4.3 and i40evf to 0.9.27.
Change-ID: I4141e9f8615bdcfa3b1b5ecbc2ac62603a03b7ad
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use an extra state variable to keep track of when the IRQs are fully
set up. This keeps us from trying to unhook IRQs that already were
left unhooked in a failed reset recovery, e.g. when firmware is broken.
Change-ID: I073eb081e4ef8aedcbdf1ee0717c0ed64fa172f2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a reset recovery failed (e.g. firmware is broken), the HMC space won't
get set up. We don't need to try to delete it if it didn't get set up.
This stops some needless error messages when we already know we need to
just tear things down.
Change-ID: Iac600481765e20b136052b43a544e55d7870268b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver should print link messages like all the
other Intel Ethernet drivers.
Change-ID: Ia88bdb96794e17a3962fcea94db176de01f921f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the missing unicast, multicast, and broadcast stats for the port.
Change-ID: Ifc366d7b7745f70eaac9d00eeb0694eb9ec076a9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add VSI HW stats for unicast, multicast, and broadcast for Rx and Tx.
Stop printing the netdev multicast value because it doesn't include Tx
and would be confusing.
Change-ID: I08278b6657e7c838fd29a4a1f305f78fe1b150be
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The wait time was originally too optimistic and the resets were failing
after EMPR. This increases the loop count to wait considerably longer.
This won't delay the actual wait longer than really needed, just allows
us to poll more times as needed.
Change-ID: If7b96f55cc25b8d06cbbe8665259d250188c53d7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a function which indicates our intention to enable or disable a particular
Tx queue. Also add a function to notify the device's Tx unit that we're about
to enable or disable a Tx queue.
Change-ID: I6adf3cbb5bb3e3c984d1ec969e06577c19ef296d
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
B0 Si blocks AQ registers when in Blank Flash mode - write is dropped,
read gives 0xDEADBEEF. Introduce a simple check for a correct value in one
of the AQ registers to be sure that AQ was configured correctly.
Without this check we get into an endless loop while trying to send
GetVersion AQ cmd.
Change-ID: I00102b8c5fa6c16d14289be677aafadf87f10f0d
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver and hardware are not expected to work correctly
with revision_id 0 hardware. Don't prevent the user from
using it, but be sure to print a warning.
Change-ID: I3712d34752bfad458078a5f35dfd0aa0ae9fd20e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print the VEB statistics in the ethtool stats output.
Change-ID: Ic93d4c3922345c43e4cfd7f7e7a906844dd2f49f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the VEB is created for the basic LAN device and its VSIs, we need to
set the tracking lan_veb index for later use.
Change-ID: I66bb74993bbda3621ca557437cb4b3517f9b315b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a couple more statistics that the hardware offers but aren't part
of the standard netdev stats.
Change-ID: I201db2898f2c284aee3d9631470bc5edd349e9a5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rx_errors (GLV_REPC) and rx_missed (GLV_RMPC) were removed
from the chip design.
Change-ID: Ifdeb69c90feac64ec95c36d3d32c75e3a06de3b7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull the PF stat collection out of the VSI collection routine, and
add a unifying stats update routine to call the various stat collection
routines.
Change-ID: I224192455bb3a6e5dc0a426935e67dffc123e306
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves some common code in two places into a
small helper function, and corrects a bug in one of the
two places in the process.
Change-ID: If3bba7152b240f13a7881eb0e8a781655fa66ce7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Structure for VEB context added. Update macro for
transition from ms to GTIME (us) time units.
Change-ID: Ib3a19587b4cf355348655df8f60c6f37bb1497a3
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, the PF driver only notifies the VFs for PF reset events.
Instead, notify the VFs for all types of resets, so they can attempt a
graceful reinit.
Change-ID: I03eb7afde25727198ef620f8b4e78bb667a11370
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was allowing the user to set larger size MTU
than the hardware was being configured to support.
The driver was already using VLAN_HLEN when setting the
hardware max receivable frame size, so just add it to the
netdev MTU set entry point as well.
Change-ID: Ie20e2a35d04f8c411253e255bea79ca69aaeaea3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unused defines and macros for RX_LRO.
Change-ID: I8ca6715edfa62b56837417a1c4ff68c2345dab6e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We introduced this check in case this structure changed in the future,
the AQ definition is now mature enough that this check is no longer necessary.
Change-ID: Ic66321d0a08557dc9d8cb84029185352cb534330
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Register range, being subject to register diagnostic, can vary among
different NVMs. We will try to identify the full range and use it for
a register test. This is needed to avoid false test results. If we fail
to define the proper register range we will test only the first register
from that group.
Change-ID: Ieee7173c719733b61d3733177a94dc557eb7b3fd
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A couple of FD checks ended up using bitwise OR to check
a value, which ends up always being evaluated to true.
This should fix the issue. Thanks to DaveJ for noticing
and reporting the issue!
CC: Dave Jones <davej@redhat.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
