Include ab8500 regulators for DB8500 SoC by default
and fix build issues
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
[Small fixup for changed boardfiles]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Try to make the regulators a little bit more useful by adding some
of the most basic consumers we're going to have in the end.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the PMU resources necessary to get perf working with
the DB5500 ASIC.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are two dividers used to derive bus clock from system clock:
system clock is divided by SCKDIV+1, then by BCKDIV+1. SCKDIV divider
has been ignored up to now, which is no problem as long as it is 0.
Take SCKDIV into account for bus clock calculation.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove double definition of ACLKUSBH, change parameter name in
root_clk_disable, as there is no reason to have a different name than
in root_clk_enable.
No functional change.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no reason why in case of PLL2 the configuration register
should be read twice, while for PLL0/1 using the value previously read
is used. Do the same for PLL2.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The calculation of the best divider value for a requested clock rate
always returned a value that was slightly too large. It was also not
protected against possible divisions by zero.
Request for very low, but non zero rates would cause the ACLK divisor
field to overflow. Catch this situation by using the maximum value.
The internal function aclk_set_rate() calculates the correct divider
value, but doesn't write it back to the register. Add the write back.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The evaluation board is driven with 1.2V core voltage, so system clock
must not exceed 192 MHz, bus clock must not exceed 110 MHz. Choose
appropriate values and set DTCMWAIT accordingly. Adapt UART setting to
avoid console log interruption and wait for the specified locking time
of 300us to pass.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If NAND is enabled we better have the include around.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some cards have the CRC errors in read on mx51 BBG board.
Configure the eSDHC pad configurations to level up the
compatibility to fix this issue.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most likely, the LCD panel on mx28 platform will require a pixel
clock higher than ref_xtal_clk (24 MHz), so the patch initializes
the parent of lcdif clock as ref_pix_clk.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This typo was fixed in 46e3f30 (mx25: fix spi device registration typo), but a
the merge at 0e44e059 (Merge commit 'v2.6.37-rc4' into imx-for-2.6.38) resolved
the merge conflict wrongly.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Update regulator names for debugfs compatiblity on SMDK6410
ARM: S3C64XX: Fix build with WM1190 disabled and WM1192 enabled on SMDK6410
ARM: S3C64XX: Reduce output of s3c64xx_dma_init1()
ARM: S3C64XX: Tone down SDHCI debugging
ARM: S3C64XX: Add clock for i2c1
ARM: S3C64XX: Staticise non-exported GPIO to interrupt functions
ARM: SAMSUNG: Include devs.h in dev-uart.c to prototype devices
ARM: S3C64XX: Fix keypad setup to configure correct number of rows
ARM: S3C2440: Fix usage gpio bank j pin definitions on GTA02
ARM: S5P64X0: Fix number of GPIO lines in Bank F
ARM: S3C2440: Select missing S3C_DEV_USB_HOST on GTA02
This patch is to add pad control helper macro to make the code easy
to read. The need is being seen when adding pad definitions for
LCDIF which gets ~30 pads to define.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes:
arch/arm/kernel/built-in.o: In function `__irq_svc':
io.c:(.text+0x2e0): undefined reference to `avic_base'
arch/arm/kernel/built-in.o: In function `__irq_usr':
io.c:(.text+0x4c8): undefined reference to `avic_base'
arch/arm/mach-mxc91231/built-in.o: In function `mxc91231_init_irq':
magx-zn5.c:(.init.text+0x18): undefined reference to `mxc_init_irq'
and was broken by
c7259df (ARM i.MX irq: Compile avic irq code only on SoCs that need it)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX3X.
Leave ARCH_MX31/35 definitions there, in case some place prevent multi-soc
single image.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX5X. Leave only places which prevent multi-soc
using ARCH_MX5X.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The boards are currently using otg_ulpi_create and mxc_ulpi_access_ops,
both are only present if CONFIG_USB_ULPI is set. To remove the need of
ifdefs in the board code introduce a imx_otg_ulpi_create functions
which expands to a static inline function if compiled without ulpi.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The platform data for the otg port is present but never used, so
remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Daniel Mack <daniel@caiaq.de>
On mx53_evk board only RX/TX pins are used on UART3.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On mx53_smd board only RX/TX pins are used on UART2.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
changes since v2:
- use v3 and v4 for specifying the ip version instead of i.MX23/28.
This is a better namespace when future versions are added.
- rename mach/fb.h to mach/mxsfb.h
changes since v1:
- Add a LCDC_ prefix to the register names.
- use set/clear registers where appropriate
- protect call to mxsfb_disable_controller() in mxsfb_remove()
with a (host->enabled) as suggested by Lothar Wassmann
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-fbdev@vger.kernel.org
While at it remove some useless consts from unsigned int arguments.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes the following warning in a mx3_defconfig build:
arch/arm/mach-mx3/mach-bug.c: In function 'bug_board_init':
arch/arm/mach-mx3/mach-bug.c:47: warning: passing argument 1 of 'mxc_iomux_setup_multiple_pins' discards qualifiers from pointer target type
While at it remove some useless consts from unsigned int arguments.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
