igb_read_phy_reg() will silently return, leaving phy_data untouched, if
hw->ops.read_reg isn't set. Depending on the uninitialized value of
phy_data, this led to the phy status check either succeeding immediately
or looping continuously for 2 seconds before emitting a noisy err-level
timeout. This message went out to the console even though there was no
actual problem.
Instead, first check if there is read_reg function pointer. If not,
proceed without trying to check the phy status register.
Fixes: b72f3f7200 ("igb: When GbE link up, wait for Remote receiver status condition")
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last caller of the stmmac_desc_ops::get_addr() callback was removed
a while ago, so remove the unused callback.
Note that the callback also only gets half the descriptor address on
systems with 64-bit descriptor addresses, so that should be fixed if it
needs to be resurrected later.
Fixes: ec222003bd ("net: stmmac: Prepare to add Split Header support")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing the pn533 device (i2c or USB), there is a logic error. The
original code first cancels the worker (flush_delayed_work) and then
destroys the workqueue (destroy_workqueue), leaving the timer the last
one to be deleted (del_timer). This result in a possible race condition
in a multi-core preempt-able kernel. That is, if the cleanup
(pn53x_common_clean) is concurrently run with the timer handler
(pn533_listen_mode_timer), the timer can queue the poll_work to the
already destroyed workqueue, causing use-after-free.
This patch reorder the cleanup: it uses the del_timer_sync to make sure
the handler is finished before the routine will destroy the workqueue.
Note that the timer cannot be activated by the worker again.
static void pn533_wq_poll(struct work_struct *work)
...
rc = pn533_send_poll_frame(dev);
if (rc)
return;
if (cur_mod->len == 0 && dev->poll_mod_count > 1)
mod_timer(&dev->listen_timer, ...);
That is, the mod_timer can be called only when pn533_send_poll_frame()
returns no error, which is impossible because the device is detaching
and the lower driver should return ENODEV code.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hw_srnprot needs to be unmapped when gamecube_rtc_read_offset_from_sram returns.
Fixs: 86559400b3 (rtc: gamecube: Add a RTC driver for the GameCube, Wii and Wii U)
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220511071354.46202-1-yuancan@huawei.com
There is no users of irqchip member in struct intel_pinctrl. Drop it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since recently, the kernel is nagging about mutable irq_chips:
"not an immutable chip, please consider fixing it!"
Drop the unneeded copy, flag it as IRQCHIP_IMMUTABLE, add the new
helper functions and call the appropriate gpiolib functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
- tighten the PCI presence check (Stefan Roese):
- fix a potential NULL pointer dereference in an error path
(Kyle Miller Smith)
- fix interpretation of the DMRSL field (Tom Yan)
- relax the data transfer alignment (Keith Busch)
- verbose error logging improvements (Max Gurtovoy, Chaitanya Kulkarni)
- misc cleanups (Chaitanya Kulkarni, me)
-----BEGIN PGP SIGNATURE-----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=w9PF
-----END PGP SIGNATURE-----
Merge tag 'nvme-5.19-2022-05-18' of git://git.infradead.org/nvme into for-5.19/drivers
Pull NVMe updates from Christoph:
"nvme updates for Linux 5.19
- tighten the PCI presence check (Stefan Roese):
- fix a potential NULL pointer dereference in an error path
(Kyle Miller Smith)
- fix interpretation of the DMRSL field (Tom Yan)
- relax the data transfer alignment (Keith Busch)
- verbose error logging improvements (Max Gurtovoy, Chaitanya Kulkarni)
- misc cleanups (Chaitanya Kulkarni, me)"
* tag 'nvme-5.19-2022-05-18' of git://git.infradead.org/nvme:
nvme: split the enum used for various register constants
nvme-fabrics: add a request timeout helper
nvme-pci: harden drive presence detect in nvme_dev_disable()
nvme-pci: fix a NULL pointer dereference in nvme_alloc_admin_tags
nvme: mark internal passthru request RQF_QUIET
nvme: remove unneeded include from constants file
nvme: add missing status values to verbose logging
nvme: set dma alignment to dword
nvme: fix interpretation of DMRSL
POLL* are unannotated values for the userspace ABI, while everything
in-kernel should use EPOLL* and the __poll_t type.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220518084005.3255380-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_file_get_normal isn't marked inline, so don't claim it as such in the
forward declaration.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220518084005.3255380-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ERR_PTR abuses the high bits of a pointer to transport error information.
This is only safe for kernel pointers and not user pointers. Fix
io_buffer_select and its helpers to just return NULL for failure and get
rid of this abuse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220518084005.3255380-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Provided buffers allow an application to supply io_uring with buffers
that can then be grabbed for a read/receive request, when the data
source is ready to deliver data. The existing scheme relies on using
IORING_OP_PROVIDE_BUFFERS to do that, but it can be difficult to use
in real world applications. It's pretty efficient if the application
is able to supply back batches of provided buffers when they have been
consumed and the application is ready to recycle them, but if
fragmentation occurs in the buffer space, it can become difficult to
supply enough buffers at the time. This hurts efficiency.
Add a register op, IORING_REGISTER_PBUF_RING, which allows an application
to setup a shared queue for each buffer group of provided buffers. The
application can then supply buffers simply by adding them to this ring,
and the kernel can consume then just as easily. The ring shares the head
with the application, the tail remains private in the kernel.
Provided buffers setup with IORING_REGISTER_PBUF_RING cannot use
IORING_OP_{PROVIDE,REMOVE}_BUFFERS for adding or removing entries to the
ring, they must use the mapped ring. Mapped provided buffer rings can
co-exist with normal provided buffers, just not within the same group ID.
To gauge overhead of the existing scheme and evaluate the mapped ring
approach, a simple NOP benchmark was written. It uses a ring of 128
entries, and submits/completes 32 at the time. 'Replenish' is how
many buffers are provided back at the time after they have been
consumed:
Test Replenish NOPs/sec
================================================================
No provided buffers NA ~30M
Provided buffers 32 ~16M
Provided buffers 1 ~10M
Ring buffers 32 ~27M
Ring buffers 1 ~27M
The ring mapped buffers perform almost as well as not using provided
buffers at all, and they don't care if you provided 1 or more back at
the same time. This means application can just replenish as they go,
rather than need to batch and compact, further reducing overhead in the
application. The NOP benchmark above doesn't need to do any compaction,
so that overhead isn't even reflected in the above test.
Co-developed-by: Dylan Yudaken <dylany@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Abstract this out from io_sqe_buffer_register() so we can use it
elsewhere too without duplicating this code.
No intended functional changes in this patch.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Obviously not really useful since it's not transferring data, but it
is helpful in benchmarking overhead of provided buffers.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_provided_buffer_select() must drop the submit lock, if needed, even
in the error handling case. Failure to do so will leave us with the
ctx->uring_lock held, causing spew like:
====================================
WARNING: iou-wrk-366/368 still has locks held!
5.18.0-rc6-00294-gdf8dc7004331 #994 Not tainted
------------------------------------
1 lock held by iou-wrk-366/368:
#0: ffff0000c72598a8 (&ctx->uring_lock){+.+.}-{3:3}, at: io_ring_submit_lock+0x20/0x48
stack backtrace:
CPU: 4 PID: 368 Comm: iou-wrk-366 Not tainted 5.18.0-rc6-00294-gdf8dc7004331 #994
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace.part.0+0xa4/0xd4
show_stack+0x14/0x5c
dump_stack_lvl+0x88/0xb0
dump_stack+0x14/0x2c
debug_check_no_locks_held+0x84/0x90
try_to_freeze.isra.0+0x18/0x44
get_signal+0x94/0x6ec
io_wqe_worker+0x1d8/0x2b4
ret_from_fork+0x10/0x20
and triggering later hangs off get_signal() because we attempt to
re-grab the lock.
Reported-by: syzbot+987d7bb19195ae45208c@syzkaller.appspotmail.com
Fixes: 149c69b04a ("io_uring: abstract out provided buffer list selection")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Create a section in MAINTAINERS for the GXP HPE architecture.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The HPE SoC is new to linux. A basic device tree layout with minimum
required for linux to boot including a timer and watchdog support has
been created.
The dts file is empty at this point but will be updated in subsequent
updates as board specific features are enabled.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Add support for HPE GXP. The GXP is based on the cortex a9 processor and
supports arm7.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Add support for the HPE GXP Timer and Watchdog. There are multiple
timers on the SoC but only one is enabled at this time.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Add support for the HPE GXP SOC timer. The GXP supports several different
kinds of timers but for the purpose of this driver there is only support
for the General Timer. The timer has a 1us resolution and is 32 bits. The
timer also creates a child watchdog device as the register region is the
same.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for the HPE GXP Watchdog. The GXP asic contains a full
complement of timers one of which is the watchdog timer. The watchdog
timer is 16 bit and has 10ms resolution. The watchdog is created as a
child device of timer since the same register range is used.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Enable HPE GXP Architecture and its watchdog for base support for HPE
GXP SoCs.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The GXP is the HPE BMC SoC that is used in the majority
of current generation HPE servers. Traditionally the asic will
last multiple generations of server before being replaced.
Info about SoC:
HPE GXP is the name of the HPE Soc. This SoC is used to implement many BMC
features at HPE. It supports ARMv7 architecture based on the Cortex A9
core. It is capable of using an AXI bus to whicha memory controller is
attached. It has multiple SPI interfaces to connect boot flash and BIOS
flash. It uses a 10/100/1000 MAC for network connectivity. It has multiple
i2c engines to drive connectivity with a host infrastructure. There
currently are no public specifications but this process is being worked.
Previously there was a requirement to reset the EHCI controller for the
asic to boot. This functionality has been moved to the u-boot
bootloader.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Mat Martineau says:
====================
mptcp: Fix checksum byte order on little-endian
These patches address a bug in the byte ordering of MPTCP checksums on
little-endian architectures. The __sum16 type is always big endian, but
was being cast to u16 and then byte-swapped (on little-endian archs)
when reading/writing the checksum field in MPTCP option headers.
MPTCP checksums are off by default, but are enabled if one or both peers
request it in the SYN/SYNACK handshake.
The corrected code is verified to interoperate between big-endian and
little-endian machines.
Patch 1 fixes the checksum byte order, patch 2 partially mitigates
interoperation with peers sending bad checksums by falling back to TCP
instead of resetting the connection.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 8684 section 3.7 describes several opportunities for a MPTCP
connection to "fall back" to regular TCP early in the connection
process, before it has been confirmed that MPTCP options can be
successfully propagated on all SYN, SYN/ACK, and data packets. If a peer
acknowledges the first received data packet with a regular TCP header
(no MPTCP options), fallback is allowed.
If the recipient of that first data packet finds a MPTCP DSS checksum
error, this provides an opportunity to fail gracefully with a TCP
fallback rather than resetting the connection (as might happen if a
checksum failure were detected later).
This commit modifies the checksum failure code to attempt fallback on
the initial subflow of a MPTCP connection, only if it's a failure in the
first data mapping. In cases where the peer initiates the connection,
requests checksums, is the first to send data, and the peer is sending
incorrect checksums (see
https://github.com/multipath-tcp/mptcp_net-next/issues/275), this allows
the connection to proceed as TCP rather than reset.
Fixes: dd8bcd1768 ("mptcp: validate the data checksum")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPTCP code typecasts the checksum value to u16 and
then converts it to big endian while storing the value into
the MPTCP option.
As a result, the wire encoding for little endian host is
wrong, and that causes interoperabilty interoperability
issues with other implementation or host with different endianness.
Address the issue writing in the packet the unmodified __sum16 value.
MPTCP checksum is disabled by default, interoperating with systems
with bad mptcp-level csum encoding should cause fallback to TCP.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/275
Fixes: c5b39e26d0 ("mptcp: send out checksum for DSS")
Fixes: 390b95a5fb ("mptcp: receive checksum for DSS")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Packham says:
====================
armada-3720-turris-mox and orion-mdio
This is a follow up to the change that converted the orion-mdio dt-binding from
txt to DT schema format. At the time I thought the binding needed
'unevaluatedProperties: false' because the core mdio.yaml binding didn't handle
the DSA switches. In reality it was simply the invalid reg property causing the
downstream nodes to be unevaluated. Fixing the reg nodes means we can set
'unevaluatedProperties: true'
Marek,
I don't know if you had a change for the reg properties in flight. I didn't see
anything on lore/lkml so sorry if this crosses with something you've done.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the binding was converted it appeared necessary to set
'unevaluatedProperties: true' because of the switch devices on the
turris-mox board. Actually the error was because of the reg property
being incorrect causing the rest of the properties to be unevaluated.
After the reg properties are fixed for turris-mox we can set
'unevaluatedProperties: false' as is generally expected.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO devices have #address-cells = <1>, #size-cells = <0>. Now that we
have a schema enforcing this for marvell,orion-mdio we can see that the
turris-mox has a unnecessary 2nd cell for the switch nodes reg property
of it's switch devices. Remove the unnecessary 2nd cell from the
switches reg property.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-05-17
This series contains updates to ice driver only.
Arkadiusz prevents writing of timestamps when rings are being
configured to resolve null pointer dereference.
Paul changes a delayed call to baseline statistics to occur immediately
which was causing misreporting of statistics due to the delay.
Michal fixes incorrect restoration of interrupt moderation settings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Ramadoss says:
====================
net: dsa: microchip: refactor the ksz switch init function
During the ksz_switch_register function, it calls the individual switches init
functions (ksz8795.c and ksz9477.c). Both these functions have few things in
common like, copying the chip specific data to struct ksz_dev, allocating
ksz_port memory and mib_names memory & cnt. And to add the new LAN937x series
switch, these allocations has to be replicated.
Based on the review feedback of LAN937x part support patch, refactored the
switch init function to move allocations to switch register.
Link:https://patchwork.kernel.org/project/netdevbpf/patch/20220504151755.11737-8-arun.ramadoss@microchip.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The name, regs_size and overrides members in struct ksz_device are
unused. Hence remove it.
And host_mask is used in only place of ksz8795.c file, which can be
replaced by dev->info->cpu_ports
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for phylink_get_caps for ksz8795 and ksz9477
series switch. It updates the struct ksz_switch_chip with the details of
the internal phys and xmii interface. Then during the get_caps based on
the bits set in the structure, corresponding phy mode is set.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mib->cnt_ptr resetting is handled in multiple places as part of
port_init_cnt(). Hence moved mib->cnt_ptr code to ksz common layer
and removed from individual product files.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz8795 and ksz9477 uses the same algorithm for copying the ethtool
strings. Hence moved to ksz_common to remove the redundant code.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz8795 and ksz9477 init function initializes the memory to dev->ports,
mib counters and assigns the ds real number of ports. Since both the
routines are same, moved the allocation of port memory to
ksz_switch_register after init.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz88xx family has one set of mib_names. The ksz87xx, ksz9477,
LAN937x based switches has one set of mib_names. In order to remove
redundant declaration, moved the struct mib_names to ksz_chip_data
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch perform the compatibility check for the device after the chip
detect is done. It is to prevent the mismatch between the device
compatible specified in the device tree and actual device found during
the detect. The ksz9477 device doesn't use any .data in the
of_device_id. But the ksz8795_spi uses .data for assigning the regmap
between 8830 family and 87xx family switch. Changed the regmap
assignment based on the chip_id from the .data.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz_chip_data in ksz8795 and ksz9477 to ksz_common.
At present, the dev->chip_id is iterated with the ksz_chip_data and then
copy its value to the ksz_dev structure. These values are declared as
constant.
Instead of copying the values and referencing it, this patch update the
dev->info to the ksz_chip_data based on the chip_id in the init
function. And also update the ksz_chip_data values for the LAN937x based
switches.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port_cnt value in the structure is not used in the switch_init.
Instead it uses the fls(chip->cpu_port), this is due to one of port in
the ksz8794 unavailable. The cpu_port for the 8794 is 0x10, fls(0x10) =
5, hence updating it directly in the ksz_chip_data structure in order to
same with all the other switches in ksz8795.c and ksz9477.c files.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2022-05-18
1) Fix "disable_policy" flag use when arriving from different devices.
From Eyal Birger.
2) Fix error handling of pfkey_broadcast in function pfkey_process.
From Jiasheng Jiang.
3) Check the encryption module availability consistency in pfkey.
From Thomas Bartschies.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of old 31 bit leftovers within ipl code:
- convert everything to pc relative code
- use 64 bit addressing mode as early as possible
- use 64 bit arithmetics wherever possible
This way the code doesn't look as odd as before anymore.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
We used to count the number of ieee80211_vifs in mvm.
This was needed for the legacy PM API, which is no longer
supported. Remove it.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220517120045.8c91ae023b15.Ia6145e4930b1d28f3fcedc316b4f177295b00557@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the firmware's life easier and always accept MCAST frames. If
needed, drop them in the driver. We need to filter out MCAST frames
in order not to have false positives in the decryption check. If we
accept MCAST frames before we have the GKT installed, we'll end up
complaining that we can't decrypt the frame.
Implement the same filtering, but in the driver.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220517120045.479956a46317.I21fac7ede9eca85a662671d694872898df884f0b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
