arm,scmi.txt used the wrong document identifier. "ARM DUI 0922B" is
the "ARM Compute Subsystem SCP, Message Interface Protocols". What we
need is the ARM DEN 0056A - "ARM System Control and Management
Interface Platform Design Document".
Fixes: fe7be8b297 ("dt-bindings: arm: add support for ARM System Control and Management Interface(SCMI) protocol")
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
These power supplies provide power for various PLLs that are set up and
driven by the XUSB pad controller. These power supplies were previously
improperly added to the PCIe and XUSB controllers, but depending on the
driver probe order, power to the PLLs will not be supplied soon enough
and cause initialization to fail.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add binding for the QMP based side-channel communication mechanism to
the AOSS, which is used to control resources not exposed through the
RPMh interface.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add compatible for the Amlogic G12B (S922X) SoC based Odroid-N2 SBC
from HardKernel.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add compatible for the Amlogic G12B SoC, sharing most of the
features and architecture with the G12A SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
with DT bindings:
- leds-lm3697
- leds-lm36274
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXQAatQAKCRBiEGxRG/Sl
2/2KAQDHnHR0rIITh3hH49YutOCzGK4oaut8sXfy+8PTEdKBlQEApQP1O1RJTTws
/KDS8qpNdwOQOW/KYiYDX5R8GcOeZwg=
=we/t
-----END PGP SIGNATURE-----
Merge tag 'ti-lmu-led-drivers' into for-next
Merge immutable branch between LEDs, MFD and REGULATOR due to
TI LMU LED support rework and introduction of two new drivers
with DT bindings.
* tag 'ti-lmu-led-drivers':
leds: lm36274: Introduce the TI LM36274 LED driver
dt-bindings: leds: Add LED bindings for the LM36274
regulator: lm363x: Add support for LM36274
mfd: ti-lmu: Add LM36274 support to the ti-lmu
dt-bindings: mfd: Add lm36274 bindings to ti-lmu
leds: lm3697: Introduce the lm3697 driver
mfd: ti-lmu: Remove support for LM3697
dt-bindings: ti-lmu: Modify dt bindings for the LM3697
leds: TI LMU: Add common code for TI LMU devices
dt-bindings: mfd: LMU: Add ti,brightness-resolution
dt-bindings: mfd: LMU: Add the ramp up/down property
Add documentation for the meson vdec dts node.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add all the missing vendors used in Allwinner DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add trigger type setting for csky,mpintc. The driver also could
support #interrupt-cells <1> and it wouldn't invalidate existing
DTs. Here we only show the complete format.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Rob Herring <robh+dt@kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Update the dt-binding document to support new compatible string for the
GPIO interrupt controller which found in Amlogic's Meson-G12A SoC.
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Update the documentation to support clock driver for the Amlogic G12B SoC.
G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the
SYS_PLL are swapped between the clusters
- G12B has additional clocks like for CSI an other components
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Introduce some PHY DLL delays properties to help to sample the PHY clock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some Spreadtrum platforms like SC9860 platform, we should enable another
gate clock '2x_enable' to make the SD host controller work well. Thus add
documentation for this optional clock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Switch the DT binding to a YAML schema to enable the DT validation.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC controllers have a bunch of generic options that are needed in a
device tree. Add a YAML schemas for those.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On the Amlogic G12A SoC family, (only) the SDIO controller has a bug which
makes any DRAM access from the MMC controller fail.
Add the amlogic,dram-access-quirk property so signal this particular
controller has this bug and needs a quirk to work properly.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Keystone 2 66AK2HK/E/L 1G Ethernet Switch Subsystems contains The
Common Platform Time Sync (CPTS) module which is in general compatible with
CPTS module found on "legacy" TI AM3/4/5 SoCs. So, the basic support for
Keystone 2 CPTS is available by default, but not documented.
The Keystone 2 CPTS module supports also some additional features like time
sync reference (RFTCLK) clock selection through CPTS_RFTCLK_SEL register
(offset: x08) in CPTS module, which is modelled as multiplexer clock.
This patch adds missed binding documentation for Keystone 2 66AK2HK/E/L
CPTS module.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly due to x86 and acpi conversion, several documentation
links are still pointing to the old file. Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Reviewed-by: Bhupesh Sharma <bhsharma@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add a new optional renesas,companion property to point to the companion
LVDS encoder. This is used to support dual-link operation where the main
LVDS encoder splits even-numbered and odd-numbered pixels between the
two LVDS encoders.
The new property doesn't control the mode of operation, it only
describes the relationship between the master and companion LVDS
encoders.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The THC63LVD1024 LVDS decoder can operate in two modes, single-link or
dual-link. In dual-link mode both input ports are used to carry even-
and odd-numbered pixels separately. Document this in the DT bindings,
along with the related rules governing port and usage.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Add SGPM pinmux to ast2500-pinctrl function and group, to prepare for
supporting SGPIO in AST2500 SoC.
Signed-off-by: Hongwei Zhang <hongweiz@ami.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ufs_reset pin is expected to be wired to the reset pin of the
primary UFS memory but is pretty much just a general purpose output pinr
Reorder the pins and expose it as gpio 150, so that the UFS driver can
toggle it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The i.MX8MM pinfunc head file is located in DT folder, correct it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch adds k3 am654 compatible, specific properties and
an example.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fully compatible with mcp2515, the mcp25625 have integrated transceiver.
This patch add the mcp25625 to the device tree bindings documentation.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some new files got converted to yaml, but references weren't
updated accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the LM36274 LED specific bindings.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The filename matches mtk-uart-apdma.c.
So using "mtk-uart-apdma.txt" should be better.
And add some property.
Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There's a new driver using the SPI memory interface of the
SPI framework at spi/spi-stm32-qspi.c, which can be used
together with m25p80.c to replace the functionality of
this SPI NOR driver.
The "new" driver uses the same dt properties and not affects
the legacy compatibility.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The GPU for msm8998 has its own clock controller. Document it.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The axienet driver requires the use of an axistream-connected attribute,
but this isn't documented in the devicetree bindings. Document how this
attribute is supposed to be used, including the upcoming change to make
the usage of this attribute optional.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio child node for the MDIO bus is generally required when using
this driver but was not documented other than being shown in the
example. Document it as an optional (but usually required) parameter.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously this driver only handled interrupts from the DMA RX and TX
blocks, not from the Ethernet core itself. Add optional support for
the Ethernet core interrupt, which is used to detect rx_missed and
framing errors signalled by the hardware. In order to use this
interrupt, a third interrupt needs to be specified in the device tree.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was previously always calculating the MDIO clock divisor
(from AXI bus clock to MDIO bus clock) based on the CPU clock frequency,
assuming that it is the same as the AXI bus frequency, but that
simplistic method only works on the MicroBlaze platform.
Add support for specifying the clock used for the device in the device
tree using the clock framework. If the clock is specified then it will
be used when calculating the clock divisor. The previous CPU clock
detection method is left for backward compatibility if no clock is
specified.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems implement virtio-iommu as a PCI endpoint. The operating
system needs to discover the relationship between IOMMU and masters long
before the PCI endpoint gets probed. Add a PCI child node to describe the
virtio-iommu device.
The virtio-pci-iommu is conceptually split between a PCI programming
interface and a translation component on the parent bus. The latter
doesn't have a node in the device tree. The virtio-pci-iommu node
describes both, by linking the PCI endpoint to "iommus" property of DMA
master nodes and to "iommu-map" properties of bus nodes.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The nature of a virtio-mmio node is discovered by the virtio driver at
probe time. However the DMA relation between devices must be described
statically. When a virtio-mmio node is a virtio-iommu device, it needs an
"#iommu-cells" property as specified by bindings/iommu/iommu.txt.
Otherwise, the virtio-mmio device may perform DMA through an IOMMU, which
requires an "iommus" property. Describe these requirements in the
device-tree bindings documentation.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add the "altr,socfpga-stmmac-a10-s10" binding for Arria10/Agilex/Stratix10
implementation of the stmmac ethernet controller.
On the Arria10, Agilex, and Stratix10 SoCs, there are a few differences from
the Cyclone5 and Arria5:
- The emac PHY setup bits are in separate registers.
- The PTP reference clock select mask is different.
- The register to enable the emac signal from FPGA is different.
Because of these differences, the dwmac-socfpga glue logic driver will
use this new binding to set the appropriate bits for PHY, PTP reference
clock, and signal from FPGA.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the LM36274 backlight driver with regulator support.
This is a multi-function device for backlight applications.
Backlight properties will be documented in it's a supplemental
bindings document.
Regulator support is documented in the regulator/lm363x-regulator.txt
http://www.ti.com/lit/ds/symlink/lm36274.pdf
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The R40 has a pretty different RTC compared to the other SoCs we've
encountered so far, the most important difference being that it now has
only a single interrupt, compared to the previous SoCs having two.
Let's add a compatible for that.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The newer Allwinner SoCs have an embedded RTC supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The older Allwinner SoCs have an embedded RTC supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC generic bindings has a bunch of devices that have a pretty simple
binding, with just compatible, reg and optional interrupts properties.
This is exactly what the trivial devices YAML schema has been created for,
except that they can also have the start-year property, but not any other
generic RTC property.
Let's create a schema with those constraints.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The real time clocks have a bunch of generic properties that are needed in
a device tree. Add a YAML schemas for those.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add "Jiangsu HopeRun Software Co., Ltd." to the list of devicetree
vendor prefixes as "hoperun".
Website: http://www.hoperun.com/en
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In certain situations it was seen that we could wedge up the DDC bus
on the HDMI adapter on rk3288. The only way to unwedge was to mux one
of the pins over to GPIO output-driven-low temporarily and then
quickly mux back. Full details can be found in the patch
("drm/bridge/synopsys: dw-hdmi: Add "unwedge" for ddc bus").
Since unwedge requires remuxing the pins, we first need to add to the
bindings so that we can specify what state the pins should be in for
unwedging.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190502225336.206885-1-dianders@chromium.org
The Allwinner SoCs have a clocks controller supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the A64 compatible with a fallback to the A83T compatible.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The mv88e6250 has port_base_addr 0x8 or 0x18 (depending on
configuration pins), so it constitutes a new family and hence needs
its own compatible string.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation for Device-Tree bindings for the
Socionext Synquacer spi driver.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA in H6 is similar to other DMA controller, except it is first which
supports more than 32 request sources and has 16 channels. It also needs
additional clock to be enabled.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver is gaining power domain support, so add the new property
to the DT binding and update the examples.
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add binding document for the ethernet on MT7629 SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add an extra required property "mediatek,physpeed" to sgmiisys to determine
link speed to match up the capability of the target PHY.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8df39e1687 ("media: dt-bindings: media: Add vendor prefix for
allegro") introduced a new devicetree binding vendors, however with an
improper syntax making the resulting YAML impossible to parse. Let's fix
this.
Fixes: 8df39e1687 ("media: dt-bindings: media: Add vendor prefix for allegro")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qualcomm PCIe2 PHY is a Synopsys based PCIe PHY found in a number of
Qualcomm platforms, add a binding to describe this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Allwinner SoCs have a MIPI-DSI and MIPI-D-PHY controllers supported in
Linux, with a matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190527120910.18964-1-maxime.ripard@bootlin.com
Even though the SWAC is just a baseboard to the icnova SoM, the vendor of
the baseboard somehow ended up with the board name instead of the vendor
name. Fix that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Move the binding for the discrete Atmel I2C Elliptic Curve h/w crypto
module to trivial-devices.yaml, as it doesn't belong in atmel-crypto
which describes unrelated on-SoC peripherals.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a compatible string for the Atmel SHA204A I2C crypto processor.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add RPM power domain bindings for the msm8998 family of SoC
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add RPM power domain bindings for the qcs404 family of SoC
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sibis: Add supported rpmpd states for qcs404]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The Qualcomm QCS404 platform contains a PCIe controller, add this to the
Qualcomm PCI binding document. The controller is the same version as the
one used in IPQ4019, but the PHY part is described separately, hence the
difference in clocks and resets.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
The A83T SoC has a camera sensor interface (known as CSI in Allwinner
lingo), which is similar to the one found on the A64 and H3. The only
difference seems to be that support of MIPI CSI through a connected
MIPI CSI-2 bridge.
Add a compatible string for this variant.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add vendor prefix for Allegro DVT, a provider of H.264/AVC, H.265/HEVC,
AVS2, VP9 and AV1 compliance test suites and H.264/AVC, H.265/HEVC, and
VP9 encoder, codec and decoder hardware (RTL) IPs.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add device-tree bindings for the Allegro DVT video IP core found on the
Xilinx ZynqMP EV family.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add DT bindings for the Renesas RZ/A1 Interrupt Controller.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlzrJgUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1XAIAJajJpeKc9MVQipi
zWiI+WgHDg8gG/HnLKzP2Zp4MUjTCz30t0rnBbdo6AyK6LnPBL53yxg9q64XN7vI
p/h2ys+/DvqhIYSPWX6C++HYQT4Cb5ghxJABEIsztd3G4nfB9L2vgq9zKSNFusTD
UtfUxufciZPX515TuE4IqWMwS4Ut5daH7V3jjZunhPiayTFv64e1KbpKLLzHR0NR
DfFbrPcdp7VyCT/A5AKrqfqeB6O9dm/Fe4CsdsaKuzASCXJ6GUc/A7iZDndv/KA4
f5Xh7SGlQ2TfT1ud/aMfdw3AcMjqB8zgMJenovJ7UuHDfULBWNeAmMh/cTDwY9eY
Xgyvfm0=
=S8p9
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc2' into patchwork
Merge back from upstream into media tree, as there are some
patches merged upstream that has pontential of causing
conflicts (one actually rised a conflict already).
Linux 5.2-rc2
* tag 'v5.2-rc2': (377 commits)
Linux 5.2-rc2
random: fix soft lockup when trying to read from an uninitialized blocking pool
tracing: Silence GCC 9 array bounds warning
ext4: fix dcache lookup of !casefolded directories
locking/lock_events: Use this_cpu_add() when necessary
KVM: x86: fix return value for reserved EFER
tools/kvm_stat: fix fields filter for child events
KVM: selftests: Wrap vcpu_nested_state_get/set functions with x86 guard
kvm: selftests: aarch64: compile with warnings on
kvm: selftests: aarch64: fix default vm mode
kvm: selftests: aarch64: dirty_log_test: fix unaligned memslot size
KVM: s390: fix memory slot handling for KVM_SET_USER_MEMORY_REGION
KVM: x86/pmu: do not mask the value that is written to fixed PMUs
KVM: x86/pmu: mask the result of rdpmc according to the width of the counters
x86/kvm/pmu: Set AMD's virt PMU version to 1
KVM: x86: do not spam dmesg with VMCS/VMCB dumps
kvm: Check irqchip mode before assign irqfd
kvm: svm/avic: fix off-by-one in checking host APIC ID
KVM: selftests: do not blindly clobber registers in guest asm
KVM: selftests: Remove duplicated TEST_ASSERT in hyperv_cpuid.c
...
The A83t and compatibles controllers don't have any reception capabilities
on some instances of the controllers, even though it was never documented
as such in the binding before.
Therefore, on those controllers, we don't have the option to set an RX DMA
channel.
This was already done in the DTSI, but the binding itself was never
updated. Let's add a special case in the schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Allwinner SoCs feature an I2S controller across multiple SoC
generations.
However, earlier generations were a bit simpler than the subsequent ones,
and for example would always have RX and TX capabilities, and no reset
lines.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner H6 has a SPDIF controller with an increase of the fifo
size and a sligher difference in memory mapping compare to H3/A64.
This make it not compatible with the previous generation.
Introduce a specific bindings for H6 SoC.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the Arm PL061 GPIO controller binding to json-schema format.
As I'm the author for all but the gpio-ranges line, make the schema dual
GPL/BSD license.
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Because this patch series dropped support for 10 bit I2C devices, I'm
documenting this.
Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Some new touchpads IC are connected through PS/2 and I2C. On some of these
new IC, the I2C part doesn't have all of the information available.
We need to be able to forward the touchpad parameters from PS/2 and
thus, we need those new optional properties.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cross-subsystem Changes:
- Fix device tree bindings in drm-misc-next after a botched merge.
Core Changes:
- Docbook fix for drm_hdmi_infoframe_set_hdr_metadata.
Driver Changes:
- mediatek: Fix compiler warning after merging the HDR series.
- vc4: Rework binner bo handling.
-----BEGIN PGP SIGNATURE-----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=2K7c
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-05-24' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3, try #2:
UAPI Changes:
- Add HDR source metadata property.
- Make drm.h compile on GNU/kFreeBSD by including stdint.h
- Clarify how the userspace reviewer has to review new kernel UAPI.
- Clarify that for using new UAPI, merging to drm-next or drm-misc-next should be enough.
Cross-subsystem Changes:
- video/hdmi: Add unpack function for DRM infoframes.
- Device tree bindings:
* Updating a property for Mali Midgard GPUs
* Updating a property for STM32 DSI panel
* Adding support for FriendlyELEC HD702E 800x1280 panel
* Adding support for Evervision VGG804821 800x480 5.0" WVGA TFT panel
* Adding support for the EDT ET035012DM6 3.5" 320x240 QVGA 24-bit RGB TFT.
* Adding support for Three Five displays TFC S9700RTWV43TR-01B 800x480 panel
with resistive touch found on TI's AM335X-EVM.
* Adding support for EDT ETM0430G0DH6 480x272 panel.
- Add OSD101T2587-53TS driver with DT bindings.
- Add Samsung S6E63M0 panel driver with DT bindings.
- Add VXT VL050-8048NT-C01 800x480 panel with DT bindings.
- Dma-buf:
- Make mmap callback actually optional.
- Documentation updates.
- Fix debugfs refcount inbalance.
- Remove unused sync_dump function.
- Fix device tree bindings in drm-misc-next after a botched merge.
Core Changes:
- Add support for HDR infoframes and related EDID parsing.
- Remove prime sg_table caching, now done inside dma-buf.
- Add shiny new drm_gem_vram helpers for simple VRAM drivers;
with some fixes to the new API on top.
- Small fix to job cleanup without timeout handler.
- Documentation fixes to drm_fourcc.
- Replace lookups of drm_format with struct drm_format_info;
remove functions that become obsolete by this conversion.
- Remove double include in bridge/panel.c and some drivers.
- Remove drmP.h include from drm/edid and drm/dp.
- Fix null pointer deref in drm_fb_helper_hotplug_event().
- Remove most members from drm_fb_helper_crtc, only mode_set is kept.
- Remove race of fb helpers with userspace; only restore mode
when userspace is not master.
- Move legacy setup from drm_file.c to drm_legacy_misc.c
- Rework scheduler job destruction.
- drm/bus was removed, remove from TODO.
- Add __drm_atomic_helper_crtc_reset() to subclass crtc_state,
and convert some drivers to use it (conversion is not complete yet).
- Bump vblank timeout wait to 100 ms for atomic.
- Docbook fix for drm_hdmi_infoframe_set_hdr_metadata.
Driver Changes:
- sun4i: Use DRM_GEM_CMA_VMAP_DRIVER_OPS instead of definining manually.
- v3d: Small cleanups, adding support for compute shaders,
reservation/synchronization fixes and job management refactoring,
fixes MMU and debugfs.
- lima: Fix null pointer in irq handler on startup, set default timeout for scheduled jobs.
- stm/ltdc: Assorted fixes and adding FB modifier support.
- amdgpu: Avoid hw reset if guilty job was already signaled.
- virtio: Add seqno to fences, add trace events, use correct flags for fence allocation.
- Convert AST, bochs, mgag200, vboxvideo, hisilicon to the new drm_gem_vram API.
- sun6i_mipi_dsi: Support DSI GENERIC_SHORT_WRITE_2 transfers.
- bochs: Small fix to use PTR_RET_OR_ZERO and driver unload.
- gma500: header fixes
- cirrus: Remove unused files.
- mediatek: Fix compiler warning after merging the HDR series.
- vc4: Rework binner bo handling.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/052875a5-27ba-3832-60c2-193d950afdff@linux.intel.com
The spelling of configured is incorrect in the documentation. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add binding documentation for Atheros/QCA networking IP core used
in many routers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the text file, simtek didn't have any description and apparently this
confused the conversion script. Fix the simtek entry and add a proper
description.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Single quotes need to be escaped in YAML, make sure it's the case.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch adds support for the Armadeus ST0700 Adapt. It comes with a
Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT and an adapter board so
that it can be connected on the TFT header of Armadeus Dev boards.
Cc: stable@vger.kernel.org # v4.19
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507152713.27494-1-sebastien.szymanski@armadeus.com
We shouldn't reference Linux kernel functions or Linux itself in proper
bindings. It's OK to reference functions in the kernel when explaining
examples, but otherwise we shouldn't reference functions to describe
what the binding means.
Cc: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add Espressif Systems DT vendor prefix. That prefix has been used for quite
some time for WiFi chips, but has never been documented.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The LM3697 is a single function LED driver. The single function LED
driver needs to reside in the LED directory as a dedicated LED driver
and not as a MFD device. The device does have common brightness and ramp
features and those can be accomodated by a TI LMU framework.
The LM3697 dt binding needs to be moved from the ti-lmu.txt and a dedicated
LED dt binding needs to be added. The new LM3697 LED dt binding will then
reside in the Documentation/devicetree/bindings/leds directory and follow the
current LED and general bindings guidelines.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Add new interface mode USXGMII to binding documentation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the binding documentation for a simple SPI based LED
controller which use only one byte for setting the brightness.
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Allwinner H6 has a similar watchdog as the A64 which is already
a compatible of the A31.
This commit add the H6 compatible.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Earlier, the PWM registers were included as part of the pinctrl memory
map, but this turned to be useless as the muxing is being handled by the
SoC pin controller itself. So, lets modify the pinctrl memory map to
reflect the same.
Fixes: 07b734fbde ("dt-bindings: pinctrl: Add BM1880 pinctrl binding")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
add support for the pinconf DT property output-enable, output-disable,
output-low and output-high in the meson pinctrl driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the STM32 pinctrl binding to DT schema format using json-schema.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the Arm pl022 binding to DT schema format. The clock binding was
missing, so it is added to the schema. It really should be required as
well, but there are some platforms (spear) not yet using DT clock
binding.
Cc: Mark Brown <broonie@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-spi@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
BCM7211 has a slightly different block layout and some additional GPIO
registers that were added, document the compatible string.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This property allow drive-strength parameter in uA instead of mA.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The canvas IP on Meson8, Meson8b and Meson8m2 is similar to the one
found on GXBB and newer. The only known difference is that the older
SoCs cannot configure the "endianness".
Add a compatible string for each of the older SoCs to make sure we won't
be using unsupported features on these SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The clock output is generally only used for testing and development and
not used to daisy-chain PHYs. It's just a source of RF noise afterward.
Add a mux value for "off". I've added it as another enumeration to the
output property. In the actual PHY, the mux and the output enable are
independently controllable. However, it doesn't seem useful to be able
to describe the mux setting when the output is disabled.
Document that PHY's default setting will be left as is if the property
is omitted.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a note to make it more clear how the driver behaves when "rgmii" vs
"rgmii-id", "rgmii-idrx", or "rgmii-idtx" interface modes are selected.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SoCs adds a bus clock gate to the Mali Midgard GPU.
Add the binding for the bus clock.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521161102.29620-4-peron.clem@gmail.com
nand-controller.yaml replaced nand.txt however the references to it were
not updated. This change updates these references wherever it appears in
bindings documentation.
Fixes: 212e496935 ("dt-bindings: mtd: Add YAML schemas for the generic NAND options")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Validating the examples against the schema have a few errors:
arm,gic.example.dt.yaml: 'ranges' does not match any of the regexes: '^v2m@[0-9a-f]+$', 'pinctrl-[0-9]+'
arm,gic.example.dt.yaml: #address-cells:0:0: 2 is not one of [0, 1]
arm,gic.example.dt.yaml: #size-cells:0:0: 1 was expected
'ranges' is valid, but missing from the schema, so add it. The reg
addresses and sizes don't match the schema requirements and the example
template. We could just override the example template to use 64-bit
addresses, but there's not really any value showing that in the example.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Following commit 31af04cd60 ("arm64: dts: Remove inconsistent use of
'arm,armv8' compatible string"), clean up these binding examples in case
anyone is tempted to copy them.
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
These files were converted to json-schema, but the references weren't
renamed.
Fixes: 66ed144f14 ("dt-bindings: interrupt-controller: Convert ARM GIC to json-schema")
(and other similar commits)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
In order to have $ref's to schema files within the kernel, we need to
pass the base path of bindings to the schema validation tools.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: devicetree@vger.kernel.org
Cc: linux-kbuild@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
For IP blocks that are generated from the public, open-source
sifive-blocks repository, describe the version numbering policy
that its maintainers intend to use, upon request from Rob
Herring <robh@kernel.org>.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Megan Wachs <megan@sifive.com>
Cc: Wesley Terpstra <wesley@sifive.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the max8660 binding to DT schema format using json-schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the gpio-regulator binding to DT schema format using
json-schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the common regulator binding to DT schema format. Note that all
the properties with standard unit suffixes have type checks already, so
only a description is necessary.
As fixed-regulator has already been converted, update the references in
it. Otherwise, keep regulator.txt with a reference to the schema to
avoid a bunch of treewide updates. regulator.txt can be removed when all
the regulator bindings are converted.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the spi-gpio binding to DT schema format.
Cc: Mark Brown <broonie@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing qcom,remote-pid dt binding required for GLINK SMEM
which specifies the remote endpoint of the GLINK edge.
Fixes: 2b41d6c8e6 ("dt-bindings: soc: qcom: Extend GLINK to cover SMEM")
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The SDM845 Audio DSP peripheral image loader binding describes the
properties needed to load and boot firmware on a Hexagon v56. Rename the
file and add the Compute DSP (CDSP) found in QCS404 to the binding.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Switch the DT binding to a YAML schema to enable the DT validation.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch the DT binding to a YAML schema to enable the DT validation.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI controllers have a bunch of generic options that are needed in a
device tree. Add a YAML schemas for those.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Arizona regulator drivers are now also used by the Cirrus Logic
Madera audio CODECs, update the binding document to link to the primary
binding document for these as well as the existing Arizona document.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert Amlogic SoC bindings to DT schema format using json-schema.
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: updated maninainers]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
It is best practice to have 1 binding per file, so board level bindings
should be separate for various misc SoC bindings.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds a devicetree binding documentation for
FSL's DPAA2 console.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add ti,brightness-resolution to the TI LMU binding to define
whether the device uses 8-bit brightness or 11-bit brightness.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Document the ramp-up and ramp-down property in the binding.
Removing the "sec" from the property definition as seconds is
implied.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The OLPC XO-1.75 Embedded Controller is a SPI master that uses extra
signals for handshaking. It needs to know when is the slave (Linux)
side's TX FIFO ready for transfer (the ready-gpio signal on the SPI
controller node) and when does it wish to respond with a command (the
cmd-gpio property).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This patch adds board HiHope RZ/G2M (the main board, powered by
the R8A774A1) and board HiHope RZ/G2 EX (the expansion board
that sits on top of the HiHope RZ/G2M). Both boards are made
by Jiangsu HopeRun Software Co., Ltd. (a.k.a. HopeRun).
Useful links:
http://hihope.org/product/detail/rzg2https://item.taobao.com/item.htm?spm=a2oq0.12575281.0.0.6bcf1debQpzkRS&ft=t&id=592177498472http://www.hoperun.com/Cn/news/id/379
We already know that the HiHope RZ/G2 EX will also sit on the
HiHope RZ/G2N, even though the HiHope RZ/G2N doesn't exist just
yet.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The newer Allwinner SoCs feature a bus designed for the PMIC, similar to
I2C called RSB. Let's convert the device tree bindings for that bus over to
a YAML schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The interpretation of opp-supported-hw bits for imx-cpufreq-dt driver is
not very obvious so attempt to explain it.
There is no OF compat string associated.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
New device support
* mt6577
- add supprot for the mt6765 which requires a few minor additional
new features in the driver.
Yaml binding conversions
* adxl345
* isl29018
* tsl2583
* tsl2772
Minor features and improvements
* ad5758
- declare an of_device_id table rather than just relying on the spi
fallback which doesn't use the manufacturer id.
- drop a set but not used variable left from previous refactor.
* ad7816
- Add a bit more description to kconfig text.
* ad9523
- change calculation order to improve frequency accuracy.
* adxl372
- declare an of_device_id table
* adt7316
- white space.
* at91_adc
- Use dev_get_drvdata directly rather than boucing to the platform device
and back again.
* cros_ec
- add an id sysfs entry to bring in line with the other implementations.
* ds5522
- drop a check on the of_node existing as we don't actually use it for
anything.
* kxsd9
- declare an of_device_id table.
* maxim_thermocouple
- declare an of_device_id table.
* mt6577
- add dt binding entry for mt8183 which is also supported.
* rcar-gyroadc
- tidy up unnecessary error messages.
* stm32-dfsdm
- improved error handling.
* stmpe-adc
- drop an unnecessary variable assignment.
- add an of_device_id table.
- reinit completion on begin converstion to avoid a path in which
previous round had been interrupted, also switch to non interruptible
wait to avoid an issue with a user program using -pg
- simplify interrupt handling by just having them always enabled.
- reset all interrupts on startup and in the timeout handler to
avoid getting stuck.
* sun4i-gpadc
- SPDX
-----BEGIN PGP SIGNATURE-----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=dKoi
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.3a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.3 cycle
New device support
* mt6577
- add supprot for the mt6765 which requires a few minor additional
new features in the driver.
Yaml binding conversions
* adxl345
* isl29018
* tsl2583
* tsl2772
Minor features and improvements
* ad5758
- declare an of_device_id table rather than just relying on the spi
fallback which doesn't use the manufacturer id.
- drop a set but not used variable left from previous refactor.
* ad7816
- Add a bit more description to kconfig text.
* ad9523
- change calculation order to improve frequency accuracy.
* adxl372
- declare an of_device_id table
* adt7316
- white space.
* at91_adc
- Use dev_get_drvdata directly rather than boucing to the platform device
and back again.
* cros_ec
- add an id sysfs entry to bring in line with the other implementations.
* ds5522
- drop a check on the of_node existing as we don't actually use it for
anything.
* kxsd9
- declare an of_device_id table.
* maxim_thermocouple
- declare an of_device_id table.
* mt6577
- add dt binding entry for mt8183 which is also supported.
* rcar-gyroadc
- tidy up unnecessary error messages.
* stm32-dfsdm
- improved error handling.
* stmpe-adc
- drop an unnecessary variable assignment.
- add an of_device_id table.
- reinit completion on begin converstion to avoid a path in which
previous round had been interrupted, also switch to non interruptible
wait to avoid an issue with a user program using -pg
- simplify interrupt handling by just having them always enabled.
- reset all interrupts on startup and in the timeout handler to
avoid getting stuck.
* sun4i-gpadc
- SPDX
* tag 'iio-for-5.3a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (28 commits)
iio: adc: mediatek: mt6577-auxadc, add mt6765 support
dt-bindings: iio: adc: mediatek: Add document for mt6765
dt-bindings: iio: accel: adxl345: switch to YAML bindings
iio: adc: sun4i-gpadc-iio convert to SPDX license tags
iio: ad9523-1: Improve reported VCO frequency accuracy
iio: dac: ds4422/ds4424 drop of_node check
iio: stmpe-adc: Reset possible interrupts
iio: stmpe-adc: Use wait_for_completion_timeout
iio: stmpe-adc: Enable all stmpe-adc interrupts just once
iio: stmpe-adc: Reinit completion struct on begin conversion
iio: stmpe-adc: Add compatible name
iio: stmpe-adc: Remove unnecessary assignment
staging: iio: adc: Add paragraph to describe Kconfig symbol
staging: iio: adt7316: match parenthesis alignment
iio: adc: rcar-gyroadc: Remove devm_iio_device_alloc() error printing
dt-bindings: iio: isl29018: convert bindings to YAML format
dt-bindings: adc: mt8183: add binding document
iio: dac: ad5758: remove set but not used variable 'dc_dc_mode'
iio: cros_ec: add 'id' sysfs entry
iio: adc: stm32-dfsdm: missing error case during probe
...
Pull clocksource updates from Ingo Molnar:
"Misc clocksource/clockevent driver updates that came in a bit late but
are ready for v5.2"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
misc: atmel_tclib: Do not probe already used TCBs
clocksource/drivers/timer-atmel-tcb: Convert tc_clksrc_suspend|resume() to static
clocksource/drivers/tcb_clksrc: Rename the file for consistency
clocksource/drivers/timer-atmel-pit: Rework Kconfig option
clocksource/drivers/tcb_clksrc: Move Kconfig option
ARM: at91: Implement clocksource selection
clocksource/drivers/tcb_clksrc: Use tcb as sched_clock
clocksource/drivers/tcb_clksrc: Stop depending on atmel_tclib
ARM: at91: move SoC specific definitions to SoC folder
clocksource/drivers/timer-milbeaut: Cleanup common register accesses
clocksource/drivers/timer-milbeaut: Add shutdown function
clocksource/drivers/timer-milbeaut: Fix to enable one-shot timer
clocksource/drivers/tegra: Rework for compensation of suspend time
clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804
clocksource/drivers/sun4i: Add a compatible for suniv
dt-bindings: timer: Add Allwinner suniv timer
Pull IRQ chip updates from Ingo Molnar:
"A late irqchips update:
- New TI INTR/INTA set of drivers
- Rewrite of the stm32mp1-exti driver as a platform driver
- Update the IOMMU MSI mapping API to be RT friendly
- A number of cleanups and other low impact fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
arm64: arch_k3: Enable interrupt controller drivers
irqchip/ti-sci-inta: Add msi domain support
soc: ti: Add MSI domain bus support for Interrupt Aggregator
irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
irqchip/ti-sci-intr: Add support for Interrupt Router driver
dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
gpio: thunderx: Use the default parent apis for {request,release}_resources
genirq: Introduce irq_chip_{request,release}_resource_parent() apis
firmware: ti_sci: Add helper apis to manage resources
firmware: ti_sci: Add RM mapping table for am654
firmware: ti_sci: Add support for IRQ management
firmware: ti_sci: Add support for RM core ops
...
This is some material that we picked up into our tree late. Most of it
are smaller fixes and additions, some defconfig updates due to recent
development, etc.
Code-wise the largest portion is a series of PM updates for the at91
platform, and those have been in linux-next a while through the at91
tree before we picked them up.
-----BEGIN PGP SIGNATURE-----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=XCCp
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late. Most of it
are smaller fixes and additions, some defconfig updates due to recent
development, etc.
Code-wise the largest portion is a series of PM updates for the at91
platform, and those have been in linux-next a while through the at91
tree before we picked them up"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits)
arm64: dts: sprd: Add clock properties for serial devices
Opt out of scripts/get_maintainer.pl
ARM: ixp4xx: Remove duplicated include from common.c
soc: ixp4xx: qmgr: Fix an NULL vs IS_ERR() check in probe
arm64: tegra: Disable XUSB support on Jetson TX2
arm64: tegra: Enable SMMU translation for PCI on Tegra186
arm64: tegra: Fix insecure SMMU users for Tegra186
arm64: tegra: Select ARM_GIC_PM
amba: tegra-ahb: Mark PM functions as __maybe_unused
ARM: dts: logicpd-som-lv: Fix MMC1 card detect
ARM: mvebu: drop return from void function
ARM: mvebu: prefix coprocessor operand with p
ARM: mvebu: drop unnecessary label
ARM: mvebu: fix a leaked reference by adding missing of_node_put
ARM: socfpga_defconfig: enable LTC2497
ARM: mvebu: kirkwood: remove error message when retrieving mac address
ARM: at91: sama5: make ov2640 as a module
ARM: OMAP1: ams-delta: fix early boot crash when LED support is disabled
ARM: at91: remove HAVE_FB_ATMEL for sama5 SoC as they use DRM
soc/fsl/qe: Fix an error code in qe_pin_request()
...
This patch set contains an assortment of RISC-V related patches that I'd
like to target for the 5.2 merge window. Most of the patches are
cleanups, but there are a handful of user-visible changes:
* The nosmp and nr_cpus command-line arguments are now supported, which
work like normal.
* The SBI console no longer installs itself as a preferred console, we
rely on standard mechanisms (/chosen, command-line, hueristics)
instead.
* sfence_remove_sfence_vma{,_asid} now pass their arguments along to the
SBI call.
* Modules now support BUG().
* A missing sfence.vma during boot has been added. This bug only
manifests during boot.
* The arch/riscv support for SiFive's L2 cache controller has been
merged, which should un-block the EDAC framework work.
I've only tested this on QEMU again, as I didn't have time to get things
running on the Unleashed. The latest master from this morning merges in
cleanly and passes the tests as well.
This patch set rebased my "5.2 MW, Part 1" patch set which includes an
erronous empty file. It's also a rebase of my "5.2 MW, Part 2" patch
set, in which I managed to create another file while attempting to
remove the empty file.
Sorry for all the noise!
-----BEGIN PGP SIGNATURE-----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=mZwx
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains an assortment of RISC-V related patches that I'd like to
target for the 5.2 merge window. Most of the patches are cleanups, but
there are a handful of user-visible changes:
- The nosmp and nr_cpus command-line arguments are now supported,
which work like normal.
- The SBI console no longer installs itself as a preferred console,
we rely on standard mechanisms (/chosen, command-line, hueristics)
instead.
- sfence_remove_sfence_vma{,_asid} now pass their arguments along to
the SBI call.
- Modules now support BUG().
- A missing sfence.vma during boot has been added. This bug only
manifests during boot.
- The arch/riscv support for SiFive's L2 cache controller has been
merged, which should un-block the EDAC framework work.
I've only tested this on QEMU again, as I didn't have time to get
things running on the Unleashed. The latest master from this morning
merges in cleanly and passes the tests as well"
* tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux: (31 commits)
riscv: fix locking violation in page fault handler
RISC-V: sifive_l2_cache: Add L2 cache controller driver for SiFive SoCs
RISC-V: Add DT documentation for SiFive L2 Cache Controller
RISC-V: Avoid using invalid intermediate translations
riscv: Support BUG() in kernel module
riscv: Add the support for c.ebreak check in is_valid_bugaddr()
riscv: support trap-based WARN()
riscv: fix sbi_remote_sfence_vma{,_asid}.
riscv: move switch_mm to its own file
riscv: move flush_icache_{all,mm} to cacheflush.c
tty: Don't force RISCV SBI console as preferred console
RISC-V: Access CSRs using CSR numbers
RISC-V: Add interrupt related SCAUSE defines in asm/csr.h
RISC-V: Use tabs to align macro values in asm/csr.h
RISC-V: Fix minor checkpatch issues.
RISC-V: Support nr_cpus command line option.
RISC-V: Implement nosmp commandline option.
RISC-V: Add RISC-V specific arch_match_cpu_phys_id
riscv: vdso: drop unnecessary cc-ldoption
riscv: call pm_power_off from machine_halt / machine_power_off
...
The ADX345 supports both I2C & SPI bindings.
This change switches from old text bindings, to YAML bindings, and also
tries to make use of the recent multiple-examples support.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds documentation of a new property phy-dsi-supply to the
STM32 DSI controller.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1557826556-10079-2-git-send-email-yannick.fertre@st.com
Convert the vendor prefix registry to a schema. This will enable checking
that new vendor prefixes are added (in addition to the less than perfect
checkpatch.pl check) and will also check against adding other prefixes
which are not vendors.
Converted vendor-prefixes.txt using the following sed script:
sed -e 's/\([a-zA-Z0-9\-]*\)[[:space:]]*\([a-zA-Z0-9].*\)/ "^\1,\.\*\":\n description: \2/'
Signed-off-by: Rob Herring <robh@kernel.org>
The H3 and compatibles controllers don't have any reception capabilities,
even though it was never documented as such in the binding before.
Therefore, on those controllers, we don't have the option to set an RX DMA
channel.
This was already done in the DTSI, but the binding itself was never
updated. Let's add a special case in the schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Allwinner SoCs feature an SPDIF controller across multiple SoC
generations.
However, earlier generations were a bit simpler than the subsequent ones,
and for example would always have RX and TX capabilities, and no reset
lines.
In order to express this, let's create two YAML schemas instead of the free
form text we had before.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers
-----BEGIN PGP SIGNATURE-----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=YSfu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC
suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
soc: aspeed: fix Kconfig
soc: add aspeed folder and misc drivers
spi: zynqmp: Fix build break
soc: imx: Add generic i.MX8 SoC driver
MAINTAINERS: Update email for Qualcomm SoC maintainer
memory: tegra: Fix a typos for "fdcdwr2" mc client
Revert "ARM: tegra: Restore memory arbitration on resume from LP1 on Tegra30+"
memory: tegra: Replace readl-writel with mc_readl-mc_writel
memory: tegra: Fix integer overflow on tick value calculation
memory: tegra: Fix missed registers values latching
ARM: tegra: cpuidle: Handle tick broadcasting within cpuidle core on Tegra20/30
optee: allow to work without static shared memory
soc/tegra: pmc: Move powergate initialisation to probe
soc/tegra: pmc: Remove reset sysfs entries on error
soc/tegra: pmc: Fix reset sources and levels
soc: amlogic: meson-gx-pwrc-vpu: Add support for G12A
soc: amlogic: meson-gx-pwrc-vpu: Fix power on/off register bitmask
fpga manager: Adding FPGA Manager support for Xilinx zynqmp
dt-bindings: fpga: Add bindings for ZynqMP fpga driver
firmware: xilinx: Add fpga API's
...
SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to multiplatform enabled.
- Cleanups of Davinci
This tag also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release.
-----BEGIN PGP SIGNATURE-----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=pUeO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
Pull thermal soc updates from Eduardo Valentin:
- thermal core has a new devm_* API for registering cooling devices. I
took the entire series, that is why you see changes on drivers/hwmon
in this pull (Guenter Roeck)
- rockchip thermal driver gains support to PX30 SoC (Elaine Zhang)
- the generic-adc thermal driver now considers the lookup table DT
property as optional (Jean-Francois Dagenais)
- Refactoring of tsens thermal driver (Amit Kucheria)
- Cleanups on cpu cooling driver (Daniel Lezcano)
- broadcom thermal driver dropped support to ACPI (Srinath Mannam)
- tegra thermal driver gains support to OC hw throttle and GPU throtle
(Wei Ni)
- Fixes in several thermal drivers.
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (59 commits)
hwmon: (pwm-fan) Use devm_thermal_of_cooling_device_register
hwmon: (npcm750-pwm-fan) Use devm_thermal_of_cooling_device_register
hwmon: (mlxreg-fan) Use devm_thermal_of_cooling_device_register
hwmon: (gpio-fan) Use devm_thermal_of_cooling_device_register
hwmon: (aspeed-pwm-tacho) Use devm_thermal_of_cooling_device_register
thermal: rcar_gen3_thermal: Fix to show correct trip points number
thermal: rcar_thermal: update calculation formula for R-Car Gen3 SoCs
thermal: cpu_cooling: Actually trace CPU load in thermal_power_cpu_get_power
thermal: rockchip: Support the PX30 SoC in thermal driver
dt-bindings: rockchip-thermal: Support the PX30 SoC compatible
thermal: rockchip: fix up the tsadc pinctrl setting error
thermal: broadcom: Remove ACPI support
thermal: Fix build error of missing devm_ioremap_resource on UM
thermal/drivers/cpu_cooling: Remove pointless field
thermal/drivers/cpu_cooling: Add Software Package Data Exchange (SPDX)
thermal/drivers/cpu_cooling: Fixup the header and copyright
thermal/drivers/cpu_cooling: Remove pointless test in power2state()
thermal: rcar_gen3_thermal: disable interrupt in .remove
thermal: rcar_gen3_thermal: fix interrupt type
thermal: Introduce devm_thermal_of_cooling_device_register
...
Add the bindings and the related documentation for the audio hdmitx
control glue of the Amlogic g12a SoC family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge in a few pending fixes from pre-5.1 that didn't get sent in:
MAINTAINERS: update arch/arm/mach-davinci
ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect
ARM: dts: imx6q-logicpd: Reduce inrush current on USBH1
ARM: dts: imx6q-logicpd: Reduce inrush current on start
ARM: dts: imx: Fix the AR803X phy-mode
ARM: dts: sun8i: a33: Reintroduce default pinctrl muxing
arm64: dts: allwinner: a64: Rename hpvcc-supply to cpvdd-supply
ARM: sunxi: fix a leaked reference by adding missing of_node_put
ARM: sunxi: fix a leaked reference by adding missing of_node_put
Signed-off-by: Olof Johansson <olof@lixom.net>
Core:
* Add over-current health state
* Add standard, adaptive and custom charge types
* Add new properties for start/end charge threshold
New Drivers / Hardware:
* UCS1002 Programmable USB Port Power Controller
* Ingenic JZ47xx Battery Fuel Gauge
* AXP20x USB Power: Add AXP813 support
* AT91 poweroff: Add SAM9X60 support
* OLPC battery: Add XO-1.5 and XO-1.75 support
Misc. Changes:
* syscon-reboot: support mask property
* AXP288 fuel gauge: Blacklist ACEPC T8/T11
- Looks like some vendor thought it's a good idea to
build a desktop system with a fuel gauge, that slowly
"discharges"...
* cpcap-battery: Fix calculation errors
* misc. fixes
-----BEGIN PGP SIGNATURE-----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=qicd
-----END PGP SIGNATURE-----
Merge tag 'for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- Add over-current health state
- Add standard, adaptive and custom charge types
- Add new properties for start/end charge threshold
New Drivers / Hardware:
- UCS1002 Programmable USB Port Power Controller
- Ingenic JZ47xx Battery Fuel Gauge
- AXP20x USB Power: Add AXP813 support
- AT91 poweroff: Add SAM9X60 support
- OLPC battery: Add XO-1.5 and XO-1.75 support
Misc Changes:
- syscon-reboot: support mask property
- AXP288 fuel gauge: Blacklist ACEPC T8/T11. Looks like some vendor
thought it's a good idea to build a desktop system with a fuel
gauge, that slowly "discharges"...
- cpcap-battery: Fix calculation errors
- misc fixes"
* tag 'for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (54 commits)
power: supply: olpc_battery: force the le/be casts
power: supply: ucs1002: Fix build error without CONFIG_REGULATOR
power: supply: ucs1002: Fix wrong return value checking
power: supply: Add driver for Microchip UCS1002
dt-bindings: power: supply: Add bindings for Microchip UCS1002
power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant
power: supply: core: fix clang -Wunsequenced
power: supply: core: Add missing documentation for CHARGE_CONTROL_* properties
power: supply: core: Add CHARGE_CONTROL_{START_THRESHOLD,END_THRESHOLD} properties
power: supply: core: Add Standard, Adaptive, and Custom charge types
power: supply: axp288_fuel_gauge: Add ACEPC T8 and T11 mini PCs to the blacklist
power: supply: bq27xxx_battery: Notify also about status changes
power: supply: olpc_battery: Have the framework register sysfs files for us
power: supply: olpc_battery: Add OLPC XO 1.75 support
power: supply: olpc_battery: Avoid using platform_info
power: supply: olpc_battery: Use devm_power_supply_register()
power: supply: olpc_battery: Move priv data to a struct
power: supply: olpc_battery: Use DT to get battery version
x86/platform/olpc: Use a correct version when making up a battery node
x86/platform/olpc: Trivial code move in DT fixup
...
This patch implements the device tree binding changes required for the
PPS ECHO functionality for pps-gpio, that sysfs claims is available
already.
It adds two DT properties for configuring the PPS ECHO functionality.
This patch is provided separated from the rest of the patch per
Documentation/devicetree/bindings/submitting-patches.txt.
This patch was originally written by Lukas Senger as part of a masters
thesis project and modified for inclusion into the linux kernel by Tom
Burkart.
Link: http://lkml.kernel.org/r/20190324043305.6627-3-tom@aussec.com
Signed-off-by: Tom Burkart <tom@aussec.com>
Signed-off-by: Lukas Senger <lukas@fridolin.com>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Document (kerneldoc) core mfd_add_devices() API
- New Drivers
- Add support for Altera SOCFPGA System Manager
- Add support for Maxim MAX77650/77651 PMIC
- Add support for Maxim MAX77663 PMIC
- Add support for ST Multi-Function eXpander (STMFX)
- New Device Support
- Add support for LEDs to Intel Cherry Trail Whiskey Cove PMIC
- Add support for RTC to SAMSUNG Electronics S2MPA01 PMIC
- Add support for SAM9X60 to Atmel HLCDC (High-end LCD Controller)
- Add support for USB X-Powers AXP 8xx PMICs
- Add support for Integrated Sensor Hub (ISH) to ChromeOS EC
- Add support for USB PD Logger to ChromeOS EC
- Add support for AXP223 to X-Powers AXP series PMICs
- Add support for Power Supply to X-Powers AXP 803 PMICs
- Add support for Comet Lake to Intel Low Power Subsystem
- Add support for Fingerprint MCU to ChromeOS EC
- Add support for Touchpad MCU to ChromeOS EC
- Move TI LM3532 support to LED
- New Functionality
- Add/extend DT support; max77650, max77620
- Add support for power-off; max77620
- Add support for clocking; syscon
- Add support for host sleep event; cros_ec
- Fix-ups
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
- Bug Fixes
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio
-----BEGIN PGP SIGNATURE-----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=dTSD
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Document (kerneldoc) core mfd_add_devices() API
New Drivers:
- Altera SOCFPGA System Manager
- Maxim MAX77650/77651 PMIC
- Maxim MAX77663 PMIC
- ST Multi-Function eXpander (STMFX)
New Device Support:
- LEDs support in Intel Cherry Trail Whiskey Cove PMIC
- RTC support in SAMSUNG Electronics S2MPA01 PMIC
- SAM9X60 support in Atmel HLCDC (High-end LCD Controller)
- USB X-Powers AXP 8xx PMICs
- Integrated Sensor Hub (ISH) in ChromeOS EC
- USB PD Logger in ChromeOS EC
- AXP223 in X-Powers AXP series PMICs
- Power Supply in X-Powers AXP 803 PMICs
- Comet Lake in Intel Low Power Subsystem
- Fingerprint MCU in ChromeOS EC
- Touchpad MCU in ChromeOS EC
- Move TI LM3532 support to LED
New Functionality:
- max77650, max77620: Add/extend DT support
- max77620 power-off
- syscon clocking
- croc_ec host sleep event
Fix-ups:
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
Bug Fixes:
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio"
* tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (65 commits)
mfd: Use dev_get_drvdata() directly
mfd: cros_ec: Instantiate properly CrOS Touchpad MCU device
mfd: cros_ec: Instantiate properly CrOS FP MCU device
mfd: cros_ec: Update the EC feature codes
mfd: intel-lpss: Add Intel Comet Lake PCI IDs
mfd: lochnagar: Add links to binding docs for sound and hwmon
mfd: ab8500-debugfs: Fix a typo ("deubgfs")
mfd: imx6sx: Add MQS register definition for iomuxc gpr
dt-bindings: mfd: LMU: Fix lm3632 dt binding example
mfd: intel_quark_i2c_gpio: Adjust IOT2000 matching
mfd: da9063: Fix OTP control register names to match datasheets for DA9063/63L
mfd: tps65912-spi: Add missing of table registration
mfd: axp20x: Add USB power supply mfd cell to AXP803
mfd: sun6i-prcm: Fix build warning for non-OF configurations
mfd: intel-lpss: Set the device in reset state when init
platform/chrome: Add support for v1 of host sleep event
mfd: cros_ec: Add host_sleep_event_v1 command
mfd: cros_ec: Instantiate the CrOS USB PD logger driver
mfd: cs47l90: Make DAC_AEC_CONTROL_2 readable
mfd: cs47l35: Make DAC_AEC_CONTROL_2 readable
...
Add a new compatible for thermal founding on PX30 SoCs.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
qcs404 uses v1 of the TSENS IP block. Create a fallback DT property
"qcom,tsens-v1" to gather common code
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add new backlight bindings for the TI LM3630A dual-string white LED.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
Add links to the binding documents for the new sound and hardware
monitor parts of the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix the lm3632 dt binding examples as the LCM enable GPIOs
are defined as enable GPIOs per the regulator/lm363x-regulator.txt
bindings document.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add new compatible string for the HLCD controller on SAM9X60 SoC.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
STM32 system configuration controller registers needs to be clocked.
Document clock support on stm32-syscon.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----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=55X1
-----END PGP SIGNATURE-----
Merge branches 'ib-mfd-arm-leds-5.2', 'ib-mfd-gpio-input-leds-power-5.2', 'ib-mfd-pinctrl-5.2-2' and 'ib-mfd-regulator-5.2', tag 'ib-mfd-arm-net-5.2' into ibs-for-mfd-merged
Immutable branch between MFD, ARM and Net due for the 5.2 merge window
Add OC HW throttle configuration for soctherm in DT.
It is used to describe the OCx throttle events.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add optional property "nvidia,thermtrips".
If present, these trips will be used as HW shutdown trips,
and critical trips will be used as SW shutdown trips.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
- Move IRQ register address computation inside macros (Kishon Vijay
Abraham I)
- Separate legacy IRQ and MSI configuration (Kishon Vijay Abraham I)
- Use hwirq, not virq, to get MSI IRQ number offset (Kishon Vijay Abraham
I)
- Squash ks_pcie_handle_msi_irq() into ks_pcie_msi_irq_handler() (Kishon
Vijay Abraham I)
- Add dwc support for platforms with custom MSI controllers (Kishon Vijay
Abraham I)
- Add keystone-specific MSI controller (Kishon Vijay Abraham I)
- Remove dwc host_ops previously used for keystone-specific MSI (Kishon
Vijay Abraham I)
- Skip dwc default MSI init if platform has custom MSI controller (Kishon
Vijay Abraham I)
- Implement .start_link() and .stop_link() for keystone endpoint support
(Kishon Vijay Abraham I)
- Add keystone "reg-names" DT binding (Kishon Vijay Abraham I)
- Squash ks_pcie_dw_host_init() into ks_pcie_add_pcie_port() (Kishon
Vijay Abraham I)
- Get keystone register resources from DT by name, not index (Kishon
Vijay Abraham I)
- Get DT resources in .probe() to prepare for endpoint support (Kishon
Vijay Abraham I)
- Add "ti,syscon-pcie-mode" DT property for PCIe mode configuration
(Kishon Vijay Abraham I)
- Explicitly set keystone to host mode (Kishon Vijay Abraham I)
- Document DT "atu" reg-names requirement for DesignWare core >= 4.80
(Kishon Vijay Abraham I)
- Enable dwc iATU unroll for endpoint mode as well as host mode (Kishon
Vijay Abraham I)
- Add dwc "version" to identify core >= 4.80 for ATU programming (Kishon
Vijay Abraham I)
- Don't build ARM32-specific keystone code on ARM64 (Kishon Vijay Abraham
I)
- Add DT binding for keystone PCIe RC in AM654 SoC (Kishon Vijay Abraham
I)
- Add keystone support for AM654 SoC PCIe RC (Kishon Vijay Abraham I)
- Reset keystone PHYs before enabling them (Kishon Vijay Abraham I)
- Make of_pci_get_max_link_speed() available to endpoint drivers as well
as host drivers (Kishon Vijay Abraham I)
- Add keystone support for DT "max-link-speed" property (Kishon Vijay
Abraham I)
- Add endpoint library support for BAR buffer alignment (Kishon Vijay
Abraham I)
- Make all dw_pcie_ep_ops structs const (Kishon Vijay Abraham I)
- Fix fencepost error in dw_pcie_ep_find_capability() (Kishon Vijay
Abraham I)
- Add dwc hooks for dbi/dbi2 that share the same address space (Kishon
Vijay Abraham I)
- Add keystone support for TI AM654x in endpoint mode (Kishon Vijay
Abraham I)
- Configure designware endpoints to advertise smallest resizable BAR
(1MB) (Kishon Vijay Abraham I)
- Align designware endpoint ATU windows for raising MSIs (Kishon Vijay
Abraham I)
- Add endpoint test support for TI AM654x (Kishon Vijay Abraham I)
- Fix endpoint test test_reg_bar issue (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
misc: pci_endpoint_test: Fix test_reg_bar to be updated in pci_endpoint_test
misc: pci_endpoint_test: Add support to test PCI EP in AM654x
PCI: designware-ep: Use aligned ATU window for raising MSI interrupts
PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size
PCI: keystone: Add support for PCIe EP in AM654x Platforms
dt-bindings: PCI: Add PCI EP DT binding documentation for AM654
PCI: dwc: Add callbacks for accessing dbi2 address space
PCI: dwc: Fix dw_pcie_ep_find_capability() to return correct capability offset
PCI: dwc: Add const qualifier to struct dw_pcie_ep_ops
PCI: endpoint: Add support to specify alignment for buffers allocated to BARs
PCI: keystone: Add support to set the max link speed from DT
PCI: OF: Allow of_pci_get_max_link_speed() to be used by PCI Endpoint drivers
PCI: keystone: Invoke phy_reset() API before enabling PHY
PCI: keystone: Add support for PCIe RC in AM654x Platforms
dt-bindings: PCI: Add PCI RC DT binding documentation for AM654
PCI: keystone: Prevent ARM32 specific code to be compiled for ARM64
PCI: dwc: Fix ATU identification for designware version >= 4.80
PCI: dwc: Enable iATU unroll for endpoint too
dt-bindings: PCI: Document "atu" reg-names
PCI: keystone: Explicitly set the PCIe mode
dt-bindings: PCI: Add dt-binding to configure PCIe mode
PCI: keystone: Move resources initialization to prepare for EP support
PCI: keystone: Use platform_get_resource_byname() to get memory resources
PCI: keystone: Perform host initialization in a single function
dt-bindings: PCI: keystone: Add "reg-names" binding information
PCI: keystone: Cleanup error_irq configuration
PCI: keystone: Add start_link()/stop_link() dw_pcie_ops
PCI: dwc: Remove default MSI initialization for platform specific MSI chips
PCI: dwc: Remove Keystone specific dw_pcie_host_ops
PCI: keystone: Use Keystone specific msi_irq_chip
PCI: dwc: Add support to use non default msi_irq_chip
PCI: keystone: Cleanup ks_pcie_msi_irq_handler()
PCI: keystone: Use hwirq to get the MSI IRQ number offset
PCI: keystone: Add separate functions for configuring MSI and legacy interrupt
PCI: keystone: Cleanup interrupt related macros
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.h
Pull input updates from Dmitry Torokhov:
"A few new drivers:
- driver for Azoteq IQS550/572/525 touch controllers
- driver for Microchip AT42QT1050 keys
- driver for GPIO controllable vibrators
- support for GT5663 in Goodix driver
... along with miscellaneous driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: libps2 - mark expected switch fall-through
Input: qt1050 - add Microchip AT42QT1050 support
Input: add support for Azoteq IQS550/572/525
Input: add a driver for GPIO controllable vibrators
Input: synaptics-rmi4 - fix enum_fmt
Input: synaptics-rmi4 - fill initial format
HID: input: add mapping for KEY_KBD_LAYOUT_NEXT
Input: add KEY_KBD_LAYOUT_NEXT
Input: hyperv-keyboard - add module description
Input: olpc_apsp - depend on ARCH_MMP
Input: sun4i-a10-lradc-keys - add support for A83T
Input: snvs_pwrkey - use dev_pm_set_wake_irq() to simplify code
Input: lpc32xx-key - add clocks property and fix DT binding example
Input: i8042 - signal wakeup from atkbd/psmouse
Input: goodix - add GT5663 CTP support
Input: goodix - add regulators suppot
Input: evdev - use struct_size() in kzalloc() and vzalloc()
Input: edt-ft5x06 - convert to use SPDX identifier
Input: edt-ft5x06 - enable ACPI enumeration
Pull networking fixes from David Miller:
"Fixes all over:
1) Netdev refcnt leak in nf_flow_table, from Taehee Yoo.
2) Fix RCU usage in nf_tables, from Florian Westphal.
3) Fix DSA build when NET_DSA_TAG_BRCM_PREPEND is not set, from Yue
Haibing.
4) Add missing page read/write ops to realtek driver, from Heiner
Kallweit.
5) Endianness fix in qrtr code, from Nicholas Mc Guire.
6) Fix various bugs in DSA_SKB_* macros, from Vladimir Oltean.
7) Several BPF documentation cures, from Quentin Monnet.
8) Fix undefined behavior in narrow load handling of BPF verifier,
from Krzesimir Nowak.
9) DMA ops crash in SGI Seeq driver due to not set netdev parent
device pointer, from Thomas Bogendoerfer.
10) Flow dissector has to disable preemption when invoking BPF
program, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (48 commits)
net: ethernet: stmmac: dwmac-sun8i: enable support of unicast filtering
net: ethernet: ti: netcp_ethss: fix build
flow_dissector: disable preemption around BPF calls
bonding: fix arp_validate toggling in active-backup mode
net: meson: fixup g12a glue ephy id
net: phy: realtek: Replace phy functions with non-locked version in rtl8211e_config_init()
net: seeq: fix crash caused by not set dev.parent
of_net: Fix missing of_find_device_by_node ref count drop
net: mvpp2: cls: Add missing NETIF_F_NTUPLE flag
bpf: fix undefined behavior in narrow load handling
libbpf: detect supported kernel BTF features and sanitize BTF
selftests: bpf: Add files generated after build to .gitignore
tools: bpf: synchronise BPF UAPI header with tools
bpf: fix minor issues in documentation for BPF helpers.
bpf: fix recurring typo in documentation for BPF helpers
bpf: fix script for generating man page on BPF helpers
bpf: add various test cases for backward jumps
net: dccp : proto: remove Unneeded variable "err"
net: dsa: Remove the now unused DSA_SKB_CB_COPY() macro
net: dsa: Remove dangerous DSA_SKB_CLONE() macro
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAlzZRp0ACgkQ+iyteGJfRsq1WQCfaR8jQjujN1bGWghnSWbTr01X
O3cAn3RmJWiEtI0zmmMcRQBna8nj4cHJ
=PuHw
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-5.2-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- a new watchdog driver for the ROHM BD70528 watchdog block
- a new watchdog driver for the i.MX system controller watchdog
- conversions to use device managed functions and other improvements
- refactor watchdog_init_timeout
- make watchdog core configurable as module
- pretimeout governors improvements
- a lot of other fixes
* tag 'linux-watchdog-5.2-rc1' of git://www.linux-watchdog.org/linux-watchdog: (114 commits)
watchdog: Enforce that at least one pretimeout governor is enabled
watchdog: stm32: add dynamic prescaler support
watchdog: Improve Kconfig entry ordering and dependencies
watchdog: npcm: Enable modular builds
watchdog: Make watchdog core configurable as module
watchdog: Move pretimeout governor configuration up
watchdog: Use depends instead of select for pretimeout governors
watchdog: rtd119x: drop unused module.h include
watchdog: intel_scu: make it explicitly non-modular
watchdog: coh901327: make it explicitly non-modular
watchdog: ziirave_wdt: drop warning after calling watchdog_init_timeout
watchdog: xen_wdt: drop warning after calling watchdog_init_timeout
watchdog: stm32_iwdg: drop warning after calling watchdog_init_timeout
watchdog: st_lpc_wdt: drop warning after calling watchdog_init_timeout
watchdog: sp5100_tco: drop warning after calling watchdog_init_timeout
watchdog: renesas_wdt: drop warning after calling watchdog_init_timeout
watchdog: nic7018_wdt: drop warning after calling watchdog_init_timeout
watchdog: ni903x_wdt: drop warning after calling watchdog_init_timeout
watchdog: imx_sc_wdt: drop warning after calling watchdog_init_timeout
watchdog: i6300esb: drop warning after calling watchdog_init_timeout
...
Add device tree binding information for slg51000 regulator driver.
Example bindings for SLG51000 are added.
Signed-off-by: Eric Jeong <eric.jeong.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
* Avoid crossing 4K address boundary on read/write
* Add support for Intel Comet Lake SPI serial flash
-----BEGIN PGP SIGNATURE-----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=HXap
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from
generic functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
- Switch to ->exec-op().
- meson:
- Misc cleanups and fixes.
- New OOB layout.
- Sunxi:
- A23/A33 NAND DMA support.
- Ingenic:
- Full reorganization and cleanup.
- Clear separation between NAND controller and ECC engine.
- Support JZ4740 an JZ4725B.
- Denali:
- Clear controller/chip separation.
- ->exec_op() migration.
- Various cleanups.
- fsl_elbc:
- Enable software ECC support.
- Atmel:
- Sam9x60 support.
- GPMI:
- Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
- Avoid crossing 4K address boundary on read/write
- Add support for Intel Comet Lake SPI serial flash"
* tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (120 commits)
mtd: part: fix incorrect format specifier for an unsigned long long
mtd: lpddr_cmds: Mark expected switch fall-through
mtd: phram: Mark expected switch fall-throughs
mtd: cfi_cmdset_0002: Mark expected switch fall-throughs
mtd: cfi_util: mark expected switch fall-throughs
MAINTAINERS: MTD Git repository is hosted on kernel.org
MAINTAINERS: Update jffs2 entry
mtd: afs: add v2 partition parsing
mtd: afs: factor the IIS read into partition parser
mtd: afs: factor footer parsing into the v1 part parsing
mtd: factor out v1 partition parsing
mtd: afs: simplify partition detection
mtd: afs: simplify partition parsing
mtd: partitions: Add OF support to AFS partitions
mtd: partitions: Add AFS partitions DT bindings
mtd: afs: Move AFS partition parser to parsers subdir
mtd: maps: Make uclinux_ram_map static
mtd: maps: Allow MTD_PHYSMAP with MTD_RAM
MAINTAINERS: Add myself as MTD maintainer
MAINTAINERS: Remove my name from the MTD and NAND entries
...
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to
be handled consistently. Unsurprisingly, we enforce the lines to
be either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone
does, so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed.
Such nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs
and outputs at the same time and after improving the MMIO library
we handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM
work as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update.
-----BEGIN PGP SIGNATURE-----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=rhto
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v5.2 kernel cycle. A bit
later than usual because I was ironing out my own mistakes. I'm
holding some stuff back for the next kernel as a result, and this
should be a healthy and well tested batch.
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to be
handled consistently. Unsurprisingly, we enforce the lines to be
either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone does,
so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed. Such
nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs and
outputs at the same time and after improving the MMIO library we
handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM work
as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update"
* tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: Update documentation
docs: gpio: convert docs to ReST and rename to *.rst
gpio: sch: Remove write-only core_base
gpio: pxa: Make two symbols static
gpiolib: acpi: Respect pin bias setting
gpiolib: acpi: Add acpi_gpio_update_gpiod_lookup_flags() helper
gpiolib: acpi: Set pin value, based on bias, more accurately
gpiolib: acpi: Change type of dflags
gpiolib: Introduce GPIO_LOOKUP_FLAGS_DEFAULT
gpiolib: Make use of enum gpio_lookup_flags consistent
gpiolib: Indent entry values of enum gpio_lookup_flags
gpio: pca953x: add support for pca6416
dt-bindings: gpio: pca953x: document the nxp,pca6416
gpio: pca953x: add pcal6416 to the of_device_id table
gpio: gpio-omap: Remove conditional pm_runtime handling for GPIO interrupts
gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup
tracing: stop making gpio tracing configurable
gpio: pca953x: Configure wake-up path when wake-up is enabled
gpio: of: Optimize quirk checks
gpio: mmio: Drop bgpio_dir_inverted
...
In commit 687e3d5550 ("dt-bindings: doc: reflect new NVMEM
of_get_mac_address behaviour") I've kept or added references to Linux
of_get_mac_address API which is unwanted so this patch fixes that by
removing those references.
Fixes: 687e3d5550 ("dt-bindings: doc: reflect new NVMEM of_get_mac_address behaviour")
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=hAkf
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-gpio-input-leds-power-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into next
Sync up with MFD tree to bring in MAX77650 PMIC driver.
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlzPgx4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGf8IH/jkes7tKj7pWfsNW
uMjbm5T+Jh26sntRj+3OWOxcHRlejTH2MammnA9GIspBfF5LXkkmk40eeYhnTiVN
SzZqSFNLO0tRIHsd7hbxhTyOzHcWmymoEqY1jb8IPMyM5BB8TiS+1C0AVlOW1P/f
TO1gRcrddu1j80uCInRzNX5eAlvfrU4nK6GxjFdmy6b/bgYQiPfNA+jZbCWxc+48
ivBn9ifFCKlDzki81Dmi5R98c4R9UU3Z5LsqHjC4RIV64hpHdEwnOIkXQ+XY5mW9
7EOT1v6hJGch1ulH27ypgSZ7fhSCSYQJIY/LNWeJtdVclvlVepb2Vrx/8NUN60qC
E0MEn1Y=
=mCkr
-----END PGP SIGNATURE-----
Merge tag 'v5.1' into next
Sync up with mainline to bring in the latest APIs.
Nothing out of the ordinary this cycle. The bulk of this is a collection
of fixes for existing drivers and some cleanups. There's one new driver
for i.MX SoCs and addition of support for some new variants to existing
drivers.
-----BEGIN PGP SIGNATURE-----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=3p6h
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.2-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Nothing out of the ordinary this cycle.
The bulk of this is a collection of fixes for existing drivers and
some cleanups. There's one new driver for i.MX SoCs and addition of
support for some new variants to existing drivers"
* tag 'pwm/for-5.2-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: meson: Add clock source configuration for Meson G12A
dt-bindings: pwm: Update bindings for the Meson G12A Family
pwm: samsung: Don't uses devm_*() functions in ->request()
pwm: Clear chip_data in pwm_put()
pwm: Add i.MX TPM PWM driver support
dt-bindings: pwm: Add i.MX TPM PWM binding
pwm: imx27: Use devm_platform_ioremap_resource() to simplify code
pwm: meson: Use the spin-lock only to protect register modifications
pwm: meson: Don't disable PWM when setting duty repeatedly
pwm: meson: Consider 128 a valid pre-divider
pwm: sysfs: fix typo "its" -> "it's"
pwm: tiehrpwm: Enable compilation for ARCH_K3
dt-bindings: pwm: tiehrpwm: Add TI AM654 SoC specific compatible
pwm: tiehrpwm: Update shadow register for disabling PWMs
pwm: img: Turn final 'else if' into 'else' in img_pwm_config
pwm: Fix deadlock warning when removing PWM device
- Misc: Use devm_ api for imx and platform_get_irq for stm32
-----BEGIN PGP SIGNATURE-----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=rUxA
-----END PGP SIGNATURE-----
Merge tag 'mailbox-v5.2' of git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- New driver: Armada 37xx mailbox controller
- Misc: Use devm_ api for imx and platform_get_irq for stm32
* tag 'mailbox-v5.2' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: Add support for Armada 37xx rWTM mailbox
dt-bindings: mailbox: Document armada-3700-rwtm-mailbox binding
mailbox: stm32-ipcc: check invalid irq
mailbox: imx: use devm_platform_ioremap_resource() to simplify code
This patch adds documentation of device tree bindings for the
STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds documentation of device tree bindings for the
STMicroelectronics Multi-Function eXpander (STMFX) MFD core.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
around because we've finally gotten around to fixing some long standing issues.
There's still work to do though, so this PR is largely laying down the
foundation for all the driver changes to come in the next merge window.
The first problem we're alleviating is how parents of clks are specified. With
the new method, we should see lots of drivers migrate away from the current
design of string comparisons on the entire clk tree to a more direct method
where they can use clk_hw pointers or more localized names specified in DT or
via clkdev. This should reduce our reliance on string comparisons for all the
topology description logic that we've been using for years and hopefully speed
some things up while avoiding problems we have with generating clk names.
Beyond that we also got rid of the CLK_IS_BASIC flag because it wasn't really
helping anyone and we introduced big-endian versions of the basic clk types so
that we can get rid of clk_{readl,writel}(). Both of these are things that
driver developers have tried to use over the years that I typically bat away
during code reviews because they're not useful. It's great to see these two
things go away so maintainers can save time not worrying about these things.
On the driver side we got the usual collection of new SoC support and
non-critical fixes and updates to existing code. The big topics that stand out
are the new driver support for Mediatek MT8183 and MT8516 SoCs, Amlogic Meson8b
and G12a SoCs, and the SiFive FU540 SoC. The other patches in the driver pile
are mostly fixes for things that are being used for the first time or additions
for clks that couldn't be tested before because there wasn't a consumer driver
that exercised them. Details are below and also in the sub-maintainer tags.
Core:
- Remove clk_readl() and introduce BE versions of basic clk types
- Rewrite how clk parents can be specified to allow DT/clkdev lookups
- Removal of the CLK_IS_BASIC clk flag
- Framework documentation updates and fixes
New Drivers:
- Support for STM32F769
- AT91 sam9x60 PMC support
- SiFive FU540 PRCI and PLL support
- Qualcomm QCS404 CDSP clk support
- Qualcomm QCS404 Turing clk support
- Mediatek MT8183 clock support
- Mediatek MT8516 clock support
- Milbeaut M10V clk controller support
- Support for Cirrus Logic Lochnagar clks
Updates:
- Rework AT91 sckc DT bindings
- Fix slow RC oscillator issue on sama5d3
- Mark UFS clk as critical on Hi-Silicon hi3660 SoCs
- Various static analysis fixes/finds and const markings
- Video Engine (ECLK) support on Aspeed SoCs
- Xilinx ZynqMP Versal platform support
- Convert Xilinx ZynqMP driver to be struct oriented
- Fixes for Rockchip rk3328 and rk3288 SoCs
- Sub-type for Rockchip SoCs where mux and divider aren't a single register
- Remove SNVS clock from i.MX7UPL clock driver and bindings
- Improve i.MX5 clock driver for i.MX50 support
- Addition of ADC clock definition for Exynos 5410 SoC (Odroid XU)
- Export a new clock for the MBUS controller on the A13
- Allwinner H6 fixes to support a finer clocking of the video and VPU engines
- Add g12a support in the Amlogic axg audio clock controller
- Add missing PCI USB clock on Rensas RZ/N1
- Add Z2 (Cortex-A53) clocks on Rensas R-Car E3 and RZ/G2E
- A new helper DIV64_U64_ROUND_CLOSEST() in <linux/math64.h>
- VPU and Video Decoder clocks on Amlogic Meson8b
- Finally remove the wrong ABP Meson8b clock id
- Add Video Decoder, PCIe PLL, and CPU Clocks on Amlogic G12A
- Re-expose SAR_ADC_SEL and CTS_OSCIN on Amlogic G12A AO clock controller
- Un-expose some Amlogic AXG-Audio input clocks IDs
-----BEGIN PGP SIGNATURE-----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=/uso
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk framework updates from Stephen Boyd:
"We have a couple new features and changes in the core clk framework
this time around because we've finally gotten around to fixing some
long standing issues. There's still work to do though, so this pull
request is largely laying down the foundation for all the driver
changes to come in the next merge window.
The first problem we're alleviating is how parents of clks are
specified. With the new method, we should see lots of drivers migrate
away from the current design of string comparisons on the entire clk
tree to a more direct method where they can use clk_hw pointers or
more localized names specified in DT or via clkdev. This should reduce
our reliance on string comparisons for all the topology description
logic that we've been using for years and hopefully speed some things
up while avoiding problems we have with generating clk names.
Beyond that we also got rid of the CLK_IS_BASIC flag because it wasn't
really helping anyone and we introduced big-endian versions of the
basic clk types so that we can get rid of clk_{readl,writel}(). Both
of these are things that driver developers have tried to use over the
years that I typically bat away during code reviews because they're
not useful. It's great to see these two things go away so maintainers
can save time not worrying about these things.
On the driver side we got the usual collection of new SoC support and
non-critical fixes and updates to existing code. The big topics that
stand out are the new driver support for Mediatek MT8183 and MT8516
SoCs, Amlogic Meson8b and G12a SoCs, and the SiFive FU540 SoC. The
other patches in the driver pile are mostly fixes for things that are
being used for the first time or additions for clks that couldn't be
tested before because there wasn't a consumer driver that exercised
them. Details are below and also in the sub-maintainer tags.
Core:
- Remove clk_readl() and introduce BE versions of basic clk types
- Rewrite how clk parents can be specified to allow DT/clkdev lookups
- Removal of the CLK_IS_BASIC clk flag
- Framework documentation updates and fixes
New Drivers:
- Support for STM32F769
- AT91 sam9x60 PMC support
- SiFive FU540 PRCI and PLL support
- Qualcomm QCS404 CDSP clk support
- Qualcomm QCS404 Turing clk support
- Mediatek MT8183 clock support
- Mediatek MT8516 clock support
- Milbeaut M10V clk controller support
- Support for Cirrus Logic Lochnagar clks
Updates:
- Rework AT91 sckc DT bindings
- Fix slow RC oscillator issue on sama5d3
- Mark UFS clk as critical on Hi-Silicon hi3660 SoCs
- Various static analysis fixes/finds and const markings
- Video Engine (ECLK) support on Aspeed SoCs
- Xilinx ZynqMP Versal platform support
- Convert Xilinx ZynqMP driver to be struct oriented
- Fixes for Rockchip rk3328 and rk3288 SoCs
- Sub-type for Rockchip SoCs where mux and divider aren't a single register
- Remove SNVS clock from i.MX7UPL clock driver and bindings
- Improve i.MX5 clock driver for i.MX50 support
- Addition of ADC clock definition for Exynos 5410 SoC (Odroid XU)
- Export a new clock for the MBUS controller on the A13
- Allwinner H6 fixes to support a finer clocking of the video and VPU engines
- Add g12a support in the Amlogic axg audio clock controller
- Add missing PCI USB clock on Rensas RZ/N1
- Add Z2 (Cortex-A53) clocks on Rensas R-Car E3 and RZ/G2E
- A new helper DIV64_U64_ROUND_CLOSEST() in <linux/math64.h>
- VPU and Video Decoder clocks on Amlogic Meson8b
- Finally remove the wrong ABP Meson8b clock id
- Add Video Decoder, PCIe PLL, and CPU Clocks on Amlogic G12A
- Re-expose SAR_ADC_SEL and CTS_OSCIN on Amlogic G12A AO clock controller
- Un-expose some Amlogic AXG-Audio input clocks IDs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (172 commits)
clk: Cache core in clk_fetch_parent_index() without names
clk: imx: correct pfdv2 gate_bit/vld_bit operations
clk: sifive: add a driver for the SiFive FU540 PRCI IP block
clk: analogbits: add Wide-Range PLL library
clk: imx: clk-pllv3: mark expected switch fall-throughs
clk: imx8mq: Add dsi_ipg_div
clk: imx: pllv4: add fractional-N pll support
clk: sunxi-ng: Use the correct style for SPDX License Identifier
clk: sprd: Use the correct style for SPDX License Identifier
clk: renesas: Use the correct style for SPDX License Identifier
clk: qcom: Use the correct style for SPDX License Identifier
clk: davinci: Use the correct style for SPDX License Identifier
clk: actions: Use the correct style for SPDX License Identifier
clk: imx: keep uart clock on during system boot
clk: imx: correct i.MX7D AV PLL num/denom offset
dt-bindings: clk: add documentation for the SiFive PRCI driver
clk: stm32mp1: Add ddrperfm clock
clk: Remove CLK_IS_BASIC clk flag
clock: milbeaut: Add Milbeaut M10V clock controller
dt-bindings: clock: milbeaut: add Milbeaut clock description
...
Subsystem:
- set_mmss and set_mmss64 rtc_ops removal
- Fix timestamp value for RTC_TIMESTAMP_BEGIN_1900
- Use SPDX identifier for the core
- validate upper bound of tm->tm_year
New driver:
- Aspeed BMC SoC RTC
Drivers:
- abx80x: use rtc_add_group
- ds3232: nvram support
- pcf85063: add alarm, nvram, offset correction and microcrystal rv8263 support
- x1205: add of_match_table
- Use set_time instead of set_mms/set_mmss64 for: ab3100, coh901331, digicolor,
ds1672, ds2404, ep93xx, imxdi, jz4740, lpc32xx, mc13xxx, mxc, pcap, stmp3xxx,
test, wm831x, xgene.
- Set RTC range for: ab3100, at91sam9, coh901331, da9063, digicolor, dm355evm,
ds1672, ds2404, ep39xx, goldfish, imxdi, jz4740, lpc32xx, mc13xxx, mv, mxc,
omap, pcap, pcf85063, pcf85363, ps3, sh, stmp3xxx, sun4v, tegra, wm831x,
xgene.
- Switch to rtc_time64_to_tm/rtc_tm_to_time64 for the driver that properly set
the RTC range.
- Use dev_get_drvdata instead of multiple indirections.
-----BEGIN PGP SIGNATURE-----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=NyAx
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"A huge series from me this cycle. I went through many drivers to set
the date and time range supported by the RTC which helps solving HW
limitation when the time comes (as early as next year for some). This
time, I focused on drivers using .set_mms and .set_mmss64, allowing me
to remove those callbacks. About a third of the patches got reviews, I
actually own the RTCs and I tested another third and the remaining one
are unlikely to cause any issues.
Other than that, a single new driver and the usual fixes here and there.
Summary:
Subsystem:
- set_mmss and set_mmss64 rtc_ops removal
- Fix timestamp value for RTC_TIMESTAMP_BEGIN_1900
- Use SPDX identifier for the core
- validate upper bound of tm->tm_year
New driver:
- Aspeed BMC SoC RTC
Drivers:
- abx80x: use rtc_add_group
- ds3232: nvram support
- pcf85063: add alarm, nvram, offset correction and microcrystal
rv8263 support
- x1205: add of_match_table
- Use set_time instead of set_mms/set_mmss64 for: ab3100, coh901331,
digicolor, ds1672, ds2404, ep93xx, imxdi, jz4740, lpc32xx, mc13xxx,
mxc, pcap, stmp3xxx, test, wm831x, xgene.
- Set RTC range for: ab3100, at91sam9, coh901331, da9063, digicolor,
dm355evm, ds1672, ds2404, ep39xx, goldfish, imxdi, jz4740, lpc32xx,
mc13xxx, mv, mxc, omap, pcap, pcf85063, pcf85363, ps3, sh,
stmp3xxx, sun4v, tegra, wm831x, xgene.
- Switch to rtc_time64_to_tm/rtc_tm_to_time64 for the driver that
properly set the RTC range.
- Use dev_get_drvdata instead of multiple indirections"
* tag 'rtc-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (177 commits)
rtc: snvs: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
rtc: imxdi: remove unused variable
rtc: drop set_mms and set_mmss64
rtc: pcap: convert to SPDX identifier
rtc: pcap: use .set_time
rtc: pcap: switch to rtc_time64_to_tm/rtc_tm_to_time64
rtc: pcap: set range
rtc: digicolor: convert to SPDX identifier
rtc: digicolor: use .set_time
rtc: digicolor: set range
rtc: digicolor: fix possible race condition
rtc: jz4740: convert to SPDX identifier
rtc: jz4740: rework invalid time detection
rtc: jz4740: use dev_pm_set_wake_irq() to simplify code
rtc: jz4740: use .set_time
rtc: jz4740: remove useless check
rtc: jz4740: switch to rtc_time64_to_tm/rtc_tm_to_time64
rtc: jz4740: set range
rtc: 88pm860x: prevent use-after-free on device remove
rtc: Use dev_get_drvdata()
...
Pull i2c updates from Wolfram Sang:
- API for late atomic transfers (e.g. to shut down via PMIC). We have a
seperate callback now which is called under clearly defined
conditions. In-kernel users are converted, too.
- new driver for the AMD PCIe MP2 I2C controller
- large refactoring for at91 and bcm-iproc (both gain slave support due
to this)
- and a good share of various driver improvements anf fixes
* 'i2c/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (57 commits)
dt-bindings: i2c: riic: document r7s9210 support
i2c: imx-lpi2c: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
i2c-piix4: Add Hygon Dhyana SMBus support
i2c: core: apply 'is_suspended' check for SMBus, too
i2c: core: ratelimit 'transfer when suspended' errors
i2c: iproc: Change driver to use 'BIT' macro
i2c: riic: Add Runtime PM support
i2c: mux: demux-pinctrl: use struct_size() in devm_kzalloc()
i2c: mux: pca954x: allow management of device idle state via sysfs
i2c: mux: pca9541: remove support for unused platform data
i2c: mux: pca954x: remove support for unused platform data
dt-bindings: i2c: i2c-mtk: add support for MT8516
i2c: axxia: use auto cmd for last message
i2c: gpio: flag atomic capability if possible
i2c: algo: bit: add flag to whitelist atomic transfers
i2c: stu300: use xfer_atomic callback to bail out early
i2c: ocores: enable atomic xfers
i2c: ocores: refactor setup for polling
i2c: tegra-bpmp: convert to use new atomic callbacks
i2c: omap: Add the master_xfer_atomic hook
...
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and
support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips
and support for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma,
rcar-dmac, stm32-dma etc
- dev_get_drvdata() updates on few drivers
-----BEGIN PGP SIGNATURE-----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=JDU6
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips and support
for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma, rcar-dmac,
stm32-dma etc
- dev_get_drvdata() updates on few drivers
* tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (34 commits)
dmaengine: tegra210-adma: restore channel status
dmaengine: tegra210-dma: free dma controller in remove()
dmaengine: tegra210-adma: add pause/resume support
dmaengine: tegra210-adma: add support for Tegra186/Tegra194
Documentation: DT: Add compatibility binding for Tegra186
dmaengine: tegra210-adma: prepare for supporting newer Tegra chips
dmaengine: at_xdmac: remove a stray bottom half unlock
dmaengine: fsl-edma: Adjust indentation
dmaengine: fsl-edma: Fix typo in Vybrid name
dmaengine: stm32-dma: fix residue calculation in stm32-dma
dmaengine: nbpfaxi: Use dev_get_drvdata()
dmaengine: bcm-sba-raid: Use dev_get_drvdata()
dmaengine: stm32-dma: Fix unsigned variable compared with zero
dmaengine: stm32-dma: use platform_get_irq()
dmaengine: rcar-dmac: Update copyright information
dmaengine: imx-sdma: Only check ratio on parts that support 1:1
dmaengine: xgene-dma: fix spelling mistake "descripto" -> "descriptor"
dmaengine: idma64: Move driver name to the header
dmaengine: bcm2835: Drop duplicate capability setting.
dmaengine: pl330: _stop: clear interrupt status
...
Update the doc to explicitly support Meson G12A Family.
The 2 first (A & B) AO PWM uses different clock source than the last 2
(C & D) AO PWM modules, thus we need to differentiate them.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The most significant changes at this cycle are the Sound Open Firmware
support from Intel for the common DSP framework along with its support
for Intel platforms. It's a door opened to a real "free" firmware (in
the sense of FOSS), and other parties show interests in it.
In addition to SOF, we've got a bunch of updates and fixes as usual.
Some highlights are below.
ALSA core:
- Cleanups and fixes in ALSA timer code to cover some races spotted
by syzkaller
- Cleanups and fixes in ALSA sequencer code to cover some races,
again unsurprisingly, spotted by syzkaller
- Optimize the common page allocation helper with alloc_pages_exact()
ASoC:
- Add SOF core support, as well as Intel SOF platform support
- Generic card driver improvements: support for MCLK/sample rate
ratio and pin switches
- A big set of improvements to TLV320AIC32x4 drivers
- New drivers for Freescale audio mixers, several Intel machines,
several Mediatek machines, Meson G12A, Spreadtrum compressed audio
and DMA devices
HD-audio:
- A few Realtek codec fixes for reducing pop noises
- Quirks for Chromebooks
- Workaround for faulty connection report on AMD/Nvidia HDMI
Others:
- A quirk for Focusrite Scarlett Solo USB-audio
- Add support for MOTU 8pre FireWire
- 24bit sample format support in aloop
- GUS patch format support (finally, over a decade) in native
emux synth code
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAlzUKVAOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE/FtQ/+LWWV9wIXeKYCSxKUdUF21Cpdo9eh3P55MTIR
ooxbasNywsllYC1l2IXYi/HYKUlpIwg7kA2itfxaPSW7pveWKPt4mufJsvWpRZws
XUre1MPR9vzTwDqhiG+8rH3osS0YVu9kOipRej043hFHsnXxbOfsnSQ2I+tst6tS
12s5Hmhx/YFyR6fJMCIm3CoR59spz/SWXftna6bnkKbEYkeDmI3TtM1s9jum3U5F
KReBigp1qffRzSjUYhw8YRujkJPqB65cLGguRyPDkuUoDbLzhu2QBNXwlQvk2+rH
bgreE7hqmm2ZwRnjSwJFtrFSuOfULjBjXqv2QMG+Lby5e/VzrzV0wdZJd2YXk9VX
VzhjiHmAGI2l30JClGuz9wN2MXuvtQFr2dJF56Nuw535mwuBUzxQwXY5qkX6uJ1z
KXADrUz7atA2VVYRgPEj8D30c1RlAzmiPLTxLTKouk0LdcOih90z/SaT/qlUHfsA
7TUaYBJt6PKbmrGK+PxUTpw/M88w+frbcV+PZNAynLeJfiRROl1Yg/6Tc0QC9nts
cHs9Migp2tf37gEvYcXFEPHI/A+sfIb5RZuTQySpUN09vODb37cZXl+lI4FuLGcJ
F4d45b05gNcybt+SFj63CGpW+k4QO8M6TUzy7gvQ0DdUmhd0mEvAmGfEPBoaBsau
5uJEfOQ=
=0tyg
-----END PGP SIGNATURE-----
Merge tag 'sound-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"The most significant changes at this cycle are the Sound Open Firmware
support from Intel for the common DSP framework along with its support
for Intel platforms. It's a door opened to a real "free" firmware (in
the sense of FOSS), and other parties show interests in it.
In addition to SOF, we've got a bunch of updates and fixes as usual.
Some highlights are below.
ALSA core:
- Cleanups and fixes in ALSA timer code to cover some races spotted
by syzkaller
- Cleanups and fixes in ALSA sequencer code to cover some races,
again unsurprisingly, spotted by syzkaller
- Optimize the common page allocation helper with alloc_pages_exact()
ASoC:
- Add SOF core support, as well as Intel SOF platform support
- Generic card driver improvements: support for MCLK/sample rate
ratio and pin switches
- A big set of improvements to TLV320AIC32x4 drivers
- New drivers for Freescale audio mixers, several Intel machines,
several Mediatek machines, Meson G12A, Spreadtrum compressed audio
and DMA devices
HD-audio:
- A few Realtek codec fixes for reducing pop noises
- Quirks for Chromebooks
- Workaround for faulty connection report on AMD/Nvidia HDMI
Others:
- A quirk for Focusrite Scarlett Solo USB-audio
- Add support for MOTU 8pre FireWire
- 24bit sample format support in aloop
- GUS patch format support (finally, over a decade) in native emux
synth code"
* tag 'sound-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (375 commits)
ASoC: SOF: Fix unused variable warnings
ALSA: line6: toneport: Fix broken usage of timer for delayed execution
ALSA: aica: Fix a long-time build breakage
ALSA: hda/realtek - Support low power consumption for ALC256
ASoC: stm32: i2s: update pcm hardware constraints
ASoC: codec: hdac_hdmi: no checking monitor in hw_params
ASoC: mediatek: mt6358: save PGA for mixer control
ASoC: mediatek: mt6358: save output volume for mixer controls
ASoC: mediatek: mt6358: initialize setting when ramping volume
ASoC: SOF: core: fix undefined nocodec reference
ASoC: SOF: xtensa: fix undefined references
ASoC: SOF: Propagate sof_get_ctrl_copy_params() error properly
ALSA: hdea/realtek - Headset fixup for System76 Gazelle (gaze14)
ALSA: hda/intel: add CometLake PCI IDs
ALSA: hda/realtek - Support low power consumption for ALC295
ASoC: rockchip: Fix an uninitialized variable compile warning
ASoC: SOF: Fix a compile warning with CONFIG_PCI=n
ASoC: da7219: Fix a compile warning at CONFIG_COMMON_CLK=n
ASoC: sound/soc/sof/: fix kconfig dependency warning
ASoC: stm32: spdifrx: change trace level on iec control
...
This adds device tree binding documentation for the rWTM BIU mailbox
driver on the Armada 37xx SOC (EspressoBin, Turris Mox).
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
-----BEGIN PGP SIGNATURE-----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=YFiQ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This has two exciting community drivers for ARM Mali accelerators.
Since ARM has never been open source friendly on the GPU side of the
house, the community has had to create open source drivers for the
Mali GPUs. Lima covers the older t4xx and panfrost the newer 6xx/7xx
series. Well done to all involved and hopefully this will help ARM
head in the right direction.
There is also now the ability if you don't have any of the legacy
drivers enabled (pre-KMS) to remove all the pre-KMS support code from
the core drm, this saves 10% or so in codesize on my machine.
i915 also enable Icelake/Elkhart Lake Gen11 GPUs by default, vboxvideo
moves out of staging.
There are also some rcar-du patches which crossover with media tree
but all should be acked by Mauro.
Summary:
uapi changes:
- Colorspace connector property
- fourcc - new YUV formts
- timeline sync objects initially merged
- expose FB_DAMAGE_CLIPS to atomic userspace
new drivers:
- vboxvideo: moved out of staging
- aspeed: ASPEED SoC BMC chip display support
- lima: ARM Mali4xx GPU acceleration driver support
- panfrost: ARM Mali6xx/7xx Midgard/Bitfrost acceleration driver support
core:
- component helper docs
- unplugging fixes
- devm device init
- MIPI/DSI rate control
- shmem backed gem objects
- connector, display_info, edid_quirks cleanups
- dma_buf fence chain support
- 64-bit dma-fence seqno comparison fixes
- move initial fb config code to core
- gem fence array helpers for Lima
- ability to remove legacy support code if no drivers requires it (removes 10% of drm.ko size)
- lease fixes
ttm:
- unified DRM_FILE_PAGE_OFFSET handling
- Account for kernel allocations in kernel zone only
panel:
- OSD070T1718-19TS panel support
- panel-tpo-td028ttec1 backlight support
- Ronbo RB070D30 MIPI/DSI
- Feiyang FY07024DI26A30-D MIPI-DSI panel
- Rocktech jh057n00900 MIPI-DSI panel
i915:
- Comet Lake (Gen9) PCI IDs
- Updated Icelake PCI IDs
- Elkhartlake (Gen11) support
- DP MST property addtions
- plane and watermark fixes
- Icelake port sync and VEBOX disable fixes
- struct_mutex usage reduction
- Icelake gamma fix
- GuC reset fixes
- make mmap more asynchronous
- sound display power well race fixes
- DDI/MIPI-DSI clocks for Icelake
- Icelake RPS frequency changing support
- Icelake workarounds
amdgpu:
- Use HMM for userptr
- vega20 experimental smu11 support
- RAS support for vega20
- BACO support for vega12 + fixes for vega20
- reworked IH interrupt handling
- amdkfd RAS support
- Freesync improvements
- initial timeline sync object support
- DC Z ordering fixes
- NV12 planes support
- colorspace properties for planes=
- eDP opts if eDP already initialized
nouveau:
- misc fixes
etnaviv:
- misc fixes
msm:
- GPU zap shader support expansion
- robustness ABI addition
exynos:
- Logging cleanups
tegra:
- Shared reset fix
- CPU cache maintenance fix
cirrus:
- driver rewritten using simple helpers
meson:
- G12A support
vmwgfx:
- Resource dirtying management improvements
- Userspace logging improvements
virtio:
- PRIME fixes
rockchip:
- rk3066 hdmi support
sun4i:
- DSI burst mode support
vc4:
- load tracker to detect underflow
v3d:
- v3d v4.2 support
malidp:
- initial Mali D71 support in komeda driver
tfp410:
- omap related improvement
omapdrm:
- drm bridge/panel support
- drop some omap specific panels
rcar-du:
- Display writeback support"
* tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm: (1507 commits)
drm/msm/a6xx: No zap shader is not an error
drm/cma-helper: Fix drm_gem_cma_free_object()
drm: Fix timestamp docs for variable refresh properties.
drm/komeda: Mark the local functions as static
drm/komeda: Fixed warning: Function parameter or member not described
drm/komeda: Expose bus_width to Komeda-CORE
drm/komeda: Add sysfs attribute: core_id and config_id
drm: add non-desktop quirk for Valve HMDs
drm/panfrost: Show stored feature registers
drm/panfrost: Don't scream about deferred probe
drm/panfrost: Disable PM on probe failure
drm/panfrost: Set DMA masks earlier
drm/panfrost: Add sanity checks to submit IOCTL
drm/etnaviv: initialize idle mask before querying the HW db
drm: introduce a capability flag for syncobj timeline support
drm: report consistent errors when checking syncobj capibility
drm/nouveau/nouveau: forward error generated while resuming objects tree
drm/nouveau/fb/ramgk104: fix spelling mistake "sucessfully" -> "successfully"
drm/nouveau/i2c: Disable i2c bus access after ->fini()
drm/nouveau: Remove duplicate ACPI_VIDEO_NOTIFY_PROBE definition
...
-----BEGIN PGP SIGNATURE-----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=zjhI
-----END PGP SIGNATURE-----
Merge tag 'media/v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- remove the deprecated Zoran driver from staging
- new I2C driver: ST MIPID02 CSI-2 camera bridge
- new platform driver: Amlogic Meson AO CEC G12A Controller
- add support for USB audio via the media controller
- au0828 driver is now supported via the media controller on both on
media and on usbaudio
- new kernel test for the media device allocator
- add support for stateless decoder at vicodec driver
- lots of other driver improvements fixes and cleanups
* tag 'media/v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (218 commits)
media: dt-bindings: aspeed-video: Add missing memory-region property
media: platform: Aspeed: Make reserved memory optional
media: platform: Aspeed: Remove use of reset line
media: stm32-dcmi: return appropriate error codes during probe
media: vsp1: Add support for missing 16-bit RGB555 formats
media: vsp1: Add support for missing 16-bit RGB444 formats
media: vsp1: Add support for missing 32-bit RGB formats
media: v4l: Add definitions for missing 16-bit RGB555 formats
media: v4l: Add definitions for missing 16-bit RGB4444 formats
media: v4l: Add definitions for missing 32-bit RGB formats
media: zoran: remove deprecated driver
media: MAINTAINERS: Update AO CEC with ao-cec-g12a driver
media: platform: meson: Add Amlogic Meson G12A AO CEC Controller driver
media: dt-bindings: media: meson-ao-cec: Add G12A AO-CEC-B Compatible
media: cros-ec-cec: decrement HDMI device refcount
media: seco-cec: decrement HDMI device refcount
media: tegra_cec: use new cec_notifier_parse_hdmi_phandle helper
media: stih_cec: use new cec_notifier_parse_hdmi_phandle helper
media: s5p_cec: use new cec_notifier_parse_hdmi_phandle helper
media: meson: ao-cec: use new cec_notifier_parse_hdmi_phandle helper
...
Nex drivers:
- New driver for Bitmain BM1880 pin controller
- New driver for Mediatek MT8516
- New driver for Cirrus Logich Lochnagar PMIC pins
Updates:
- Incremental development on Renesas SH-PFC
- Incremental development on Intel pin controller and some
particular updates for Cedarfork.
- Pin configuration support in Allwinner SunXi drivers
- Suspend/resume support in the NXP/Freescale i.MX8MQ driver
- Support for more packaging of the ST Micro STM32
-----BEGIN PGP SIGNATURE-----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=ovk5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"It is pretty calm and chill in pin control for the moment. Just
incremental development.
There is an odd patch to the Super-H architecture, it's coming from
the maintainers so should be fine.
Summary:
New drivers:
- Bitmain BM1880 pin controller
- Mediatek MT8516
- Cirrus Logich Lochnagar PMIC pins
Updates:
- Incremental development on Renesas SH-PFC
- Incremental development on Intel pin controller and some particular
updates for Cedarfork.
- Pin configuration support in Allwinner SunXi drivers
- Suspend/resume support in the NXP/Freescale i.MX8MQ driver
- Support for more packaging of the ST Micro STM32"
* tag 'pinctrl-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: mcp23s08: Do not complain about unsupported params
pinctrl: Rework Kconfig dependency for BM1880 pinctrl driver
MAINTAINERS: Add entry for BM1880 pinctrl
pinctrl: Add pinctrl support for BM1880 SoC
dt-bindings: pinctrl: Add BM1880 pinctrl binding
pinctrl: stm32: check irq controller availability at probe
pinctrl: mediatek: Add MT8516 Pinctrl driver
pinctrl: zte: fix leaked of_node references
pinctrl: intel: Increase readability of intel_gpio_update_pad_mode()
pinctrl: intel: Retain HOSTSW_OWN for requested gpio pin
pinctrl: pistachio: fix leaked of_node references
pinctrl: sunxi: Support I/O bias voltage setting on H6
pinctrl: sunxi: Prepare for alternative bias voltage setting methods
pinctrl: st: fix leaked of_node references
pinctrl: samsung: fix leaked of_node references
pinctrl: stm32: align stm32mp157 pin names
pinctrl: stm32: add package information for stm32mp157c
pinctrl: stm32: introduce package support
dt-bindings: pinctrl: stm32: add new entry for package information
pinctrl: imx8mq: Add suspend/resume ops
...
This is mostly update of the usual drivers: qla2xxx, qedf, smartpqi,
hpsa, lpfc, ufs, mpt3sas, ibmvfc and hisi_sas. Plus number of minor
changes, spelling fixes and other trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXNIK0yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbeFAP4wsOm6
BNqDvLbF7gHAH+oSVAeENd9tepXG2xKbUHmLRgEA1wPaUxon8L8v/SSsqwewqMXP
y6CnU6aO2iaViTNBsPs=
=RX74
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, qedf, smartpqi,
hpsa, lpfc, ufs, mpt3sas, ibmvfc and hisi_sas. Plus number of minor
changes, spelling fixes and other trivia"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (298 commits)
scsi: qla2xxx: Avoid that lockdep complains about unsafe locking in tcm_qla2xxx_close_session()
scsi: qla2xxx: Avoid that qlt_send_resp_ctio() corrupts memory
scsi: qla2xxx: Fix hardirq-unsafe locking
scsi: qla2xxx: Complain loudly about reference count underflow
scsi: qla2xxx: Use __le64 instead of uint32_t[2] for sending DMA addresses to firmware
scsi: qla2xxx: Introduce the dsd32 and dsd64 data structures
scsi: qla2xxx: Check the size of firmware data structures at compile time
scsi: qla2xxx: Pass little-endian values to the firmware
scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands
scsi: qla2xxx: Use an on-stack completion in qla24xx_control_vp()
scsi: qla2xxx: Make qla24xx_async_abort_cmd() static
scsi: qla2xxx: Remove unnecessary locking from the target code
scsi: qla2xxx: Remove qla_tgt_cmd.released
scsi: qla2xxx: Complain if a command is released that is owned by the firmware
scsi: qla2xxx: target: Fix offline port handling and host reset handling
scsi: qla2xxx: Fix abort handling in tcm_qla2xxx_write_pending()
scsi: qla2xxx: Fix error handling in qlt_alloc_qfull_cmd()
scsi: qla2xxx: Simplify qlt_send_term_imm_notif()
scsi: qla2xxx: Fix use-after-free issues in qla2xxx_qpair_sp_free_dma()
scsi: qla2xxx: Fix a qla24xx_enable_msix() error path
...
Here is the "big" set of tty/serial driver patches for 5.2-rc1.
It's really pretty small, not much happening in this portion of the
kernel at the moment. When the "highlight" is the movement of the
documentation from .txt to .rst files, it's a good merge window.
There's a number of small fixes and updates over the various serial
drivers, and a new "tty null" driver for those embedded systems that
like to make things even smaller and not break things.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNKvrw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynR2wCfTrWM9Qm7oA1hgWeYZiLTrnYnOtsAoK4a629W
o7AAyVf8RJ4jdWaSgOqx
=9Dy/
-----END PGP SIGNATURE-----
Merge tag 'tty-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.2-rc1.
It's really pretty small, not much happening in this portion of the
kernel at the moment. When the "highlight" is the movement of the
documentation from .txt to .rst files, it's a good merge window.
There's a number of small fixes and updates over the various serial
drivers, and a new "tty null" driver for those embedded systems that
like to make things even smaller and not break things.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (45 commits)
tty: serial: add driver for the SiFive UART
dt-bindings: serial: add documentation for the SiFive UART driver
serial: uartps: Add support for cts-override
dt-bindings: xilinx-uartps: Add support for cts-override
serial: milbeaut_usio: Fix error handling in probe and remove
tty: rocket: deprecate the rp_ioctl
tty: rocket: Remove RCPK_GET_STRUCT ioctl
tty: update obsolete termios comment
tty: serial_core: fix error code returned by uart_register_driver()
serial: 8250-mtk: modify baudrate setting
serial: 8250-mtk: add follow control
docs: serial: convert docs to ReST and rename to *.rst
serial: 8250_exar: Adjust IOT2000 matching
TTY: serial_core, add ->install
serial: Fix using plain integer instead of Null pointer
tty:serial_core: Spelling mistake
tty: Add NULL TTY driver
tty: vt: keyboard: Allow Unicode compose base char
Revert "tty: fix NULL pointer issue when tty_port ops is not set"
serial: Add Milbeaut serial control
...
Here is the big set of USB and PHY driver patches for 5.2-rc1
There is the usual set of:
- USB gadget updates
- PHY driver updates and additions
- USB serial driver updates and fixes
- typec updates and new chips supported
- mtu3 driver updates
- xhci driver updates
- other tiny driver updates
Nothing really interesting, just constant forward progress.
All of these have been in linux-next for a while with no reported
issues. The usb-gadget and usb-serial trees were merged a bit "late",
but both of them had been in linux-next before they got merged here last
Friday.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNKuwg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymRUgCfa8Ri7KrCaBR5NHQcLhbdrX90ToQAmgNw7vpo
fqt0XpNM0CSa9O/gOr79
=8HFh
-----END PGP SIGNATURE-----
Merge tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 5.2-rc1
There is the usual set of:
- USB gadget updates
- PHY driver updates and additions
- USB serial driver updates and fixes
- typec updates and new chips supported
- mtu3 driver updates
- xhci driver updates
- other tiny driver updates
Nothing really interesting, just constant forward progress.
All of these have been in linux-next for a while with no reported
issues. The usb-gadget and usb-serial trees were merged a bit "late",
but both of them had been in linux-next before they got merged here
last Friday"
* tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (206 commits)
USB: serial: f81232: implement break control
USB: serial: f81232: add high baud rate support
USB: serial: f81232: clear overrun flag
USB: serial: f81232: fix interrupt worker not stop
usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA
usb: dwc3: Fix default lpm_nyet_threshold value
usb: dwc3: debug: Print GET_STATUS(device) tracepoint
usb: dwc3: Do core validation early on probe
usb: dwc3: gadget: Set lpm_capable
usb: gadget: atmel: tie wake lock to running clock
usb: gadget: atmel: support USB suspend
usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask
dwc2: gadget: Fix completed transfer size calculation in DDMA
usb: dwc2: Set lpm mode parameters depend on HW configuration
usb: dwc2: Fix channel disable flow
usb: dwc2: Set actual frame number for completed ISOC transfer
usb: gadget: do not use __constant_cpu_to_le16
usb: dwc2: gadget: Increase descriptors count for ISOC's
usb: introduce usb_ep_type_string() function
usb: dwc3: move synchronize_irq() out of the spinlock protected block
...
Document new generic property that designates the PMIC as the system's
power controller.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Maxim 77663 has a few minor differences in regards to hardware interface
and available capabilities by comparing it with 77620 and 20024 models,
hence re-use 77620 device-tree binding for the 77663.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the DT binding document for the onkey module of max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the DT binding document for the LEDs module of max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the DT binding document for the battery charger module of max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a DT binding document for max77650 ultra-low power PMIC. This
describes the core mfd device and the GPIO module.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The bindings for DMA are now common for both drivers of the USART
IP.
The node given as an example for USART in SPI mode has been updated in
order to include DMA bindings.
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
- Fix possible memory leak in reserved-memory failure case
- Support for DMA parent bus which are not a parent node
- Clang -Wunsequenced fix
- Remove some unnecessary prints on memory alloc failures
- Various printk msg and comment fixes
- Update DT schema tools repository location
- Convert simple-framebuffer binding to DT schema
- Bindings for isl68137 and ir38064 trivial devices
- New documentation on binding do's and don't's for binding writers to
ignore
-----BEGIN PGP SIGNATURE-----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=zBKC
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- Fix possible memory leak in reserved-memory failure case
- Support for DMA parent bus which are not a parent node
- Clang -Wunsequenced fix
- Remove some unnecessary prints on memory alloc failures
- Various printk msg and comment fixes
- Update DT schema tools repository location
- Convert simple-framebuffer binding to DT schema
- Bindings for isl68137 and ir38064 trivial devices
- New documentation on binding do's and don't's for binding writers to
ignore
* tag 'devicetree-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (22 commits)
of: unittest: Remove error printing on OOM
of: irq: Remove WARN_ON() for kzalloc() failure
dt-bindings: pinctrl: fix bias-pull,up typo
dt-bindings: Update schema project location to devicetree.org github group
of: fix clang -Wunsequenced for be32_to_cpu()
of/device.c: fix the wrong comments
dt-bindings: Add isl68137 as a trivial device
dt-bindings: Add ir38064 as a trivial device
of: del redundant type conversion
dt-bindings: mfd: axp20x: Add fallback for axp805
of: Improve of_phandle_iterator_next() error message
dt-bindings: connector: Spelling mistake
dt-bindings: Add schemas for simple-framebuffer
of: address: Add support for the parent DMA bus
of: address: Retrieve a parent through a callback in __of_translate_address
dt-bindings: bus: Add binding for the Allwinner MBUS controller
dt-bindings: interconnect: Add a dma interconnect name
of: use correct function prototype for of_overlay_fdt_apply()
of: reserved_mem: fix reserve memory leak
of: property: Document that of_graph_get_endpoint_by_regs needs of_node_put
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXNHNRQAKCRBiEGxRG/Sl
26r7AP0QapMWbN0YFvn5/TzIrkMBxz4ZXpWmCWtzpIkJRldAOAEAuhw8HgXPXZOQ
cn4VO+1zq5VBvJW+QqjqRXr0G6DaYAw=
=UVPc
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"LED core fixes and improvements:
- avoid races with workqueue
- Kconfig: pedantic cleanup
- small fixes for Flash class description
leds-lt3593:
- remove unneeded assignment in lt3593_led_probe
- drop pdata handling code
leds-blinkm:
- clean up double assignment to data->i2c_addr
leds-pca955x, leds-pca963x:
- revert ACPI support, as it turned out that there is no evidence
of officially registered ACPI IDs for these devices.
- make use of device property API
leds-as3645a:
- switch to fwnode property API
LED related addition to ACPI documentation:
- document how to refer to LEDs from remote nodes
LED related fix to ALSA line6/toneport driver:
- avoid polluting led_* namespace
And lm3532 driver relocation from MFD to LED subsystem, accompanied by
various improvements and optimizations; it entails also a change in
omap4-droid4-xt894.dts:
- leds: lm3532: Introduce the lm3532 LED driver
- mfd: ti-lmu: Remove LM3532 backlight driver references
- ARM: dts: omap4-droid4: Update backlight dt properties
- dt: lm3532: Add lm3532 dt doc and update ti_lmu doc"
* tag 'leds-for-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: avoid races with workqueue
ALSA: line6: Avoid polluting led_* namespace
leds: lm3532: Introduce the lm3532 LED driver
mfd: ti-lmu: Remove LM3532 backlight driver references
ARM: dts: omap4-droid4: Update backlight dt properties
dt: lm3532: Add lm3532 dt doc and update ti_lmu doc
leds: Small fixes for Flash class description
leds: blinkm: clean up double assignment to data->i2c_addr
leds: pca963x: Make use of device property API
leds: pca955x: Make use of device property API
leds: lt3593: Remove unneeded assignment in lt3593_led_probe
leds: lt3593: drop pdata handling code
leds: pca955x: Revert "Add ACPI support"
leds: pca963x: Revert "Add ACPI support"
drivers: leds: Kconfig: pedantic cleanups
ACPI: Document how to refer to LEDs from remote nodes
leds: as3645a: Switch to fwnode property API
Add initial support for the AT42QT1050 (QT1050) device. The device
supports up to five input keys, dependent on the mode. Since it adds only
the initial support, the "1 to 4 keys plus Guard Channel" mode isn't
supported.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here is the "real" big set of char/misc driver patches for 5.2-rc1
Loads of different driver subsystem stuff in here, all over the places:
- thunderbolt driver updates
- habanalabs driver updates
- nvmem driver updates
- extcon driver updates
- intel_th driver updates
- mei driver updates
- coresight driver updates
- soundwire driver cleanups and updates
- fastrpc driver updates
- other minor driver updates
- chardev minor fixups
Feels like this tree is getting to be a dumping ground of "small driver
subsystems" these days. Which is fine with me, if it makes things
easier for those subsystem maintainers.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHE2w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvyQCYj5vSHQ88yEU+bzwGzQQLOBWYIwCgm5Iku0Y3
f6V3MvRffg4qUp3cGbU=
=R37j
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.2-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc update part 2 from Greg KH:
"Here is the "real" big set of char/misc driver patches for 5.2-rc1
Loads of different driver subsystem stuff in here, all over the places:
- thunderbolt driver updates
- habanalabs driver updates
- nvmem driver updates
- extcon driver updates
- intel_th driver updates
- mei driver updates
- coresight driver updates
- soundwire driver cleanups and updates
- fastrpc driver updates
- other minor driver updates
- chardev minor fixups
Feels like this tree is getting to be a dumping ground of "small
driver subsystems" these days. Which is fine with me, if it makes
things easier for those subsystem maintainers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.2-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
intel_th: msu: Add current window tracking
intel_th: msu: Add a sysfs attribute to trigger window switch
intel_th: msu: Correct the block wrap detection
intel_th: Add switch triggering support
intel_th: gth: Factor out trace start/stop
intel_th: msu: Factor out pipeline draining
intel_th: msu: Switch over to scatterlist
intel_th: msu: Replace open-coded list_{first,last,next}_entry variants
intel_th: Only report useful IRQs to subdevices
intel_th: msu: Start handling IRQs
intel_th: pci: Use MSI interrupt signalling
intel_th: Communicate IRQ via resource
intel_th: Add "rtit" source device
intel_th: Skip subdevices if their MMIO is missing
intel_th: Rework resource passing between glue layers and core
intel_th: SPDX-ify the documentation
intel_th: msu: Fix single mode with IOMMU
coresight: funnel: Support static funnel
dt-bindings: arm: coresight: Unify funnel DT binding
coresight: replicator: Add new device id for static replicator
...
Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here, along
with some new IIO drivers.
Also we ended up deleting two drivers, making this pull request remove a
few hundred thousand lines of code, always a nice thing to see. Both of
the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from those
locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by the
various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come in
the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHGMQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynQRACgwtlC6DFsEFwCplYxQXP5uzuIVTMAoJ61xzC0
Qim7K31f5ulaa3GJuhzo
=zEY5
-----END PGP SIGNATURE-----
Merge tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver updates from Greg KH:
"Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here,
along with some new IIO drivers.
The "counter" subsystem was added in here as well, as it is needed by
the IIO drivers and subsystem.
Also we ended up deleting two drivers, making this pull request remove
a few hundred thousand lines of code, always a nice thing to see. Both
of the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from
those locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by
the various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come
in the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon"
[ I fixed up the warning myself - Linus ]
* tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (663 commits)
staging: kpc2000: kpc_spi: Fix build error for {read,write}q
Staging: rtl8192e: Remove extra space before break statement
Staging: rtl8192u: ieee80211: Fix if-else indentation warning
Staging: rtl8192u: ieee80211: Fix indentation errors by removing extra spaces
staging: most: cdev: fix chrdev_region leak in mod_exit
staging: wlan-ng: Fix improper SPDX comment style
staging: rtl8192u: ieee80211: Resolve ERROR reported by checkpatch
staging: vc04_services: bcm2835-camera: Compress two lines into one line
staging: rtl8723bs: core: Use !x in place of NULL comparison.
staging: rtl8723bs: core: Prefer using the BIT Macro.
staging: fieldbus: anybus-s: fix wait_for_completion_timeout return handling
staging: kpc2000: fix up build problems with readq()
staging: rtlwifi: move remaining phydm .h files
staging: rtlwifi: strip down phydm .h files
staging: rtlwifi: delete the staging driver
staging: fieldbus: anybus-s: rename bus id field to avoid confusion
staging: fieldbus: anybus-s: keep device bus id in bus endianness
Staging: sm750fb: Change *array into *const array
staging: rtl8192u: ieee80211: Fix spelling mistake
staging: rtl8192u: ieee80211: Replace bit shifting with BIT macro
...
- Fix a few memoryleaks
- Minor improvements to the card initialization sequence
- Partially support sleepy GPIO controllers for pwrseq eMMC
MMC host:
- alcor: Work with multiple-entry sglists
- alcor: Enable DMA for writes
- meson-gx: Improve tuning support
- meson-gx: Avoid clock glitch when switching to DDR modes
- meson-gx: Disable unreliable HS400 mode
- mmci: Minor updates for support of HW busy detection
- mmci: Support data transfers for the stm32_sdmmc variant
- mmci: Restructure code to better support different variants
- mtk-sd: Add support for version found on MT7620 family SOCs
- mtk-sd: Add support for the MT8516 version
- mtk-sd: Add Chaotian Jing as the maintainer
- sdhci: Reorganize request-code to convert from tasklet to workqueue
- sdhci_am654: Stabilize support for lower speed modes
- sdhci-esdhc-imx: Add HS400 support for iMX7ULP
- sdhci-esdhc-imx: Add support for iMX7ULP version
- sdhci-of-arasan: Allow to disable DCMDs via DT for CQE
- sdhci-of-esdhc: Add support for the ls1028a version
- sdhci-of-esdhc: Several fixups for errata
- sdhci-pci: Fix BYT OCP setting
- sdhci-pci: Add support for Intel CML
- sdhci-tegra: Add support for system suspend/resume
- sdhci-tegra: Add CQE support for Tegra186 WAR
- sdhci-tegra: Add support for Tegra194
- sdhci-tegra: Update HW tuning process
MEMSTICK:
- I volunteered to help as a maintainer for the memstick subsystem, which is
reflected by an update to the MAINTAINERS file. Changes are funneled through
my MMC git and we will use the linux-mmc mailing list.
MEMSTICK host:
- A few minor cleanups
-----BEGIN PGP SIGNATURE-----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=Ompt
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fix a few memoryleaks
- Minor improvements to the card initialization sequence
- Partially support sleepy GPIO controllers for pwrseq eMMC
MMC host:
- alcor: Work with multiple-entry sglists
- alcor: Enable DMA for writes
- meson-gx: Improve tuning support
- meson-gx: Avoid clock glitch when switching to DDR modes
- meson-gx: Disable unreliable HS400 mode
- mmci: Minor updates for support of HW busy detection
- mmci: Support data transfers for the stm32_sdmmc variant
- mmci: Restructure code to better support different variants
- mtk-sd: Add support for version found on MT7620 family SOCs
- mtk-sd: Add support for the MT8516 version
- mtk-sd: Add Chaotian Jing as the maintainer
- sdhci: Reorganize request-code to convert from tasklet to workqueue
- sdhci_am654: Stabilize support for lower speed modes
- sdhci-esdhc-imx: Add HS400 support for iMX7ULP
- sdhci-esdhc-imx: Add support for iMX7ULP version
- sdhci-of-arasan: Allow to disable DCMDs via DT for CQE
- sdhci-of-esdhc: Add support for the ls1028a version
- sdhci-of-esdhc: Several fixups for errata
- sdhci-pci: Fix BYT OCP setting
- sdhci-pci: Add support for Intel CML
- sdhci-tegra: Add support for system suspend/resume
- sdhci-tegra: Add CQE support for Tegra186 WAR
- sdhci-tegra: Add support for Tegra194
- sdhci-tegra: Update HW tuning process
MEMSTICK:
- I volunteered to help as a maintainer for the memstick subsystem,
which is reflected by an update to the MAINTAINERS file. Changes
are funneled through my MMC git and we will use the linux-mmc
mailing list.
MEMSTICK host:
- A few minor cleanups"
* tag 'mmc-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (87 commits)
mmc: sdhci-pci: Fix BYT OCP setting
dt-bindings: mmc: add DT bindings for ls1028a eSDHC host controller
mmc: alcor: Drop pointer to mmc_host from alcor_sdmmc_host
mmc: mtk-sd: select REGULATOR
mmc: mtk-sd: enable internal card-detect logic.
mmc: mtk-sd: add support for config found in mt7620 family SOCs.
mmc: mtk-sd: don't hard-code interrupt trigger type
mmc: core: Fix tag set memory leak
dt-bindings: mmc: Add support for MT8516 to mtk-sd
mmc: mmci: Prevent polling for busy detection in IRQ context
mmc: mmci: Cleanup mmci_cmd_irq() for busy detect
mmc: usdhi6rol0: mark expected switch fall-throughs
mmc: core: Verify SD bus width
mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP
mmc: sdhci-esdhc-imx: add pm_qos to interact with cpuidle
dt-bindings: mmc: fsl-imx-esdhc: add imx7ulp compatible string
mmc: meson-gx: add signal resampling tuning
mmc: meson-gx: remove Rx phase tuning
mmc: meson-gx: avoid clock glitch when switching to DDR modes
mmc: meson-gx: disable HS400
...
The phy_mode "2000base-x" is actually supposed to be "1000base-x", even
though the commit title of the original patch says otherwise.
Fixes: 55601a8806 ("net: phy: Add 2000base-x, 2500base-x and rxaui modes")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Mark UFS clk as critical on Hi-Silicon hi3660 SoCs
- Support for Cirrus Logic Lochnagar clks
* clk-hisi:
clk: hi3660: Mark clk_gate_ufs_subsys as critical
* clk-lochnagar:
clk: lochnagar: Add support for the Cirrus Logic Lochnagar
clk: lochnagar: Add initial binding documentation
* clk-allwinner:
clk: sunxi-ng: sun5i: Export the MBUS clock
clk: sunxi-ng: a83t: Add pll-video0 as parent of csi-mclk
clk: sunxi-ng: h6: Allow video & vpu clocks to change parent rate
clk: sunxi-ng: h6: Preset hdmi-cec clock parent
clk: sunxi: Add Kconfig options
clk: sunxi-ng: f1c100s: fix USB PHY gate bit offset
clk: sunxi-ng: Allow DE clock to set parent rate
* clk-rockchip:
clk: rockchip: undo several noc and special clocks as critical on rk3288
clk: rockchip: add a COMPOSITE_DIV_OFFSET clock-type
clk: rockchip: Turn on "aclk_dmac1" for suspend on rk3288
clk: rockchip: Limit use of USB PHY clock to USB on rk3288
clk: rockchip: Fix video codec clocks on rk3288
clk: rockchip: Make rkpwm a critical clock on rk3288
clk: rockchip: fix wrong clock definitions for rk3328
* clk-qoriq:
clk: qoriq: increase array size of cmux_to_group
dt-bindings: qoriq-clock: Add ls1028a chip compatible string
clk: qoriq: Add ls1028a clock configuration
clk: qoriq: add more PLL divider clocks support
dt-bindings: qoriq-clock: add more PLL divider clocks support
- Remove clk_readl() and introduce BE versions of basic clk types
* clk-doc:
clk: Drop duplicate clk_register() documentation
clk: Document and simplify clk_core_get_rate_nolock()
clk: Remove 'flags' member of struct clk_fixed_rate
clk: nxp: Drop 'flags' on fixed_rate clk macro
clk: Document __clk_mux_determine_rate()
clk: Document CLK_MUX_READ_ONLY mux flag
clk: Document deprecated things
clk: Collapse gpio clk kerneldoc
* clk-more-critical:
clk: highbank: Convert to CLK_IS_CRITICAL
* clk-meson: (21 commits)
clk: meson: axg-audio: add g12a support
clk: meson: axg-audio: don't register inputs in the onecell data
clk: meson: axg_audio: replace prefix axg by aud
dt-bindings: clk: axg-audio: add g12a support
clk: meson: meson8b: add the video decoder clock trees
clk: meson: meson8b: add the VPU clock trees
clk: meson: meson8b: add support for the GP_PLL clock on Meson8m2
clk: meson: meson8b: use a separate clock table for Meson8m2
dt-bindings: clock: meson8b: export the video decoder clocks
clk: meson-g12a: add video decoder clocks
dt-bindings: clock: meson8b: export the VPU clock
clk: meson-g12a: add PCIE PLL clocks
dt-bindings: clock: g12a-aoclk: expose CLKID_AO_CTS_OSCIN
clk: meson-pll: add reduced specific clk_ops for G12A PCIe PLL
dt-bindings: clock: meson8b: drop the "ABP" clock definition
clk: meson: g12a: add cpu clocks
dt-bindings: clk: g12a-clkc: add VDEC clock IDs
dt-bindings: clock: axg-audio: unexpose controller inputs
dt-bindings: clk: g12a-clkc: add PCIE PLL clock ID
clk: g12a-aoclk: re-export CLKID_AO_SAR_ADC_SEL clock id
...
* clk-basic-be:
clk: core: replace clk_{readl,writel} with {readl,writel}
clk: core: remove powerpc special handling
powerpc/512x: mark clocks as big endian
clk: mux: add explicit big endian support
clk: multiplier: add explicit big endian support
clk: gate: add explicit big endian support
clk: fractional-divider: add explicit big endian support
clk: divider: add explicit big endian support
HD702E lcd is FriendlyELEC developed eDP LCD panel with 800x1280
resolution. It has built in Goodix, GT9271 captive touchscreen
with backlight adjustable via PWM.
Add dt-bindings documentation for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190507130708.11255-1-jagan@amarulasolutions.com
One small feature was added this release but the bulk of the diffstat
and the changelog comes from the fact that several older drivers got
some fairly hefty reworks and a couple of new drivers were added:
- Support for detailed control of timing around chip selects from
Sowjanya Komatineni.
- A big set of fixes and imrovements for the Tegra114 driver from
Sowjanya Komatineni.
- A big simplification of the GPIO driver from Andrey Smirnov.
- DMA support and fixes for the Freescale LPSPI driver from Clark Wang.
- Fixes and optimizations for the bcm2835aux from Martin Sparl.
- New drivers for Mediatek MT7621 (graduated from staging) and Zynq QSPI.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlzQRTQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0GgAB/96xMofBtfeSNdZgXiF5a8LSDDmzJAF
VMy66Q0VN5JgF8bH11KIZKho/T4PgNaGdbOtBZN/bt+vKhO7ZdaGp4bdtKXLogr/
bKJ102mdFBHTNtOuY3wXJtHcYRj1TPx528weOu/VbUo/Yt+e3yRybMiVjOvuQGn8
KrSQvQRlqaZcxYBVEMg3AQB3dkTFo5/hN9ipWjrabApFhcSbybA6Ccd/2VB2JD2H
lJ04atW+hP9zQOhQJUolI5QGkRtHwV2t+iohMrqjW7bacGdbILfORgoKqpxTMaCl
vT7+2CV3OtGC0OZWdlzGrLPOMG94/nbXjzmfGuJ4KX9WiTEJcadt7OR1
=1Dfk
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"One small feature was added this release but the bulk of the diffstat
and the changelog comes from the fact that several older drivers got
some fairly hefty reworks and a couple of new drivers were added:
- Support for detailed control of timing around chip selects from
Sowjanya Komatineni.
- A big set of fixes and imrovements for the Tegra114 driver from
Sowjanya Komatineni.
- A big simplification of the GPIO driver from Andrey Smirnov.
- DMA support and fixes for the Freescale LPSPI driver from Clark
Wang.
- Fixes and optimizations for the bcm2835aux from Martin Sparl.
- New drivers for Mediatek MT7621 (graduated from staging) and Zynq
QSPI"
[ This is a so-called "evil merge" that additionally removes a warning
due to an unused variable 'i' introduced by commit 1dfbf334f1 ("spi:
ep93xx: Convert to use CS GPIO descriptors") - Linus ]
* tag 'spi-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (127 commits)
spi: rspi: Fix handling of QSPI code when transmit and receive
spi: atmel-quadspi: fix crash while suspending
spi: stm32: return the get_irq error
spi: tegra114: fix PIO transfer
spi: pxa2xx: fix SCR (divisor) calculation
spi: Clear SPI_CS_HIGH flag from bad_bits for GPIO chip-select
spi: ep93xx: Convert to use CS GPIO descriptors
spi: AD ASoC: declare missing of table
spi: spi-mem: zynq-qspi: Fix build error on architectures missing readsl/writesl
spi: stm32-qspi: manage the get_irq error case
spi/spi-bcm2835: Split transfers that exceed DLEN
spi: expand mode support
dt-bindings: spi: spi-mt65xx: add support for MT8516
spi: pxa2xx: Add support for Intel Comet Lake
spi/trace: Cap buffer contents at 64 bytes
spi: Release spi_res after finalizing message
spi: Remove warning in spi_split_transfers_maxsize()
spi: Remove one needless transfer speed fall back case
spi: sh-msiof: Document r8a77470 bindings
spi: pxa2xx: use a module softdep for dw_dmac
...
In terms of big picture changes this has been an extremely quiet release
however there's a lot of changes and a fairly big diffstat thanks to a
bunch of small fixes, mainly coming from Axel Lin. Thanks to his work
this release removes code overall even though we've added a new (albiet
fairly small) driver.
Notable things:
- A fix for a long standing issue with locking on error interrupts from
Steve Twiss.
- A new driver for ST Microelectonics STM32 PWR.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlzQQwITHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MUbB/4pB0EgsQbDYNX97W/20+PPRu4PJGeM
XCceiaERCEmlLSk2JHQ+Vu0Hx0Dzl1Pr2bRSp8MP4reBX3Ut2tD60R5K+xPxRf8o
+H004G+Uc9uf72mMCHUvrZqrVs656XeVjus8R4V6z8ExSumEXvsc7GZXJSREPJHm
cdmI/rKs93WOmOsN3pp31w9WHD9Q0eobzKniGP4XCOahlkNMESFbclxoqJW/6iiQ
hhKuYQ2U0rmivn/xlR41+4O/NFA6e/LW70BLe/bQr09oR5oAxgMt3wO1c1ghZHU/
mMEFqMDPnRk5MrxobKbWg6SjqsX2LBc1ss04Mic12e1czODGJ4we697T
=NH6Z
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"In terms of big picture changes this has been an extremely quiet
release however there's a lot of changes and a fairly big diffstat
thanks to a bunch of small fixes, mainly coming from Axel Lin. Thanks
to his work this release removes code overall even though we've added
a new (albiet fairly small) driver.
Notable things:
- A fix for a long standing issue with locking on error interrupts
from Steve Twiss.
- A new driver for ST Microelectonics STM32 PWR"
* tag 'regulator-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (134 commits)
regulator: core: simplify return value on suported_voltage
regulator: da9xxx: Switch to SPDX identifier
regulator: stm32-pwr: Remove unneeded .min_uV and .list_volage
regulator: stm32-pwr: Remove unneeded *desc from struct stm32_pwr_reg
regulator: ab3100: Set fixed_uV instead of min_uV for fixed regulators
regulator: ab3100: Constify regulator_ops and ab3100_regulator_desc
regulator: pv880x0: Switch to SPDX identifier
regulator: hi6xxx: Switch to SPDX identifier
regulator: vexpress: Switch to SPDX identifier
regulator: vexpress: Get rid of struct vexpress_regulator
regulator: sky81452: Switch to SPDX identifier
regulator: sky81452: Constify sky81452_reg_ops
regulator: sy8106a: Get rid of struct sy8106a
regulator: core: do not report EPROBE_DEFER as error but as debug
regulator: mt63xx: Switch to SPDX identifier
regulator: fan53555: Switch to SPDX identifier
regulator: fan53555: Clean up unneeded fields from struct fan53555_device_info
regulator: ltc3589: Switch to SPDX identifier
regulator: ltc3589: Get rid of struct ltc3589_regulator
regulator: ltc3589: Convert to use simplified DT parsing
...
- Add driver for Intersil ISL68137 PWM Controller
- Add driver for Lochnagar 2
- Add driver for Infineon IR38064 Voltage Regulator
- Add support for TMP75B to lm75 driver
- Convert documentation to ReST format
- Use request_muxed_region for Super-IO accesses in several drivers
- Add 'samples' attribute to ABI, and start using it
- Add support for custom sysfs attributes to pmbus drivers
(used in ISL68137 driver)
- Introduce HWMON_CHANNEL_INFO macro
- Automated changes:
- Use permission specific [SENSOR_][DEVICE_]ATTR variants
- Fix build warnings due to unused of_device_id structures
- Use HWMON_CHANNEL_INFO macro
- Various minor improvements and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJc0DPYAAoJEMsfJm/On5mBptsQAI4v81dXY+/nAETcvf8e3rX9
Q8NafLYedHzLP3OX1YUhPI9HLnTxe6bumhKEkQhYNrc0u5tgr05mxe/LL3L3IgNo
sB/Fz2ySWzgYRArsAPSbiyaj5BdW2dZapik8tdKRH8/6oAq9hvpcydmU468KaEH8
/oTOlgdSN2JQFPMF0XebtJxPjzmqITJ1LLR0XgNhdtIloU1NlmMGmTsEoKyQJlSJ
L5QImEeemGuEH+vO1Gct2Jb8RYO57DVFrs2W5pbJOdGQs+JfGzs2TrzS1AZc1UMt
YhGxFTjOmjZ5JQRWsg5yTE3RuhAQlDk4Y4BAlNg6TNYCXMDYSXbRjw8oNg8ou2ZD
tvY6DkjSTJVRZ5Xe4jkUaI/13kjCS+5Vacfxva/IvVbKz4RIr8bnMM4pJiAq8tQR
6Suv6ryzYXHHhj9PLRSM5kxbDmTvUtYVLJ1ObR4Uf5R8lCA+2zsBDzpT7bOaQ1t2
q7CTfRwBv9a06j1X1MGv0J8xocGymZUN/9sNoyKa8Bp16udx1+xpkAU4PjsnLcg3
Bra9O1lcOmzwm/Mifnd8Ahyf2pijlMoYFu5xNfoNxxd/m5IK5BiiP5fJ0uW8I+sQ
msKEOi8Xc4LhzrkN9+4nvayv8sSzDvrrVF5BQuVqzOyaZMef+Z/LcaR0qHtlwxhS
Emo4fYZm3KdzSH1cjAD6
=snUV
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- Add driver for Intersil ISL68137 PWM Controller
- Add driver for Lochnagar 2
- Add driver for Infineon IR38064 Voltage Regulator
- Add support for TMP75B to lm75 driver
- Convert documentation to ReST format
- Use request_muxed_region for Super-IO accesses in several drivers
- Add 'samples' attribute to ABI, and start using it
- Add support for custom sysfs attributes to pmbus drivers (used in
ISL68137 driver)
- Introduce HWMON_CHANNEL_INFO macro
- Automated changes:
- Use permission specific [SENSOR_][DEVICE_]ATTR variants
- Fix build warnings due to unused of_device_id structures
- Use HWMON_CHANNEL_INFO macro
- Various minor improvements and fixes
* tag 'hwmon-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (125 commits)
hwmon: (lm75) Add support for TMP75B
dt-bindings: hwmon: Add tmp75b to lm75.txt
hwmon: (s3c) Use dev_get_drvdata()
hwmon: (max6650) Drop call to thermal_cdev_update
docs: hwmon: remove the extension from .rst files
docs: hwmon: convert three docs to ReST format
hwmon: (max6650) add thermal cooling device capability
hwmon: (ina3221) Add voltage conversion time settings
hwmon: (ina3221) Do not read-back to cache reg_config
docs: hwmon: Add an index file and rename docs to *.rst
docs: hwmon: convert remaining files to ReST format
docs: hwmon: misc files: convert to ReST format
docs: hwmon: pmbus files: convert to ReST format
docs: hwmon: k8temp, w83793: convert to ReST format
docs: hwmon: da9052, da9055: convert to ReST format
docs: hwmon: wm831x, wm8350: convert to ReST format
docs: hwmon: dme1737, vt1211: convert to ReST format
docs: hwmon: ads1015: convert to ReST format
docs: hwmon: asc7621: convert to ReST format
docs: hwmon: ibmpowernv: convert to ReST format
...
* skx_*: Librarize it so that it can be shared between drivers (Qiuxu Zhuo)
* altera: Stratix10 improvements (Thor Thayer)
* The usual round of fixes, fixlets and cleanups
-----BEGIN PGP SIGNATURE-----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=GTck
-----END PGP SIGNATURE-----
Merge tag 'edac_for_5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
- amd64_edac: Family 0x17, models 0x30-.. enablement (Yazen Ghannam)
- skx_*: Librarize it so that it can be shared between drivers (Qiuxu Zhuo)
- altera: Stratix10 improvements (Thor Thayer)
- The usual round of fixes, fixlets and cleanups
* tag 'edac_for_5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
Revert "EDAC/amd64: Support more than two controllers for chip select handling"
arm64: dts: stratix10: Use new Stratix10 EDAC bindings
Documentation: dt: edac: Add Stratix10 Peripheral bindings
Documentation: dt: edac: Fix Stratix10 IRQ bindings
EDAC/altera, firmware/intel: Add Stratix10 ECC DBE SMC call
EDAC/altera: Initialize peripheral FIFOs in probe()
EDAC/altera: Do less intrusive error injection
EDAC/amd64: Adjust printed chip select sizes when interleaved
EDAC/amd64: Support more than two controllers for chip select handling
EDAC/amd64: Recognize x16 symbol size
EDAC/amd64: Set maximum channel layer size depending on family
EDAC/amd64: Support more than two Unified Memory Controllers
EDAC/amd64: Use a macro for iterating over Unified Memory Controllers
EDAC/amd64: Add Family 17h Model 30h PCI IDs
MAINTAINERS: Add entry for EDAC-I10NM
MAINTAINERS: Update entry for EDAC-SKYLAKE
EDAC, altera: Fix S10 Double Bit Error Notification
EDAC, skx, i10nm: Make skx_common.c a pure library
This adds device tree bindings for ARM Firmware Suite
flash partitioning used in NOR flashes on ARM reference
designs.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Add an example showing how to use the addr-gpios property to deal with a
system with limited IO space.
Cc: devicetree@vger.kernel.org
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Describe how to use the BCM963XX ImageTag format in a mixed flash layout
environment.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Add binding documentation for the standard CFE based BCM963XX flash
layout, found in most devices using a BCM63XX SoC with NOR flash.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
As of_get_mac_address now supports NVMEM under the hood, we need to update
the bindings documentation with the new nvmem-cell* properties, which would
mean copy&pasting a lot of redundant information to every binding
documentation currently referencing some of the MAC address properties.
So I've just removed all the references to the optional MAC address
properties and replaced them with the small note referencing
net/ethernet.txt file.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-05-05
Here's one more bluetooth-next pull request for 5.2:
- Fixed Command Complete event handling check for matching opcode
- Added support for Qualcomm WCN3998 controller, along with DT bindings
- Added default address for Broadcom BCM2076B1 controllers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ad67b74d24 ("printk: hash addresses printed with %p"),
i6300esb prints "____ptrval____" instead of actual addresses:
i6300ESB timer 0000:00:03.0: initialized (0x(____ptrval____)). heartbeat=30 sec (nowayout=1)
Instead of changing the print to "%px", and leaking kernel addresses,
just remove the print completely, cfr. e.g. commit 071929dbdd
("arm64: Stop printing the virtual memory layout").
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Convert the isl29018 device tree bindings to the new YAML format.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The commit adds mt8183 compatible node in binding document.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAly4rnMACgkQJWrqGEe9
VoSBzAgAmSx1rDxiX2033dhVvufCcqMQnkY1fguKo69lYkhgGI1EYwvq2NbGLCf4
rb7n+D1peYhzH/9GKz4/LPQPccoVIQnx9+Z+JMZRzyQ+Z73cuomX/DtQO0AsRZgE
bx88vsbQFtjWv0mVluIEs51e3B/4ya6KPotxUDcaAyp2s/VKPaEI1rpiteUx8lZC
QsPsYQG/ryYiBW0cmopRL6c7ZdXyWi5A0kEdypGyO8ybTxo8xBquFqhbraDlM4U2
2H3Ii3iV9HoVTyjG2nGIA094Ak0U029oWW+P9xAPf1L4z6WIVXD68sazpZng+t8s
HgWP7BYDpcdRj+/Dm1b+uoaJH1fvOQ==
=B7w9
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
Tegra186 Audio DMA controller has new updates from Tegra210 version.
Thus add new compatibility binding string and the same can be used
by Tegra194 as well.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here are the GNSS updates for 5.2-rc1; only a new u-blox compatible.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXMxkmAAKCRALxc3C7H1l
CEKsAP9U1BtmlNxN0wXh1XgDjDd2p+m5DbSNf0CMbAy0eAtPWQD/RUH/K9zO4GsN
V3Csn5pBUF9osH6fOy9/TKDPNqX+HQc=
=Iat7
-----END PGP SIGNATURE-----
Merge tag 'gnss-5.2-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/gnss into char-misc-next
Johan writes:
GNSS updates for 5.2-rc1
Here are the GNSS updates for 5.2-rc1; only a new u-blox compatible.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'gnss-5.2-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/gnss:
gnss: ubx: add u-blox,neo-6m compatible
dt-bindings: gnss: add u-blox,neo-6m compatible
With a total of 50 non-merge commits, this is not a large pull
request. Most of the changes are, again, in dwc2 (37%) and dwc3 (32%)
with the rest of it scattered among other UDCs, function drivers and
device-tree bindings.
No really big feature this time around apart from support to Amlogic
being added to both dwc3 and dwc2 drivers.
-----BEGIN PGP SIGNATURE-----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=k1p8
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.2 merge window
With a total of 50 non-merge commits, this is not a large pull
request. Most of the changes are, again, in dwc2 (37%) and dwc3 (32%)
with the rest of it scattered among other UDCs, function drivers and
device-tree bindings.
No really big feature this time around apart from support to Amlogic
being added to both dwc3 and dwc2 drivers.
* tag 'usb-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (50 commits)
usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA
usb: dwc3: Fix default lpm_nyet_threshold value
usb: dwc3: debug: Print GET_STATUS(device) tracepoint
usb: dwc3: Do core validation early on probe
usb: dwc3: gadget: Set lpm_capable
usb: gadget: atmel: tie wake lock to running clock
usb: gadget: atmel: support USB suspend
usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask
dwc2: gadget: Fix completed transfer size calculation in DDMA
usb: dwc2: Set lpm mode parameters depend on HW configuration
usb: dwc2: Fix channel disable flow
usb: dwc2: Set actual frame number for completed ISOC transfer
usb: gadget: do not use __constant_cpu_to_le16
usb: dwc2: gadget: Increase descriptors count for ISOC's
usb: introduce usb_ep_type_string() function
usb: dwc3: move synchronize_irq() out of the spinlock protected block
usb: dwc3: Free resource immediately after use
usb: dwc3: of-simple: Convert to bulk clk API
usb: dwc2: Delayed status support
usb: gadget: udc: lpc32xx: rework interrupt handling
...
We need this to make the usb-gadget branch merge cleaner. And for
testing to keep from hitting the same issues already fixed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document support for the R7S9210 (RZ/A2) SoC. Also explicitly document
bindings for the R7S72100 (RZ/A1) SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mainly some pca954x work, i.e. removal of unused platform data support
and added support for sysfs interface for manipulating/examining the
idle state. And then a mechanical cocci-style patch.
- change my e-mail address
- add a new compatible for Renesas R1EX24016 to the DT binding document
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEFp3rbAvDxGAT0sefEacuoBRx13IFAlzDBZkACgkQEacuoBRx
13J+WxAApI3pe1tgl0wbP3FgXWIhHvyuE0oGcT3tRl/yQ+0Qcb7mqQcwB/psH+09
zbGM6LvRPl9mmp3nLRPYTVBIt4gykttj4ccHpCFd3s96QgxtnK38L6xoN1bbbonp
UB4hrgaXqebXbWnZtTipXXdz54brOa7STO6vyqfsh8vuwVGJuYmlxDWbIr7nleOR
BcvRwQyasrgAD8Q3JdqLk7NuAaRiADAEysrlrM4Ud06Ry+MuTBha6QllWXHxQrrW
JNzbQQ3vmCIIbqenu2uuckAYwZ2ZSKIbA7ggXT6iJz7EJlG51Ra/joMNc49BVeK5
gTRra4zgQl2Ls1QkNG8wIY5dukMjNIIinPKzgLCaAWuEsZstxRXLGmetp4/SpSGI
x78Zbvzlf7qcK/gakOPXeQjWmpoEdc49EX1dbQbYCglyWFGy3ndWZX8Y6No5+Vts
EBHWUNxt8GPnNwp5LcO68tOyht9ooIMCrL4Y/NSP6xqW3piyg0eKFrvpGI5d6Qj7
mqXUJ5EDkgWiHIpMwJcEQPnsafQKqSPR/eWKeQJIrFVVIQ9eISRYYc3Eo/trv4ag
dmOfSv2iCAn3ODe/mwNseGft1Ito2Bo9CshXD6RGlZi7Wrq/fu89fVwm9v/nQf4j
Gm6x7FQiLQ6Uc40i4wMl49go7eYaI2AzzfSla+48iTU2+1A9WrI=
=NLBx
-----END PGP SIGNATURE-----
Merge tag 'at24-v5.2-updates-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-5.2
at24: updates for linux v5.2
- change my e-mail address
- add a new compatible for Renesas R1EX24016 to the DT binding document
Add pinctrl binding for Bitmain BM1880 SoC. The SoC is not capable
of handling pinconf, thereby supporting only pinmux and this limitation
is documented.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Rockchip rk3288 there's a hardware quirk where we need to assert
the reset signal to the PHY when we get a remote wakeup on one of the
two ports. Document this quirk in the bindings.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Various boards have an external VBUS supply regulator. This regulator
depends on the current mode of the controller which is defined as:
- dr_mode set to either "host" or "peripheral" (fixed value)
- dr_mode set to "otg", based on the OTG status the dwc2 controller
internally switches between "host" and "peripheral" mode (selection
happens at runtime)
Based on the current mode the regulator has to be enabled or disabled:
- host: provide power to the connected USB device, thus the regulator
has to be enabled
- peripheral: the host device to which the controller is connected
provides power, thus the regulator has to be disabled
Add the dt-bindings documentation for this property so .dts authors know
that this property exists and how it behaves.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external vbus supply")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Adds the bindings for the Amlogic G12A USB Glue HW.
The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only
A glue connects these both controllers to 2 USB2 PHYs,
and optionnally to an USB3+PCIE Combo PHY shared with the PCIE controller.
The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.
The PHYs phandles are passed to the Glue node since the Glue controls the
interface with the PHY, not the DWC3 controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Adds the specific compatible string for the DWC2 IP found in the
Amlogic G12A SoC Family.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes a shared typo in several qcom pinctrl dt-bindings.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add compatible string for Allwinner suniv timer which is similar to
sun4i timer.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Since a separate US ports lanes polarity inversion property is going to
be available the bindings doc-file should be updated with information
about swap-us-lanes bool property, which will be responsible for it.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following the same fashion with replicator DT binding, this patch is to
unify the DT binding for funnel to support static and dynamic modes;
finally we get the funnel DT binding as below:
Before patch:
Static funnel, aka. non-configurable funnel:
Not supported;
Dynamic funnel, aka. configurable funnel:
"arm,coresight-funnel", "arm,primecell";
After patch:
Static funnel:
"arm,coresight-static-funnel";
Dynamic funnel:
"arm,coresight-dynamic-funnel", "arm,primecell";
"arm,coresight-funnel", "arm,primecell"; (obsolete)
At the end of this patch, it gives an example for static funnel DT
binding, and updates the dynamic funnel example.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Wanglai Shi <shiwanglai@hisilicon.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CoreSight uses below bindings for replicator:
Dynamic replicator, aka. configurable replicator:
"arm,coresight-dynamic-replicator", "arm,primecell";
Static replicator, aka. non-configurable replicator:
"arm,coresight-replicator";
The compatible string "arm,coresight-replicator" is not an explicit
naming to express the replicator is 'static'. To unify the naming
convention, this patch introduces a new compatible string
"arm,coresight-static-replicator" for the static replicator; the
compatible string "arm,coresight-replicator" is kept for backward
compatibility, but tag it as obsolete and suggest to use the new
compatible string.
As result CoreSight replicator have below bindings:
Dynamic replicator:
"arm,coresight-dynamic-replicator", "arm,primecell";
Static replicator:
"arm,coresight-static-replicator";
"arm,coresight-replicator"; (obsolete)
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document SoC specific bindings for R-Car RZ/G1C(r8a77470) SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add binding documentation of spi-mt65xx for MT8516 SOC.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document SoC specific bindings for R-Car RZ/G1C(r8a77470) SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DT schema tools are moving from my personal GH repo to the
devicetree.org group on GH. The new location is here:
https://github.com/devicetree-org/dt-schema.git
The old repo will be kept as a mirror.
Signed-off-by: Rob Herring <robh@kernel.org>
Add devicetree binding documentation for PCIe in EP mode present in
AM654 SoC.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add the resource mapping table for AM654 SoC as defined in
http://downloads.ti.com/tisci/esd/latest/5_soc_doc/am6x/resasg_types.html
Introduce a new compatible for AM654 "ti,am654-sci" for using
this resource map table.
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that the code to support the legacy binding has been removed,
remove the documentation for it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missed documenting this property in the initial commit.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a required 'usb-phy' property, to obtain a phandle to the USB PHY
from devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the Azoteq IQS550/572/525 family of
trackpad/touchscreen controllers.
The driver has been tested with an IQS550EV02 evaluation board. A
demonstration of the driver's capabilities is available here:
https://youtu.be/sRNNx4XZBts
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Provide a simple driver for GPIO controllable vibrators.
It will be used by the Fairphone 2.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The isl68137 is a digital output 7-phrase configurable PWM controller
with an AVSBus interface from Intersil.
Signed-off-by: Patrick Venture <venture@google.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rob Herring <robh@kernel.org>
The ir38064 is a voltage regulator from Infineon.
Signed-off-by: Patrick Venture <venture@google.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Add DT binding documentation for the Linux driver for the SiFive
PRCI clock & reset control IP block, as found on the SiFive
FU540 chip.
This version includes changes requested by Stephen Boyd
<sboyd@kernel.org> and Rob Herring <robh@kernel.org>, and
fixes some errors in the initial version.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Megan Wachs <megan@sifive.com>
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
axp805 is actually compatible and used with axp806 as fallback.
But it's actually undocumented and trig a warning with checkpatch.
DT compatible string "x-powers,axp805" appears un-documented.
Add this compatible in the dt-bindings documentation.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add DT binding documentation for the Linux driver for the SiFive
asynchronous serial IP block.
This revision incorporates changes based on feedback from Rob
Herring <robh@kernel.org>.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: linux-serial@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flow control is configurable in xilinx-uartps
Add a dt binding to check for the same.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support. We migrate to MULTI_IRQ_HANDLER, bumps the IRQs to
offset 16, converts to SPARSE_IRQ, then we add proper subsystem
drivers in each subsystem for irqchip, GPIO and clocksource and
switch over to using these new drivers.
Next we modernize the NPE and QMGR drivers and push them down
into drivers/soc.
This has been tested on the IXP4xx NSLU2 and the Gateworks
GW2358-4.
-----BEGIN PGP SIGNATURE-----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=0U95
-----END PGP SIGNATURE-----
Merge tag 'ixp4xx-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/soc
This modernizes the IXP4xx platform and adds initial Device Tree
Support. We migrate to MULTI_IRQ_HANDLER, bumps the IRQs to
offset 16, converts to SPARSE_IRQ, then we add proper subsystem
drivers in each subsystem for irqchip, GPIO and clocksource and
switch over to using these new drivers.
Next we modernize the NPE and QMGR drivers and push them down
into drivers/soc.
This has been tested on the IXP4xx NSLU2 and the Gateworks
GW2358-4.
* tag 'ixp4xx-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik: (31 commits)
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
ARM: ixp4xx: Move IXP4xx QMGR and NPE headers
ARM: ixp4xx: Move NPE and QMGR to drivers/soc
ARM: dts: Add some initial IXP4xx device trees
ARM: ixp4xx: Add device tree boot support
ARM: ixp4xx: Add DT bindings
gpio: ixp4xx: Add OF probing support
gpio: ixp4xx: Add DT bindings
clocksource/drivers/ixp4xx: Add OF initialization support
clocksource/drivers/ixp4xx: Add DT bindings
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add support for ZynqMP fpga manager
- Defer some probes which depends on firmware driver to be ready
- Debugfs fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly0QlMACgkQykllyylKDCFYngCfZOByHuyiliPv+PSa6KCtCics
ccgAn3YC1zEfvh8pmj2t0cvO/EpV2pXC
=HBAL
-----END PGP SIGNATURE-----
Merge tag 'zynqmp-soc-for-v5.2' of https://github.com/Xilinx/linux-xlnx into arm/drivers
arm64: zynqmp: SoC changes for v5.2
- Add support for ZynqMP fpga manager
- Defer some probes which depends on firmware driver to be ready
- Debugfs fix
* tag 'zynqmp-soc-for-v5.2' of https://github.com/Xilinx/linux-xlnx:
fpga manager: Adding FPGA Manager support for Xilinx zynqmp
dt-bindings: fpga: Add bindings for ZynqMP fpga driver
firmware: xilinx: Add fpga API's
drivers: Defer probe if firmware is not ready
firmware: xilinx: fix debugfs write handler
Signed-off-by: Olof Johansson <olof@lixom.net>
This series of changes for ti-sysc interconnect target module driver
gets us to the point where we can actually drop legacy platform data
for many devices in favor of device tree data.
To do this, we improve ti-sysc driver not to rely on platform data
callbacks to manage module clocks, and handle more quirks needed for
some devices. Also few minor fixes are needed, but were considered
not needed to be sent separately as they only show up with this series.
Then we drop several thousands of lines of legacy platform data for
omap4, omap5, dra7, am335x and am437x. We drop platform data for mmc,
i2c, gpio and uart devices to start with as those are typically
easily tested on all devices. In case of unexpected issues, we can just
add back the legacy platform data for a single device type if needed.
Finally we add initial support for enabling and disabling some devices
without legacy platform data callbacks. I was planning on sending the
dropping of legacy platform data as a separate series, but already
applied Roger's patch on top and pushed it out.
Note that this series depends on related SoC and is based on those.
-----BEGIN PGP SIGNATURE-----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=HJlq
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.2/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
Driver changes for ti-sysc for v5.2 merge window
This series of changes for ti-sysc interconnect target module driver
gets us to the point where we can actually drop legacy platform data
for many devices in favor of device tree data.
To do this, we improve ti-sysc driver not to rely on platform data
callbacks to manage module clocks, and handle more quirks needed for
some devices. Also few minor fixes are needed, but were considered
not needed to be sent separately as they only show up with this series.
Then we drop several thousands of lines of legacy platform data for
omap4, omap5, dra7, am335x and am437x. We drop platform data for mmc,
i2c, gpio and uart devices to start with as those are typically
easily tested on all devices. In case of unexpected issues, we can just
add back the legacy platform data for a single device type if needed.
Finally we add initial support for enabling and disabling some devices
without legacy platform data callbacks. I was planning on sending the
dropping of legacy platform data as a separate series, but already
applied Roger's patch on top and pushed it out.
Note that this series depends on related SoC and is based on those.
* tag 'omap-for-v5.2/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (33 commits)
bus: ti-sysc: Add generic enable/disable functions
ARM: OMAP2+: Drop mcspi platform data for omap4
ARM: OMAP2+: Drop uart platform data for dra7
ARM: OMAP2+: Drop gpio platform data for dra7
ARM: OMAP2+: Drop i2c platform data for dra7
ARM: OMAP2+: Drop mmc platform data for dra7
ARM: OMAP2+: Drop uart platform data for omap5
ARM: OMAP2+: Drop gpio platform data for omap5
ARM: OMAP2+: Drop i2c platform data for omap5
ARM: OMAP2+: Drop mmc platform data for omap5
ARM: OMAP2+: Drop uart platform data for am33xx and am43xx
ARM: OMAP2+: Drop gpio platform data for am33xx and am43xx
ARM: OMAP2+: Drop i2c platform data for am33xx and am43xx
ARM: OMAP2+: Drop mmc platform data for am330x and am43xx
ARM: OMAP2+: Drop uart platform data for omap4
ARM: OMAP2+: Drop gpio platform data for omap4
ARM: OMAP2+: Drop i2c platform data for omap4
ARM: OMAP2+: Drop mmc platform data for omap4
Documentation: bus: ti-sysc: fix spelling mistakes "multipe" and "interconnet"
bus: ti-sysc: Detect DMIC for debugging
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The old "cooling-{min,max}-state" properties for thermal bindings were
ratified to "cooling-{min,max}-level" by commit eb168b70de ("of:
thermal: Fix inconsitency between cooling-*-state and cooling-*-level"),
which were later removed entirely by commit e04907dbc2 ("dt-bindings:
thermal: Remove "cooling-{min|max}-level" properties").
The pwm-fan binding, however, was apparently in-flight in parallel with
that ratification, and so managed to introduce an example of the old
properties which escaped the scope of the later cleanup and has thus
continued to be dutifully copied for new boards despite being useless.
Clean up these remaining undocumented anachronisms to minimise any
further confusion.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This PR is pretty significant, but it been mostly about:
- Fixing the DTC warnings in most of our DT. We're now down to 2
warnings, from several thousands.
- Fixing a good number of minor issues, typos, and so on thanks to the DT
validation tools
- Describe the MBUS controller and the special DMA RAM mapping on the A13
- Add support for the LRADC on the A83t
- Add support for the I2C bus used for the PMIC on the A33
- Start using the DT annotation /omit-if-no-ref/ on our pinctrl nodes
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXLmxsgAKCRDj7w1vZxhR
xQs0APwIUuCrLfRD0av6xeCI4bon+G6drCxNVqkgf/cm3sAd5AEAzd6Ok74CEJar
xlSPxgqpBxCVyt2bxQxfN5mch2OPKgA=
=HH/F
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT changes for 5.2
This PR is pretty significant, but it been mostly about:
- Fixing the DTC warnings in most of our DT. We're now down to 2
warnings, from several thousands.
- Fixing a good number of minor issues, typos, and so on thanks to the DT
validation tools
- Describe the MBUS controller and the special DMA RAM mapping on the A13
- Add support for the LRADC on the A83t
- Add support for the I2C bus used for the PMIC on the A33
- Start using the DT annotation /omit-if-no-ref/ on our pinctrl nodes
* tag 'sunxi-dt-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (65 commits)
ARM: dts: sun8i: a83t: Enable USB OTG controller on some boards
ARM: dtsi: axp81x: add USB power supply node
ARM: dts: sun5i: Reorder pinctrl nodes
ARM: dts: sun6i: i7: Remove useless property
ARM: dts: sun4i: lime: Fix the USB PHY ID detect GPIO properties
ARM: dts: sun4i: protab2: Remove stale pinctrl-names entry
ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI
ARM: dts: sun8i: v40: bananapi-m2-berry: Sort device node dereferences.
ARM: dts: sun5i: Add the MBUS controller
dt-bindings: sunxi: Add compatible for OrangePi 3 board
ARM: dts: sun8i: a83t: Add I2C2 pinmux setting for PE pins
dt-bindings: arm: sunxi: Add Beelink GS1 board
ARM: dts: sun8i: tbs-a711: Add support for volume keys input
ARM: dts: sunxi: Add R_LRADC support for A83T
ARM: dts: sunxi: Improve A33 NAND transfers by using DMA
ARM: dts: sun8i: tbs-a711: Enable UART2 (for NEO-6M GPS module)
ARM: dts: sunxi: Remove useless pinctrl nodes
ARM: dts: sunxi: Remove pinctrl groups setting bias
ARM: dts: sunxi: Remove useless address and size cells
ARM: dts: sunxi: Conform to DT spec for NAND controller
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This series of devicetree changes adds the l4 abe interconnect devices
and moves the devices to their right places in the hierarchy similar
to what we've already done for most l4 devices earlier. We first add
a shared omap4-mcpdm.dtsi to make adding omap4-l4-abe.dtsi easier for
the mcpdm changes. And as earlier, in case of unexpected trouble,
devices can be probed the old way by moving one device at a time to the
old place.
This series of changes depends on the ti-sysc driver changes for handling
the external optional clocks that the mcpdm relies on, and is based on
the related ti-sysc driver changes. Note that this series does not depend
on dropping of the leagcy platform data, but I already had those committed
along with the ti-sysc driver changes and noticed too late.
-----BEGIN PGP SIGNATURE-----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=P5Js
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.2/dt-ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omap4 and 5 l4 abe interconnect
This series of devicetree changes adds the l4 abe interconnect devices
and moves the devices to their right places in the hierarchy similar
to what we've already done for most l4 devices earlier. We first add
a shared omap4-mcpdm.dtsi to make adding omap4-l4-abe.dtsi easier for
the mcpdm changes. And as earlier, in case of unexpected trouble,
devices can be probed the old way by moving one device at a time to the
old place.
This series of changes depends on the ti-sysc driver changes for handling
the external optional clocks that the mcpdm relies on, and is based on
the related ti-sysc driver changes. Note that this series does not depend
on dropping of the leagcy platform data, but I already had those committed
along with the ti-sysc driver changes and noticed too late.
* tag 'omap-for-v5.2/dt-ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (44 commits)
ARM: dts: Add l4 abe interconnect hierarchy and ti-sysc data for omap5
ARM: dts: Add l4 abe interconnect hierarchy and ti-sysc data for omap4
ARM: dts: Add common mcpdm dts file for omap4
bus: ti-sysc: Add generic enable/disable functions
ARM: OMAP2+: Drop mcspi platform data for omap4
ARM: OMAP2+: Drop uart platform data for dra7
ARM: OMAP2+: Drop gpio platform data for dra7
ARM: OMAP2+: Drop i2c platform data for dra7
ARM: OMAP2+: Drop mmc platform data for dra7
ARM: OMAP2+: Drop uart platform data for omap5
ARM: OMAP2+: Drop gpio platform data for omap5
ARM: OMAP2+: Drop i2c platform data for omap5
ARM: OMAP2+: Drop mmc platform data for omap5
ARM: OMAP2+: Drop uart platform data for am33xx and am43xx
ARM: OMAP2+: Drop gpio platform data for am33xx and am43xx
ARM: OMAP2+: Drop i2c platform data for am33xx and am43xx
ARM: OMAP2+: Drop mmc platform data for am330x and am43xx
ARM: OMAP2+: Drop uart platform data for omap4
ARM: OMAP2+: Drop gpio platform data for omap4
ARM: OMAP2+: Drop i2c platform data for omap4
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This series of changes configures dra7 pcie x2 lane mode, configures
am43xx-epos-evm regulators and keypad wakeup source, and uses standard
reset-gpios instead of gpio-reset for n810.
We also need to split dra7 dtsi files for properly supporting dra76x
and am576 as some of the devices are different such as usb and pruss.
-----BEGIN PGP SIGNATURE-----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=uc0c
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.2/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omap variants
This series of changes configures dra7 pcie x2 lane mode, configures
am43xx-epos-evm regulators and keypad wakeup source, and uses standard
reset-gpios instead of gpio-reset for n810.
We also need to split dra7 dtsi files for properly supporting dra76x
and am576 as some of the devices are different such as usb and pruss.
* tag 'omap-for-v5.2/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7: Separate AM57 dtsi files
dt-binding: arm: omap: Add information for AM5748
ARM: dts: omap2420-n810: Use new CODEC reset pin name
ARM: dts: am43xx-epos-evm: Add matrix keypad as wakeup source
ARM: dts: am43xx-epos-evm: Keep DCDC3 regulator on in suspend to memory
ARM: dts: am43xx-epos-evm: Keep DCDC5 and DCDC6 always on
ARM: dts: dra7: Add properties to enable PCIe x2 lane mode
Signed-off-by: Olof Johansson <olof@lixom.net>
* Hi3660 SoC and related boards:
- Added DMA support for the uart nodes
- Added the asp DMA controller node
- Replaced dma-min-chan with dma-channel-mask to follow the binding
* Hi3670 SoC and related boards:
- Reused Hi3660 reset to support Hi3670, updated the binding
document and added dts node
- Reused Hi3660 MMC controller to support Hi3670, updated the
binding document and added related nodes to support SD and WiFi
for the SoC and hikey970 board
- Added UFS controller node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9+Sr
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm64-dt-for-5.2' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: Hisilicon SoCs DT updates for 5.2
* Hi3660 SoC and related boards:
- Added DMA support for the uart nodes
- Added the asp DMA controller node
- Replaced dma-min-chan with dma-channel-mask to follow the binding
* Hi3670 SoC and related boards:
- Reused Hi3660 reset to support Hi3670, updated the binding
document and added dts node
- Reused Hi3660 MMC controller to support Hi3670, updated the
binding document and added related nodes to support SD and WiFi
for the SoC and hikey970 board
- Added UFS controller node
* tag 'hisi-arm64-dt-for-5.2' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: hi3670: Add UFS controller support
arm64: dts: hi3660: Fixup unofficial dma-min-chan to dma-channel-mask
arm64: dts: hi3660: Add hisi asp dma device
arm64: dts: hi3660: Add dma to uart nodes
arm64: dts: hisilicon: hikey970: Add SD and WiFi support
arm64: dts: hisilicon: hi3670: Add MMC controller support
dt-bindings: mmc: Add HI3670 MMC controller binding
arm64: dts: hisilicon: hi3670: Add reset controller support
dt-bindings: reset: Add HI3670 reset controller binding
Signed-off-by: Olof Johansson <olof@lixom.net>
- Align xlnx-zynqmp-clk.h file name and separate
binding for clock driver
- Add TI quirks to zynqmp boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly0Q7IACgkQykllyylKDCHtLACfZGBpUNq5coHf3tQohyNyROnh
q9cAn11bsVu3/BDOYhAO9TzKuYtzCACh
=n0Wu
-----END PGP SIGNATURE-----
Merge tag 'zynqmp-dt-for-v5.2' of https://github.com/Xilinx/linux-xlnx into arm/dt
arm64: dts: zynqmp: DT changes for v5.2
- Align xlnx-zynqmp-clk.h file name and separate
binding for clock driver
- Add TI quirks to zynqmp boards
* tag 'zynqmp-dt-for-v5.2' of https://github.com/Xilinx/linux-xlnx:
arm64: zynqmp: dt: Add TI PHY quirk
dt-bindings: xilinx: Separate clock binding from firmware doc
include: dt-binding: clock: Rename zynqmp header file
Signed-off-by: Olof Johansson <olof@lixom.net>
and emmc cleanups for rk3399. New boards are the OrangePi (rk3399) and
NanoPi NEO4. Both the OrangePi as well as the NanoPC/Pie family also
directly got some additional features added after the boards itself.
The Rock960 family (rock960+ficus) got their power-tree cleaned to match
the schematics and also got hdmi-audio and their gpu enabled.
Mali support also got enabled on the RockPi4 and finally both
rk3328-rock64 and rk3328-roc-cc got some additional features.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlyjIrAQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgTCuB/9wEiNDr5DvIYHdQM0/TrAWzMepdaO2YAHI
5v2NaZ3l0LDB1yXEJUJn/f7PRbGW9IETaldXLWKca8g8zJq6tM60p4gWx0XHw2hq
szajRwBhbvo16u3vSNOJ1LlK8SdfI+ENx9129qWVtXToODK/0TIo+ubOpPT3uBxt
P2Og+2F0zoj1WSWTXPEaGexF0YnwRp1v5NODF9XV6jpB9wAL+CYsllse7GFLxc52
sdp2Lfp/r/3VzHOCDOJ8e9YPXmLIYrjBQNw12/XkGdbnMKucCnI8GYxdkU7gSUh8
9ryBAAjOWREopY8GwdBfX+C+l1AKUFi8YFvC6PCxqFoseglzvAK0
=/JXo
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
Core new soc features are hdmi-cec for rk3328, scheduler capacity-values
and emmc cleanups for rk3399. New boards are the OrangePi (rk3399) and
NanoPi NEO4. Both the OrangePi as well as the NanoPC/Pie family also
directly got some additional features added after the boards itself.
The Rock960 family (rock960+ficus) got their power-tree cleaned to match
the schematics and also got hdmi-audio and their gpu enabled.
Mali support also got enabled on the RockPi4 and finally both
rk3328-rock64 and rk3328-roc-cc got some additional features.
* tag 'v5.2-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (23 commits)
arm64: dts: rockchip: Decrease emmc-phy's drive impedance on rk3399-puma
arm64: dts: rockchip: Define drive-impedance-ohm for RK3399's emmc-phy.
arm64: dts: rockchip: Disable DCMDs on RK3399's eMMC controller.
arm64: dts: rockchip: Add nanopi4 ethernet phy
arm64: dts: rockchip: Add PWM fan for NanoPC-T4
arm64: dts: rockchip: Add the fusb typec manager to rk3399-orangepi
arm64: dts: rockchip: Specify vid supply for the rk3399-orangepi compass (AK09911)
arm64: dts: rockchip: Fix clock names and add missing supplies for bluetooth on rk3399-orangepi
arm64: dts: rockchip: Add 12V DCIN regulator to rk3399-ficus
arm64: dts: rockchip: Rename vcc_sys into vcc5v0_sys on rk3399-rock960
arm64: dts: rockchip: Add Nanopi NEO4 initial support
arm64: dts: rockchip: enable hdmi audio out for rk3399-rockpro64
arm64: dts: rockchip: Add support for the Orange Pi RK3399 board.
arm64: dts: rockchip: enable mali on rock960 boards
arm64: dts: rockchip: enable mali on Rock Pi 4
arm64: dts: rockchip: add rk3328-roc-cc cpu-supply entries for all cpu nodes
arm64: dts: rockchip: give some life to the rk3328-roc-cc leds
arm64: dts: rockchip: add #sound-dai-cells to HDMI of rk3328
arm64: dts: rockchip: add ir-receiver node on rk3328-rock64
arm64: dts: rockchip: add leds node on rk3328-rock64
...
Signed-off-by: Olof Johansson <olof@lixom.net>
of cleanups for rk3288 from that area, hdmi support for the old rk3066
a small rv1108-eglin-r1 cleanup and wifi+hdmi-cec for the tinker board.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlyjIKkQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgagZB/0djmLiIppQmphU5xz0nu9la/6qPpX2Mglk
3XIi/pQXu+O/1i4aNJJwvk9k6cmX7nbVG2vQlLcsM/XNq0fy8Y4on9UThohkg23p
Cf34w2pFn5Tp5bBTCWxa1LTi20UMVZsYZivy+/LdBlTIekEMNFHf6veIn8dBtnPW
nFjDuvlhZqg6CaxVZ9Vn6xN1ClqleR0LuUcEt2X6wE8UocDs/01wZffcFbs3K0Uo
mgz1vUd4DlhHJo2YlTa+T88OF13d7WXboNR67xJTlm69d0wfm+k3MFeZYAhiI4kx
HdsqS+ZZxzsos7X3QCDiXMCbd070yGiDudD3UY4VCKymx9DzGWmp
=YSCV
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
Quite a bit of love for the rk3288-veyron chromeos devices and a number
of cleanups for rk3288 from that area, hdmi support for the old rk3066
a small rv1108-eglin-r1 cleanup and wifi+hdmi-cec for the tinker board.
* tag 'v5.2-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: enable vop0 and hdmi nodes to rk3066a-mk808
ARM: dts: rockchip: add rk3066 hdmi nodes
ARM: dts: rockchip: Add device tree for rk3288-veyron-mighty
dt-bindings: ARM: dts: rockchip: Add bindings for rk3288-veyron-mighty
ARM: dts: rockchip: Add vdd_logic to rk3288-veyron
ARM: dts: rockchip: Add dvs-gpios to rk3288-veyron-jerry
ARM: dts: rockchip: Add rk3288-veyron-jerry rev 10-15
dt-bindings: ARM: dts: rockchip: Add rk3288-veyron-jerry rev 10-15
ARM: dts: rockchip: Fix gic/efuse sort ordering for rk3288
ARM: dts: rockchip: Enable WiFi on rk3288-tinker
ARM: dts: rockchip: add grf reference in rk3288 tsadc node
ARM: dts: rockchip: Enable HDMI CEC on rk3288-tinker-s
ARM: dts: rockchip: remove disable-wp from rv1108-elgin-r1 emmc node
Signed-off-by: Olof Johansson <olof@lixom.net>
Convert the tsl2772 device tree bindings to the new YAML format.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert the tsl2583 device tree bindings to the new YAML format.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add binding documentation of apmixedsys for MT8516 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add binding documentation of infracfg for MT8516 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add binding documentation of topckgen for MT8516 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add compatible for i.MX8MQ and add i.MX7D/S, i.MX7ULP and i.M8MQ
to the description.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The STM32 LP Timer counter driver now resides under the Counter
subsystem. This patch adjusts dt-bindings to account for the STM32
lptimer driver move.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add bindings for STM32 Timer quadrature encoder.
It is a sub-node of STM32 Timer which implement the
quadratic encoder part of the hardware.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The simple-audio-card,pin-switches property can contain the list of
widget names for which pin switches must be created.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
STM32F769 clocks are derived from STM32746 clocks.
main differences are:
- new source clock for SAI1 and SAI2 (HSI or HSE)
- Add DFSDM & DSI clocks
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On Spreadtrum platform, the audio subsystem will use the multi-channel
data transfer controller to transfer sound stream between audio subsystem
and other AP/CP subsystem.
It can support 10 DAC channel and 10 ADC channel, and each channel has
512 bytes depth data fifo. Moreover each channel can be used DMA mode
or interrupt mode to transfer data.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the need for child nodes in the sckc binding to be able to remove
dtc warnings and have a more modern binding.
Also document optional properties.
Cc: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
More PLL divider clocks are needed by clock consumer IP. So update
the PLL divider description to make it more general.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Document the ast2400, ast2500 PCI-to-AHB bridge control driver bindings.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New device suport
* ad7606
- Support the AD7616 16 channel, 12bit ADC.
* fxas21002c
- New driver for this gyroscope with I2C and SPI support.
* lsm6dsx
- Support the lsm6dsr, new device information structure and dt bindings.
* srf04
- Addition device IDs for mb1000, mb1010, mb1020, mb1030 and mb1040 +
support of different required trigger pulse lengths.
* st-accel
- Support the ls2de12, new device info and dt bindings.
* ti-ads8344
- New driver for this 8 channel, 16 bit SPI ADC.
Binding conversions to yaml - we have started doing these in general for IIO.
* avia-hx711
* bmp085
Cleanups and minor fixes / additions
* ad5758
- Fixup for some changes between preproduction parts and final part.
* ad7606
- Refactor handling of oversampling to make it easy to vary between
supported devices.
* ad9832
- Organise includes.
- Clock framework to handle clocks.
* ad9834
- Drop unnecessary parenthesis.
* bmc150
- Use __func__ rather than hardcoding.
* dummy_evgen.
- Fix a memleak on error in probe.
* kxcjk1013
- Add KXCJ91008 ACPI ID as seen in the wild.
- Use __func__ rather than hardcoding.
* imx7d
- Local dev variable to simplify code a bit.
- dev_err replaces pr_err to give more info.
- devm_platform_ioremap_resource for small reduction in boilerplate.
- Simplify probe and remove by sharing suspend / resume logic.
- Devm for iio_device_register as remove only contains the unregister.
* lsm6dsx
- Remove a variable that was never read.
- Open code values where they are effectively described by what is assigned
to them rather than using uninformative defines.
* max31856
- Avoid an unintialized ret variable in a path that can't actually occur
but is hard for a static checker to know.
* max9611
- White space
* mpu3050
- Reduce a sleep worst case by switching from msleep to usleep_range.
* qcom-spmi-adc5
- Add MODULE_DEVICE_TABLE to assist autoloading of this as a module.
* stm32-dfsdm
- Fix missing dependencies.
* stm32-timer trigger
- Fix a build issue when disabled.
* ti-ads7950
- Fix mising dependency on CONFIG_GPIOLIB.
-----BEGIN PGP SIGNATURE-----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=McKo
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 5.2 cycle.
New device suport
* ad7606
- Support the AD7616 16 channel, 12bit ADC.
* fxas21002c
- New driver for this gyroscope with I2C and SPI support.
* lsm6dsx
- Support the lsm6dsr, new device information structure and dt bindings.
* srf04
- Addition device IDs for mb1000, mb1010, mb1020, mb1030 and mb1040 +
support of different required trigger pulse lengths.
* st-accel
- Support the ls2de12, new device info and dt bindings.
* ti-ads8344
- New driver for this 8 channel, 16 bit SPI ADC.
Binding conversions to yaml - we have started doing these in general for IIO.
* avia-hx711
* bmp085
Cleanups and minor fixes / additions
* ad5758
- Fixup for some changes between preproduction parts and final part.
* ad7606
- Refactor handling of oversampling to make it easy to vary between
supported devices.
* ad9832
- Organise includes.
- Clock framework to handle clocks.
* ad9834
- Drop unnecessary parenthesis.
* bmc150
- Use __func__ rather than hardcoding.
* dummy_evgen.
- Fix a memleak on error in probe.
* kxcjk1013
- Add KXCJ91008 ACPI ID as seen in the wild.
- Use __func__ rather than hardcoding.
* imx7d
- Local dev variable to simplify code a bit.
- dev_err replaces pr_err to give more info.
- devm_platform_ioremap_resource for small reduction in boilerplate.
- Simplify probe and remove by sharing suspend / resume logic.
- Devm for iio_device_register as remove only contains the unregister.
* lsm6dsx
- Remove a variable that was never read.
- Open code values where they are effectively described by what is assigned
to them rather than using uninformative defines.
* max31856
- Avoid an unintialized ret variable in a path that can't actually occur
but is hard for a static checker to know.
* max9611
- White space
* mpu3050
- Reduce a sleep worst case by switching from msleep to usleep_range.
* qcom-spmi-adc5
- Add MODULE_DEVICE_TABLE to assist autoloading of this as a module.
* stm32-dfsdm
- Fix missing dependencies.
* stm32-timer trigger
- Fix a build issue when disabled.
* ti-ads7950
- Fix mising dependency on CONFIG_GPIOLIB.
* tag 'iio-for-5.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (42 commits)
iio: adc: qcom-spmi-adc5: Fix of-based module autoloading
iio: dummy_evgen: fix possible memleak in evgen init
iio:accel:Switch hardcoded function name with a reference to __func__ making the code more maintainable
iio: adc: stm32-dfsdm: fix triggered buffer build dependency
iio: adc: stm32-dfsdm: fix unmet direct dependencies detected
iio: trigger: stm32-timer: fix build issue when disabled
iio: imx7d_adc: Use devm_iio_device_register()
iio: imx7d_adc: Simplify imx7d_adc_remove() with imx7d_adc_suspend()
iio: imx7d_adc: Simplify imx7d_adc_probe() with imx7d_adc_resume()
drivers/iio/gyro/mpu3050-core.c: This patch fix the following checkpatch warning.
iio: dac: ad5758: Modifications for new revision
iio: imu: st_lsm6dsx: inline per-sensor data
iio: adc: Add driver for the TI ADS8344 A/DC chips
dt-bindings: iio: adc: Add bindings for TI ADS8344 A/DC chips
MAINTAINERS: add entry for fxas21002c gyro driver
iio: gyro: fxas21002c: add spi driver
iio: gyro: fxas21002c: add i2c driver
iio: gyro: add core driver for fxas21002c
iio: gyro: add DT bindings to fxas21002c
Kconfig: change configuration of srf04 ultrasonic iio sensor
...
*) Add a new *release* phy_ops invoked when the consumer relinquishes PHY
that can be used to undo the operation performed in xlate
*) Add new driver to support USB2 PHY and shared USB3 + PCIE PHY in Amlogic
G12A SoC Family.
*) Add new driver to support for Broadcom's Stingray USB PHY (Type 1 has
one super speed PHY and one high speed PHY, Type 2 has one high speed PHY)
*) Add new driver to support USB PHY in hi3660 SoC of Hisilicon
*) Add new driver to support UFS M-PHY in MediaTek SoC
*) Add new driver to support XUSB pad controller in Tegra186 SoCs
*) Add new driver to support SERDES in TI's AM654 platform
*) Add support for generation 2 USB2 PHY and gneration 3 USB2 PHY in r8a77470
to phy-rcar-gen2.c and phy-rcar-gen3-usb2.c respectively
*) Add support for PCIe QMP PHY support in msm8998 to phy-qcom-qmp.c
*) Add support for SERDES6G in phy-ocelot-serdes.c
*) Add support to set drive impedance from device tree in phy-rockchip-emmc.c
*) Add support to power up/down the VBUS voltage rail in phy-fsl-imx8mq-usb.c
*) Add support to shut off regulators that power UFS during system suspend
*) Re-design phy-rcar-gen3-usb2.c to create separate PHY instances for each
channel which helps to enable/disable interrupts for each instance
independently
*) Fix PCIe power up sequence to follow the TRM in order to ensure the DPLL &
PHY operates correctly over the entire temperature range.
*) Use devm_clk_get_optional to get optional clocks instead of adding
custom error checks
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=BAzr
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.2
*) Add a new *release* phy_ops invoked when the consumer relinquishes PHY
that can be used to undo the operation performed in xlate
*) Add new driver to support USB2 PHY and shared USB3 + PCIE PHY in Amlogic
G12A SoC Family.
*) Add new driver to support for Broadcom's Stingray USB PHY (Type 1 has
one super speed PHY and one high speed PHY, Type 2 has one high speed PHY)
*) Add new driver to support USB PHY in hi3660 SoC of Hisilicon
*) Add new driver to support UFS M-PHY in MediaTek SoC
*) Add new driver to support XUSB pad controller in Tegra186 SoCs
*) Add new driver to support SERDES in TI's AM654 platform
*) Add support for generation 2 USB2 PHY and gneration 3 USB2 PHY in r8a77470
to phy-rcar-gen2.c and phy-rcar-gen3-usb2.c respectively
*) Add support for PCIe QMP PHY support in msm8998 to phy-qcom-qmp.c
*) Add support for SERDES6G in phy-ocelot-serdes.c
*) Add support to set drive impedance from device tree in phy-rockchip-emmc.c
*) Add support to power up/down the VBUS voltage rail in phy-fsl-imx8mq-usb.c
*) Add support to shut off regulators that power UFS during system suspend
*) Re-design phy-rcar-gen3-usb2.c to create separate PHY instances for each
channel which helps to enable/disable interrupts for each instance
independently
*) Fix PCIe power up sequence to follow the TRM in order to ensure the DPLL &
PHY operates correctly over the entire temperature range.
*) Use devm_clk_get_optional to get optional clocks instead of adding
custom error checks
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (51 commits)
dt-bindings: phy-qcom-qmp: Tweak qcom,msm8998-qmp-ufs-phy
dt-bindings: phy-qcom-qmp: Add qcom,msm8998-qmp-pcie-phy
phy: Add usb phy support for hi3660 Soc of Hisilicon
dt-bindings: phy: Add support for HiSilicon's hi3660 USB PHY
scsi: phy: mediatek: fix typo in author's email address
phy: ocelot-serdes: Add support for SERDES6G muxing
phy: fsl-imx8mq-usb: add support for VBUS power control
dt-bindings: phy-imx8mq-usb: add optional vbus supply regulator
phy: qcom-qmp: Add msm8998 PCIe QMP PHY support
phy: ti: am654-serdes: Support all clksel values
phy: ti: Add a new SERDES driver for TI's AM654x SoC
dt-bindings: phy: ti: Add dt binding documentation for SERDES in AM654x SoC
phy: core: Invoke pm_runtime_get_*/pm_runtime_put_* before invoking reset callback
phy: core: Add *release* phy_ops invoked when the consumer relinquishes PHY
phy: phy-meson-gxl-usb2: get optional clock by devm_clk_get_optional()
phy: socionext: get optional clock by devm_clk_get_optional()
phy: qcom-qusb2: get optional clock by devm_clk_get_optional()
phy: phy-mtk-tphy: get optional clock by devm_clk_get_optional()
phy: renesas: rcar-gen3-usb2: enable/disable independent irqs
phy: renesas: rcar-gen3-usb2: Use pdev's device pointer on dev_vdbg()
...
Some synthesis time configuration parameters of the DMA controller can be
inferred from the hardware itself.
Use this information as it is more reliably than the information specified
in the devicetree which might be outdated if the HDL project got changed.
Deprecate the devicetree properties that can be inferred from the hardware
itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
