The channel context structure is defined to enable
multi-channel concurrency support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename it to ath9k_cmn_init_channels_rates.
sbands are move to ath_common as well.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no benefit in retaining the legacy rate control module
in the driver codebase.
It is known to be buggy and has less than optimal performance
in real-world environments compared with minstrel. The only
reason that it was kept when we made the switch to minstrel
as default was that it showed higher throughput numbers in a
clean/ideal environment.
This is no longer the case and minstrel can push ath9k to
the same throughput levels. In TCP, with 3-stream cards, more than
295 Mbps can be obtained in open air, with 2-stream cards,
210 Mbps is easily reached. To test performance issues,
instead of using a broken rate control module, it is better
to use the fixed-rate interface provided by mac80211 anyway.
The ath9k RC has not received any bug fixes in years and is
just bit-rotting away - this patch removes it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, rename node_stat to node_aggr.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Move definitions to spectral.h
* Move processing/debug code to spectral.c
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the WoW code to wow.c and compile it conditionally
based on CONFIG_ATH9K_WOW.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW routines to set various WoW registers are present
in wow.c. For some reason, it has been compiled as part
of the main ath9k.ko module all this time, when it should
really be part of ath9k_hw.ko. This patch renames the file to
ar9003_wow.ko and adds it to ath9k_hw.ko.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use CONFIG_ATH9K_TX99 to properly enclose the tx99 code
and make sure that it is not compiled as part of the driver
when it is not selected. Move the tx99 code to a new file tx99.c
and also add ATH9K_DEBUGFS as a dependency in Kconfig.
This reduces the module size on platforms like OpenWrt where
ATH9K_DEBUGFS is selected, but TX99 might be disabled.
Cc: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the DFS pattern detector code to the ath module so
the other Atheros drivers can make us of it. This makes
no functional changes.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k rate control algorithm has various architectural
issues that make it a poor fit in scenarios like congested
environments etc.
An example: https://bugzilla.redhat.com/show_bug.cgi?id=927191
Change the default to minstrel which is more robust in such cases.
The ath9k RC code is left in the driver for now, maybe it can
be removed altogether later on.
Cc: stable@vger.kernel.org
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add a new file wow.c which takes care of the hardware code
for WoW.
*program the descriptors and data words to periodically
send Keep Alive Frames.
*program the user defined patterns/masks and pattern length
in the hardware registers.
*'ath9k_hw_wow_enable' is called during the drivers suspend
callback which takes care of the following
- tracking wow event mask (to suppress spurious
wow events)
- properly configure suspend/resume WAR registers
- configure PCIE PM control register
- configure MAC WoW registers and their timeouts
- enabling wow configuration like magic packet,
user patterns based on users configuration
- configuring timeouts for KAL, beacon miss,
aifs, slot time, backoff
- create Keep Alive Pattern ('KAL')
*'ath9k_hw_wow_wakeup' is called during the drivers resume
callback which takes care of the following
- primary task is to find the reason for wakeup
from the wow status register
- configure/restore AR_PCIE_PM_CTRL register
- clear all WoW events
- configure/restore suspend/resume WAR registers
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And use a helper function to setup antennae after a reset.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add link.c and move all the link/connection monitoring
code to it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a DFS pattern detector to ath9k. It is fed with pulse events
by the radar pulse detector and reports in place whether a pattern
was detected. On detection, the result is reported as radar event to
the DFS management component in the upper layer.
Currently the ETSI DFS domain is supported with detector lines for
the patterns defined by EN-301-893 v1.5.1. Support for FCC and JP
will be added gradually.
To include the pattern detector, ath9k must be built with support
for DFS certified config flag set (CONFIG_ATH9K_DFS_CERTIFIED).
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of CONFIG_ATH9K_BTCOEX_SUPPORT in ath9k_hw
to provide a clean way of compilation without BTCOEX
support.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses CONFIG_ATH9K_BTCOEX_SUPPORT to conditionally
compile btcoex-related code in the driver core.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This initial DFS module provides basic functionality to deal
with radar pulses reported by the Atheros DFS HW pulse detector.
The reported data is evaluated and basic plausibility checks
are performed to filter false pulses. Passing radar pulses are
forwarded to pattern detectors which are not yet implemented.
(Some modifications to actually use ATH9K_DFS_DEBUGFS based on comments
from Julian Calaby <julian.calaby@gmail.com>. -- JWL)
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9462 chips have the capabilities to provoide bluetooth
profile information. For non-AR9462 btcoex chips, the BT
priority traffic was identified by periodically polling
the respective registers and updated dutycycle, stomptype,
etc. As AR9462 chip offers the BT profile informations,
let us make use of that to update aggregation limit,
dutycycle, stomptype and wieghtages.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Supported calibrations of radio retention table (RTT) are
- DC offset
- Filter
- Peak detect
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k only available in menuconfig if PCI bus
support is enabled. However the driver is required for
the built-in wireless MACs of the Atheros AR9130/AR9132
SoCs. These SoCs have no PCI controller, the wireless
MAC is connected to the AHB bus on them.
Introduce separated config options for the supported
buses, in order to allow building of ath9h without PCI
bus support.
As a bonus, this patch removes the cross-reference of
the ATHEROS_AR71XX option which is not present in the
kernel.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k can use minstrel_ht instead, so it makes sense to save some space here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move out the generic hardware family code out into their own
files, we have one for AR5008, AR9001, and AR9002 family (ar9002_hw.c)
and another file for the new AR9003 hardware family (ar9003_hw.c).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration code touches phy registers and since these
change the calibration code needs to be abstracted.
Noise floor calibration is the only thing remaining but
since the remaining calls only touch the AR_PHY_AGC_CONTROL
register we'll just define that register conditionally, that
will be done separately. The goal is to remove the dependency
of ar9002_phy.h on calib.c
This also adds stubs to be filled for AR9003 calibration code.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This add stubs for PHY support for the AR9003 hardware family.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PHY split is easier done in a few steps. First move
the RF ops to the private ops and rename them accordingly.
We split PHY stuff up first for the AR5008 and AR9002
families. There are some callbacks that AR9002 share
with the AR5008 familiy so we set those first, if AR9002
has some different callbacks it will override them upon
hardware init.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move initialization/de-initialization related
code to this file.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all LED/RFKILL/BTCOEX related code
to gpio.c
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In my setups, ath9k's debugfs files are most of the time much more
useful than the messages generated by enabling CONFIG_ATH_DEBUG along
with the right debug flags.
Since CONFIG_ATH_DEBUG comes with a noticeable overhead on embedded
systems, this patch makes it possible to use the debugfs files without
that option.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k and ath9k_htc share a lot of common hardware characteristics.
They only differ in that ath9k_htc works with a target CPU and ath9k
works directly with the hardware. ath9k_htc will do *some* things in
the firmware, but a lot of others on the host.
The common 802.11n hardware code is already shared through the ath9k_hw
module. Common helpers amongst all Atheros drivers can use the ath module,
this includes ath5k and ar9170 as users. But there is some common driver
specific helpers which are not exactly hardware code which ath9k and
ath9k_htc can share. We'll be using ath9k_common for this to avoid
bloating the ath module and the common 802.11n hardware module ath9k_hw.
We start by sharing skb pre and post processing in preparation for a hand
off to mac80211.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hw code for Atheros 802.11n hardware is commmon between
different chipsets. This moves this code into a separate
module, the next expected user of this code will be
the ath9k_htc module.
The ath9k/ dir is now selected by ATH9K_HW, an option which
gets selected by either ath9k or ath9k_htc, but remains
invisible for user menuconfig configuration. If either
ath9k or ath9k_htc will be compiled into the kernel
ath9k_hw will also be compiled in.
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the last part to make ath9k hw code core driver agnostic.
I believe ath9k_htc can now use use the hw code unmodified.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac.c is now core driver independent.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hw code will be shared between ath9k and ath9k_htc.
Just a few more files are left to clean up, mark them as well.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add eeprom_def.c, eeprom_4k.c and eeprom_9287.c
This improves maintainability.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
