Filters array is coped from user space and linked to the j1939 socket.
On socket release this memory was not freed.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently the error return paths do not free skb and this results in a
memory leak. Fix this by freeing them before the return.
Addresses-Coverity: ("Resource leak")
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
While the ti_hecc has interrupts to report when the error counters increase
to a certain level and which change state it doesn't handle the case that
the error counters go down again, so the reported state can actually be
wrong. Since there is no interrupt for that, do update state based on the
error counters, when the state is not error active and goes down again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The HECC_CANES register handles the flags specially, it only updates
the flags after a one is written to them. Since the interrupt for
frame errors is not enabled an old error can hence been seen when a
state interrupt arrives. For example if the device is not connected
to the CAN-bus the error warning interrupt will have HECC_CANES
indicating there is no ack. The error passive interrupt thereafter
will have HECC_CANES flagging that there is a warning level. And if
thereafter there is a message successfully send HECC_CANES points to
an error passive event, while in reality it became error warning
again. In summary, the state is not always reported correctly.
So handle the state changes and frame errors separately. The state
changes are now based on the interrupt flags and handled directly
when they occur. The reporting of the frame errors is still done as
before, as a side effect of another interrupt.
note: the hecc_clear_bit will do a read, modify, write. So it will
not only clear the bit, but also reset all other bits being set as
a side affect, hence it is replaced with only clearing the flags.
note: The HECC_CANMC_CCR is no longer cleared in the state change
interrupt, it is completely unrelated.
And use net_ratelimit to make checkpatch happy.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the rx FIFO overflows the ti_hecc would silently drop them since
the overwrite protection is enabled for all mailboxes. So disable it for
the lowest priority mailbox and return a proper error value when receive
message lost is set. Drop the message itself in that case, since it
might be partially updated.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Release the mailbox after reading it, so it can be reused a bit earlier.
Since "can: rx-offload: continue on error" all pending message bits are
cleared directly, so remove clearing them in ti_hecc.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The HECC_CANMIM is set in the xmit path and cleared in the interrupt.
Since this is done with a read, modify, write action the register might
end up with some more MIM enabled then intended, since it is not
protected. That doesn't matter at all, since the tx interrupt disables
the mailbox with HECC_CANME (while holding a spinlock). So lets just
always keep MIM set.
While at it, since the mailbox direction never changes, don't set it
every time a message is send, ti_hecc_reset() already sets them to tx.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the interface goes down, the CPK should no longer take an active
part in the CAN-bus communication, like sending acks and error frames.
So enable configuration mode in ti_hecc_stop, so the CPK is no longer
active.
When a transceiver switch is present the acks and errors don't make it
to the bus, but disabling the CPK then does prevent oddities, like
ti_hecc_reset() failing, since the CPK can become bus-off and starts
counting the 11 bit recessive bits, which seems to block the reset. It
can also cause invalid interrupts and disrupt the CAN-bus, since
transmission can be stopped in the middle of a message, by disabling the
tranceiver while the CPK is sending.
Since the CPK is disabled after normal power on, it is typically only
seen when the interface is restarted.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
If the hardware FIFO is empty can_rx_offload_offload_one() will return
NULL.
In case a CAN frame was read from the hardware,
can_rx_offload_offload_one() returns the skb containing it.
Without this patch can_rx_offload_irq_offload_fifo() bails out if no skb
returned, regardless of the reason.
Similar to can_rx_offload_irq_offload_timestamp() in case of a resource
shortage the whole FIFO should be discarded, to avoid an IRQ storm and
give the system some time to recover. However if the FIFO is empty the
loop can be left.
With this patch the loop is left in case of empty FIFO, but not on
errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
However can_rx_offload_irq_offload_timestamp() bails out in the error
case. In case of a resource shortage all mailboxes should be discarded,
to avoid an IRQ storm and give the system some time to recover.
Since can_rx_offload_irq_offload_timestamp() is typically called from a
while loop, all message will eventually be discarded. So let's continue
on error instead to discard them directly.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Before this patch can_rx_offload_offload_one() returns a pointer to a
skb containing the read CAN frame or a NULL pointer.
However the meaning of the NULL pointer is ambiguous, it can either mean
the requested mailbox is empty or there was an error.
This patch fixes this situation by returning:
- pointer to skb on success
- NULL pointer if mailbox is empty
- ERR_PTR() in case of an error
All users of can_rx_offload_offload_one() have been adopted, no
functional change intended.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the rx-offload skb_queue is full or the skb allocation fails (due to OOM),
the mailbox contents is discarded.
This patch adds the incrementing of the rx_fifo_errors statistics counter.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The skb_queue is a linked list, holding the skb to be processed in the
next NAPI call.
Without this patch, the queue length in can_rx_offload_offload_one() is
limited to skb_queue_len_max + 1. As the skb_queue is a linked list, no
array or other resources are accessed out-of-bound, however this
behaviour is counterintuitive.
This patch limits the rx-offload skb_queue length to skb_queue_len_max.
Fixes: d254586c34 ("can: rx-offload: Add support for HW fifo based irq offloading")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the rx-offload skb_queue is full can_rx_offload_queue_tail() will not
queue the skb and return with an error.
This patch frees the skb in case of a full queue, which brings
can_rx_offload_queue_tail() in line with the
can_rx_offload_queue_sorted() function, which has been adjusted in the
previous patch.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the caller.
Fixes: d254586c34 ("can: rx-offload: Add support for HW fifo based irq offloading")
Reported-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the rx-offload skb_queue is full can_rx_offload_queue_sorted() will
not queue the skb and return with an error.
None of the callers of this function, issue a kfree_skb() to free the
not queued skb. This results in a memory leak.
This patch fixes the problem by freeing the skb in case of a full queue.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the callers, as this function might
be used in both the rx and tx path.
Fixes: 55059f2b7f ("can: rx-offload: introduce can_rx_offload_get_echo_skb() and can_rx_offload_queue_sorted() functions")
Cc: linux-stable <stable@vger.kernel.org>
Cc: Martin Hundebøll <martin@geanix.com>
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
AXI CANIP doesn't support tx fifo empty interrupt feature(TXFEMP),
update the flags filed in the driver for AXI CAN case accordingly.
Fixes: 3281b380ec ("can: xilinx_can: Fix flags field initialization for axi can and canps")
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
While the state is updated when the error counters increase and
decrease, there is no event when the bus recovers and the error counters
decrease again. So add that event as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Tested-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the CAN interface is closed it the hardwre is put in power down
mode, but does not reset the error counters / state. Reset the D_CAN on
open, so the reported state and the actual state match.
According to [1], the C_CAN module doesn't have the software reset.
[1] http://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the status register is read without the status IRQ pending, the
chip may not raise the interrupt line for an upcoming status interrupt
and the driver may miss a status interrupt.
It is critical that the BUSOFF status interrupt is forwarded to the
higher layers, since no more interrupts will follow without
intervention.
Thanks to Wolfgang and Joe for bringing up the first idea.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Joe Burmeister <joe.burmeister@devtank.co.uk>
Fixes: fa39b54ccf ("can: c_can: Get rid of pointless interrupts")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
While the state changes are reported when the error counters increase
and decrease, there is no event when the bus recovers and the error
counters decrease again. So add those as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix a small slab info leak due to a failure to clear the command buffer
at allocation.
The first 16 bytes of the command buffer are always sent to the device
in pcan_usb_send_cmd() even though only the first two may have been
initialised in case no argument payload is provided (e.g. when waiting
for a response).
Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Cc: stable <stable@vger.kernel.org> # 3.4
Reported-by: syzbot+863724e7128e14b26732@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When decoding a buffer received from PCAN-USB, the first timestamp read in
a packet is a 16-bit coded time base, and the next ones are an 8-bit
offset to this base, regardless of the type of packet read.
This patch corrects a potential loss of synchronization by using a
timestamp index read from the buffer, rather than an index of received
data packets, to determine on the sizeof the timestamp to be read from the
packet being decoded.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Fixes: 46be265d33 ("can: usb: PEAK-System Technik PCAN-USB specific part")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The ECC (memory error detection and correction) mechanism can be
activated or not, controlled by the ECCDIS bit in CAN_MECR. When
disabled, updates on indications and reporting registers are stopped.
So if want to disable ECC completely, had better assert ECCDIS bit, not
just mask the related interrupts.
Fixes: cdce844865 ("can: flexcan: add vf610 support for FlexCAN")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver was accessing its driver data after having freed it.
Fixes: 0024d8ad16 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Cc: stable <stable@vger.kernel.org> # 3.9
Cc: Bernd Krumboeck <b.krumboeck@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver was accessing its driver data after having freed it.
Fixes: 51f3baad7d ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: stable <stable@vger.kernel.org> # 4.12
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Reported-by: syzbot+e29b17e5042bbc56fae9@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In gs_can_open() if usb_submit_urb() fails the allocated urb should be
released.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
of_node_put() needs to be called when the device node which is got
from of_get_child_by_name() finished using.
Fixes: 2290aefa2e ("can: dev: Add support for limiting configured bitrate")
Cc: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For some reason I missed the case of DCCP passive
flows in my previous patch.
Fixes: a904a0693c ("inet: stop leaking jiffies on the wire")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Thiemo Nagel <tnagel@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix free/alloc races in batmanadv, from Sven Eckelmann.
2) Several leaks and other fixes in kTLS support of mlx5 driver, from
Tariq Toukan.
3) BPF devmap_hash cost calculation can overflow on 32-bit, from Toke
Høiland-Jørgensen.
4) Add an r8152 device ID, from Kazutoshi Noguchi.
5) Missing include in ipv6's addrconf.c, from Ben Dooks.
6) Use siphash in flow dissector, from Eric Dumazet. Attackers can
easily infer the 32-bit secret otherwise etc.
7) Several netdevice nesting depth fixes from Taehee Yoo.
8) Fix several KCSAN reported errors, from Eric Dumazet. For example,
when doing lockless skb_queue_empty() checks, and accessing
sk_napi_id/sk_incoming_cpu lockless as well.
9) Fix jumbo packet handling in RXRPC, from David Howells.
10) Bump SOMAXCONN and tcp_max_syn_backlog values, from Eric Dumazet.
11) Fix DMA synchronization in gve driver, from Yangchun Fu.
12) Several bpf offload fixes, from Jakub Kicinski.
13) Fix sk_page_frag() recursion during memory reclaim, from Tejun Heo.
14) Fix ping latency during high traffic rates in hisilicon driver, from
Jiangfent Xiao.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (146 commits)
net: fix installing orphaned programs
net: cls_bpf: fix NULL deref on offload filter removal
selftests: bpf: Skip write only files in debugfs
selftests: net: reuseport_dualstack: fix uninitalized parameter
r8169: fix wrong PHY ID issue with RTL8168dp
net: dsa: bcm_sf2: Fix IMP setup for port different than 8
net: phylink: Fix phylink_dbg() macro
gve: Fixes DMA synchronization.
inet: stop leaking jiffies on the wire
ixgbe: Remove duplicate clear_bit() call
Documentation: networking: device drivers: Remove stray asterisks
e1000: fix memory leaks
i40e: Fix receive buffer starvation for AF_XDP
igb: Fix constant media auto sense switching when no cable is connected
net: ethernet: arc: add the missed clk_disable_unprepare
igb: Enable media autosense for the i350.
igb/igc: Don't warn on fatal read failures when the device is removed
tcp: increase tcp_max_syn_backlog max value
net: increase SOMAXCONN to 4096
netdevsim: Fix use-after-free during device dismantle
...
Stable bugfixes:
- Fix an RCU lock leak in nfs4_refresh_delegation_stateid()
Other fixes:
- The TCP back channel mustn't disappear while requests are outstanding
- The RDMA back channel mustn't disappear while requests are outstanding
- Destroy the back channel when we destroy the host transport
- Don't allow a cached open with a revoked delegation
-----BEGIN PGP SIGNATURE-----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=ttcU
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.4-3' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client bugfixes from Anna Schumaker:
"This contains two delegation fixes (with the RCU lock leak fix marked
for stable), and three patches to fix destroying the the sunrpc back
channel.
Stable bugfixes:
- Fix an RCU lock leak in nfs4_refresh_delegation_stateid()
Other fixes:
- The TCP back channel mustn't disappear while requests are
outstanding
- The RDMA back channel mustn't disappear while requests are
outstanding
- Destroy the back channel when we destroy the host transport
- Don't allow a cached open with a revoked delegation"
* tag 'nfs-for-5.4-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS: Fix an RCU lock leak in nfs4_refresh_delegation_stateid()
NFSv4: Don't allow a cached open with a revoked delegation
SUNRPC: Destroy the back channel when we destroy the host transport
SUNRPC: The RDMA back channel mustn't disappear while requests are outstanding
SUNRPC: The TCP back channel mustn't disappear while requests are outstanding
-----BEGIN PGP SIGNATURE-----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=+rar
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20191101' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Two small nvme fixes, one is a fabrics connection fix, the other one
a cleanup made possible by that fix (Anton, via Keith)
- Fix requeue handling in umb ubd (Anton)
- Fix spin_lock_irq() nesting in blk-iocost (Dan)
- Three small io_uring fixes:
- Install io_uring fd after done with ctx (me)
- Clear ->result before every poll issue (me)
- Fix leak of shadow request on error (Pavel)
* tag 'for-linus-20191101' of git://git.kernel.dk/linux-block:
iocost: don't nest spin_lock_irq in ioc_weight_write()
io_uring: ensure we clear io_kiocb->result before each issue
um-ubd: Entrust re-queue to the upper layers
nvme-multipath: remove unused groups_only mode in ana log
nvme-multipath: fix possible io hang after ctrl reconnect
io_uring: don't touch ctx in setup after ring fd install
io_uring: Fix leaked shadow_req
One fix for PCIe users:
- Fix legacy PCI I/O port access emulation
One set of cleanups:
- Resolve most of the warnings generated by sparse across arch/riscv.
No functional changes
And one MAINTAINERS update:
- Update Palmer's E-mail address
-----BEGIN PGP SIGNATURE-----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=hkRB
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"One fix for PCIe users:
- Fix legacy PCI I/O port access emulation
One set of cleanups:
- Resolve most of the warnings generated by sparse across arch/riscv.
No functional changes
And one MAINTAINERS update:
- Update Palmer's E-mail address"
* tag 'riscv/for-v5.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
MAINTAINERS: Change to my personal email address
RISC-V: Add PCIe I/O BAR memory mapping
riscv: for C functions called only from assembly, mark with __visible
riscv: fp: add missing __user pointer annotations
riscv: add missing header file includes
riscv: mark some code and data as file-static
riscv: init: merge split string literals in preprocessor directive
riscv: add prototypes for assembly language functions from head.S
Pull parisc fix from Helge Deller:
"Fix a parisc kernel crash with ftrace functions when compiled without
frame pointers"
* 'parisc-5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix frame pointer in ftrace_regs_caller()
Jakub Kicinski says:
====================
fix BPF offload related bugs
test_offload.py catches some recently added bugs.
First of a bug in test_offload.py itself after recent changes
to netdevsim is fixed.
Second patch fixes a bug in cls_bpf, and last one addresses
a problem with the recently added XDP installation optimization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When netdevice with offloaded BPF programs is destroyed
the programs are orphaned and removed from the program
IDA - their IDs get released (the programs may remain
accessible via existing open file descriptors and pinned
files). After IDs are released they are set to 0.
This confuses dev_change_xdp_fd() because it compares
the __dev_xdp_query() result where 0 means no program
with prog->aux->id where 0 means orphaned.
dev_change_xdp_fd() would have incorrectly returned success
even though it had not installed the program.
Since drivers already catch this case via bpf_offload_dev_match()
let them handle this case. The error message drivers produce in
this case ("program loaded for a different device") is in fact
correct as the orphaned program must had to be loaded for a
different device.
Fixes: c14a9f633d ("net: Don't call XDP_SETUP_PROG when nothing is changed")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4011921137 ("net: sched: refactor block offloads counter
usage") missed the fact that either new prog or old prog may be
NULL.
Fixes: 4011921137 ("net: sched: refactor block offloads counter usage")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DebugFS for netdevsim now contains some "action trigger" files
which are write only. Don't try to capture the contents of those.
Note that we can't use os.access() because the script requires
root.
Fixes: 4418f862d6 ("netdevsim: implement support for devlink region and snapshots")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test reports EINVAL for getsockopt(SOL_SOCKET, SO_DOMAIN)
occasionally due to the uninitialized length parameter.
Initialize it to fix this, and also use int for "test_family" to comply
with the API standard.
Fixes: d6a61f80b8 ("soreuseport: test mixed v4/v6 sockets")
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Cc: Craig Gallek <cgallek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported in [0] at least one RTL8168dp version has problems
establishing a link. This chip version has an integrated RTL8211b PHY,
however the chip seems to report a wrong PHY ID, resulting in a wrong
PHY driver (for Generic Realtek PHY) being loaded.
Work around this issue by adding a hook to r8168dp_2_mdio_read()
for returning the correct PHY ID.
[0] https://bbs.archlinux.org/viewtopic.php?id=246508
Fixes: 242cd9b586 ("r8169: use phy_resume/phy_suspend")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it became possible for the DSA core to use a CPU port different
than 8, our bcm_sf2_imp_setup() function was broken because it assumes
that registers are applicable to port 8. In particular, the port's MAC
is going to stay disabled, so make sure we clear the RX_DIS and TX_DIS
bits if we are not configured for port 8.
Fixes: 9f91484f6f ("net: dsa: make "label" property optional for dsa2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink_dbg() macro does not follow dynamic debug or defined(DEBUG)
and as a result, it spams the kernel log since a PR_DEBUG level is
currently used. Fix it to be defined appropriately whether
CONFIG_DYNAMIC_DEBUG or defined(DEBUG) are set.
Fixes: 17091180b1 ("net: phylink: Add phylink_{printk, err, warn, info, dbg} macros")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synces the DMA buffer properly in order for CPU and device to see
the most up-to-data data.
Signed-off-by: Yangchun Fu <yangchun@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Historically linux tried to stick to RFC 791, 1122, 2003
for IPv4 ID field generation.
RFC 6864 made clear that no matter how hard we try,
we can not ensure unicity of IP ID within maximum
lifetime for all datagrams with a given source
address/destination address/protocol tuple.
Linux uses a per socket inet generator (inet_id), initialized
at connection startup with a XOR of 'jiffies' and other
fields that appear clear on the wire.
Thiemo Nagel pointed that this strategy is a privacy
concern as this provides 16 bits of entropy to fingerprint
devices.
Let's switch to a random starting point, this is just as
good as far as RFC 6864 is concerned and does not leak
anything critical.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Thiemo Nagel <tnagel@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-11-01
This series contains updates to e1000, igb, igc, ixgbe, i40e and driver
documentation.
Lyude Paul fixes an issue where a fatal read error occurs when the
device is unplugged from the machine. So change the read error into a
warn while the device is still present.
Manfred Rudigier found that the i350 device was not apart of the "Media
Auto Sense" feature, yet the device supports it. So add the missing
i350 device to the check and fix an issue where the media auto sense
would flip/flop when no cable was connected to the port causing spurious
kernel log messages.
I fixed an issue where the fix to resolve receive buffer starvation was
applied in more than one place in the driver, one being the incorrect
location in the i40e driver.
Wenwen Wang fixes a potential memory leak in e1000 where allocated
memory is not properly cleaned up in one of the error paths.
Jonathan Neuschäfer cleans up the driver documentation to be consistent
and remove the footnote reference, since the footnote no longer exists in
the documentation.
Igor Pylypiv cleans up a duplicate clearing of a bit, no need to clear
it twice.
v2: Fixed alignment issue in patch 3 of the series based on community
feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
__IXGBE_RX_BUILD_SKB_ENABLED bit is already cleared.
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These asterisks were once references to a line that said:
"* Other names and brands may be claimed as the property of others."
But now, they serve no purpose; they can only irritate the reader.
Fixes: de3edab427 ("e1000: update README for e1000")
Fixes: a3fb65680f ("e100.txt: Cleanup license info in kernel doc")
Fixes: da8c01c450 ("e1000e.txt: Add e1000e documentation")
Fixes: f12a84a9f6 ("Documentation: fm10k: Add kernel documentation")
Fixes: b55c52b193 ("igb.txt: Add igb documentation")
Fixes: c4e9b56e24 ("igbvf.txt: Add igbvf Documentation")
Fixes: d7064f4c19 ("Documentation/networking/: Update Intel wired LAN driver documentation")
Fixes: c4b8c01112 ("ixgbevf.txt: Update ixgbevf documentation")
Fixes: 1e06edcc2f ("Documentation: i40e: Prepare documentation for RST conversion")
Fixes: 105bf2fe6b ("i40evf: add driver to kernel build system")
Fixes: 1fae869bcf ("Documentation: ice: Prepare documentation for RST conversion")
Fixes: df69ba4321 ("ionic: Add basic framework for IONIC Network device driver")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In e1000_set_ringparam(), 'tx_old' and 'rx_old' are not deallocated if
e1000_up() fails, leading to memory leaks. Refactor the code to fix this
issue.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
