Commit Graph

48297 Commits

Author SHA1 Message Date
Jean-Jacques Hiblot
87cb12910a ARM: dts: OMAP5 / DRA7: indicate that SATA port 0 is available.
AHCI provides the register PORTS_IMPL to let the software know which port
is supported. The register must be initialized by the bootloader. However
in some cases u-boot doesn't properly initialize this value (if it is not
compiled with SATA support for example or if the SATA initialization fails).
The DTS entry "ports-implemented" can be used to override the value in
PORTS_IMPL.

Without this patch the SATA will not work in the following two cases:

* if there has been a failure to initialize SATA in u-boot.

* if ahci_platform module has been removed and re-inserted. The reason is
  that the content of PORTS_IMPL is lost after the module is removed.
  I suspect that it's because the controller is reset by the hwmod.

Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[tony@atomide.com: updated comments with what goes wrong]
Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-01-13 09:16:52 -08:00
Sekhar Nori
8e2329ead7 ARM: dts: dra72-evm-revc: fix typo in ethernet-phy node
Fix a typo in impedance setting for ethernet-phy@3

Fixes: b76db38cd8 ("ARM: dts: dra72-evm-revc: add phy impedance settings")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-01-12 13:52:21 -08:00
Peter Ujfalusi
657279778a ARM: OMAP1: DMA: Correct the number of logical channels
OMAP1510, OMAP5910 and OMAP310 have only 9 logical channels.
OMAP1610, OMAP5912, OMAP1710, OMAP730, and OMAP850 have 16 logical channels
available.

The wired 17 for the lch_count must have been used to cover the 16 + 1
dedicated LCD channel, in reality we can only use 9 or 16 channels.

The d->chan_count is not used by the omap-dma stack, so we can skip the
setup. chan_count was configured to the number of logical channels and not
the actual number of physical channels anyways.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-01-06 08:46:06 -08:00
Lokesh Vutla
6ca36a455e ARM: dts: am335x-icev2: Remove the duplicated pinmux setting
There is no mmc sd card detect on am335x-ice board. But the spi0_cs1
pin being configured as mmcsd_cd. Removing it fixes the below warning
during boot:

pinctrl-single 44e10800.pinmux: pin 44e10960.0 already
requested by 48030000.spi; cannot claim for 48060000.mmc

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[tony@atomide.com: tidied up commit message]
Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-01-05 09:30:07 -08:00
Adam Ford
a3ac350793 ARM: OMAP2+: Fix WL1283 Bluetooth Baud Rate
Commit 485fa1261f ("ARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth")
set the wrong baud rate for the UART. The Baud rate was 300,000 and it should
be 3,000,000 for WL1283.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-01-05 09:29:09 -08:00
Kishon Vijay Abraham I
1a38de8809 ARM: dts: am572x-idk: Add gpios property to control PCIE_RESETn
Add 'gpios' property to pcie1 dt node and populate it with
GPIO3_23 in order to drive PCIE_RESETn high.

This gets PCIe cards to be detected in AM572X IDK board.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-30 10:59:56 -08:00
Tony Lindgren
74de7126fc Merge branch 'omap-for-v4.10/legacy' into omap-for-v4.10/fixes 2016-12-27 10:29:24 -08:00
Markus Elfring
9a6b6f75d9 ARM: OMAP2+: PRM: Delete an error message for a failed memory allocation
Omit an extra message for a memory allocation failure in this function.

Link: http://events.linuxfoundation.org/sites/events/files/slides/LCJ16-Refactor_Strings-WSang_0.pdf
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 10:06:00 -08:00
Pali Rohár
4cf48f1d75 ARM: dts: n900: Mark eMMC slot with no-sdio and no-sd flags
Trying to initialize eMMC slot as SDIO or SD cause failure in n900 port of
qemu. eMMC itself is not detected and is not working.

Real Nokia N900 harware does not have this problem. As eMMC is really not
SDIO or SD based such change is harmless and will fix support for qemu.

Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 10:06:00 -08:00
Lokesh Vutla
1a177cf72b ARM: dts: dra72-evm-tps65917: Add voltage supplies to usb_phy, mmc, dss
Commit 5d080aa306 ("ARM: dts: dra72: Add separate dtsi for tps65917")
added a separate dtsi for dra72-evm-tps65917 moving all the voltage supplies
to this file. But it missed adding voltage supplies to usb_phy, mmc,
dss and deleted from dra72-evm-common.dtsi. Adding the voltage supply
phandles to these nodes in dra72-evm-tps65917.dtsi

Fixes: 5d080aa306 ("ARM: dts: dra72: Add separate dtsi for tps65917")
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 10:06:00 -08:00
Roger Quadros
5acd016c88 ARM: dts: am57xx-idk: Put USB2 port in peripheral mode
USB2 port can be operated in dual-role mode but till we
have dual-role support in dwc3 driver let's limit this
port to peripheral mode.

If we don't do so it defaults to host mode. USB1 port
is meant for host only operation and we don't want
both ports in host only mode.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 10:06:00 -08:00
Roger Quadros
10d27dfaf6 ARM: dts: am57xx-idk: Support VBUS detection on USB2 port
VBUS detection is available on the board via the palmas PMIC.
Use extcon-palmas driver instead of extcon-gpio-usb driver.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 10:06:00 -08:00
Milo Kim
be53e38f0d dt-bindings: mfd: Remove TPS65217 interrupts
Interrupt numbers are from the datasheet, so no need to keep them in
the ABI. Use the number in the DT file.

Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 10:06:00 -08:00
Milo Kim
30aa2e4896 ARM: dts: am335x: Fix the interrupt name of TPS65217
Use 'interrupt-names' for getting the charger interrupt number.

Fixes: 1934e89a76 ("ARM: dts: am335x: Add the charger interrupt")
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 10:06:00 -08:00
Maninder Singh
5066d5296f ARM: omap2+: fixing wrong strcat for Non-NULL terminated string
Issue caught with static analysis tool:
"Dangerous usage of 'name' (strncpy doesn't always 0-terminate it)"

Use strlcpy _includes_ the NUL terminator, and  strlcat() which ensures
that it won't overflow the buffer.

Reported-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
CC: Russell King <linux@armlinux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 10:05:47 -08:00
Grygorii Strashko
f86a2c875f ARM: omap2+: am437x: rollback to use omap3_gptimer_timer_init()
The commit 55ee7017ee ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x") unintentionally changes the
clocksource devices for AM437x from OMAP GP Timer to SyncTimer32K.

Unfortunately, the SyncTimer32K is starving from frequency deviation
as mentioned in commit 5b5c013591 ("ARM: OMAP2+: AM43x: Use gptimer
as clocksource") and, as reported by Franklin [1], even its monotonic
nature is under question (most probably there is a HW issue, but it's
still under investigation).

Taking into account above facts It's reasonable to rollback to the use
of omap3_gptimer_timer_init().

[1] http://www.spinics.net/lists/linux-omap/msg127425.html

Fixes: 55ee7017ee ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x")
Reported-by: Cooper Jr., Franklin <fcooper@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 09:38:04 -08:00
Adam Ford
7245f67f86 ARM: dts: omap3: Add DTS for Logic PD SOM-LV 37xx Dev Kit
Fixes: ("ab8dd3aed011 ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")

This adds the dts file into the Makefile. This should have been included in
the original patch.

V2:  Update patch description - same source code
V1:  Original patch

Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 09:31:25 -08:00
Javier Martinez Canillas
7f6c857b12 ARM: dts: dra7: Add an empty chosen node to top level DTSI
Commit 55871eb6e2 ("ARM: dts: dra7: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.

But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.

Fixes: 55871eb6e2 ("ARM: dts: dra7: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 09:29:16 -08:00
Javier Martinez Canillas
6ed80b3a23 ARM: dts: dm816x: Add an empty chosen node to top level DTSI
Commit 06bfb9c199 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.

But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.

Fixes: 06bfb9c199 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 09:28:51 -08:00
Javier Martinez Canillas
9536fd30d4 ARM: dts: dm814x: Add an empty chosen node to top level DTSI
Commit 76155b378c ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.

But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.

Fixes: 76155b378c ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 09:28:44 -08:00
Javier Martinez Canillas
ce95077d0c ARM: dts: am4372: Add an empty chosen node to top level DTSI
Commit 75813028bb ("ARM: dts: am4372: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.

But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.

Fixes: 75813028bb ("ARM: dts: am4372: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 09:28:04 -08:00
Javier Martinez Canillas
1d8d6d3f2f ARM: dts: am33xx: Add an empty chosen node to top level DTSI
Commit f8bf01611c ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.

But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.

Fixes: f8bf01611c ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 09:28:03 -08:00
Javier Martinez Canillas
c9faa84cb9 ARM: dts: omap5: Add an empty chosen node to top level DTSI
Commit 76a8548ea9 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.

But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.

Fixes: 76a8548ea9 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 09:28:03 -08:00
Javier Martinez Canillas
6c565d1a63 ARM: dts: omap4: Add an empty chosen node to top level DTSI
Commit da6269e7e3 ("ARM: dts: omap4: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.

But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.

Fixes: da6269e7e3 ("ARM: dts: omap4: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 09:28:02 -08:00
Javier Martinez Canillas
23ab4c6183 ARM: dts: omap3: Add an empty chosen node to top level DTSI
Commit 008a2ebcd6 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.

But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.

Fixes: 008a2ebcd6 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 09:28:02 -08:00
Javier Martinez Canillas
3d37d41a14 ARM: dts: omap2: Add an empty chosen node to top level DTSI
Commit d1f3156fc8 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.

But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.

Fixes: d1f3156fc8 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-12-27 09:28:01 -08:00
Linus Torvalds
3ddc76dfc7 Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer type cleanups from Thomas Gleixner:
 "This series does a tree wide cleanup of types related to
  timers/timekeeping.

   - Get rid of cycles_t and use a plain u64. The type is not really
     helpful and caused more confusion than clarity

   - Get rid of the ktime union. The union has become useless as we use
     the scalar nanoseconds storage unconditionally now. The 32bit
     timespec alike storage got removed due to the Y2038 limitations
     some time ago.

     That leaves the odd union access around for no reason. Clean it up.

  Both changes have been done with coccinelle and a small amount of
  manual mopping up"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  ktime: Get rid of ktime_equal()
  ktime: Cleanup ktime_set() usage
  ktime: Get rid of the union
  clocksource: Use a plain u64 instead of cycle_t
2016-12-25 14:30:04 -08:00
Linus Torvalds
b272f732f8 Merge branch 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP hotplug notifier removal from Thomas Gleixner:
 "This is the final cleanup of the hotplug notifier infrastructure. The
  series has been reintgrated in the last two days because there came a
  new driver using the old infrastructure via the SCSI tree.

  Summary:

   - convert the last leftover drivers utilizing notifiers

   - fixup for a completely broken hotplug user

   - prevent setup of already used states

   - removal of the notifiers

   - treewide cleanup of hotplug state names

   - consolidation of state space

  There is a sphinx based documentation pending, but that needs review
  from the documentation folks"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/armada-xp: Consolidate hotplug state space
  irqchip/gic: Consolidate hotplug state space
  coresight/etm3/4x: Consolidate hotplug state space
  cpu/hotplug: Cleanup state names
  cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
  staging/lustre/libcfs: Convert to hotplug state machine
  scsi/bnx2i: Convert to hotplug state machine
  scsi/bnx2fc: Convert to hotplug state machine
  cpu/hotplug: Prevent overwriting of callbacks
  x86/msr: Remove bogus cleanup from the error path
  bus: arm-ccn: Prevent hotplug callback leak
  perf/x86/intel/cstate: Prevent hotplug callback leak
  ARM/imx/mmcd: Fix broken cpu hotplug handling
  scsi: qedi: Convert to hotplug state machine
2016-12-25 14:05:56 -08:00
Thomas Gleixner
a5a1d1c291 clocksource: Use a plain u64 instead of cycle_t
There is no point in having an extra type for extra confusion. u64 is
unambiguous.

Conversion was done with the following coccinelle script:

@rem@
@@
-typedef u64 cycle_t;

@fix@
typedef cycle_t;
@@
-cycle_t
+u64

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
2016-12-25 11:04:12 +01:00
Thomas Gleixner
73c1b41e63 cpu/hotplug: Cleanup state names
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.

Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-12-25 10:47:44 +01:00
Thomas Gleixner
a051f220d6 ARM/imx/mmcd: Fix broken cpu hotplug handling
The cpu hotplug support of this perf driver is broken in several ways:

1) It adds a instance before setting up the state.

2) The state for the instance is different from the state of the
   callback. It's just a randomly chosen state.

3) The instance registration is not error checked so nobody noticed that
   the call can never succeed.

4) The state for the multi install callbacks is chosen randomly and
   overwrites existing state. This is now prevented by the core code so the
   call is guaranteed to fail.

5) The error exit path in the init function leaves the instance registered
   and then frees the memory which contains the enqueued hlist node.

6) The remove function is removing the state and not the instance.

Fix it by:

- Setting up the state before adding instances. Use a dynamically allocated
  state for it.

- Installing instances after the state has been set up

- Removing the instance in the error path before freeing memory

- Removing the instance not the state in the driver remove callback

While at is use raw_cpu_processor_id(), because cpu_processor_id() cannot
be used in preemptible context, and set the driver data after successful
registration of the pmu.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Frank Li <frank.li@nxp.com>
Cc: Zhengyu Shen <zhengyu.shen@nxp.com>
Link: http://lkml.kernel.org/r/20161221192111.596204211@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-12-25 10:47:40 +01:00
Linus Torvalds
7c0f6ba682 Replace <asm/uaccess.h> with <linux/uaccess.h> globally
This was entirely automated, using the script by Al:

  PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
  sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
        $(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)

to do the replacement at the end of the merge window.

Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-12-24 11:46:01 -08:00
Dongpo Li
48fed73ab6 ARM: dts: hix5hd2: don't change the existing compatible string
The SoC hix5hd2 compatible string has the suffix "-gmac" and
we should not change it.
We should only add the generic compatible string "hisi-gmac-v1".

Fixes: 0855950ba5 ("ARM: dts: hix5hd2: add gmac generic compatible and clock names")
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-12-20 14:12:29 -05:00
Linus Torvalds
c07dee7348 MTD updates for v4.10-rc1:
Core:
 
   * dynamic BDI object allocation (resolves some problems when built as a
     module)
   * cleanups in the ooblayout handling
 
 NAND:
 
   * new tango NAND controller driver
   * new ox820 NAND controller driver
   * addition of a new full-ID entry in the nand_ids table
   * rework of the s3c240 driver to support DT
   * extension of the nand_sdr_timings to expose tCCS, tPROG and tR
   * addition of a new flag to ask the core to wait for tCCS when sending
     a RNDIN/RNDOUT command
   * addition of a new flag to ask the core to let the controller driver
     send the READ/PROGPAGE command
 
   Minor fixes/cleanup/cosmetic changes:
   * properly support 512 ECC step size in the sunxi driver
   * improve the error messages in the PXA probe path
   * fix module autoload in the omap2 driver
   * cleanup of several nand drivers to return nand_scan{_tail}() error
     code instead of returning -EIO
   * various cleanups in the denali driver
   * fix an error check in nandsim
 
 SPI NOR:
 
   * new flash IDs
   * wait for Spansion flash to be ready after quad-enable
   * error handling fixes for Candence QSPI
   * constify some structures in Freescale QSPI driver
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJYVEDMAAoJEFySrpd9RFgtHfoP/33L6OgHn0kzonYhB3/BKFol
 WFEAdu2Z2cT9sQE0GpZFAcySasVisQMONoL0RBmvxZTeW2YtiN6NEJkr98JropzJ
 HowNDxuVuDiJ2clmTkE5J1i9WMUV0t6TqWzdbXSme9s68P6p1q9RLH6rmq06JITj
 zc56HrHgtYLCyFn5MtHPat4/jOPhqPHXfVnadtNAJ28FazhnsurkJe/ChUvGS1xJ
 2xSfueERHuPcNrpMEbNcyS4OOJpFqI1Ds3+7vJxz4kpWomAJEQ4l7Jw7e+GaKI5q
 2DsEUbvIPCMZMH1cqyWgVsWaDO820KFcJ4MwHT7nsNSvrjOEUivZCPpk/L2Wa7sd
 x6A4YvRPrKMoaE8CFgjz7K7UXDLU6Xa+ZwyIqn4YsnuunzhspjJI7BdrhApTRMwn
 Nhwr2bNmK1Hf4nfUnddH9/+0X06wOnEgzCx8I3t3VjvzbPIVozcfNVXFhLURxICR
 WRRAgbNA2ES88DFtLF2pnwIi8z+WLYRhe0tWsjb8h3/Xr8BQGS2hEy0N+MLolglj
 GlH1SMOddHHOAyG53YUNdhb3T7MbBEIcBmQH6ihJgkDqHcVrgCcaUtR2fSJII0Ln
 fpmlSBeut/KC2wIrf0+UACv2kUWpfgOQLCoKMZLjJMGytolNl63+Q/Jmrng5LjXv
 lx7sMp3dE9kBRORPeaw0
 =H2FS
 -----END PGP SIGNATURE-----

Merge tag 'for-linus-20161216' of git://git.infradead.org/linux-mtd

Pull MTD updates from Brian Norris:
 "Nothing enormous here, though notably we have some of the first work
  of a few new maintainers. I think for now I'll still be sending pull
  requests, but that's open to change in the future. Summary:

  Core:

   - dynamic BDI object allocation (resolves some problems when built as
     a module)
   - cleanups in the ooblayout handling

  NAND:

   - new tango NAND controller driver
   - new ox820 NAND controller driver
   - addition of a new full-ID entry in the nand_ids table
   - rework of the s3c240 driver to support DT
   - extension of the nand_sdr_timings to expose tCCS, tPROG and tR
   - addition of a new flag to ask the core to wait for tCCS when
     sending a RNDIN/RNDOUT command
   - addition of a new flag to ask the core to let the controller driver
     send the READ/PROGPAGE command

  Minor fixes/cleanup/cosmetic changes:

   - properly support 512 ECC step size in the sunxi driver
   - improve the error messages in the PXA probe path
   - fix module autoload in the omap2 driver
   - cleanup of several nand drivers to return nand_scan{_tail}() error
     code instead of returning -EIO
   - various cleanups in the denali driver
   - fix an error check in nandsim

  SPI NOR:

   - new flash IDs
   - wait for Spansion flash to be ready after quad-enable
   - error handling fixes for Candence QSPI
   - constify some structures in Freescale QSPI driver"

* tag 'for-linus-20161216' of git://git.infradead.org/linux-mtd: (71 commits)
  mtd: Allocate bdi objects dynamically
  mtd: nand: tango: Add standard legalese header
  mtd: maps: add missing iounmap() in error path
  mtd: spi-nor: constify fsl_qspi_devtype_data
  mtd: spi-nor: Add support for mr25h40
  mtd: spi-nor: Add support for N25Q016A
  mtd: spi-nor: Add at25df321 spi-nor flash support
  mtd: spi-nor: Fix some error codes in cqspi_setup_flash()
  mtd: spi-nor: Off by one in cqspi_setup_flash()
  mtd: spi-nor: add support for s25fl208k
  mtd: spi-nor: fix flags for s25fl128s
  mtd: spi-nor: fix spansion quad enable
  mtd: spi-nor: add Macronix mx25u25635f to list of known devices.
  mtd: mtdswap: fix spelling mistake "erassure" -> "erasure"
  mtd: bcm47xxpart: fix parsing first block after aligned TRX
  mtd: nand: tango: Use nand_to_mtd() instead of directly accessing chip->mtd
  mtd: remove unneeded initializer in mtd_ooblayout_count_bytes()
  mtd: use min_t() to refactor mtd_ooblayout_{get, set}_bytes()
  mtd: remove unneeded initializer in mtd_ooblayout_{get, set}_bytes()
  mtd: nand: nandsim: fix error check
  ...
2016-12-17 16:41:10 -08:00
Linus Torvalds
ed3c5a0be3 virtio, vhost: new device, fixes, speedups
This includes the new virtio crypto device, and fixes all over the
 place.  In particular enabling endian-ness checks for sparse builds
 found some bugs which this fixes.  And it appears that everyone is in
 agreement that disabling endian-ness sparse checks shouldn't be
 necessary any longer.
 
 So this enables them for everyone, and drops __CHECK_ENDIAN__
 and __bitwise__ APIs.
 
 IRQ handling in virtio has been refactored somewhat, the
 larger switch to IRQ_SHARED will have to wait as
 it proved too aggressive.
 
 Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
 -----BEGIN PGP SIGNATURE-----
 
 iQEcBAABAgAGBQJYUxYEAAoJECgfDbjSjVRp5lgH/22HKRyb3+M+z3oH6R9rJmz5
 T4y3XI4yDOTlh93VzxlrHjHNBnoWRvzV5hn6BKH6bTbSZ87TabNhfws11FKGvhER
 G1ipl/DvwytvvWgZ5dFdcC4x/0wpWawt2jgpEpPP33VDVkGJFEEAGj6GX10ClX99
 ggrNfzUCHOAFaIWzC29i7gYMnYHIJDUqK6ycDxZebzsE/c12SNRGASxei2D+6eYC
 YkdVg0c/d7Wsk+ZO1ugiA6omO4UdvPAVvxUkvd4YphRikwEWH7gGuz558wiSo4VN
 iEMZvyYXSEjx4B2Hg8+mH63zWROEpCmaToUix9+4AF7YhkaeX5fICNdkAPdtxc8=
 =urXH
 -----END PGP SIGNATURE-----

Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost

Pull virtio updates from Michael Tsirkin:
 "virtio, vhost: new device, fixes, speedups

  This includes the new virtio crypto device, and fixes all over the
  place. In particular enabling endian-ness checks for sparse builds
  found some bugs which this fixes. And it appears that everyone is in
  agreement that disabling endian-ness sparse checks shouldn't be
  necessary any longer.

  So this enables them for everyone, and drops the __CHECK_ENDIAN__ and
  __bitwise__ APIs.

  IRQ handling in virtio has been refactored somewhat, the larger switch
  to IRQ_SHARED will have to wait as it proved too aggressive"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (34 commits)
  Makefile: drop -D__CHECK_ENDIAN__ from cflags
  fs/logfs: drop __CHECK_ENDIAN__
  Documentation/sparse: drop __CHECK_ENDIAN__
  linux: drop __bitwise__ everywhere
  checkpatch: replace __bitwise__ with __bitwise
  Documentation/sparse: drop __bitwise__
  tools: enable endian checks for all sparse builds
  linux/types.h: enable endian checks for all sparse builds
  virtio_mmio: Set dev.release() to avoid warning
  vhost: remove unused feature bit
  virtio_ring: fix description of virtqueue_get_buf
  vhost/scsi: Remove unused but set variable
  tools/virtio: use {READ,WRITE}_ONCE() in uaccess.h
  vringh: kill off ACCESS_ONCE()
  tools/virtio: fix READ_ONCE()
  crypto: add virtio-crypto driver
  vhost: cache used event for better performance
  vsock: lookup and setup guest_cid inside vhost_vsock_lock
  virtio_pci: split vp_try_to_find_vqs into INTx and MSI-X variants
  virtio_pci: merge vp_free_vectors into vp_del_vqs
  ...
2016-12-15 18:13:41 -08:00
Linus Torvalds
66d466722c Merge branch 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:

 - an update for clkdev registration error detection to simplify users

 - add cpu capacity parsing from DT

 - support for larger cachelines found on UniPhier caches

 - documentation for udelay constants

 - properly tag assembly function declarations

 - remove unnecessary indirection of asm/mach-types.h

 - switch to syscall table based generation to simplify future additions
   of system calls, along with correpsonding commit for pkey syscalls

 - remove redundant sa1101 header file

 - RONX protect modules when they're in the vmalloc region

* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: mm: allow set_memory_*() to be used on the vmalloc region
  ARM: mm: fix set_memory_*() bounds checks
  ARM: 8631/1: clkdev: Detect errors in clk_hw_register_clkdev() for mass registration
  ARM: 8629/1: vfp: properly tag assembly function declarations in C code
  ARM: 8622/3: add sysfs cpu_capacity attribute
  ARM: 8621/3: parse cpu capacity-dmips-mhz from DT
  ARM: 8623/1: mm: add ARM_L1_CACHE_SHIFT_7 for UniPhier outer cache
  ARM: Update mach-types
  ARM: sa1100: remove SA-1101 header file
  ARM: 8619/1: udelay: document the various constants
  ARM: wire up new pkey syscalls
  ARM: convert to generated system call tables
  ARM: remove indirection of asm/mach-types.h
2016-12-15 16:06:15 -08:00
Linus Torvalds
991688bfc6 ARM: SoC driver updates for v4.10
Driver updates for ARM SoCs, including a couple of newly added drivers:
 
 - A new driver for the power management controller on TI Keystone
 - Support for the prerelease "SCPI" firmware protocol that ended up
   being shipped by Amlogic in their GXBB SoC.
 - A soc_device can now be matched using a glob from inside the
   kernel, when another driver wants to know the specific chip
   it is running on and cannot find out from DT, firmware or hardware.
 - Renesas SoCs now support identification through the soc_device
   interface, both in user space and kernel.
 - Renesas r8a7743 and r8a7745 gain support for their system controller
 - A new checking module for the ARM "PSCI" (not to be confused
   with "SCPI" mentioned above) firmware interface.
 - A new driver for the Tegra GMI memory interface
 - Support for the Tegra firmware interfaces with their
   power management controllers
 
 As usual, the updates for the reset controller framework are merged
 here, as they tend to touch multiple SoCs as well, including a new
 driver for the Oxford (now Broadcom) OX820 chip and the Tegra
 bpmp interface.
 
 The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
 Rockchips SoCs see some further updates.
 
 Conflicts:
 - ARCH_RENESAS now selects SOC_BUS, but no longer needs GPIOLIB
 - drivers/soc/renesas/Makefile: multiple files got added, keep
   all in logical sorting
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIVAwUAWFMaGWCrR//JCVInAQLs5RAA3I1I8/R+pd5jfMaAB8Od3S4g8YSqIDjC
 EIOoDPx9GDV70+cGs4ea+L9bfGs3ePGivCtcbftNsLDAueQ2jKMa3ShqxA/MMbJE
 rWQi/ARaDFY0nHL8VPWq7XyYwwrah+/gKBr8UhkaKI0vy6DBqxyCknrS2kgF88rv
 DVs2wnRvDM7GVUax0JDzuySR7BXJIuUfS78jPMESASbTQktsZTFUyH+osiqHtptD
 M5bPC8rxOeZXljt3DOvXSdK9rVnji/A3nznY4r3tlt805eaOA7CzjVSsY27WQel0
 63uj+FgE+eM0sECIxpkNbH/HHq2V4QkUoy3fk0xPkzRbllBBpS+UieGamTnPJup8
 wf5uiH1IqLLLV9F/504S92fp0pgFPpOGYWZnBDlIbh3aGq4tMjIRqRYMTyCT02hN
 +b54v0SuImFiN6p8HMS1ugYQ+1m9TU40b5pZkzkTJbSQOMm6oi3j0A0orXU/TPKd
 FVMrlUyfh+yu+vs1hGWLs1+mBjFnxXzSc8yJeaCdX4MvCY5/aVJZ+cwq4Bk+1YU5
 9Qhkeo5JV/l9FlrjxomnEq3l/WV/pFmj7JRZsb1BM88m+5LYUf2lv11b5B4FvrTd
 yx8SSpe3+ofIijdNbJ8IywF6y0OXF6UnrlouOVdSIp+wPs+pibdU/5gQep16pvqd
 WW6sVWn6quA=
 =6dP8
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "Driver updates for ARM SoCs, including a couple of newly added
  drivers:

   - A new driver for the power management controller on TI Keystone

   - Support for the prerelease "SCPI" firmware protocol that ended up
     being shipped by Amlogic in their GXBB SoC.

   - A soc_device can now be matched using a glob from inside the
     kernel, when another driver wants to know the specific chip it is
     running on and cannot find out from DT, firmware or hardware.

   - Renesas SoCs now support identification through the soc_device
     interface, both in user space and kernel.

   - Renesas r8a7743 and r8a7745 gain support for their system
     controller

   - A new checking module for the ARM "PSCI" (not to be confused with
     "SCPI" mentioned above) firmware interface.

   - A new driver for the Tegra GMI memory interface

   - Support for the Tegra firmware interfaces with their power
     management controllers

  As usual, the updates for the reset controller framework are merged
  here, as they tend to touch multiple SoCs as well, including a new
  driver for the Oxford (now Broadcom) OX820 chip and the Tegra bpmp
  interface.

  The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
  Rockchips SoCs see some further updates"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
  misc: sram: remove useless #ifdef
  drivers: psci: Allow PSCI node to be disabled
  drivers: psci: PSCI checker module
  soc: renesas: Identify SoC and register with the SoC bus
  firmware: qcom: scm: Return PTR_ERR when devm_clk_get fails
  firmware: qcom: scm: Remove core, iface and bus clocks dependency
  dt-bindings: firmware: scm: Add MSM8996 DT bindings
  memory: da8xx-ddrctl: drop the call to of_flat_dt_get_machine_name()
  bus: da8xx-mstpri: drop the call to of_flat_dt_get_machine_name()
  ARM: shmobile: Document DT bindings for Product Register
  soc: renesas: rcar-sysc: add R8A7745 support
  reset: Add Tegra BPMP reset driver
  dt-bindings: firmware: Allow child nodes inside the Tegra BPMP
  dt-bindings: Add power domains to Tegra BPMP firmware
  firmware: tegra: Add BPMP support
  firmware: tegra: Add IVC library
  dt-bindings: firmware: Add bindings for Tegra BPMP
  mailbox: tegra-hsp: Use after free in tegra_hsp_remove_doorbells()
  mailbox: Add Tegra HSP driver
  firmware: arm_scpi: add support for pre-v1.0 SCPI compatible
  ...
2016-12-15 16:03:25 -08:00
Linus Torvalds
786a72d791 ARM: DT updates for v4.10
Lots of changes as usual, so I'm trying to be brief here. Most of the
 new hardware support has the respective driver changes merged through
 other trees or has had it available for a while, so this is where things
 come together.
 
 We get a DT descriptions for a couple of new SoCs, all of them variants
 of other chips we already support, and usually coming with a new
 evaluation board:
 
 - Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
 - Qualcomm MDM9615 LTE baseband
 - NXP imx6ull, the latest and smallest i.MX6 application processor variant
 - Renesas RZ/G (r8a7743 and r8a7745) application processors
 - Rockchip PX3, a variant of the rk3188 chip used in Android tablets
 - Rockchip rk1108 single-core application processor
 - ST stm32f746 Cortex-M7 based microcontroller
 - TI DRA71x automotive processors
 
 These are commercially available consumer platforms we now support:
 - Motorola Droid 4 (xt894) mobile phone
 - Rikomagic MK808 Android TV stick based on Rockchips rx3066
 - Cloud Engines PogoPlug v3 based on OX820
 - Various Broadcom based wireless devices:
   - Netgear R8500 router
   - Tenda AC9 router
   - TP-LINK Archer C9 V1
   - Luxul XAP-1510 Access point
 - Turris Omnia open hardware router based on Armada 385
 
 And a couple of new boards targeted at developers, makers
 or industrial integration:
 - Macnica Sodia development platform for Altera socfpga (Cyclone V)
 - MicroZed board based on Xilinx Zynq FPGA platforms
 - TOPEET itop/elite based on exynos4412
 - WP8548 MangOH Open Hardware platform for IOT, based on
   Qualcomm MDM9615
 - NextThing CHIP Pro gadget
 - NanoPi M1 development board
 - AM571x-IDK industrial board based on TI AM5718
 - i.MX6SX UDOO Neo
 - Boundary Devices Nitrogen6_SOM2 (i.MX6)
 - Engicam i.CoreM6
 - Grinn i.MX6UL liteSOM/liteBoard
 - Toradex Colibri iMX6 module
 
 Other changes:
 - added peripherals on renesas, davinci, stm32f429, uniphier, sti,
   mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
   mvebu, allwinner, broadcom, exynos, zynq
 
 - Continued fixes for W=1 dtc warnings
 
 - The old STiH415/416 SoC support gets removed, these never made it into
   products and have served their purpose in the kernel as a template
   for teh newer chips from ST
 
 - The exynos4415 dtsi file is removed as nothing uses it.
 
 - Intel PXA25x can now be booted using devicetree
 
 Conflicts:
 arch/arm/boot/dts/r8a*.dtsi: a node was added
 the clk tree, keep both sides and watch out for git
 dropping the required '};' at the end of each side.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIVAwUAWFMZHGCrR//JCVInAQKQ6A/+Og42qy1rhL3cfHiSsT7e5giQNVSFY7Cm
 Z06R83AEv6HDMTNzyiJr5udRGOhm40qIoe92fhVJSRF7F6o/GbCQ7YOyU4KdQELg
 caqRCe1Nq6RT0RYU0m6xVyv/ox0JTNEaB+TcvD1x4pgUQNo9sSBfiXpTzOKhLhqs
 zmsfpNpj8v188Iofoju3WtwN26riJ7P4QdYIaNaH4qNQgoQbMbQICDwnpSsNJY+x
 MSlNrbtYqfz6vc5fqa0mtfhF6wIFxuRnTgSLi9skWZ2l/fkn4ljF3RhN1Z86TYPv
 CYsqDu+DF0YNxFrht3BAK6WTe2PdCnMNLNnMhYC6NDQ8YG1tbwvXQFM1KVanRvxx
 hXP4Nt2sZYiqA4v8joFPgp9gnyBMdhtJEtWSmHwCY0RFObySJR4I1GY7igh02HUJ
 gxlmOYcmklzLiyXvfjdDvg0sCV1tBhaBKTLYxF7lVCzG2QaR22Le+p3o+SWm+e+V
 Ruc9l/iwHaeasNnbAkDEiEyi1FobtuEeTSZnKaXfKX8WuKVZLJrCEm7WiRIsj0Ww
 vJ9ABVft7PEv/Ov3fbKBWON4vxKTBBgHuEDcbIsp19w4BSH1WJf5bGXIm7QeA3Z9
 aD+DtA5W5ExIjMQR2+qgz/BBIzVVVVvG8DEcdcCtc3JGRJll5PadShLdqKjVIerc
 SpsxqCKoRCI=
 =wJt3
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM DT updates from Arnd Bergmann:
 "Lots of changes as usual, so I'm trying to be brief here. Most of the
  new hardware support has the respective driver changes merged through
  other trees or has had it available for a while, so this is where
  things come together.

  We get a DT descriptions for a couple of new SoCs, all of them
  variants of other chips we already support, and usually coming with a
  new evaluation board:

   - Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
   - Qualcomm MDM9615 LTE baseband
   - NXP imx6ull, the latest and smallest i.MX6 application processor variant
   - Renesas RZ/G (r8a7743 and r8a7745) application processors
   - Rockchip PX3, a variant of the rk3188 chip used in Android tablets
   - Rockchip rk1108 single-core application processor
   - ST stm32f746 Cortex-M7 based microcontroller
   - TI DRA71x automotive processors

  These are commercially available consumer platforms we now support:

   - Motorola Droid 4 (xt894) mobile phone
   - Rikomagic MK808 Android TV stick based on Rockchips rx3066
   - Cloud Engines PogoPlug v3 based on OX820
   - Various Broadcom based wireless devices:
      - Netgear R8500 router
      - Tenda AC9 router
      - TP-LINK Archer C9 V1
      - Luxul XAP-1510 Access point
   - Turris Omnia open hardware router based on Armada 385

  And a couple of new boards targeted at developers, makers or
  industrial integration:

   - Macnica Sodia development platform for Altera socfpga (Cyclone V)
   - MicroZed board based on Xilinx Zynq FPGA platforms
   - TOPEET itop/elite based on exynos4412
   - WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
   - NextThing CHIP Pro gadget
   - NanoPi M1 development board
   - AM571x-IDK industrial board based on TI AM5718
   - i.MX6SX UDOO Neo
   - Boundary Devices Nitrogen6_SOM2 (i.MX6)
   - Engicam i.CoreM6
   - Grinn i.MX6UL liteSOM/liteBoard
   - Toradex Colibri iMX6 module

  Other changes:

   - added peripherals on renesas, davinci, stm32f429, uniphier, sti,
     mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
     mvebu, allwinner, broadcom, exynos, zynq

   - Continued fixes for W=1 dtc warnings

   - The old STiH415/416 SoC support gets removed, these never made it
     into products and have served their purpose in the kernel as a
     template for teh newer chips from ST

   - The exynos4415 dtsi file is removed as nothing uses it.

   - Intel PXA25x can now be booted using devicetree"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
  arm: dts: zynq: Add MicroZed board support
  ARM: dts: da850: enable high speed for mmc
  ARM: dts: da850: Add node for pullup/pulldown pinconf
  ARM: dts: da850: enable memctrl and mstpri nodes per board
  ARM: dts: da850-lcdk: Add ethernet0 alias to DT
  ARM: dts: artpec: add pcie support
  ARM: dts: add support for Turris Omnia
  devicetree: Add vendor prefix for CZ.NIC
  ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
  ARM: dts: berlin2q-marvell-dmp: fix regulators' name
  ARM: dts: Add xo to sdhc clock node on qcom platforms
  ARM: dts: r8a7794: Add device node for PRR
  ARM: dts: r8a7793: Add device node for PRR
  ARM: dts: r8a7792: Add device node for PRR
  ARM: dts: r8a7791: Add device node for PRR
  ARM: dts: r8a7790: Add device node for PRR
  ARM: dts: r8a7779: Add device node for PRR
  ARM: dts: r8a73a4: Add device node for PRR
  ARM: dts: sk-rzg1e: add Ether support
  ARM: dts: sk-rzg1e: initial device tree
  ...
2016-12-15 15:50:24 -08:00
Linus Torvalds
775fadd09e ARM: SoC defconfig updates for v4.10
Defconfig additions, removals, etc. Most of these are small changes adding
 the options for newly upstreamed drivers, or drivers needed for new board
 support.
 
 Bartlomiej Zolnierkiewicz has done a series of patches reducing the use
 of CONFIG_IDE from 19 to 3 in favor of CONFIG_ATA.
 
 Overall more patches than usual, but nothing big.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIVAwUAWFLwc2CrR//JCVInAQJeBRAApGEjTZoI/J5N6IqUIYM65bfvh/BVgfDf
 H7L8YPgP0BGy6zbj+XMyL4gsA+WRk6eWNGwMlwuOtsNkGx//hp9iFEd1ElHed/Um
 09jE7WufcKd9L9ZEexVxPV/8yjxUqWhiH99FSxbPvuoczXmzcpk4LGeSD22OYOZ7
 wODG0xAce9gvgByjHCo0AvfRJs3XZxJ0S9DigXWXHBD3Q7w8z+FOh+kbJROIUr7L
 Ik+ZpoWj8ZQ2jQsIo2NWtSRfZotT6Z3CJnqQNzkEG3jmiqXCorNtQ5QLBVdmqrKp
 8ykZaok5cCwVchFBD8SzOnempGSplPBqjrBzSwq+IhAN0yMFLZtBZeUciLjxEIjf
 aWWsGOOMSe9JiNWVQp6urCOfx4HHnq1SODlKWTJh5fbFLJl91KdqYnmfeaxg+06w
 19p6L0XVND4hErsMPaUozIITtcpNXquDzHPquSxYOc6cALM3qUlAoG8xGkPGwNP5
 UrnWgcPy56FEFejC3exO2vGHDiqMhwRviQXAqBDPUjQUXRDbTHFyRMCG6iTqMG64
 o7CVoAfzny3FUiWAdG1I6zisEDAVF1W7ctNkd3oY6cTiGpS7g3Yu+hq0FVMp7Xk8
 qx6KqK0HrH5O59l6/BsD0TgyoVH96Nql0/KoxiJr6oMCbVrBNn0BJA8I5BXAd+Zd
 gqXnf9e1Xf8=
 =2XsL
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC defconfig updates from Arnd Bergmann:
 "Defconfig additions, removals, etc. Most of these are small changes
  adding the options for newly upstreamed drivers, or drivers needed for
  new board support.

  Bartlomiej Zolnierkiewicz has done a series of patches reducing the
  use of CONFIG_IDE from 19 to 3 in favor of CONFIG_ATA.

  Overall more patches than usual, but nothing big"

* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
  ARM: davinci_all_defconfig: Enable da8xx usb otg
  ARM: defconfig: drop GPIO_SYSFS on multiplatforms
  ARM: multi_v7_defconfig: enable STMicroelectronics HVA driver
  ARM: configs: Add new config fragment to change RAM start point
  ARM: davinci_all_defconfig: Enable OHCI as module
  ARM: defconfig: turn on the DT cpufreq for Integrator
  ARM: omap2plus_defconfig: Run make savedefconfig to save some space
  ARM: davinci_all_defconfig: add missing options for systemd
  ARM: davinci_all_defconfig: enable the mstpri and ddrctl drivers
  ARM: bcm2835: add thermal driver to default config
  ARM: omap2plus_defconfig: Enable LP873X support
  ARM: omap2plus_defconfig: Enable REGULATOR_GPIO
  ARM: omap2plus_defconfig: Enable TOUCHSCREEN_TSC2004
  ARM: socfpga_defconfig: enable FS configs to support Angstrom filesystem
  ARM: config: Enable GPIO Key driver in stm32_defconfig
  ARM: tegra: Enable GMI driver in default configuration
  ARM: tegra: Enable SGTL5000 audio
  ARM: tegra: Update default configuration for v4.9-rc1
  ARM: socfpga: updates for socfpga_defconfig
  ARM: davinci_all_defconfig: enable LED default-on trigger
  ...
2016-12-15 15:41:04 -08:00
Linus Torvalds
e79ab194d1 ARM: SoC platform updates for v4.10
These are updates for platform specific code on 32-bit ARM machines,
 essentially anything that can not (yet) be expressed using DT files.
 
 Noteworthy changes include:
 
 - Added support for the TI DRA71x family of SoCs in mach-omap2,
   this is an new variant of the the DRA72x/DRA74x automotive
   infotainment chips we already supported for a while.
 
 - Added support for the ST STM32F746 SoC, the first Cortex-M7
   based microcontroller we support, related to the smaller
   STM32F4 family.
 
 - Renesas adds support for r8a7743 and r8a7745 in mach-shmobile,
   see http://elinux.org/RZ-G
 
 - SMP is now supported on the OX820 platform
 
 - A lot of code in mach-omap2 gets removed as a follow-up to
   removing support for board files in the previous release
 
 - Davinci has some new work to improve USB support
 
 - For i.MX, the performance monitor now supports profiling the
   memory controller using 'perf'
 
 Conflicts:
 arch/arm/mach-shmobile/setup-rcar-gen2.c: rcar_gen2_clocks_init()
 is gone, calling of_clk_init(NULL) is sufficient now.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIVAwUAWFMS9WCrR//JCVInAQIG+Q/7BElvubqO/Cc/VEAyoB5iF9OB9wPD2t5p
 O0KwtrTtzqJZJNGTmPiesR4DMZH07O1XoW8HqvBPeXtB7/t0tmOegwK+WABbpkSE
 ZQgUjtrIGwteJXYqU2BbhooO8G6mEsfWaqdGX8ZiIk40fPhMN6536lG+JA8DV7uv
 ckAPHCZkIf34lDtwljN97Cvj1TT9lBFp04bx7alKqfg1IMV+iMSxvSRHuuFlxRCk
 kzwVXDmFlZLmueU2KbQXTuOUrvehIGlZ/X5QWlxfrjwCwnOvr54p8WDoVWu2UkHm
 Dc8BVfsBny8mCZJRzfDD1S0PD0mWn1msdOhRb4VRzsC9DnRI4qbL0/Hstu8A7yUQ
 kBtMyVtFTzvRSclABbHHN6Mnm37AyNwSIKIB8h2U1m7YHqZGwHLaflVT5sf3tl7m
 4arTVqHtR8oSU5G5a2FTznMM2rfIx4LcCBbLQxWqzmO4Qrh4j6t7c2i7+VTfFAja
 0bToLgTArKK/cep6PWeBnMH14nzlXoKtBf2T8qwQPuAmLKy9E0ZduLKZ01B/nqrj
 OXcsnG0OUuqU4RgbIaDssRU4ohKIk8JcAl60TdRFhzj+/LTbeMaWVwbWuQS+iHd3
 zfzGUoUIhElx0vHt6ghR0BYQadszb1z9V0NEs3UM0v5cWlNodX//3okH8lZmSW6w
 +fO4dSnIKIA=
 =BF6Y
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC platform updates from Arnd Bergmann:
 "These are updates for platform specific code on 32-bit ARM machines,
  essentially anything that can not (yet) be expressed using DT files.

  Noteworthy changes include:

   - Added support for the TI DRA71x family of SoCs in mach-omap2, this
     is an new variant of the the DRA72x/DRA74x automotive infotainment
     chips we already supported for a while.

   - Added support for the ST STM32F746 SoC, the first Cortex-M7 based
     microcontroller we support, related to the smaller STM32F4 family.

   - Renesas adds support for r8a7743 and r8a7745 in mach-shmobile, see
     http://elinux.org/RZ-G

   - SMP is now supported on the OX820 platform

   - A lot of code in mach-omap2 gets removed as a follow-up to removing
     support for board files in the previous release

   - Davinci has some new work to improve USB support

   - For i.MX, the performance monitor now supports profiling the memory
     controller using 'perf'"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (95 commits)
  ARM: davinci: da830-evm: use gpio descriptor for mmc pins
  ARM: davinci: da850-evm: use gpio descriptor for mmc pins
  ARM: davinci: hawk: use gpio descriptor for mmc pins
  ARM: ARTPEC-6: add select MFD_SYSCON to MACH_ARTPEC6
  ARM: davinci: da8xx: Fix ohci device name
  ARM: oxnas: Add OX820 config and makefile entry
  ARM: oxnas: Add OX820 SMP support
  ARM: davinci: PM: fix build when da850 not compiled in
  ARM: orion5x: remove legacy support of ls-chl
  ARM: integrator: drop EBI access use syscon
  ARM: BCM5301X: Add back handler ignoring external imprecise aborts
  ARM: davinci: PM: support da8xx DT platforms
  ARM: davinci: PM: cleanup: remove references to pdata
  ARM: davinci: PM: rework init, remove platform device
  ARM: Kconfig: Introduce MACH_STM32F746 flag
  ARM: mach-stm32: Add a new SOC - STM32F746
  ARM: shmobile: document SK-RZG1E board
  ARM: shmobile: r8a7745: basic SoC support
  ARM: imx: mach-imx6ul: add imx6ull support
  ARM: zynq: Reserve correct amount of non-DMA RAM
  ...
2016-12-15 15:39:02 -08:00
Linus Torvalds
3ec5e8d82b ARM: SoC non-urgent fixes for v4.10
As usual, we queue up a few fixes that don't seem urgent enough to go in
 through -rc, or that just came a little too late given their size.
 
 The zx fixes make the platform finally boot on real hardware, the
 davinci and imx31 get the DT support working better for some of
 the machines that are still normally used with classic board files.
 One tegra fix is important for new bootloader versions, but the
 bug has been around for a while without anyone noticing.
 
 The other changes are mostly cosmetic.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIVAwUAWFLum2CrR//JCVInAQJTJhAAmLTsJE0O9akmxytLzlMsy+xhIHvXBfkx
 mCDr0sVwHFVm2vcH0bPlK4sNrjGYjIV0Qfsh4Br9NzohCxe6s8xFvPA78aYk5AZp
 kiHRv8Gap3dYTV2p6P2loeQ3o0zN7kl9/gUPOy6v4La84kUyZi9RRpyhA+HlEuwW
 loQQ6LaSVQb8dMo8Lz5GdOk4YfWyy1DSoZ1uNwD/2bqgfIDQ5MPdjwQzHeK259xE
 8WfVKtS4RXl54Psj26BfHRrH8VE8cMxfZ3eZwGykiXpOusrjNVbIEPJK8nKHuGHJ
 Ui/nAMzvCD23bsVX2JCYAKa/zRWjXqpvrHEzLJsaWq1VqtmWFS7g9wi1DjZmBBoC
 eJZI8Sg/7qL8Rkc69XSzyRUdMxdS6JfWQ6HrM/qzouja6MoRdFdbzl1WiPyYaVGd
 gBa7Lx6hQJgSWkeu0mvERdDAzjf4weeZyMFOFov0CwzMZ4VTKCR6Rk4lc8I1A/Hz
 0QcCmUj7uXC+gA6U+ZBlvDkG+e1u0Me5i+0gCCphd3UaReB5WaEriNubEwEMitci
 QI9BGIMzG974UXU9CCIwcnpFvJKSRwuZsQmPpulP1vbfIb8ajZXQ779PW5szE6qI
 h9VMtnKlDbOUEzdj6l/sCs2mWrobCr8/44cWOz7R8b31ZhBZxyJRWhIE/YvZFEvF
 Dq5OzaCNLxM=
 =i2l2
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC non-urgent fixes from Arnd Bergmann:
 "As usual, we queue up a few fixes that don't seem urgent enough to go
  in through -rc, or that just came a little too late given their size.

  The zx fixes make the platform finally boot on real hardware, the
  davinci and imx31 get the DT support working better for some of the
  machines that are still normally used with classic board files. One
  tegra fix is important for new bootloader versions, but the bug has
  been around for a while without anyone noticing.

  The other changes are mostly cosmetic"

* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
  arm64: tegra: Add missing Smaug revision
  arm64: tegra: Add VDD_GPU regulator to Jetson TX1
  arm64: dts: zte: clean up gic-v3 redistributor properties
  arm64: dts: zx: Fix gic GICR property
  bus: vexpress-config: fix device reference leak
  soc: ti: qmss: fix the case when !SMP
  ARM: lpc32xx: drop duplicate header device.h
  ARM: ixp4xx: drop duplicate header gpio.h
  ARM: socfpga: fix spelling mistake in error message
  ARM: dts: imx6q-cm-fx6: fix fec pinctrl
  ARM: dts: imx7d-pinfunc: fix UART pinmux defines
  ARM: dts: imx6qp: correct LDB clock inputs
  ARM: OMAP2+: pm-debug: Use seq_putc() in two functions
  ARM: OMAP2+: Remove the omapdss_early_init_of() function
  mfd: tps65217: Fix mismatched interrupt number
  ARM: zx: Fix error handling
  ARM: spear: Fix error handling
  ARM: davinci: da850: Fix pwm name matching
  ARM: clk: imx31: properly init clocks for machines with DT
  clk: imx31: fix rewritten input argument of mx31_clocks_init()
  ...
2016-12-15 15:15:13 -08:00
Michael S. Tsirkin
9efeccacd3 linux: drop __bitwise__ everywhere
__bitwise__ used to mean "yes, please enable sparse checks
unconditionally", but now that we dropped __CHECK_ENDIAN__
__bitwise is exactly the same.
There aren't many users, replace it by __bitwise everywhere.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Akced-by: Lee Duncan <lduncan@suse.com>
2016-12-16 00:13:41 +02:00
Linus Torvalds
e3842cbfe0 dmaengine updates for 4.10-rc1
Fairly routine update this time around with all changes specific to drivers.
 
  o New driver for STMicroelectronics FDMA
  o Memory-to-memory transfers on dw dmac
  o Support for slave maps on pl08x devices
  o Bunch of driver fixes to use dma_pool_zalloc
  o Bunch of compile and warning fixes spread across drivers
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJYUg7NAAoJEHwUBw8lI4NH5/gP/j81+2RzCUX8PiLQxNUt0Vj+
 tVJEizpWCwN1cnhc8ibZdI1DAwyj+GbN2lghYTjqqEng4yOm3czPzUl99grBrpQl
 t+Qylr9PSpck/paRhd2lgZzG8Nk+B5HJDcxBQbW4pwmbc69YAbqYzt44i4bDpR5K
 u3mBve1Ulng7peP45EZB8BA32ffCpOEAC/9SdkaPokrSv6XxxPEFvzewy+mLtioU
 a0zY0iuHqVGpOTABK65fXO/zkGiZLPXJ1T5vK7Iz8mOwuvtYVif0yktQSrx3BWbc
 9r64W7Si633wWt/C9LkuMMSmQ7nI/PyHk811cDOcxp3SA79JV5SWwdQl+5QPdtoP
 hyToaISfAY0BiNI9ltdscx3MPjlwSp08xXvi46RjSs8E2TXnbHUw+J5mTsxYuocl
 Yi61nlL5ClhCbySf9Q3GFsuAJ3O2Nq9WkCTNRIvJtrMhe3NeqDDTfBZJRD4Bfg1G
 q8RAc5oqGZDtqKHtLfwULr7Ec2Ru0hIZAyN907OwW+4jBR/eBJB1y+nGrNPtTWPT
 OOcvrxe85/+ZNROGCZKr0L8UA/MBBMZtjvMY8RMXjBE4YJbakq7tV+7l5VolKeNH
 G6I/1CC06qVPHrnetM6YejhtnmOQ4F8P1sE0wvpG0QTyHJoFq+aOhHNKJC8F9Eln
 CQM2apvL4BHvS7OHt9XL
 =Pf0d
 -----END PGP SIGNATURE-----

Merge tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma

Pull dmaengine updates from Vinod Koul:
 "Fairly routine update this time around with all changes specific to
  drivers:

   - New driver for STMicroelectronics FDMA
   - Memory-to-memory transfers on dw dmac
   - Support for slave maps on pl08x devices
   - Bunch of driver fixes to use dma_pool_zalloc
   - Bunch of compile and warning fixes spread across drivers"

[ The ST FDMA driver already came in earlier through the remoteproc tree ]

* tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
  dmaengine: sirf-dma: remove unused ‘sdesc’
  dmaengine: pl330: remove unused ‘regs’
  dmaengine: s3c24xx: remove unused ‘cdata’
  dmaengine: stm32-dma: remove unused ‘src_addr’
  dmaengine: stm32-dma: remove unused ‘dst_addr’
  dmaengine: stm32-dma: remove unused ‘sfcr’
  dmaengine: pch_dma: remove unused ‘cookie’
  dmaengine: mic_x100_dma: remove unused ‘data’
  dmaengine: img-mdc: remove unused ‘prev_phys’
  dmaengine: usb-dmac: remove unused ‘uchan’
  dmaengine: ioat: remove unused ‘res’
  dmaengine: ioat: remove unused ‘ioat_dma’
  dmaengine: ioat: remove unused ‘is_raid_device’
  dmaengine: pl330: do not generate unaligned access
  dmaengine: k3dma: move to dma_pool_zalloc
  dmaengine: at_hdmac: move to dma_pool_zalloc
  dmaengine: at_xdmac: don't restore unsaved status
  dmaengine: ioat: set error code on failures
  dmaengine: ioat: set error code on failures
  dmaengine: DW DMAC: add multi-block property to device tree
  ...
2016-12-14 20:42:45 -08:00
Linus Torvalds
a57cb1c1d7 Merge branch 'akpm' (patches from Andrew)
Merge more updates from Andrew Morton:

 - a few misc things

 - kexec updates

 - DMA-mapping updates to better support networking DMA operations

 - IPC updates

 - various MM changes to improve DAX fault handling

 - lots of radix-tree changes, mainly to the test suite. All leading up
   to reimplementing the IDA/IDR code to be a wrapper layer over the
   radix-tree. However the final trigger-pulling patch is held off for
   4.11.

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (114 commits)
  radix tree test suite: delete unused rcupdate.c
  radix tree test suite: add new tag check
  radix-tree: ensure counts are initialised
  radix tree test suite: cache recently freed objects
  radix tree test suite: add some more functionality
  idr: reduce the number of bits per level from 8 to 6
  rxrpc: abstract away knowledge of IDR internals
  tpm: use idr_find(), not idr_find_slowpath()
  idr: add ida_is_empty
  radix tree test suite: check multiorder iteration
  radix-tree: fix replacement for multiorder entries
  radix-tree: add radix_tree_split_preload()
  radix-tree: add radix_tree_split
  radix-tree: add radix_tree_join
  radix-tree: delete radix_tree_range_tag_if_tagged()
  radix-tree: delete radix_tree_locate_item()
  radix-tree: improve multiorder iterators
  btrfs: fix race in btrfs_free_dummy_fs_info()
  radix-tree: improve dump output
  radix-tree: make radix_tree_find_next_bit more useful
  ...
2016-12-14 17:25:18 -08:00
Alexander Duyck
fc1b138de7 arch/arm: add option to skip sync on DMA map and unmap
The use of DMA_ATTR_SKIP_CPU_SYNC was not consistent across all of the
DMA APIs in the arch/arm folder.  This change is meant to correct that
so that we get consistent behavior.

Link: http://lkml.kernel.org/r/20161110113424.76501.2715.stgit@ahduyck-blue-test.jf.intel.com
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-12-14 16:04:07 -08:00
Linus Torvalds
0f1d6dfe03 Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
 "Here is the crypto update for 4.10:

  API:
   - add skcipher walk interface
   - add asynchronous compression (acomp) interface
   - fix algif_aed AIO handling of zero buffer

  Algorithms:
   - fix unaligned access in poly1305
   - fix DRBG output to large buffers

  Drivers:
   - add support for iMX6UL to caam
   - fix givenc descriptors (used by IPsec) in caam
   - accelerated SHA256/SHA512 for ARM64 from OpenSSL
   - add SSE CRCT10DIF and CRC32 to ARM/ARM64
   - add AEAD support to Chelsio chcr
   - add Armada 8K support to omap-rng"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (148 commits)
  crypto: testmgr - fix overlap in chunked tests again
  crypto: arm/crc32 - accelerated support based on x86 SSE implementation
  crypto: arm64/crc32 - accelerated support based on x86 SSE implementation
  crypto: arm/crct10dif - port x86 SSE implementation to ARM
  crypto: arm64/crct10dif - port x86 SSE implementation to arm64
  crypto: testmgr - add/enhance test cases for CRC-T10DIF
  crypto: testmgr - avoid overlap in chunked tests
  crypto: chcr - checking for IS_ERR() instead of NULL
  crypto: caam - check caam_emi_slow instead of re-lookup platform
  crypto: algif_aead - fix AIO handling of zero buffer
  crypto: aes-ce - Make aes_simd_algs static
  crypto: algif_skcipher - set error code when kcalloc fails
  crypto: caam - make aamalg_desc a proper module
  crypto: caam - pass key buffers with typesafe pointers
  crypto: arm64/aes-ce-ccm - Fix AEAD decryption length
  MAINTAINERS: add crypto headers to crypto entry
  crypt: doc - remove misleading mention of async API
  crypto: doc - fix header file name
  crypto: api - fix comment typo
  crypto: skcipher - Add separate walker for AEAD decryption
  ..
2016-12-14 13:31:29 -08:00
Russell King
ed141f2890 Merge branch 'syscalls' into for-linus
Conflicts:
	arch/arm/include/asm/unistd.h
	arch/arm/include/uapi/asm/unistd.h
	arch/arm/kernel/calls.S
2016-12-14 11:14:00 +00:00
Russell King
41884629fe Merge branches 'clkdev', 'fixes', 'misc' and 'sa1100-base' into for-linus 2016-12-14 11:13:46 +00:00
Vinod Koul
4625d2a513 Merge branch 'topic/st_fdma' into for-linus 2016-12-14 09:07:07 +05:30
Vinod Koul
57fb7ee10c Merge branch 'topic/s3c64xx' into for-linus 2016-12-14 09:07:02 +05:30