The debug save/restore functions can be improved by using the has_vhe()
static key instead of the instruction alternative. Using the static key
uses the same paradigm as we're going to use elsewhere, it makes the
code more readable, and it generates slightly better code (no
stack setups and function calls unless necessary).
We also use a static key on the restore path, because it will be
marginally faster than loading a value from memory.
Finally, we don't have to conditionally clear the debug dirty flag if
it's set, we can just clear it.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no need to figure out inside the world-switch if we should
save/restore the debug registers or not, we might as well do that in the
higher level debug setup code, making it easier to optimize down the
line.
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We have numerous checks around that checks if the HCR_EL2 has the RW bit
set to figure out if we're running an AArch64 or AArch32 VM. In some
cases, directly checking the RW bit (given its unintuitive name), is a
bit confusing, and that's not going to improve as we move logic around
for the following patches that optimize KVM on AArch64 hosts with VHE.
Therefore, introduce a helper, vcpu_el1_is_32bit, and replace existing
direct checks of HCR_EL2.RW with the helper.
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we are about to move a bunch of save/restore logic for VHE kernels to
the load and put functions, we need some infrastructure to do this.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We currently have a separate read-modify-write of the HCR_EL2 on entry
to the guest for the sole purpose of setting the VF and VI bits, if set.
Since this is most rarely the case (only when using userspace IRQ chip
and interrupts are in flight), let's get rid of this operation and
instead modify the bits in the vcpu->arch.hcr[_el2] directly when
needed.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We always set the IMO and FMO bits in the HCR_EL2 when running the
guest, regardless if we use the vgic or not. By moving these flags to
HCR_GUEST_FLAGS we can avoid one of the extra save/restore operations of
HCR_EL2 in the world switch code, and we can also soon get rid of the
other one.
This is safe, because even though the IMO and FMO bits control both
taking the interrupts to EL2 and remapping ICC_*_EL1 to ICV_*_EL1 when
executed at EL1, as long as we ensure that these bits are clear when
running the EL1 host, we're OK, because we reset the HCR_EL2 to only
have the HCR_RW bit set when returning to EL1 on non-VHE systems.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shih-Wei Li <shihwei@cs.columbia.edu>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
VHE actually doesn't rely on clearing the VTTBR when returning to the
host kernel, and that is the current key mechanism of hyp_panic to
figure out how to attempt to return to a state good enough to print a
panic statement.
Therefore, we split the hyp_panic function into two functions, a VHE and
a non-VHE, keeping the non-VHE version intact, but changing the VHE
behavior.
The vttbr_el2 check on VHE doesn't really make that much sense, because
the only situation where we can get here on VHE is when the hypervisor
assembly code actually called into hyp_panic, which only happens when
VBAR_EL2 has been set to the KVM exception vectors. On VHE, we can
always safely disable the traps and restore the host registers at this
point, so we simply do that unconditionally and call into the panic
function directly.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We already have the percpu area for the host cpu state, which points to
the VCPU, so there's no need to store the VCPU pointer on the stack on
every context switch. We can be a little more clever and just use
tpidr_el2 for the percpu offset and load the VCPU pointer from the host
context.
This has the benefit of being able to retrieve the host context even
when our stack is corrupted, and it has a potential performance benefit
because we trade a store plus a load for an mrs and a load on a round
trip to the guest.
This does require us to calculate the percpu offset without including
the offset from the kernel mapping of the percpu array to the linear
mapping of the array (which is what we store in tpidr_el1), because a
PC-relative generated address in EL2 is already giving us the hyp alias
of the linear mapping of a kernel address. We do this in
__cpu_init_hyp_mode() by using kvm_ksym_ref().
The code that accesses ESR_EL2 was previously using an alternative to
use the _EL1 accessor on VHE systems, but this was actually unnecessary
as the _EL1 accessor aliases the ESR_EL2 register on VHE, and the _EL2
accessor does the same thing on both systems.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Calling vcpu_load() registers preempt notifiers for this vcpu and calls
kvm_arch_vcpu_load(). The latter will soon be doing a lot of heavy
lifting on arm/arm64 and will try to do things such as enabling the
virtual timer and setting us up to handle interrupts from the timer
hardware.
Loading state onto hardware registers and enabling hardware to signal
interrupts can be problematic when we're not actually about to run the
VCPU, because it makes it difficult to establish the right context when
handling interrupts from the timer, and it makes the register access
code difficult to reason about.
Luckily, now when we call vcpu_load in each ioctl implementation, we can
simply remove the call from the non-KVM_RUN vcpu ioctls, and our
kvm_arch_vcpu_load() is only used for loading vcpu content to the
physical CPU when we're actually going to run the vcpu.
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tweak the SHA256 update routines to invoke the SHA256 block transform
block by block, to avoid excessive scheduling delays caused by the
NEON algorithm running with preemption disabled.
Also, remove a stale comment which no longer applies now that kernel
mode NEON is actually disallowed in some contexts.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CBC MAC is strictly sequential, and so the current AES code simply
processes the input one block at a time. However, we are about to add
yield support, which adds a bit of overhead, and which we prefer to
align with other modes in terms of granularity (i.e., it is better to
have all routines yield every 64 bytes and not have an exception for
CBC MAC which yields every 16 bytes)
So unroll the loop by 4. We still cannot perform the AES algorithm in
parallel, but we can at least merge the loads and stores.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CBC encryption is strictly sequential, and so the current AES code
simply processes the input one block at a time. However, we are
about to add yield support, which adds a bit of overhead, and which
we prefer to align with other modes in terms of granularity (i.e.,
it is better to have all routines yield every 64 bytes and not have
an exception for CBC encrypt which yields every 16 bytes)
So unroll the loop by 4. We still cannot perform the AES algorithm in
parallel, but we can at least merge the loads and stores.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The AES block mode implementation using Crypto Extensions or plain NEON
was written before real hardware existed, and so its interleave factor
was made build time configurable (as well as an option to instantiate
all interleaved sequences inline rather than as subroutines)
We ended up using INTERLEAVE=4 with inlining disabled for both flavors
of the core AES routines, so let's stick with that, and remove the option
to configure this at build time. This makes the code easier to modify,
which is nice now that we're adding yield support.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When kernel mode NEON was first introduced on arm64, the preserve and
restore of the userland NEON state was completely unoptimized, and
involved saving all registers on each call to kernel_neon_begin(),
and restoring them on each call to kernel_neon_end(). For this reason,
the NEON crypto code that was introduced at the time keeps the NEON
enabled throughout the execution of the crypto API methods, which may
include calls back into the crypto API that could result in memory
allocation or other actions that we should avoid when running with
preemption disabled.
Since then, we have optimized the kernel mode NEON handling, which now
restores lazily (upon return to userland), and so the preserve action
is only costly the first time it is called after entering the kernel.
So let's put the kernel_neon_begin() and kernel_neon_end() calls around
the actual invocations of the NEON crypto code, and run the remainder of
the code with kernel mode NEON disabled (and preemption enabled)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When kernel mode NEON was first introduced on arm64, the preserve and
restore of the userland NEON state was completely unoptimized, and
involved saving all registers on each call to kernel_neon_begin(),
and restoring them on each call to kernel_neon_end(). For this reason,
the NEON crypto code that was introduced at the time keeps the NEON
enabled throughout the execution of the crypto API methods, which may
include calls back into the crypto API that could result in memory
allocation or other actions that we should avoid when running with
preemption disabled.
Since then, we have optimized the kernel mode NEON handling, which now
restores lazily (upon return to userland), and so the preserve action
is only costly the first time it is called after entering the kernel.
So let's put the kernel_neon_begin() and kernel_neon_end() calls around
the actual invocations of the NEON crypto code, and run the remainder of
the code with kernel mode NEON disabled (and preemption enabled)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When kernel mode NEON was first introduced on arm64, the preserve and
restore of the userland NEON state was completely unoptimized, and
involved saving all registers on each call to kernel_neon_begin(),
and restoring them on each call to kernel_neon_end(). For this reason,
the NEON crypto code that was introduced at the time keeps the NEON
enabled throughout the execution of the crypto API methods, which may
include calls back into the crypto API that could result in memory
allocation or other actions that we should avoid when running with
preemption disabled.
Since then, we have optimized the kernel mode NEON handling, which now
restores lazily (upon return to userland), and so the preserve action
is only costly the first time it is called after entering the kernel.
So let's put the kernel_neon_begin() and kernel_neon_end() calls around
the actual invocations of the NEON crypto code, and run the remainder of
the code with kernel mode NEON disabled (and preemption enabled)
Note that this requires some reshuffling of the registers in the asm
code, because the XTS routines can no longer rely on the registers to
retain their contents between invocations.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When kernel mode NEON was first introduced on arm64, the preserve and
restore of the userland NEON state was completely unoptimized, and
involved saving all registers on each call to kernel_neon_begin(),
and restoring them on each call to kernel_neon_end(). For this reason,
the NEON crypto code that was introduced at the time keeps the NEON
enabled throughout the execution of the crypto API methods, which may
include calls back into the crypto API that could result in memory
allocation or other actions that we should avoid when running with
preemption disabled.
Since then, we have optimized the kernel mode NEON handling, which now
restores lazily (upon return to userland), and so the preserve action
is only costly the first time it is called after entering the kernel.
So let's put the kernel_neon_begin() and kernel_neon_end() calls around
the actual invocations of the NEON crypto code, and run the remainder of
the code with kernel mode NEON disabled (and preemption enabled)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a NEON-accelerated implementation of Speck128-XTS and Speck64-XTS
for ARM64. This is ported from the 32-bit version. It may be useful on
devices with 64-bit ARM CPUs that don't have the Cryptography
Extensions, so cannot do AES efficiently -- e.g. the Cortex-A53
processor on the Raspberry Pi 3.
It generally works the same way as the 32-bit version, but there are
some slight differences due to the different instructions, registers,
and syntax available in ARM64 vs. in ARM32. For example, in the 64-bit
version there are enough registers to hold the XTS tweaks for each
128-byte chunk, so they don't need to be saved on the stack.
Benchmarks on a Raspberry Pi 3 running a 64-bit kernel:
Algorithm Encryption Decryption
--------- ---------- ----------
Speck64/128-XTS (NEON) 92.2 MB/s 92.2 MB/s
Speck128/256-XTS (NEON) 75.0 MB/s 75.0 MB/s
Speck128/256-XTS (generic) 47.4 MB/s 35.6 MB/s
AES-128-XTS (NEON bit-sliced) 33.4 MB/s 29.6 MB/s
AES-256-XTS (NEON bit-sliced) 24.6 MB/s 21.7 MB/s
The code performs well on higher-end ARM64 processors as well, though
such processors tend to have the Crypto Extensions which make AES
preferred. For example, here are the same benchmarks run on a HiKey960
(with CPU affinity set for the A73 cores), with the Crypto Extensions
implementation of AES-256-XTS added:
Algorithm Encryption Decryption
--------- ----------- -----------
AES-256-XTS (Crypto Extensions) 1273.3 MB/s 1274.7 MB/s
Speck64/128-XTS (NEON) 359.8 MB/s 348.0 MB/s
Speck128/256-XTS (NEON) 292.5 MB/s 286.1 MB/s
Speck128/256-XTS (generic) 186.3 MB/s 181.8 MB/s
AES-128-XTS (NEON bit-sliced) 142.0 MB/s 124.3 MB/s
AES-256-XTS (NEON bit-sliced) 104.7 MB/s 91.1 MB/s
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull "Freescale arm64 device tree updates for 4.17" from Shawn Guo:
- Move cpu_thermal device out of bus node to fix DTC simple_bus_reg
warning seen with W=1 switch.
- Fix IFC child nodes' unit-address to eliminate DTC simple_bus_reg
warnings.
- Add a dummy size memory 'reg' property for LS1046A device tree to
avoid unit_address_vs_reg DTC warning, and the real size will be
filled by bootloader.
- Update ls208xa-qds board device tree to fix unit_address_vs_reg
warnings with DSPI device.
- Add idle-states for LS1012A and LS1043A, and correct
arm,psci-suspend-param setting for already added idle-states.
- DPAA QBMan portal and watchdog device addition.
* tag 'imx-dt64-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: ifc: Fix the unit address format in the examples
arm64: dts: ls1046a: add a dummy memory 'reg' property
arm64: dts: fsl: fix ifc simple-bus unit address format warnings
arm64: dts: fsl: update the cpu idle node
arm64: dts: ls1043a: add cpu idle support
arm64: dts: ls1012a: add cpu idle support
arm64: dts: ls208xa-qds: Fix the 'reg' property
arm64: dts: ls208xa-qds: Pass unit name to dspi child nodes
arm64: dts: ls208xa: Move cpu_thermal out of bus node
arm64: dts: ls1088a: Move cpu_thermal out of bus node
arm64: dts: ls1046a: Move cpu_thermal out of bus node
arm64: dts: ls1043a: Move cpu_thermal out of bus node
arm64: dts: ls1012a: Move cpu_thermal out of bus node
arm64: dts: Add DPAA QBMan portal 9
arm64: dts: ls1088a: add DT node of watchdog
- Peace of mind locking fix in vgic_mmio_read_pending
- Allow hw-mapped interrupts to be reset when the VM resets
- Fix GICv2 multi-source SGI injection
- Fix MMIO synchronization for GICv2 on v3 emulation
- Remove excess verbosity on the console
-----BEGIN PGP SIGNATURE-----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=iyYE
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-fixes-for-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
kvm/arm fixes for 4.16, take 2
- Peace of mind locking fix in vgic_mmio_read_pending
- Allow hw-mapped interrupts to be reset when the VM resets
- Fix GICv2 multi-source SGI injection
- Fix MMIO synchronization for GICv2 on v3 emulation
- Remove excess verbosity on the console
According to Documentation/process/license-rules.rst, move the SPDX
License Identifier to the very top of the file. I used C++ comment
style not only for the SPDX line but for the entire block because
this seems Linus' preference [1]. I also dropped the parentheses to
follow the examples in that document.
[1] https://lkml.org/lkml/2017/11/25/133
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds regulators that have fixed voltage for audio codec
on UniPhier LD11/20 Global boards. This patch fixes warnings about
TAS57xx audio codec such as "tas571x 0-001b: 0-001b supply AVDD
not found, using dummy regulator".
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add nodes of the AVE ethernet controller for LD11 and LD20 SoCs
and the boards.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds compress audio node for S/PDIF on UniPhier LD11/20
global boards. And adds settings of AIO for it.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds codec node for TI TAS571x on UniPhier LD11/20
global boards. And adds settings of AIO for speaker out.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since 'num-slots' had already deprecated, remove the property in
device-tree file.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Calling vcpu_load() registers preempt notifiers for this vcpu and calls
kvm_arch_vcpu_load(). The latter will soon be doing a lot of heavy
lifting on arm/arm64 and will try to do things such as enabling the
virtual timer and setting us up to handle interrupts from the timer
hardware.
Loading state onto hardware registers and enabling hardware to signal
interrupts can be problematic when we're not actually about to run the
VCPU, because it makes it difficult to establish the right context when
handling interrupts from the timer, and it makes the register access
code difficult to reason about.
Luckily, now when we call vcpu_load in each ioctl implementation, we can
simply remove the call from the non-KVM_RUN vcpu ioctls, and our
kvm_arch_vcpu_load() is only used for loading vcpu content to the
physical CPU when we're actually going to run the vcpu.
Cc: stable@vger.kernel.org
Fixes: 9b062471e5 ("KVM: Move vcpu_load to arch-specific kvm_arch_vcpu_ioctl")
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Enable AHCI on Jetson TX1 and add sata phy node.
Signed-off-by: Preetham Chandru R <pchandru@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the (previously omitted) SCIF0 pin data to the V3M Starter Kit board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Display and graphics can't work together without an SMMU, so it is
effectively always getting enabled anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
On R-Car H3, on-chip peripheral modules that can make use of DMA are
wired to either SYS-DMAC0 only, or to both SYS-DMAC1 and SYS-DMAC2.
Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
SCIF[0125], and I2C[0-2]. These were initially left out because early
firmware versions prohibited using SYS-DMAC2. This restriction has been
lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25, 2016).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add r8a7795 IPMMU-PV1 and keep it disabled by default.
This device is not present in r8a7795 ES1.x and
is removed from the DT of those SoCs.
This corrects an omission in
3b7e7848f0 ("arm64: dts: renesas: r8a7795: Add IPMMU device nodes")
This does not have any runtime effect.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Sort root sub-nodes alphabetically for allow for easier maintenance of
this file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Eagle board dependent part of the I2C0 device node.
The I2C0 bus is populated by ON Semiconductor PCA9653 I/O expander and
Analog Devices ADV7511W HDMI transmitter (but we're only describing the
former chip now).
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 parts of the I2C[0-4] device node.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-XS boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the V3MSK board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii"
mode and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Eagle board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Draak board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77995 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the ULCB board provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96 SoC DTSI to use "rgmii" mode\
and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Salvator-X[S] board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96/965 SoC DTSI to use "rgmii"
mode and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Populate the device node for the Interrupt Controller for External
Devices (INTC-EX) on R-Car M3-N, which serves external IRQ pins
IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Populate the device node for the IIC Bus Interface for DVFS (IIC for
DVFS) on R-Car M3-N, and add an alias to fix its bus number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car M3-N SiP.
Most features are enabled through the shared salvator-xs.dtsi board
description. The memory configuration is specific to the M3-N SiP.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Switch to SPDX-License-Identifier, update patch description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#interrupt-cells" property and "interrupt-controller" label to
"interrupt-controller@e61c0000" device node.
This silences the following DTC compiler warnings:
Warning (interrupts_property): Missing interrupt-controller or
interrupt-map property in /soc/interrupt-controller@e61c0000
Warning (interrupts_property): Missing #interrupt-cells in
interrupt-parent /soc/interrupt-controller@e61c000
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#pwm-cells" property to "pwm@e6e31000" device node.
This silences the following DTC compiler warning:
Warning (pwms_property): Missing property '#pwm-cells' in node
/soc/pwm@e6e31000 or bad phandle (referred from /backlight:pwms[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#phy-cells" property to "usb-phy@e65ee000" device node.
This silences the following DTC compiler warning:
Warning (phys_property): Missing property '#phy-cells' in node
/soc/usb-phy@e65ee000 or bad phandle (referred from
/soc/usb@ee020000:phys[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove "reg" property from cache-controller-0 device node as it does not
have any unit address.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /cpus/cache-controller-0 has a reg
or ranges property, but no unit name
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#address-cells" and "#size-cells" properties to all place-holder nodes
that have children nodes defined by salvator-x[s].dtsi device tree.
This silences the following DTC compiler warnings:
Warning (reg_format): "reg" property in /soc/.. has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells
value for /soc/...
Warning (avoid_default_addr_size): Relying on default #size-cells value
for /soc/...
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "reg" properties to place-holder nodes with unit address defined for
R-Car M3-N SoC.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /soc/... has a unit name,
but no reg property
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add basic support for R-Car Salvator-X M3-N (R8A77965) board.
Based on original work from:
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the Gen 3 R-Car M3-N SoC.
Based on original work from:
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe frequencies, other than the default for CA53 cores. This is a
pre-requisite for using providing alternative frequencies for use with
CPUFreq with these cores.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe frequencies, other than the default for CA53 cores. This is a
pre-requisite for using providing alternative frequencies for use with
CPUFreq with these cores.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
sdhci for rk3399-sapphire works for eMMC but keep-power-in-suspend
is an optional property for SDIO.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
pinctrl hogs on rk3399-gru-kevin that broke suspend. This gets fixed
by moving the wifi pinctrl to the correct node.
Also revert the usb3 phy-port enablement, as a missing feature in the
type-c phy breaks usb on all non-gru rk3399 boards.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlqj23sQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgf9kB/9/dpdz7OVY4u2WPhr7AHZjv+dBl9dt0uI6
1ttbWzH2sXQcfUivy89hAEQYBB3hR5GsZZIIWA9ProsiHpnH6hHQTwRmy/H+2QBI
hg1XyYAh7eiQoOjvMUT6at2SfCRofPbSoLBVo3JBlwlbSCBEy+WpQZjLXWdD+Bqy
Cj1H6PWlCV8p0W7T1YsMfltOM7Kh55tew+1+XTpkEJ2PHgz+Ht1mh4h59nEvG+s/
BdJ2hos9UW/O7OPdpa6pQUGf8/tZRSacmAXL8Z6W+kUzzsDTnYFN2S8cuJ7CeZCY
0+azrYptuSvs+1xAe221axu0GlVPltSC3eylI4pWECpFfh3f/ARK
=iow6
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rockchip-dts64fixes-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts64 fixes for 4.16" from Heiko Stübner:
Pinctrl got a fix in 4.16-rc1, that exposed an issue with wifi-related
pinctrl hogs on rk3399-gru-kevin that broke suspend. This gets fixed
by moving the wifi pinctrl to the correct node.
Also revert the usb3 phy-port enablement, as a missing feature in the
type-c phy breaks usb on all non-gru rk3399 boards.
* tag 'v4.16-rockchip-dts64fixes-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
Revert "arm64: dts: rockchip: add usb3-phy otg-port support for rk3399"
arm64: dts: rockchip: Fix rk3399-gru-* s2r (pinctrl hogs, wifi reset)
- Enable deadline IO scheduler to improve the performnace for some
usecaese without changing the default IO scheduler
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BscW
-----END PGP SIGNATURE-----
Merge tag 'hisi-defconfig-for-4.17' of git://github.com/hisilicon/linux-hisi into next/soc
Pull "ARM64: hisilicon: defconfig updates for 4.17" from Wei Xu:
- Enable deadline IO scheduler to improve the performnace for some
usecaese without changing the default IO scheduler
* tag 'hisi-defconfig-for-4.17' of git://github.com/hisilicon/linux-hisi:
arm64: defconfig: enable IOSCHED_DEADLINE
- convert to the SPDX-License-Identifier
- add missing clocks (for the registers) on some of the peripherals
- use the new nand driver
- add more uart for Armada 7K/8K SoCs
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWqLBBgAKCRALBhiOFHI7
1dQ0AKCOUzXMHkC5/f0hwgPYpmzKuQGZjACfQA6eVistsl3QfTN0Nph57jRW9IE=
=KBPW
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.17-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt64 for 4.17 (part 1)" from Gregory CLEMENT:
- convert to the SPDX-License-Identifier
- add missing clocks (for the registers) on some of the peripherals
- use the new nand driver
- add more uart for Armada 7K/8K SoCs
* tag 'mvebu-dt64-4.17-1' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada-cp110: Add apb_pclk clock for the uart nodes
arm64: dts: marvell: use reworked NAND controller driver on Armada 8K
arm64: dts: marvell: use reworked NAND controller driver on Armada 7K
ARM64: dts: marvell: armada-cp110: Add registers clock for sata node
arm64: dts: marvell: armada-8080-db: use SPDX-License-Identifier
arm64: dts: marvell: armada-8040-mcbin: use SPDX-License-Identifier
arm64: dts: marvell: armada-8040-db: use SPDX-License-Identifier
arm64: dts: marvell: armada-7040-db: use SPDX-License-Identifier
arm64: dts: marvell: armada-3720-espressobin: use SPDX-License-Identifier
arm64: dts: marvell: armada-3720-db: use SPDX-License-Identifier
arm64: dts: marvell: use SPDX-License-Identifier for Armada SoCs
arm64: dts: marvell: mcbin: fix board name typo
arm64: dts: marvell: mcbin: enable uart headers
arm64: dts: marvell: add CP110 uart peripherals
ARM64: dts: marvell: armada-cp110: Add registers clock for I2C nodes
ARM64: dts: marvell: armada-cp110: Add registers clock for SPI nodes
- Add XGE CPLD control support for hip07 SoC
- Disable the SMMU on hip06 and hip07 SoCs becuase of
the hardware limitation
- Enable HS200 mode for the MMC controller on hi6220 hikey board
- Remove "cooling-{min|max}-level" this kind unused properties
for hi6220 SoC
- Add watchdog node for hi6220 SoC
- Remove "CPU_NAP" idle state on hikey960 board since it is
not stable and useless with the updated firmware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HIMw
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm64-dt-for-4.17' of git://github.com/hisilicon/linux-hisi into next/dt
Pull "ARM64: DT: Hisilicon SoC DT updates for 4.17" from Wei Xu:
- Add XGE CPLD control support for hip07 SoC
- Disable the SMMU on hip06 and hip07 SoCs becuase of
the hardware limitation
- Enable HS200 mode for the MMC controller on hi6220 hikey board
- Remove "cooling-{min|max}-level" this kind unused properties
for hi6220 SoC
- Add watchdog node for hi6220 SoC
- Remove "CPU_NAP" idle state on hikey960 board since it is
not stable and useless with the updated firmware
* tag 'hisi-arm64-dt-for-4.17' of git://github.com/hisilicon/linux-hisi:
arm64: dts: Hi3660: Remove 'CPU_NAP' idle state
arm64: dts: hi6220: enable watchdog
ARM64: dts: hi6220: Remove "cooling-{min|max}-level" for CPU nodes
arm64: dts: hikey: Enable HS200 mode on eMMC
arm64: dts: hisi: Disable hisilicon smmu node on hip06/hip07
arm64: dts: hisi: add hns-dsaf cpld control for the hip07 SoC
The ACLK_VIO is a parent clock used by a several children,
its suggested clock rate is 400MHz. Right now it gets 400MHz
because it sources from CPLL(800M) and divides by 2 after reset.
It's good not to rely on default values like this, so let's
explicitly set it.
NOTE: it's expected that at least one board may override cru node and
set the CPLL to 1.6 GHz. On that board it will be very important to be
explicit about aclk-vio being 400 MHz.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
add mmc device nodes and proper setup for used pins
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jimin Wang <jimin.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds SATA support fot MT7622.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds PCIe support for MT7622.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
[mb: fix type in commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add ethernet device nodes which enable GMAC1 with SGMII interface
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add nodes for NOR flash, parallel Nand flash with error correction code
support.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: RogerCC Lin <rogercc.lin@mediatek.com>
Cc: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch also cleans up two oscillators that provide clocks for MT7623.
Switch the uart clocks to the real ones while at it.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clocks, regulators and opp information into cpu nodes.
In addition, the power supply for cpu nodes is deployed on
mt7622-rfb1 board.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable pwrap and MT6380 on mt7622-rfb1 board. Also add all mt6380
regulator nodes in an alone file to allow similar boards using MT6380
able to resue the configuration.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
[mb: add missing space]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add pinctrl device nodes and rfb1 board, additionally include all pin
groups possible being used on rfb1 board and available gpio keys.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clock controller nodes for MT7622 and include header for topckgen,
infracfg, pericfg, apmixedsys, ethsys, sgmiisys, pciesys and ssusbsys
for those devices nodes to be added afterwards.
In addition, provides an oscillator node for the source of PLLs and dummy
clock for PWARP to complement missing support of clock gate for the
wrapper circuit in the driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- The SMCCC firmware interface for the spectre variant 2 mitigation has
been updated to allow the discovery of whether the CPU needs the
workaround. This pull request relaxes the kernel check on the return
value from firmware.
- Fix the commit allowing changing from global to non-global page table
entries which inadvertently disallowed other safe attribute changes.
- Fix sleeping in atomic during the arm_perf_teardown_cpu() code.
-----BEGIN PGP SIGNATURE-----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=jVvu
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- The SMCCC firmware interface for the spectre variant 2 mitigation has
been updated to allow the discovery of whether the CPU needs the
workaround. This pull request relaxes the kernel check on the return
value from firmware.
- Fix the commit allowing changing from global to non-global page table
entries which inadvertently disallowed other safe attribute changes.
- Fix sleeping in atomic during the arm_perf_teardown_cpu() code.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Relax ARM_SMCCC_ARCH_WORKAROUND_1 discovery
arm_pmu: Use disable_irq_nosync when disabling SPI in CPU teardown hook
arm64: mm: fix thinko in non-global page table attribute check
A recent update to the ARM SMCCC ARCH_WORKAROUND_1 specification
allows firmware to return a non zero, positive value to describe
that although the mitigation is implemented at the higher exception
level, the CPU on which the call is made is not affected.
Let's relax the check on the return value from ARCH_WORKAROUND_1
so that we only error out if the returned value is negative.
Fixes: b092201e00 ("arm64: Add ARM_SMCCC_ARCH_WORKAROUND_1 BP hardening support")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This extra clock is needed to access the registers of the UARTs used on
CP110 component of the Armada 7K/8K SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Currently, as reported by Eric, an invalid si_code value 0 is
passed in many signals delivered to userspace in response to faults
and other kernel errors. Typically 0 is passed when the fault is
insufficiently diagnosable or when there does not appear to be any
sensible alternative value to choose.
This appears to violate POSIX, and is intuitively wrong for at
least two reasons arising from the fact that 0 == SI_USER:
1) si_code is a union selector, and SI_USER (and si_code <= 0 in
general) implies the existence of a different set of fields
(siginfo._kill) from that which exists for a fault signal
(siginfo._sigfault). However, the code raising the signal
typically writes only the _sigfault fields, and the _kill
fields make no sense in this case.
Thus when userspace sees si_code == 0 (SI_USER) it may
legitimately inspect fields in the inactive union member _kill
and obtain garbage as a result.
There appears to be software in the wild relying on this,
albeit generally only for printing diagnostic messages.
2) Software that wants to be robust against spurious signals may
discard signals where si_code == SI_USER (or <= 0), or may
filter such signals based on the si_uid and si_pid fields of
siginfo._sigkill. In the case of fault signals, this means
that important (and usually fatal) error conditions may be
silently ignored.
In practice, many of the faults for which arm64 passes si_code == 0
are undiagnosable conditions such as exceptions with syndrome
values in ESR_ELx to which the architecture does not yet assign any
meaning, or conditions indicative of a bug or error in the kernel
or system and thus that are unrecoverable and should never occur in
normal operation.
The approach taken in this patch is to translate all such
undiagnosable or "impossible" synchronous fault conditions to
SIGKILL, since these are at least probably localisable to a single
process. Some of these conditions should really result in a kernel
panic, but due to the lack of diagnostic information it is
difficult to be certain: this patch does not add any calls to
panic(), but this could change later if justified.
Although si_code will not reach userspace in the case of SIGKILL,
it is still desirable to pass a nonzero value so that the common
siginfo handling code can detect incorrect use of si_code == 0
without false positives. In this case the si_code dependent
siginfo fields will not be correctly initialised, but since they
are not passed to userspace I deem this not to matter.
A few faults can reasonably occur in realistic userspace scenarios,
and _should_ raise a regular, handleable (but perhaps not
ignorable/blockable) signal: for these, this patch attempts to
choose a suitable standard si_code value for the raised signal in
each case instead of 0.
arm64 was the only arch to define a BUS_FIXME code, so after this
patch nobody defines it. This patch therefore also removes the
relevant code from siginfo_layout().
Cc: James Morse <james.morse@arm.com>
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The DCache clean & ICache invalidation requirements for instructions
to be data coherence are discoverable through new fields in CTR_EL0.
The following two control bits DIC and IDC were defined for this
purpose. No need to perform point of unification cache maintenance
operations from software on systems where CPU caches are transparent.
This patch optimize the three functions __flush_cache_user_range(),
clean_dcache_area_pou() and invalidate_icache_range() if the hardware
reports CTR_EL0.IDC and/or CTR_EL0.IDC. Basically it skips the two
instructions 'DC CVAU' and 'IC IVAU', and the associated loop logic
in order to avoid the unnecessary overhead.
CTR_EL0.DIC: Instruction cache invalidation requirements for
instruction to data coherence. The meaning of this bit[29].
0: Instruction cache invalidation to the point of unification
is required for instruction to data coherence.
1: Instruction cache cleaning to the point of unification is
not required for instruction to data coherence.
CTR_EL0.IDC: Data cache clean requirements for instruction to data
coherence. The meaning of this bit[28].
0: Data cache clean to the point of unification is required for
instruction to data coherence, unless CLIDR_EL1.LoC == 0b000
or (CLIDR_EL1.LoUIS == 0b000 && CLIDR_EL1.LoUU == 0b000).
1: Data cache clean to the point of unification is not required
for instruction to data coherence.
Co-authored-by: Philip Elcan <pelcan@codeaurora.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Omit patching of ADRP instruction at module load time if the current
CPUs are not susceptible to the erratum.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: Drop duplicate initialisation of .def_scope field]
Signed-off-by: Will Deacon <will.deacon@arm.com>
In some cases, core variants that are affected by a certain erratum
also exist in versions that have the erratum fixed, and this fact is
recorded in a dedicated bit in system register REVIDR_EL1.
Since the architecture does not require that a certain bit retains
its meaning across different variants of the same model, each such
REVIDR bit is tightly coupled to a certain revision/variant value,
and so we need a list of revidr_mask/midr pairs to carry this
information.
So add the struct member and the associated macros and handling to
allow REVIDR fixes to be taken into account.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Working around Cortex-A53 erratum #843419 involves special handling of
ADRP instructions that end up in the last two instruction slots of a
4k page, or whose output register gets overwritten without having been
read. (Note that the latter instruction sequence is never emitted by
a properly functioning compiler, which is why it is disregarded by the
handling of the same erratum in the bfd.ld linker which we rely on for
the core kernel)
Normally, this gets taken care of by the linker, which can spot such
sequences at final link time, and insert a veneer if the ADRP ends up
at a vulnerable offset. However, linux kernel modules are partially
linked ELF objects, and so there is no 'final link time' other than the
runtime loading of the module, at which time all the static relocations
are resolved.
For this reason, we have implemented the #843419 workaround for modules
by avoiding ADRP instructions altogether, by using the large C model,
and by passing -mpc-relative-literal-loads to recent versions of GCC
that may emit adrp/ldr pairs to perform literal loads. However, this
workaround forces us to keep literal data mixed with the instructions
in the executable .text segment, and literal data may inadvertently
turn into an exploitable speculative gadget depending on the relative
offsets of arbitrary symbols.
So let's reimplement this workaround in a way that allows us to switch
back to the small C model, and to drop the -mpc-relative-literal-loads
GCC switch, by patching affected ADRP instructions at runtime:
- ADRP instructions that do not appear at 4k relative offset 0xff8 or
0xffc are ignored
- ADRP instructions that are within 1 MB of their target symbol are
converted into ADR instructions
- remaining ADRP instructions are redirected via a veneer that performs
the load using an unaffected movn/movk sequence.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: tidied up ADRP -> ADR instruction patching.]
[will: use ULL suffix for 64-bit immediate]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Enable Tegra BPMP thermal sensor support by default, built as a module.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable Tegra186 CPU frequency scaling support by default.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Whether or not we will ever decide to start using x18 as a platform
register in Linux is uncertain, but by that time, we will need to
ensure that UEFI runtime services calls don't corrupt it.
So let's start issuing warnings now for this, and increase the
likelihood that these firmware images have all been replaced by that time.
This has been fixed on the EDK2 side in commit:
6d73863b5464 ("BaseTools/tools_def AARCH64: mark register x18 as reserved")
dated July 13, 2017.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20180308080020.22828-6-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Enable the various CPUFREQ governors and statistics to ease development.
Don't change the default governor - performance governor.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable the driver for the TSENS IP that is present across several QCOM
SoCs.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The APCS block is present on several Qualcomm SoCs e.g. 8916, 8996. On the
8916 it is needed to enable the clock controller that in turn enables
cpufreq on the platform while on the 8996 it is needed for communication
with RPM.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Set correct clocks and interrupt values.
Fixes the incorrect SPI master configuration. This is
mandatory to make the SPI5 interface functional.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add cpu cooling maps for cpu passive trip points. The cpu cooling
device states are mapped to cpufreq based scaling frequencies.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
A 2MB shared memory region is used on MSM8996 for exchanging sector data
in rmtfs. Add this chunk of reserved memory now that we have the
rmtfs-mem compatible to describe it and its memory protection
properties.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add a CPU OPP table to allow CPU frequency scaling on msm8916 platforms.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
There are clock controller registers in the APCS block, which purpose
is to control the main CPU mux and divider. Add the clock properties as
part of the APCS device-tree node.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The APCS block was exposed until now as a syscon, but now we have a
proper driver for this block. Add the compatible string of the new
driver to probe and register the mailbox functionality.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add a device tree node for the A53 PLL, which exists on msm8916
platforms.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
GICv3 does not have affinity bitmap in the binding for PPI
interrupts. It can be specified using a 4th cell if needed
as documented in the bindings. Clean up the wrong use of the
affinity bitmap using the GIC_CPU_MASK_SIMPLE() macro
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable NVIDIA Tegra194 support in the default 64-bit ARM configuration.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We currently have to rely on the GCC large code model for KASLR for
two distinct but related reasons:
- if we enable full randomization, modules will be loaded very far away
from the core kernel, where they are out of range for ADRP instructions,
- even without full randomization, the fact that the 128 MB module region
is now no longer fully reserved for kernel modules means that there is
a very low likelihood that the normal bottom-up allocation of other
vmalloc regions may collide, and use up the range for other things.
Large model code is suboptimal, given that each symbol reference involves
a literal load that goes through the D-cache, reducing cache utilization.
But more importantly, literals are not instructions but part of .text
nonetheless, and hence mapped with executable permissions.
So let's get rid of our dependency on the large model for KASLR, by:
- reducing the full randomization range to 4 GB, thereby ensuring that
ADRP references between modules and the kernel are always in range,
- reduce the spillover range to 4 GB as well, so that we fallback to a
region that is still guaranteed to be in range
- move the randomization window of the core kernel to the middle of the
VMALLOC space
Note that KASAN always uses the module region outside of the vmalloc space,
so keep the kernel close to that if KASAN is enabled.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When PLTs are emitted at relocation time, we really should not exceed
the number that we counted when parsing the relocation tables, and so
currently, we BUG() on this condition. However, even though this is a
clear bug in this particular piece of code, we can easily recover by
failing to load the module.
So instead, return 0 from module_emit_plt_entry() if this condition
occurs, which is not a valid kernel address, and can hence serve as
a flag value that makes the relocation routine bail out.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add device tree files for the Tegra194 P2972-0000 development board.
The board consists of the P2888 compute module and the P2822 baseboard.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the chip-level device tree, including binding headers, for the
NVIDIA Tegra194 "Xavier" system-on-chip. Only a small subset of devices
are initially available, enough to boot to UART console.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Xilinx zc1751 boards is used for silicon validation. Board can be
extended with 5 FMCs/DCs cards to connect various IPs. Describe all
these combinations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
These 3 boards requires minimal support to get Linux up and running.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Xilinx zcu111 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Xilinx zcu106 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Xilinx zcu104 is another customer board. It is sort of zcu102 clone
with some differences.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This patch is adding revA, revB and rev1.0. There are also other
revisions between which should be backward compatible with previous
versions. Unfortunately all revs are still in use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This board has 2GB of memory, i2c, sd, wifi sdio, spis, uarts, display
port and usbs.
Board is using fixed clocks because clock driver hasn't been merged yet.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This patch add 8-bit bus width property to eMMC node.
Signed-off-by: P L Sai Krishna <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds the sata port phy OOB timing values in the sata
device-tree node.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds a specific wetek dtsi to handle the specific Hub and Play2
boards by no more depending on the p20x dtsi.
This simplifies the hub and play2 dts and will avoid breaking these
boards when adding p200 and p201 specific changes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Different modules maybe installed by the user on the eMMC connector
of the odroid-c2. While the red modules are working without an issue,
it seems some black modules (apparently Samsung based) are having
issue at 200MHz
While the tuning algorithm introduced in v4.14 enables high speed modes
on every other tested designs, it seems a problem remains for this
particular combination of board and eMMC module.
Lowering the maximum frequency of the eMMC on this board until we can
figure out a better solution.
Fixes: d341ca88ee ("mmc: meson-gx: rework tuning function")
Suggested-by: Ellie Reeves <ellierevves@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move the SPDX-License-Identifier lines to the top and drop the
license splat.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The compatible in pwm_AO_cd is wrong and does not match anything.
Correct this with the correct compatible string
Fixes: 4a81e5ddfb ("ARM64: dts: meson-axg: add PWM DT info for Meson-Axg SoC")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the secure AO system controller with chipid enabled
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
1. Add support for HDMI audio on Exynos 5433 TM2/TM2E boards.
2. Add support for USB-MHL connector on Exynos 5433 TM2/TM2E boards.
-----BEGIN PGP SIGNATURE-----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=p0sr
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DTS ARM64 changes for v4.17" from Krzysztof Kozłowski:
1. Add support for HDMI audio on Exynos 5433 TM2/TM2E boards.
2. Add support for USB-MHL connector on Exynos 5433 TM2/TM2E boards.
* tag 'samsung-dt64-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: add OF graph between MHL and USB connector
arm64: dts: exynos: add micro-USB connector node to TM2 platforms
ARM: dts: exynos: Add support for HDMI audio on Exynos 5433 TM2 board
ARM: dts: exynos: Update I2S0 device node in exynos5433
ARM: dts: exynos: Add I2S1 device node to exynos5433
'linux,stdout-path' has been deprecated for some time in favor of
'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'.
Search and replace the one occurrence with 'stdout-path'.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Spreadtrum SC9860 platform has one SC2731 PMIC, and the SC2731
PMIC integrates all mobile handset power management, audio codec,
battery management and user interface support function in a single
chip.
This patch adds the SC2731 dts file, as well as adding the RTC and
regulator device node for this PMIC.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Spreadtrum SC9860 platform has two DMA controllers, one is located
on the ap-ahb system, and another one is located on the agcp system.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the watchdog device node for Spreadtrum SC9860 platform to
watch the system's stability.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We will use one always-on timer to be the broadcast device, thus add
the timer device node for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds the pin controller device node for Spreadtrum
SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We will access the PMIC through ADI controller, thus this patch adds
the ADI device node for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Spreadtrum SC9860 platform only has one hardware spinlock device,
which is located on AON system of Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
TCR_EL1.NFD1 was allocated by SVE and ensures that fault-surpressing SVE
memory accesses (e.g. speculative accesses from a first-fault gather load)
which translate via TTBR1_EL1 result in a translation fault if they
miss in the TLB when executed from EL0. This mitigates some timing attacks
against KASLR, where the kernel address space could otherwise be probed
efficiently using the FFR in conjunction with suppressed faults on SVE
loads.
Cc: Dave Martin <Dave.Martin@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This is the equivalent of commit 001bf455d2 ("ARM: 8428/1: kgdb: Fix
registers on sleeping tasks") but for arm64. Nuff said.
...well, perhaps I could also add that task_pt_regs are userspace
registers and that's not what kgdb is supposed to be reporting. We're
supposed to be reporting kernel registers.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This is a follow up patch to the series I sent recently that cleans up
KASAN_SHADOW_SCALE_SHIFT usage (which value was hardcoded and scattered
all over the code). This fixes the one place that I forgot to fix.
The change is purely aesthetical, instead of hardcoding the value for
KASAN_SHADOW_SCALE_SHIFT in arch/arm64/Makefile, an appropriate variable
is declared and used.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 9730348075 ("arm64: Increase the max granular size") increased
the cache line size to 128 to match Cavium ThunderX, apparently for some
performance benefit which could not be confirmed. This change, however,
has an impact on the network packets allocation in certain
circumstances, requiring slightly over a 4K page with a significant
performance degradation.
This patch reverts L1_CACHE_SHIFT back to 6 (64-byte cache line) while
keeping ARCH_DMA_MINALIGN at 128. The cache_line_size() function was
changed to default to ARCH_DMA_MINALIGN in the absence of a meaningful
CTR_EL0.CWG bit field.
In addition, if a system with ARCH_DMA_MINALIGN < CTR_EL0.CWG is
detected, the kernel will force swiotlb bounce buffering for all
non-coherent devices since DMA cache maintenance on sub-CWG ranges is
not safe, leading to data corruption.
Cc: Tirumalesh Chalamarla <tchalamarla@cavium.com>
Cc: Timur Tabi <timur@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In cases where x30 is used as a temporary in the out-of-line ll/sc atomics
(e.g. atomic_fetch_add), the compiler tends to put out a full stackframe,
which included pointing the x29 at the new frame.
Since these things aren't traceable anyway, we can pass -fomit-frame-pointer
to reduce the work when spilling. Since this is incompatible with -pg, we
also remove that from the CFLAGS for this file.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Using arm64_force_sig_info means that printing messages about unhandled
signals is dealt with for us, so use that in preference to force_sig_info
and remove any homebrew printing code.
Signed-off-by: Will Deacon <will.deacon@arm.com>
show_unhandled_signals_ratelimited is only called in traps.c, so move it
out of its macro in the dreaded system_misc.h and into a static function
in traps.c
Signed-off-by: Will Deacon <will.deacon@arm.com>
If we fail to deliver a signal due to taking an unhandled fault on the
stackframe, we can call arm64_notify_segfault to deliver a SEGV can deal
with printing any unhandled signal messages for us, rather than roll our
own printing code.
A side-effect of this change is that we now deliver the frame address
in si_addr along with an si_code of SEGV_{ACC,MAP}ERR, rather than an
si_addr of 0 and an si_code of SI_KERNEL as before.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Reporting unhandled user pagefaults via arm64_force_sig_info means
that __do_user_fault can be drastically simplified, since it no longer
has to worry about printing the fault information and can consequently
just take the siginfo as a parameter.
Signed-off-by: Will Deacon <will.deacon@arm.com>
There's no need for callers of arm64_notify_die to print information
about user faults. Instead, they can pass a string to arm64_notify_die
which will be printed subject to show_unhandled_signals.
Signed-off-by: Will Deacon <will.deacon@arm.com>
arm64_notify_die deals with printing out information regarding unhandled
signals, so there's no need to roll our own code here.
Signed-off-by: Will Deacon <will.deacon@arm.com>
In preparation for consolidating our handling of printing unhandled
signals, introduce a wrapper around force_sig_info which can act as
the canonical place for dealing with show_unhandled_signals.
Initially, we just hook this up to arm64_notify_die.
Signed-off-by: Will Deacon <will.deacon@arm.com>
For signals other than SIGKILL or those with siginfo_layout(signal, code)
== SIL_FAULT then force_signal_inject does not initialise the siginfo_t
properly. Since the signal number is determined solely by the caller,
simply WARN on unknown signals and force to SIGKILL.
Reported-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
force_signal_inject is a little flakey:
* It only knows about SIGILL and SIGSEGV, so can potentially deliver
other signals based on a partially initialised siginfo_t
* It sets si_addr to point at the PC for SIGSEGV
* It always operates on current, so doesn't need the regs argument
This patch fixes these issues by always assigning the si_addr field to
the address parameter of the function and updates the callers (including
those that indirectly call via arm64_notify_segfault) accordingly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
OF graph describes MHL data lanes between MHL and respective USB
connector.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since USB connector bindings are available we can describe it on TM2(e).
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable support in arm64's defconfig for Socionext SynQuacer based
platforms, by enabling the arch Kconfig symbol, and enabling builtin
support for the ethernet, GPIO and SDHCI controllers
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
New crypto drivers have been introduced in v4.16 that implement the
SHA-512, SHA3 and SM3 secure hash algorithms using ARMv8.2 optional
instructions. Add these drivers to arm64's defconfig as modules.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
libfdt gained a new dependency on strrchr, so make it available to the
EFI namespace before we update libfdt.
Thanks to Ard for providing this fix.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The word "feature" is repeated in the CPU features reporting. This drops it
for improved readability.
Before (redundant "feature" word):
SMP: Total of 4 processors activated.
CPU features: detected feature: 32-bit EL0 Support
CPU features: detected feature: Kernel page table isolation (KPTI)
CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
CPU: All CPU(s) started at EL2
After:
SMP: Total of 4 processors activated.
CPU features: detected: 32-bit EL0 Support
CPU features: detected: Kernel page table isolation (KPTI)
CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
CPU: All CPU(s) started at EL2
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The PAN emulation notification was only happening for non-boot CPUs
if CPU capabilities had already been configured. This seems to be the
wrong place, as it's system-wide and isn't attached to capabilities,
so its reporting didn't normally happen. Instead, report it once from
the boot CPU.
Before (missing PAN emulation report):
SMP: Total of 4 processors activated.
CPU features: detected feature: 32-bit EL0 Support
CPU features: detected feature: Kernel page table isolation (KPTI)
CPU: All CPU(s) started at EL2
After:
SMP: Total of 4 processors activated.
CPU features: detected feature: 32-bit EL0 Support
CPU features: detected feature: Kernel page table isolation (KPTI)
CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
CPU: All CPU(s) started at EL2
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that the early kernel mapping logic can tolerate placements of
Image that cross swapper table boundaries, we can remove the logic
that adjusts the offset if the dice roll produced an offset that
puts the kernel right on top of one.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mirror arm behaviour for unimplemented syscalls: Below 2048 return
-ENOSYS, above 2048 raise SIGILL.
Signed-off-by: Michael Weiser <michael.weiser@gmx.de>
[will: Tweak die string to identify as compat syscall]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Thanks a lot for Vincent Guittot careful work to find bug for 'CPU_NAP'
idle state. At early time, the CPU CA73 CPU_NAP idle state has been
supported on Hikey960. Later we found the system has the hang issue
and for resolving this issue Hisilicon released new MCU firmware, but
unfortunately the new MCU firmware has side effect and results in the
CA73 CPU cannot really enter CPU_NAP state and roll back to WFI state.
After discussion we cannot see the possibility to enable CA73 CPU_NAP
state anymore on Hikey960, based on this conclusion we should remove
this state from DT binding.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Kevin Wang <jean.wangtao@linaro.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This patch is to add watchdog binding for Hi6220 on Hikey board.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Moreover, the entries are incorrect here as min level is 4 and the max
level is 0.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
According to the hi6220 datasheet, the MMC controller is JEDEC eMMC 4.5
compliant, in addition to supporting a clock of up to 150MHz. The Hikey
schematic also indicates the device utilizes 1.8v signaling. Define these
parameters in the device tree to enable HS200 mode.
Signed-off-by: Ryan Grachek <ryan@edited.us>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The HiSilicon erratum 161010801 describes the limitation of
HiSilicon platforms hip06/hip07 to support the SMMUv3 mappings
for MSI transactions.
PCIe controller on these platforms has to differentiate the
MSI payload against other DMA payload and has to modify the
MSI payload. This makes it difficult for these platforms to
have SMMU translation for MSI. In order to workaround this,
ARM SMMUv3 driver requires a quirk to treat the MSI regions
separately. Such a quirk is currently missing for DT based
systems and therefore we need to explicitly disable the
hip06/hip07 smmu entries in dts.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
For certain workloads the deadline IO scheduler offers
particular advantages over other schedulers and has shown
to perform better, so enable it.
The default IO scheduler is unaffected by this change, and
currently is CFQ.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add cpld-syscon node to support the cpld control for hns-dsaf
on the hip07 SoC.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Enable HDMI output on all boards with HDMI connector.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This reverts commit c301b327ae.
While this works splendidly on rk3399-gru devices using the cros-ec
extcon, other rk3399-based devices using the fusb302 or no power-delivery
controller at all don't probe at all anymore, as the typec-phy currently
always expects the extcon to be available and therefore defers probing
indefinitly on these.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Back in the early days when gru devices were still under development
we found an issue where the WiFi reset line needed to be configured as
early as possible during the boot process to avoid the WiFi module
being in a bad state.
We found that the way to get the kernel to do this in the earliest
possible place was to configure this line in the pinctrl hogs, so
that's what we did. For some history here you can see
<http://crosreview.com/368770>. After the time that change landed in
the kernel, we landed a firmware change to configure this line even
earlier. See <http://crosreview.com/399919>. However, even after the
firmware change landed we kept the kernel change to deal with the fact
that some people working on devices might take a little while to
update their firmware.
At this there are definitely zero devices out in the wild that have
firmware without the fix in it. Specifically looking in the firmware
branch several critically important fixes for memory stability landed
after the patch in coreboot and I know we didn't ship without those.
Thus, by now, everyone should have the new firmware and it's safe to
not have the kernel set this up in a pinctrl hog.
Historically, even though it wasn't needed to have this in a pinctrl
hog, we still kept it since it didn't hurt. Pinctrl would apply the
default hog at bootup and then would never touch things again. That
all changed with commit 981ed1bfbc ("pinctrl: Really force states
during suspend/resume"). After that commit then we'll re-apply the
default hog at resume time and that can screw up the reset state of
WiFi. ...and on rk3399 if you touch a device on PCIe in the wrong way
then the whole system can go haywire. That's what was happening.
Specifically you'd resume a rk3399-gru-* device and it would mostly
resume, then would crash with some crazy weird crash.
One could say, perhaps, that the recent pinctrl change was at fault
(and should be fixed) since it changed behavior. ...but that's not
really true. The device tree for rk3399-gru is really to blame.
Specifically since the pinctrl is defined in the hog and not in the
"wlan-pd-n" node then the actual user of this pin doesn't have a
pinctrl entry for it. That's bad.
Let's fix our problems by just moving the control of
"wlan_module_reset_l pinctrl" out of the hog and put them in the
proper place.
NOTE: in theory, I think it should actually be possible to have a pin
controlled _both_ by the hog and by an actual device. Once the device
claims the pin I think the hog is supposed to let go. I'm not 100%
sure that this works and in any case this solution would be more
complex than is necessary.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Fixes: 48f4d9796d ("arm64: dts: rockchip: add Gru/Kevin DTS")
Fixes: 981ed1bfbc ("pinctrl: Really force states during suspend/resume")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The memory node in fsl-ls1046a.dtsi has no 'reg' property, and causes
the dtc warning below.
Warning (unit_address_vs_reg): Node /memory@80000000 has a unit name, but no reg property
Let's add a 'reg' property with dummy memory size, since bootloader will
need to fill the correct one per board memory configuration anyway.
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Li Yang <leoyang.li@nxp.com>
This is the first set of bugfixes for ARM SoCs, fixing a couple
of stability problems, mostly on TI OMAP and Rockchips platforms:
- OMAP2 hwmod clocks must be enabled in the correct order
- OMAP3 Wakeup from resume through PRM IRQ was unreliable
- One regression on OMAP5 caused by a kexec fix
- Rockchip ethernet needs some settings for stable operation on Rock64
- Rockchip based Chrombook Plus needs another clock setting for
stable display suspend/resume
- Rockchip based phyCORE-RK3288 was able to run at an invalid
CPU clock frequency
- Rockchip MMC link was sometimes unreliable
- Multiple fixes to avoid crashes in the Broadcom STB DPFE driver
Other minor changes include:
- Devicetree fixes for incorrect hardware description (rockchip,
omap, Gemini, amlogic)
- Some MAINTAINER file updates to correct email and git addresses
- Some fixes addressing 'make W=1' dtc warnings (broadcom, amlogic,
cavium, qualcomm, hisilicon, zx)
- Fixes for LTO-compilation (orion, davinci, clps711x)
- One fix for an incorrect Kconfig errata selection
- A memory leak in the OMAP timer driver
- A kernel data leak in OMAP1 debugfs files
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fcv0
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is the first set of bugfixes for ARM SoCs, fixing a couple of
stability problems, mostly on TI OMAP and Rockchips platforms:
- OMAP2 hwmod clocks must be enabled in the correct order
- OMAP3 Wakeup from resume through PRM IRQ was unreliable
- one regression on OMAP5 caused by a kexec fix
- Rockchip ethernet needs some settings for stable operation on
Rock64
- Rockchip based Chrombook Plus needs another clock setting for
stable display suspend/resume
- Rockchip based phyCORE-RK3288 was able to run at an invalid CPU
clock frequency
- Rockchip MMC link was sometimes unreliable
- multiple fixes to avoid crashes in the Broadcom STB DPFE driver
Other minor changes include:
- Devicetree fixes for incorrect hardware description (rockchip,
omap, Gemini, amlogic)
- some MAINTAINER file updates to correct email and git addresses
- some fixes addressing 'make W=1' dtc warnings (broadcom, amlogic,
cavium, qualcomm, hisilicon, zx)
- fixes for LTO-compilation (orion, davinci, clps711x)
- one fix for an incorrect Kconfig errata selection
- a memory leak in the OMAP timer driver
- a kernel data leak in OMAP1 debugfs files"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
MAINTAINERS: update entries for ARM/STM32
ARM: dts: bcm283x: Move arm-pmu out of soc node
ARM: dts: bcm283x: Fix unit address of local_intc
ARM: dts: NSP: Fix amount of RAM on BCM958625HR
ARM: dts: Set D-Link DNS-313 SATA to muxmode 0
ARM: omap2: set CONFIG_LIRC=y in defconfig
ARM: dts: imx6dl: Include correct dtsi file for Engicam i.CoreM6 DualLite/Solo RQS
memory: brcmstb: dpfe: support new way of passing data from the DCPU
memory: brcmstb: dpfe: fix type declaration of variable "ret"
memory: brcmstb: dpfe: properly mask vendor error bits
ARM: BCM: dts: Remove leading 0x and 0s from bindings notation
ARM: orion: fix orion_ge00_switch_board_info initialization
ARM: davinci: mark spi_board_info arrays as const
ARM: clps711x: mark clps711x_compat as const
arm: zx: dts: Remove leading 0x and 0s from bindings notation
arm64: dts: Remove leading 0x and 0s from bindings notation
arm64: dts: cavium: fix PCI bus dtc warnings
MAINTAINERS: ARM: at91: update my email address
soc: imx: gpc: de-register power domains only if initialized
ARM: dts: rockchip: Fix DWMMC clocks
...
Currently the size of GICv2m MSI frames are listed as 4kB while the
Juno TRM specifies 64kB for each of these MSI frames.
Though the devices connected themselves might just use the first 4kB,
to be consistent with the general practice of 64kB boundary alignment
to all the devices, let's keep the size as 64kB. This might also help
in avoiding any surprise when passing the device to a VM.
This patch increases the size of each GICv2m MSI frames from 4kB to 64kB
as per the specification.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
It fixes LS family SoCs device tree dtc warning in IFC child nodes.
Warning (simple_bus_reg): Node /soc/ifc@1530000/nor@0,0 simple-bus unit address format error, expected "0"
Warning (simple_bus_reg): Node /soc/ifc@1530000/nand@1,0 simple-bus unit address format error, expected "100000000"
Warning (simple_bus_reg): Node /soc/ifc@1530000/board-control@2,0 simple-bus unit address format error, expected "200000000"
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the new bindings of the reworked Marvell NAND controller driver.
Also adapt the nand controller node organization to distinguish which
property is relevant for the controller, and which one is NAND chip
specific. Expose the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore as
the driver activates the arbiter by default for all boards (either
needed or harmless).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Use the new bindings of the reworked Marvell NAND controller driver.
Also adapt the nand controller node organization to distinguish which
property is relevant for the controller, and which one is NAND chip
specific. Expose the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore as
the driver activates the arbiter by default for all boards (either
needed or harmless).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the AHCI SATA
controller used on the Armada 7K/8K SoCs.
The ahci drivers was already designed to support up to 5 clocks so there
is only need to update the device tree to use it. It was not noticed
until now because of wrong assumption in the clock drivers, but as this
IP really needs 2 clocks, we had to declare both of them.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The routine pgattr_change_is_safe() was extended in commit 4e60205655
("arm64: mm: Permit transitioning from Global to Non-Global without BBM")
to permit changing the nG attribute from not set to set, but did so in a
way that inadvertently disallows such changes if other permitted attribute
changes take place at the same time. So update the code to take this into
account.
Fixes: 4e60205655 ("arm64: mm: Permit transitioning from Global to ...")
Cc: <stable@vger.kernel.org> # 4.14.x-
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Juno's GICv2m implementation consists of four frames providing 32
interrupts each. Since it is possible to plug in enough PCIe endpoints
to consume more than 32 MSIs, and the driver already has a bodge to
handle multiple frames, let's expose the other three as well.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Enable the Renesas R-Car M3-N (R8A77965) SoC in the ARM64 defconfig.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some 32bits guest OS can use the CNTP timer, however KVM does not
handle the accesses, injecting a fault instead.
Use the proper handlers to emulate the EL1 Physical Timer (CNTP)
register accesses of AArch32 guests.
Signed-off-by: Jérémy Fanguède <j.fanguede@virtualopensystems.com>
Signed-off-by: Alvise Rigo <a.rigo@virtualopensystems.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The HCR_EL2.TID3 flag needs to be set when trapping guest access to
the CPU ID registers is required. However, the decision about
whether to set this bit does not need to be repeated at every
switch to the guest.
Instead, it's sufficient to make this decision once and record the
outcome.
This patch moves the decision to vcpu_reset_hcr() and records the
choice made in vcpu->arch.hcr_el2. The world switch code can then
load this directly when switching to the guest without the need for
conditional logic on the critical path.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Suggested-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We don't currently limit guest accesses to the LOR registers, which we
neither virtualize nor context-switch. As such, guests are provided with
unusable information/controls, and are not isolated from each other (or
the host).
To prevent these issues, we can trap register accesses and present the
illusion LORegions are unssupported by the CPU. To do this, we mask
ID_AA64MMFR1.LO, and set HCR_EL2.TLOR to trap accesses to the following
registers:
* LORC_EL1
* LOREA_EL1
* LORID_EL1
* LORN_EL1
* LORSA_EL1
... when trapped, we inject an UNDEFINED exception to EL1, simulating
their non-existence.
As noted in D7.2.67, when no LORegions are implemented, LoadLOAcquire
and StoreLORelease must behave as LoadAcquire and StoreRelease
respectively. We can ensure this by clearing LORC_EL1.EN when a CPU's
EL2 is first initialized, as the host kernel will not modify this.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Vladimir Murzin <vladimir.murzin@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Pull cleanup patchlet from Thomas Gleixner:
"A single commit removing a bunch of bogus double semicolons all over
the tree"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
treewide/trivial: Remove ';;$' typo noise
According to PSCI standard v0.2, for CPU_SUSPEND call, which is
used by cpu idle framework, bit[16] of state parameter must be 0.
So update bit[16] of property 'arm,psci-suspend-param', which is
used as state parameter, to 0.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull networking fixes from David Miller:
1) Fix TTL offset calculation in mac80211 mesh code, from Peter Oh.
2) Fix races with procfs in ipt_CLUSTERIP, from Cong Wang.
3) Memory leak fix in lpm_trie BPF map code, from Yonghong Song.
4) Need to use GFP_ATOMIC in BPF cpumap allocations, from Jason Wang.
5) Fix potential deadlocks in netfilter getsockopt() code paths, from
Paolo Abeni.
6) Netfilter stackpointer size checks really are needed to validate
user input, from Florian Westphal.
7) Missing timer init in x_tables, from Paolo Abeni.
8) Don't use WQ_MEM_RECLAIM in mac80211 hwsim, from Johannes Berg.
9) When an ibmvnic device is brought down then back up again, it can be
sent queue entries from a previous session, handle this properly
instead of crashing. From Thomas Falcon.
10) Fix TCP checksum on LRO buffers in mlx5e, from Gal Pressman.
11) When we are dumping filters in cls_api, the output SKB is empty, and
the filter we are dumping is too large for the space in the SKB, we
should return -EMSGSIZE like other netlink dump operations do.
Otherwise userland has no signal that is needs to increase the size
of its read buffer. From Roman Kapl.
12) Several XDP fixes for virtio_net, from Jesper Dangaard Brouer.
13) Module refcount leak in netlink when a dump start fails, from Jason
Donenfeld.
14) Handle sub-optimal GSO sizes better in TCP BBR congestion control,
from Eric Dumazet.
15) Releasing bpf per-cpu arraymaps can take a long time, add a
condtional scheduling point. From Eric Dumazet.
16) Implement retpolines for tail calls in x64 and arm64 bpf JITs. From
Daniel Borkmann.
17) Fix page leak in gianfar driver, from Andy Spencer.
18) Missed clearing of estimator scratch buffer, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net_sched: gen_estimator: fix broken estimators based on percpu stats
gianfar: simplify FCS handling and fix memory leak
ipv6 sit: work around bogus gcc-8 -Wrestrict warning
macvlan: fix use-after-free in macvlan_common_newlink()
bpf, arm64: fix out of bounds access in tail call
bpf, x64: implement retpoline for tail call
rxrpc: Fix send in rxrpc_send_data_packet()
net: aquantia: Fix error handling in aq_pci_probe()
bpf: fix rcu lockdep warning for lpm_trie map_free callback
bpf: add schedule points in percpu arrays management
regulatory: add NUL to request alpha2
ibmvnic: Fix early release of login buffer
net/smc9194: Remove bogus CONFIG_MAC reference
net: ipv4: Set addr_type in hash_keys for forwarded case
tcp_bbr: better deal with suboptimal GSO
smsc75xx: fix smsc75xx_set_features()
netlink: put module reference if dump start fails
selftests/bpf/test_maps: exit child process without error in ENOMEM case
selftests/bpf: update gitignore with test_libbpf_open
selftests/bpf: tcpbpf_kern: use in6_* macros from glibc
..
Add SPDX identifier as was done by for example by:
"License cleanup: add SPDX GPL-2.0 license identifier to files with no
license" (commit <b24413180f5600bcb3bb70fbed5cf186b60864bd>)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch
"devicetree: Add compatible string for Zynq Ultrascale+ MPSoC"
(commit <988d6f07fc0a29e392035ba56e3bcfaf7b397d95>)
introduced specific compatible string for ZynqMP which should be used
first.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
do_task_stat() calls get_wchan(), which further does unwind_frame().
unwind_frame() restores frame->pc to original value in case function
graph tracer has modified a return address (LR) in a stack frame to hook
a function return. However, if function graph tracer has hit a filtered
function, then we can't unwind it as ftrace_push_return_trace() has
biased the index(frame->graph) with a 'huge negative'
offset(-FTRACE_NOTRACE_DEPTH).
Moreover, arm64 stack walker defines index(frame->graph) as unsigned
int, which can not compare a -ve number.
Similar problem we can have with calling of walk_stackframe() from
save_stack_trace_tsk() or dump_backtrace().
This patch fixes unwind_frame() to test the index for -ve value and
restore index accordingly before we can restore frame->pc.
Reproducer:
cd /sys/kernel/debug/tracing/
echo schedule > set_graph_notrace
echo 1 > options/display-graph
echo wakeup > current_tracer
ps -ef | grep -i agent
Above commands result in:
Unable to handle kernel paging request at virtual address ffff801bd3d1e000
pgd = ffff8003cbe97c00
[ffff801bd3d1e000] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 96000006 [#1] SMP
[...]
CPU: 5 PID: 11696 Comm: ps Not tainted 4.11.0+ #33
[...]
task: ffff8003c21ba000 task.stack: ffff8003cc6c0000
PC is at unwind_frame+0x12c/0x180
LR is at get_wchan+0xd4/0x134
pc : [<ffff00000808892c>] lr : [<ffff0000080860b8>] pstate: 60000145
sp : ffff8003cc6c3ab0
x29: ffff8003cc6c3ab0 x28: 0000000000000001
x27: 0000000000000026 x26: 0000000000000026
x25: 00000000000012d8 x24: 0000000000000000
x23: ffff8003c1c04000 x22: ffff000008c83000
x21: ffff8003c1c00000 x20: 000000000000000f
x19: ffff8003c1bc0000 x18: 0000fffffc593690
x17: 0000000000000000 x16: 0000000000000001
x15: 0000b855670e2b60 x14: 0003e97f22cf1d0f
x13: 0000000000000001 x12: 0000000000000000
x11: 00000000e8f4883e x10: 0000000154f47ec8
x9 : 0000000070f367c0 x8 : 0000000000000000
x7 : 00008003f7290000 x6 : 0000000000000018
x5 : 0000000000000000 x4 : ffff8003c1c03cb0
x3 : ffff8003c1c03ca0 x2 : 00000017ffe80000
x1 : ffff8003cc6c3af8 x0 : ffff8003d3e9e000
Process ps (pid: 11696, stack limit = 0xffff8003cc6c0000)
Stack: (0xffff8003cc6c3ab0 to 0xffff8003cc6c4000)
[...]
[<ffff00000808892c>] unwind_frame+0x12c/0x180
[<ffff000008305008>] do_task_stat+0x864/0x870
[<ffff000008305c44>] proc_tgid_stat+0x3c/0x48
[<ffff0000082fde0c>] proc_single_show+0x5c/0xb8
[<ffff0000082b27e0>] seq_read+0x160/0x414
[<ffff000008289e6c>] __vfs_read+0x58/0x164
[<ffff00000828b164>] vfs_read+0x88/0x144
[<ffff00000828c2e8>] SyS_read+0x60/0xc0
[<ffff0000080834a0>] __sys_trace_return+0x0/0x4
Fixes: 20380bb390 (arm64: ftrace: fix a stack tracer's output under function graph tracer)
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
[catalin.marinas@arm.com: replace WARN_ON with WARN_ON_ONCE]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
I recently noticed a crash on arm64 when feeding a bogus index
into BPF tail call helper. The crash would not occur when the
interpreter is used, but only in case of JIT. Output looks as
follows:
[ 347.007486] Unable to handle kernel paging request at virtual address fffb850e96492510
[...]
[ 347.043065] [fffb850e96492510] address between user and kernel address ranges
[ 347.050205] Internal error: Oops: 96000004 [#1] SMP
[...]
[ 347.190829] x13: 0000000000000000 x12: 0000000000000000
[ 347.196128] x11: fffc047ebe782800 x10: ffff808fd7d0fd10
[ 347.201427] x9 : 0000000000000000 x8 : 0000000000000000
[ 347.206726] x7 : 0000000000000000 x6 : 001c991738000000
[ 347.212025] x5 : 0000000000000018 x4 : 000000000000ba5a
[ 347.217325] x3 : 00000000000329c4 x2 : ffff808fd7cf0500
[ 347.222625] x1 : ffff808fd7d0fc00 x0 : ffff808fd7cf0500
[ 347.227926] Process test_verifier (pid: 4548, stack limit = 0x000000007467fa61)
[ 347.235221] Call trace:
[ 347.237656] 0xffff000002f3a4fc
[ 347.240784] bpf_test_run+0x78/0xf8
[ 347.244260] bpf_prog_test_run_skb+0x148/0x230
[ 347.248694] SyS_bpf+0x77c/0x1110
[ 347.251999] el0_svc_naked+0x30/0x34
[ 347.255564] Code: 9100075a d280220a 8b0a002a d37df04b (f86b694b)
[...]
In this case the index used in BPF r3 is the same as in r1
at the time of the call, meaning we fed a pointer as index;
here, it had the value 0xffff808fd7cf0500 which sits in x2.
While I found tail calls to be working in general (also for
hitting the error cases), I noticed the following in the code
emission:
# bpftool p d j i 988
[...]
38: ldr w10, [x1,x10]
3c: cmp w2, w10
40: b.ge 0x000000000000007c <-- signed cmp
44: mov x10, #0x20 // #32
48: cmp x26, x10
4c: b.gt 0x000000000000007c
50: add x26, x26, #0x1
54: mov x10, #0x110 // #272
58: add x10, x1, x10
5c: lsl x11, x2, #3
60: ldr x11, [x10,x11] <-- faulting insn (f86b694b)
64: cbz x11, 0x000000000000007c
[...]
Meaning, the tests passed because commit ddb55992b0 ("arm64:
bpf: implement bpf_tail_call() helper") was using signed compares
instead of unsigned which as a result had the test wrongly passing.
Change this but also the tail call count test both into unsigned
and cap the index as u32. Latter we did as well in 90caccdd8c
("bpf: fix bpf_tail_call() x64 JIT") and is needed in addition here,
too. Tested on HiSilicon Hi1616.
Result after patch:
# bpftool p d j i 268
[...]
38: ldr w10, [x1,x10]
3c: add w2, w2, #0x0
40: cmp w2, w10
44: b.cs 0x0000000000000080
48: mov x10, #0x20 // #32
4c: cmp x26, x10
50: b.hi 0x0000000000000080
54: add x26, x26, #0x1
58: mov x10, #0x110 // #272
5c: add x10, x1, x10
60: lsl x11, x2, #3
64: ldr x11, [x10,x11]
68: cbz x11, 0x0000000000000080
[...]
Fixes: ddb55992b0 ("arm64: bpf: implement bpf_tail_call() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
adding the grf-vio clock to the edp so that it can also be build
as module, correct pcie ep-gpio on the sapphire board and finally
a fix that makes the gmac work at gigabit speeds on the rk3328-rock64.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlqHdkUQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgVVtCACHTxf9/v7UFuXMDtcYRVKZaxwGe9U06RlU
CNRLJADT300B+feHRyh2WiJvNOX4ZJeDotYkXBe/73xMp9AeLv1gTwQBQD1juAfr
wZIXl5/P0zYFQV95oPgHOAGj89rMgvuHFGe2loO2GtIoAiZTcjNUel1SwUCNVzQL
OVei4Z0EGx0Nk5lEFChY0pSg0cZzDko+NGSYYPeQ1qtLJffuOZAq9tG0eJAlUted
qSCXKJnxy5cZ8FxLeuJmP2xGjiZMYLg20kr5DevRnpQTDCCP73VPIPv0IqO+YtfB
5Cmtf8cy/GNxcG1sgK1RMW6ytP+kmBX74I6xtpUAQtaQy1Ah4jDN
=QsKz
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rockchip-dts64fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts64 fixes for 4.16" from Heiko Stübner:
Fixes of dwmmc tuning clocks that may make probing HS cards fail,
adding the grf-vio clock to the edp so that it can also be build
as module, correct pcie ep-gpio on the sapphire board and finally
a fix that makes the gmac work at gigabit speeds on the rk3328-rock64.
* tag 'v4.16-rockchip-dts64fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix DWMMC clocks
arm64: dts: rockchip: introduce pclk_vio_grf in rk3399-eDP device node
arm64: dts: rockchip: correct ep-gpios for rk3399-sapphire
arm64: dts: rockchip: fix rock64 gmac2io stability issues
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dtc recently added PCI bus checks. Fix these warnings:
arch/arm64/boot/dts/cavium/thunder2-99xx.dtb: Warning (pci_bridge): Node /pci missing bus-range for PCI bridge
arch/arm64/boot/dts/cavium/thunder2-99xx.dtb: Warning (unit_address_vs_reg): Node /pci has a reg or ranges property, but no unit name
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
