Change device used for DMA mapping to the MAC device that is an
of_device, with proper DMA ops. Using this device for the netdevice
should also address the issue with DSA scenarios that need the
netdevice to be backed by an of_device.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FMan MAC driver allocates a platform device for the Ethernet
driver to probe on. Setting pdev->dev.of_node with the MAC node
triggers the MAC driver probing of the new platform device. While
this fails quickly and does not affect the functionality of the
drivers, it is incorrect and must be removed. This was added to
address a report that DSA code using of_find_net_device_by_node()
is unable to use the DPAA interfaces. Error message seen before
this fix:
fsl_mac dpaa-ethernet.0: __devm_request_mem_region(mac) failed
fsl_mac: probe of dpaa-ethernet.0 failed with error -16
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes unused timer and its old initialization call.
Cc: Pantelis Antoniou <pantelis.antoniou@gmail.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_ptp_check_pps_event will return 1 if FEC_T_TF_MASK caused
an interrupt. Don't return IRQ_NONE in this case.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FEC_ENET_TS_TIMER is not checked in the interrupt routine
so there is no need to enable it.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before queue 0 was always checked if any queue caused an interrupt.
It is better to just mark queue 0 if queue 0 has caused an interrupt.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
uf_info.regs is resource_size_t i.e. phys_addr_t that can be either u32
or u64 according to CONFIG_PHYS_ADDR_T_64BIT.
The printk format is thus adaptet to u64 and the regs value cast to u64
to take both u32 and u64 into account.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong register is checked for the Tx flow control bit,
it should have been maccfg1 not maccfg2.
This went unnoticed for so long probably because the impact is
hardly visible, not to mention the tangled code from adjust_link().
First, link flow control (i.e. handling of Rx/Tx link level pause frames)
is disabled by default (needs to be enabled via 'ethtool -A').
Secondly, maccfg2 always returns 0 for tx_flow_oldval (except for a few
old boards), which results in Tx flow control remaining always on
once activated.
Fixes: 45b679c9a3 ("gianfar: Implement PAUSE frame generation support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the arrays port_ids on the stack, instead make them static.
Makes the object code smaller by over 700 bytes:
Before:
text data bss dec hex filename
28785 5832 192 34809 87f9 fman.o
After:
text data bss dec hex filename
27921 5992 192 34105 8539 fman.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the skb hash when then FMan Keygen hash result is available.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow ethtool control of the Rx flow hashing. By default RSS is
enabled, this allows to turn it off by bypassing the FMan Keygen
block and sending all traffic on the default Rx frame queue.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a block of 128 Rx frame queues per port. The FMan hardware will
send traffic on one of these queues based on the FMan port Parse
Classify Distribute setup. The hash computed by the FMan Keygen
block will select the Rx FQ.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the FMan Keygen with a hardcoded scheme to spread
incoming traffic on a FQ range based on source and destination IPs
and ports.
Signed-off-by: Iordache Florinel <florinel.iordache@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO header size was defined in many drivers. Factorize the code and
define its size in net/tso.h.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Junote Cai reported that he was not able to get a DSA setup involving the
Freescale DPAA/FMAN driver to work and narrowed it down to
of_find_net_device_by_node(). This function requires the network device's
device reference to be correctly set which is the case here, though we have
lost any device_node association there.
The problem is that dpaa_eth_add_device() allocates a "dpaa-ethernet" platform
device, and later on dpaa_eth_probe() is called but SET_NETDEV_DEV() won't be
propagating &pdev->dev.of_node properly. Fix this by inherenting both the parent
device and the of_node when dpaa_eth_add_device() creates the platform device.
Fixes: 3933961682 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this const as it is only stored in a const field of a
mdiobb_ctrl structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
@match disable optional_qualifier@
identifier s;
@@
static struct ptp_clock_info s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
position ref.p;
identifier match.s,f,c;
expression e;
@@
(
e = s@p
|
e = s@p.f
|
c(...,s@p.f,...)
|
c(...,s@p,...)
)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct ptp_clock_info s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented workarounds for the following dTSEC Erratum:
A002, A004, A0012, A0014, A004839 on several operations
that involve MAC CFG register changes: adjust link,
rx pause frames, modify MAC address.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the return value from -EINVAL to -EOPNOTSUPP. The rest of the
drivers have it like that, so be aligned.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC Receive Control Register has a 14 bit field indicating the
longest frame that may be received. It is being set to 1522. Frames
longer than this are discarded, but counted as being in error.
When using DSA, frames from the switch has an additional header,
either 4 or 8 bytes if a Marvell switch is used. Thus a full MTU frame
of 1522 bytes received by the switch on a port becomes 1530 bytes when
passed to the host via the FEC interface.
Change the maximum receive size to 2048 - 64, where 64 is the maximum
rx_alignment applied on the receive buffer for AVB capable FEC
cores. Use this value also for the maximum receive buffer size. The
driver is already allocating a receive SKB of 2048 bytes, so this
change should not have any significant effects.
Tested on imx51, imx6, vf610.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PHY is missing but expected, e.g. because of a typ0 in the dt
file, it is not possible to open the interface. ip link returns:
RTNETLINK answers: No such device
It is not very obvious what the problem is. Add a netdev_err() in this
case to make it easier to debug the issue.
[ 21.409385] fec 2188000.ethernet eth0: Unable to connect to phy
RTNETLINK answers: No such device
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
19057 392 0 19449 4bf9 drivers/net/ethernet/freescale/gianfar.o
File size After adding 'const':
text data bss dec hex filename
19249 192 0 19441 4bf1 drivers/net/ethernet/freescale/gianfar.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous commit (5567e98919) inserted a dependency on DMA
API that requires HAS_DMA to be added in Kconfig.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the use of arch_setup_dma_ops() that was not exported
and was breaking loadable module compilation.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure dma_ops are set, to be later used by the Ethernet driver.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2b30842b23 ("net: fec: Clear and enable MIB counters on imx51")
introduced fec_enet_clear_ethtool_stats(), but missed to add a stub
for the CONFIG_M5272=y case, causing build failure for the
m5272c3_defconfig.
Add the missing empty stub to fix the build failure.
Fixes: Commit 2b30842b23 ("net: fec: Clear and enable MIB counters on imx51")
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to push the chain index down to the drivers, so they have the
information to which chain the rule belongs. For now, no driver supports
multichain offload, so only chain 0 is supported. This is needed to
prevent chain squashes during offload for now. Later this will be used
to implement multichain offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the IMX51 and IMX53 datasheet indicates that the MIB counters
should be cleared during setup. Otherwise random numbers are returned
via ethtool -S. Add a quirk and a function to do this.
Tested on an IMX51.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NULL check before dereferencing pointer _id_ in order to avoid
a potential NULL pointer dereference.
Addresses-Coverity-ID: 1397995
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY require to wait for a bit after the reset GPIO has been
toggled. This adds support for the DT property `phy-reset-post-delay`
which gives the delay in milliseconds to wait after reset.
If the DT property is not given, no delay is observed. Post reset delay
greater than 1000ms are invalid.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights include:
- rework the Linux page table geometry to lower memory usage on 64-bit Book3S
(IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features on future
firmwares.
- Freescale updates from Scott: "Includes a fix for a powerpc/next mm regression
on 64e, a fix for a kernel hang on 64e when using a debugger inside a
relocated kernel, a qman fix, and misc qe improvements."
Thanks to:
Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong, Nicholas Piggin, Roy
Pledge, Scott Wood, Valentin Longchamp.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YOQs
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"The change to the Linux page table geometry was delayed for more
testing with 16G pages, and there's the new CPU features stuff which
just needed one more polish before going in. Plus a few changes from
Scott which came in a bit late. And then various fixes, mostly minor.
Summary highlights:
- rework the Linux page table geometry to lower memory usage on
64-bit Book3S (IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features
on future firmwares.
- Freescale updates from Scott:
"Includes a fix for a powerpc/next mm regression on 64e, a fix for
a kernel hang on 64e when using a debugger inside a relocated
kernel, a qman fix, and misc qe improvements."
Thanks to: Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong,
Nicholas Piggin, Roy Pledge, Scott Wood, Valentin Longchamp"
* tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Support new device tree binding for discovering CPU features
powerpc: Don't print cpu_spec->cpu_name if it's NULL
of/fdt: introduce of_scan_flat_dt_subnodes and of_get_flat_dt_phandle
powerpc/64s: Fix unnecessary machine check handler relocation branch
powerpc/mm/book3s/64: Rework page table geometry for lower memory usage
powerpc: Fix distclean with Makefile.postlink
powerpc/64e: Don't place the stack beyond TASK_SIZE
powerpc/powernv: Block PCI config access on BCM5718 during EEH recovery
powerpc/8xx: Adding support of IRQ in MPC8xx GPIO
soc/fsl/qbman: Disable IRQs for deferred QBMan work
soc/fsl/qe: add EXPORT_SYMBOL for the 2 qe_tdm functions
soc/fsl/qe: only apply QE_General4 workaround on affected SoCs
soc/fsl/qe: round brg_freq to 1kHz granularity
soc/fsl/qe: get rid of immrbar_virt_to_phys()
net: ethernet: ucc_geth: fix MEM_PART_MURAM mode
powerpc/64e: Fix hang when debugging programs with relocated kernel
Since commit 5093bb965a ("powerpc/QE: switch to the cpm_muram
implementation"), muram area is not part of immrbar mapping anymore
so immrbar_virt_to_phys() is not usable anymore.
Fixes: 5093bb965a ("powerpc/QE: switch to the cpm_muram implementation")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Li Yang <pku.leo@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
The errata ERR007885 HW fix don't add to i.MX6ul ENET IP version,
so add sw workaroud for the chip.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the errata number ERR006358 comment typo.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many boards use i2c/spi expander gpio as phy-reset-gpios and these
gpios maybe registered after fec port, driver should check the return
value of .of_get_named_gpio().
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In aarch64 system, it requires to trasfer ->dev to dma_alloc_coherent()
API, otherwise allocate failed and print kernel warning.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In aarch64 system, the BD pointer is 64bit, and the high-order 32-bits
of the address is effective, so replace usigned with (void *) type to
aovid 64bit address is casted to 32bit in .fec_enet_get_nextdesc() and
.fec_enet_get_prevdesc() functions.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add return value check after calling .of_property_read_u32() to avoid
the warning reported by coverity.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AVOIDBLOCK flag determines the Tx confirmation queues processing
to be redirected to any available CPU when the current one is slow
in processing them. This may result in a higher Tx confirmation
interrupt count but may reduce pressure on a certain CPU that with
the previous setting would process all Tx confirmation frames.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_8xx is being deprecated. Since the includes dependent on
CONFIG_8xx are useless, just drop them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the setup_tc ndo to configure prioritised Tx traffic classes.
Priorities range from 0 (lowest) to 3 (highest). The driver assigns
NR_CPUS queues to each traffic class.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Each traffic class corresponds to a WQ priority level. The number of Tx
netdev queues and frame queues is increased to NR_CPUS queues for each
traffic class. In addition, the priority of the Rx, Error and Conf queues
is lowered but their order is maintained.
By default, only one traffic class is enabled, only the low priority Tx
queues are used and only the corresponding netdev queues are advertised.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
This commit adds the ndo_do_ioctl() callback which allows the userspace to
access PHY registers, for example. This will make mii-diag and similar
tools work.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistake, en_tsu_err_exeption should
be en_tsu_err_exception
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be >= instead of > here. It means that we don't increment
the free count enough so it becomes off by one.
Fixes: 9ad1a37493 ("dpaa_eth: add support for DPAA Ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to use an intermediate variable to handle an error code
in this case.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
'of_node_put(fpi->phy_node)' should also be called if we branch to
'out_deregister_fixed_link' error handling path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fman/fman_memac.c:519:21: error: dereferencing pointer to incomplete type 'struct fixed_phy_status'
Add linux/phy_fixed.h to fman_memac.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In spite of switching to paged allocation of Rx buffers, the driver still
called dma_unmap_single() in the Rx queues tear-down path.
The DMA region unmapping code in free_skb_rx_queue() basically predates
the introduction of paged allocation to the driver. While being refactored,
it apparently hasn't reflected the change in the DMA API usage by its
counterpart gfar_new_page().
As a result, setting an interface to the DOWN state now yields the following:
# ip link set eth2 down
fsl-gianfar ffe24000.ethernet: DMA-API: device driver frees DMA memory with wrong function [device address=0x000000001ecd0000] [size=40]
------------[ cut here ]------------
WARNING: CPU: 1 PID: 189 at lib/dma-debug.c:1123 check_unmap+0x8e0/0xa28
CPU: 1 PID: 189 Comm: ip Tainted: G O 4.9.5 #1
task: dee73400 task.stack: dede2000
NIP: c02101e8 LR: c02101e8 CTR: c0260d74
REGS: dede3bb0 TRAP: 0700 Tainted: G O (4.9.5)
MSR: 00021000 <CE,ME> CR: 28002222 XER: 00000000
GPR00: c02101e8 dede3c60 dee73400 000000b6 dfbd033c dfbd36c4 1f622000 dede2000
GPR08: 00000007 c05b1634 1f622000 00000000 22002484 100a9904 00000000 00000000
GPR16: 00000000 db4c849c 00000002 db4c8480 00000001 df142240 db4c84bc 00000000
GPR24: c0706148 c0700000 00029000 c07552e8 c07323b4 dede3cb8 c07605e0 db535540
NIP [c02101e8] check_unmap+0x8e0/0xa28
LR [c02101e8] check_unmap+0x8e0/0xa28
Call Trace:
[dede3c60] [c02101e8] check_unmap+0x8e0/0xa28 (unreliable)
[dede3cb0] [c02103b8] debug_dma_unmap_page+0x88/0x9c
[dede3d30] [c02dffbc] free_skb_resources+0x2c4/0x404
[dede3d80] [c02e39b4] gfar_close+0x24/0xc8
[dede3da0] [c0361550] __dev_close_many+0xa0/0xf8
[dede3dd0] [c03616f0] __dev_close+0x2c/0x4c
[dede3df0] [c036b1b8] __dev_change_flags+0xa0/0x174
[dede3e10] [c036b2ac] dev_change_flags+0x20/0x60
[dede3e30] [c03e130c] devinet_ioctl+0x540/0x824
[dede3e90] [c0347dcc] sock_ioctl+0x134/0x298
[dede3eb0] [c0111814] do_vfs_ioctl+0xac/0x854
[dede3f20] [c0111ffc] SyS_ioctl+0x40/0x74
[dede3f40] [c000f290] ret_from_syscall+0x0/0x3c
--- interrupt: c01 at 0xff45da0
LR = 0xff45cd0
Instruction dump:
811d001c 7c66482e 813d0020 9061000c 807f000c 5463103a 7cc6182e 3c60c052
386309ac 90c10008 4cc63182 4826b845 <0fe00000> 4bfffa60 3c80c052 388402c4
---[ end trace 695ae6d7ac1d0c47 ]---
Mapped at:
[<c02e22a8>] gfar_alloc_rx_buffs+0x178/0x248
[<c02e3ef0>] startup_gfar+0x368/0x570
[<c036aeb4>] __dev_open+0xdc/0x150
[<c036b1b8>] __dev_change_flags+0xa0/0x174
[<c036b2ac>] dev_change_flags+0x20/0x60
Even though the issue was discovered in 4.9 kernel, the code in question
is identical in the current net and net-next trees.
Fixes: 75354148ce ("gianfar: Add paged allocation and Rx S/G")
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver using dev_alloc_page() must not reuse a page that had to
use emergency memory reserve.
Otherwise all packets using this page will be immediately dropped,
unless for very specific sockets having SOCK_MEMALLOC bit set.
This issue might be hard to debug, because only a fraction of the RX
ring buffer would suffer from drops.
Fixes: 75354148ce ("gianfar: Add paged allocation and Rx S/G")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QBMan CGR options needs to be zeroed before calling the init
function
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fsl/fman drivers will use of_platform_populate() on all
supported platforms. Call of_platform_populate() to probe the
FMan sub-nodes.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
QSGMII ports were not advertising 1G speed.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes and cleanups from David Miller:
1) Revert bogus nla_ok() change, from Alexey Dobriyan.
2) Various bpf validator fixes from Daniel Borkmann.
3) Add some necessary SET_NETDEV_DEV() calls to hsis_femac and hip04
drivers, from Dongpo Li.
4) Several ethtool ksettings conversions from Philippe Reynes.
5) Fix bugs in inet port management wrt. soreuseport, from Tom Herbert.
6) XDP support for virtio_net, from John Fastabend.
7) Fix NAT handling within a vrf, from David Ahern.
8) Endianness fixes in dpaa_eth driver, from Claudiu Manoil
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (63 commits)
net: mv643xx_eth: fix build failure
isdn: Constify some function parameters
mlxsw: spectrum: Mark split ports as such
cgroup: Fix CGROUP_BPF config
qed: fix old-style function definition
net: ipv6: check route protocol when deleting routes
r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detected
irda: w83977af_ir: cleanup an indent issue
net: sfc: use new api ethtool_{get|set}_link_ksettings
net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettings
net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettings
bpf: fix mark_reg_unknown_value for spilled regs on map value marking
bpf: fix overflow in prog accounting
bpf: dynamically allocate digest scratch buffer
gtp: Fix initialization of Flags octet in GTPv1 header
gtp: gtp_check_src_ms_ipv4() always return success
net/x25: use designated initializers
isdn: use designated initializers
...
Ensure correct access to the big endian QMan HW through proper
accessors.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's the default now, no need for makefiles to set it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
