Pull x86 perf fix from Ingo Molnar:
"An Intel RAPL events fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/rapl: Fix Haswell and Broadwell server RAPL event
Pull x86 pti updates from Thomas Gleixner:
"This contains:
- a PTI bugfix to avoid setting reserved CR3 bits when PCID is
disabled. This seems to cause issues on a virtual machine at least
and is incorrect according to the AMD manual.
- a PTI bugfix which disables the perf BTS facility if PTI is
enabled. The BTS AUX buffer is not globally visible and causes the
CPU to fault when the mapping disappears on switching CR3 to user
space. A full fix which restores BTS on PTI is non trivial and will
be worked on.
- PTI bugfixes for EFI and trusted boot which make sure that the user
space visible page table entries have the NX bit cleared
- removal of dead code in the PTI pagetable setup functions
- add PTI documentation
- add a selftest for vsyscall to verify that the kernel actually
implements what it advertises.
- a sysfs interface to expose vulnerability and mitigation
information so there is a coherent way for users to retrieve the
status.
- the initial spectre_v2 mitigations, aka retpoline:
+ The necessary ASM thunk and compiler support
+ The ASM variants of retpoline and the conversion of affected ASM
code
+ Make LFENCE serializing on AMD so it can be used as speculation
trap
+ The RSB fill after vmexit
- initial objtool support for retpoline
As I said in the status mail this is the most of the set of patches
which should go into 4.15 except two straight forward patches still on
hold:
- the retpoline add on of LFENCE which waits for ACKs
- the RSB fill after context switch
Both should be ready to go early next week and with that we'll have
covered the major holes of spectre_v2 and go back to normality"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
x86,perf: Disable intel_bts when PTI
security/Kconfig: Correct the Documentation reference for PTI
x86/pti: Fix !PCID and sanitize defines
selftests/x86: Add test_vsyscall
x86/retpoline: Fill return stack buffer on vmexit
x86/retpoline/irq32: Convert assembler indirect jumps
x86/retpoline/checksum32: Convert assembler indirect jumps
x86/retpoline/xen: Convert Xen hypercall indirect jumps
x86/retpoline/hyperv: Convert assembler indirect jumps
x86/retpoline/ftrace: Convert ftrace assembler indirect jumps
x86/retpoline/entry: Convert entry assembler indirect jumps
x86/retpoline/crypto: Convert crypto assembler indirect jumps
x86/spectre: Add boot time option to select Spectre v2 mitigation
x86/retpoline: Add initial retpoline support
objtool: Allow alternatives to be ignored
objtool: Detect jumps to retpoline thunks
x86/pti: Make unpoison of pgd for trusted boot work for real
x86/alternatives: Fix optimize_nops() checking
sysfs/cpu: Fix typos in vulnerability documentation
x86/cpu/AMD: Use LFENCE_RDTSC in preference to MFENCE_RDTSC
...
The intel_bts driver does not use the 'normal' BTS buffer which is exposed
through the cpu_entry_area but instead uses the memory allocated for the
perf AUX buffer.
This obviously comes apart when using PTI because then the kernel mapping;
which includes that AUX buffer memory; disappears. Fixing this requires to
expose a mapping which is visible in all context and that's not trivial.
As a quick fix disable this driver when PTI is enabled to prevent
malfunction.
Fixes: 385ce0ea4c ("x86/mm/pti: Add Kconfig")
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Reported-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: greg@kroah.com
Cc: hughd@google.com
Cc: luto@amacapital.net
Cc: Vince Weaver <vince@deater.net>
Cc: torvalds@linux-foundation.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180114102713.GB6166@worktop.programming.kicks-ass.net
Perf-fuzzer triggers non-existent MSR access in RAPL driver on
Haswell-EX.
Haswell/Broadwell server and client have differnt RAPL events.
Since 'commit 7f2236d0bf ("perf/x86/rapl: Use Intel family macros for
RAPL")', it accidentally assign RAPL client events to server.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linux-kernel@vger.kernel.org
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull more x86 pti fixes from Thomas Gleixner:
"Another small stash of fixes for fallout from the PTI work:
- Fix the modules vs. KASAN breakage which was caused by making
MODULES_END depend of the fixmap size. That was done when the cpu
entry area moved into the fixmap, but now that we have a separate
map space for that this is causing more issues than it solves.
- Use the proper cache flush methods for the debugstore buffers as
they are mapped/unmapped during runtime and not statically mapped
at boot time like the rest of the cpu entry area.
- Make the map layout of the cpu_entry_area consistent for 4 and 5
level paging and fix the KASLR vaddr_end wreckage.
- Use PER_CPU_EXPORT for per cpu variable and while at it unbreak
nvidia gfx drivers by dropping the GPL export. The subject line of
the commit tells it the other way around, but I noticed that too
late.
- Fix the ASM alternative macros so they can be used in the middle of
an inline asm block.
- Rename the BUG_CPU_INSECURE flag to BUG_CPU_MELTDOWN so the attack
vector is properly identified. The Spectre mitigations will come
with their own bug bits later"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pti: Rename BUG_CPU_INSECURE to BUG_CPU_MELTDOWN
x86/alternatives: Add missing '\n' at end of ALTERNATIVE inline asm
x86/tlb: Drop the _GPL from the cpu_tlbstate export
x86/events/intel/ds: Use the proper cache flush method for mapping ds buffers
x86/kaslr: Fix the vaddr_end mess
x86/mm: Map cpu_entry_area at the same place on 4/5 level
x86/mm: Set MODULES_END to 0xffffffffff000000
Thomas reported the following warning:
BUG: using smp_processor_id() in preemptible [00000000] code: ovsdb-server/4498
caller is native_flush_tlb_single+0x57/0xc0
native_flush_tlb_single+0x57/0xc0
__set_pte_vaddr+0x2d/0x40
set_pte_vaddr+0x2f/0x40
cea_set_pte+0x30/0x40
ds_update_cea.constprop.4+0x4d/0x70
reserve_ds_buffers+0x159/0x410
x86_reserve_hardware+0x150/0x160
x86_pmu_event_init+0x3e/0x1f0
perf_try_init_event+0x69/0x80
perf_event_alloc+0x652/0x740
SyS_perf_event_open+0x3f6/0xd60
do_syscall_64+0x5c/0x190
set_pte_vaddr is used to map the ds buffers into the cpu entry area, but
there are two problems with that:
1) The resulting flush is not supposed to be called in preemptible context
2) The cpu entry area is supposed to be per CPU, but the debug store
buffers are mapped for all CPUs so these mappings need to be flushed
globally.
Add the necessary preemption protection across the mapping code and flush
TLBs globally.
Fixes: c1961a4631 ("x86/events/intel/ds: Map debug buffers in cpu_entry_area")
Reported-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180104170712.GB3040@hirez.programming.kicks-ass.net
Pull perf fixes from Thomas Gleixner:
- plug a memory leak in the intel pmu init code
- clang fixes
- tooling fix to avoid including kernel headers
- a fix for jvmti to generate correct debug information for inlined
code
- replace backtick with a regular shell function
- fix the build in hardened environments
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Plug memory leak in intel_pmu_init()
x86/asm: Allow again using asm.h when building for the 'bpf' clang target
tools arch s390: Do not include header files from the kernel sources
perf jvmti: Generate correct debug information for inlined code
perf tools: Fix up build in hardened environments
perf tools: Use shell function for perl cflags retrieval
Pull x86 page table isolation updates from Thomas Gleixner:
"This is the final set of enabling page table isolation on x86:
- Infrastructure patches for handling the extra page tables.
- Patches which map the various bits and pieces which are required to
get in and out of user space into the user space visible page
tables.
- The required changes to have CR3 switching in the entry/exit code.
- Optimizations for the CR3 switching along with documentation how
the ASID/PCID mechanism works.
- Updates to dump pagetables to cover the user space page tables for
W+X scans and extra debugfs files to analyze both the kernel and
the user space visible page tables
The whole functionality is compile time controlled via a config switch
and can be turned on/off on the command line as well"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
x86/ldt: Make the LDT mapping RO
x86/mm/dump_pagetables: Allow dumping current pagetables
x86/mm/dump_pagetables: Check user space page table for WX pages
x86/mm/dump_pagetables: Add page table directory to the debugfs VFS hierarchy
x86/mm/pti: Add Kconfig
x86/dumpstack: Indicate in Oops whether PTI is configured and enabled
x86/mm: Clarify the whole ASID/kernel PCID/user PCID naming
x86/mm: Use INVPCID for __native_flush_tlb_single()
x86/mm: Optimize RESTORE_CR3
x86/mm: Use/Fix PCID to optimize user/kernel switches
x86/mm: Abstract switching CR3
x86/mm: Allow flushing for future ASID switches
x86/pti: Map the vsyscall page if needed
x86/pti: Put the LDT in its own PGD if PTI is on
x86/mm/64: Make a full PGD-entry size hole in the memory map
x86/events/intel/ds: Map debug buffers in cpu_entry_area
x86/cpu_entry_area: Add debugstore entries to cpu_entry_area
x86/mm/pti: Map ESPFIX into user space
x86/mm/pti: Share entry text PMD
x86/entry: Align entry text section to PMD boundary
...
A recent commit introduced an extra merge_attr() call in the skylake
branch, which causes a memory leak.
Store the pointer to the extra allocated memory and free it at the end of
the function.
Fixes: a5df70c354 ("perf/x86: Only show format attributes when supported")
Reported-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@linux.intel.com>
The BTS and PEBS buffers both have their virtual addresses programmed into
the hardware. This means that any access to them is performed via the page
tables. The times that the hardware accesses these are entirely dependent
on how the performance monitoring hardware events are set up. In other
words, there is no way for the kernel to tell when the hardware might
access these buffers.
To avoid perf crashes, place 'debug_store' allocate pages and map them into
the cpu_entry_area.
The PEBS fixup buffer does not need this treatment.
[ tglx: Got rid of the kaiser_add_mapping() complication ]
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Eduardo Valentin <eduval@amazon.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: aliguori@amazon.com
Cc: daniel.gruss@iaik.tugraz.at
Cc: keescook@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Intel PEBS/BTS debug store is a design trainwreck as it expects virtual
addresses which must be visible in any execution context.
So it is required to make these mappings visible to user space when kernel
page table isolation is active.
Provide enough room for the buffer mappings in the cpu_entry_area so the
buffers are available in the user space visible page tables.
At the point where the kernel side entry area is populated there is no
buffer available yet, but the kernel PMD must be populated. To achieve this
set the entries for these buffers to non present.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Eduardo Valentin <eduval@amazon.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: aliguori@amazon.com
Cc: daniel.gruss@iaik.tugraz.at
Cc: hughd@google.com
Cc: keescook@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[ Note, this is a Git cherry-pick of the following commit:
506458efaf ("locking/barriers: Convert users of lockless_dereference() to READ_ONCE()")
... for easier x86 PTI code testing and back-porting. ]
READ_ONCE() now has an implicit smp_read_barrier_depends() call, so it
can be used instead of lockless_dereference() without any change in
semantics.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1508840570-22169-4-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[ Note, this is a Git cherry-pick of the following commit:
a47ba4d77e ("perf/x86: Enable free running PEBS for REGS_USER/INTR")
... for easier x86 PTI code testing and back-porting. ]
Currently free running PEBS is disabled when user or interrupt
registers are requested. Most of the registers are actually
available in the PEBS record and can be supported.
So we just need to check for the supported registers and then
allow it: it is all except for the segment register.
For user registers this only works when the counter is limited
to ring 3 only, so this also needs to be checked.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170831214630.21892-1-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull misc x86 fixes from Ingo Molnar:
- topology enumeration fixes
- KASAN fix
- two entry fixes (not yet the big series related to KASLR)
- remove obsolete code
- instruction decoder fix
- better /dev/mem sanity checks, hopefully working better this time
- pkeys fixes
- two ACPI fixes
- 5-level paging related fixes
- UMIP fixes that should make application visible faults more debuggable
- boot fix for weird virtualization environment
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/decoder: Add new TEST instruction pattern
x86/PCI: Remove unused HyperTransport interrupt support
x86/umip: Fix insn_get_code_seg_params()'s return value
x86/boot/KASLR: Remove unused variable
x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
x86/pkeys/selftests: Fix protection keys write() warning
x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
x86/mpx/selftests: Fix up weird arrays
x86/pkeys: Update documentation about availability
x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
x86/smpboot: Fix __max_logical_packages estimate
x86/topology: Avoid wasting 128k for package id array
perf/x86/intel/uncore: Cache logical pkg id in uncore driver
x86/acpi: Reduce code duplication in mp_override_legacy_irq()
x86/acpi: Handle SCI interrupts above legacy space gracefully
x86/boot: Fix boot failure when SMP MP-table is based at 0
x86/mm: Limit mmap() of /dev/mem to valid physical addresses
x86/selftests: Add test for mapping placement for 5-level paging
...
Pull perf fixes from Ingo Molnar:
"Misc fixes: two PMU driver fixes and a memory leak fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix memory leak triggered by perf --namespace
perf/x86/intel/uncore: Add event constraint for BDX PCU
perf/x86/intel: Hide TSX events when RTM is not supported
The SNB-EP uncore driver is the only user of topology_phys_to_logical_pkg
in a performance critical path.
Change it query the logical pkg ID only once at initialization time and
then cache it in box structure. This allows to change the logical package
management without affecting the performance critical path.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: He Chen <he.chen@linux.intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Piotr Luc <piotr.luc@intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Mathias Krause <minipli@googlemail.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Link: https://lkml.kernel.org/r/20171114124257.22013-2-prarit@redhat.com
Pull x86 cleanups from Ingo Molnar:
"Two changes: Propagate const/__initconst, and use ARRAY_SIZE() some
more"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/events/amd/iommu: Make iommu_pmu const and __initconst
x86: Use ARRAY_SIZE
Pull perf updates from Ingo Molnar:
"The main changes in this cycle were:
Kernel:
- kprobes updates: use better W^X patterns for code modifications,
improve optprobes, remove jprobes. (Masami Hiramatsu, Kees Cook)
- core fixes: event timekeeping (enabled/running times statistics)
fixes, perf_event_read() locking fixes and cleanups, etc. (Peter
Zijlstra)
- Extend x86 Intel free-running PEBS support and support x86
user-register sampling in perf record and perf script. (Andi Kleen)
Tooling:
- Completely rework the way inline frames are handled. Instead of
querying for the inline nodes on-demand in the individual tools, we
now create proper callchain nodes for inlined frames. (Milian
Wolff)
- 'perf trace' updates (Arnaldo Carvalho de Melo)
- Implement a way to print formatted output to per-event files in
'perf script' to facilitate generate flamegraphs, elliminating the
need to write scripts to do that separation (yuzhoujian, Arnaldo
Carvalho de Melo)
- Update vendor events JSON metrics for Intel's Broadwell, Broadwell
Server, Haswell, Haswell Server, IvyBridge, IvyTown, JakeTown,
Sandy Bridge, Skylake, SkyLake Server - and Goldmont Plus V1 (Andi
Kleen, Kan Liang)
- Multithread the synthesizing of PERF_RECORD_ events for
pre-existing threads in 'perf top', speeding up that phase, greatly
improving the user experience in systems such as Intel's Knights
Mill (Kan Liang)
- Introduce the concept of weak groups in 'perf stat': try to set up
a group, but if it's not schedulable fallback to not using a group.
That gives us the best of both worlds: groups if they work, but
still a usable fallback if they don't. E.g: (Andi Kleen)
- perf sched timehist enhancements (David Ahern)
- ... various other enhancements, updates, cleanups and fixes"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (139 commits)
kprobes: Don't spam the build log with deprecation warnings
arm/kprobes: Remove jprobe test case
arm/kprobes: Fix kretprobe test to check correct counter
perf srcline: Show correct function name for srcline of callchains
perf srcline: Fix memory leak in addr2inlines()
perf trace beauty kcmp: Beautify arguments
perf trace beauty: Implement pid_fd beautifier
tools include uapi: Grab a copy of linux/kcmp.h
perf callchain: Fix double mapping al->addr for children without self period
perf stat: Make --per-thread update shadow stats to show metrics
perf stat: Move the shadow stats scale computation in perf_stat__update_shadow_stats
perf tools: Add perf_data_file__write function
perf tools: Add struct perf_data_file
perf tools: Rename struct perf_data_file to perf_data
perf script: Print information about per-event-dump files
perf trace beauty prctl: Generate 'option' string table from kernel headers
tools include uapi: Grab a copy of linux/prctl.h
perf script: Allow creating per-event dump files
perf evsel: Restore evsel->priv as a tool private area
perf script: Use event_format__fprintf()
...
0day testing reported a perf test regression on Haswell systems without
RTM. Commit a5df70c35 hides the in_tx/in_tx_cp attributes when RTM is not
available, but the TSX events are still available in sysfs. Due to the
missing attributes the event parser fails on those files.
Don't show the TSX events in sysfs when RTM is not available on
Haswell/Broadwell/Skylake.
Fixes: a5df70c354 (perf/x86: Only show format attributes when supported)
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Tested-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20171109000718.14137-1-andi@firstfloor.org
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit:
d2878d642a ("perf/x86/intel/bts: Disallow use by unprivileged users on paranoid systems")
... adds a privilege check in the exactly wrong place in the event init path:
after the 'LBR exclusive' reference has been taken, and doesn't release it
in the case of insufficient privileges. After this, nobody in the system
gets to use PT or LBR afterwards.
This patch moves the privilege check to where it should have been in the
first place.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: d2878d642a ("perf/x86/intel/bts: Disallow use by unprivileged users on paranoid systems")
Link: http://lkml.kernel.org/r/20171023123533.16973-1-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
READ_ONCE() now has an implicit smp_read_barrier_depends() call, so it
can be used instead of lockless_dereference() without any change in
semantics.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1508840570-22169-4-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull perf fixes from Ingo Molnar:
"Some tooling fixes plus three kernel fixes: a memory leak fix, a
statistics fix and a crash fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Fix memory leaks on allocation failures
perf/core: Fix cgroup time when scheduling descendants
perf/core: Avoid freeing static PMU contexts when PMU is unregistered
tools include uapi bpf.h: Sync kernel ABI header with tooling header
perf pmu: Unbreak perf record for arm/arm64 with events with explicit PMU
perf script: Add missing separator for "-F ip,brstack" (and brstackoff)
perf callchain: Compare dsos (as well) for CCKEY_FUNCTION
Currently if an allocation fails then the error return paths
don't free up any currently allocated pmus[].boxes and pmus causing
a memory leak. Add an error clean up exit path that frees these
objects.
Detected by CoverityScan, CID#711632 ("Resource Leak")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-janitors@vger.kernel.org
Fixes: 087bfbb032 ("perf/x86: Add generic Intel uncore PMU support")
Link: http://lkml.kernel.org/r/20171009172655.6132-1-colin.king@canonical.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull watchddog clean-up and fixes from Thomas Gleixner:
"The watchdog (hard/softlockup detector) code is pretty much broken in
its current state. The patch series addresses this by removing all
duct tape and refactoring it into a workable state.
The reasons why I ask for inclusion that late in the cycle are:
1) The code causes lockdep splats vs. hotplug locking which get
reported over and over. Unfortunately there is no easy fix.
2) The risk of breakage is minimal because it's already broken
3) As 4.14 is a long term stable kernel, I prefer to have working
watchdog code in that and the lockdep issues resolved. I wouldn't
ask you to pull if 4.14 wouldn't be a LTS kernel or if the
solution would be easy to backport.
4) The series was around before the merge window opened, but then got
delayed due to the UP failure caused by the for_each_cpu()
surprise which we discussed recently.
Changes vs. V1:
- Addressed your review points
- Addressed the warning in the powerpc code which was discovered late
- Changed two function names which made sense up to a certain point
in the series. Now they match what they do in the end.
- Fixed a 'unused variable' warning, which got not detected by the
intel robot. I triggered it when trying all possible related config
combinations manually. Randconfig testing seems not random enough.
The changes have been tested by and reviewed by Don Zickus and tested
and acked by Micheal Ellerman for powerpc"
* 'core-watchdog-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
watchdog/core: Put softlockup_threads_initialized under ifdef guard
watchdog/core: Rename some softlockup_* functions
powerpc/watchdog: Make use of watchdog_nmi_probe()
watchdog/core, powerpc: Lock cpus across reconfiguration
watchdog/core, powerpc: Replace watchdog_nmi_reconfigure()
watchdog/hardlockup/perf: Fix spelling mistake: "permanetely" -> "permanently"
watchdog/hardlockup/perf: Cure UP damage
watchdog/hardlockup: Clean up hotplug locking mess
watchdog/hardlockup/perf: Simplify deferred event destroy
watchdog/hardlockup/perf: Use new perf CPU enable mechanism
watchdog/hardlockup/perf: Implement CPU enable replacement
watchdog/hardlockup/perf: Implement init time detection of perf
watchdog/hardlockup/perf: Implement init time perf validation
watchdog/core: Get rid of the racy update loop
watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage
watchdog/sysctl: Clean up sysctl variable name space
watchdog/sysctl: Get rid of the #ifdeffery
watchdog/core: Clean up header mess
watchdog/core: Further simplify sysctl handling
watchdog/core: Get rid of the thread teardown/setup dance
...
Currently free running PEBS is disabled when user or interrupt
registers are requested. Most of the registers are actually
available in the PEBS record and can be supported.
So we just need to check for the supported registers and then
allow it: it is all except for the segment register.
For user registers this only works when the counter is limited
to ring 3 only, so this also needs to be checked.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170831214630.21892-1-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The lockup_detector_suspend/resume() interface is broken in several ways
especially as it results in recursive locking of the CPU hotplug lock.
Use the new stop/restart interface in the perf NMI watchdog to temporarily
disable and reenable the already active watchdog events. That's enough to
handle it.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Link: http://lkml.kernel.org/r/20170912194146.247141871@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 cache quality monitoring update from Thomas Gleixner:
"This update provides a complete rewrite of the Cache Quality
Monitoring (CQM) facility.
The existing CQM support was duct taped into perf with a lot of issues
and the attempts to fix those turned out to be incomplete and
horrible.
After lengthy discussions it was decided to integrate the CQM support
into the Resource Director Technology (RDT) facility, which is the
obvious choise as in hardware CQM is part of RDT. This allowed to add
Memory Bandwidth Monitoring support on top.
As a result the mechanisms for allocating cache/memory bandwidth and
the corresponding monitoring mechanisms are integrated into a single
management facility with a consistent user interface"
* 'x86-cache-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
x86/intel_rdt: Turn off most RDT features on Skylake
x86/intel_rdt: Add command line options for resource director technology
x86/intel_rdt: Move special case code for Haswell to a quirk function
x86/intel_rdt: Remove redundant ternary operator on return
x86/intel_rdt/cqm: Improve limbo list processing
x86/intel_rdt/mbm: Fix MBM overflow handler during CPU hotplug
x86/intel_rdt: Modify the intel_pqr_state for better performance
x86/intel_rdt/cqm: Clear the default RMID during hotcpu
x86/intel_rdt: Show bitmask of shareable resource with other executing units
x86/intel_rdt/mbm: Handle counter overflow
x86/intel_rdt/mbm: Add mbm counter initialization
x86/intel_rdt/mbm: Basic counting of MBM events (total and local)
x86/intel_rdt/cqm: Add CPU hotplug support
x86/intel_rdt/cqm: Add sched_in support
x86/intel_rdt: Introduce rdt_enable_key for scheduling
x86/intel_rdt/cqm: Add mount,umount support
x86/intel_rdt/cqm: Add rmdir support
x86/intel_rdt: Separate the ctrl bits from rmdir
x86/intel_rdt/cqm: Add mon_data
x86/intel_rdt: Prepare for RDT monitor data support
...
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- Add branch type profiling/tracing support. (Jin Yao)
- Add the PERF_SAMPLE_PHYS_ADDR ABI to allow the tracing/profiling of
physical memory addresses, where the PMU supports it. (Kan Liang)
- Export some PMU capability details in the new
/sys/bus/event_source/devices/cpu/caps/ sysfs directory. (Andi
Kleen)
- Aux data fixes and updates (Will Deacon)
- kprobes fixes and updates (Masami Hiramatsu)
- AMD uncore PMU driver fixes and updates (Janakarajan Natarajan)
On the tooling side, here's a (limited!) list of highlights - there
were many other changes that I could not list, see the shortlog and
git history for details:
UI improvements:
- Implement a visual marker for fused x86 instructions in the
annotate TUI browser, available now in 'perf report', more work
needed to have it available as well in 'perf top' (Jin Yao)
Further explanation from one of Jin's patches:
│ ┌──cmpl $0x0,argp_program_version_hook
81.93 │ ├──je 20
│ │ lock cmpxchg %esi,0x38a9a4(%rip)
│ │↓ jne 29
│ │↓ jmp 43
11.47 │20:└─→cmpxch %esi,0x38a999(%rip)
That means the cmpl+je is a fused instruction pair and they should
be considered together.
- Record the branch type and then show statistics and info about in
callchain entries (Jin Yao)
Example from one of Jin's patches:
# perf record -g -j any,save_type
# perf report --branch-history --stdio --no-children
38.50% div.c:45 [.] main div
|
---main div.c:42 (RET CROSS_2M cycles:2)
compute_flag div.c:28 (cycles:2)
compute_flag div.c:27 (RET CROSS_2M cycles:1)
rand rand.c:28 (cycles:1)
rand rand.c:28 (RET CROSS_2M cycles:1)
__random random.c:298 (cycles:1)
__random random.c:297 (COND_BWD CROSS_2M cycles:1)
__random random.c:295 (cycles:1)
__random random.c:295 (COND_BWD CROSS_2M cycles:1)
__random random.c:295 (cycles:1)
__random random.c:295 (RET CROSS_2M cycles:9)
namespaces support:
- Add initial support for namespaces, using setns to access files in
namespaces, grabbing their build-ids, etc. (Krister Johansen)
perf trace enhancements:
- Beautify pkey_{alloc,free,mprotect} arguments in 'perf trace'
(Arnaldo Carvalho de Melo)
- Add initial 'clone' syscall args beautifier in 'perf trace'
(Arnaldo Carvalho de Melo)
- Ignore 'fd' and 'offset' args for MAP_ANONYMOUS in 'perf trace'
(Arnaldo Carvalho de Melo)
- Beautifiers for the 'cmd' arg of several ioctl types, including:
sound, DRM, KVM, vhost virtio and perf_events. (Arnaldo Carvalho de
Melo)
- Add PERF_SAMPLE_CALLCHAIN and PERF_RECORD_MMAP[2] to 'perf data'
CTF conversion, allowing CTF trace visualization tools to show
callchains and to resolve symbols (Geneviève Bastien)
- Beautify the fcntl syscall, which is an interesting one in the
sense that infrastructure had to be put in place to change the
formatters of some arguments according to the value in a previous
one, i.e. cmd dictates how arg and the syscall return will be
formatted. (Arnaldo Carvalho de Melo
perf stat enhancements:
- Use group read for event groups in 'perf stat', reducing overhead
when groups are defined in the event specification, i.e. when using
{} to enclose a list of events, asking them to be read at the same
time, e.g.: "perf stat -e '{cycles,instructions}'" (Jiri Olsa)
pipe mode improvements:
- Process tracing data in 'perf annotate' pipe mode (David
Carrillo-Cisneros)
- Add header record types to pipe-mode, now this command:
$ perf record -o - -e cycles sleep 1 | perf report --stdio --header
Will show the same as in non-pipe mode, i.e. involving a perf.data
file (David Carrillo-Cisneros)
Vendor specific hardware event support updates/enhancements:
- Update POWER9 vendor events tables (Sukadev Bhattiprolu)
- Add POWER9 PMU events Sukadev (Bhattiprolu)
- Support additional POWER8+ PVR in PMU mapfile (Shriya)
- Add Skylake server uncore JSON vendor events (Andi Kleen)
- Support exporting Intel PT data to sqlite3 with python perf
scripts, this is in addition to the postgresql support that was
already there (Adrian Hunter)"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (253 commits)
perf symbols: Fix plt entry calculation for ARM and AARCH64
perf probe: Fix kprobe blacklist checking condition
perf/x86: Fix caps/ for !Intel
perf/core, x86: Add PERF_SAMPLE_PHYS_ADDR
perf/core, pt, bts: Get rid of itrace_started
perf trace beauty: Beautify pkey_{alloc,free,mprotect} arguments
tools headers: Sync cpu features kernel ABI headers with tooling headers
perf tools: Pass full path of FEATURES_DUMP
perf tools: Robustify detection of clang binary
tools lib: Allow external definition of CC, AR and LD
perf tools: Allow external definition of flex and bison binary names
tools build tests: Don't hardcode gcc name
perf report: Group stat values on global event id
perf values: Zero value buffers
perf values: Fix allocation check
perf values: Fix thread index bug
perf report: Add dump_read function
perf record: Set read_format for inherit_stat
perf c2c: Fix remote HITM detection for Skylake
perf tools: Fix static build with newer toolchains
...
Move the 'max_precise' capability into generic x86 code where it
belongs. This fixes a sysfs splat on !Intel systems where we fail to set
x86_pmu_caps_group.atts.
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hpa@zytor.com
Fixes: 22688d1c20f5 ("x86/perf: Export some PMU attributes in caps/ directory")
Link: http://lkml.kernel.org/r/20170828104650.2u3rsim4jafyjzv2@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For understanding how the workload maps to memory channels and hardware
behavior, it's very important to collect address maps with physical
addresses. For example, 3D XPoint access can only be found by filtering
the physical address.
Add a new sample type for physical address.
perf already has a facility to collect data virtual address. This patch
introduces a function to convert the virtual address to physical address.
The function is quite generic and can be extended to any architecture as
long as a virtual address is provided.
- For kernel direct mapping addresses, virt_to_phys is used to convert
the virtual addresses to physical address.
- For user virtual addresses, __get_user_pages_fast is used to walk the
pages tables for user physical address.
- This does not work for vmalloc addresses right now. These are not
resolved, but code to do that could be added.
The new sample type requires collecting the virtual address. The
virtual address will not be output unless SAMPLE_ADDR is applied.
For security, the physical address can only be exposed to root or
privileged user.
Tested-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: acme@kernel.org
Cc: mpe@ellerman.id.au
Link: http://lkml.kernel.org/r/1503967969-48278-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I just noticed that hw.itrace_started and hw.config are aliased to the
same location. Now, the PT driver happens to use both, which works out
fine by sheer luck:
- STORE(hw.itrace_start) is ordered before STORE(hw.config), in the
program order, although there are no compiler barriers to ensure that,
- to the perf_log_itrace_start() hw.itrace_start looks set at the same
time as when it is intended to be set because both stores happen in the
same path,
- hw.config is never reset to zero in the PT driver.
Now, the use of hw.config by the PT driver makes more sense (it being a
HW PMU) than messing around with itrace_started, which is an awkward API
to begin with.
This patch replaces hw.itrace_started with an attach_state bit and an
API call for the PMU drivers to use to communicate the condition.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/20170330153956.25994-1-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ldt->entries[] is allocated in alloc_ldt_struct(). It has
ldt->nr_entries elements and ldt->nr_entries is capped at LDT_ENTRIES.
So if "idx" is == ldt->nr_entries then we're reading beyond the end of
the buffer. It seems duplicative to have two limit checks when one
would work just as well so I removed the check against LDT_ENTRIES.
The gdt_page.gdt[] array has GDT_ENTRIES entries.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-janitors@vger.kernel.org
Fixes: d07bdfd322 ("perf/x86: Fix USER/KERNEL tagging of samples properly")
Link: http://lkml.kernel.org/r/20170818102516.gqwm4xdvvuvjw5ho@mwanda
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It can be difficult to figure out for user programs what features
the x86 CPU PMU driver actually supports. Currently it requires
grepping in dmesg, but dmesg is not always available.
This adds a caps directory to /sys/bus/event_source/devices/cpu/,
similar to the caps already used on intel_pt, which can be used to
discover the available capabilities cleanly.
Three capabilities are defined:
- pmu_name: Underlying CPU name known to the driver
- max_precise: Max precise level supported
- branches: Known depth of LBR.
Example:
% grep . /sys/bus/event_source/devices/cpu/caps/*
/sys/bus/event_source/devices/cpu/caps/branches:32
/sys/bus/event_source/devices/cpu/caps/max_precise:3
/sys/bus/event_source/devices/cpu/caps/pmu_name:skylake
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170822185201.9261-3-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Only show the Intel format attributes in sysfs when the feature is actually
supported with the current model numbers. This allows programs to probe
what format attributes are available, and give a sensible error message
to users if they are not.
This handles near all cases for intel attributes since Nehalem,
except the (obscure) case when the model number if known, but PEBS
is disabled in PERF_CAPABILITIES.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170822185201.9261-2-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Skylake changed the encoding of the PEBS data source field.
Some combinations are not available anymore, but some new cases
e.g. for L4 cache hit are added.
Fix up the conversion table for Skylake, similar as had been done
for Nehalem.
On Skylake server the encoding for L4 actually means persistent
memory. Handle this case too.
To properly describe it in the abstracted perf format I had to add
some new fields. Since a hit can have only one level add a new
field that is an enumeration, not a bit field to describe
the level. It can describe any level. Some numbers are also
used to describe PMEM and LFB.
Also add a new generic remote flag that can be combined with
the generic level to signify a remote cache.
And there is an extension field for the snoop indication to handle
the Forward state.
I didn't add a generic flag for hops because it's not needed
for Skylake.
I changed the existing encodings for older CPUs to also fill in the
new level and remote fields.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: jolsa@kernel.org
Link: http://lkml.kernel.org/r/20170816222156.19953-3-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Minor cleanup: use an explicit x86_pmu flag to handle the
missing Lock / TLB information on Nehalem, instead of always
checking the model number for each PEBS sample.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: jolsa@kernel.org
Link: http://lkml.kernel.org/r/20170816222156.19953-2-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
