MPC832x does not have enough MURAM to do fixed MURAM allocation.
Change to dynamic allocation.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a low or full speed urb in progress is unlinked (or some other error
occurs), the buffer in the transaction translator (part of the hub) might end
up in an inconsistent state. This can make all further low and full speed
transactions fail, unless the buffer is cleared.
The bug can be seen when running the usbtest unlink tests as "set altsetting
to 0 failed, -110", and gets fixed by this patch.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Test the just-initialized value rather than some other one.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier x,y,f!={PTR_ERR,ERR_PTR,ERR_CAST};
statement S;
@@
x = f(...);
(
if (\(x == NULL\|IS_ERR(x)\)) S
|
*if (\(y == NULL\|IS_ERR(y)\))
{ ... when != x
return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the unused function twl6030_set_phy_clk of twl6030-usb.c.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Makes it possible to use i.e. gpio-vbus to handle vbus events.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb-interrupt is requested before the endpoints are initalised.
If an interrupt happens in the time between request_irq and the init
of the endpoint-data (as seen on the Qisda ESx00 ebook-platforms),
it is therefore possible for the interrupt handler to access endpoint-
data before its creation resulting in a null-pointer dereference.
This patch simply moves the irq request below the endpoint init.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DesignWare USB3 is a highly
configurable IP Core which can be
instantiated as Dual-Role Device (DRD),
Peripheral Only and Host Only (XHCI)
configurations.
Several other parameters can be configured
like amount of FIFO space, amount of TX and
RX endpoints, amount of Host Interrupters,
etc.
The current driver has been validated with
a virtual model of version 1.73a of that core
and with an FPGA burned with version 1.83a
of the DRD core. We have support for PCIe
bus, which is used on FPGA prototyping, and
for the OMAP5, more adaptation (or glue)
layers can be easily added and the driver
is half prepared to handle any possible
configuration the HW engineer has chosen
considering we have the information on
one of the GHWPARAMS registers to do
runtime checking of certain features.
More runtime checks can, and should, be added
in order to make this driver even more flexible
with regards to number of endpoints, FIFO sizes,
transfer types, etc.
While this supports only the device side, for
now, we will add support for Host side (xHCI -
see the updated series Sebastian has sent [1])
and OTG after we have it all stabilized.
[1] http://marc.info/?l=linux-usb&m=131341992020339&w=2
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1483) improves the ehci-hcd driver family by getting rid
of the reliance on the hcd->state variable. It has no clear owner and
it isn't protected by the usual HCD locks. In its place, the patch
adds a new, private ehci->rh_state field to record the state of the
root hub.
Along the way, the patch removes a couple of lines containing
redundant assignments to the state variable. Also, the QUIESCING
state simply gets changed to the RUNNING state, because the driver
doesn't make any distinction between them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add supprt for on-chip USB controller for Netlogic XLS MIPS64
SoC processor family.
Changes are:
- update ehci-hcd.c and ohci-hcd.c to add XLS hcds
- add ehci-xls.c: EHCI support for Netlogic XLS.
- add ohci-xls.c: OHCI support for Netlogic XLS.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These messages just clutter the log and provide no useful information to
the user, so make them pr_debug().
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1) A bug in the usage of time_after() in errata2_function().
2) Clear done_maps just prior to starting a new transfer in
start_bus_transfer(), instead of just after, when done_map bits might have
been validly set by the started transfer.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
... and some small code style fixes.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Errata 2 for the isp1760 explains that the chip sometimes does not issue
interrupts when an ATL (bulk or control) transfer is completed. There are
several issues with the current work-around (SOF interrupts) for this:
1) It seems the chip sometimes does not even set the done bit for a
completed transfer, in which case SOF interrupts does not solve
the problem since we still check the done map to find out which
transfer descriptors to handle.
2) The above point seems to happen only when ATL and SOF interrupts
are enabled at the same time. However, disabling ATL interrupts
increases the latency between transfer completion and handling.
This is very noticeable in the testusb suite, which take several
minutes more to run with ATL interrupts disabled.
This patch removes the code to switch on SOF interrupts, and instead
use a kernel timer to periodically check for "old" descriptors that
have their VALID and ACTIVE flags unset, indicating completion, thus
avoiding the dependency on the chip's done map (and SOF interrupts)
to find transfers affected by this HW bug.
[bigeasy@linutronix: 80 lines limit]
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Like the previous patch, this patch has been split from the next one
for clarity.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the few lines of code in isp1760_enable_interrupts() and
isp1760_init_maps() into isp1760_run(). This makes the following patch
easier.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From 2d487c10136f76cf3705881d34868e8592839cfe Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Tue, 12 Jul 2011 15:36:51 +0200
Subject: [PATCH] USB: ipw: convert to usb-wwan framework
This patch allows the ipw driver to use the multibuffer
infrastructure of usb-wwan. This improves speed.
Signed-off-by: Oliver Neukum<oneukum@suse.de>
Tested-by: Michal Hybner <dta081@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Scanning cannot be run during suspend or hibernation, but if
usb-stor-scan freezes another thread waiting on scanning to
complete may fail to freeze.
However, if usb-stor-scan is left freezable without ever actually
freezing then the freezer will wait on it to exit, and threads
waiting for scanning to finish will no longer be blocked. One
problem with this approach is that usb-stor-scan has a delay to
wait for devices to settle (which is currently the only point where
it can freeze). To work around this we can request that the freezer
send a fake signal when freezing, then use interruptible sleep to
wake the thread early when freezing happens.
To make this happen, the following changes are made to
usb-stor-scan:
* Use set_freezable_with_signal() instead of set_freezable() to
request a fake signal when freezing
* Use wait_event_interruptible_timeout() instead of
wait_event_freezable_timeout() to avoid freezing
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In drivers/usb/core/hub.c::usb_disconnect(), 'udev' will never be
NULL, so remove the test and printing of debug message.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the Option driver avoids binding interface 1 on Huawei K3765
and K4505 broadband modems as it should be handled by the cdc_ether
driver instead. This patch ensures we don't bind the interface 2
on those devices as that is CDC_DATA.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a NULL pointer deference. A NULL pointer
dereference happens since s5p_ehci->hcd field is not initialized
yet in probe function.
[jg1.han@samsung.com: edit commit message]
Signed-off-by: Yulgon Kim <yulgon.kim@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From EHCI Spec p.28 HC should clear PORT_SUSPEND when SW clears
PORT_RESUME. In Intel Oaktrail platform, MPH (Multi-Port Host
Controller) core clears PORT_SUSPEND directly when SW sets PORT_RESUME
bit. If we rely on PORT_SUSPEND bit to stop USB resume, we will miss
the action of clearing PORT_RESUME. This will cause unexpected long
resume signal on USB bus.
Signed-off-by: Wang Zhi <zhi.wang@windriver.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K4605 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on
demand without the intervention of usb_modeswitch. This has the benefit of
it becoming available faster and also ensures that the option driver is not
bound to a network interface that should be claimed by suitable network
driver.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K3806 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on
demand without the intervention of usb_modeswitch. This has the benefit of
it becoming available faster and also ensures that the option driver is not
bound to a network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
xhci: Handle zero-length isochronous packets.
USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth.
xhci: Remove TDs from TD lists when URBs are canceled.
xhci: Fix failed enqueue in the middle of isoch TD.
xhci: Fix memory leak during failed enqueue.
xHCI: report USB2 port in resuming as suspend
xHCI: fix port U3 status check condition
For a long time, the xHCI driver has had this note:
/* FIXME: Ignoring zero-length packets, can those happen? */
It turns out that, yes, there are drivers that need to queue zero-length
transfers for isochronous OUT transfers. Without this patch, users will
see kernel hang messages when a driver attempts to enqueue an isochronous
URB with a zero length transfer (because count_isoc_trbs_needed will return
zero for that TD, xhci_td->last_trb will never be set, and updating the
dequeue pointer will cause an infinite loop).
Matěj ran into this issue when using an NI Audio4DJ USB soundcard
with the snd-usb-caiaq driver. See
https://bugzilla.kernel.org/show_bug.cgi?id=40702
Fix count_isoc_trbs_needed() to return 1 for zero-length transfers (thanks
Alan on the math help). Update the various TRB field calculations to deal
with zero-length transfers. We're still transferring one packet with a
zero-length data payload, so the total_packet_count should be 1. The
Transfer Burst Count (TBC) and Transfer Last Burst Packet Count (TLBPC)
fields should be set to zero.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Matěj Laitl <matej@laitl.cz>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@kernel.org
usb_ifnum_to_if() can return NULL if the USB device does not have a
configuration installed (usb_device->actconfig == NULL), or if we can't
find the interface number in the installed configuration. Return an
error instead of crashing.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
In case one "forgot" to load the receiver i.e. doing
|modprobe omap2430
|modprobe musb_hdrc
he ends up with:
|musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
|HS USB OTG: no transceiver configured
|musb-hdrc musb-hdrc: musb_init_controller failed with status -19
|(NULL device *): gadget not registered.
|Unable to handle kernel NULL pointer dereference at virtual address 0000001c
|Internal error: Oops: 17 [#1] SMP
|[<c011383c>] (sysfs_find_dirent+0x4/0x60) from [<c01138c0>] (sysfs_get_dirent+0x28/0x78)
|[<c01138c0>] (sysfs_get_dirent+0x28/0x78) from [<c0115b78>] (sysfs_unmerge_group+0x1c/0x90)
|[<c0115b78>] (sysfs_unmerge_group+0x1c/0x90) from [<c0179ba4>] (dpm_sysfs_remove+0x14/0x3c)
|[<c0179ba4>] (dpm_sysfs_remove+0x14/0x3c) from [<c01742f8>] (device_del+0x40/0x1b4)
|[<c01742f8>] (device_del+0x40/0x1b4) from [<c0174478>] (device_unregister+0xc/0x18)
|[<c0174478>] (device_unregister+0xc/0x18) from [<bf0489b4>] (musb_free+0x24/0x88 [musb_hdrc])
|[<bf0489b4>] (musb_free+0x24/0x88 [musb_hdrc]) from [<bf057d18>] (musb_probe+0xb50/0xe3c [musb_hdrc])
|[<bf057d18>] (musb_probe+0xb50/0xe3c [musb_hdrc]) from [<c01779c4>] (platform_drv_probe+0x1c/0x24)
The problem is that musb_free() tries to figure out what was
initializued and what wasn't and clean up only the initialized part.
This works well for usb_del_gadget_udc() but device_unregister() can't
deal with it. Therefore we rely on the fact the we always have a parent
device and only then remove the device.
I broke this in 0f91349 ("usb: gadget: convert all users to the new udc
infrastructure")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After the prefetch/list.h restructure, drivers need to explicitly include
linux/prefetch.h in order to use the prefetch() function. Otherwise, the
current driver fails to build:
drivers/usb/musb/blackfin.c: In function 'musb_write_fifo':
drivers/usb/musb/blackfin.c:43: error: implicit declaration of function
'prefetch'
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Include dma-mapping.h to fix build of the renesas_usbhs driver
| CC drivers/usb/renesas_usbhs/mod_gadget.o
| drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_map':
| drivers/usb/renesas_usbhs/mod_gadget.c:190: error: implicit declaration of function 'dma_map_single'
| drivers/usb/renesas_usbhs/mod_gadget.c:192: error: implicit declaration of function 'dma_sync_single_for_device'
| drivers/usb/renesas_usbhs/mod_gadget.c:196: error: implicit declaration of function 'dma_mapping_error'
| drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_unmap':
| drivers/usb/renesas_usbhs/mod_gadget.c:217: error: implicit declaration of function 'dma_unmap_single'
| drivers/usb/renesas_usbhs/mod_gadget.c:219: error: implicit declaration of function 'dma_sync_single_for_cpu'
| make[5]: *** [drivers/usb/renesas_usbhs/mod_gadget.o] Error 1
| make[4]: *** [drivers/usb/renesas_usbhs] Error 2
Reported-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace DBG with dev_dbg and fix invalid access of musb->controller.
With this patch cppi_dma builds successfully.
Cc: <stable@kernel.org>
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ux500_dma.c fail to compile becase DBG has been removed from musb_debug.
Use dev_dbg for all prints.
Cc: stable@vger.kernel.org
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Mian Yousaf Kaukab<mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dma driver requires both src and dst to be set.
This fix is needed in order to run gadget mass storage.
Patch is verified on snowball.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
an 'unhandled fault' is causes when a gadget driver calls
usb_gadget_connect() while the USB cable isn't plugged into
the OTG port.
the fault is caused by an access to MUSB's memory space
while its clock is turned off due to pm_runtime kicking
in.
in order to fix the fault, we enclose musb_gadget_pullup()
with pm_runtime_get_sync() ... pm_runtime_put() calls to
be sure we will always reach that path with clock turned on.
[ balbi@ti.com : simplified commit log; removed few things
which didn't belong there ]
Cc: stable@kernel.org
Reported-by: Zach Pfeffer <zach.pfeffer@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Obviously, disabling & put regulator and iounmap(hcd->regs)
are missed in .remove and failure handling path of .probe,
so add them.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Keshava Munegowda <Keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a patch to fix an issue with the HID gadget which, at the moment,
returns STALL on a HID descriptor request. Essentially, the patch changes
the hid gadget such that a request for the HID descriptor is handled by
copying the descriptor into the response buffer, rather than falling
through the default case, in which the request is answered by a STALL.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After 622859634 (usb: musb: drop a gigantic amount of ifdeferry):
- USB_GADGET_MUSB_HDRC is no longer selectable because it
depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG
options
- The Kconfig comment still says "Enable Host or Gadget support
to see Inventra options", even though you now need to enable
both of them to see Inventra options.
Fix the dependency and drop the anyway unnecessary comment.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CC drivers/usb/musb/tusb6010_omap.o
drivers/usb/musb/tusb6010_omap.c: In function 'tusb_omap_use_shared_dmareq':
drivers/usb/musb/tusb6010_omap.c:92: error: 'musb' undeclared (first use in this function)
drivers/usb/musb/tusb6010_omap.c:92: error: (Each undeclared identifier is reported only once
drivers/usb/musb/tusb6010_omap.c:92: error: for each function it appears in.)
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For bMaxPacketSize0 we usually take what is specified in ep0->maxpacket.
This is fine in most cases, however on SuperSpeed bMaxPacketSize0
specifies the exponent instead of the actual size in bytes. The only
valid value on SS is 9 which denotes 512 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The code in this block is unused and the Author is fine with removing:
| These functions were used to debug unstable hw fifo while developing
| fusb300. It's much more stable now.
| So these functions can be removed.
Cc: "Wendy Yuan-Hsin Chen" <yhchen@faraday-tech.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_id structures need a NULL terminating
entry, add it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here is a patch for a new PID (zeitcontrol-device mifare-reader FT232BL(like FT232BM but lead free)).
Signed-off-by: Artur Zimmer <artur128@3dzimmer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A new device ID pair is added for Sierra Wireless MC8305.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a driver tries to cancel an URB, and the host controller is dying,
xhci_urb_dequeue will giveback the URB without removing the xhci_tds
that comprise that URB from the td_list or the cancelled_td_list. This
can cause a race condition between the driver calling URB dequeue and
the stop endpoint command watchdog timer.
If the timer fires on a dying host, and a driver attempts to resubmit
while the watchdog timer has dropped the xhci->lock to giveback a
cancelled URB, URBs may be given back by the xhci_urb_dequeue() function.
At that point, the URB's priv pointer will be freed and set to NULL, but
the TDs will remain on the td_list. This will cause an oops in
xhci_giveback_urb_in_irq() when the watchdog timer attempts to loop
through the endpoints' td_lists, giving back killed URBs.
Make sure that xhci_urb_dequeue() removes TDs from the TD lists and
canceled TD lists before it gives back the URB.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
When an isochronous transfer is enqueued, xhci_queue_isoc_tx_prepare()
will ensure that there is enough room on the transfer rings for all of the
isochronous TDs for that URB. However, when xhci_queue_isoc_tx() is
enqueueing individual isoc TDs, the prepare_transfer() function can fail
if the endpoint state has changed to disabled, error, or some other
unknown state.
With the current code, if Nth TD (not the first TD) fails, the ring is
left in a sorry state. The partially enqueued TDs are left on the ring,
and the first TRB of the TD is not given back to the hardware. The
enqueue pointer is left on the TRB after the last successfully enqueued
TD. This means the ring is basically useless. Any new transfers will be
enqueued after the failed TDs, which the hardware will never read because
the cycle bit indicates it does not own them. The ring will fill up with
untransferred TDs, and the endpoint will be basically unusable.
The untransferred TDs will also remain on the TD list. Since the td_list
is a FIFO, this basically means the ring handler will be waiting on TDs
that will never be completed (or worse, dereference memory that doesn't
exist any more).
Change the code to clean up the isochronous ring after a failed transfer.
If the first TD failed, simply return and allow the xhci_urb_enqueue
function to free the urb_priv. If the Nth TD failed, first remove the TDs
from the td_list. Then convert the TRBs that were enqueued into No-op
TRBs. Make sure to flip the cycle bit on all enqueued TRBs (including any
link TRBs in the middle or between TDs), but leave the cycle bit of the
first TRB (which will show software-owned) intact. Then move the ring
enqueue pointer back to the first TRB and make sure to change the
xhci_ring's cycle state to what is appropriate for that ring segment.
This ensures that the No-op TRBs will be overwritten by subsequent TDs,
and the hardware will not start executing random TRBs because the cycle
bit was left as hardware-owned.
This bug is unlikely to be hit, but it was something I noticed while
tracking down the watchdog timer issue. I verified that the fix works by
injecting some errors on the 250th isochronous URB queued, although I
could not verify that the ring is in the correct state because uvcvideo
refused to talk to the device after the first usb_submit_urb() failed.
Ring debugging shows that the ring looks correct, however.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
When the isochronous transfer support was introduced, and the xHCI driver
switched to using urb->hcpriv to store an "urb_priv" pointer, a couple of
memory leaks were introduced into the URB enqueue function in its error
handling paths.
xhci_urb_enqueue allocates urb_priv, but it doesn't free it if changing
the control endpoint's max packet size fails or the bulk endpoint is in
the middle of allocating or deallocating streams.
xhci_urb_enqueue also doesn't free urb_priv if any of the four endpoint
types' enqueue functions fail. Instead, it expects those functions to
free urb_priv if an error occurs. However, the bulk, control, and
interrupt enqueue functions do not free urb_priv if the endpoint ring is
NULL. It will, however, get freed if prepare_transfer() fails in those
enqueue functions.
Several of the error paths in the isochronous endpoint enqueue function
also fail to free it. xhci_queue_isoc_tx_prepare() doesn't free urb_priv
if prepare_ring() indicates there is not enough room for all the
isochronous TDs in this URB. If individual isochronous TDs fail to be
queued (perhaps due to an endpoint state change), urb_priv is also leaked.
This argues that the freeing of urb_priv should be done in the function
that allocated it, xhci_urb_enqueue.
This patch looks rather ugly, but refactoring the code will have to wait
because this patch needs to be backported to stable kernels.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
When a USB2 port initiate a remote wakeup, software shall ensure that
resume is signaled for at least 20ms, and then write '0' to the PLS field.
According to this, xhci driver do the following things:
1. When receive a remote wakeup event in irq_handler, set the resume_done
value as jiffies + 20ms, and modify rh_timer to poll root hub status at
that time;
2. When receive a GetPortStatus request, if the jiffies is after the
resume_done value, clear the resume signal and resume_done.
However, if usb_port_resume() is called before the rh_timer triggered, it
will indicate the port as Suspend Cleared and skip the clear resume signal
part. The device will fail the usb_get_status request in finish_port_resume(),
and usbcore will try a reset-resume instead. Device will work OK after
reset-resume, but resume_done value is not cleared in this case, and
xhci_bus_suspend() will fail because when it finds a non-zero resume_done
value, it will regard the port as resuming and return -EBUSY.
This causes issue on some platforms that the system fail to suspend
after remote wakeup from suspend by USB2 devices connected to xHCI port.
To fix this issue, report the port status as suspend if the resume is
signaling less that 20ms, and usb_port_resume() will wait 25ms and check
port status again, so xHCI driver can clear the resume signaling and
resume_done value.
This should be backported to kernels as old as 2.6.37.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Fix the port U3 status check when Clear PORT_SUSPEND Feature.
The port status should be masked with PORT_PLS_MASK to check if it's in
U3 state.
This should be backported to kernels as old as 2.6.37.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
A new device ID pair is added for Qualcomm Modem present in Sagemcom's HiLo3G module.
Signed-off-by: Vijay Chavan <VijayChavan007@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ehci_bios_handoff() is marked __devinit, `ehci_dmi_nohandoff_table' should be
marked __devinitconst, not __initconst. This fixes the following section
mismatch:
WARNING: vmlinux.o(.devinit.text+0x4f08): Section mismatch in reference from the function ehci_bios_handoff() to the variable .init.rodata:ehci_dmi_nohandoff_table
The function __devinit ehci_bios_handoff() references a variable __initconst ehci_dmi_nohandoff_table.
If ehci_dmi_nohandoff_table is only used by ehci_bios_handoff then annotate ehci_dmi_nohandoff_table with a matching annotation.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K4511 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K4510 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K3771 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K3770 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the recent addition of the FT232H showed that baudrate was set wrong. See
gmane.linux.usb.general: "[ftdi_sio] FT232H support". With the old code,
the MSB of the 4 encoded fractional divider bits and more important the
clock predivider bits got lost. Adding the FT232H to the code patch were
these bits are shifted solves the problem. I verified baud rates with a
scope now.
I suspect, that the BM device probably needs these bits shifted too. But
there is no predivider bit, so this is not obvious, and a missing MSB of the
encoded fractional divider only shifts the resulting baudrate minimal.
The AM has only 3 bits of encoded fractional divider, so it is not impacted.
I have no BM device to test, so I only added a comment and left the code for
the BM untouched.
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The sequence to put port in test mode is not complete.
According EHCI specification all enabled ports must be
put in suspend.
Signed-off-by: Boris Todorov <boris.st.todorov@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Even if it's unlikely for this to cause an error,
there is a typo in the code that uses the bitwise-AND
operator instead of the logical one.
Signed-off-by: Ionut Nicu <ionut.nicu@cloudbit.ro>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Connecting the V2M to a Linux host results in a constant stream of
errors spammed to the console, all of the form
sd 1:0:0:0: ioctl_internal_command return code = 8070000
: Sense Key : 0x4 [current]
: ASC=0x0 ASCQ=0x0
The errors appear to be otherwise harmless. Add an unusual_devs entry
which eliminates all of the error messages.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As cpu_is_mx stuff is being used in the driver, header mach/hardware.h
should be explicitly included.
The missing of the header is causing today's linux-next build error
as bleow.
CC drivers/usb/host/ehci-hcd.o
In file included from linux-next/drivers/usb/host/ehci-hcd.c:1190:0:
linux-next/drivers/usb/host/ehci-mxc.c: In function 'ehci_mxc_drv_probe':
linux-next/drivers/usb/host/ehci-mxc.c:175:2: error: implicit declaration of function 'cpu_is_mx35'
linux-next/drivers/usb/host/ehci-mxc.c:175:2: error: implicit declaration of function 'cpu_is_mx25'
linux-next/drivers/usb/host/ehci-mxc.c:185:2: error: implicit declaration of function 'cpu_is_mx51'
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Assign operator instead of equality test in the usbtmc_ioctl_abort_bulk_in() function.
Signed-off-by: Maxim A. Nikulin <M.A.Nikulin@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1st pos of __usbhsg_for_each_uep() was wrong.
Expected uep were ep1, ep2, ep3...
but each uep were ep0, ep2, ep3 ...
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Include dma-mapping.h to fix build of the renesas_usbhs driver
CC drivers/usb/renesas_usbhs/mod_gadget.o
drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_map':
drivers/usb/renesas_usbhs/mod_gadget.c:190: error: implicit declaration of function 'dma_map_single'
drivers/usb/renesas_usbhs/mod_gadget.c:192: error: implicit declaration of function 'dma_sync_single_for_device'
drivers/usb/renesas_usbhs/mod_gadget.c:196: error: implicit declaration of function 'dma_mapping_error'
drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_unmap':
drivers/usb/renesas_usbhs/mod_gadget.c:217: error: implicit declaration of function 'dma_unmap_single'
drivers/usb/renesas_usbhs/mod_gadget.c:219: error: implicit declaration of function 'dma_sync_single_for_cpu'
make[5]: *** [drivers/usb/renesas_usbhs/mod_gadget.o] Error 1
make[4]: *** [drivers/usb/renesas_usbhs] Error 2
Reported-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
<linux/irq.h> states:
* Please do not include this file in generic code. There is currently
* no requirement for any architecture to implement anything held
* within this file.
prefetch() and prefetchw() need <linux/prefetch.h> on m68k:
drivers/usb/gadget/net2272.c: In function ‘net2272_write_fifo’:
drivers/usb/gadget/net2272.c:468: error: implicit declaration of function ‘prefetch’
drivers/usb/gadget/net2272.c: In function ‘net2272_read_fifo’:
drivers/usb/gadget/net2272.c:574: error: implicit declaration of function ‘prefetchw’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
usb/config: use proper endian access for wMaxPacketSize
USB: xhci: fix OS want to own HC
xhci: Don't submit commands or URBs to halted hosts.
an 'unhandled fault' is causes when a gadget driver calls
usb_gadget_connect() while the USB cable isn't plugged into
the OTG port.
the fault is caused by an access to MUSB's memory space
while its clock is turned off due to pm_runtime kicking
in.
in order to fix the fault, we enclose musb_gadget_pullup()
with pm_runtime_get_sync() ... pm_runtime_put() calls to
be sure we will always reach that path with clock turned on.
[ balbi@ti.com : simplified commit log; removed few things
which didn't belong there ]
Cc: stable@kernel.org
Reported-by: Zach Pfeffer <zach.pfeffer@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Obviously, disabling & put regulator and iounmap(hcd->regs)
are missed in .remove and failure handling path of .probe,
so add them.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Keshava Munegowda <Keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a patch to fix an issue with the HID gadget which, at the moment,
returns STALL on a HID descriptor request. Essentially, the patch changes
the hid gadget such that a request for the HID descriptor is handled by
copying the descriptor into the response buffer, rather than falling
through the default case, in which the request is answered by a STALL.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After 622859634 (usb: musb: drop a gigantic amount of ifdeferry):
- USB_GADGET_MUSB_HDRC is no longer selectable because it
depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG
options
- The Kconfig comment still says "Enable Host or Gadget support
to see Inventra options", even though you now need to enable
both of them to see Inventra options.
Fix the dependency and drop the anyway unnecessary comment.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CC drivers/usb/musb/tusb6010_omap.o
drivers/usb/musb/tusb6010_omap.c: In function 'tusb_omap_use_shared_dmareq':
drivers/usb/musb/tusb6010_omap.c:92: error: 'musb' undeclared (first use in this function)
drivers/usb/musb/tusb6010_omap.c:92: error: (Each undeclared identifier is reported only once
drivers/usb/musb/tusb6010_omap.c:92: error: for each function it appears in.)
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For bMaxPacketSize0 we usually take what is specified in ep0->maxpacket.
This is fine in most cases, however on SuperSpeed bMaxPacketSize0
specifies the exponent instead of the actual size in bytes. The only
valid value on SS is 9 which denotes 512 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The code in this block is unused and the Author is fine with removing:
| These functions were used to debug unstable hw fifo while developing
| fusb300. It's much more stable now.
| So these functions can be removed.
Cc: "Wendy Yuan-Hsin Chen" <yhchen@faraday-tech.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_id structures need a NULL terminating
entry, add it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
wMaxPacketSize is __le16 and should be accessed as such. Also fix the
wBytesPerInterval assignment while here.
v2: also fix the wBytesPerInterval assigment, noticed by Matt Evans
This patch should be backported to the 3.0 kernel.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Matt Evans <matt@ozlabs.org>
Cc: stable@kernel.org
Software should set XHCI_HC_OS_OWNED bit to request ownership of xHC.
This patch should be backported to kernels as far back as 2.6.31.
Signed-off-by: JiSheng Zhang <jszhang3@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Commit fccf4e8620
"USB: Free bandwidth when usb_disable_device is called" caused a bit of an
issue when the xHCI host controller driver is unloaded. It changed the
USB core to remove all endpoints when a USB device is disabled. When the
driver is unloaded, it will remove the SuperSpeed split root hub, which
will disable all devices under that roothub and then halt the host
controller. When the second High Speed split roothub is removed, the USB
core will attempt to disable the endpoints, which will submit a Configure
Endpoint command to a halted host controller.
The command will eventually time out, but it makes the xHCI driver unload
take *minutes* if there are a couple of USB 1.1/2.0 devices attached. We
must halt the host controller when the SuperSpeed roothub is removed,
because we can't allow any interrupts from things like port status
changes.
Make several different functions not submit commands or URBs to the host
controller when the host is halted, by adding a check in
xhci_check_args(). xhci_check_args() is used by these functions:
xhci.c-int xhci_urb_enqueue()
xhci.c-int xhci_drop_endpoint()
xhci.c-int xhci_add_endpoint()
xhci.c-int xhci_check_bandwidth()
xhci.c-void xhci_reset_bandwidth()
xhci.c-static int xhci_check_streams_endpoint()
xhci.c-int xhci_discover_or_reset_device()
It's also used by xhci_free_dev(). However, we have to take special
care in that case, because we want the device memory to be freed if the
host controller is halted.
This patch should be backported to the 2.6.39 and 3.0 kernel.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
The driver had to decide how many events to allocate when the v4l2_fh struct
was created. It was possible to add more events afterwards, but there was no
way to ensure that you wouldn't miss important events if the event queue
would fill up for that filehandle.
In addition, once there were no more free events, any new events were simply
dropped on the floor.
For the control event in particular this made life very difficult since
control status/value changes could just be missed if the number of allocated
events and the speed at which the application read events was too low to keep
up with the number of generated events. The application would have no idea
what the latest state was for a control since it could have missed the latest
control change.
So this patch makes some major changes in how events are allocated. Instead
of allocating events per-filehandle they are now allocated when subscribing an
event. So for that particular event type N events (determined by the driver)
are allocated. Those events are reserved for that particular event type.
This ensures that you will not miss events for a particular type altogether.
In addition, if there are N events in use and a new event is raised, then
the oldest event is dropped and the new one is added. So the latest event
is always available.
This can be further improved by adding the ability to merge the state of
two events together, ensuring that no data is lost at all. This will be
added in the next patch.
This also makes it possible to allow the user to determine the number of
events that will be allocated. This is not implemented at the moment, but
would be trivial.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that supported events used to be rare, but now that controls can also
raise events this will become much more common since almost all drivers have
controls.
This means that keeping struct v4l2_events as a separate struct make no more
sense. Merging it into struct v4l2_fh simplifies things substantially as it
is now an integral part of the filehandle struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix build issue caused by undefined struct scatterlist in
drivers/usb/renesas_usbhs/fifo.c.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (741 commits)
staging:iio:meter:ade7753 should be 16 bit read not 8 bit for mode register.
staging:iio:kfifo_buf fix double initialization of the ring device structure.
staging:iio:accel:lis3l02dq: fix incorrect pointer passed to spi_set_drvdata.
staging:iio:imu fix missing register table index for some channels
spectra: enable device before poking it
staging: rts_pstor: Fix a miswriting
staging/lirc_bt829: Return -ENODEV when no hardware is found.
staging/lirc_parallel: remove pointless prototypes.
staging/lirc_parallel: fix panic on rmmod
staging:iio:adc:ad7476: Incorrect pointer into spi_set_drvdata.
Staging: zram: Fix kunmapping order
Revert "gma500: Fix dependencies"
gma500: Add medfield header
gma500: wire up the mrst i2c bus from chip_info
gma500: Fix DPU build
gma500: Clean up the DPU config and make it runtime
gma500: resync with Medfield progress
gma500: Use the mrst helpers and power control for mode commit
gma500@ Fix backlight range error
gma500: More Moorestown muddle meddling means MM maybe might modeset
...
Fix up fairly trivial conflicts all over, mostly due to header file
cleanup conflicts, but some deleted files and some just context changes:
- Documentation/feature-removal-schedule.txt
- drivers/staging/bcm/headers.h
- drivers/staging/brcm80211/brcmfmac/dhd_linux.c
- drivers/staging/brcm80211/brcmfmac/dhd_sdio.c
- drivers/staging/brcm80211/brcmfmac/wl_cfg80211.h
- drivers/staging/brcm80211/brcmfmac/wl_iw.c
- drivers/staging/et131x/et131x_netdev.c
- drivers/staging/rtl8187se/ieee80211/ieee80211_softmac.c
- drivers/staging/rtl8192e/r8192E.h
- drivers/staging/usbip/userspace/src/utils.h
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (115 commits)
EHCI: fix direction handling for interrupt data toggles
USB: serial: add IDs for WinChipHead USB->RS232 adapter
USB: OHCI: fix another regression for NVIDIA controllers
usb: gadget: m66592-udc: add pullup function
usb: gadget: m66592-udc: add function for external controller
usb: gadget: r8a66597-udc: add pullup function
usb: renesas_usbhs: support multi driver
usb: renesas_usbhs: inaccessible pipe is not an error
usb: renesas_usbhs: care buff alignment when dma handler
USB: PL2303: correctly handle baudrates above 115200
usb: r8a66597-hcd: fixup USB_PORT_STAT_C_SUSPEND shift
usb: renesas_usbhs: compile/config are rescued
usb: renesas_usbhs: fixup comment-out
usb: update email address in ohci-sh and r8a66597-hcd
usb: r8a66597-hcd: add function for external controller
EHCI: only power off port if over-current is active
USB: mon: Allow to use usbmon without debugfs
USB: EHCI: go back to using the system clock for QH unlinks
ehci: add pci quirk for Ordissimo and RM Slate 100 too
ehci: refactor pci quirk to use standard dmi_check_system method
...
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
isofs: Remove global fs lock
jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
mm/truncate.c: fix build for CONFIG_BLOCK not enabled
fs:update the NOTE of the file_operations structure
Remove dead code in dget_parent()
AFS: Fix silly characters in a comment
switch d_add_ci() to d_splice_alias() in "found negative" case as well
simplify gfs2_lookup()
jfs_lookup(): don't bother with . or ..
get rid of useless dget_parent() in btrfs rename() and link()
get rid of useless dget_parent() in fs/btrfs/ioctl.c
fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
drivers: fix up various ->llseek() implementations
fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
Ext4: handle SEEK_HOLE/SEEK_DATA generically
Btrfs: implement our own ->llseek
fs: add SEEK_HOLE and SEEK_DATA flags
reiserfs: make reiserfs default to barrier=flush
...
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
All these are instances of
#define NAME value;
or
#define NAME(params_opt) value;
These of course fail to build when used in contexts like
if(foo $OP NAME)
while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
foo = NAME + 1; /* foo = value; + 1; */
bar = NAME - 1; /* bar = value; - 1; */
baz = NAME & quux; /* baz = value; & quux; */
Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.
There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Btrfs needs to be able to control how filemap_write_and_wait_range() is called
in fsync to make it less of a painful operation, so push down taking i_mutex and
the calling of filemap_write_and_wait() down into the ->fsync() handlers. Some
file systems can drop taking the i_mutex altogether it seems, like ext3 and
ocfs2. For correctness sake I just pushed everything down in all cases to make
sure that we keep the current behavior the same for everybody, and then each
individual fs maintainer can make up their mind about what to do from there.
Thanks,
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch (as1480) fixes a rather obscure bug in ehci-hcd. The
qh_update() routine needs to know the number and direction of the
endpoint corresponding to its QH argument. The number can be taken
directly from the QH data structure, but the direction isn't stored
there. The direction is taken instead from the first qTD linked to
the QH.
However, it turns out that for interrupt transfers, qh_update() gets
called before the qTDs are linked to the QH. As a result, qh_update()
computes a bogus direction value, which messes up the endpoint toggle
handling. Under the right combination of circumstances this causes
usb_reset_endpoint() not to work correctly, which causes packets to be
dropped and communications to fail.
Now, it's silly for the QH structure not to have direct access to all
the descriptor information for the corresponding endpoint. Ultimately
it may get a pointer to the usb_host_endpoint structure; for now,
adding a copy of the direction flag solves the immediate problem.
This allows the Spyder2 color-calibration system (a low-speed USB
device that sends all its interrupt data packets with the toggle set
to 0 and hance requires constant use of usb_reset_endpoint) to work
when connected through a high-speed hub. Thanks to Graeme Gill for
supplying the hardware that allowed me to track down this bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Graeme Gill <graeme@argyllcms.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ID 4348:5523 for WinChipHead USB->RS 232 adapter with
Prolifec PL2303 chipset
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The NVIDIA series of OHCI controllers continues to be troublesome. A
few people using the MCP67 chipset have reported that even with the
most recent kernels, the OHCI controller fails to handle new
connections and spams the system log with "unable to enumerate USB
port" messages. This is different from the other problems previously
reported for NVIDIA OHCI controllers, although it is probably related.
It turns out that the MCP67 controller does not like to be kept in the
RESET state very long. After only a few seconds, it decides not to
work any more. This patch (as1479) changes the PCI initialization
quirk code so that NVIDIA controllers are switched into the SUSPEND
state after 50 ms of RESET. With no interrupts enabled and all the
downstream devices reset, and thus unable to send wakeup requests,
this should be perfectly safe (even for non-NVIDIA hardware).
The removal code in ohci-hcd hasn't been changed; it will still leave
the controller in the RESET state. As a result, if someone unloads
ohci-hcd and then reloads it, the controller won't work again until
the system is rebooted. If anybody complains about this, the removal
code can be updated similarly.
This fixes Bugzilla #22052.
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
M66592 has the pin of WR0 and WR1. So, if one write-pin of CPU
connects to the pins, we have to change the setting of FIFOSEL
register in the controller. If we don't change the setting,
the controller cannot send the data of odd length.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some SuperH/board has multi USBHS on it.
This patch supports multi register for renesas_usbhs
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is typo fix of
749da5f8 (USB: straighten out port feature vs. port status usage)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch rescues renesas_usbhs compile from
commit 193ab2a (usb: gadget: allow multiple gadgets to be built)
CONFIG_USB_RENESAS_USBHS compile renesas_usbhs main code which
is shared between Host/Gadget.
CONFIG_USB_RENESAS_USBHS_UDC add mod_gadget to it.
It had lost USB_GADGET_DUALSPEED
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch add/modify comment-out of renesas_usbhs.
On this process, usbhs_pkt_init was moved because it was placed under
usbhsf_null_handler which has no relationship it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
R8A66597 has the pin of WR0 and WR1. So, if one write-pin of CPU
connects to the pins, we have to change the setting of FIFOSEL
register in the controller. If we don't change the setting,
the controller cannot send the data of odd length.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MAX4967 USB power supply chip we use on our boards signals over-current when
power is not enabled; once it's enabled, over-current signal returns to normal.
That unfortunately caused the endless stream of "over-current change on port"
messages. The EHCI root hub code reacts on every over-current signal change
with powering off the port -- such change event is generated the moment the
port power is enabled, so once enabled the power is immediately cut off.
I think we should only cut off power when we're seeing the active over-current
signal, so I'm adding such check to that code. I also think that the fact that
we've cut off the port power should be reflected in the result of GetPortStatus
request immediately, hence I'm adding a PORTSCn register readback after write...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do not bail out with an error in mon_text_init() if debugfs is not
available, instead just return 0 and let mon_init() go ahead with
loading the binary API. Return -ENOMEM in case debugfs_create_dir()
fails for other reasons. Later, it is enough to check for mon_dir
not set.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1477) fixes a problem affecting a few types of EHCI
controller. Contrary to what one might expect, these controllers
automatically stop their internal frame counter when no ports are
enabled. Since ehci-hcd currently relies on the frame counter for
determining when it should unlink QHs from the async schedule, those
controllers run into trouble: The frame counter stops and the QHs
never get unlinked.
Some systems have also experienced other problems traced back to
commit b963801164 (USB: ehci-hcd unlink
speedups), which made the original switch from using the system clock
to using the frame counter. It never became clear what the reason was
for these problems, but evidently it is related to use of the frame
counter.
To fix all these problems, this patch more or less reverts that commit
and goes back to using the system clock. But this can't be done
cleanly because other changes have since been made to the scan_async()
subroutine. One of these changes involved the tricky logic that tries
to avoid rescanning QHs that have already been seen when the scanning
loop is restarted, which happens whenever an URB is given back.
Switching back to clock-based unlinks would make this logic even more
complicated.
Therefore the new code doesn't rescan the entire async list whenever a
giveback occurs. Instead it rescans only the current QH and continues
on from there. This requires the use of a separate pointer to keep
track of the next QH to scan, since the current QH may be unlinked
while the scanning is in progress. That new pointer must be global,
so that it can be adjusted forward whenever the _next_ QH gets
unlinked. (uhci-hcd uses this same trick.)
Simplification of the scanning loop removes a level of indentation,
which accounts for the size of the patch. The amount of code changed
is relatively small, and it isn't exactly a reversion of the
b963801164 commit.
This fixes Bugzilla #32432.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Tested-by: Matej Kenda <matejken@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add another variant of the Pegatron tablet used by Ordissimo, and
apparently RM Slate 100, to the list of models that should skip the
negociation for the handoff of the EHCI controller.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit 3610ea5397 (ehci: workaround for pci
quirk timeout on ExoPC), a workaround was added to skip the negociation for
the handoff of the EHCI controller.
Refactor the DMI detection code to use standard dmi_check_system function.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are cases, when 80% max isochronous bandwidth is too limiting.
For example I have two USB video capture cards which stream uncompressed
video, and to stream full NTSC + PAL videos we'd need
NTSC 640x480 YUV422 @30fps ~17.6 MB/s
PAL 720x576 YUV422 @25fps ~19.7 MB/s
isoc bandwidth.
Now, due to limited alt settings in capture devices NTSC one ends up
streaming with max_pkt_size=2688 and PAL with max_pkt_size=2892, both
with interval=1. In terms of microframe time allocation this gives
NTSC ~53us
PAL ~57us
and together
~110us > 100us == 80% of 125us uframe time.
So those two devices can't work together simultaneously because the'd
over allocate isochronous bandwidth.
80% seemed a bit arbitrary to me, and I've tried to raise it to 90% and
both devices started to work together, so I though sometimes it would be
a good idea for users to override hardcoded default of max 80% isoc
bandwidth.
After all, isn't it a user who should decide how to load the bus? If I
can live with 10% or even 5% bulk bandwidth that should be ok. I'm a USB
newcomer, but that 80% set in stone by USB 2.0 specification seems to be
chosen pretty arbitrary to me, just to serve as a reasonable default.
NOTE 1
~~~~~~
for two streams with max_pkt_size=3072 (worst case) both time
allocation would be 60us+60us=120us which is 96% periodic bandwidth
leaving 4% for bulk and control. Alan Stern suggested that bulk then
would be problematic (less than 300*8 bittimes left per microframe), but
I think that is still enough for control traffic.
NOTE 2
~~~~~~
Sarah Sharp expressed concern that maxing out periodic bandwidth
could lead to vendor-specific hardware bugs on host controllers, because
> It's entirely possible that you'll run into
> vendor-specific bugs if you try to pack the schedule with isochronous
> transfers. I don't think any hardware designer would seriously test or
> validate their hardware with a schedule that is basically a violation of
> the USB bus spec (more than 80% for periodic transfers).
So far I've only tested this patch on my HP Mini 5103 with N10 chipset
kirr@mini:~$ lspci
00:00.0 Host bridge: Intel Corporation N10 Family DMI Bridge
00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller
00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02)
00:1c.3 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 4 (rev 02)
00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation N10/ICH7 Family SATA AHCI Controller (rev 02)
01:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8059 PCI-E Gigabit Ethernet Controller (rev 11)
and the system works stable with 110us/uframe (~88%) isoc bandwith allocated for
above-mentioned isochronous transfers.
NOTE 3
~~~~~~
This feature is off by default. I mean max periodic bandwidth is set to
100us/uframe by default exactly as it was before the patch. So only those of us
who need the extreme settings are taking the risk - normal users who do not
alter uframe_periodic_max sysfs attribute should not see any change at all.
NOTE 4
~~~~~~
I've tried to update documentation in Documentation/ABI/ thoroughly, but
only "TBD" was put into Documentation/usb/ehci.txt -- the text there seems
to be outdated and much needing refreshing, before it could be amended.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only sysfs attr implemented so far is "companion" from ehci-hub.c,
but in the next patch we are going to add another sysfs file, so prior
to that let's structure things and move already-in-there sysfs code to
separate file.
NOTE: All the code I'm moving into this new file was written by Alan
Stern (in 57e06c11 "EHCI: force high-speed devices to run at full
speed"; Jan 16 2007), that's why I'm putting
Copyright (C) 2007 by Alan Stern
there after explicit request from the author.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Merge ENE UB6250 MS card codes from keucr to drivers/usb/storage/ene_ub6250.c.
Signed-off-by: Cho, Yu-Chen <acho@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds SuperSpeed descriptors to the
g_zero gadget.
The SuperSpeed descriptors were added both for
f_soursesink and f_loopback function drivers.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Amit Blay <ablay@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add SuperSpeed descriptors to the Network USB
function drivers.
This has been lightly tested using a Linux host.
I was able to ssh from device to host and host to
device, no obvious problems seen.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB high speed device must support the TEST_MODE, but the driver
didn't support it. When we sent the SET_FEATURE for TEST_MODE to
the driver, the request was successful, but the module didn't enter
the TEST_MODE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB high speed device must support the TEST_MODE, but the driver
didn't support it. When we sent the SET_FEATURE for TEST_MODE to
the driver, the request was successful, but the module didn't enter
the TEST_MODE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
BUSWAIT is a 4-bit-wide value that controls the number of access waits
from the CPU to on-chip USB module. b'0000 inserts 0 wait (2 access
cycles) and b'1111 inserts 15 waits (17 access cycles, hardware
initial value), respectively.
BUSWAIT value depends on peripheral clock frequency supplied to on-chip
of each CPU, hence should be configurable through platform data.
Note that this patch assumes that b'0000 (0 wait, 2 access cycles) is
rerely used and considered as invalid. If valid 'buswait' data is not
provided by platform, initial b'1111 (15 waits, 17 access cycles) will
be applied as a safe default.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we run rmmod a gadget driver, the driver will call
disable_controller(). Then, because the bit of USBE in SYSCFG0 was
cleared in on_chip=1 mode, we could not connect the usb when we run
insmod a gadget driver next time.
This patch also cleans up probe() and ->stop() about unnecessary
init_controller().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Restoring the missing INDEX register value in musb_restore_context().
Without this suspend resume functionality is broken with offmode
enabled.
Cc: stable@kernel.org
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit e534c5b831 (USB: fix regression
occurring during device removal) didn't go far enough. It failed to
take into account that when a driver claims multiple interfaces, it may
release them all at the same time. As a result, some interfaces can
get released before they are unregistered, and we deadlock trying to
acquire the bandwidth_mutex that we already own.
This patch (asl478) handles this case by setting the "unregistering"
flag on all the interfaces before removing any of them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both fusb300 and langwell udcs seem to only
work with 32-bit address space.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- remove pointer u32 abuse in fusb300_fill_idma_prdtbl().
It is assigned the dma_addr to a pointer and then back.
Poor families may have to recycle variables but we don't
- don't free req.buf in error case. We don't do it in the
ok case so it is probably wrong to do it in error case.
- return in error case. There is no reason to continue
without data and performing ops on an invalid pointer.
- The if (d) statement is bogus since an invalid DMA pointer
is ~0 on some architecutres. And since we return for the
invalid case we don't need it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following compile warning:
| usb/gadget/ci13xxx_udc.c: In function 'show_registers':
| usb/gadget/ci13xxx_udc.c:1242:1: warning: the frame size of 2064 bytes is larger than 1024 bytes
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following compile warnings:
drivers/usb/gadget/net2272.c: In function ‘net2272_kick_dma’:
drivers/usb/gadget/net2272.c:740:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 6 has type ‘dma_addr_t’ [-Wformat]
drivers/usb/gadget/net2272.c: In function ‘net2272_queue’:
drivers/usb/gadget/net2272.c:859:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 8 has type ‘dma_addr_t’ [-Wformat]
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following compile warnings:
drivers/usb/gadget/langwell_udc.c: In function ‘queue_dtd’:
drivers/usb/gadget/langwell_udc.c:596:2: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/langwell_udc.c: In function ‘langwell_udc_probe’:
drivers/usb/gadget/langwell_udc.c:3274:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c:3289:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c: In function ‘langwell_udc_resume’:
drivers/usb/gadget/langwell_udc.c:3473:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c:3487:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
Signed-off-by: Felipe Balbi <balbi@ti.com>
that code has been dead forever. Since the
first commit (0fe6f1d1) the use of that code
has been commented out. Let's drop the dead
code already and fix the following compile
warning:
| drivers/usb/gadget/fusb300_udc.c: At top level:
| drivers/usb/gadget/fusb300_udc.c:771:13: warning: ‘fusb300_wrfifo’ defined but not used [-Wunused-function]
| drivers/usb/gadget/fusb300_udc.c:1027:13: warning: ‘fusb300_set_ep_bycnt’ defined but not used [-Wunused-function]
Signed-off-by: Felipe Balbi <balbi@ti.com>
The autosuspend function can be disabled by unchecking the Macro
CONFIG_REALTEK_AUTOPM in kernel config file, by default, this macro is
turned on.
Signed-off-by: edwin_rong <edwin_rong@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a bug in Samsung's UDC driver, which is completely disabling
the USB device when a custom UDC command is used.
Following patch seems to get the right behavior (e.g. enabling pull-up
instead of disabling then Vcc is applied).
Signed-off-by: Viliam Mateicka <viliam.mateicka@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A compilation warning was added by the patch
"usb: gadget: use config_ep_by_speed() instead of ep_choose()".
This patch fixed it.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With this commit: cccad6d4b1
usb: otg: notifier: switch to atomic notifier
Following dumps are observed on attach/detach for MUSB HOST
mode and on a detach for MUSB Device mode.
BUG: sleeping function called from invalid context at kernel/mutex.c:85
where, the source is:
twl6030_usb_irq
->atomic_notifier_call_chain
->musb_otg_notifications
->twl6030_set_vbus
->twl_i2c_write_u8
->mutex_lock
This patch moves the i2c writes in set_vbus function to a
work-queue thereby avoiding I2C writes in atomic context.
Tested HOST and Device mode functionality on OMAP4460
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
