This adds support for the OWL CM-160 electricity monitor to the cp210x
driver.
Signed-off-by: Luis Llorente <luisllorente@luisllorente.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1654) fixes a very old bug in ehci-hcd, connected with
scheduling of periodic split transfers. The calculations for
full/low-speed bus usage are all carried out after the correction for
bit-stuffing has been applied, but the values in the max_tt_usecs
array assume it hasn't been. The array should allow for allocation of
up to 90% of the bus capacity, which is 900 us, not 780 us.
The symptom caused by this bug is that any isochronous transfer to a
full-speed device with a maxpacket size larger than about 980 bytes is
always rejected with a -ENOSPC error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1653) fixes a bug in ehci-hcd. Unlike iTD entries, an
siTD entry in the periodic schedule may not complete until the frame
after the one it belongs to. Consequently, when scanning the periodic
schedule it is necessary to start with the frame _preceding_ the one
where the previous scan ended.
Not doing this properly can result in memory leaks and failures to
complete isochronous URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andy Leiserson <andy@leiserson.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1652) fixes a long-standing bug in ehci-hcd. The driver
relies on status polls to know when to stop port-resume signalling.
It uses the root-hub status timer to schedule these status polls. But
when the driver for the root hub is resumed, the timer is rescheduled
to go off immediately -- before the port is ready. When this happens
the timer does not get re-enabled, which prevents the port resume from
finishing until some other event occurs.
The symptom is that when a new device is plugged in, it doesn't get
recognized or enumerated until lsusb is run or something else happens.
The solution is to re-enable the root-hub status timer after every
status poll while a port resume is in progress.
This bug hasn't surfaced before now because we never used to try to
suspend the root hub in the middle of a port resume (except by
coincidence).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Norbert Preining <preining@logic.at>
Tested-by: Ming Lei <ming.lei@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1651) adds calls to the new
usb_hcd_{start,end}_port_resume() functions to uhci-hcd. Now UHCI
root hubs won't be runtime suspended while they are sending a resume
signal to one of their ports.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1650) adds calls to the new
usb_hcd_{start,end}_port_resume() functions to ehci-hcd. Now EHCI
root hubs won't be runtime suspended while they are sending a resume
signal to one of their ports.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1649) adds a mechanism for host controller drivers to
inform usbcore when they have begun or ended resume signalling on a
particular root-hub port. The core will then make sure that the root
hub does not get runtime-suspended while the port resume is going on.
Since commit 596d789a21 (USB: set hub's
default autosuspend delay as 0), the system tries to suspend hubs
whenever they aren't in use. While a root-hub port is being resumed,
the root hub does not appear to be in use. Attempted runtime suspends
fail because of the ongoing port resume, but the PM core just keeps on
trying over and over again. We want to prevent this wasteful effort.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1648) fixes a regression affecting nVidia EHCI
controllers. Evidently they don't like to have more than one async QH
unlinked at a time. I can't imagine how they manage to mess it up,
but at least one of them does.
The patch changes the async unlink logic in two ways:
Each time an IAA cycle is started, only the first QH on the
async unlink list is handled (rather than all of them).
Async QHs do not all get unlinked as soon as they have been
empty for long enough. Instead, only the last one (i.e., the
one that has been on the schedule the longest) is unlinked,
and then only if no other unlinks are in progress at the time.
This means that when multiple QHs are empty, they won't be unlinked as
quickly as before. That's okay; it won't affect correct operation of
the driver or add an excessive load. Multiple unlinks tend to be
relatively rare in any case.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Piergiorgio Sartor <piergiorgio.sartor@nexgo.de>
Cc: stable <stable@vger.kernel.org> # 3.6
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1647) attempts to work around a problem that seems to
affect some nVidia EHCI controllers. They sometimes take a very long
time to turn off their async or periodic schedules. I don't know if
this is a result of other problems, but in any case it seems wise not
to depend on schedule enables or disables taking effect in any
specific length of time.
The patch removes the existing 20-ms timeout for enabling and
disabling the schedules. The driver will now continue to poll the
schedule state at 1-ms intervals until the controller finally decides
to obey the most recent command issued by the driver. Just in case
this hides a problem, a debugging message will be logged if the
controller takes longer than 20 polls.
I don't know if this will actually fix anything, but it can't hurt.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Piergiorgio Sartor <piergiorgio.sartor@nexgo.de>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's six patches for xHCI and the USB core. There's a couple of
patches to fix xHCI 1.0 field formats, some memory leaks, dead ports,
and USB 3.0 remote wakeup disabling.
All of these are marked for stable.
I know I owe you some re-works of failed stable patches from my last
patchset round, but I don't think I'm going to get to them before I head
off to Linux Conf Australia tomorrow.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rgLf
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
USB/xhci: Misc fixes for 3.8.
Hi Greg,
Here's six patches for xHCI and the USB core. There's a couple of
patches to fix xHCI 1.0 field formats, some memory leaks, dead ports,
and USB 3.0 remote wakeup disabling.
All of these are marked for stable.
I know I owe you some re-works of failed stable patches from my last
patchset round, but I don't think I'm going to get to them before I head
off to Linux Conf Australia tomorrow.
Sarah Sharp
Pull btrfs fixes from Chris Mason:
"It turns out that we had two crc bugs when running fsx-linux in a
loop. Many thanks to Josef, Miao Xie, and Dave Sterba for nailing it
all down. Miao also has a new OOM fix in this v2 pull as well.
Ilya fixed a regression Liu Bo found in the balance ioctls for pausing
and resuming a running balance across drives.
Josef's orphan truncate patch fixes an obscure corruption we'd see
during xfstests.
Arne's patches address problems with subvolume quotas. If the user
destroys quota groups incorrectly the FS will refuse to mount.
The rest are smaller fixes and plugs for memory leaks."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (30 commits)
Btrfs: fix repeated delalloc work allocation
Btrfs: fix wrong max device number for single profile
Btrfs: fix missed transaction->aborted check
Btrfs: Add ACCESS_ONCE() to transaction->abort accesses
Btrfs: put csums on the right ordered extent
Btrfs: use right range to find checksum for compressed extents
Btrfs: fix panic when recovering tree log
Btrfs: do not allow logged extents to be merged or removed
Btrfs: fix a regression in balance usage filter
Btrfs: prevent qgroup destroy when there are still relations
Btrfs: ignore orphan qgroup relations
Btrfs: reorder locks and sanity checks in btrfs_ioctl_defrag
Btrfs: fix unlock order in btrfs_ioctl_rm_dev
Btrfs: fix unlock order in btrfs_ioctl_resize
Btrfs: fix "mutually exclusive op is running" error code
Btrfs: bring back balance pause/resume logic
btrfs: update timestamps on truncate()
btrfs: fix btrfs_cont_expand() freeing IS_ERR em
Btrfs: fix a bug when llseek for delalloc bytes behind prealloc extents
Btrfs: fix off-by-one in lseek
...
Pull cifs fixes from Steve French:
"Two small cifs fixes"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
fs/cifs/cifs_dfs_ref.c: fix potential memory leakage
cifs: fix srcip_matches() for ipv6
Pull ARM fixes from Russell King:
"A number of fixes:
Patrik found a problem with preempt counting in the VFP assembly
functions which can cause the preempt count to be upset.
Nicolas fixed a problem with the parsing of the DT when it straddles a
1MB boundary.
Subhash Jadavani reported a problem with sparsemem and our highmem
support for cache maintanence for DMA areas, and TI found a bug in
their strongly ordered memory mapping type.
Also, three fixes by way of Will Deacon's tree from Dave Martin for
instruction compatibility and Marc Zyngier to fix hypervisor boot mode
issues."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7629/1: mm: Fix missing XN flag for for MT_MEMORY_SO
ARM: DMA: Fix struct page iterator in dma_cache_maint() to work with sparsemem
ARM: 7628/1: head.S: map one extra section for the ATAG/DTB area
ARM: 7627/1: Predicate preempt logic on PREEMP_COUNT not PREEMPT alone
ARM: virt: simplify __hyp_stub_install epilog
ARM: virt: boot secondary CPUs through the right entry point
ARM: virt: Avoid bx instruction for compatibility with <=ARMv4
Here's a long-pending fixes pull request for arm-soc (I didn't send one
in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted to
multiplatform on i.MX, which was causing build failures when included
- Device tree updates for at91 dealing mostly with their new
pinctrl setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YDHs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a long-pending fixes pull request for arm-soc (I didn't send
one in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted
to multiplatform on i.MX, which was causing build failures when
included
- Device tree updates for at91 dealing mostly with their new pinctrl
setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc."
* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
...
* Two cpuidle initialization fixes from Konrad Rzeszutek Wilk.
* cpufreq regression fixes for AMD processors from Borislav Petkov,
Stefan Bader, and Matthew Garrett.
* ACPI cpufreq fix from Thomas Schlichter.
* cpufreq and devfreq fixes related to incorrect usage of operating
performance points (OPP) framework and RCU from Nishanth Menon.
* APEI workaround for incorrect BIOS information from Lans Zhang.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=EEk8
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Two cpuidle initialization fixes from Konrad Rzeszutek Wilk.
- cpufreq regression fixes for AMD processors from Borislav Petkov,
Stefan Bader, and Matthew Garrett.
- ACPI cpufreq fix from Thomas Schlichter.
- cpufreq and devfreq fixes related to incorrect usage of operating
performance points (OPP) framework and RCU from Nishanth Menon.
- APEI workaround for incorrect BIOS information from Lans Zhang.
* tag 'pm+acpi-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Add module aliases for acpi-cpufreq
ACPI: Check MSR valid bit before using P-state frequencies
PM / devfreq: exynos4_bus: honor RCU lock usage
PM / devfreq: add locking documentation for recommended_opp
cpufreq: cpufreq-cpu0: use RCU locks around usage of OPP
cpufreq: OMAP: use RCU locks around usage of OPP
ACPI, APEI: Fixup incorrect 64-bit access width firmware bug
ACPI / processor: Get power info before updating the C-states
powernow-k8: Add a kconfig dependency on acpi-cpufreq
ACPI / cpuidle: Fix NULL pointer issues when cpuidle is disabled
intel_idle: Don't register CPU notifier if we are not running.
One more oversight in the debugfs code was reported and fixed, plus a
documentation fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=O6T4
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"One more oversight in the debugfs code was reported and fixed, plus a
documentation fix."
* tag 'regmap-fix-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix small typo in regmap_bulk_write comment
regmap: debugfs: Fix seeking from the cache
Pull slave-dmaengine fixes from Vinod Koul:
"A few fixes on slave dmanengine. There are trivial fixes in imx-dma,
tegra-dma & ioat driver"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: implement flags parameters for cyclic transfer
dmaengine: imx-dma: Disable use of hw_chain to fix sg_dma transfers.
ioat: Fix DMA memory sync direction correct flag
Usb3.0 device defines function remote wakeup which is only for interface
recipient rather than device recipient. This is different with usb2.0 device's
remote wakeup feature which is defined for device recipient. According usb3.0
spec 9.4.5, the function remote wakeup can be modified by the SetFeature()
requests using the FUNCTION_SUSPEND feature selector. This patch is to use
correct way to disable usb3.0 device's function remote wakeup after suspend
error and resuming.
This should be backported to kernels as old as 3.4, that contain the
commit 623bef9e03 "USB/xhci: Enable remote
wakeup for USB3 devices."
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When the xHCI driver is not available, actively switch the ports to EHCI
mode since some BIOSes leave them in xHCI mode where they would
otherwise appear dead. This was discovered on a Dell Optiplex 7010,
but it's possible other systems could be affected.
This should be backported to kernels as old as 3.0, that contain the
commit 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: David Moore <david.moore@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch (as1640) fixes a memory leak in xhci-hcd. The urb_priv
data structure isn't always deallocated in the handle_tx_event()
routine for non-control transfers. The patch adds a kfree() call so
that all paths end up freeing the memory properly.
This patch should be backported to kernels as old as 2.6.36, that
contain the commit 8e51adccd4 "USB: xHCI:
Introduce urb_priv structure"
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-and-tested-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
CC: <stable@vger.kernel.org>
Fix incorrect bit test that originally showed up in
4ee823b83b "USB/xHCI: Support
device-initiated USB 3.0 resume."
Use '&' instead of '&&'.
This should be backported to kernels as old as 3.4.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
To calculate the TD size for a particular TRB in an isoc TD, we need
know the endpoint's max packet size. Isochronous endpoints also encode
the number of additional service opportunities in their wMaxPacketSize
field. The TD size calculation did not mask off those bits before using
the field. This resulted in incorrect TD size information for
isochronous TRBs when an URB frame buffer crossed a 64KB boundary.
For example:
- an isoc endpoint has 2 additional service opportunites and
a max packet size of 1020 bytes
- a frame transfer buffer contains 3060 bytes
- one frame buffer crosses a 64KB boundary, and must be split into
one 1276 byte TRB, and one 1784 byte TRB.
The TD size is is the number of packets that remain to be transferred
for a TD after processing all the max packet sized packets in the
current TRB and all previous TRBs.
For this TD, the number of packets to be transferred is (3060 / 1020),
or 3. The first TRB contains 1276 bytes, which means it contains one
full packet, and a 256 byte remainder. After processing all the max
packet-sized packets in the first TRB, the host will have 2 packets left
to transfer.
The old code would calculate the TD size for the first TRB as:
total packet count = DIV_ROUND_UP (TD length / endpoint wMaxPacketSize)
total packet count - (first TRB length / endpoint wMaxPacketSize)
The math should have been:
total packet count = DIV_ROUND_UP (3060 / 1020) = 3
3 - (1276 / 1020) = 2
Since the old code didn't mask off the additional service interval bits
from the wMaxPacketSize field, the math ended up as
total packet count = DIV_ROUND_UP (3060 / 5116) = 1
1 - (1276 / 5116) = 1
Fix this by masking off the number of additional service opportunities
in the wMaxPacketSize field.
This patch should be backported to stable kernels as old as 3.0, that
contain the commit 4da6e6f247 "xhci 1.0:
Update TD size field format." It may not apply well to kernels older
than 3.2 because of commit 29cc88979a
"USB: use usb_endpoint_maxp() instead of le16_to_cpu()".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
An isochronous TD is comprised of one isochronous TRB chained to zero or
more normal TRBs. Only the isoc TRB has the TBC and TLBPC fields. The
normal TRBs must set those fields to zeroes. The code was setting the
TBC and TLBPC fields for both isoc and normal TRBs. Fix this.
This should be backported to stable kernels as old as 3.0, that contain
the commit b61d378f2d " xhci 1.0: Set
transfer burst last packet count field."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
btrfs_start_delalloc_inodes() locks the delalloc_inodes list, fetches the
first inode, unlocks the list, triggers btrfs_alloc_delalloc_work/
btrfs_queue_worker for this inode, and then it locks the list, checks the
head of the list again. But because we don't delete the first inode that it
deals with before, it will fetch the same inode. As a result, this function
allocates a huge amount of btrfs_delalloc_work structures, and OOM happens.
Fix this problem by splice this delalloc list.
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
The max device number of single profile is 1, not 0 (0 means 'as many as
possible'). Fix it.
Cc: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
First, though the current transaction->aborted check can stop the commit early
and avoid unnecessary operations, it is too early, and some transaction handles
don't end, those handles may set transaction->aborted after the check.
Second, when we commit the transaction, we will wake up some worker threads to
flush the space cache and inode cache. Those threads also allocate some transaction
handles and may set transaction->aborted if some serious error happens.
So we need more check for ->aborted when committing the transaction. Fix it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
We may access and update transaction->aborted on the different CPUs without
lock, so we need ACCESS_ONCE() wrapper to prevent the compiler from creating
unsolicited accesses and make sure we can get the right value.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
I noticed a WARN_ON going off when adding csums because we were going over
the amount of csum bytes that should have been allowed for an ordered
extent. This is a leftover from when we used to hold the csums privately
for direct io, but now we use the normal ordered sum stuff so we need to
make sure and check if we've moved on to another extent so that the csums
are added to the right extent. Without this we could end up with csums for
bytenrs that don't have extents to cover them yet. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
For compressed extents, the range of checksum is covered by disk length,
and the disk length is different with ram length, so we need to use disk
length instead to get us the right checksum.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
A user reported a BUG_ON(ret) that occured during tree log replay. Ret was
-EAGAIN, so what I think happened is that we removed an extent that covered
a bitmap entry and an extent entry. We remove the part from the bitmap and
return -EAGAIN and then search for the next piece we want to remove, which
happens to be an entire extent entry, so we just free the sucker and return.
The problem is ret is still set to -EAGAIN so we trip the BUG_ON(). The
user used btrfs-zero-log so I'm not 100% sure this is what happened so I've
added a WARN_ON() to catch the other possibility. Thanks,
Reported-by: Jan Steffens <jan.steffens@gmail.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
We drop the extent map tree lock while we're logging extents, so somebody
could come in and merge another extent into this one and screw up our
logging, or they could even remove us from the list which would keep us from
logging the extent or freeing our ref on it, so we need to make sure to not
clear LOGGING until after the extent is logged, and then we can merge it to
adjacent extents. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
From Pawel Moll:
- makes the V2P-CA15_A7 (a.k.a. TC2) work with 3.8 kernels
- improves vexpress-sysreg.c behaviour on arm64 platforms
* 'vexpress/fixes' of git://git.linaro.org/people/pawelmoll/linux:
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
One RM9200 setup option is the only C code change.
Some documentation changes can clarify the pinctrl use.
Then, some defconfig modifications are allowing the affected platforms
to boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRAPnqAAoJEAf03oE53VmQbeUH/04lzIgUv63RX2zQFD6Fi1zD
IeYBhfzeSP65CPMqyFnw+lrHUdCWn0JYdFM6/x7J8n1k2+SY3T7N95k5oXlnqO6e
pT/XGontWQIZkyL0jkrawbs5QtE0OYnkm8Ge97qlhul4XoIiyWLFFGDHE36dzcv/
K4FPrG9PVVhjFIiZB+v5I3CnhzLWJvozn9J2ceIZ5d0Z9dwLuHWgXGu6OM2ZRvOw
LR1r2YpnGTKUT0am6tmWm1W7PY6ZQOQXmx5qX/H2X6gRQdq690baYUTOYPK3ZckX
kdEa+pCOQHY1GgimFzUzAVfoCyYwllo1yAWaK2a4qR4kxcaeGd1BYqlKeCFIfRc=
=aKwA
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre:
Here are fixes for AT91 that are mainly related to device tree.
One RM9200 setup option is the only C code change.
Some documentation changes can clarify the pinctrl use.
Then, some defconfig modifications are allowing the affected platforms
to boot.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
The vexpress-sysreg driver does not have to be initialized
early, when the platform doesn't require this. Unfortunately
in such case it wasn't initialized correctly - master site
lookup and config bridge registration were missing. Fixed now.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
As the kernel is able to cope with multiple clusters,
uncomment the A7 cores in the Device Tree for V2P-CA15_A7
tile, making all 5 cores available to the user.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
In ARM multi-cluster systems the MPIDR affinity level 0 cannot be used as a
single cpu identifier, affinity levels 1 and 2 must be taken into account as
well.
This patch extends the MPIDR usage to affinity levels 1 and 2 in versatile
secondary cores start up code in order to compare the passed pen_release
value with the full-blown affinity mask.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
maintainer for some time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ/qTBAAoJEFBXWFqHsHzOnNcH/0F8Ul4CJLS/+K80UaJDn7RQ
Di+4zPi/7foByJEUdTC9jDetHREPMeRLX2hzR+2XK+zCtrFPV8VAw4crdxOmLRYb
CxlTuMVA2R68NwvH1+PqTvuiJ6Qxr0HZHzmQdj+x8hWgRkD0RRoD/KQVbkrp8OKh
jJICgd3BXe9GTJszqK13Gj4VOfZvF9YyYDKAiKojfEOV3PyJTdnMBYGGQUD+6FHE
YxfG2xVUh/diFGpWxC5DLQdZ2ow+/7ruPTG+FifVGMcdqYI/KZ/l6cHiHNcFJcQs
6isObI8LeZ87kWJpM/cylqkzyyRGwg12jlFup22CBQCRyWgrgnGNVdoVBuffKJ0=
=Bup/
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.8-3' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
This is yet another critical imxfb fixes held off by absence of FB
maintainer for some time.
* tag 'imx-fixes-3.8-3' of git://git.linaro.org/people/shawnguo/linux-2.6:
video: imxfb: Do not crash on reboot
- fix memory leak in mvebu/clk-cpu.c
- use devm_ to correct/simplify error paths in mvsdio
- add missing #interrupt-cells property in kirkwood
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQ/zvKAAoJEAi3KVZQDZAebCIIAKCaI3zYiHku7Q52Auzog0oU
7Gk6/TpZtolZURusjSVo8ZPWoZhJc9SoFAVkVJPcB9j1xTl3K7iNVOj4DVvi66o2
R8dw85nTKryBc6kapiJEpQhJof9dQKzmNSL36TNLaHjPef/hz3gVn/QqOxmyuBro
ZZI0aUm+idgaDFkQCuevcfuStQGaKdOsIr23QEbicTj0rbgy0OIKrQ2KxFGKnr0Z
YYYjUr9M5wk1mSOsssEcE/a97eejHS201JhYvCfxSpWCjbwiaErg0fzns7wZ2hhV
BKGAEs+M67gcaHR/Pi2fy3LNLtwIcVNNgFYF3aCiBEFQ+hqtar6O9zqSmlBk1bI=
=xOtK
-----END PGP SIGNATURE-----
Merge tag 'mvebu_fixes_for_v3.8-rc5' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
mvebu fixes for v3.8-rc5
- fix memory leak in mvebu/clk-cpu.c
- use devm_ to correct/simplify error paths in mvsdio
- add missing #interrupt-cells property in kirkwood
* tag 'mvebu_fixes_for_v3.8-rc5' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
Here are some more USB fixes for the 3.8-rc4 tree.
Some gadget driver fixes, and finally resolved the ehci-mxc driver build issues
(it's just some code moving around and being deleted).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEAeCEACgkQMUfUDdst+ynRygCeNs8Z0Nt+/quZHKf+/DS4vlRt
vBYAnAxbcPg1zWhMM+8AVt/YFYp83sfP
=5UpK
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull more USB fixes from Greg Kroah-Hartman:
"Here are some more USB fixes for the 3.8-rc4 tree.
Some gadget driver fixes, and finally resolved the ehci-mxc driver
build issues (it's just some code moving around and being deleted)."
* tag 'usb-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: EHCI: fix build error in ehci-mxc
USB: EHCI: add a name for the platform-private field
USB: EHCI: fix incorrect configuration test
USB: EHCI: Move definition of EHCI_STATS to ehci.h
USB: UHCI: fix IRQ race during initialization
usb: gadget: FunctionFS: Fix missing braces in parse_opts
usb: dwc3: gadget: fix ep->maxburst for ep0
ARM: i.MX clock: Change the connection-id for fsl-usb2-udc
usb: gadget: fsl_mxc_udc: replace MX35_IO_ADDRESS to ioremap
usb: gadget: fsl-mxc-udc: replace cpu_is_xxx() with platform_device_id
usb: musb: cppi_dma: drop '__init' annotation
Here is a single revert for the ti-st misc driver, fixing problem that was
introduced in 3.7-rc1 that has been bothering people.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEAdxcACgkQMUfUDdst+ynQOgCgmsqcz6DaKFQpcMNKEl/6GWz2
KA4AoNYW3uSDQn1TUbuKmoJSN/SYALK4
=xqHP
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull drivers/misc fix from Greg Kroah-Hartman:
"Here is a single revert for the ti-st misc driver, fixing problem that
was introduced in 3.7-rc1 that has been bothering people."
* tag 'char-misc-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "drivers/misc/ti-st: remove gpio handling"
Just a MAINTAINERS update, now that Alan has left for a bit, I'll
continue to watch over the serial drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEAdpEACgkQMUfUDdst+ym9cQCeLtZjj8FAz+VYcmHXFtJ9gK1C
9aEAn35RUUbVVZwN2QtIomah5Uz+2qPz
=KYh4
-----END PGP SIGNATURE-----
Merge tag 'tty-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull a TTY maintainer patch from Greg Kroah-Hartman:
"Just a MAINTAINERS update, now that Alan has left for a bit, I'll
continue to watch over the serial drivers."
* tag 'tty-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
MAINTAINERS: Someone needs to watch over the serial drivers
Pull media fixes from Mauro Carvalho Chehab:
- gspca: add needed delay for I2C traffic for sonixb/sonixj cameras
- gspca: add one missing Kinect USB ID
- usbvideo: some regression fixes
- omap3isp: fix some build issues
- videobuf2: fix video output handling
- exynos s5p/m5mols: a few regression fixes.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
[media] omap3isp: Don't include <plat/cpu.h>
[media] s5p-mfc: Fix interrupt error handling routine
[media] s5p-fimc: Fix return value of __fimc_md_create_flite_source_links()
[media] m5mols: Fix typo in get_fmt callback
[media] v4l: vb2: Set data_offset to 0 for single-plane output buffers
[media] [FOR,v3.8] omap3isp: Don't include deleted OMAP plat/ header files
[media] gspca_sonixj: Add a small delay after i2c_w1
[media] gspca_sonixb: Properly wait between i2c writes
[media] gspca_kinect: add Kinect for Windows USB id
Pull m68k fixes from Geert Uytterhoeven:
"The asm-generic changeset has been ack'ed by Arnd."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up finit_module
asm-generic/dma-mapping-broken.h: Provide dma_alloc_attrs()/dma_free_attrs()
m68k: Provide dma_alloc_attrs()/dma_free_attrs()
