Roel Kluin reported a bug in two error paths where skbs were wrongly
being freed using kfree(). He provided a fix where it was replaced to
kfree_skb(), as it should be.
However, in i2400mu_rx(), the error path was missing returning an
indication of the failure. Changed to reset rx_skb to NULL and return
it to the caller, i2400mu_rxd(). It will be treated as a transient
error and just ignore the packet.
Depending on the buffering conditions inside the device, the data
packet might be dropped or the device will signal the host again for
data-ready-to-read and the host will retry.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code was assuming PM was always enabled, which is not
correct. Code which accesses members in the struct usb_device that are
dependant on CONFIG_PM must be protected the same.
Reported by Randy Dunlap from a build error in the linux-next tree on
07/01/2009.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrate the i2400m driver into the kernel's build and Kconfig.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implements the backend so that the generic driver can TX/RX to/from
the SDIO device.
For RX, when data is ready the SDIO IRQ is fired and that will
allocate an skb, put all the data there and then pass it to the
generic driver RX code for processing and delivery.
TX, when kicked by the generic driver, will schedule work on a
driver-specific workqueue that pulls data from the TX FIFO and sends
it to the device until it drains it.
Thread contexts are needed as SDIO functions are blocking.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This implements the backends for the generic driver (i2400m) to be
able to load firmware to the SDIO device.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implements probe/disconnect for the SDIO device, as well as main
backends for the generic driver to control the SDIO device
(bus_dev_start(), bus_dev_stop() and bus_reset()).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This contains the common function declaration and constants for the
SDIO driver for the 2400m Wireless WiMAX Connection and it's debug
level settings.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implements the backend so that the generic driver can TX/RX to/from
the USB device.
TX is implemented with a kthread sitting in a never-ending loop that
when kicked by the generic driver's TX code will pull data from the TX
FIFO and send it to the device until it drains it. Then it goes back
sleep, waiting for another kick.
RX is implemented in a similar fashion, but reads are kicked in by the
device notifying in the interrupt endpoint that data is ready. Device
reset notifications are also sent via the notification endpoint.
We need a thread contexts to run USB autopm functions (blocking) and
to process the received data (can get to be heavy in processing
time).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This implements the backends for the generic driver (i2400m) to be
able to load firmware to the USB device.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implements probe/disconnect for the USB device, as well as main
backends for the generic driver to control the USB device
(bus_dev_start(), bus_dev_stop() and bus_reset()).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This contains the common function declaration and constants for the
USB driver for the 2400m Wireless WiMAX Connection, as well as it's
debug level settings.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Expose knobs to control the device (induce reset, power saving,
querying tx or rx stats, internal debug information and debug level
manipulation).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a collection of functions used to control the device (plus a
few helpers).
There are utilities for handling TLV buffers, hooks on the device's
reports to act on device changes of state [i2400m_report_hook()], on
acks to commands [i2400m_msg_ack_hook()], a helper for sending
commands to the device and blocking until a reply arrives
[i2400m_msg_to_dev()], a few high level commands for manipulating the
device state, powersaving mode and configuration plus the routines to
setup the device once communication is established with it
[i2400m_dev_initialize()].
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Handling of TX/RX data to/from the i2400m device (IP packets, control
and diagnostics). On RX, this parses the received read transaction
from the device, breaks it in chunks and passes it to the
corresponding subsystems (network and control).
Transmission to the device is done through a software FIFO, as
data/control frames can be coalesced (while the device is reading the
previous tx transaction, others accumulate). A FIFO is used because at
the end it is resource-cheaper that scatter/gather over USB. As well,
most traffic is going to be download (vs upload).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implements the firmware loader (using the bus-specific driver's
backends for the actual upload). The most critical thing in here is
the piece that puts the device in boot-mode from any other
(undetermined) state, otherwise, it is just pushing the bytes from the
firmware file to the device.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implementation of the glue to the network stack so the WiMAX device
shows up as an Ethernet device.
Initially we shot for implementing a Pure IP device -- however, the
world seems to turn around Ethernet devices. Main issues were with the
ISC DHCP client and servers (as they don't understand types other than
Ethernet and Token Ring).
We proceeded to register with IANA the PureIP hw type, so that DHCP
requests could declare such. We also created patches to the main ISC
DHCP versions to support it. However, until all that permeates into
deployments, there is going to be a long time.
So we moved back to wrap Ethernet frames around the PureIP device. At
the time being this has overhead; we need to reallocate with space for
an Ethernet header. The reason is the device-to-host protocol
coalesces many network packets into a single message, so we can't
introduce Ethernet headers without overwriting valid data from other
packets.
Coming-soon versions of the firmware have this issue solved.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implements the generic probe and disconnect functions that will be
called by the USB and SDIO driver's probe/disconnect functions.
Implements the backends for the WiMAX stack's basic operations:
message passing, rfkill control and reset.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wimax/i2400m.h defines the structures and constants for the
host-device protocols:
- boot / firmware upload protocol
- general data transport protocol
- control protocol
It is done in such a way that can also be used verbatim by user space.
drivers/net/wimax/i2400m.h defines all the APIs used by the core,
bus-generic driver (i2400m) and the bus specific drivers
(i2400m-BUSNAME). It also gives a roadmap to the driver
implementation.
debug-levels.h adds the core driver's debug settings.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
